MTRONPTI K1710AC 5v temperature compensated voltage controlled crystal oscillator Datasheet

K1700A Series
5V Temperature Compensated Voltage Controlled Crystal Oscillators
! Applications: Phase Lock Loops
Clocking “Sync” to NTSC Video Standards;
Reference Signal; Signal Tracking; ATM
! 2.0 to 35.0 MHz Frequency Range
! ±10ppm Frequency Stability - (0oC to 70oC) K1710
! ±20ppm Frequency Stability - (-40oC to 85oC) K1720
! -40°C to 85°C Operating Temperature
! TTL/CMOS Compatible
! Meets Stratum IV Stability Requirements
! Hermetically Sealed Package
ax.
mM
2m
13,
ax.
mM
m
8
20,
0AC Z
E
K170X.000 MHTE COD
2 TI DA
C
m
9m
7,4
x.
Ma
PIN 1
E L E C T R I C A L S P E C I F I C AT I O N S
Model
K1720ACM
K1710AC
Frequency Range (MHz)
2.0 to 35
Input Current (mA)
< 30
Frequency Control Function
(For Custom Deviation Range, Vc Range, etc. - Consult Factory)
Deviation (ppm)
Minimum (ppm)
±60
Maximum
±120
Linearity (%)
< 10
Modulation Bandwidth (±3dB)
> 20KHz
Nominal Control Voltage (V)
2.5
Control Voltage Range (V)
0.5 to 4.5
Transfer Function
Positive
Input Impedance
> 50KΩ @ 10KHz
Frequency Stability (ppm)
Inclusive of Calibration, Temperature, Voltage, Load, Aging
Overall
0oC to 70oC
-
±10
-40oC to 85oC
-
±20
Aging, 10 Years
±3.0
Temperature Range (oC)
0oC to +70oC
Operating
-40oC to +85oC
-40oC to +85oC
+5.0V ±5%
Storage
Supply Voltage (V)
45/55 < 16MHz; 40/60 ≥ 16MHz
Symmetry CMOS/TTL
Start Up Time (ms)
<10
Typical SSB Phase Noise (dBC/Hz)
10Hz
Offset from Carrier
100Hz
-65
-95
1KHz
-120
10KHz
-140
100KHz
-150
PA R T N U M B E R I N G G U I D E
K17X0AX - Specify Frequency
“Blank” = 0°C to 70°C Operating Temp.
“M” = -40°C to +85°C Operating Temp.
K1720 Only
“1” = ±10ppm, 0°C to 70°C Operating Temp.
“2” = ±20ppm, -40°C to +85°C Operating Temp.
2553 N. Edgington Street, Franklin Park, IL 60131 " Phone: 847.451.1000 " Fax: 847.451.7585
800-888-1499 or www.champtech.com
1
K1700A Series
5V Temperature Compensated Voltage Controlled Crystal Oscillators
PIN
FUNCTION
1
Voltage Control
7
Gnd/ & Case Gnd
8
Output
+ VCC
14
SHIPPING TUBE CROSS SECTION
TEST CIRCUIT DIAGRAM
OUTPUT WAVEFORM
MECHANICAL AND ENVIRONMENTAL SPECIFICATIONS
TEST METHODS
REFERENCE PROCEDURES
DESCRIPTION
Temperature Cycle
MIL-STD-833, Mtd 1010, Cond. B
-55°C to +125°C; Air-to-Air; 100 cycles; 10
min. dwell
Mechanical Shock
MIL-STD-883, Mtd 2002, Cond. B
1500 g’s
Vibration
MIL-STD 883, Mtd 2007, Cond. B
20-2000 Hz; 0.06 inch; 15g’s; 3 planes
Humidity Steady State
MIL-STD-202, Mtd 103
40°C; 90%-95% R.H.; 56 days
Thermal Shock
MIL-STD-883, Mtd 1011.7 Cond. B
100°C to 0°C; Water-to-Water; 15 cycles
Electrostatic Discharge
MIL-STD-883, Mtd 3015 Class II
2 KV to 4 KV Threshold
Solderability
Hermeticity
MIL-STD-883, Mtd 2022.2
MIL-STD-883, Mtd 1014.8, Cond. A1
Solder dip; Meniscograph Criteria
Mass spectro. 2 x 10-8 atmos. CC/sec He
Resistance to Soldering
Lead Integrity
MIL-STD-202, Mtd 210A, Cond. C
260°C; 10 seconds: 1 inch/sec.
MIL-STD-883, Mtd 2004.5, Cond. A, B1 Lead tension & bend stress
Marking Permanence
Life Test
MIL-STD-883, Mtd 2015.8
MIL-STD-883, Mtd 1005.6
Resistance to solvents
125°C, powered, 1000 hours minimum
2553 N. Edgington Street, Franklin Park, IL 60131 " Phone: 847.451.1000 " Fax: 847.451.7585
800-888-1499 or www.champtech.com
2
Similar pages