FAIRCHILD KM4470IP14TR3

www.fairchildsemi.com
KM4170, KM4270, KM4470
Low Cost, +2.7V & +5V, Rail-to-Rail I/O Amplifiers
Features at 2.7V
Description
•
•
•
•
•
•
•
•
The KM4170 (single), KM4270 (dual), and KM4470 (quad)
are ultra-low cost, low power, voltage feedback amplifiers.
At 5V, the KM4X70 family uses only 160µA of supply current
per amplifier and are designed to operate from a supply range
of 2.5V to 5.5V (±1.25 to ±2.75). The input voltage range
exceeds the negative and positive rails.
The KM4X70 family of amplifiers offer high bipolar
performance at a low CMOS prices. They offer superior
dynamic performance with 4.9MHz small signal bandwidths
and 5.3V/µs slew rates. The combination of low power, high
bandwidth, and rail-to-rail performance make the KM4X70
amplifiers well suited for battery-powered communication/
computing systems.
Large Signal Frequency Response
Vs = 5V
Applications
Portable/battery-powered applications
PCMCIA, USB
Mobile communications, cellular phones, pagers
Notebooks and PDA’s
Sensor Interface
A/D buffer
Active filters
Signal conditioning
Portable test instruments
Vo = 4Vpp
Vo = 2Vpp
0.01
0.1
1
10
Frequency (MHz)
Output Swing vs. Load
1.35
RL = 10kΩ
Output Voltage (0.27V/div)
•
•
•
•
•
•
•
•
•
Vo = 1Vpp
Magnitude (1dB/div)
136µA supply current per amplifier
4.9MHz bandwidth
Output swings to within 20mV of either rail
Input voltage range exceeds the rail by >250mV
5.3V/µs slew rate
16mA output current
21nV/√Hz input voltage noise
KM4170:
directly replaces OPA340, OPA343, and TLV2461 in
single supply applications and available in SC70-5 and
SOT23-5 package options
• KM4270:
directly replaces MAX4126, OPA2340, LMV822 and
TLV2462 in single supply applications and available in
SOIC-8 and MSOP-8 package options
• KM4470:
directly replaces MAX4129, OPA4340, LMV824 and
TLV2464 in single supply applications and available in
TSSOP-14 package option
RL = 1kΩ
RL = 75Ω
0
RL = 100Ω
RL = 200Ω
RL = 75/100Ω
-1.35
-2.0
0
2.0
Input Voltage (0.4V/div)
REV. 5 December 2002
DATA SHEET
KM4170, KM4270, KM4470
KM4170
SOT23-5
-Vs
2
+In
3
5
+Vs
-
4
-In
Out
1
-Vs
2
+In
3
+
1
+
Out
SC70-5
5
+Vs
4
-In
8
+Vs
7
Out2
6
-In2
5
+In2
-
KM4270
MSOP
SOIC
Out1
1
-In1
2
+In1
3
-Vs
4
+
+
8
+Vs
Out1
1
7
Out2
-In1
2
6
-In2
+In1
3
5
+In2
-Vs
4
+
+
KM4470
TSSOP
2
Out1
1
14
-In1
2
13
+In1
3
12
+Vs
4
11
+In2
5
10
-In2
6
9
REV. 5 December 2002
KM4170, KM4270, KM4470
DATA SHEET
Absolute Maximum Ratings
Parameter
Supply Voltages
Maximum Junction Temperature
Storage Temperature Range
Lead Temperature, 10 seconds
Operating Temperature Range, recommended
Input Voltage Range
Iout Continuous
Min.
0
–
-65
–
-40
-Vs -0.5
-30
Max.
+6
+175
+150
+260
+85
+Vs +0.5
+30
Unit
V
°C
°C
°C
°C
V
mA
Max.
Unit
Electrical Specifications
(Vs = +2.7V, G = 2, RL = 10kΩ to Vs/2, Rf = 5kΩ; unless otherwise noted)
Parameter
AC Performance
-3dB Bandwidth1
Full Power Bandwidth
Gain Bandwidth Product
Rise and Fall Time
Overshoot
Slew Rate
2nd Harmonic Distortion
3rd Harmonic Distortion
THD
Input Voltage Noise
DC Performance
Input Offset Voltage2
Average Drift
Input Bias Current2
Average Drift
Power Supply Rejection Ratio2
Open Loop Gain
Quiescent Current Per Channel2
Input Characteristics
Input Resistance
Input Capacitance
Input Common Mode Voltage Range
Common Mode Rejection Ratio2
Output Characteristics
Output Voltage Swing2
Conditions
Min.
G = +1, Vo = 0.02Vpp
G = +2, Vo = 0.2Vpp
G = +2, Vo = 2Vpp
4.9
3.7
1.4
2.2
163
<1
5.3
-72
-72
0.03
21
1V step
1V step
1V step
1Vpp, 10kHz
1Vpp, 10kHz
1Vpp, 10kHz
>10kHz
-6
DC
RL = 10kΩ
DC, Vcm = 0V to Vs
RL = 10kΩ to Vs/2
RL = 1kΩ to Vs/2
RL = 200Ω to Vs/2
Output Current
Power Supply Operating Range
Typ.
55
0.5
5
90
32
83
90
136
MHz
MHz
MHz
MHz
ns
%
V/µs
dBc
dBc
%
nV/√Hz
+6
420
190
mV
µV/°C
nA
pA/°C
dB
dB
µA
12
2
-0.25 to 2.95
81
MΩ
pF
V
dB
0.06 to 2.64 0.02 to 2.68
0.05 to 2.63
0.11 to 2.52
±16
2.5
2.7
V
V
V
mA
V
55
5.5
Min/max ratings are based on product characterization and simulation. Individual parameters are tested as noted. Outgoing quality levels are
determined from tested parameters.
Notes:
1. For G = +1, Rf = 0.
2. For RL = 10kΩ, KM4170, KM4270, and KM4470 are 100% tested at 25°C.
REV. 5 December 2002
3
DATA SHEET
KM4170, KM4270, KM4470
Electrical Specifications
(Vs = +5V, G = 2, RL = 10kΩ to Vs/2, Rf = 5kΩ; unless otherwise noted)
Parameter
AC Performance
-3dB Bandwidth1
Full Power Bandwidth
Gain Bandwidth Product
Rise and Fall Time
Overshoot
Slew Rate
2nd Harmonic Distortion
3rd Harmonic Distortion
THD
Input Voltage Noise
DC Performance
Input Offset Voltage2
Average Drift
Input Bias Current2
Average Drift
Power Supply Rejection Ratio2
Open Loop Gain
Quiescent Current Per Channel2
Input Characteristics
Input Resistance
Input Capacitance
Input Common Mode Voltage Range
Common Mode Rejection Ratio2
Output Characteristics
Output Voltage Swing2
Conditions
Min.
G = +1, Vo = 0.02Vpp
G = +2, Vo = 0.2Vpp
G = +2, Vo = 2Vpp
-8
DC, Vcm = 0V to Vs
RL = 10kΩ to Vs/2
RL = 1kΩ to Vs/2
RL = 200Ω to Vs/2
Output Current
Power Supply Operating Range
Max.
4.3
3.0
2.3
2.0
110
<1
9
-73
-75
0.03
22
1V step
1V step
1V step
1Vpp, 10kHz
1Vpp, 10kHz
1Vpp, 10kHz
>10kHz
DC
RL = 10kΩ
Typ.
40
1.5
15
90
40
60
80
160
Unit
MHz
MHz
MHz
MHz
ns
%
V/µs
dBc
dBc
%
nV/√Hz
+8
450
235
mV
µV/°C
nA
pA/°C
dB
dB
µA
12
2
-0.25 to 5.25
85
MΩ
pF
V
dB
0.08 to 4.92 0.04 to 4.96
0.07 to 4.9
0.14 to 4.67
±30
2.5
2.7
V
V
V
mA
V
58
5.5
Min/max ratings are based on product characterization and simulation. Individual parameters are tested as noted. Outgoing quality levels are
determined from tested parameters.
Notes:
1. For G = +1, Rf = 0.
2. For RL = 10kΩ, KM4170 is 100% tested at 25°C.
Package Thermal Resistance
Package
5 lead SOT23
5 lead SC70
8 lead SOIC
8 lead MSOP
14 lead TSSOP
4
θJA
256°C/W
331.4°C/W
152°C/W
206°C/W
100°C/W
REV. 5 December 2002
KM4170, KM4270, KM4470
DATA SHEET
Typical Operating Characteristics
(Vs = +2.7V, G = 2, RL = 10kΩ to Vs/2, Rf = 5kΩ; unless otherwise noted)
Inverting Frequency Response Vs = +5V
Normalized Magnitude (1dB/div)
Normalized Magnitude (1dB/div)
Non-Inverting Freq. Response Vs = +5V
Vo = 0.2Vpp
G=1
Rf = 0
G=2
Rf = 5kΩ
G = 10
Rf = 5kΩ
G=5
Rf = 5kΩ
0.01
0.1
1
Vo = 0.2Vpp
G = -2
Rf = 5kΩ
G = -10
Rf = 5kΩ
G = -5
Rf = 5kΩ
0.01
10
0.1
Frequency (MHz)
Normalized Magnitude (1dB/div)
Normalized Magnitude (1dB/div)
G = 10
Rf = 5kΩ
G=5
Rf = 5kΩ
0.01
0.1
10
Inverting Frequency Response
G=1
Rf = 0
G=2
Rf = 5kΩ
1
Frequency (MHz)
Non-Inverting Frequency Response
Vo = 0.2Vpp
G = -1
Rf = 5kΩ
1
Rf = 5kΩ
G = -2
G = -1
G = -10
G = -5
0.01
10
0.1
1
10
Frequency (MHz)
Frequency (MHz)
Frequency Response vs. CL
Frequency Response vs. RL
CL = 100pF
Rs = 100Ω
CL = 50pF
Rs = 0Ω
Magnitude (1dB/div)
Magnitude (1dB/div)
Vo = 0.05V
CL = 20pF
Rs = 0
CL = 10pF
Rs = 0
+
Rs
-
CL
5kΩ
RL = 1kΩ
RL = 10kΩ
RL = 200Ω
RL = 50Ω
RL
5kΩ
0.01
0.1
1
0.01
10
0.1
Frequency (MHz)
1
10
Frequency (MHz)
Large Signal Frequency Response
Open Loop Gain & Phase vs. Frequency
140
Magnitude (1dB/div)
Vo = 4Vpp
Vo = 2Vpp
Open Loop Gain (dB)
120
Vo = 1Vpp
|Gain|
RL = 10kΩ
Vs = 5V
|Gain|
No load
100
80
60
0
40
-45
-90
20
0
Phase
RL = 10kΩ
Phase
No load
101
103
-135
-20
0.01
0.1
1
Frequency (MHz)
REV. 5 December 2002
10
Open Loop Phase (deg)
Vs = 5V
-180
100
102
104
105
106
107
108
Frequency (Hz)
5
DATA SHEET
KM4170, KM4270, KM4470
Typical Operating Characteristics
(Vs = +2.7V, G = 2, RL = 10kΩ to Vs/2, Rf = 5kΩ; unless otherwise noted)
2nd & 3rd Harmonic Distortion
2nd Harmonic Distortion vs. Vo
-20
-20
Vo = 1Vpp
-40
3rd
RL = 200Ω
3rd
RL = 1kΩ
2nd
RL = 200Ω
-30
Distortion (dB)
Distortion (dBc)
-30
3rd
RL = 10kΩ
-50
-60
-70
-80
2nd
RL = 1kΩ
2nd
RL = 10kΩ
-40
-50
50kHz
-60
50kHz
-70
10kHz, 20kHz
-80
-90
10kHz
-90
0
20
40
60
80
0.5
100
1
Frequency (kHz)
3rd Harmonic Distortion vs. Vo
2
2.5
CMRR
0
-10
-30
-20
50kHz
-40
-50
CMRR (dB)
Distortion (dB)
1.5
Output Amplitude (Vpp)
-20
100kHz
-60
20kHz
-70
-30
-40
-50
-60
-70
10kHz
-80
-80
-90
-90
0.5
1
1.5
2
10
2.5
100
Output Amplitude (Vpp)
1000
10000
100000
Frequency (Hz)
PSRR
Output Swing vs. Load
1.35
0
RL = 10kΩ
Output Voltage (0.27V/div)
-10
-20
PSRR (dB)
100kHz
-30
-40
-50
-60
-70
-80
-90
RL = 1kΩ
RL = 75Ω
0
RL = 100Ω
RL = 200Ω
RL = 75/100Ω
-1.35
10
100
1000
10000
-2.0
100000
Frequency (Hz)
0
2.0
Input Voltage (0.4V/div)
Input Voltage Noise
Pulse Resp. vs. Common Mode Voltage
50
1.2V offset
45
0.6V offset
40
35
No offset
-0.6V offset
-1.2V offset
nV/√Hz
Output Voltage (0.5V/div)
55
30
25
20
15
10
5
0
Time (1µs/div)
0.1k
1k
10k
100k
1M
Frequency (Hz)
6
REV. 5 December 2002
KM4170, KM4270, KM4470
DATA SHEET
Application Information
Overdrive Recovery
General Description
Overdrive of an amplifier occurs when the output and/or
input ranges are exceeded. The recovery time varies based on
whether the input or output is overdriven and by how much
the ranges are exceeded. The KM4X70 will typically recover
in less than 50ns from an overdrive condition. Figure 3 shows
the KM4X70 amplifier family in an overdriven condition.
The KM4X70 family of amplifiers are single supply, general
purpose, voltage-feedback amplifiers. They are fabricated on
a complementary bipolar process, feature a rail-to-rail input
and output, and are unity gain stable.
The typical non-inverting circuit schematic is shown in Figure 1.
6.8µF
+
R11
R2
In
+
0.01µF
Out
KM4100
R12
-
Output
Input Voltage (0.5V/div)
+Vs
G=5
Input
Rout
Time (10µs/div)
Rf
Figure 3: Overdrive Recovery
Rg
Driving Capacitive Loads
Figure 1: Typical Non-inverting Configuration
Input Common Mode Voltage
The common mode input range extends to 250mV below
ground and to 250mV above Vs, in single supply operation.
Exceeding these values will not cause phase reversal. However,
if the input voltage exceeds the rails by more than 0.5V, the
input ESD devices will begin to conduct. The output will
stay at the rail during this overdrive condition. If the absolute
maximum input voltage (700mV beyond either rail) is
exceeded, externally limit the input current to ±5mA as
shown in Figure 2.
The Frequency Response vs. CL plot, illustrates the response
of the KM4X70 amplifier family. A small series resistance
(Rs) at the output of the amplifier, illustrated in Figure 4, will
improve stability and settling performance. Rs values in the
Frequency Response vs. CL plot were chosen to achieve maximum
bandwidth with less than 2dB of peaking. For maximum
flatness, use a larger Rs. Capacitive loads larger than 50pF
require the use of Rs.
+
Rs
Rf
Vin
RL
Rg
Vo
+
10kΩ
Figure 2: Circuit for Input Current Protection
Power Dissipation
The maximum internal power dissipation allowed is directly
related to the maximum junction temperature. If the maximum
junction temperature exceeds 150°C, some performance
degradation will occur. If the maximum junction temperature
exceeds 175°C for an extended time, device failure may occur.
REV. 5 December 2002
CL
Figure 4: Typical Topology for driving
a capacitive load
Driving a capacitive load introduces phase-lag into the output
signal, which reduces phase margin in the amplifier. The
unity gain follower is the most sensitive configuration. In a
unity gain follower configuration, the KM4X70 amplifier
family requires a 510Ω series resistor to drive a 100pF load.
7
DATA SHEET
KM4170, KM4270, KM4470
Layout Considerations
General layout and supply bypassing play major roles in high
frequency performance. Fairchild has evaluation boards to
use as a guide for high frequency layout and as aid in device
testing and characterization. Follow the steps below as a
basis for high frequency layout:
• Include 6.8µF and 0.01µF ceramic capacitors
• Place the 6.8µF capacitor within 0.75 inches of
the power pin
• Place the 0.01µF capacitor within 0.1 inches of
the power pin
• Remove the ground plane under and around the
part, especially near the input and output pins to
reduce parasitic capacitance
• Minimize all trace lengths to reduce series
inductances
Refer to the evaluation board layouts shown in Figure 6 for
more information.
When evaluating only one channel, complete the
following on the unused channel:
1. Ground the non-inverting input
2. Short the output to the inverting input
Figure 5a: KM4170 Evaluation Board Schematic
Evaluation Board Information
The following evaluation boards are available to aid in the
testing and layout of this device:
Eval Bd
Description
Products
KEB002
Single Channel, Dual Supply,
5 and 6 lead SOT23
KM4170IT5
KEB011
Single Channel, Dual Supply,
5 and 6 lead SC70
KM4170IS5
KEB006
Dual Channel, Dual Supply,
8 lead SOIC
KM4270IC8
KEB010
Dual Channel, Dual Supply,
8 lead MSOP
KM4270IM8
KEB012
Quad Channel, Dual Supply,
14 lead TSSOP
KM4470IP14
Evaluation board schematics are shown in Figures 5a, 5b, 5c
and layouts are shown in Figure 6a through Figure 6l.
Figure 5b: KM4270 Evaluation Board Schematic
8
REV. 5 December 2002
KM4170, KM4270, KM4470
DATA SHEET
Figure 5c: KM4470 Evaluation Board Schematic
REV. 5 December 2002
9
DATA SHEET
KM4170, KM4270, KM4470
KM4170 Evaluation Board Layout
10
Figure 6a: KEB002 (top side)
Figure 6b: KEB002 (bottom side)
Figure 6c: KEB011 (top side)
Figure 6d: KEB011 (bottom side)
REV. 5 December 2002
KM4170, KM4270, KM4470
DATA SHEET
KM4270 Evaluation Board Layout
Figure 6e: KEB006 (top side)
Figure 6f: KEB006 (bottom side)
Figure 6g: KEB010 (top side)
Figure 6h: KEB010 (bottom side)
REV. 5 December 2002
11
DATA SHEET
KM4170, KM4270, KM4470
KM4470 Evaluation Board Layout
12
Figure 6i: KEB012 (top side)
Figure 6j: KEB012 (bottom side)
Figure 6k: KEB012 (layer1 mask)
Figure 6l: KEB012 (layer2 mask)
REV. 5 December 2002
KM4170, KM4270, KM4470
DATA SHEET
b
SOT23-5
CL
DATUM ’A’
KM4170 Package Dimensions
e
2
CL
CL
E
e1
α
C
D
CL
A
e
L
SC70
CL
CL
HE
E
Q1
CL
REV. 5 December 2002
A2
SYMBOL
e
D
b
E
HE
Q1
A2
A1
A
c
L
MIN
MAX
0.65 BSC
1.80
2.20
0.15
0.30
1.15
1.35
1.80
2.40
0.10
0.40
0.80
1.00
0.00
0.10
0.80
1.10
0.10
0.18
1.10
0.30
C
D
A
MAX
1.45
0.15
1.30
0.50
0.20
3.10
3.00
1.75
0.55
0.95 ref
1.90 ref
0
10
1. All dimensions are in millimeters.
2 Foot length measured reference to flat
foot surface parallel to DATUM ’A’ and lead surface.
3. Package outline exclusive of mold flash & metal burr.
4. Package outline inclusive of solder plating.
5. Comply to EIAJ SC74A.
6. Package ST 0003 REV A supercedes SOT-D-2005 REV C.
A1
CL
MIN
0.90
0.00
0.90
0.25
0.09
2.80
2.60
1.50
0.35
NOTE:
A2
b
E1
SYMBOL
A
A1
A2
b
C
D
E
E1
L
e
e1
α
NOTE:
A1
1.
2.
3.
4.
All dimensions are in millimeters.
Dimensions are inclusive of plating.
Dimensions are exclusive of mold flashing and metal burr.
All speccifications comply to EIAJ SC70.
13
DATA SHEET
KM4170, KM4270, KM4470
KM4270 Package Dimensions
SOIC-8
SOIC
D
SYMBOL
A1
B
C
D
E
e
H
h
L
A
7°
e
ZD
CL
CL
Pin No. 1
E
H
B
ZD
A2
DETAIL-A
L
NOTE:
h x 45°
A
A1
DETAIL-A
1. All dimensions are in millimeters.
2. Lead coplanarity should be 0 to 0.10mm (.004") max.
3. Package surface finishing:
(2.1) Top: matte (charmilles #18~30).
(2.2) All sides: matte (charmilles #18~30).
(2.3) Bottom: smooth or matte (charmilles #18~30).
4. All dimensions excluding mold flashes and end flash
from the package body shall not exceed o.152mm (.006)
per side(d).
α
A2
C
e
MSOP
02
S
MSOP-8
t1
R1
t2
E/2 2X
–H–
R
Gauge
Plane
E1 3 7
0.25mm
–B–
L1
b
ccc A B C
2
01
L
03
2
E3
E4
1
c
Detail A
Scale 40:1
c1
2
4
6
–C–
D2
A2
A1
A
Detail A
E1
E
D
3
E2
A
–A–
b
bbb M A B C
b1
Section A - A
5
A
aaa A
4
NOTE:
1 All dimensions are in millimeters (angle in degrees), unless otherwise specified.
14
MIN
MAX
0.10
0.25
0.36
0.46
0.19
0.25
4.80
4.98
3.81
3.99
1.27 BSC
5.80
6.20
0.25
0.50
0.41
1.27
1.52
1.72
8
0
0.53 ref
1.37
1.57
2
Datums – B – and – C – to be determined at datum plane – H – .
3
Dimensions "D" and "E1" are to be determined at datum – H – .
4
Dimensions "D2" and "E2" are for top package and dimensions "D" and "E1" are for bottom package.
5
Cross sections A – A to be determined at 0.13 to 0.25mm from the leadtip.
6
Dimension "D" and "D2" does not include mold flash, protrusion or gate burrs.
7
Dimension "E1" and "E2" does not include interlead flash or protrusion.
SYMBOL
MIN
A
1.10
A1
0.10
A2
0.86
D
3.00
D2
2.95
E
4.90
E1
3.00
E2
2.95
E3
0.51
E4
0.51
R
0.15
R1
0.15
t1
0.31
t2
0.41
b
0.33
b1
0.30
c
0.18
c1
0.15
01
3.0°
02
12.0°
03
12.0°
L
0.55
L1
0.95 BSC
aaa
0.10
bbb
0.08
ccc
0.25
e
0.65 BSC
S
0.525 BSC
MAX
–
±0.05
±0.08
±0.10
±0.10
±0.15
±0.10
±0.10
±0.13
±0.13
+0.15/-0.06
+0.15/-0.06
±0.08
±0.08
+0.07/-0.08
±0.05
±0.05
+0.03/-0.02
±3.0°
±3.0°
±3.0°
±0.15
–
–
–
–
–
–
REV. 5 December 2002
KM4170, KM4270, KM4470
DATA SHEET
KM4470 Package Dimensions
TSSOP
6
e
–B–
7
N
5
(b)
2X E/2
1.0 DIA
TSSOP-14
8
E1 E
c
c1
1.0
b1
ddd C B A
2X
N/2 TIPS
1 2 3
6
SECTION AA
e /2 9
1.0
ccc
7
–A–
A2
D 8 3
aaa C
A
–C–
b NX
A1
(02)
(0.20)
bbb M C B A
R1
–H–
R
GAGE
PLANE
10
A
0.25
(03)
A
L
(L1)
01
SYMBOL
A
A1
A2
L
R
R1
b
b1
c
c1
01
L1
aaa
bbb
ccc
ddd
e
02
03
D
E1
E
e
N
MIN
–
0.05
0.85
0.50
0.09
0.09
0.19
0.19
0.09
0.09
0°
4.90
4.30
NOM
–
–
0.90
0.60
–
–
–
0.22
–
–
–
1.0 REF
0.10
0.10
0.05
0.20
0.65 BSC
12° REF
12° REF
5.00
4.40
6.4 BSC
0.65 BSC
14
MAX
1.10
0.15
0.95
0.75
–
–
0.30
0.25
0.20
0.16
8°
5.10
4.50
NOTES:
1 All dimensions are in millimeters (angle in degrees).
2
Dimensioning and tolerancing per ASME Y14.5–1994.
3
Dimensions "D" does not include mold flash, protusions or gate burrs. Mold flash protusions or gate burrs shall not exceed 0.15 per side .
4
Dimension "E1" does not include interlead flash or protusion. Interlead flash or protusion shall not exceed 0.25 per side.
5
Dimension "b" does not include dambar protusion. Allowable dambar protusion shall be 0.08mm total in excess of the "b" dimension at maximum
material condition. Dambar connot be located on the lower radius of the foot. Minimum space between protusion and adjacent lead is 0.07mm
for 0.5mm pitch packages.
6
Terminal numbers are shown for reference only.
7
Datums – A – and – B – to be determined at datum plane – H – .
8
Dimensions "D" and "E1" to be determined at datum plane – H – .
9
This dimensions applies only to variations with an even number of leads per side. For variation with an odd number of leads per side, the "center"
lead must be coincident with the package centerline, Datum A.
10
Cross sections A – A to be determined at 0.10 to 0.25mm from the leadtip.
REV. 5 December 2002
15
DATA SHEET
KM4170, KM4270, KM4470
Ordering Information
Model
Part Number
Package
Container
Pack Qty
KM4170
KM4170IT5TR3
SOT23-5
Reel
3000
KM4170
KM4170IS5TR3
SC70-5
Reel
3000
KM4270
KM4270IC8TR3
SOIC-8
Reel
2500
KM4270
KM4270IM8TR3
MSOP-8
Reel
3000
KM4470
KM4470IP14TR3 TSSOP-14
Reel
2500
Temperature range for all parts: -40°C to +85°C.
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICES TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR
DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY
ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF
THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein:
1.
Life support devices or systems are devices or systems which, (a) are intended for
surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform
when properly used in accordance with instructions for use provided in the labeling, can
be reasonably expected to result in a significant injury of the user.
www.fairchildsemi.com
2.
A critical component in any component of a life support device or system whose failure
to perform can be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or effectiveness.
© 2001 Fairchild Semiconductor Corporation