STMicroelectronics L79L05ACD13TR Negative voltage regulator Datasheet

L79L
Negative voltage regulators
Datasheet - production data
Description
The L79L series of three-terminal negative
regulators employ internal current limiting and
thermal shutdown, making them essentially
indestructible. If adequate heat-sink is provided,
they can deliver up to 100 mA output current.
They are intended as fixed voltage regulators in a
wide range of applications including local or oncard regulation for elimination of noise and
distribution problems associated with single-point
regulation. In addition, they can be used with
power pass elements to make high-current
voltage regulators. The L79L series used as
Zener diode/resistor combination replacement,
offers an effective output impedance
improvement of typically two orders of magnitude,
along with lower quiescent current and lower
noise.
Features






Output current up to 100 mA
Output voltages of -5; -8;-12; -15 V
Thermal overload protection
Short-circuit protection
No external components are required
Available in ±5% (AC) or ± 10% (C)
selection
February 2016
DocID2511 Rev 18
This is information on a product in full production.
1/24
www.st.com
Contents
L79L
Contents
1
Diagram ............................................................................................ 3
2
Pin configuration ............................................................................. 4
3
Maximum ratings ............................................................................. 5
4
5
Electrical characteristics ................................................................ 6
Package information ..................................................................... 10
5.1
TO-92 package information ............................................................. 10
5.2
TO-92 packing information .............................................................. 11
5.3
TO-92 Ammopak package information ............................................ 13
5.4
SO-8 package information .............................................................. 15
5.5
SO-8 packing information ................................................................ 17
5.6
SOT-89 package information .......................................................... 18
5.7
SOT-89 packing information............................................................ 21
6
Ordering information..................................................................... 22
7
Revision history ............................................................................ 23
2/24
DocID2511 Rev 18
L79L
1
Diagram
Diagram
Figure 1: Schematic diagram
DocID2511 Rev 18
3/24
Pin configuration
2
L79L
Pin configuration
Figure 2: Pin connection (top view, bottom view for TO-92)
Figure 3: Test circuit
4/24
DocID2511 Rev 18
L79L
3
Maximum ratings
Maximum ratings
Table 1: Absolute maximum ratings
Symbol
Parameter
VI
DC input voltage
IO
Output current
PD
Value
Unit
VO = -5 to -9 V
-30
VO = -12 to -15 V
-35
V
100
mA
Internally limited
Power dissipation
TSTG
Storage temperature range
TOP
Operating junction temperature range
(1)
-40 to 150
For L79LXXAC
0 to 125
For L79LXXAB
-40 to 125
mW
°C
°C
Notes:
(1)
Our SO-8 package used for Voltage Regulators is modified internally to have pins 2, 3, 6 and 7 electrically
communed to the die attach flag. This particular frame decreases the total thermal resistance of the package and
increases its ability to dissipate power when an appropriate area of copper on the printed circuit board is available
for heat-sinking. The external dimensions are the same as for the standard SO-8.
Table 2: Thermal data
Symbol
RthJC
RthJA
Parameter
Thermal resistance junction-case (Max)
Thermal resistance junction-ambient (Max)
SO-8
TO-92
20
55
(1)
200
SOT-89
Unit
15
°C/W
115
°C/W
Notes:
(1)
Considering 6 cm2 of copper Board heat-sink.
DocID2511 Rev 18
5/24
Electrical characteristics
4
L79L
Electrical characteristics
Refer to the test circuits, VI = - 10 V, IO = 40 mA, CI = 0.33 μF, CO = 0.1 μF, TJ = 0 to
125 °C for L79L05AC, TJ = -40 to 125 °C for L79L05AB, unless otherwise specified.
Table 3: Electrical characteristics of L79L05AC and L79L05AB
Symbol
6/24
Parameter
VO
Output voltage
VO
Output voltage
∆VO
Line regulation
∆VO
Load regulation
Test conditions
Min.
Typ.
Max.
Unit
TJ = 25 °C
-4.8
-5
-5.2
V
IO = 1 to 40 mA, VI = -7 to -20 V
-4.75
-5.25
IO = 1 to 70 mA, VI = -10 V
-4.75
-5.25
V
VI = -7 to -20 V, TJ = 25 °C
150
VI = -8 to -20 V, TJ = 25 °C
100
IO = 1 to 100 mA, TJ = 25 °C
60
IO = 1 to 40 mA, TJ = 25 °C
30
TJ = 25 °C
6
mA
TJ = 125 °C
5.5
mA
Id
Quiescent current
∆Id
Quiescent current
change
IO = 1 to 40 mA
0.1
VI = -8 to -20 V
1.5
eN
Output noise voltage
B = 10 Hz to 100 kHz, TJ = 25 °C
SVR
Supply voltage
rejection
VI = -8 to -18 V, f = 120 Hz
IO = 40 mA, TJ = 25 °C
Vd
Dropout voltage
DocID2511 Rev 18
41
mV
mV
mA
40
µV
49
dB
1.7
V
L79L
Electrical characteristics
Refer to the test circuits, VI = - 14 V, IO = 40 mA, CI = 0.33 μF, CO = 0.1 μF, TJ = 0 to
125 °C for L79L08AC TJ = -40 to 125 °C for L79L08AB, unless otherwise specified.
Table 4: Electrical characteristics of L79L08AC and L79L08AB
Symbol
Parameter
VO
Output voltage
VO
Output voltage
∆VO
Line regulation
∆VO
Load regulation
Test conditions
Min.
Typ.
Max.
Unit
TJ = 25 °C
-7.68
-8
-8.32
V
IO = 1 to 40 mA, VI = -10.5 to -23 V
-7.6
-8.4
IO = 1 to 70 mA, VI = -14 V
-7.6
-8.4
V
VI = -10.5 to -23 V, TJ = 25 °C
175
VI = -11 to -23 V, TJ = 25 °C
125
IO = 1 to 100 mA, TJ = 25 °C
80
IO = 1 to 40 mA, TJ = 25 °C
40
TJ = 25 °C
6
mA
TJ = 125 °C
5.5
mA
IO = 1 to 40 mA
0.1
VI = -11 to -23 V
1.5
Id
Quiescent current
∆Id
Quiescent current
change
eN
Output noise
voltage
B = 10 Hz to 100 kHz, TJ = 25 °C
SVR
Supply voltage
rejection
VI = -12 to -23 V, f = 120 Hz,
IO = 40 mA, TJ = 25 °C
Vd
Dropout voltage
DocID2511 Rev 18
37
mV
mV
mA
60
µV
45
dB
1.7
V
7/24
Electrical characteristics
L79L
Refer to the test circuits, VI = - 19 V, IO = 40 mA, CI = 0.33 μF, CO = 0.1 μF, TJ = 0 to
125 °C for L79L12AC, TJ = -40 to 125 °C for L79L12AB, unless otherwise specified.
Table 5: Electrical characteristics of L79L12AC and L79L12AB
Symbol
8/24
Parameter
VO
Output voltage
VO
Output voltage
∆VO
Line regulation
∆VO
Load regulation
Test conditions
Min.
Typ.
Max.
Unit
TJ = 25°C
-11.5
-12
-12.5
V
IO = 1 to 40 mA, VI = -14.5 to -27 V
-11.4
-12.6
IO = 1 to 70 mA, VI = -19 V
-11.4
-12.6
V
VI = -14.5 to -27 V, TJ = 25 °C
250
VI = -16 to -27 V, TJ = 25 °C
200
IO = 1 to 100 mA, TJ = 25 °C
100
IO = 1 to 40 mA, TJ = 25 °C
50
TJ = 25 °C
6.5
mA
TJ = 125 °C
6
mA
Id
Quiescent current
∆Id
Quiescent current
change
eN
Output noise
voltage
B = 10 Hz to 100 kHz, TJ = 25 °C
SVR
Supply voltage
rejection
VI = -15 to -25 V, f = 120 Hz
IO = 40 mA, TJ = 25 °C
Vd
Dropout voltage
IO = 1 to 40 mA
0.1
VI = -16 to -27 V
1.5
DocID2511 Rev 18
37
mV
mV
mA
80
µV
42
dB
1.7
V
L79L
Electrical characteristics
Refer to the test circuits, VI = - 23 V, IO = 40 mA, CI = 0.33 μF, CO = 0.1 μF, TJ = 0 to
125 °C for L79L15AC, TJ = -40 to 125 °C for L79L15AB, unless otherwise specified.
Table 6: Electrical characteristics of L79L15AC and L79L15AB
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
-15
-15.6
V
VO
Output voltage
TJ = 25°C
-14.4
VO
Output voltage
IO = 1 to 40 mA,
VI = -17.5 to -30 V
-14.25
-15.75
IO = 1 to 70 mA, VI = -23 V
-14.25
-15.75
∆VO
Line regulation
∆VO
Load regulation
V
VI = -17.5 to -30 V, TJ = 25 °C
300
VI = -20 to -30 V, TJ = 25 °C
250
IO = 1 to 100 mA, TJ = 25 °C
150
IO = 1 to 40 mA, TJ = 25 °C
75
TJ = 25 °C
6.5
mA
TJ = 125 °C
6
mA
Id
Quiescent current
∆Id
Quiescent current
change
IO = 1 to 40 mA
0.1
VI = -20 to -30 V
1.5
eN
Output noise
voltage
B = 10 Hz to 100 kHz,
TJ = 25 °C
SVR
Supply voltage
rejection
VI = -18.5 to -28.5.V, f = 120 Hz
IO = 40 mA, TJ = 25 °C
Vd
Dropout voltage
DocID2511 Rev 18
34
mV
mV
mA
90
µV
39
dB
1.7
V
9/24
Package information
5
L79L
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK ®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
5.1
TO-92 package information
Figure 4: TO-92 package outline
Table 7: TO-92 mechanical data
mm
Dim.
Min.
Max.
A
4.32
4.95
b
0.36
0.51
D
4.45
4.95
E
3.30
3.94
e
2.41
2.67
e1
1.14
1.40
L
12.70
15.49
R
2.16
2.41
S1
0.92
1.52
W
0.41
0.56
V
10/24
Typ.
5°
DocID2511 Rev 18
L79L
5.2
Package information
TO-92 packing information
Figure 5: TO-92 tape and reel outline
DocID2511 Rev 18
11/24
Package information
L79L
Table 8: TO-92 tape and reel mechanical data
mm
Dim.
Min.
Typ.
A1
4.80
T
3.80
T1
1.60
T2
2.30
d
0.45
0.47
0.48
P0
12.50
12.70
12.90
P2
5.65
6.35
7.05
F1, F2
2.40
2.50
2.94
F3
4.98
5.08
5.48
delta H
-2.00
W
17.50
18.00
19.00
W0
5.5
6.00
6.5
W1
8.50
9.00
9.25
2.00
W2
0.50
H
18.50
21
H3
0.5
1
2
H0
15.50
16.00
18.8
25.0
27.0
4.00
4.20
H1
D0
12/24
Max.
3.80
t
0.90
L
11.00
I1
3.00
delta P
-1.00
Ø1
352
355
358
Ø2
28
30
32
u
44
47
50
DocID2511 Rev 18
1.00
L79L
5.3
Package information
TO-92 Ammopak package information
Figure 6: TO-92 Ammopak tape and reel outline
DocID2511 Rev 18
13/24
Package information
L79L
Table 9: TO-92 Ammopak tape and reel mechanical data
mm
Dim.
Min.
Typ.
A1
4.80
T
3.80
T1
1.60
T2
2.30
d
0.45
0.47
0.48
P0
12.50
12.70
12.90
P2
5.65
6.35
7.05
F1, F2
2.40
2.50
2.94
F3
4.98
5.08
5.48
delta H
-2.00
W
17.50
18.00
19.00
W0
5.5
6.00
6.5
W1
8.50
9.00
9.25
2.00
W2
0.50
H
18.50
21
H3
0.5
1
2
H0
15.50
16.00
18.8
25.0
27.0
4.00
4.20
H1
D0
14/24
Max.
3.80
t
0.90
L
11.00
I1
3.00
delta P
-1.00
DocID2511 Rev 18
1.00
L79L
5.4
Package information
SO-8 package information
Figure 7: SO-8 package outline
DocID2511 Rev 18
15/24
Package information
L79L
Table 10: SO-8 mechanical data
mm
Dim.
Min.
Typ.
A
1.75
A1
0.10
A2
1.25
b
0.31
0.51
b1
0.28
0.48
0.25
c
0.10
0.25
c1
0.10
0.23
D
4.80
4.90
5.00
E
5.80
6.00
6.20
E1
3.80
3.90
4.00
e
1.27
h
0.25
0.50
L
0.40
1.27
L1
1.04
L2
0.25
k
0°
ccc
8°
0.10
Figure 8: SO-8 recommended footprint (dimensions are in mm)
16/24
Max.
DocID2511 Rev 18
L79L
5.5
Package information
SO-8 packing information
Figure 9: SO-8 tape and reel dimensions
Table 11: SO-8 tape and reel mechanical data
Dim.
mm
Min.
A
Typ.
Max.
330
C
12.8
D
20.2
N
60
T
13.2
22.4
Ao
8.1
8.5
Bo
5.5
5.9
Ko
2.1
2.3
Po
3.9
4.1
P
7.9
8.1
DocID2511 Rev 18
17/24
Package information
5.6
L79L
SOT-89 package information
Figure 10: SOT-89 package outline
18/24
DocID2511 Rev 18
L79L
Package information
Table 12: SOT-89 mechanical data
mm
Dim.
Min.
Typ.
Max.
A
1.40
1.60
B
0.44
0.56
B1
0.36
0.48
C
0.35
0.44
C1
0.35
0.44
D
4.40
4.60
D1
1.62
1.83
D3
0.90
E
2.29
2.60
e
1.42
1.57
e1
2.92
3.07
H
3.94
4.25
H1
2.70
3.10
K
1°
8°
L
0.89
120
R
0.25
β
90°
DocID2511 Rev 18
19/24
Package information
L79L
Figure 11: SOT-89 recommended footprint
20/24
DocID2511 Rev 18
L79L
5.7
Package information
SOT-89 packing information
Figure 12: SOT-89 carrier tape outline
Table 13: SOT-89 carrier tape mechanical data
mm
Dim.
Value
Tolerance
Ao
4.91
± 0.10
Bo
4.52
± 0.10
Ko
1.90
± 0.10
F
5.50
± 0.10
E
1.75
± 0.10
W
12
± 0.30
P2
2
± 0.10
Po
4
± 0.10
P1
8
± 0.10
T
0.30
± 0.10
D
Ø 1.55
± 0.05
D1
Ø 1.60
± 0.10
DocID2511 Rev 18
21/24
Ordering information
6
L79L
Ordering information
Table 14: Order codes
SO-8
TO-92
(bag)
TO-92
(Ammopak)
L79L05ABD13TR
L79L05ACZ
L79L05ABZ-AP
L79L05ACD13TR
L79L08ACZ-AP
TO-92
(tape and reel)
L79L05ACZ-TR
SOT-89
Output
voltage
(V)
L79L05ABUTR
-5
L79L05ACUTR
-5
L79L08ACD13TR
-8
L79L12ACD13TR
L79L12ACZ-TR
L79L12ACUTR
L79L15ABD13TR
-15
L79L15ACD13TR
22/24
-12
L79L15ACUTR
DocID2511 Rev 18
-15
L79L
7
Revision history
Revision history
Table 15: Document revision history
Date
Revision
Changes
14-Mar-2005
9
Add Tape and Reel for TO-92.
15-Mar-2005
10
Add note on Table 3.
23-Dec-2005
11
Mistake on ordering Table in Header.
12-Sep-2006
12
Order codes updated.
25-Jul-2007
13
Pin connection for SOT-89 updated on Figure 2.
04-Dec-2007
14
Modified: Table 14.
14-Jul-2008
15
Modified: Table 14 on page 24.
29-Jul-2009
16
Modified: Table 14 on page 24.
17-Apr-2014
17
Part numbers L79LxxAB, L78LxxAC, L78LxxC
changed to L79L. Removed Table 1: Device summary.
Updated the features and description in cover page.
Updated Figure 1: Schematic diagram, Table 1:
Absolute maximum ratings and Table 14: Order codes.
Added Section 5: Packaging mechanical data. Minor
text changes.
12-Feb-2016
18
Updated Section 5: Package information.
Minor text changes.
DocID2511 Rev 18
23/24
L79L
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST
products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the
design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2016 STMicroelectronics – All rights reserved
24/24
DocID2511 Rev 18
Similar pages