SMSC LAN91C111I-NS 10/100 non-pci ethernet single chip mac phy Datasheet

LAN91C111
10/100 Non-PCI
Ethernet Single Chip
MAC + PHY
PRODUCT FEATURES
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
Datasheet
Single Chip Ethernet Controller
Dual Speed - 10/100 Mbps
Fully Supports Full Duplex Switched Ethernet
Supports Burst Data Transfer
8 Kbytes Internal Memory for Receive and Transmit
FIFO Buffers
Enhanced Power Management Features
Optional Configuration via Serial EEPROM Interface
Supports 8, 16 and 32 Bit CPU Accesses
Internal 32 Bit Wide Data Path (Into Packet Buffer
Memory)
Early TX, Early RX Functions
Built-in Transparent Arbitration for Slave Sequential
Access Architecture
Flat MMU Architecture with Symmetric Transmit and
Receive Structures and Queues
3.3V Operation with 5V Tolerant IO Buffers (See Pin
List Description for Additional Details)
Single 25 MHz Reference Clock for Both PHY and
MAC
External 25Mhz-output pin for an external PHY
supporting PHYs physical media.
Low Power CMOS Design
Supports Multiple Embedded Processor Host
Interfaces
—
—
—
—
—
—
■
■
■
■
■
3.3V MII (Media Independent Interface) MAC-PHY
Interface Running at Nibble Rate
MII Management Serial Interface
128 Pin QFP package; green, lead-free package also
available.
128 Pin TQFP package, 1.0 mm height; green, leadfree package also available.
Industrial Temperature Range from -40°C to 85°C
(LAN91C111i only)
Network Interface
■ Fully Integrated IEEE 802.3/802.3u-100Base-TX/
10Base-T Physical Layer
■ Auto Negotiation: 10/100, Full / Half Duplex
■ On Chip Wave Shaping - No External Filters
Required
■ Adaptive Equalizer
■ Baseline Wander Correction
■ LED Outputs (User selectable – Up to 2 LED
functions at one time)
—
—
—
—
—
—
Link
Activity
Full Duplex
10/100
Transmit
Receive
ARM
SH
Power PC
Coldfire
680X0, 683XX
MIPS R3000
SMSC LAN91C111-REV B
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
ORDER NUMBER(S):
LAN91C111-NC, LAN91C111i-NC (INDUSTRIAL TEMPERATURE)
FOR 128 PIN QFP PACKAGES
LAN91C111-NS, LAN91C111i-NS (INDUSTRIAL TEMPERATURE)
FOR 128 PIN QFP PACKAGES (GREEN, LEAD-FREE)
LAN91C111-NE (1.0MM HEIGHT); LAN91C111i-NE (INDUSTRIAL TEMPERATURE)
FOR 128 PIN TQFP PACKAGES
LAN91C111-NU (1.0MM HEIGHT); LAN91C111i-NU (INDUSTRIAL TEMPERATURE)
FOR 128 PIN TQFP PACKAGES (GREEN, LEAD-FREE)
80 Arkay Drive
Hauppauge, NY 11788
(631) 435-6000
FAX (631) 273-3123
Copyright © 2005 SMSC or its subsidiaries. All rights reserved.
Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently,
complete information sufficient for construction purposes is not necessarily given. Although the information has been checked and is believed to be
accurate, no responsibility is assumed for inaccuracies. SMSC reserves the right to make changes to specifications and product descriptions at any
time without notice. Contact your local SMSC sales office to obtain the latest specifications before placing your product order. The provision of this
information does not convey to the purchaser of the described semiconductor devices any licenses under any patent rights or other intellectual
property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated
version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may
contain design defects or errors known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly
sheets are available upon request. SMSC products are not designed, intended, authorized or warranted for use in any life support or other
application where product failure could cause or contribute to personal injury or severe property damage. Any and all such uses without prior written
approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of this document or other
SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC’s website at http://www.smsc.com. SMSC is a
registered trademark of Standard Microsystems Corporation (“SMSC”). Product names and company names are the trademarks of their respective
holders.
SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE,
AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE OF DEALING OR USAGE OF TRADE.
IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL
DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION,
WHETHER BASED ON CONTRACT; TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR
OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS HELD TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER
OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Revision 1.8 (07-13-05)
2
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
0.1
Datasheet Revision History
Table 0.1 LAN91C111 Datasheet Revision History
NAME
REVISION
LEVEL AND
DATE
K. Lawrence
SMSC LAN91C111-REV B
SECTION/FIGURE/ENTRY
CORRECTION
Rev. 1.8
(07-13-05)
Chapter 14, "Timing
Diagrams," on page 125 (Figure 14.1, Figure 14.2, and
Figure 14.3), and Chapter 8,
MAC Data Structures and
Registers
Fixed t4 MIN/MAX values. Clarified CRC
in RX packet description.
Rev. 1.7
(11-16-04)
Ordering Information
Lead-free added.
Rev. 1.6
(05-18-04)
Chapter 14, "Timing
Diagrams," on page 125 (Figure 14.1, Figure 14.2, and
Figure 14.3)
Modified t1 and t4.
Rev. 1.6
(05-18-04)
Table 10.2, “Flow Of Events
For Restoring Device In
Normal Power Mode,” on
page 96
Modified description of restoring to normal
power mode.
Rev. 1.6
(05-18-04)
Section 7.7.17, "PHY
Powerdown," on page 50
Modified description of PHY power down
mode.
Rev. 1.5
(02-20-04)
Chapter 5, "Description of Pin
Functions," on page 23
Modified description of INTR0 pin active
high.
Rev. 1.5
(02-20-04)
Table 9.2, “MII Serial Port
Register MAP,” on page 84
Modified Reg.18 LNKFAIL bit to “0” by
default.
Rev. 1.4
(12-12-03)
Features
Removed “user programmable” under
LED Output features.
Rev. 1.3
(07-29-03)
Section 13.1, "Maximum
Guaranteed Ratings*," on
page 119
Modified LAN91C111 Temp 0°C to +85°C.
Rev. 1.3
(07-18-03)
Section 8.2, "Receive Frame
Status," on page 54
Modified description of the BROADCAST
bit in Receive Frame Status.
Rev. 1.3
(07-18-03)
Section 8.5, "Bank 0 Transmit Control Register," on
page 57
Modified description of the STP_SQET bit
in TCR Register.
Rev. 1.3
(07-18-03)
Section 8.6, "Bank 0 - EPH
Status Register," on page 58
Modified description of SQET bit in EPH
Status Register.
Rev. 1.2
(09-17-02)
Section 8.12, "Bank 1 - Base
Address Register," on
page 65
Added chart showing decoding of I/O
Base Address 300h.
Rev. 1.0
(07-01-02)
Chapter 5, "Description of Pin
Functions," on page 23
Add Buffer Type for nLEDA and nLEDB,
Add description of LCLK.
Rev. 1.0
(07-01-02)
Section 7.7.12, "Link Integrity
& Autonegotiation," on
page 46
Modified Auto-Negotiation Enable
Description.
Rev. 1.0
(07-01-02)
Section 7.8, "Reset," on
page 51
Add Reset Description.
3
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Table 0.1 LAN91C111 Datasheet Revision History (continued)
NAME
REVISION
LEVEL AND
DATE
SMSC LAN91C111-REV B
SECTION/FIGURE/ENTRY
CORRECTION
Rev. 1.0
(07-01-02)
Section 8.5, "Bank 0 Transmit Control Register," on
page 57
Add Description for FDUPLX bit.
Rev. 1.0
(07-01-02)
Section 8.10, "Bank 0 Receive/Phy Control
Register," on page 61
Add Description for SPEED, DPLX, ANEG
bits.
Rev. 1.0
(07-01-02)
Section 8.21, "Bank 2 Interrupt Status Registers," on
page 72
Add Description for Interrupt Status and
Mask bits.
Rev. 1.0
(07-01-02)
Figure 8.2 Interrupt
Structureon page 75
Modified Interrupt Structure Figure.
Rev. 1.0
(07-01-02)
Chapter 9, "PHY MII
Registers ," on page 81
Changed bit name 0 to Reserved.
Rev. 1.0
(07-01-02)
Section 9.10, "Register 20.
Reserved - Structure and Bit
Definition," on page 93
Reserved bits default at 00A0.
Rev. 1.0
(07-01-02)
Section 10.2, "Typical Flow of
Events for Transmit (Auto
Release = 0)," on page 96
Modified Typical Flow of Event for TX.
Rev. 1.0
(07-01-02)
Section 10.3, "Typical Flow of
Events for Transmit (Auto
Release = 1)," on page 97
Modified Typical Flow of Event for TX.
4
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Table of Contents
0.1
Datasheet Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Chapter 1 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Chapter 2 Pin Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Chapter 3 Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Chapter 4 Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Chapter 5 Description of Pin Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Chapter 6 Signal Description Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.1
Buffer Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Chapter 7 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
Clock Generator Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CSMA/CD Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.1
DMA Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.2
Arbiter Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MMU Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BIU Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAC-PHY Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.5.1
Management Data Software Implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.5.2
Management Data Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.5.3
MI Serial Port Frame Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.5.4
MII Packet Data Communication with External PHY . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial EEPROM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Internal Physical Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.7.1
MII Disable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.7.2
Encoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.7.3
Decoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.7.4
Clock and Data Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.7.5
Scrambler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.7.6
Descrambler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.7.7
Twisted Pair Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.7.8
Twisted Pair Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.7.9
Collision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.7.10 Start of Packet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.7.11 End of Packet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.7.12 Link Integrity & Autonegotiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.7.13 Jabber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.7.14 Receive Polarity Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.7.15 Full Duplex Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.7.16 Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.7.17 PHY Powerdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.7.18 PHY Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
29
29
29
29
29
30
30
30
31
31
33
34
34
36
36
36
38
38
38
39
42
44
44
45
46
49
49
50
50
50
50
51
Chapter 8 MAC Data Structures and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
8.1
8.2
Frame Format In Buffer Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Receive Frame Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
SMSC LAN91C111-REV B
5
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
8.3
8.4
8.5
8.6
8.7
8.8
8.9
8.10
8.11
8.12
8.13
8.14
8.15
8.16
8.17
8.18
8.19
8.20
8.21
8.22
8.23
8.24
8.25
8.26
I/O Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank Select Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank 0 - Transmit Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank 0 - EPH Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank 0 - Receive Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank 0 - Counter Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank 0 - Memory Information Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank 0 - Receive/Phy Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank 1 - Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank 1 - Base Address Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank 1 - Individual Address Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank 1 - General Purpose Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank 1 - Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank 2 - MMU Command Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank 2 - Packet Number Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank 2 - FIFO Ports Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank 2 - Pointer Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank 2 - Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank 2 - Interrupt Status Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank 3 - Multicast Table Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank 3 - Management Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank 3 - Revision Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank 3 - Early RCV Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank 7 - External Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
55
56
57
58
59
60
61
61
64
65
65
66
67
68
69
70
71
71
72
76
77
77
78
78
Chapter 9 PHY MII Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
9.9
9.10
Register 0. Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Register 1. Status Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Register 2&3. PHY Identifier Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Register 4. Auto-Negotiation Advertisement Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Register 5. Auto-Negotiation Remote End Capability Register . . . . . . . . . . . . . . . . . . . . . . . . . . .
Register 16. Configuration 1- Structure and Bit Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Register 17. Configuration 2 - Structure and Bit Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Register 18. Status Output - Structure and Bit Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Register 19. Mask - Structure and Bit Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Register 20. Reserved - Structure and Bit Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
85
86
87
87
88
89
90
91
92
93
Chapter 10 Software Driver and Hardware Sequence Flow . . . . . . . . . . . . . . . . . . . . . . . . . 95
10.1
10.2
10.3
10.4
Software Driver and Hardware Sequence Flow for Power Management . . . . . . . . . . . . . . . . . . . .
Typical Flow of Events for Transmit (Auto Release = 0). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Typical Flow of Events for Transmit (Auto Release = 1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Typical Flow of Event For Receive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
95
96
97
98
Chapter 11 Board Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Chapter 12 Application Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Chapter 13 Operational Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
13.1
13.2
13.3
13.4
Maximum Guaranteed Ratings* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Twisted Pair Characteristics, Transmit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Twisted Pair Characteristics, Receive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
119
119
122
123
Chapter 14 Timing Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Revision 1.8 (07-13-05)
6
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Chapter 15 Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
SMSC LAN91C111-REV B
7
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Revision 1.8 (07-13-05)
8
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
List of Figures
Figure 2.1 Pin Configuration - LAN91C111-FEAST 128 PIN TQFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 2.2 Pin Configuration - LAN91C111-FEAST 128 PIN QFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 3.1 Basic Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 3.2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 3.3 LAN91C111 Physical Layer to Internal MAC Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 7.1 MI Serial Port Frame Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 7.2 MII Frame Format & MII Nibble Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 7.3 TX/10BT Frame Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 7.4 TP Output Voltage Template - 10 MBPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Figure 7.5 TP Input Voltage Template -10MBPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Figure 7.6 SOI Output Voltage Template - 10MBPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Figure 7.7 Link Pulse Output Voltage Template - NLP, FLP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Figure 7.8 NLP VS. FLP Link Pulse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Figure 8.1 Data Frame Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Figure 8.2 Interrupt Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Figure 10.1 Interrupt Service Routine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Figure 10.2 RX INTR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Figure 10.3 TX INTR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Figure 10.4 TXEMPTY INTR (Assumes Auto Release Option Selected) . . . . . . . . . . . . . . . . . . . . . . . . 102
Figure 10.5 Drive Send and Allocate Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Figure 10.6 Interrupt Generation for Transmit, Receive, MMU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Figure 11.1 64 X 16 Serial EEPROM Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Figure 12.1 LAN91C111 on VL BUS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Figure 12.2 LAN91C111 on ISA BUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Figure 12.3 LAN91C111 on EISA BUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Figure 14.1 Asynchronous Cycle - nADS=0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Figure 14.2 Asynchronous Cycle - Using nADS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Figure 14.3 Asynchronous Cycle - nADS=0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Figure 14.4 Asynchronous Ready . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Figure 14.5 Burst Write Cycles - nVLBUS=1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Figure 14.6 Burst Read Cycles - nVLBUS=1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Figure 14.7 Address Latching for All Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Figure 14.8 Synchronous Write Cycle - nVLBUS=0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Figure 14.9 Synchronous Read Cycle - nVLBUS=0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Figure 14.10MII Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Figure 14.11Transmit Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Figure 14.12Receive Timing, End of Packet - 10 MBPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Figure 14.13Collision Timing, Receive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Figure 14.14Collision Timing, Transmit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Figure 14.15Jam Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Figure 14.16Link Pulse Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Figure 14.17FLP Link Pulse Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Figure 15.1 128 Pin TQFP Package Outline, 14X14X1.0 Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Figure 15.2 128 Pin QFP Package Outline, 3.9 MM Footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
SMSC LAN91C111-REV B
9
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Revision 1.8 (07-13-05)
10
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
List of Tables
Table 0.1 LAN91C111 Datasheet Revision History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Table 4.1 LAN91C111 Pin Requirements (128 Pin QFP and 1.0mm TQFP package) . . . . . . . . . . . . . . 21
Table 7.1 4B/5B Symbol Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Table 7.2 Transmit Level Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Table 8.1 Internal I/O Space Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Table 9.1 MII Serial Frame Structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Table 9.2 MII Serial Port Register MAP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Table 10.1 Typical Flow Of Events For Placing Device In Low Power Mode . . . . . . . . . . . . . . . . . . . . . . 95
Table 10.2 Flow Of Events For Restoring Device In Normal Power Mode . . . . . . . . . . . . . . . . . . . . . . . . 96
Table 12.1 VL Local Bus Signal Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Table 12.2 High-End ISA or Non-Burst EISA Machines Signal Connectors . . . . . . . . . . . . . . . . . . . . . . 113
Table 12.3 EISA 32 Bit Slave Signal Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Table 14.1 Transmit Timing Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Table 14.2 Receive Timing Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Table 14.3 Collision and Jam Timing Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Table 14.4 Link Pulse Timing Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Table 15.1 128 Pin TQFP Package Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Table 15.2 128 Pin QFP Package Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
SMSC LAN91C111-REV B
11
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Revision 1.8 (07-13-05)
12
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Chapter 1 General Description
The SMSC LAN91C111 is designed to facilitate the implementation of a third generation of Fast
Ethernet connectivity solutions for embedded applications. For this third generation of products,
flexibility and integration dominate the design requirements. The LAN91C111 is a mixed signal
Analog/Digital device that implements the MAC and PHY portion of the CSMA/CD protocol at 10 and
100 Mbps. The design will also minimize data throughput constraints utilizing a 32-bit, 16-bit or 8-bit
bus Host interface in embedded applications.
The total internal memory FIFO buffer size is 8 Kbytes, which is the total chip storage for transmit and
receive operations.
The SMSC LAN91C111 is software compatible with the LAN9000 family of products.
Memory management is handled using a patented optimized MMU (Memory Management Unit)
architecture and a 32-bit wide internal data path. This I/O mapped architecture can sustain back-toback frame transmission and reception for superior data throughput and optimal performance. It also
dynamically allocates buffer memory in an efficient buffer utilization scheme, reducing software tasks
and relieving the host CPU from performing these housekeeping functions.
The SMSC LAN91C111 provides a flexible slave interface for easy connectivity with industry-standard
buses. The Bus Interface Unit (BIU) can handle synchronous as well as asynchronous transfers, with
different signals being used for each one. Asynchronous bus support for ISA is supported even though
ISA cannot sustain 100 Mbps traffic. Fast Ethernet data rates are attainable for ISA-based nodes on
the basis of the aggregate traffic benefits.
Two different interfaces are supported on the network side. The first Interface is a standard Magnetics
transmit/receive pair interfacing to 10/100Base-T utilizing the internal physical layer block. The second
interface follows the MII (Media Independent Interface) specification standard, consisting of 4 bit wide
data transfers at the nibble rate. This interface is applicable to 10 Mbps standard Ethernet or 100 Mbps
Ethernet networks. Three of the LAN91C111’s pins are used to interface to the two-line MII serial
management protocol.
The SMSC LAN91C111 integrates IEEE 802.3 Physical Layer for twisted pair Ethernet applications.
The PHY can be configured for either 100 Mbps (100Base-TX) or 10 Mbps (10Base-T) Ethernet
operation. The Analog PHY block consists of a 4B5B/Manchester encoder/decoder, scrambler/descrambler, transmitter with wave shaping and output driver, twisted pair receiver with on chip equalizer
and baseline wander correction, clock and data recovery, Auto-Negotiation, controller interface (MII),
and serial port (MI). Internal output wave shaping circuitry and on-chip filters eliminate the need for
external filters normally required in 100Base-TX and 10Base-T applications.
The LAN91C111 can automatically configure itself for 100 or 10 Mbps and Full or Half Duplex operation
with the on-chip Auto-Negotiation algorithm. The LAN91C111 is ideal for media interfaces for
embedded application desiring Ethernet connectivity as well as 100Base-TX/10Base-T adapter cards,
motherboards, repeaters, switching hubs. The LAN91C111 operates from a single 3.3V supply. The
inputs and outputs of the host Interface are 5V tolerant and will directly interface to other 5V devices.
SMSC LAN91C111-REV B
13
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Revision 1.8 (07-13-05)
14
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Chapter 2 Pin Configurations
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
XTAL2
XTAL1
RX_ER
RX_DV
RXD0
RXD1
RXD2
RXD3
VDD
CRS100
RX25
GND
TXD0
TXD1
TXD2
TXD3
COL100
TXEN100
VDD
TX25
GND
D0
D1
D2
D3
GND
D4
D5
D6
D7
VDD
nBE3
Pin Configuration
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
LAN91C111FEASTTM
128 PIN TQFP
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
nBE2
nBE1
nBE0
GND
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
VDD
D8
D9
D10
D11
GND
D12
D13
D14
D15
GND
D16
D17
VDD
nDATACS
nCYCLE
W/nR
nADS
ARDY
GND
nVLBUS
AEN
LCLK
nSRDY
VDD
nLDEV
nRDYRTN
X25OUT
D31
D30
D29
D28
GND
D27
D26
D25
D24
GND
D23
D22
D21
D20
VDD
D19
D18
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
VDD
nCSOUT
IOS0
IOS1
IOS2
ENEEP
EEDO
EEDI
EESK
EECS
AVDD
RBIAS
AGND
TPO+
TPOAVDD
TPI+
TPIAGND
nLNK
LBK
nLEDA
nLEDB
GND
MDI
MDO
MCLK
nCNTRL
INTR0
RESET
nRD
nWR
Figure 2.1 Pin Configuration - LAN91C111-FEAST 128 PIN TQFP
SMSC LAN91C111-REV B
15
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
RX_ER
RX_DV
RXD0
RXD1
RXD2
RXD3
VDD
CRS100
RX25
GND
TXD0
TXD1
TXD2
TXD3
COL100
TXEN100
VDD
TX25
GND
D0
D1
D2
D3
GND
D4
D5
Pin Configuration
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
LAN91C111FEASTTM
128 PIN QFP
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
D6
D7
VDD
nBE3
nBE2
nBE1
nBE0
GND
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
VDD
D8
D9
D10
D11
GND
D12
D13
D14
D15
GND
D16
D17
D18
D19
nADS
ARDY
GND
nVLBUS
AEN
LCLK
nSRDY
VDD
nLDEV
nRDYRTN
X25OUT
D31
D30
D29
D28
GND
D27
D26
D25
D24
GND
D23
D22
D21
D20
VDD
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
XTAL1
XTAL2
VDD
nCSOUT
IOS0
IOS1
IOS2
ENEEP
EEDO
EEDI
EESK
EECS
AVDD
RBIAS
AGND
TPO+
TPOAVDD
TPI+
TPIAGND
nLNK
LBK
nLEDA
nLEDB
GND
MDI
MDO
MCLK
nCNTRL
INTR0
RESET
nRD
nWR
VDD
nDATACS
nCYCLE
W/nR
Figure 2.2 Pin Configuration - LAN91C111-FEAST 128 PIN QFP
Revision 1.8 (07-13-05)
16
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Chapter 3 Block Diagrams
The diagram shown in Figure 3.1, "Basic Functional Block Diagram", describes the device basic
functional blocks. The SMSC LAN91C111 is a single chip solution for embedded designs with minimal
Host and external supporting devices required to implement 10/100 Ethernet connectivity solutions.
The optional Serial EEPROM is used to store information relating to default IO offset parameters as
well as which of the Interrupt line are used by the host.
Host System
LAN91C111
ISA,Embedded
Processor
Ethernet
MAC
Internal IEEE 802.3 MII (Media
Independent Interface)
PHY
Core
Transformer
RJ45
TX/RX Buffer (8K)
Serial
EEProm
(Optional)
Minimal LAN91C111
Configuration
Figure 3.1 Basic Functional Block Diagram
SMSC LAN91C111-REV B
17
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
EEPROM
INTERFACE
MII
Control
Control
Control
Control
Address
8-32 bit
Bus
Interface
Unit
Control
Arbiter
Control
TPO
Control
WR
FIFO
Data
RD
FIFO
MMU
Ethernet
Protocol
Handler
(EPH)
DMA
TX/RX
FIFO
Pointer
TX Data
8K Byte
Dynamically
Allocated
SRAM
10/100
PHY
TXD[0-3]
32-bit Data
32-bit Data
TPI
RX Data
RXD[0-3]
Figure 3.2 Block Diagram
The diagram shown in Figure 3.2 describes the supported Host interfaces, which include ISA or
Generic Embedded. The Host interface is an 8, 16 or 32 bit wide address / data bus with extensions
for 32, 16 and 8 bit embedded RISC and ARM processors.
The figure shown next page describes the SMSC LAN91C111 functional blocks required to integrate
a 10/100 Ethernet Physical layer framer to the internal MAC.
Revision 1.8 (07-13-05)
18
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
EECS
EESK
EEDO
EEDI
MII External
Signals
RBIAS
EEPROM
CONTROL
To MII External Signals
4B5B
ENCODER
MLT3
ENCODER
SCRAMBLER
LP
FILTER
+
TPO+
-
TPO-
CLOCK
GEN
(PLL)
10BASE-T
TRANSMITTER
MANCHESTER
CRS100
COL100
ROM
DAC
+
LP
FILTER
-
CLOCK
GEN
(PLL)
COLLISION
RXD[3:0]
RX_ER
RX_DV
RX25
SQUELCH
4B5B
DECODER
MII
SERIAL
Manage
-ment
SWITCHED
CURRENT
SOURCE
CLOCK &
DATA
RECOVERY
DESCRAMBL
ER
100BASE-TX
RECEIVER
+/- Vth
MLT
ENCODER
+
+
CSMA/CD
TXD[3:0]
TX_ER
TXEN100
TX25
100BASE-TX
TRANSMITTER
TPI+
ADAPTIVE
EQUALIZER
TPI-
AUTO
NEGOTIATION
& LINK
MDI
MCLK
MDO
SQUELCH
10BASE-T
RECEIVER
+/- Vth
MII
CLOCK &
DATA
Recovery
(Manchester
Decoder)
LP
FILTER
+
+
Multiplexer
S1
Power
On
Reset
PHY
CONTROLS
nPLED[0-5]
AUTONEG
LOGIC
C1
LED
Control
LS[2-0]A
D
LEDA
S8
C2
C3
EN
B
Multiplexer
S1
D
LED
S8
C1
C2
C3
EN
B
LS[2-0]B
Figure 3.3 LAN91C111 Physical Layer to Internal MAC Block Diagram
SMSC LAN91C111-REV B
19
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Revision 1.8 (07-13-05)
20
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Chapter 4 Signal Descriptions
Table 4.1 LAN91C111 Pin Requirements (128 Pin QFP and 1.0mm TQFP package)
FUNCTION
PIN SYMBOLS
NUMBER OF PINS
System Address Bus
A1-A15, AEN, nBE0-nBE3
20
System Data Bus
D0-D31
32
System Control Bus
RESET, nADS, LCLK, ARDY,
nRDYRTN, nSRDY, INTR0, nLDEV,
nRD, nWR, nDATACS, nCYCLE, W/nR,
nVLBUS
14
Serial EEPROM
EEDI, EEDO, EECS, EESK, ENEEP,
IOS0-IOS2
8
LEDs
nLEDA, nLEDB
2
PHY
TPO+, TPO-, TPI+, TPI-, nLNK, LBK,
nCNTRL, RBIAS
8
Crystal Oscillator
XTAL1, XTAL2
2
Power
VDD, AVDD
10
Ground
GND, AGND
12
Physical Interface (MII)
TXEN100, CRS100, COL100, RX_DV,
RX_ER, TXD0-TXD3, RXD0-RXD3,
MDI, MDO, MCLK, RX25, TX25
18
MISC
nCSOUT, X25OUT
2
TOTAL
SMSC LAN91C111-REV B
128
21
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Revision 1.8 (07-13-05)
22
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Chapter 5 Description of Pin Functions
PIN NO.
NAME
SYMBOL
BUFFER
TYPE
DESCRIPTION
TQFP
QFP
81-92
83-94
Address
A4-A15
I**
Input. Decoded by LAN91C111 to
determine access to its registers.
78-80
80-82
Address
A1-A3
I**
Input. Used by LAN91C111 for internal
register selection.
41
43
Address Enable
AEN
I**
Input. Used as an address qualifier.
Address decoding is only enabled when
AEN is low.
94-97
96-99
nByte Enable
nBE0nBE3
I**
Input. Used during LAN91C111 register
accesses to determine the width of the
access and the register(s) being
accessed. nBE0-nBE3 are ignored when
nDATACS is low (burst accesses)
because 32 bit transfers are assumed.
107-104,
102-99, 7673, 71-68,
66-63, 6158, 56-53,
51-48
109-106,
104-101,
78-75, 7370, 68-65,
63-60, 5855, 53-50
Data Bus
D0-D31
I/O24**
Bidirectional. 32 bit data bus used to
access the LAN91C111’s internal
registers. Data bus has weak internal
pullups. Supports direct connection to the
system bus without external buffering.
For 16 bit systems, only D0-D15 are
used.
30
32
Reset
RESET
IS**
Input. When this pin is asserted high, the
controller performs an internal system
(MAC & PHY) reset. It programs all the
registers to their default value, the
controller will read the EEPROM device
through the EEPROM interface (Note 5.1).
This input is not considered active unless
it is active for at least 100ns to filter
narrow glitches.
37
39
nAddress
Strobe
nADS
IS**
Input. For systems that require address
latching, the rising edge of nADS
indicates the latching moment for A1-A15
and AEN. All LAN91C111 internal
functions of A1-A15, AEN are latched
except for nLDEV decoding.
35
37
nCycle
nCYCLE
I**
Input. This active low signal is used to
control LAN91C111 EISA burst mode
synchronous bus cycles.
36
38
Write/
nRead
W/nR
IS**
Input. Defines the direction of
synchronous cycles. Write cycles when
high, read cycles when low.
40
42
nVL Bus Access nVLBUS
I with
pullup**
Input. When low, the LAN91C111
synchronous bus interface is configured
for VL Bus accesses. Otherwise, the
LAN91C111 is configured for EISA DMA
burst accesses. Does not affect the
asynchronous bus interface.
SMSC LAN91C111-REV B
23
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
PIN NO.
NAME
BUFFER
TYPE
SYMBOL
DESCRIPTION
TQFP
QFP
42
44
Local Bus Clock LCLK
I**
Input. Used to interface synchronous
buses. Maximum frequency is 50 MHz.
Limited to 8.33 MHz for EISA DMA burst
mode. This pin should be tied high if it is
in asynchronous mode.
38
40
Asynchronous
Ready
ARDY
OD16
Open drain output. ARDY may be used
when interfacing asynchronous buses to
extend accesses. Its rising (access
completion) edge is controlled by the
XTAL1 clock and, therefore,
asynchronous to the host CPU or bus
clock. ARDY is negated during
Asynchronous cycle when one of the
following conditions occurs:
No_Wait Bit in the Configuration Register
is cleared.
Read FIFO contains less than 4 bytes
when read.
Write FIFO is full when write.
43
45
nSynchronous
Ready
nSRDY
O16
Output. This output is used when
interfacing synchronous buses and
nVLBUS=0 to extend accesses. This
signal remains normally inactive, and its
falling edge indicates completion. This
signal is synchronous to the bus clock
LCLK.
46
48
nReady Return
nRDYRTN
I**
Input. This input is used to complete
synchronous read cycles. In EISA burst
mode it is sampled on falling LCLK
edges, and synchronous cycles are
delayed until it is sampled high.
29
31
Interrupt
INTR0
O24
Interrupt Output – Active High, it’s used to
interrupt the Host on a status event.
Note: The selection bits used to
determined by the value of INT SEL 1-0
bits in the Configuration Register are no
longer required and have been set to
reserved in this revision of the FEAST
family of devices.
45
47
nLocal Device
nLDEV
O16
Output. This active low output is asserted
when AEN is low and A4-A15 decode to
the LAN91C111 address programmed
into the high byte of the Base Address
Register. nLDEV is a combinatorial
decode of unlatched address and AEN
signals.
31
33
nRead Strobe
nRD
IS**
Input. Used in asynchronous bus
interfaces.
32
34
nWrite Strobe
nWR
IS**
Input. Used in asynchronous bus
interfaces.
34
36
nData Path
Chip Select
nDATACS
I with
pullup**
Input. When nDATACS is low, the Data
Path can be accessed regardless of the
values of AEN, A1-A15 and the content of
the BANK SELECT Register. nDATACS
provides an interface for bursting to and
from the LAN91C111 32 bits at a time.
Revision 1.8 (07-13-05)
24
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
PIN NO.
NAME
SYMBOL
BUFFER
TYPE
DESCRIPTION
TQFP
QFP
9
11
EEPROM Clock
EESK
O4
Output. 4 µsec clock used to shift data in
and out of the serial EEPROM.
10
12
EEPROM
Select
EECS
O4
Output. Serial EEPROM chip select.
Used for selection and command framing
of the serial EEPROM.
7
9
EEPROM Data
Out
EEDO
O4
Output. Connected to the DI input of the
serial EEPROM.
8
10
EEPROM Data
In
EEDI
I with
Input. Connected to the DO output of the
pulldown ** serial EEPROM.
3-5
5-7
I/O Base
IOS0-IOS2
I with
pullup**
Input. External switches can be
connected to these lines to select
between predefined EEPROM
configurations.
6
8
Enable
EEPROM
ENEEP
I with
pullup**
Input. Enables (when high or open)
LAN91C111 accesses to the serial
EEPROM. Must be grounded if no
EEPROM is connected to the
LAN91C111.
127, 128
1, 2
Crystal 1
Crystal 2
XTAL1
XTAL2
Iclk**
An external 25 MHz crystal is connected
across these pins. If a TTL clock is
supplied instead, it should be connected
to XTAL1 and XTAL2 should be left open.
XTAL1 is the 5V tolerant input of the
internal amplifier and XTAL2 is the output
of the internal amplifier.
1, 33, 44,
62, 77, 98,
110, 120
3, 35, 46,
64, 79,
100, 112,
122
Power
VDD
+3.3V Power supply pins.
11, 16
13, 18
Analog Power
AVDD
+3.3V Analog power supply pins.
24, 39, 52,
57, 67, 72,
93, 103,
108, 117
26, 41, 54,
59, 69, 74,
95, 105,
110, 119
Ground
GND
Ground pins.
13, 19
15, 21
Analog Ground
AGND
Analog Ground pins
21
23
Loopback
LBK
O4
Output. Active when LOOP bit is set
(TCR bit 1).
20
22
nLink Status
nLNK
I with
pullup
Input. General-purpose input port used to
convey LINK status (EPHSR bit 14).
28
30
nCNTRL
nCNTRL
O12
General Purpose Control Pin
47
49
X25out
X25out
O12
25Mhz Output to external PHY
111
113
Transmit Enable
100 Mbps
TXEN100
O12
Output to MII PHY. Envelope to 100
Mbps transmission.
119
121
Carrier Sense
100 Mbps
CRS100
I with
pulldown
Input from MII PHY. Envelope of packet
reception used for deferral and backoff
purposes.
SMSC LAN91C111-REV B
25
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
PIN NO.
NAME
SYMBOL
BUFFER
TYPE
DESCRIPTION
TQFP
QFP
125
127
Receive Data
Valid
RX_DV
I with
pulldown
Input from MII PHY. Envelope of data
valid reception. Used for receive data
framing.
112
114
Collision Detect
100 Mbps
COL100
I with
pulldown
Input from MII PHY. Collision detection
input.
113-116
115-118
Transmit Data
TXD3TXD0
O12
Outputs. Transmit Data nibble to MII
PHY.
109
111
Transmit Clock
TX25
I with
pullup
Input. Transmit clock input from MII.
Nibble rate clock (25MHz for 100Mbps &
2.5MHz for 10Mbps).
118
120
Receive Clock
RX25
I with
pullup
Input. Receive clock input from MII PHY.
Nibble rate clock. (25MHz for 100Mbps &
2.5MHz for 10Mbps).
121-124
123-126
Receive Data
RXD3RXD0
I with
pullup
Inputs. Received Data nibble from MII
PHY.
25
27
Management
Data Input
MDI
I with
pulldown
MII management data input.
26
28
Management
Data Output
MDO
O4
MII management data output.
27
29
Management
Clock
MCLK
O4
MII management clock.
126
128
Receive Error
RX_ER
I with
pulldown
Input. Indicates a code error detected by
PHY. Used by the LAN91C111 to discard
the packet being received. The error
indication reported for this event is the
same as a bad CRC (Receive Status
Word bit 13).
2
4
nChip Select
Output
nCSOUT
O4
Output. Chip Select provided for
mapping of PHY functions into
LAN91C111 decoded space. Active on
accesses to LAN91C111’s eight lower
addresses when the BANK SELECTED is
7.
12
14
External
Resistor
RBIAS
NA
Transmit Current Set. An external
resistor connected between this pin and
GND will set the output current for the TP
transmit outputs
14
16
TPO+
O/I
Twisted Pair Transmit Output, Positive.
15
17
TPO-
O/I
Twisted Pair Transmit Output, Negative
17
19
TPI+
I/O
Twisted Pair Receive Input, Positive
18
20
TPI-
I/O
Twisted Pair Receive Input, Negative.
22
24
nLEDA
OD24
PHY LED Output
23
25
nLEDB
OD24
PHY LED Output
Note 5.1
Revision 1.8 (07-13-05)
If the EEPROM is enabled.
26
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Chapter 6 Signal Description Parameters
This section provides a detailed description of each SMSC LAN91C111 signal. The signals are
arranged in functional groups according to their associated function.
The ‘n’ symbol at the beginning of a signal name indicates that it is an active low signal. When ‘n’ is
not present before the signal name, it indicates an active high signal.
The term “assert” or “assertion” indicates that a signal is active; independent of whether that level is
represented by a high or low voltage. The term negates or negation indicates that a signal is inactive.
The term High-Z means tri-stated.
The term Undefined means the signal could be high, low, tri-stated, or in some in-between level.
6.1
Buffer Types
O4
Output buffer with 2mA source and 4mA sink
O12
Output buffer with 6mA source and 12mA sink
O16
Output buffer with 8mA source and 16mA sink
O24
Output buffer with 12mA source and 24mA sink
OD16
Open drain buffer with 16mA sink
OD24
Open drain buffer with 24mA sink
I/O4
Bidirectional buffer with 2mA source and 4mA sink
I/O24
Bidirectional buffer with 12mA source and 24mA sink
I/OD
Bidirectional Open drain buffer with 4mA sink
I
Input buffer
IS
Input buffer with Schmitt Trigger Hysteresis
Iclk
Clock input buffer
I/O
Differential Input
O/I
Differential Output
**
5V tolerant. Input pins are able to accept 5V signals
DC levels and conditions defined in the DC Electrical Characteristics section
SMSC LAN91C111-REV B
27
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Revision 1.8 (07-13-05)
28
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Chapter 7 Functional Description
7.1
Clock Generator Block
1. The XTAL1 and XTAL2 pins are to be connected to a 25 MHz crystal.
2. TX25 is an input clock. It will be the nibble rate of the particular PHY connected to the MII (2.5
MHz for a 10 Mbps PHY, and 25 MHz for a 100 Mbps PHY).
3. RX25 - This is the MII nibble rate receive clock used for sampling received data nibbles and
running the receive state machine. (2.5 MHz for a 10 Mbps PHY, and 25 MHz for a 100 Mbps PHY).
4. LCLK - Bus clock - Used by the BIU for synchronous accesses. Maximum frequency is 50 MHz
for VL BUS mode, and 8.33 MHz for EISA slave DMA.
7.2
CSMA/CD Block
This is a 16 bit oriented block, with fully- independent Transmit and Receive logic. The data path in
and out of the block consists of two 16-bit wide uni-directional FIFOs interfacing the DMA block. The
DMA port of the FIFO stores 32 bits to exploit the 32 bit data path into memory, but the FIFOs
themselves are 16 bit wide. The Control Path consists of a set of registers interfaced to the CPU via
the BIU.
7.2.1
DMA Block
This block accesses packet memory on the CSMA/CD’s behalf, fetching transmit data and storing
received data. It interfaces the CSMA/CD Transmit and Receive FIFOs on one side and the Arbiter
block on the other. To increase the bandwidth into memory, a 50 MHz clock is used by the DMA block,
and the data path is 32 bits wide.
For example, during active reception at 100 Mbps, the CSMA/CD block will write a word into the
Receive FIFO every 160ns. The DMA will read the FIFO and accumulate two words on the output port
to request a memory cycle from the Arbiter every 320ns.
The DMA machine is able to support full duplex operation. Independent receive and transmit counters
are used. Transmit and receive cycles are alternated when simultaneous receive and transmit
accesses are needed.
7.2.2
Arbiter Block
The Arbiter block sequences accesses to packet RAM requested by the BIU and by the DMA blocks.
BIU requests represent pipelined CPU accesses to the Data Register, while DMA requests represent
CSMA/CD data movement.
Internal SRAM read accesses are always 32 bit wide, and the Arbiter steers the appropriate byte(s) to
the appropriate lanes as a function of the address.
The CPU Data Path consists of two uni-directional FIFOs mapped at the Data Register location. These
FIFOs can be accessed in any combination of bytes, word, or doublewords. The Arbiter will indicate
'Not Ready' whenever a cycle is initiated that cannot be satisfied by the present state of the FIFO.
7.3
MMU Block
The Hardware Memory Management Unit allocates memory and transmit and receive packet queues.
It also determines the value of the transmit and receive interrupts as a function of the queues. The
page size is 2048 bytes, with a maximum memory size of 8kbytes. MIR values are interpreted in 2048
byte units.
SMSC LAN91C111-REV B
29
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
7.4
BIU Block
The Bus Interface Unit can handle synchronous as well as asynchronous buses; different signals are
used for each one. Transparent latches are added on the address path using rising nADS for latching.
When working with an asynchronous bus like ISA, the read and write operations are controlled by the
edges of nRD and nWR. ARDY is used for notifying the system that it should extend the access cycle.
The leading edge of ARDY is generated by the leading edge of nRD or nWR while the trailing edge
of ARDY is controlled by the internal LAN91C111 clock and, therefore, asynchronous to the bus.
In the synchronous VL Bus type mode, nCYCLE and LCLK are used to for read and write operations.
Completion of the cycle may be determined by using nSRDY. nSRDY is controlled by LCLK and
synchronous to the bus.
Direct 32 bit access to the Data Path is supported by using the nDATACS input. By asserting
nDATACS, external DMA type of devices will bypass the BIU address decoders and can sequentially
access memory with no CPU intervention. nDATACS accesses can be used in the EISA DMA burst
mode (nVLBUS=1) or in asynchronous cycles. These cycles MUST be 32 bit cycles. Please refer to
the corresponding timing diagrams for details on these cycles.
The BIU is implemented using the following principles:
a. Address decoding is based on the values of A15-A4 and AEN.
b. Address latching is performed by using transparent latches that are transparent when nADS=0 and
nRD=1, nWR=1 and latch on nADS rising edge.
c. Byte, word and doubleword accesses to all registers and Data Path are supported except a
doubleword write to offset Ch will only write the BANK SELECT REGISTER (offset 0x0Fh).
d. No bus byte swapping is implemented (no eight bit mode).
e. Word swapping as a function of A1 is implemented for 16 bit bus support.
f.
The asynchronous interface uses nRD and nWR strobes. If necessary, ARDY is negated on the
leading edge of the strobe. The ARDY trailing edge is controlled by CLK.
g. The VLBUS synchronous interface uses LCLK, nADS, and W/nR as defined in the VESA
specification as well as nCYCLE to control read and write operations and generate nSRDY.
h. EISA burst DMA cycles to and from the DATA REGISTER are supported as defined in the EISA
Slave Mode "C" specification when nDATACS is driven by nDAK.
7.5
i.
Synchronous and asynchronous cycles can be mixed as long as they are not active simultaneously.
j.
Address and bank selection can be bypassed to generate 32 bit Data Path accesses by activating
the nDATACS pin.
MAC-PHY Interface
The LAN91C111 integrates the IEEE 802.3 Physical Layer (PHY) and Media Access Control (MAC)
into the same silicon. The data path connection between the MAC and the internal PHY is provided
by the internal MII. The LAN91C111 also supports the EXT_PHY mode for the use of an external PHY,
such as HPNA. This mode isolates the internal PHY to allow interface with an external PHY through
the MII pins. To enter this mode, set EXT PHY bit to 1 in the Configuration Register.
7.5.1
Management Data Software Implementation
The MII interface contains of a pair of signals that physically transport the management information
across the MII, a frame format and a protocol specification for exchanging management frames, and
a register set that can be read and written using these frames. MII management refers to the ability
of a management entity to communicate with PHY via the MII serial management interface (MI) for the
purpose of displaying, selecting and/or controlling different PHY options. The host manipulates the
MAC to drive the MII management serial interface. By manipulating the MAC's registers, MII
management frames are generated on the management interface for reading or writing information
from the PHY registers. Timing and framing for each management command is to be generated by
the CPU (host).
Revision 1.8 (07-13-05)
30
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
The MAC and external PHY communicate via MDIO and MDC of the MII Management serial interface.
MDIO:Management Data input/output. Bi-directional between MAC and PHY that carries management
data. All control and status information sent over this pin is driven and sampled synchronously to the
rising edge of MDC signal.
MDC:Management Data Clock. Sourced by the MAC as a timing reference for transfer of information
on the MDIO signal. MDC is a periodic signal with no maximum high or low times. The minimum high
and low times should be 160ns each and the minimum period of the signal should be 400ns. These
values are regardless of the nominal period of the TX and RX clocks.
7.5.2
Management Data Timing
A timing diagram for a Ml serial port frame is shown in Figure 7.1. The Ml serial port is idle when at
least 32 continuous 1's are detected on MDIO and remains idle as long as continuous 1's are detected.
During idle, MDIO is in the high impedance state. When the Ml serial port is in the idle state, a 01
pattern on the MDIO initiates a serial shift cycle. Data on MDIO is then shifted in on the next 14 rising
edges of MDC (MDIO is high impedance). If the register access mode is not enabled, on the next 16
rising edges of MDC, data is either shifted in or out on MDIO, depending on whether a write or read
cycle was selected with the bits READ and WRITE. After the 32 MDC cycles have been completed,
one complete register has been read/written, the serial shift process is halted, data is latched into the
device, and MDIO goes into high impedance state. Another serial shift cycle cannot be initiated until
the idle condition (at least 32 continuous 1's) is detected.
7.5.3
MI Serial Port Frame Structure
The structure of the PHY serial port frame is shown in Table 9.1 and timing diagram of a frame is
shown in Figure 7.1. Each serial port access cycle consists of 32 bits (or 192 bits if multiple register
access is enabled and REGAD[4:0]=11111), exclusive of idle. The first 16 bits of the serial port cycle
are always write bits and are used for addressing. The last 16/176 bits are from one/all of the 11 data
registers.
The first 2 bit in Table 9.1and Figure 7.1 are start bits and need to be written as a 01 for the serial port
cycle to continue. The next 2 bits are a read and write bit which determine if the accessed data register
bits will be read or write. The next 5 bits are device addresses. The next 5 bits are register address
select bits, which select one of the five data registers for access. The next 1 bit is a turnaround bit
which is not an actual register bit but extra time to switch MDIO from write to read if necessary, as
shown in Figure 7.1. The final 16 bits of the PHY Ml serial port cycle (or 176 bits if multiple register
access is enabled and REGAD[4:0]=11111) come from the specific data register designated by the
register address bits REGAD[4:0].
SMSC LAN91C111-REV B
31
DATASHEET
Revision 1.8 (07-13-05)
Revision 1.8 (07-13-05)
DATASHEET
32
MDIO
MDC
MDIO
MDC
ST[1:0]
0
0
READ CYCLE
ST[1:0]
0
0
WRITE CYCLE
1
1
1
1
OP[1:0]
1
2
OP[1:0]
0
2
0
1
3
3
P4
P3
P2
6
PHYAD[4:0]
P2
6
PHYAD[4:0]
5
P3
5
P1
7
P1
7
P0
8
P0
8
R4
9
R4
9
R3
R2
11
12
R1
REGAD[4:0]
R2
11
R1
12
R0
13
1
15
0
TA[1:0]
14
D15
16
D14
17
D13
18
R0
13
TA[1:0]
Z
14
0
15
D15
16
D14
17
D13
18
WRITE
BITS
PHY CLOCKS IN DATA ON RISING EDGES OF MDC
REGAD[4:0]
10
R3
10
WRITE
BITS
PHY CLOCKS IN DATA ON RISING EDGES OF MDC
4
P4
4
D12
19
D12
19
D10
21
D10
21
D9
22
D9
22
DATA[15:0]
D8
23
24
D7
24
D7
DATA[15:0]
D8
23
D6
25
D6
25
D5
26
D5
26
READ BITS
PHY CLOCKS OUT DATA ON RISING EDGES OF MDC
D11
20
D11
20
D4
27
D4
27
D3
28
D3
28
D2
29
D2
29
D1
30
D1
30
D0
31
D0
31
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Figure 7.1 MI Serial Port Frame Timing Diagram
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
7.5.4
MII Packet Data Communication with External PHY
The MIl is a nibble wide packet data interface defined in IEEE 802.3. The LAN91C111 meets all the
MIl requirements outlined in IEEE 802.3 and shown in Figure 7.2.
TX_EN = 1
TX_EN = 0
TX_EN = 0
START
IDLE
PREAMBLE
OF
FRAME
DELIM.
PRMBLE
SFD
62 BT
2 BT
IDLE
DATA NIBBLES
DATA 1
DATA 2
DATA N-1
DATA N
PREAMBLE = [ 1 0 1 0 ... ] 62 BITS LONG
SFD = [ 1 1 ]
DATAn = [ BETWEEN 64-1518 DATA BYTES ]
IDLE = TX_EN = 0
FIRST BIT
LSB
FIRST
NIBBLE
MAC's SERIAL BIT STREAM
D0
D1
D2
D3
D4
D5
D6
D7
MSB
SECOND
NIBBLE
TXD0 / RXD0
MII
NIBBLE
STREAM
TXD1 / RXD1
TXD2 / RXD2
TXD3 / RXD3
Figure 7.2 MII Frame Format & MII Nibble Order
The Mll consists of the following signals: four transmit data bits (TXD[3:0]), transmit clock
(TX25),transmit enable (TXEN100), four receive data bits(RXD[3:0]), receive clock(RX25), carrier
sense (CRS100), receive data valid (RX_DV), receive data error (RX_ER), and collision (COL100).
Transmit data is clocked out using the TX25 clock input, while receive data is clocked in using RX25. The
transmit and receive clocks operate at 25 MHz in 100Mbps mode and 2.5 MHz in 10Mbps.
In 100 Mbps mode, the LAN91C111 provides the following interface signals to the PHY:
■
For transmission: TXEN100, TXD0-3, TX25
■
For reception: RX_DV, RX_ER, RXD0-3, RX25
■
For CSMA/CD state machines: CRS100, COL100
A transmission begins by TXEN100 going active (high), and TXD0-TXD3 having the first valid
preamble nibble. TXD0 carries the least significant bit of the nibble (that is the one that would go first
out of the EPH at 100 Mbps), while TXD3 carries the most significant bit of the nibble. TXEN100 and
TXD0-TXD3 are clocked by the LAN91C111 using TX25 rising edges. TXEN100 goes inactive at the
end of the packet on the last nibble of the CRC.
During a transmission, COL100 might become active to indicate a collision. COL100 is asynchronous
to the LAN91C111’s clocks and will be synchronized internally to TX25.
Reception begins when RX_DV (receive data valid) is asserted. A preamble pattern or flag octet will
be present at RXD0-RXD3 when RX_DV is activated. The LAN91C111 requires no training sequence
beyond a full flag octet for reception. RX_DV as well as RXD0-RXD3 are sampled on RX25 rising
SMSC LAN91C111-REV B
33
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
edges. RXD0 carries the least significant bit and RXD3 the most significant bit of the nibble. RX_DV
goes inactive when the last valid nibble of the packet (CRC) is presented at RXD0-RXD3.
RX_ER might be asserted during packet reception to signal the LAN91C111 that the present receive
packet is invalid. The LAN91C111 will discard the packet by treating it as a CRC error.
RXD0-RXD3 should always be aligned to packet nibbles, therefore, opening flag detection does not
consider misaligned cases. Opening flag detection expects the 5Dh pattern and will not reject the
packet on non-preamble patterns.
CRS100 is used as a frame envelope signal for the CSMA/CD MAC state machines (deferral and
backoff functions), but it is not used for receive framing functions. CRS100 is an asynchronous signal
and it will be active whenever there is activity on the cable, including LAN91C111 transmissions and
collisions.
7.6
Serial EEPROM Interface
This block is responsible for reading the serial EEPROM upon hardware reset (or equivalent
command) and defining defaults for some key registers. A write operation is also implemented by this
block, that under CPU command will program specific locations in the EEPROM. This block is an
autonomous state machine and controls the internal Data Bus of the LAN91C111 during active
operation.
7.7
Internal Physical Layer
The LAN91C111 integrates the IEEE 802.3 physical layer (PHY) internally. The EXT PHY bit in the
Configuration Register is 0 as the default configuration to set the internal PHY enabled. The internal
PHY address is 00000, the driver must use this address to talk to the internal PHY. The internal PHY
is placed in isolation mode at power up and reset. It can be removed from isolation mode by clearing
the MII_DIS bit in the PHY Control Register. If necessary, the internal PHY can be enabled by clearing
the EXT_PHY bit in the Configuration Register.
The internal PHY of LAN91C111 has nine main sections: controller interface, encoder, decoder,
scrambler, descrambler, clock and data recovery, twisted pair transmitter, twisted pair receiver, and MI
serial port.
The LAN91C111 can operate as a 100BASE-TX device (hereafter referred to as 100Mbps mode) or
as a 10BASE-T device (hereafter referred to as 10Mbps mode). The difference between the 100Mbps
mode and the 10Mbps mode is data rate, signaling protocol, and allowed wiring. The 100Mbps TX
mode uses two pairs of category 5 or better UTP or STP twisted pair cable with 4B5B encoded,
scrambled, and MLT-3 coded 62.5 MHz ternary data to achieve a throughput of 100Mbps. The 10Mbps
mode uses two pairs of category 3 or better UTP or STP twisted pair cable with Manchester encoded,
10MHz binary data to achieve a 10Mbps throughput. The data symbol format on the twisted pair cable
for the 100 and 10Mbps modes are defined in IEEE 802.3 specifications and shown in Figure 7.3.
Revision 1.8 (07-13-05)
34
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
ETHERNET MAC
FRAME
INTERFRAME
GAP
SFD
PREAMBLE
DA
SA
LN
LLC DATA
FCS
LN
LLC DATA
FCS
INTERFRAME
GAP
100 BASE-TX DATA SYMBOLS
IDLE
SSD
DA
SFD
PREAMBLE
IDLE
SSD
SA
ESD
IDLE
SOI
IDLE
= [ 1 1 1 1...]
= [ 1 1 0 0 0 1 0 0 0 1]
BEFORE / AFTER
4B5B ENCODING,
SCRAMBLING,
AND MLT3
CODING
PREAMBLE = [ 1 0 1 0 ...] 62 BITS LONG
SFD = [ 1 1]
DA, SA, LN, LLC DATA, FCS = [ DATA]
ESD = [ 0 1 1 0 1 0 0 1 1 1]
10 BASE-T DATA SYMBOLS
IDLE
SFD
PREAMBLE
DA
SA
LN
IDLE
= [ NO TRANSITIONS]
PREAMBLE = [ 1 0 1 0 ... ] 62 BITS LONG
SFD = [ 1 1]
DA, SA, LN, LLC DATA, FCS
= [ DATA]
SOI = [ 1 1 ] WITH NO MID BIT TRANSITION
LLC DATA
FCS
BEFORE / AFTER
MANCHESTER
ENCODING
Figure 7.3 TX/10BT Frame Format
On the transmit side for 100Mbps TX operation, data is received on the controller and then sent to the
4B5B encoder for formatting. The encoded data is then sent to the scrambler. The scrambled and
encoded data is then sent to the TP transmitter. The TP transmitter converts the encoded and
scrambled data into MLT-3 ternary format, reshapes the output, and drives the twisted pair cable.
On the receive side for 100Mbps TX operation, the twisted pair receiver receives incoming encoded
and scrambled MLT-3 data from the twisted pair cable, remove any high frequency noise, equalizes
the input signal to compensate for the effects of the cable, qualifies the data with a squelch algorithm,
and converts the data from MLT-3 coded twisted pair levels to internal digital levels. The output of the
twisted pair receiver then goes to a clock and data recovery block which recovers a clock from the
incoming data, uses the clock to latch in valid data into the device, and converts the data back to NRZ
format. The NRZ data is then unscrambled and decoded by the 4B5B decoder and descrambler,
respectively, and outputted to the Ethernet controller.
SMSC LAN91C111-REV B
35
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
1 0 M b ps o p e r a t i o n i s s i m i l a r t o t h e 1 0 0 M b ps T X o p e r a t i o n e x c e p t , ( 1 ) t h e r e i s n o
scrambler/descrambler, (2) the encoder/decoder is Manchester instead of 4B5B, (3) the data rate is
10Mbps instead of 100Mbps, and (4) the twisted pair symbol data is two level Manchester instead of
ternary MLT-3.
The Management Interface, (hereafter referred to as the MI serial port), is a two pin bi-directional link
through which configuration inputs can be set and status outputs can be read. Each block plus the
operating modes are described in more detail in the following sections.
7.7.1
MII Disable
The internal PHY MII interface can be disabled by setting the MII disable bit in the MI serial port Control
register. When the MII is disabled, the MII inputs are ignored, the MII outputs are placed in high
impedance state, and the TP output is high impedance.
7.7.2
Encoder
4B5B Encoder - 100 Mbps
100BASE-TX requires that the data be 4B5B encoded. 4B5B coding converts the 4-Bit data nibbles
into 5-Bit date code words. The mapping of the 4B nibbles to the 5B code words is specified in IEEE
802.3. The 4B5B encoder on the LAN91C111 takes 4B nibbles from the controller interface, converts
them into 5B words and sends the 5B words to the scrambler. The 4B5B encoder also substitutes the
first 8 bits of the preamble with the SSD delimiters (a.k.a. /J/K/ symbols) and adds an ESD delimiter
(a.k.a. MR/ symbols) to the end of every packet, as defined in IEEE 802.3. The 4B5B encoder also
fills the period between packets, called the idle period, with the continuous stream of idle symbols.
Manchester Encoder - 10 Mbps
The Manchester encoding process combines clock and NRZ data such that the first half of the data
bit contains the complement of the data, and the second half of the data bit contains the true data, as
specified in IEEE 802.3. This guarantees that a transition always occurs in the middle of the bit call.
The Manchester encoder on the LAN91C111 converts the 10Mbps NRZ data from the controller
interface into a Manchester Encoded data stream for the TP transmitter and adds a start of idle pulse
(SOI) at the end of the packet as specified in IEEE 802.3. The Manchester encoding process is only
done on actual packet data, and the idle period between packets is not Manchester encoded and filled
with link pulses.
7.7.3
Decoder
4B5B Decoder - 100 Mbps
Since the TP input data is 4B5B encoded on the transmit side, it must also be decoded by the 4B5B
decoder on the receive side. The mapping of the 5B nibbles to the 4B code words is specified in IEEE
802.3. The 4B5B decoder on the LAN91C111 takes the 5B code words from the descrambler, converts
them into 4B nibbles per Table 2, and sends the 4B nibbles to the controller interface. The 4B5B
decoder also strips off the SSD delimiter (a.k.a. /J/K/ symbols) and replaces them with two 4B Data 5
nibbles (a.k.a. /5/ symbol), and strips off the ESD delimiter (a.k.a. /T/R/ symbols) and replaces it with
two 4B Data 0 nibbles (a.k.a. /I/symbol), per IEEE 802.3 specifications and shown in Figure 7.3.
Table 7.1 4B/5B Symbol Mapping
SYMBOL NAME
DESCRIPTION
5B CODE
4B CODE
0
Data 0
11110
0000
1
Data 1
01001
0001
2
Data 2
10100
0010
Revision 1.8 (07-13-05)
36
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Table 7.1 4B/5B Symbol Mapping (continued)
SYMBOL NAME
DESCRIPTION
5B CODE
4B CODE
3
Data 3
10101
0011
4
Data 4
01010
0100
5
Data 5
01011
0101
6
Data 6
01110
0110
7
Data 7
01111
0111
8
Data 8
10010
1000
9
Data 9
10011
1001
A
Data A
10110
1010
B
Data B
10111
1011
C
Data C
11010
1100
D
Data D
11011
1101
E
Data E
11100
1110
F
Data F
11101
1111
I
Idle
11111
0000
J
SSD #1
11000
0101
K
SSD #2
10001
0101
T
ESD #1
01101
0000
R
ESD #2
00111
0000
H
Halt
00100
Undefined
---
Invalid codes
All others*
0000*
* These 5B codes are not used. For decoder, these 5B codes are decoded to 4B 0000. For encoder,
4B 0000 is encoded to 5B 11110, as shown in symbol Data 0.
The 4B5B decoder detects SSD, ESD and codeword errors in the incoming data stream as specified
in IEEE 802.3. These errors are indicated by asserting RX_ER output while the errors are being
transmitted across RXD[3:0], and they are also indicated in the serial port by setting SSD, ESD, and
codeword error bits in the PHY MI serial port Status Output register.
Manchester Decoder - 10 Mbps
In Manchester coded data, the first half of the data bit contains the complement of the data, and the
second half of the data bit contains the true data. The Manchester decoder in the LAN91C111 converts
the Manchester encoded data stream from the TP receiver into NRZ data for the controller interface
by decoding the data and stripping off the SOI pulse. Since the clock and data recovery block has
already separated the clock and data from the TP receiver, the Manchester decoding process to NRZ
data is inherently performed by that block.
SMSC LAN91C111-REV B
37
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
7.7.4
Clock and Data Recovery
Clock Recovery - 100 Mbps
Clock recovery is done with a PLL. If there is no valid data present on the TP inputs, the PLL is locked
to the 25 MHz TX25. When valid data is detected on the TP inputs with the squelch circuit and when
the adaptive equalizer has settled, the PLL input is switched to the incoming data on the TP input.
The PLL then recovers a clock by locking onto the transitions of the incoming signal from the twisted
pair wire. The recovered dock frequency is a 25 MHz nibble dock, and that clock is outputted on the
controller interface signal RX25.
Data Recovery - 100 Mbps
Data recovery is performed by latching in data from the TP receiver with the recovered clock extracted
by the PLL. The data is then converted from a single bit stream into nibble wide data word according
to the format shown in Figure 7.2.
Clock Recovery - 10 Mbps
The clock recovery process for 10Mbps mode is identical to the 100Mbps mode except, (1) the
recovered clock frequency is 2.5 MHz nibble clock, (2) the PLL is switched from TX25 to the TP input
when the squelch indicates valid data, (3) The PLL takes up to 12 transitions (bit times) to lock onto
the preamble, so some of the preamble data symbols are lost, but the dock recovery block recovers
enough preamble symbols to pass at least 6 nibbles of preamble to the receive controller interface as
shown in Figure 7.2.
Data Recovery - 10 Mbps
The data recovery process for 10Mbps mode is identical to the 100Mbps mode. As mentioned in the
Manchester Decoder section, the data recovery process inherently performs decoding of Manchester
encoded data from the TP inputs.
7.7.5
Scrambler
100 Mbps
100BASE-TX requires scrambling to reduce the radiated emissions on the twisted pair. The
LAN91C111 scrambler takes the encoded data from the 4B5B encoder, scrambles it per the IEEE
802.3 specifications, and sends it to the TP transmitter.
10 Mbps
A scrambler is not used in 10Mbps mode.
Scrambler Bypass
The scrambler can be bypassed by setting the bypass scrambler/descrambler bit in the PHY Ml serial
port Configuration 1 register. When this bit is set, the 5B data bypasses the scrambler and goes
directly from the 4B5B encoder to the twisted pair transmitter.
7.7.6
Descrambler
100 Mbps
The LAN91C111 descrambler takes the scrambled data from the data recovery block, descrambles it
per the IEEE 802.3 specifications, aligns the data on the correct 5B word boundaries, and sends it to
the 4B5B decoder.
The algorithm for synchronization of the descrambler is the same as the algorithm outlined in the IEEE
802.3 specification. Once the descrambler is synchronized, it will maintain synchronization as long as
enough descrambled idle pattern 1's are defected within a given interval. To stay in synchronization,
the descrambler needs to detect at least 25 consecutive descrambled idle pattern 1's in a 1ms interval.
Revision 1.8 (07-13-05)
38
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
If 25 consecutive descrambled idle pattern 1's are not detected within the 1ms interval, the descrambler
goes out of synchronization and restarts the synchronization process.
If the descrambler is in the unsynchronized state, the descrambler loss of synchronization detect bit is
set in the Ml serial port Status Output register to indicate this condition. Once this bit is set, it will stay
set until the descrambler achieves synchronization.
10 Mbps
A descrambler is not used in 10 Mbps mode.
Descrambler Bypass
The descrambler can be bypassed by setting the bypass scrambler/descrambler bit in the PHY MI
serial port Configuration 1 register. When this bit is set, the data bypasses the descrambler and goes
directly from the TP receiver to the 4B5B decoder.
7.7.7
Twisted Pair Transmitter
Transmitter - 100 Mbps
The TX transmitter consists of MLT-3 encoder, waveform generator and line driver.
The MLT-3 encoder converts the NRZ data from the scrambler into a three level MLT-3 code required
by IEEE 802.3. MLT-3 coding uses three levels and converts 1's to transitions between the three levels,
and converts 0's to no transitions or changes in level.
The purpose of the waveform generator is to shape the transmit output pulse. The waveform generator
takes the MLT-3 three level encoded waveform and uses an array of switched current sources to
control the rise/fall time and level of the signal at the Output. The output of the switched current
sources then goes through a low pass filter in order to "smooth" the current output and remove any
high frequency components. In this way, the waveform generator preshapes the output waveform
transmitted onto the twisted pair cable to meet the pulse template requirements outlined in IEEE 802.3.
The waveform generator eliminates the need for any external filters on the TP transmit output.
The line driver converts the shaped and smoothed waveform to a current output that can drive 100
meters of category 5 unshielded twisted pair cable or 150 Ohm shielded twisted pair cable.
Transmitter - 10 Mbps
The transmitter operation in 10 Mbps mode is much different than the 100 Mbps transmitter. Even so,
the transmitter still consists of a waveform generator and line driver.
The purpose of the waveform generator is to shape the output transmit pulse. The waveform generator
consists of a ROM, DAC, dock generator, and filter. The DAC generates a stair-stepped representation
of the desired output waveform. The stairstepped DAC output then goes through a low pass filter in
order to "smooth' the DAC output and remove any high frequency components. The DAC values are
determined from the ROM outputs; the ROM contents are chosen to shape the pulse to the desired
template and are clocked into the DAC at high speed by the clock generator. In this way, the waveform
generator preshapes the output waveform to be transmitted onto the twisted pair cable to meet the
pulse template requirements outlined in IEEE 802.3 Clause 14 and also shown in Figure 7.4. The
waveshaper replaces and eliminates external filters on the TP transmit output.
The line driver converts the shaped and smoothed waveform to a current output that can drive 100
meters of category 3/4/5 100 Ohm unshielded twisted pair cable or 150 Ohm shielded twisted pair
cable tied directly to the TP output pins without any external filters. During the idle period, no output
signal is transmitted on the TP outputs (except link pulse).
SMSC LAN91C111-REV B
39
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
N
B
1.0
0.8
P
H
0.6
D
0.4
C
I
O
E
Voltage (V)
0.2
0.0
Q
A
M
F
R
J
-0.2
S
-0.4
U
LK
-0.6
W
V
-0.8
G
-1.0
0
10
20
30
40
50
60
70
80
90
100
T
10
TIME (ns)
Figure 7.4 TP Output Voltage Template - 10 MBPS
REFERENCE
TIME (NS) INTERNAL MAU
VOLTAGE (V)
A
0
0
B
15
1.0
C
15
0.4
D
25
0.55
E
32
0.45
F
39
0
G
57
-1.0
H
48
0.7
I
67
0.6
J
89
0
K
74
-0.55
L
73
-0.55
M
61
0
N
85
1.0
O
100
0.4
P
110
0.75
Revision 1.8 (07-13-05)
40
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
REFERENCE
TIME (NS) INTERNAL MAU
VOLTAGE (V)
Q
111
0.15
R
111
0
S
111
-0.15
T
110
-1.0
U
100
-0.3
V
110
-0.7
W
90
-0.7
Transmit Level Adjust
The transmit output current level is derived from an internal reference voltage and the external resistor
on RBIAS pin. The transmit level can be adjusted with either (1) the external resistor on the RBIAS
pin, or (2) the four transmit level adjust bits in the PHY Ml serial port Configuration 1 register as shown
in Table 7.2. The adjustment range is approximately -14% to +16% in 2% steps.
Table 7.2 Transmit Level Adjust
TLVL[3:0]
GAIN
0000
1.16
0001
1.14
0010
1.12
0011
1.10
0100
1.08
0101
1.06
0110
1.04
0111
1.02
1000
1.00
1001
0.98
1010
0.96
1011
0.94
1100
0.92
1101
0.90
1110
0.88
1111
0.86
Transmit Rise and Fall Time Adjust
The transmit output rise and fall time can be adjusted with the two transmit rise/fall time adjust bits in
the PHY Ml serial port Configuration 1. The adjustment range is -0.25ns to +0.5ns in 0.25ns steps.
SMSC LAN91C111-REV B
41
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
STP (150 Ohm) Cable Mode
The transmitter can be configured to drive 150 Ohm shielded twisted pair cable. The STP mode can
be selected by appropriately setting the cable type select bit in the PHY MI serial port Configuration 1
register. When STP mode is enabled, the output current is automatically adjusted to comply with IEEE
802.3 levels.
Transmit Disable
The TP transmitter can be disabled by setting the transmit disable bit in the PHY Ml serial port
Configuration 1 register. When the transmit disable bit is set, the TP transmitter is forced into the idle
state, no data is transmitted, no link pulses are transmitted, and internal loopback is disabled.
Transmit Powerdown
The TP transmitter can be powered down by setting the transmit powerdown bit in the PHY Ml serial
port Configuration 1 register. When the transmit powerdown bit is set, the TP transmitter is powered
down, the TP transmit outputs are high impedance, and the rest of the LAN91C111 operates normally.
7.7.8
Twisted Pair Receiver
Receiver - 100 Mbps
The TX receiver detects input signals from the twisted pair input and converts it to a digital data bit
stream ready for dock and data recovery. The receiver can reliably detect data from a 100BASE-TX
transmitter that has been passed through 0-100 meters of 100-Ohm category 5 UTP or 150 Ohm STP.
The TX receiver consists of an adaptive equalizer, baseline wander correction circuit, comparators, and
MLT-3 decoder. The TP inputs first go to an adaptive equalizer. The adaptive equalizer compensates
for the low pass characteristic of the cable, and it has the ability to adapt and compensate for 0-100
meters of category 5, 100 Ohm UTP or 150 Ohm STP twisted pair cable. The baseline wander
correction circuit restores the DC component of the input waveform that was removed by external
transformers. The comparators convert the equalized signal back to digital levels and are used to
qualify the data with the squelch circuit. The MLT-3 decoder takes the three level MLT-3 digital data
from the comparators and converts it to back to normal digital data to be used for dock and data
recovery.
Receiver - 10 Mbps
The 10 Mbps receiver is able to detect input signals from the twisted pair cable that are within the
template shown in Figure 7.5. The inputs are biased by internal resistors. The TP inputs pass through
a low pass filter designed to eliminate any high frequency noise on the input. The output of the receive
filter goes to two different types of comparators, squelch and zero crossing. The squelch comparator
determines whether the signal is valid, and the zero crossing comparator is used to sense the actual
data transitions once the signal is determined to be valid. The output of the squelch comparator goes
to the squelch circuit and is also used for link pulse detection, SOI detection, and reverse polarity
detection; the output of the zero crossing comparator is used for clock and data recovery in the
Manchester decoder.
Revision 1.8 (07-13-05)
42
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
a. Short Bit
3.1V
Slope 0.5 V/ ns
585mV
585 mV sin (
*t/PW)
PW
0
b. Long Bit
3.1V
Slope 0.5 V/ ns
585mV
585 mV sin (2 * t/PW)
585 mV sin [2
3PW/4
PW/4
0
(t - PW/2)/PW]
PW
Figure 7.5 TP Input Voltage Template -10MBPS
TP Squelch - 100 Mbps
The squelch block determines if the TP input contains valid data. The 100 Mbps TP squelch is one
of the criteria used to determine link integrity. The squelch comparators compare the TP inputs against
fixed positive and negative thresholds, called squelch levels. The output from the squelch comparator
goes to a digital squelch circuit which determines if the receive input data on that channel is valid. If
the data is invalid, the receiver is in the squelched state. If the input voltage exceeds the squelch
levels at least 4 times with alternating polarity within a 10 µS interval, the data is considered to be
valid by the squelch circuit and the receiver now enters into the unsquelch state. In the unsquelch
state, the receive threshold level is reduced by approximately 30% for noise immunity reasons and is
called the unsquelch level. When the receiver is in the unsquelch state, then the input signal is
deemed to be valid. The device stays in the unsquelch state until loss of data is detected. Loss of
data is detected if no alternating polarity unsquelch transitions are detected during any 10 µS interval.
When the loss of data is detected, the receive squelch is turned on again.
TP Squelch, 10 Mbps
The TP squelch algorithm for 10 Mbps mode is identical to the 100 Mbps mode except, (1) the 10
Mbps TP squelch algorithm is not used for link integrity but to sense the beginning of a packet, (2) the
receiver goes into the unsquelch state if the input voltage exceeds the squelch levels for three bit times
with alternating polarity within a 50-250 nS interval, (3) the receiver goes into the squelch state when
idle is detected, (4) unsquelch detection has no affect on link integrity, link pulses are used for that in
10 Mbps mode, (5) start of packet is determined when the receiver goes into the unsquelch state an
a CRS100 is asserted, and (6) the receiver meets the squelch requirements defined in IEEE 802.3
Clause 14.
SMSC LAN91C111-REV B
43
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Equalizer Disable
The adaptive equalizer can be disabled by setting the equalizer disable bit in the PHY Ml serial port
Configuration 1 register. When disabled, the equalizer is forced into the response it would normally
have if zero cable length was detected.
Receive Level Adjust
The receiver squelch and unsquelch levels can be lowered by 4.5 dB by setting the receive level adjust
bit in the PHY Ml serial port Configuration 1 register. By setting this bit, the device may be able to
support longer cable lengths.
7.7.9
Collision
100 Mbps
Collision occurs whenever transmit and receive occur simultaneously while the device is in Half
Duplex.
Collision is sensed whenever there is simultaneous transmission (packet transmission on TPO±) and
reception (non-idle symbols detected on TP input). When collision is detected, the MAC is notified.
Once collision starts, the receive and transmit packets that caused the collision are terminated by their
respective MACs until the responsible MACs terminate the transmission, the PHY continues to pass
the data on.
The collision function is disabled if the device is in the Full Duplex mode, is in the Link Fail State, or
if the device is in the diagnostic loopback mode.
10 Mbps
Collision in 10Mbps mode is identical to the 100Mbps mode except, (1) reception is determined by the
10Mbps squelch criteria, (2) data being passed to the MAC are forced to all 0's, (3) MAC is notified of
the collision when the SQE test is performed, (4) MAC is notified of the collision when the jabber
condition has been detected.
Collision Test
The MAC and PHY collision indication can be tested by setting the collision test register bit in the PHY
MI serial port Control register. When this bit is set, internal TXEN from the MAC is looped back onto
COL and the TP outputs are disabled.
7.7.10
Start of Packet
100 Mbps
Start of packet for 100 Mbps mode is indicated by a unique Start of Stream Delimiter (referred to as
SSD). The SSD pattern consists of the two /J/K/ 5B symbols inserted at the beginning of the packet
in place of the first two preamble symbols, as defined in IEEE 802.3 Clause 24.
The transmit SSD is generated by the 4B5B encoder and the /J/K/ symbols are inserted by the 4B5B
encoder at the beginning of the transmit data packet in place of the first two 5B symbols of the
preamble.
The receive pattern is detected by the 4B5B decoder by examining groups of 10 consecutive code bits
(two 5B words) from the descrambler. Between packets, the receiver will be detecting the idle pattern,
which is 5B /I/ symbols. While in the idle state, the MAC is notified that no data/invalid data is received.
If the receiver is in the idle state and 10 consecutive code bits from the receiver consist of the /J/K/
symbols, the start of packet is detected, data reception is begun, the MAC is notified that valid data is
received, and 5/5/ symbols are substituted in place of the /J/K/ symbols.
If the receiver is in the idle state and 10 consecutive code bits from the receiver consist of a pattern
that is neither /I/I/ nor /J/K/ symbols but contains at least 2 non contiguous 0's, then activity is detected
but the start of packet is considered to be faulty and a False Carrier Indication (also referred to as bad
Revision 1.8 (07-13-05)
44
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
SSD) is signaled to the controller interface. When False Carrier is detected, the MAC is notified of
false carrier and invalid received, and the bad SSD bit is set in the PHY Ml serial port Status Output
register. Once a False Carrier Event is detected, the idle pattern (two /I/I/ symbols) must be detected
before any new SSD's can be sensed.
If the receiver is in the idle state and 10 consecutive code bits from the receiver consist of a pattern
that is neither /l/l/ nor /J/K/ symbols but does not contain at least 2 non-contiguous 0's, the data is
ignored and the receiver stays in the idle state.
10 Mbps
Since the idle period in 10 Mbps mode is defined to be the period when no data is present on the TP
inputs, then the start of packet for 10 Mbps mode is detected when valid data is detected by the TP
squelch circuit. When start of packet is detected, carrier sense signal at internal MII is asserted as
described in the Controller Interface section. Refer to the TP squelch section for 10 Mbps mode for
the algorithm for valid data detection.
7.7.11
End of Packet
100 Mbps
End of packet for 100 Mbps mode is indicated by the End of Stream Delimiter (referred to as ESD).
The ESD pattern consists of the two /T/R/ 4B5B symbols inserted after the end of the packet, as
defined in IEEE 802.3 Clause 24.
The transmit ESD is generated by the 4B5B encoder and the /T/R/ symbols are inserted by the 4B5B
encoder after the end of the transmit data packet.
The receive ESD pattern is detected by the 4B5B decoder by examining groups of 10 consecutive
code bits (two 5B words) from the descrambler during valid packet reception to determine if there is
an ESD.
If the 10 consecutive code bits from the receiver during valid packet reception consist of the /T/R/
symbols, the end of packet is detected, data reception is terminated, the MAC is notified of valid data
received, and /I/I/ symbols are substituted in place of the /T/R/ symbols.
If 10 consecutive code bits from the receiver during valid packet reception do not consist of /T/R/
symbols but consist of /I/I/ symbols instead, then the packet is considered to have been terminated
prematurely and abnormally. When this premature end of packet condition is detected, the MAC is
notified of invalid data received for the nibble associated with the first /I/ symbol. Premature end of
packet condition is also indicated by setting the bad ESD bit in the PHY Ml serial port Status Output
register.
10 Mbps
The end of packet for 10 Mbps mode is indicated with the SOI (Start of Idle) pulse. The SOI pulse is
a positive pulse containing a Manchester code violation inserted at the end of every packet.
The transmit SOI pulse is generated by the TP transmitter and inserted at the end of the data packet
after TXEN is deasserted. The transmitted SOI output pulse at the TP output is shaped by the transmit
waveshaper to meet the pulse template requirements specified in IEEE 802.3 Clause 14 and shown
in Figure 7.6.
The receive SOI pulse is detected by the TP receiver by sensing missing data transitions. Once the
SOI pulse is detected, data reception is ended and the MAC is notified of no data/invalid data received.
SMSC LAN91C111-REV B
45
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
0 BT
4.5 BT
3.1 V
0.5 V/ns
0.25 BT
2.25 BT
585 mV
6.0 BT
+50 mV
-50 mV
45.0 BT
585 mV sin(2 * * (t/1BT))
0 t 0.25 BT and
2.25 t 2.5 BT
-3.1 V
2.5 BT
4.5 BT
Figure 7.6 SOI Output Voltage Template - 10MBPS
7.7.12
Link Integrity & Autonegotiation
General
The LAN91C111 can be configured to implement either the standard link integrity algorithms or the
AutoNegotiation algorithm.
The standard link integrity algorithms are used solely to establish an active link to and from a remote
device. There are different standard link integrity algorithms for 10 and 100 Mbps modes. The
AutoNegotiation algorithm is used for two purposes: (1) To automatically configure the device for either
10/100 Mbps and Half/Full Duplex modes, and (2) to establish an active link to and from a remote
device. The standard link integrity and AutoNegotiation algorithms are described below.
AutoNegotiation is only specified for 100BASE-TX and 10BASE-T operation.
10BASE-T Link Integrity Algorithm - 10Mbps
The LAN91C111 uses the same 10BASE-T link integrity algorithm that is defined in IEEE 802.3 Clause
14. This algorithm uses normal link pulses, referred to as NLP's and transmitted during idle periods,
to determine if a device has successfully established a link with a remote device (called Link Pass
State). The transmit link pulse meets the template defined in IEEE 802.3 Clause 14 and shown in
Figure 7.7. Refer to IEEE 802.3 Clause 14 for more details if needed.
Revision 1.8 (07-13-05)
46
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
1.3
BT
0
BT
3.1 V
0.5 V/ns
585 mV
0.5
BT 0.6
BT
2.0
BT
300 mV
4.0
BT
+50 mV
+50 mV
-50 mV
0.25
BT
200 mV
-50 mV
4.0
BT
42.0
BT
-3.1 V
0.85
BT
2.0
BT
Figure 7.7 Link Pulse Output Voltage Template - NLP, FLP
100BASE-TX Link Integrity Algorithm -100Mbps
Since 100BASE-TX is defined to have an active idle signal, then there is no need to have separate
link pulses like those defined for 10BASE-T. The LAN91C111 uses the squelch criteria and
descrambler synchronization algorithm on the input data to determine if the device has successfully
established a link with a remote device (called Link Pass State). Refer to IEEE 802.3 for both of these
algorithms for more details.
AutoNegotiation Algorithm
As stated previously, the AutoNegotiation algorithm is used for two purposes: (1) To automatically
configure the device for either 10/100 Mbps and Half/ Full Duplex modes, and (2) to establish an active
link to and from a remote device. The AutoNegotiation algorithm is the same algorithm that is defined
in IEEE 802.3 Clause 28. AutoNegotiation uses a burst of link pulses, called fast link pulses and
referred to as FLP'S, to pass up to 16 bits of signaling data back and forth between the LAN91C111
and a remote device. The transmit FLP pulses meet the templated specified in IEEE 802.3 and shown
in Figure 7.7. A timing diagram contrasting NLP's and FLP's is shown in Figure 7.8.
SMSC LAN91C111-REV B
47
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
a.) Normal Link Pulse (NLP)
TPO±
b.) Fast Link Pulse (FLP)
TPO±
D0
Clock
D1
Clock
Data
D2
Clock
Data
D3
Clock
Data
D14
Clock
Data
D15
Clock
Data
Clock
Data
Figure 7.8 NLP VS. FLP Link Pulse
The AutoNegotiation algorithm is initiated by any of these events: (1) AutoNegotiation enabled, (2) a
device enters the Link Fail State, (3) AutoNegotiation Reset. Once a negotiation has been initiated,
the LAN91C111 first determines if the remote device has AutoNegotiation capability. If the remote
device is not AutoNegotiation capable and is just transmitting either a 10BASE-T or 100BASE-TX
signal, the LAN91C111 will sense that and place itself in the correct mode. If the LAN91C111 detects
FLP's from the remote device, then the remote device is determined to have AutoNegotiation capability
and the device then uses the contents of the Ml serial port AutoNegotiation Advertisement register and
FLP's to advertise its capabilities to a remote device. The remote device does the same, and the
capabilities read back from the remote device are stored in the PHY Ml serial port AutoNegotiation
Remote End Capability register. The LAN91C111 negotiation algorithm then matches it's capabilities
to the remote device's capabilities and determines what mode the device should be configured to
according to the priority resolution algorithm defined in IEEE 802.3 Clause 28. Once the negotiation
process is completed, the LAN91C111 then configures itself for either 10 or 100 Mbps mode and either
Full or Half Duplex modes (depending on the outcome of the negotiation process), and it switches to
either the 100BASETX or 10BASE-T link integrity algorithms (depending on which mode was enabled
by AutoNegotiation). Refer to IEEE 802.3 Clause 28 for more details.
AutoNegotiation Outcome Indication
The outcome or result of the AutoNegotiation process is stored in the speed detect and duplex detect
bits in the PHY MI serial port Status Output register.
AutoNegotiation Status
The status of the AutoNegotiation process can be monitored by reading the AutoNegotiation
acknowledgement bit in the Ml serial port Status register. The Ml serial port Status register contains
a single AutoNegotiation acknowledgement bit which indicates when an AutoNegotiation has been
initiated and successfully completed.
AutoNegotiation Enable
The AutoNegotiation algorithm can be enabled by setting both the ANEG bit in the MAC Receive/PHY
Control Register and the ANEG_EN bit in the MI PHY Register 0 (Control register). Clearing either of
these two bits will turn off AutoNegotiation mode. When the AutoNegotiation algorithm is enabled, the
Revision 1.8 (07-13-05)
48
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
device halts all transmissions including link pulses for 1200-1500 ms, enters the Link Fail State, and
restarts the negotiation process. When AutoNegotiation mode is turned on or reset, software driver
should wait for at least 1500ms to read the ANEG_ACK bit in the MI PHY Status Register to determine
whether the AutoNegotiation process has been completed. When the ANEG bit in the Receive/PHY
Control Register is cleared, AutoNegotiation algorithm is disabled, the selection of 10/100 Mbps mode
and duplex mode is determined by the SPEED bit and the DPLX bit in the MAC Receive/PHY Control
register. When the ANEG bit in the Receive/PHY Control Register is set and the ANEG_EN bit in the
MI PHY Register 0 (Control Register) is cleared, AutoNegotiation algorithm is disabled, the selection
of 10/100 Mbps mode and duplex mode is determined by the SPEED bit and the DPLX bit in the MI
PHY Register 0 (Control Register).
AutoNegotiation Reset
The AutoNegotiation algorithm can be initiated at any time by setting the AutoNegotiation reset bit in
the PHY MI serial port Control register.
Link Disable
The link integrity function can be disabled by setting the link disable bit in the PHY Ml serial port
Configuration 1 register. When the link integrity function is disabled, the device is forced into the Link
Pass state, configures itself for Half/Full Duplex based on the value of the duplex bit in the PHY MI
serial port Control register, configures itself for 100/10 Mbps operation based on the values of the
speed bit in the Ml serial port Control register, and continues to transmit NLP'S or TX idle patterns,
depending on whether the device is in 10 or 100 Mbps mode.
7.7.13
Jabber
100 Mbps
Jabber function is disabled in the 100 Mbps mode.
10 Mbps
Jabber condition occurs when the transmit packet exceeds a predetermined length. When jabber is
detected, the TP transmit outputs are forced to the idle state, collision is asserted, and register bits in
the PHY Ml serial port Status and Status Output registers are set.
Jabber Disable
The jabber function can be disabled by setting the jabber disable bit in the PHY MI serial port
Configuration 2 register.
7.7.14
Receive Polarity Correction
100 Mbps
No polarity detection or correction is needed in 100Mbps mode.
10 Mbps
The polarity of the signal on the TP receive input is continuously monitored. If either 3 consecutive
link pulses or one SOI pulse indicates incorrect polarity on the TP receive input, the polarity is internally
determined to be incorrect, and a reverse polarity bit is set in the PHY Ml serial port Status Output
register.
The LAN91C111 will automatically correct for the reverse polarity condition provided that the
autopolarity feature is not disabled.
Autopolarity Disable
The autopolarity feature can be disabled by setting the autopolarity disable bit in the PHY MI serial
port Configuration 2 register.
SMSC LAN91C111-REV B
49
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
7.7.15
Full Duplex Mode
100 Mbps
Full Duplex mode allows transmission and reception to occur simultaneously. When Full Duplex mode
is enabled, collision is disabled.
The device can be either forced into Half or Full Duplex mode, or the device can detect either Half or
Full Duplex capability from a remote device and automatically place itself in the correct mode.
The device can be forced into the Full or Half Duplex modes by either setting the duplex bit in the MI
serial port Control register.
The device can automatically configure itself for Full or Half Duplex modes by using the
AutoNegotiation algorithm to advertise and detect Full and Half Duplex capabilities to and from a
remote terminal. All of this is described in detail in the Link Integrity and AutoNegotiation section.
10 Mbps
Full Duplex in 10 Mbps mode is identical to the 100 Mbps mode.
100/10 Mbps SELECTION
General
The device can be forced into either the 100 or 10 Mbps mode, or the device also can detect 100 or
10 Mbps capability from a remote device and automatically place itself in the correct mode.
The device can be forced into either the 100 or 10 Mbps mode by setting the speed select bit in the
PHY MI serial port Control register assuming AutoNegotiation is not enabled.
The device can automatically configure itself for 100 or 10 Mbps mode by using the AutoNegotiation
algorithm to advertise and detect 100 and 10 Mbps capabilities to and from a remote terminal. All of
this is described in detail in the Link Integrity & AutoNegotiation section.
7.7.16
Loopback
Diagnostic Loopback
A diagnostic loopback mode can also be selected by setting the loopback bit in the MI serial port
Control register. When diagnostic loopback is enabled, transmit data at internal MII is looped back
onto receive data output at internal MII, transmit enable signal is looped back onto carrier sense output
at internal MII, the TP receive and transmit paths are disabled, the transmit link pulses are halted, and
the Half/Full Duplex modes do not change.
7.7.17
PHY Powerdown
The internal PHY of LAN91C111 can be powered down by setting the powerdown bit in the PHY Ml
serial port Control register. In powerdown mode, the TP outputs are in high impedance state, all
functions are disabled except the PHY Ml serial port, and the power consumption is reduced to a
minimum. To restore PHY to normal power mode, set the PDN bit in PHY MI Register 0 to 0. The PHY
is then in isolation mode (MII_DIS bit is set); This MII_DIS bit is needed to be cleared. The device is
guaranteed to be ready for normal operation 500mS after powerdown is de-asserted.
7.7.18
PHY Interrupt
The LAN91C111 PHY has interrupt capability. The interrupt is triggered by certain output status bits
(also referred to as interrupt bits) in the serial port. R/LT bits are read bits that latch on transition.
R/LT bits are also interrupt bits if they are not masked out with the Mask register bits. Interrupt bits
automatically latch themselves into their register locations and assert the interrupt indication when they
change state. Interrupt bits stay latched until they are read. When interrupt bits are read, the interrupt
indication is deasserted and the interrupt bits that caused the interrupt to happen are updated to their
Revision 1.8 (07-13-05)
50
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
current value. Each interrupt bit can be individually masked and subsequently be removed as an
interrupt bit by setting the appropriate mask register bits in the Mask register.
lnterrupt indication is done in two ways: (1) MDINT bit in Interrupt Status Register, (2) INT bit in the
PHY Ml Serial Port Status Output register. The INT bit is an active high interrupt register bit that
resides in the PHY MI Serial Port Status Output register.
7.8
Reset
The chip (MAC & PHY) performs an internal system reset when either (1) the RESET pin is asserted
high for at least 100ns, (2) writing “1” to the SOFT_RST bit in the Receive Control Register, this reset
bit is not a self-clearing bit, reset can be terminated by writing the bit low. It programs all registers to
their default value. When reset is initiated by (1) and the EEPROM is presented and enabled, the
controller will load the EEPROM to obtain the following configurations: 1) Configuration Register, 2)
BASE Register, or/and 3) MAC Address. The internal MAC is not a power on reset device, thus reset
is required after power up to ensure all register bits are in default state.
The internal PHY is reset when either (1) VDD is applied to the device, (2) the RST bit is set in the
PHY Ml serial port Control register, this reset bit is a self-clearing bit, and the PHY will return a “1” on
reads to this bit until the reset is completed, 3) the RESET pin is asserted high, (4) the SOFT_RST
bit is set high and then cleared. When reset is initiated by (1) or (2), an internal power-on reset pulse
is generated which resets all internal circuits, forces the PHY Ml serial port bits to their default values,
and latches in new values for the MI address. After the power-on reset pulse has finished, the reset
bit in the PHY Ml serial port Control registers cleared and the device is ready for normal operation.
When reset is initiated by (3), the same procedure occurs except the device stays in the reset state
as long as the RESET pin is held high. The internal PHY is guaranteed to be ready for normal
operation 50 mS after the reset pin was de-asserted or the reset bit is set. Software driver requires
to wait for 50mS after setting the RST bit to high to access the internal PHY again.
SMSC LAN91C111-REV B
51
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Revision 1.8 (07-13-05)
52
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Chapter 8 MAC Data Structures and Registers
8.1
Frame Format In Buffer Memory
The frame format in memory is similar for the Transmit and Receive areas. The first word is reserved
for the status word. The next word is used to specify the total number of bytes, and it is followed by
the data area. The data area holds the frame itself. By default, the last byte in the receive frame format
is followed by the CRC, and the Control byte follows the CRC.
RAM
OFFSET
(DECIMAL)
bit0
bit15
2nd Byte
1st Byte
0
2
STATUS WORD
BYTE COUNT (always even)
RESERVED
4
DATA AREA
CRC (4 BYTES)
2046 Max
CONTROL BYTE
LAST DATA BYTE (if odd)
Last Byte
Figure 8.1 Data Frame Format
TRANSMIT PACKET
RECEIVE PACKET
STATUS WORD
Written by CSMA upon transmit
completion (see Status Register)
Written by CSMA upon receive
completion (see RX Frame Status
Word)
BYTE COUNT
Written by CPU
Written by CSMA
DATA AREA
Written/modified by CPU
Written by CSMA
CONTROL BYTE
Written by CPU to control odd/even
data bytes
Written by CSMA; also has odd/even
bit
BYTE COUNT - Divided by two, it defines the total number of words including the STATUS WORD,
the BYTE COUNT WORD, the DATA AREA, the CRC, and the CONTROL BYTE. The CRC is not
included if the STRIP_CRC bit is set. The maximum number of bytes in a RAM page is 2048 bytes.
SMSC LAN91C111-REV B
53
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
The receive byte count always appears as even; the ODDFRM bit of the receive status word indicates
if the low byte of the last word is relevant.
The transmit byte count least significant bit will be assumed 0 by the controller regardless of the value
written in memory.
DATA AREA - The data area starts at offset 4 of the packet structure and can extend up to 2043 bytes.
The data area contains six bytes of DESTINATION ADDRESS followed by six bytes of SOURCE
ADDRESS, followed by a variable-length number of bytes. On transmit, all bytes are provided by the
CPU, including the source address. The LAN91C111 does not insert its own source address. On
receive, all bytes are provided by the CSMA side.
The 802.3 Frame Length word (Frame Type in Ethernet) is not interpreted by the LAN91C111. It is
treated transparently as data both for transmit and receive operations.
CONTROL BYTE - For transmit packets the CONTROL BYTE is written by the CPU as:
X
X
ODD
CRC
0
0
0
0
ODD - If set, indicates an odd number of bytes, with the last byte being right before the CONTROL
BYTE. If clear, the number of data bytes is even and the byte before the CONTROL BYTE is not
transmitted.
CRC - When set, CRC will be appended to the frame. This bit has meaning only if the NOCRC bit in
the TCR is set.
For receive packets the CONTROL BYTE is written by the controller as:
0
1
ODD
0
0
0
0
0
ODD - If set, indicates an odd number of bytes, with the last byte being right before the CONTROL
BYTE. If clear, the number of data bytes is even and the byte before the CONTROL BYTE should be
ignored.
8.2
Receive Frame Status
This word is written at the beginning of each receive frame in memory. It is not available as a register.
HIGH
BYTE
ALGN
ERR
BROD
CAST
BAD
CRC
LOW
BYTE
ODD
FRM
TOOLNG
TOO
SHORT
HASH VALUE
Reserved
5
4
3
MULT
CAST
2
1
0
ALGNERR - Frame had alignment error.
Revision 1.8 (07-13-05)
54
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
BROADCAST - Receive frame was broadcast. When a broadcast packet is received, the MULTCAST
bit may be also set on the status word in addition to the BRODCAST bit. The software implement may
just ignore the MULTCAST bit if for BRODCAST packet.
BADCRC - Frame had CRC error, or RX_ER was asserted during reception.
ODDFRM - This bit when set indicates that the received frame had an odd number of bytes.
TOOLNG - Frame length was longer than 802.3 maximum size (1518 bytes on the cable).
TOOSHORT - Frame length was shorter than 802.3 minimum size (64 bytes on the cable).
HASH VALUE - Provides the hash value used to index the Multicast Registers. Can be used by
receive routines to speed up the group address search. The hash value consists of the six most
significant bits of the CRC calculated on the Destination Address, and maps into the 64 bit multicast
table. Bits 5,4,3 of the hash value select a byte of the multicast table, while bits 2,1,0 determine the
bit within the byte selected. Examples of the address mapping:
ADDRESS
HASH VALUE 5-0
ED 00 00 00 00 00
0D 00 00 00 00 00
01 00 00 00 00 00
2F 00 00 00 00 00
000 000
010 000
100 111
111 111
MULTICAST TABLE BIT
MT-0
MT-2
MT-4
MT-7
bit
bit
bit
bit
0
0
7
7
MULTCAST - Receive frame was multicast. If hash value corresponds to a multicast table bit that is
set, and the address was a multicast, the packet will pass address filtering regardless of other filtering
criteria.
8.3
I/O Space
The base I/O space is determined by the IOS0-IOS2 inputs and the EEPROM contents. To limit the
I/O space requirements to 16 locations, the registers are assigned to different banks. The last word of
the I/O area is shared by all banks and can be used to change the bank in use. Registers are
described using the following convention:
OFFSET
HIGH
BYTE
LOW
BYTE
NAME
TYPE
SYMBOL
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8
X
X
X
X
X
X
X
X
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
X
X
X
X
X
X
X
X
FFSET - Defines the address offset within the IOBASE where the register can be accessed at,
provided the bank select has the appropriate value.
The offset specifies the address of the even byte (bits 0-7) or the address of the complete word.
The odd byte can be accessed using address (offset + 1).
Some registers (like the Interrupt Ack., or like Interrupt Mask) are functionally described as two eight
bit registers, in that case the offset of each one is independently specified.
SMSC LAN91C111-REV B
55
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Regardless of the functional description, all registers can be accessed as doublewords, words or bytes.
The default bit values upon hard reset are highlighted below each register.
Table 8.1 Internal I/O Space Mapping
0
2
4
6
8
A
C
E
BANK0
TCR
EPH STATUS
RCR
COUNTER
MIR
RPCR
RESERVED
BANK
BANK1
CONFIG
BASE
IA0-1
IA2-3
IA4-5
GENERAL PURPOSE
CONTROL
BANK
BANK2
MMU COMMAND
PNR
FIFO PORTS
POINTER
DATA
DATA
INTERRUPT
BANK
BANK3
MT0-1
MT2-3
MT4-5
MT6-7
MGMT
REVISION
ERCV
BANK
A special BANK (BANK7) exists to support the addition of external registers.
8.4
HIGH
BYTE
Bank Select Register
OFFSET
NAME
TYPE
SYMBOL
E
BANK SELECT REGISTER
READ/WRITE
BSR
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
0
0
1
1
0
0
1
1
BS2
BS1
BS0
0
0
0
LOW
BYTE
X
X
X
X
X
BS2, BS1, BS0 Determine the bank presently in use. This register is always accessible and is used
to select the register bank in use.
The upper byte always reads as 33h and can be used to help determine the I/O location of the
LAN91C111.
The BANK SELECT REGISTER is always accessible regardless of the value of BS0-2
Note: The bank select register can be accessed as a doubleword at offset 0x0Ch, as a word at offset
0x0Eh, or as a byte at offset 0x0Eh, A doubleword write to offset 0x0Ch will write the BANK
SELECT REGISTER but will not write the registers 0x0Ch and 0x0Dh, but will only write to
register 0x0Eh
BANK 7 has no internal registers other than the BANK SELECT REGISTER itself. On valid cycles
where BANK7 is selected (BS0=BS1=BS2=1), and A3=0, nCSOUT is activated to facilitate
implementation of external registers.
Note: BANK7 does not exist in LAN91C9x devices. For backward S/W compatibility BANK7 accesses
should be done if the Revision Control register indicates the device is the LAN91C111.
Bank 7 is a new register Bank to the SMSC LAN91C111 device. This bank has extended registers that
allow the extended feature set of the SMSC LAN91C111.
Revision 1.8 (07-13-05)
56
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
8.5
Bank 0 - Transmit Control Register
OFFSET
NAME
TYPE
SYMBOL
0
TRANSMIT CONTROL
REGISTER
READ/WRITE
TCR
This register holds bits programmed by the CPU to control some of the protocol transmit options.
HIGH
BYTE
LOW
BYTE
SWFDUP
Reserved
EPH
LOOP
STP
SQET
FDUPLX
MON_
CSN
Reserved
NOCRC
0
0
0
0
0
0
0
0
PAD_EN
Reserved
Reserved
Reserved
Reserved
FORCOL
LOOP
TXENA
0
0
0
0
0
0
0
0
SWFDUP - Enables Switched Full Duplex mode. In this mode, transmit state machine is inhibited from
recognizing carrier sense, so deferrals will not occur. Also inhibits collision count, therefore, the
collision related status bits in the EPHSR are not valid (CTR_ROL, LATCOL, SQET, 16COL, MUL COL,
and SNGL COL). Uses COL100 as flow control, limiting backoff and jam to 1 clock each before interframe gap, then retry will occur after IFG. If COL100 is active during preamble, full preamble will be
output before jam. When SWFDUP is high, the values of FDUPLX and MON_CSN have no effect.
EPH_LOOP - Internal loopback at the EPH block. Serial data is internally looped back when set.
Defaults low. When EPH_LOOP is high the following transmit outputs are forced inactive: TXD0-TXD3
= 0h, TXEN100 = 0. The following and external inputs are blocked: CRS100=0, COL100=0, RX_DV=
RX_ER=0.
STP_SQET - STP_SQET - Stop transmission on SQET error. If this bit is set, LAN91C111 will stop
and disable the transmitter on SQE test error. If the external SQET generator on the network generates
the SQET pulse during the IPG (Inter Frame Gap), this bit will not be set and subsequent transmits
will occur as in the case of implementing “Auto Release” for multiple transmit packets. If this bit is
cleared, then the SQET bit in the EPH Status register will be cleared. Defaults low.
FDUPLX - When set the LAN91C111 will cause frames to be received if they pass the address filter
regardless of the source for the frame. When clear the node will not receive a frame sourced by itself.
This bit does not control the duplex mode operation, the duplex mode operation is controlled by the
SWFDUP bit.
MON_CSN - When set the LAN91C111 monitors carrier while transmitting. It must see its own carrier
by the end of the preamble. If it is not seen, or if carrier is lost during transmission, the transmitter
aborts the frame without CRC and turns itself off and sets the LOST CARR bit in the EPHSR. When
this bit is clear the transmitter ignores its own carrier. Defaults low. Should be 0 for MII operation.
NOCRC - Does not append CRC to transmitted frames when set. Allows software to insert the desired
CRC. Defaults to zero, namely CRC inserted.
PAD_EN - When set, the LAN91C111 will pad transmit frames shorter than 64 bytes with 00. For TX,
CPU should write the actual BYTE COUNT before padded by the LAN91C111 to the buffer RAM,
excludes the padded 00. When this bit is cleared, the LAN91C111 does not pad frames.
FORCOL - When set, the FORCOL bit will force a collision by not deferring deliberately. This bit is set
and cleared only by the CPU. When TXENA is enabled with no packets in the queue and while the
FORCOL bit is set, the LAN91C111 will transmit a preamble pattern the next time a carrier is seen on
the line. If a packet is queued, a preamble and SFD will be transmitted. This bit defaults low to normal
SMSC LAN91C111-REV B
57
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
operation. NOTE: The LATCOL bit in the EPHSR, setting up as a result of FORCOL, will reset TXENA
to 0. In order to force another collision, TXENA must be set to 1 again.
LOOP - Loopback. General purpose output port used to control the LBK pin. Typically used to put the
PHY chip in loopback mode.
TXENA - Transmit enabled when set. Transmit is disabled if clear. When the bit is cleared the
LAN91C111 will complete the current transmission before stopping. When stopping due to an error,
this bit is automatically cleared.
8.6
Bank 0 - EPH Status Register
OFFSET
NAME
TYPE
SYMBOL
2
EPH STATUS REGISTER
READ ONLY
EPHSR
This register stores the status of the last transmitted frame. This register value, upon individual
transmit packet completion, is stored as the first word in the memory area allocated to the packet.
Packet interrupt processing should use the copy in memory as the register itself will be updated by
subsequent packet transmissions. The register can be used for real time values (like TXENA and LINK
OK). If TXENA is cleared the register holds the last packet completion status.
HIGH
BYTE
LOW
BYTE
TX UNRN
LINK_
OK
Reserved
CTR
_ROL
EXC
_DEF
LOST
CARR
LATCOL
Reserved
0
-nLNK pin
0
0
0
0
0
0
TX
DEFR
LTX
BRD
SQET
16COL
LTX
MULT
MUL
COL
SNGL
COL
TX_SUC
0
0
0
0
0
0
0
0
TXUNRN - Transmit Under Run. Set if under run occurs, it also clears TXENA bit in TCR. Cleared by
setting TXENA high. This bit may only be set if early TX is being used.
LINK_OK - General purpose input port driven by nLNK pin inverted. Typically used for Link Test. A
transition on the value of this bit generates an interrupt.
CTR_ROL - Counter Roll Over. When set one or more 4 bit counters have reached maximum count
(15). Cleared by reading the ECR register.
EXC_DEF - Excessive Deferral. When set last/current transmit was deferred for more than 1518 * 2
byte times. Cleared at the end of every packet sent.
LOST_CARR - Lost Carrier Sense. When set indicates that Carrier Sense was not present at end of
preamble. Valid only if MON_CSN is enabled. This condition causes TXENA bit in TCR to be reset.
Cleared by setting TXENA bit in TCR.
LATCOL - Late collision detected on last transmit frame. If set a late collision was detected (later than
64 byte times into the frame). When detected the transmitter jams and turns itself off clearing the
TXENA bit in TCR. Cleared by setting TXENA in TCR.
TX_DEFR - Transmit Deferred. When set, carrier was detected during the first 6.4 µs of the inter frame
gap. Cleared at the end of every packet sent.
LTX_BRD - Last transmit frame was a broadcast. Set if frame was broadcast. Cleared at the start of
every transmit frame.
SQET - Signal Quality Error Test. This bit is set under the following conditions:
Revision 1.8 (07-13-05)
58
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
1. LAN91C111 is set to operate in Half Duplex mode (SWFDUP=0);
2. When STP_SQET=1 and SWFDUP=0, SQET bit will be set upon completion of a transmit
operation and no SQET Pulse has occurred during the IPG (Inter Frame Gap). If a pulse has
occurred during the IPG, SQET bit will not get set.
3. Once SQET bit is set, setting the TXENA bit in TCR register, or via hardware /software reset can
clear this bit.
16COL - 16 collisions reached. Set when 16 collisions are detected for a transmit frame. TXENA bit
in TCR is reset. Cleared when TXENA is set high.
LTX_MULT - Last transmit frame was a multicast. Set if frame was a multicast. Cleared at the start
of every transmit frame.
MULCOL - Multiple collision detected for the last transmit frame. Set when more than one collision
was experienced. Cleared when TX_SUC is high at the end of the packet being sent.
SNGLCOL - Single collision detected for the last transmit frame. Set when a collision is detected.
Cleared when TX_SUC is high at the end of the packet being sent.
TX_SUC - Last transmit was successful. Set if transmit completes without a fatal error. This bit is
cleared by the start of a new frame transmission or when TXENA is set high. Fatal errors are:
8.7
HIGH
BYTE
LOW
BYTE
■
16 collisions (1/2 duplex mode only)
■
SQET fail and STP_SQET = 1 (1/2 duplex mode only)
■
FIFO Underrun
■
Carrier lost and MON_CSN = 1 (1/2 duplex mode only)
■
Late collision (1/2 duplex mode only)
Bank 0 - Receive Control Register
OFFSET
NAME
TYPE
SYMBOL
4
RECEIVE CONTROL
REGISTER
READ/WRITE
RCR
SOFT
RST
FILT
CAR
ABORT_E
NB
Reserved
Reserved
Reserved
STRIP
CRC
RXEN
0
0
0
0
0
0
0
0
Reserved
Reserved
Reserved
Reserved
Reserved
ALMUL
PRMS
RX_
ABORT
0
0
0
0
0
0
0
0
SOFT_RST - Software-Activated Reset. Active high. Initiated by writing this bit high and terminated by
writing the bit low. The LAN91C111’s configuration is not preserved except for Configuration, Base,
and IA0-IA5 Registers. EEPROM is not reloaded after software reset.
FILT_CAR - Filter Carrier. When set filters leading edge of carrier sense for 12 bit times (3 nibble
times). Otherwise recognizes a receive frame as soon as carrier sense is active. (Does NOT filter RX
DV on MII!)
SMSC LAN91C111-REV B
59
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
ABORT_ENB - Enables abort of receive when collision occurs. Defaults low. When set, the
LAN91C111 will automatically abort a packet being received when the appropriate collision input is
activated. This bit has no effect if the SWFDUP bit in the TCR is set.
STRIP_CRC - When set, it strips the CRC on received frames. As a result, both the Byte Count and
the frame format do not contain the CRC. When clear, the CRC is stored in memory following the
packet. Defaults low.
RXEN - Enables the receiver when set. If cleared, completes receiving current frame and then goes
idle. Defaults low on reset.
ALMUL - When set accepts all multicast frames (frames in which the first bit of DA is '1'). When clear
accepts only the multicast frames that match the multicast table setting. Defaults low.
PRMS - Promiscuous mode. When set receives all frames. Does not receive its own transmission
unless it is in Full Duplex!
RX_ABORT - This bit is set if a receive frame was aborted due to length longer than 2K bytes. The
frame will not be received. The bit is cleared by RESET or by the CPU writing it low.
Reserved - Must be 0.
8.8
Bank 0 - Counter Register
OFFSET
NAME
TYPE
SYMBOL
6
COUNTER REGISTER
READ ONLY
ECR
Counts four parameters for MAC statistics. When any counter reaches 15 an interrupt is issued. All
counters are cleared when reading the register and do not wrap around beyond 15.
HIGH
BYTE
NUMBER OF EXC. DEFFERED TX
0
LOW
BYTE
0
0
NUMBER OF DEFFERED TX
0
0
MULTIPLE COLLISION COUNT
0
0
0
0
0
0
SINGLE COLLISION COUNT
0
0
0
0
0
Each four bit counter is incremented every time the corresponding event, as defined in the EPH
STATUS REGISTER bit description, occurs. Note that the counters can only increment once per
enqueued transmit packet, never faster, limiting the rate of interrupts that can be generated by the
counters. For example if a packet is successfully transmitted after one collision the SINGLE
COLLISION COUNT field is incremented by one. If a packet experiences between 2 to 16 collisions,
the MULTIPLE COLLISION COUNT field is incremented by one. If a packet experiences deferral the
NUMBER OF DEFERRED TX field is incremented by one, even if the packet experienced multiple
deferrals during its collision retries.
The COUNTER REGISTER facilitates maintaining statistics in the AUTO RELEASE mode where no
transmit interrupts are generated on successful transmissions.
Reading the register in the transmit service routine will be enough to maintain statistics.
Revision 1.8 (07-13-05)
60
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
8.9
Bank 0 - Memory Information Register
OFFSET
NAME
TYPE
SYMBOL
8
MEMORY INFORMATION
REGISTER
READ ONLY
MIR
HIGH
BYTE
FREE MEMORY AVAILABLE (IN BYTES * 2K * M)
0
0
0
0
0
1
0
0
1
0
0
MEMORY SIZE (IN BYTES *2K * M)
LOW
BYTE
0
0
0
0
0
FREE MEMORY AVAILABLE - This register can be read at any time to determine the amount of free
memory. The register defaults to the MEMORY SIZE upon POR (Power On Reset) or upon the RESET
MMU command.
MEMORY SIZE - This register can be read to determine the total memory size.
All memory related information is represented in 2K * M byte units, where the multiplier M is 1 for
LAN91C111.
8.10
HIGH
BYTE
LOW
BYTE
Bank 0 - Receive/Phy Control Register
OFFSET
NAME
TYPE
SYMBOL
A
RECEIVE/PHY CONTROL
REGISTER
READ/WRITE
RPCR
Reserved
Reserved
SPEED
DPLX
ANEG
Reserved
Reserved
Reserved
0
0
0
0
0
0
0
0
LS2A
LS1A
LS0A
LS2B
LS1B
LS0B
Reserved
Reserved
0
0
0
0
0
0
0
0
SPEED – Speed select Input. This bit is valid and selects 10/100 PHY operation only when the ANEG
Bit = 0, this bit overrides the SPEED bit in the PHY Register 0 (Control Register) and determine the
speed mode. When this bit is set (1), the Internal PHY will operate at 100Mbps. When this bit is
cleared (0), the Internal PHY will operate at 10Mbps. When the ANEG bit = 1, this bit is ignored and
10/100 operation is determined by the outcome of the Auto-negotiation or this bit is overridden by the
SPEED bit in the PHY Register 0 (Control Register) when the ANEG_EN bit in the PHY Register 0
(Control Register) is clear.
DPLX – Duplex Select - This bit selects Full/Half Duplex operation. This bit is valid and selects duplex
operation only when the ANEG Bit = 0, this bit overrides the DPLX bit in the PHY Register 0 (Control
SMSC LAN91C111-REV B
61
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Register) and determine the duplex mode. When this bit is set (1), the Internal PHY will operate at
full duplex mode. When this bit is cleared (0), the Internal PHY will operate at half Duplex mode. When
the ANEG bit = 1, this bit is ignored and duplex mode is determined by the outcome of the Autonegotiation or this bit is overridden by the DPLX bit in the PHY Register 0 (Control Register) when the
ANEG_EN bit in the PHY Register 0 (Control Register) is clear.
ANEG – Auto-Negotiation mode select - The PHY is placed in Auto-Negotiation mode when the ANEG
bit and the ANEG_EN bit in PHY Register 0 (Control Register) both are set. When either of these bits
is cleared (0), the PHY is placed in manual mode.
WHAT DO YOU
WANT TO DO?
Try to Auto-Negotiate
to ……
AUTONEGOTIATION
CONTROL BITS
AUTO-NEGOTIATION ADVERTISEMENT
REGISTER
DUPLEX
MODE
CONTROL
FOR THE
MAC
ANEG
Bit
ANEG_E
N
Bit
TX_FDX
Bit
TX_HDX
Bit
10_FDX
Bit
10_HDX
Bit
SWFDUP
Bit
RPCR
(MAC
)
Register 0
(PHY)
Register
4
(PHY)
Register
4
(PHY)
Register
4
(PHY)
Register
4
(PHY)
Transmit
Control
Register
(MAC)
100 Full Duplex
1
1
1
1
1
1
1
100 Half Duplex
1
1
0
1
1
1
0
10 Full Duplex
1
1
0
0
1
1
1
10 Half Duplex
1
1
0
0
0
1
0
WHAT DO YOU
WANT TO DO?
Try to Manually Set to
……
100 Full Duplex
100 Half Duplex
Revision 1.8 (07-13-05)
AUTONEGOTIATION
CONTROL BITS
SPEED AND DUPLEX MODE CONTROL
FOR THE PHY
DUPLEX
MODE
CONTROL
FOR THE
MAC
ANEG
Bit
ANEG_E
N
Bit
SPEED
Bit
DPLX
Bit
SPEED
Bit
DPLX
Bit
SWFDUP
Bit
RPCR
(MAC
Bank
0
Offset
A)
Register 0
(PHY)
RPCR
(MAC
Bank 0
Offset A)
RPCR
(MAC
Bank 0
Offset A)
Register
0
(PHY)
Register
0
(PHY)
Transmit
Control
Register
(MAC)
0
0
1
1
X
X
1
0
1
1
1
X
X
1
1
0
X
X
1
1
1
0
0
1
0
X
X
0
0
1
1
0
X
X
0
1
0
X
X
1
0
0
62
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
WHAT DO YOU
WANT TO DO?
10 Full Duplex
10 Half Duplex
AUTONEGOTIATION
CONTROL BITS
SPEED AND DUPLEX MODE CONTROL
FOR THE PHY
DUPLEX
MODE
CONTROL
FOR THE
MAC
0
0
0
1
X
X
1
0
1
0
1
X
X
1
1
0
X
X
0
1
1
0
0
0
0
X
X
0
0
1
0
0
X
X
0
1
0
X
X
0
0
0
LS2A, LS1A, LS0A – LED select Signal Enable. These bits define what LED control signals are routed
to the LEDA output pin on the LAN91C111 Ethernet Controller. The default is 10/100 Link detected.
LS2A
LS1A
LS0A
LED SELECT SIGNAL – LEDA
0
0
0
nPLED3+ nPLED0 – Logical OR of 100Mbps Link detected 10Mbps Link detected
(default)
0
0
1
Reserved
0
1
0
nPLED0 - 10Mbps Link detected
0
1
1
nPLED1 - Full Duplex Mode enabled
1
0
0
nPLED2 - Transmit or Receive packet occurred
1
0
1
nPLED3 - 100Mbps Link detected
1
1
0
nPLED4 - Receive packet occurred
1
1
1
nPLED5 - Transmit packet occurred
LS2B, LS1B, LS0B – LED select Signal Enable. These bits define what LED control signals are routed
to the LEDB output pin on the LAN91C111 Ethernet Controller. The default is 10/100 Link detected.
LS2B
LS1B
LS0B
LED SELECT SIGNAL – LEDB
0
0
0
nPLED3+ nPLED0 – Logical OR of 100Mbps Link detected 10Mbps Link detected
(default)
0
0
1
Reserved
0
1
0
nPLED0 - 10Mbps Link detected
0
1
1
nPLED1 – Full Duplex Mode enabled
1
0
0
nPLED2 – Transmit or Receive packet occurred
1
0
1
nPLED3 - 100Mbps Link detected
1
1
0
nPLED4 - Receive packet occurred
1
1
1
nPLED5 - Transmit packet occurred
SMSC LAN91C111-REV B
63
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Reserved – Must be 0.
8.11
Bank 1 - Configuration Register
OFFSET
NAME
TYPE
SYMBOL
0
CONFIGURATION
REGISTER
READ/WRITE
CR
The Configuration Register holds bits that define the adapter configuration and are not expected to
change during run-time. This register is part of the EEPROM saved setup.
HIGH
BYTE
LOW
BYTE
EPH
Power
EN
Reserved
Reserved
NO
WAIT
Reserved
GPCNTRL
EXT PHY
Reserved
1
0
1
0
0
0
0
0
Reserved
Reserved
Reserved
Reserved
Reserved
1
0
0
0
1
Reserved
1
1
0
EPH Power EN - Used to selectively power transition the EPH to a low power mode. When this bit is
cleared (0), the Host will place the EPH into a low power mode. The Ethernet MAC will gate the 25Mhz
TX and RX clock so that the Ethernet MAC will no longer be able to receive and transmit packets. The
Host interface however, will still be active allowing the Host access to the device through Standard IO
access. All LAN91C111 registers will still be accessible. However, status and control will not be allowed
until the EPH Power EN bit is set AND a RESET MMU command is initiated.
NO WAIT - When set, does not request additional wait states. An exception to this are accesses to
the Data Register if not ready for a transfer. When clear, negates ARDY for two to three clocks on
any cycle to the LAN91C111.
GPCNTRL - This bit is a general purpose output port. Its inverse value drives pin nCNTRL and it is
typically connected to a SELECT pin of the external PHY device such as a power enable. It can be
used to select the signaling mode for the external PHY or as a general purpose non-volatile
configuration pin. Defaults low.
EXT PHY – External PHY Enabled.
This bit, when set (1):
a. Enables the external MII.
b. The Internal PHY is disabled and is disconnected (Tri-stated from the internal MII along with any
sideband signals (such as MDINT) going to the MAC Core).
When this bit is cleared (0 - Default):
a. The internal PHY is enabled.
b. The external MII pins, including the MII Management interface pins are tri-stated.
Reserved – Reserved bits.
Revision 1.8 (07-13-05)
64
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
8.12
Bank 1 - Base Address Register
OFFSET
NAME
TYPE
SYMBOL
2
BASE ADDRESS
REGISTER
READ/WRITE
BAR
This register holds the I/O address decode option chosen for the LAN91C111. It is part of the EEPROM
saved setup and is not usually modified during run-time.
HIGH
BYTE
A15
A14
A13
A9
A8
A7
A6
A5
0
0
0
1
1
0
0
0
LOW
BYTE
Reserved
0
0
0
Reserved
0
0
0
0
1
A15 - A13 and A9 - A5 - These bits are compared against the I/O address on the bus to determine
the IOBASE for the LAN91C111‘s registers. The 64k I/O space is fully decoded by the LAN91C111
down to a 16 location space, therefore the unspecified address lines A4, A10, A11 and A12 must be
all zeros.
All bits in this register are loaded from the serial EEPROM. The I/O base decode defaults to 300h
(namely, the high byte defaults to 18h).
Reserved – Reserved bits.
Below chart shows the decoding of I/O Base Address 300h:
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
0
8.13
Bank 1 - Individual Address Registers
OFFSET
NAME
TYPE
SYMBOL
4
THROUG
H9
INDIVIDUAL ADDRESS
REGISTERS
READ/WRITE
IAR
These registers are loaded starting at word location 20h of the EEPROM upon hardware reset or
EEPROM reload. The registers can be modified by the software driver, but a STORE operation will not
modify the EEPROM Individual Address contents. Bit 0 of Individual Address 0 register corresponds
to the first bit of the address on the cable.
SMSC LAN91C111-REV B
65
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
LOW
BYTE
ADDRESS 0
0
0
0
0
HIGH
BYTE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ADDRESS 1
0
0
0
0
LOW
BYTE
0
ADDRESS 2
0
0
0
0
0
ADDRESS 3
HIGH
BYTE
0
0
0
0
0
ADDRESS 4
LOW
BYTE
0
0
0
0
HIGH
BYTE
0
ADDRESS 5
0
8.14
0
0
0
0
0
Bank 1 - General Purpose Register
OFFSET
NAME
TYPE
SYMBOL
A
GENERAL PURPOSE
REGISTER
READ/WRITE
GPR
HIGH
BYTE
HIGH DATA BYTE
0
0
0
LOW
BYTE
0
0
LOW DATA BYTE
0
0
0
0
0
This register can be used as a way of storing and retrieving non-volatile information in the EEPROM
to be used by the software driver. The storage is word oriented, and the EEPROM word address to
be read or written is specified using the six lowest bits of the Pointer Register.
This register can also be used to sequentially program the Individual Address area of the EEPROM,
that is normally protected from accidental Store operations.
This register will be used for EEPROM read and write only when the EEPROM SELECT bit in the
Control Register is set. This allows generic EEPROM read and write routines that do not affect the
basic setup of the LAN91C111.
Revision 1.8 (07-13-05)
66
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
8.15
HIGH
BYTE
LOW BYTE
Bank 1 - Control Register
OFFSET
NAME
TYPE
SYMBOL
C
CONTROL REGISTER
READ/WRITE
CTR
Reserved
RCV_
BAD
Reserved
Reserved
AUTO
RELEASE
Reserved
Reserved
Reserved
0
0
0
1
0
0
1
0
LE
ENABLE
CR
ENABLE
TE
ENABLE
Reserved
Reserved
EEPROM
SELECT
RELOAD
STORE
0
0
0
1
0
0
0
0
RCV_BAD - When set, bad CRC packets are received. When clear bad CRC packets do not generate
interrupts and their memory is released.
AUTO RELEASE - When set, transmit pages are released by transmit completion if the transmission
was successful (when TX_SUC is set). In that case there is no status word associated with its packet
number, and successful packet numbers are not even written into the TX COMPLETION FIFO. A
sequence of transmit packets will generate an interrupt only when the sequence is completely
transmitted (TX EMPTY INT will be set), or when a packet in the sequence experiences a fatal error
(TX INT will be set). Upon a fatal error TXENA is cleared and the transmission sequence stops. The
packet number that failed, is present in the FIFO PORTS register, and its pages are not released,
allowing the CPU to restart the sequence after corrective action is taken.
LE ENABLE - Link Error Enable. When set it enables the LINK_OK bit transition as one of the
interrupts merged into the EPH INT bit. Clearing the LE ENABLE bit after an EPH INT interrupt, caused
by a LINK_OK transition, will acknowledge the interrupt. LE ENABLE defaults low (disabled).
CR ENABLE - Counter Roll over Enable. When set, it enables the CTR_ROL bit as one of the
interrupts merged into the EPH INT bit. Reading the COUNTER register after an EPH INT interrupt
caused by a counter rollover, will acknowledge the interrupt. CR ENABLE defaults low (disabled).
TE ENABLE - Transmit Error Enable. When set it enables Transmit Error as one of the interrupts
merged into the EPH INT bit. An EPH INT interrupt caused by a transmitter error is acknowledged by
setting TXENA bit in the TCR register to 1 or by clearing the TE ENABLE bit. TE ENABLE defaults
low (disabled). Transmit Error is any condition that clears TXENA with TX_SUC staying low as
described in the EPHSR register.
EEPROM SELECT - This bit allows the CPU to specify which registers the EEPROM RELOAD or
STORE refers to. When high, the General Purpose Register is the only register read or written. When
low, RELOAD reads Configuration, Base and Individual Address, and STORE writes the Configuration
and Base registers.
RELOAD - When set it will read the EEPROM and update relevant registers with its contents. Clears
upon completing the operation.
STORE - When set, stores the contents of all relevant registers in the serial EEPROM. Clears upon
completing the operation.
Note: When an EEPROM access is in progress the STORE and RELOAD bits will be read back as
high. The remaining 14 bits of this register will be invalid. During this time attempted read/write
operations, other than polling the EEPROM status, will NOT have any effect on the internal
registers. The CPU can resume accesses to the LAN91C111 after both bits are low. A worst
case RELOAD operation initiated by RESET or by software takes less than 750 µs.
SMSC LAN91C111-REV B
67
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
8.16
Bank 2 - MMU Command Register
OFFSET
NAME
TYPE
SYMBOL
0
MMU COMMAND
REGISTER
WRITE ONLY
BUSY BIT
READABLE
MMUCR
This register is used by the CPU to control the memory allocation, de-allocation, TX FIFO and RX
FIFO control.
The three command bits determine the command issued as described below:
HIGH
BYTE
LOW
BYTE
COMMAND
Reserved
Reserved
Reserved
Reserved
BUSY
Operation Code
0
COMMAND SET:
OPERATION
CODE
DECIMAL
VALUE
COMMAND
000
0
NOOP - NO OPERATION
001
1
ALLOCATE MEMORY FOR TX
010
2
RESET MMU TO INITIAL STATE - Frees all memory allocations, clears relevant
interrupts, resets packet FIFO pointers.
011
3
REMOVE FRAME FROM TOP OF RX FIFO - To be issued after CPU has
completed processing of present receive frame. This command removes the
receive packet number from the RX FIFO and brings the next receive frame (if
any) to the RX area (output of RX FIFO).
100
4
REMOVE AND RELEASE TOP OF RX FIFO - Like 3) but also releases all
memory used by the packet presently at the RX FIFO output. The MMU busy
time after issuing REMOVE and RELEASE command depends on the time when
the busy bit is cleared. The time from issuing REMOVE and RELEASE command
on the last receive packet to the time when receive FIFO is empty depends on
RX INT bit turning low. An alternate approach can be checking the read RX FIFO
register.
101
5
RELEASE SPECIFIC PACKET - Frees all pages allocated to the packet specified
in the PACKET NUMBER REGISTER. Should not be used for frames pending
transmission. Typically used to remove transmitted frames, after reading their
completion status. Can be used following 3) to release receive packet memory
in a more flexible way than 4).
110
6
ENQUEUE PACKET NUMBER INTO TX FIFO - This is the normal method of
transmitting a packet just loaded into RAM. The packet number to be enqueued
is taken from the PACKET NUMBER REGISTER.
Revision 1.8 (07-13-05)
68
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
OPERATION
CODE
DECIMAL
VALUE
111
7
COMMAND
RESET TX FIFOs - This command will reset both TX FIFOs: The TX FIFO
holding the packet numbers awaiting transmission and the TX Completion FIFO.
This command provides a mechanism for canceling packet transmissions, and
reordering or bypassing the transmit queue. The RESET TX FIFOs command
should only be used when the transmitter is disabled. Unlike the RESET MMU
command, the RESET TX FIFOs does not release any memory.
Note:
■
When using the RESET TX FIFOS command, the CPU is responsible for releasing the memory
associated with outstanding packets, or re-enqueuing them. Packet numbers in the completion
FIFO can be read via the FIFO ports register before issuing the command.
■
MMU commands releasing memory (commands 4 and 5) should only be issued if the
corresponding packet number has memory allocated to it.
COMMAND SEQUENCING
A second allocate command (command 1) should not be issued until the present one has completed.
Completion is determined by reading the FAILED bit of the allocation result register or through the
allocation interrupt.
A second release command (commands 4, 5) should not be issued if the previous one is still being
processed. The BUSY bit indicates that a release command is in progress. After issuing command 5,
the contents of the PNR should not be changed until BUSY goes low. After issuing command 4,
command 3 should not be issued until BUSY goes low.
BUSY BIT - Readable at bit 0 of the MMU command register address. When set indicates that MMU
is still processing a release command. When clear, MMU has already completed last release
command. BUSY and FAILED bits are set upon the trailing edge of command.
8.17
Bank 2 - Packet Number Register
OFFSET
NAME
TYPE
SYMBOL
2
PACKET NUMBER
REGISTER
READ/WRITE
PNR
Reserved
Reserved
0
0
PACKET NUMBER AT TX AREA
0
0
0
0
0
0
PACKET NUMBER AT TX AREA - The value written into this register determines which packet number
is accessible through the TX area. Some MMU commands use the number stored in this register as
the packet number parameter. This register is cleared by a RESET or a RESET MMU Command.
OFFSET
NAME
TYPE
SYMBOL
3
ALLOCATION RESULT
REGISTER
READ ONLY
ARR
This register is updated upon an ALLOCATE MEMORY MMU command.
SMSC LAN91C111-REV B
69
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
FAILED
Reserved
1
0
ALLOCATED PACKET NUMBER
0
0
0
0
0
0
FAILED - A zero indicates a successful allocation completion. If the allocation fails the bit is set and
only cleared when the pending allocation is satisfied. Defaults high upon reset and reset MMU
command. For polling purposes, the ALLOC_INT in the Interrupt Status Register should be used
because it is synchronized to the read operation. Sequence:
1. Allocate Command
2. Poll ALLOC_INT bit until set
3. Read Allocation Result Register
ALLOCATED PACKET NUMBER - Packet number associated with the last memory allocation request.
The value is only valid if the FAILED bit is clear.
Note: For software compatibility with future versions, the value read from the ARR after an allocation
request is intended to be written into the PNR as is, without masking higher bits (provided
FAILED = 0).
8.18
Bank 2 - FIFO Ports Register
OFFSET
NAME
TYPE
SYMBOL
4
FIFO PORTS REGISTER
READ ONLY
FIFO
This register provides access to the read ports of the Receive FIFO and the Transmit completion FIFO.
The packet numbers to be processed by the interrupt service routines are read from this register.
HIGH
BYTE
LOW
BYTE
REMPTY
Reserved
1
0
TEMPTY
Reserved
1
0
RX FIFO PACKET NUMBER
0
0
0
0
0
0
0
0
TX FIFO PACKET NUMBER
0
0
0
0
REMPTY - No receive packets queued in the RX FIFO. For polling purposes, uses the RCV_INT bit
in the Interrupt Status Register.
TOP OF RX FIFO PACKET NUMBER - Packet number presently at the output of the RX FIFO. Only
valid if REMPTY is clear. The packet is removed from the RX FIFO using MMU Commands 3) or 4).
TEMPTY - No transmit packets in completion queue. For polling purposes, uses the TX_INT bit in the
Interrupt Status Register.
TX FIFO PACKET NUMBER - Packet number presently at the output of the TX FIFO. Only valid if
TEMPTY is clear. The packet is removed when a TX INT acknowledge is issued.
Note: For software compatibility with future versions, the value read from each FIFO register is
intended to be written into the PNR as is, without masking higher bits (provided TEMPTY and
REMPTY = 0 respectively).
Revision 1.8 (07-13-05)
70
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
8.19
Bank 2 - Pointer Register
OFFSET
6
HIGH
BYTE
NAME
TYPE
SYMBOL
POINTER REGISTER
READ/WRITE
NOT EMPTY IS
A READ ONLY
BIT
PTR
RCV
AUTO
INCR.
READ
ETEN
NOT
EMPTY
0
0
0
0
0
LOW
BYTE
POINTER HIGH
0
0
0
0
0
0
POINTER LOW
0
0
0
0
0
POINTER REGISTER - The value of this register determines the address to be accessed within the
transmit or receive areas. It will auto-increment on accesses to the data register when AUTO INCR.
is set. The increment is by one for every byte access, by two for every word access, and by four for
every double word access. When RCV is set the address refers to the receive area and uses the
output of RX FIFO as the packet number, when RCV is clear the address refers to the transmit area
and uses the packet number at the Packet Number Register.
READ - Determines the type of access to follow. If the READ bit is high the operation intended is a
read. If the READ bit is low the operation is a write. Loading a new pointer value, with the READ bit
high, generates a pre-fetch into the Data Register for read purposes.
Readback of the pointer will indicate the value of the address last accessed by the CPU (rather than
the last pre-fetched). This allows any interrupt routine that uses the pointer, to save it and restore it
without affecting the process being interrupted. The Pointer Register should not be loaded until the
Data Register FIFO is empty. The NOT EMPTY bit of this register can be read to determine if the
FIFO is empty. On reads, if ARDY is not connected to the host, the Data Register should not be read
before 370ns after the pointer was loaded to allow the Data Register FIFO to fill.
If the pointer is loaded using 8 bit writes, the low byte should be loaded first and the high byte last.
ETEN - When set enables EARLY Transmit underrun detection. Normal operation when clear.
NOT EMPTY - When set indicates that the Write Data FIFO is not empty yet. The CPU can verify that
the FIFO is empty before loading a new pointer value. This is a read only bit.
Note: If AUTO INCR. is not set, the pointer must be loaded with a dword aligned value.
8.20
Bank 2 - Data Register
OFFSET
NAME
TYPE
SYMBOL
8 THROUGH
BH
DATA REGISTER
READ/WRITE
DATA
SMSC LAN91C111-REV B
71
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
DATA HIGH
X
X
X
X
X
X
X
X
X
X
X
X
DATA LOW
X
X
X
X
DATA REGISTER - Used to read or write the data buffer byte/word presently addressed by the pointer
register.
This register is mapped into two uni-directional FIFOs that allow moving words to and from the
LAN91C111 regardless of whether the pointer address is even, odd or dword aligned. Data goes
through the write FIFO into memory, and is pre-fetched from memory into the read FIFO. If byte
accesses are used, the appropriate (next) byte can be accessed through the Data Low or Data High
registers. The order to and from the FIFO is preserved. Byte, word and dword accesses can be mixed
on the fly in any order.
This register is mapped into two consecutive word locations to facilitate double word move operations
regardless of the actual bus width (16 or 32 bits). The DATA register is accessible at any address in
the 8 through Bh range, while the number of bytes being transferred is determined by A1 and nBE0nBE3. The FIFOs are 12 bytes each.
8.21
Bank 2 - Interrupt Status Registers
OFFSET
NAME
TYPE
SYMBOL
C
INTERRUPT STATUS
REGISTER
READ ONLY
IST
MDINT
ERCV INT
EPH INT
RX_OVRN
INT
ALLOC INT
TX EMPTY
INT
TX INT
RCV INT
0
0
0
0
0
1
0
0
OFFSET
C
MDINT
ERCV INT
Revision 1.8 (07-13-05)
NAME
TYPE
INTERRUPT
ACKNOWLEDGE REGISTER
SYMBOL
WRITE ONLY
RX_OVRN
INT
TX EMPTY
INT
72
DATASHEET
ACK
TX INT
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
OFFSET
NAME
TYPE
SYMBOL
D
INTERRUPT MASK
REGISTER
READ/WRITE
MSK
MDINT
MASK
ERCV INT
MASK
EPH INT
MASK
RX_OVRN
INT
MASK
ALLOC INT
MASK
TX EMPTY
INT
MASK
TX INT
MASK
RCV INT
MASK
0
0
0
0
0
0
0
0
This register can be read and written as a word or as two individual bytes.
The Interrupt Mask Register bits enable the appropriate bits when high and disable them when low. A
MASK bit being set will cause a hardware interrupt.
MDINT - Set when the following bits in the PHY MI Register 18 (Serial Port Status Output Register)
change state.
1. LNKFAIL, 2) LOSSSYNC, 3) CWRD, 4) SSD, 5) ESD, 6) PROL, 7) JAB, 8) SPDDET, 9) DPLXDET.
These bits automatically latch upon changing state and stay latched until they are read. When they
are read, the bits that caused the interrupt to happen are updated to their current value. The MDINT
bit will be cleared by writing the acknowledge register with MDINT bit set.
ERCV INT - Early receive interrupt. Set whenever a receive packet is being received, and the number
of bytes received into memory exceeds the value programmed as ERCV THRESHOLD (Bank 3, Offset
Ch). ERCV INT stays set until acknowledged by writing the INTERRUPT ACKNOWLEDGE REGISTER
with the ERCV INT bit set.
EPH INT - Set when the Ethernet Protocol Handler section indicates one out of various possible
special conditions. This bit merges exception type of interrupt sources, whose service time is not
critical to the execution speed of the low level drivers. The exact nature of the interrupt can be obtained
from the EPH Status Register (EPHSR), and enabling of these sources can be done via the Control
Register. The possible sources are:
LINK - Link Test transition
CTR_ROL - Statistics counter roll over
TXENA cleared - A fatal transmit error occurred forcing TXENA to be cleared. TX_SUC will be low and
the specific reason will be reflected by the bits:
■
TXUNRN - Transmit under-run
■
SQET - SQE Error
■
LOST CARR - Lost Carrier
■
LATCOL - Late Collision
■
16COL - 16 collisions
Any of the above interrupt sources can be masked by the appropriate ENABLE bits in the Control
Register.
1. 1) LE ENABLE (Link Error Enable), 2) CR ENABLE (Counter Roll Over), 3) TE ENABLE (Transmit
Error Enable)
EPH INT will only be cleared by the following methods:
SMSC LAN91C111-REV B
73
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
■
Clearing the LE ENABLE bit in the Control Register if an EPH interrupt is caused by a LINK_OK
transition.
■
Reading the Counter Register if an EPH interrupt is caused by statistics counter roll over.
■
Setting TXENA bit high if an EPH interrupt is caused by any of the fatal transmit error listed above
(3.1 to 3.5).
RX_OVRN INT - Set when 1) the receiver aborts due to an overrun due to a failed memory allocation,
2) the receiver aborts due to a packet length of greater than 2K bytes, or 3) the receiver aborts due
to the RCV DISCRD bit in the ERCV register set. The RX_OVRN INT bit latches the condition for the
purpose of being polled or generating an interrupt, and will only be cleared by writing the acknowledge
register with the RX_OVRN INT bit set.
ALLOC INT - Set when an MMU request for TX ram pages is successful. This bit is the complement
of the FAILED bit in the ALLOCATION RESULT register. The ALLOC INT bit is cleared by the MMU
when the next allocation request is processed or allocation fails.
TX EMPTY INT - Set if the TX FIFO goes empty, can be used to generate a single interrupt at the
end of a sequence of packets enqueued for transmission. This bit latches the empty condition, and
the bit will stay set until it is specifically cleared by writing the acknowledge register with the TX EMPTY
INT bit set. If a real time reading of the FIFO empty is desired, the bit should be first cleared and then
read.
The TX_EMPTY MASK bit should only be set after the following steps:
■
A packet is enqueued for transmission
■
The previous empty condition is cleared (acknowledged)
TX INT - Set when at least one packet transmission was completed or any of the below transmit fatal
errors occurs:
■
TXUNRN - Transmit under-run
■
SQET - SQE Error
■
LOST CARR - Lost Carrier
■
LATCOL - Late Collision
■
16COL - 16 collisions
The first packet number to be serviced can be read from the FIFO PORTS register. The TX INT bit is
always the logic complement of the TEMPTY bit in the FIFO PORTS register. After servicing a packet
number, its TX INT interrupt is removed by writing the Interrupt Acknowledge Register with the TX INT
bit set.
RCV INT - Set when a receive interrupt is generated. The first packet number to be serviced can be
read from the FIFO PORTS register. The RCV INT bit is always the logic complement of the REMPTY
bit in the FIFO PORTS register.
Receive Interrupt is cleared when RX FIFO is empty.
Revision 1.8 (07-13-05)
74
DATASHEET
SMSC LAN91C111-REV B
MERGED INTO EPH INT
EPHSR INTERRUPTS
TX_SVC
TXENA
TEMASK
CRMASK
CTR-ROL
LEMASK
EDGE DETECTOR
ON LINK ERR
nWRACK
Fatal Transmit
Error
TX Complete
IntAck7
IntAck6
IntAck4
IntAck2
IntAck1
nQ
Q
Q
nQ
nQ
Q
Q
nQ
D
nQ
Q
MDINT
D
ERCV
D
RX_OVRN
ALLOCATION
FAILED
D S
TX
FIFO EMPTY
D S
S
DATASHEET
75
S
SMSC LAN91C111-REV B
S
TXUNRN
SQET
LOST CARR
LATCOL
16COL
nRDIST
OE
7
5
DATA
BUS
6
4
3
2
16
D0-7
REGISTER
STATUS
INTERRUPT
1
0
7 6
5
3
2
1
D8-15
REGISTER
INTERRUPT
MASK
4
RCV FIFO
NOT EMPTY
0
nOE
MAIN INTERRUPTS
MDINT
ERCV INT
EPH INT
RX_OVRN
INT
ALLOC
INT
TX
EMPTY
INT
TX INT
RCV INT
INT
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Figure 8.2 Interrupt Structure
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
8.22
Bank 3 - Multicast Table Registers
OFFSET
NAME
TYPE
SYMBOL
0
THROUG
H7
MULTICAST TABLE
READ/WRITE
MT
LOW
BYTE
MULTICAST TABLE 0
0
0
0
HIGH
BYTE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
MULTICAST TABLE 1
0
0
0
LOW
BYTE
0
0
MULTICAST TABLE 2
0
0
0
HIGH
BYTE
0
0
MULTICAST TABLE 3
0
0
0
LOW
BYTE
0
0
MULTICAST TABLE 4
0
0
0
HIGH
BYTE
0
0
MULTICAST TABLE 5
0
0
0
LOW
BYTE
0
0
MULTICAST TABLE 6
0
0
0
HIGH
BYTE
0
0
MULTICAST TABLE 7
0
0
0
0
0
The 64 bit multicast table is used for group address filtering. The hash value is defined as the six most
significant bits of the CRC of the destination addresses. The three msb's determine the register to be
used (MT0-MT7), while the other three determine the bit within the register.
If the appropriate bit in the table is set, the packet is received.
If the ALMUL bit in the RCR register is set, all multicast addresses are received regardless of the
multicast table values.
Hashing is only a partial group addressing filtering scheme, but being the hash value available as part
of the receive status word, the receive routine can reduce the search time significantly. With the proper
memory structure, the search is limited to comparing only the multicast addresses that have the actual
hash value in question.
Revision 1.8 (07-13-05)
76
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
8.23
HIGH
BYTE
Bank 3 - Management Interface
OFFSET
NAME
TYPE
SYMBOL
8
MANAGEMENT
INTERFACE
READ/WRITE
MGMT
Reserved
MSK_
CRS100
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
0
0
1
1
0
0
1
1
MDOE
MCLK
MDI
MDO
0
0
MDI Pin
0
LOW
BYTE
Reserved
0
0
1
1
MSK_CRS100 - Disables CRS100 detection during transmit in half duplex mode (SWFDUP=0).
MDO - MII Management output. The value of this bit drives the MDO pin.
MDI - MII Management input. The value of the MDI pin is readable using this bit.
MDCLK - MII Management clock. The value of this bit drives the MDCLK pin.
MDOE - MII Management output enable. When high pin MDO is driven, when low pin MDO is tristated.
The purpose of this interface, along with the corresponding pins is to implement MII PHY management
in software.
8.24
Bank 3 - Revision Register
OFFSET
NAME
TYPE
SYMBOL
A
REVISION REGISTER
READ ONLY
REV
HIGH
BYTE
0
0
LOW
BYTE
1
1
0
0
CHIP
1
0
1
1
0
1
REV
0
1
0
0
CHIP - Chip ID. Can be used by software drivers to identify the device used.
REV - Revision ID. Incremented for each revision of a given device.
SMSC LAN91C111-REV B
77
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
8.25
Bank 3 - Early RCV Register
OFFSET
NAME
TYPE
SYMBOL
C
EARLY RCV REGISTER
READ/WRITE
ERCV
HIGH
BYTE
LOW
BYTE
Reserved
0
0
0
0
RCV
DISCRD
Reserved
Reserved
0
0
0
0
0
0
0
1
1
ERCV THRESHOLD
1
1
1
RCV DISCRD - Set to discard a packet being received. Will discard packets only in the process of
being received. When set prior to the end of receive packet, bit 4 (RXOVRN) of the interrupt status
register will be set to indicate that the packet was discarded. Otherwise, the packet will be received
normally and bit 0 set (RCVINT) in the interrupt status register. RCV DISCRD is self clearing.
ERCV THRESHOLD - Threshold for ERCV interrupt. Specified in 64 byte multiples. Whenever the
number of bytes written in memory for the presently received packet exceeds the ERCV THRESHOLD,
ERCV INT bit of the INTERRUPT STATUS REGISTER is set.
8.26
Bank 7 - External Registers
OFFSET
NAME
TYPE
0
THROUG
H7
EXTERNAL REGISTERS
SYMBOL
nCSOUT is driven low by the LAN91C111 when a valid access to the EXTERNAL REGISTER range
occurs.
HIGH
BYTE
EXTERNAL R/W REGISTER
LOW
BYTE
EXTERNAL R/W REGISTER
Revision 1.8 (07-13-05)
78
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
CYCLE
NCSOUT
LAN91C111 DATA BUS
AEN=0
A3=0
A4-15 matches I/O BASE
BANK SELECT = 7
Driven low. Transparently latched on nADS
rising edge.
Ignored on writes.
Tri-stated on reads.
BANK SELECT = 4,5,6
High
Ignore cycle.
Otherwise
High
Normal LAN91C111 cycle.
SMSC LAN91C111-REV B
79
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Revision 1.8 (07-13-05)
80
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Chapter 9 PHY MII Registers
Multiple Register Access
Multiple registers can be accessed on a single PHY Ml serial port access cycle with the multiple
register access features. The multiple register access features can be enabled by setting the multiple
register access enables bit in the PHY Ml serial port Configuration 2 register. When multiple register
access is enabled, multiple registers can be accessed on a single PHY Ml serial port access cycle by
setting the register address to 11111 during the first 16 MDC clock cycles. There is no actual register
residing in register address location 11111, so when the register address is then set to 11111, all eleven
registers are accessed on the 176 rising edges of MDC that occur after the first 16 MDC clock cycles
of the PHY Ml serial port access cycle. The registers are accessed in numerical order from 0 to 20.
After all 192 MDC clocks have been completed, all the registers have been read/written, and the serial
shift process is halted, data is latched into the device, and MDIO goes into high impedance state.
Another serial shift cycle cannot be initiated until the idle condition (at least 32 continuous 1's) is
detected.
Bit Types
Since the serial port is bi-directional, there are many types of bits. Write bits (W) are inputs during a
write cycle and are high impedance during a read cycle. Read bits (R) are outputs during a read cycle
and high impedance during a write cycle. Read/Write bits (RW) are actually write bits, which can be
read out during a read cycle. R/WSC bits are R/W bits that are self-clearing after a set period of time
or after a specific event has completed. R/LL bits are read bits that latch themselves when they go
low, and they stay latched low until read. After they are read, they are reset high. R/LH bits are the
same as R/LL bits except that they latch high. R/LT are read bits that latch themselves whenever they
make a transition or change value, and they stay latched until they are read. After R/LT bits are read,
they are updated to their current value. R/LT bits can also be programmed to assert the interrupt
function.
Bit Type Definition
R:
Read Only
R/WSC
:
Read/Write
Self Clearing
W:
Write Only
R/LH:
Read/Latch
high
RW:
Read/Write
R/LL:
Read/Latch
low
R/LT:
Read/Latch on Transition
REGISTER ADDRESS
REGISTER NAME
0
Control
1
Status
2,3
PHY ID
4
Auto-Negotiation Advertisement
5
Auto-Negotiation Remote End Capability
6....15
Reserved
16
Configuration 1
SMSC LAN91C111-REV B
81
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
REGISTER ADDRESS
REGISTER NAME
17
Configuration 2
18
Status Output
19
Mask
20
Reserved
PHY Register Description
Table 9.1 MII Serial Frame Structure
<Idle>
<Start>
<Read>
<Write>
<PHY Addr.>
<REG.Addr.>
<Turnaround>
<Data>
IDLE
ST[1:0]
READ
WRITE
PHYAD[4:0]
REGAD[4:0]
TA[1:0]
D[15:0]
D[15:0]
↓
Register 0
Control
Register 1
Status
Register 2
PHY ID#1
Register 3
PHY ID#2
Register 4
AutoNegotiation Advertisement
Register 5
AutoNegotiation Remote End Capability
Register 16
Configuration 1
Register 17
Configuration 2
Register 18
Status Output
Register 19
Mask
Register 20
Reserved
SYMBOL
NAME
DEFINITION
R/W
IDLE
Idle Pattern
These bits are an idle pattern. Device will not initiate an MI cycle until
it detects at least 32 1's
W
ST1
ST0
Start Bits
When ST[1:0]=01, a MI Serial Port access cycle starts.
W
READ
Read Select
1 = Read Cycle
W
WRITE
Write Select
1 = Write Cycle
W
PHYAD[4:0]
Physical
Device
Address
PHYSICAL ADDRESS
R
Revision 1.8 (07-13-05)
82
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
SYMBOL
NAME
DEFINITION
R/W
REGAD[4:0]
Register
Address
If REGAD[4:0] = 00000-11110, these bits determine the specific
register from which D[15:0] is read/written. If multiple register access
is enabled and REGAD[4:0] = 11111, all registers are read/written in
a single cycle.
W
TA1
TA0
Turnaround
Time
These bits provide some turnaround time for MDIO
R/W
When READ = 1, TA[1:0] = Z0
When WRITE = 1, TA[1:0] = 10
The turnaround time is a 2 bit time spacing between the Register
Address field and the Data field of a management frame to avoid
contention during a read transaction. For a read transaction, both the
STA and the PHY shall remain in a high impedance state for the first
bit time of the turnaround. The PHY shall drive a zero bit during the
second bit time of the turnaround of a read transaction. During a
write transaction, the STA shall drive a one bit for the first bit time of
the turnaround and a zero bit for the second bit time of the
turnaround.
D[15:0]....
Data
SMSC LAN91C111-REV B
These 16 bits contain data to/from one of the eleven registers
selected by register address bits REGAD[4:0].
83
DATASHEET
Any
Revision 1.8 (07-13-05)
Revision 1.8 (07-13-05)
DATASHEET
84
AutoNegot.
Remote
Capability
Reserved
Mask
19
20
Status
Output
18
17 Configuration 2
16 Configuration 1
5
4
AutoNegot.
Advertisement
PHY ID #2
PHY ID #1
2
3
Status
Control
1
0
1
0
0
0
MLNKFAIL
0
MINT
R/W
0
R/W
0
0
Reserved
R/W
Reserved
1
1
1
Reserved
R/W
R/W
R/W
MLOSSSYN
R/LT
R/LT
R
LOSSSYNC
1
R/W
Reserved
0
R/W
LNKFAIL
1
R/W
Reserved
0
R/W
XMTPDN
0
R
RF
0
R/W
RF
1
R
OUI21
0
R
OUI5
1
R
CAP_TXH
1
R/W
SPEED
x.13
INT
1
R/W
Reserved
0
R/W
XMTDIS
R
R
0
LNKDIS
ACK
0
0
NP
R
R/W
1
ACK
R
R
1
NP
OUI20
0
OUI19
R
R
0
OUI4
R
R
0
OUI3
CAP_TXF
0
R/W
LPBK
x.14
CAP_T4
0
R/WSC
RST
x.15
0
R/W
Reserved
1
R/W
MCWRD
0
R/LT
CWRD
1
R/W
Reserved
0
R/W
Reserved
0
R
Reserved
0
R/W
Reserved
1
R
OUI22
0
R
OUI6
1
R
CAP_TF
1
R/W
ANEG_EN
x.12
0
R/W
Reserved
1
R/W
MSSD
0
R/LT
SSD
1
R/W
Reserved
0
R/W
Reserved
0
R
Reserved
0
R/W
Reserved
1
R
OUI23
0
R
OUI7
1
R
CAP_TH
0
R/W
PDN
x.11
0
R/W
Reserved
1
R/W
MESD
0
R/LT
ESD
1
R/W
Reserved
0
R/W
BYPSCR
0
R
Reserved
0
R/W
Reserved
0
R
OUI24
0
R
OUI8
0
0
R/W
Reserved
1
R/W
MRPOL
0
R/LT
RPOL
1
R/W
Reserved
0
R/W
UNSCDS
0
R
T4
0
R/W
T4
0
R
PART5
0
R
OUI9
0
R
Reserved
Reserved
R
0
R/WSC
ANEG_RST
x.9
1 or 0
R/W
MII_DIS
x.10
0
R/W
Reserved
1
1
R/W
Reserved
1
R/W
MSPDDT
MJAB
R/W
1
R/LT
SPDDET
0
R/W
Reserved
0
R/W
CABLE
0
R
TX_HDX
1
R/W
TX_HDX
0
R
PART3
0
R
OUI11
0
R
Reserved
0
R/W
COLTST
x.7
0
R/LT
JAB
1
R/W
Reserved
0
R/W
EQLZR
0
R
TX_FDX
1
R/W
TX_FDX
0
R
PART4
0
R
OUI10
0
R
Reserved
0
R/W
DPLX
x.8
0
R/W
Reserved
1
R/W
MDPLDT
0
R/LT
DPLXDET
0
R/W
Reserved
0
R/W
RLVL0
0
R
10_FDX
1
R/W
10_FDX
1
R
PART2
0
R
OUI12
0
R
CAP_SUPR
0
R/W
Reserved
x.6
1
R/W
Reserved
0
0
R/W
Reserved
0
R/W
Reserved
Reserved
R/W
0
R/LT
Reserved
0
0
R/LT
Reserved
0
R/W
JABDIS
APOLDIS
R/W
0
R/W
TLVL2
0
R
Reserved
0
R/W
Reserved
0
R
PART0
1
R
OUI14
0
R/LH
REM_FLT
0
R/W
Reserved
x.4
1
R/W
TLVL3
0
R
10_HDX
1
R/W
10_HDX
0
R
PART1
0
R
OUI13
0
R
ANEG_ACK
0
R/W
Reserved
x.5
0
R/W
Reserved
0
R/W
Reserved
0
R
Reserved
0
R/W
MREG
0
R/W
TLVL1
0
R
Reserved
0
R/W
Reserved
0
R
REV3
0
R
OUI15
1
R
CAP_ANEG
0
R/W
Reserved
x.3
Reserved
R/W
0
R/W
0
0
R/W
Reserved
0
R
0
R/W
Reserved
0
R/W
Reserved
0
R
Reserved
0
Reserved
R/W
0
Reserved
0
R/W
TRF0
0
R
CSMA
1
R/W
CSMA
0
R
REV0
0
R
OUI18
1
R
EXREG
0
R/W
Reserved
x.0
R/W
Reserved
1
R/W
TRF1
0
R
Reserved
0
R/W
Reserved
0
R
REV1
1
R
OUI17
0
R/LH
JAB
0
R/W
Reserved
x.1
Reserved
0
R/W
Reserved
0
R
Reserved
0
R/W
INTMDIO
0
R/W
TLVL0
0
R
Reserved
0
R/W
Reserved
0
R
REV2
1
R
OUI16
0
R/LL
LINK
0
R/W
Reserved
x.2
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Table 9.2 MII Serial Port Register MAP
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
9.1
Register 0. Control Register
RST
LPBK
SPEED
ANEG_EN
PDN
MII_DIS
ANEG_RST
DPLX
RW, SC
RW
RW
RW
RW
RW
RW. SC
RW
0
0
1
1
0
1
0
0
COLST
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
RST - Reset
A ‘1’ written to this bit will initiate a reset of the PHY. The bit is self-clearing, and the PHY will return
a ‘1’ on reads to this bit until the reset is completed. Write transactions to this register may be ignored
while the PHY is processing the reset. All PHY registers will be driven to their default states after a
reset. The internal PHY is guaranteed to be ready for normal operation 50 mS after the RST bit is
set. Software driver requires to wait for 50mS after setting the RST bit to high to access the internal
PHY again.
LPBK - Loopback
Writing a ‘1’ will put the PHY into loopback mode.
Speed (Speed Selection)
When Auto Negotiation is disabled this bit can be used to manually select the link speed. Writing a
‘1’ to this bit selects 100 Mbps, a ‘0’ selects 10 Mbps.
When Auto-Negotiation is enabled reading or writing this bit has no meaning/effect.
ANEN_EN - Auto-Negotiation Enable
Auto-negotiation (ANEG) is on when this bit is ‘1’. In that case the contents of bits Speed and Duplex
are ignored and the ANEG process determines the link configuration.
PDN - Power down
Setting this bit to ‘1’ will put the PHY in PowerDown mode. In this state the PHY will respond to
management transactions.
MII_DIS - MII DISABLE
Setting this bit will set the PHY to an isolated mode in which it will respond to MII management frames
over the MII management interface but will ignore data on the MII data interface. The internal PHY
is placed in isolation mode at power up and reset. It can be removed from isolation mode by clearing
the MII_DIS bit in the PHY Control Register. If necessary, the internal PHY can be enabled by clearing
the EXT_PHY bit in the Configuration Register.
ANEG_RST - Auto-Negotiation Reset
This bit will return 0 if the PHY does not support ANEG or if ANEG is disabled through the ANEG_EN
bit. If neither of the previous is true, setting this bit to ‘1’ resets the ANEG process. This bit is self
clearing and the PHY will return a ‘1’ until ANEG is initiated, writing a ‘0’ does not affect the ANEG
process.
SMSC LAN91C111-REV B
85
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
DPLX - Duplex mode
When Auto Negotiation is disabled this bit can be used to manually select the link duplex state. Writing
a ‘1’ to this bit selects full duplex while a ‘0’ selects half duplex.
When Auto-Negotiation is enabled reading or writing this bit has no effect.
COLTST - Collision test
Setting a ‘1’ allows for testing of the MII COL signal. ‘0’ allows normal operation.
Reserved:Reserved, Must be 0 for Proper Operation
9.2
Register 1. Status Register
CAP_T4
CAP_TXF
CAP_TXH
CAP_TF
CAP_TH
Reserved
Reserved.
Reserved
R
R
R
R
R
R
R
R
0
1
1
1
1
0
0
0
Reserved
CAP_SUPR
ANEG_ACK
REM_FLT
CAP_ANEG
LINK
JAB
EXREG
R
R
R
R, LH
R
R, LL
R, LH
R
0
0
0
0
1
0
0
1
CAP_T4 - 100BASE-T4 Capable
‘1’ Indicates 100Base-T4 capable PHY, ‘0’ not capable.
CAP_TXF - 100BASE-TX Full Duplex Capable
‘1’ Indicates 100Base-X full duplex capable PHY, ‘0’ not capable.
CAP_TXH - 100BASE-TX Half Duplex Capable
‘1’ Indicates 100Base-X alf duplex capable PHY, ‘0’ not capable.
CAP_TF - 10BASE-T Full Duplex Capable
‘1’ Indicates 10Mbps full duplex capable PHY, ‘0’ not capable.
CAP_TH - 10BASE-T Half Duplex Capable
‘1’ Indicates 10Mbps half duplex capable PHY, ‘0’ not capable.
Reserved:Reserved, Must be 0 for Proper Operation.
CAP_SUPR - MI Preamble Suppression Capable
‘1’ indicates the PHY is able to receive management frames even if not preceded by a preamble. ‘0’
when it is not able.
ANEG_ACK - Auto-Negotiation Acknowledgment
When read as ‘1’ indicate ANEG has been completed and that contents in registers 4,5,6 and 7 are
valid. ‘0’ means ANEG has not completed and contents in registers 4,5,6 and 7 are meaningless. The
PHY returns zero if ANEG is disabled.
Revision 1.8 (07-13-05)
86
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
REM_FLT- Remote Fault Detect
‘1’ indicates a Remote Fault. Latches the ‘1’ condition and is cleared by reading this register or
resetting the PHY.
CAP_ANEG - AutoNegotiation Capable
Indicates the ability (‘1’) to perform ANEG or not (‘0’).
LINK - Link Status
A ‘1’ indicates a valid Link and a ‘0’ and invalid Link. The ‘0’ condition is latched until this register is
read.
JAB - Jabber Detect
Jabber condition detected when ‘1’ for 10Mbps. ‘1’ latched until this register is read or the PHY is reset.
Always ‘0’ for 100Mbps
EXREG - Extended Capability register
‘1’ Indicates extended registers are implemented
9.3
Register 2&3. PHY Identifier Register
These two registers (offsets 2 and 3) provide a 32-bit value unique to the PHY.
REG
BITS
NAME
DEFAULT VALUE
R/W
SOFT RESET
2
15-0
Company ID
0000000000010110
R
Retains Original Value
3
15-10
Company ID
111110
R
Retains Original Value
3
9-4
Manufacturer's ID
000100
R
Retains Original Value
3
3-0
Manufacturer's Revision #
----
R
Retains Original Value
9.4
Register 4. Auto-Negotiation Advertisement Register
NP
ACK
RF
Reserved
Reserved
Reserved
T4
TX_FDX
RW
R
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
1
TX_HDX
10_FDX
10_HDX
Reserved
Reserved
Reserved
Reserved
CSMA
RW
RW
RW
RW
RW
RW
RW
RW
1
1
1
0
0
0
0
1
This register control the values transmitted by the PHY to the remote partner when advertising its
abilities
SMSC LAN91C111-REV B
87
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
NP - Next Page
A ‘1’ indicates the PHY wishes to exchange Next Page information.
ACK - Acknowledge
It is used by the Auto-negotiation function to indicate that a device has successfully received its Link
Partner’s Link code Word.
RF - Remote Fault
When set, an advertisement frame will be sent with the corresponding bit set. This in turn will cause
the PHY receiving it to set the Remote Fault bit in its Status register
T4 - 100BASE-T4
A '1' indicates the PHY is capable of 100BASE-T4
TX_FDX - 100BASE-TX Full Duplex Capable
A '1' indicates the PHY is capable of 100BASE-TX Full Duplex
TX_HDX - 100BASE-TX Half Duplex Capable
A '1' indicates the PHY is capable of 100BASE-TX Half Duplex
10_FDX - 10BASE-T Full Duplex Capable
A '1' indicates the PHY is capable of 10BASE-T Full Duplex
10_HDX - 10BASE-T Half Duplex Capable
A '1' indicates the PHY is capable of 10BASE-T Half Duplex
The management entity sets the value of this field prior to AutoNegotiation.
‘1’ in these bit indicates that the mode of operation that corresponds to these will be acceptable to be
auto-negotiated to. Only modes supported by the PHY can be set.
CSMA
A '1' indicates the PHY is capable of 802.3 CSMA Operation
9.5
Register 5. Auto-Negotiation Remote End Capability Register
NP
ACK
RF
Reserved
Reserved
Reserved
T4
TX_FDX
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
TX_HDX
10_FDX
10_HDX
Reserved
Reserved
Reserved
Reserved
CSMA
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
The bit definitions are analogous to the Auto Negotiation Advertisement Register.
Revision 1.8 (07-13-05)
88
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
9.6
Register 16. Configuration 1- Structure and Bit Definition
LNKDIS
XMTDIS
XMTPDN
Reserved
Reserved
BYPSCR
UNSCDS
EQLZR
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
CABLE
RLVL0
TLVL3
TLVL2
TLVL1
TLVL0
TRF1
TRF0
RW
RW
RW
RW
RW
RW
RW
RW
0
0
1
0
0
0
1
0
LNKDIS:
Link Disable
1 = Receive Link
Detect Function
Disabled (Force Link
Pass)
0 = Normal
XMTDIS:
TP Transmit
1 = TP Transmitter
Disabled
0 = Normal
XMTPDN:
TP Transmit
1 = TP Transmitter
Powered Down
Powerdown
0 = Normal
RESERVED:
RESERVED
Reserved, Must be 0
for Proper Operation
BYPSCR:
Bypass
1 = Bypass
Scrambler/Descram
bler
Scrambler/Descr-
0 = No Bypass
ambler Select
UNSCDS:
Unscrambled Idle
1 = Disable
AutoNegotiation with
devices that transmit
unscrambled
Reception Disable
idle on powerup and
various instances
0 = Enables
AutoNegotiation with
devices that transmit
unscrambled idle on
powerup and various
instances
EQLZR:
SMSC LAN91C111-REV B
Receive Equalizer
89
DATASHEET
1 = Receive
Equalizer Disabled,
Set To 0 Length
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
CABLE
Select
0 = Receive
Equalizer On (For
100MB Mode Only)
Cable Type Select
1 = STP (150 Ohm)
0 = UTP (100 Ohm)
RLVL0
TLVL0-3
Receive Input
1 = Receive Squelch
Levels Reduced By
4.5 dB R/W
Level Adjust
0 = Normal
Transmit Output
See Table 7.2
Level Adjust
TRF0-1
Transmitter
11 = -0.25nS
Rise/Fall Time
10 = +0.0nS
Adjust
01 = +0.25nS
00 = +0.50nS
9.7
Register 17. Configuration 2 - Structure and Bit Definition
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
R
R
R
R
R
R
R
R
1
1
1
1
1
1
1
1
Reserved
Reserved
APOLDIS
JABDIS
MREG
INTMDIO
Reserved
Reserved
R
R
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
APOLDIS:
JABDIS:
MREG:
Revision 1.8 (07-13-05)
Auto Polarity
Disable
Jabber Disable
Select
Multiple Register
Access Enable
90
1 = Auto
Polarity
Correction
Function
Disabled
1 = Auto
Polarity
Correction
Function
Disabled
0 = Normal
0 = Normal
1 = Jabber
Disabled RW
1 = Jabber
Disabled
0 = Enabled
0 = Enabled
1 = Multiple
Register Access
Enabled
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
INTMDIO:
Interrupt
Scheme Select
Reserved:
9.8
0 = No Multiple
Register Access
0 = No
Multiple
Register
Access
1 = Interrupt
Signaled With
MDIO Pulse
During Idle
1 = Interrupt
Signaled
With MDIO
Pulse During
Idle
0 = Interrupt
Not Signaled
On MDIO
0 = Interrupt
Not Signaled
On MDIO
Reserved for
Factory Use
Register 18. Status Output - Structure and Bit Definition
INT
LNKFAIL
LOSSSYNC
CWRD
SSD
ESD
RPOL
JAB
R
R/LT
R/LT
R/LT
R/LT
R/LT
R/LT
R/LT
0
0
0
0
0
0
0
0
SPDDET
DPLXDET
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
R/LT
R/LT
R
R
R
R
R
R
1
0
0
0
0
0
0
0
INT:
Interrupt Detect
1 = Interrupt Bit(s)
Have Changed
Since Last Read
Operation.
0 = No Change
LNKFAIL:
Link Fail Detect
1 = Link Not
Detected
0 = Normal
LOSSSYNC:
CWRD:
Descrambler Loss of
1 = Descrambler
Has Lost
Synchronization
Synchronization
Detect
0 = Normal
Codeword Error
1 = Invalid 4B5B
Code Detected On
Receive Data
0 = Normal
SMSC LAN91C111-REV B
91
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
SSD:
Start Of Stream Error
1 = No Start Of
Stream Delimiter
Detected on Receive
Data
0 = Normal
ESD:
End Of Stream Error
1 = No End Of
Stream Delimiter
Detected on Receive
Data
0 = Normal
RPOL:
Reverse Polarity
Detect
1 = Reverse Polarity
Detected
JAB:
Jabber Detect
1 = Jabber Detected
0 = Normal
SPDDET:
100/10 Speed Detect
1 = Device in
100Mbps Mode
(100BASE-TX)
0 = Device in
10Mbps Mode
(10BASE-T)
DPLXDET:
Duplex Detect
1 = Device In Full
Duplex
0 = Device In Half
Duplex
Reserved:
9.9
Reserved
Reserved for Factory
Use
Register 19. Mask - Structure and Bit Definition
MINT
MLNKFAIL
MLOSSSYN
MCWRD
MSSD
MESD
MRPOL
MJAB
RW
RW
RW
RW
RW
RW
RW
RW
1
1
1
1
1
1
1
1
MSPDDT
MDPLDT
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
RW
RW
RW
RW
RW
RW
RW
RW
1
1
0
0
0
0
0
0
MINT:
Interrupt Mask
Interrupt Detect
1 = Mask Interrupt
For INT In Register
18
0 = No Mask
Revision 1.8 (07-13-05)
92
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
MLNKFAIL:
Interrupt Mask Link
Fail Detect
1 = Mask Interrupt
For LNKFAIL In
Register 18
0 = No Mask
MLOSSSYN:
MCWRD:
Interrupt Mask
Descrambler Loss
1 = Mask Interrupt
For LOSSSYNC In
Register 18
of Synchronization
Detect
0 = No Mask
Interrupt Mask
Codeword Error
1 = Mask Interrupt
For CWRD In
Register 18
0 = No Mask
MSSD:
Interrupt Mask Start
Of Stream Error
1 = Mask Interrupt
For SSD In Register
18
0 = No Mask
MESD:
Interrupt Mask End Of
Stream Error
1 = Mask Interrupt
For ESD In Register
18
0 = No Mask
MRPOL:
Interrupt Mask
Reverse Polarity
Detect
1 = Mask Interrupt
For RPOL In
Register 18
0 = No Mask
MJAB:
Interrupt Mask Jabber
Detect
1 = Mask Interrupt
For JAB In Register
18
0 = No Mask
MSPDDT:
Interrupt Mask 100/10
Speed Detect
1 = Mask Interrupt
For SPDDET In
Register 18
0 = No Mask
MDPLDT:
Interrupt Mask Duplex
Detect
1 = Mask Interrupt
For DPLXDET In
Register 18
0 = No Mask
Reserved:
9.10
Reserved
Reserved for Factory
Use
Register 20. Reserved - Structure and Bit Definition
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
SMSC LAN91C111-REV B
93
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
RW
RW
RW
RW
RW
RW
RW
RW
1
0
1
0
0
0
0
0
Reserved:Reserved for Factory Use
Revision 1.8 (07-13-05)
94
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Chapter 10 Software Driver and Hardware Sequence
Flow
10.1
Software Driver and Hardware Sequence Flow for Power
Management
This section describes the sequence of events and the interaction between the Host Driver and the
Ethernet controller to perform power management. The Ethernet controller has the ability to reduce its
power consumption when the Device is not required to receive or transmit Ethernet Packets.
Power Management is obtained by disabling the EPH clocks, including the Clocks derived from the
Internal PHY block to reduce internal switching, this reducing current consumption.
The Host interface however, will still be accessible. As discussed in Table 10.1 and Table 10.2, the
tables describe the interaction between the EPH and Host driver allowing the Device to transition from
low power state to normal functionality and vice versa.
Table 10.1 Typical Flow Of Events For Placing Device In Low Power Mode
S/W DRIVER
CONTROLLER FUNCTION
1
Disable Transmitter – Clear the TXENA bit of the
Transmit Control Register
Ethernet MAC finishes packet currently being
transmitted.
2
Remove and release all TX completion packet
numbers on the TX completion FIFO.
3
Disable Receiver – Clear the RXEN bit of the
Receive Control Register.
The receiver completes receiving the current frame, if
any, and then goes idle. Ethernet MAC will no longer
receive any packets.
4
Process all Received packets and Issue a Remove
and Release command for each respective RX
packet buffer.
RX and TX completion FIFO’s are now Empty and
all MMU packet numbers are now free.
5
Disable Interrupt sources – Clear the Interrupt
Status Register
Save Device Context – Save all Specific Register
Values set by the driver.
6
Set PDN bit in PHY MI Register 0 to 1
7
8
The internal PHY entered in powerdown mode, the
TP outputs are in high impedance state.
Write to the “EPH Power EN” Bit located in the
configuration register, Bank 1 Offset 0.
9
10
Ethernet MAC gates the RX Clock, TX clock derived
from the Internal PHY. The EPH Clock is also
disabled.
The Ethernet MAC is now in low power mode. The
Host may access all Runtime IO mapped registers.
All IO registers are still accessible. However, the
Host should not read or write to the registers with
the exception of:
Configuration Register
Control Register
Bank Register
SMSC LAN91C111-REV B
95
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Table 10.2 Flow Of Events For Restoring Device In Normal Power Mode
S/W DRIVER
1
CONTROLLER FUNCTION
Write and set (1) the “EPH Power EN” Bit, located in
the configuration register, Bank 1 Offset 0.
2
Ethernet MAC Enables the RX Clock, TX clock
derived from the Internal PHY. The EPH Clock is
also enabled.
3
Write the PDN bit in PHY MI Register 0 to 0
The PHY is then set in isolation mode (MII_DIS bit
is set). Need to clear this MII_DIS bit; and, need to
wait for 500 ms for the PHY to restore normal.
4
Internal PHY entered normal operation mode
5
Issue MMU Reset Command
6
Restore Device Register Level Context.
7
Enable Transmitter – Set the TXENA bit of the
Transmit Control Register
Ethernet MAC can now transmit Ethernet Packets.
8
Enable Receiver – Set (1) the RXEN bit of the
Receive Control Register.
Ethernet MAC is now able to receive Packets.
9
Ethernet MAC is now restored for normal operation.
10.2
Typical Flow of Events for Transmit (Auto Release = 0)
S/W DRIVER
MAC SIDE
1
ISSUE ALLOCATE MEMORY FOR TX - N BYTES the MMU attempts to allocate N bytes of RAM.
2
WAIT FOR SUCCESSFUL COMPLETION CODE Poll until the ALLOC INT bit is set or enable its mask
bit and wait for the interrupt. The TX packet number
is now at the Allocation Result Register.
3
LOAD TRANSMIT DATA - Copy the TX packet
number into the Packet Number Register. Write the
Pointer Register, then use a block move operation
from the upper layer transmit queue into the Data
Register.
4
ISSUE "ENQUEUE PACKET NUMBER TO TX FIFO"
- This command writes the number present in the
Packet Number Register into the TX FIFO. The
transmission is now enqueued. No further CPU
intervention is needed until a transmit interrupt is
generated.
5
Revision 1.8 (07-13-05)
The enqueued packet will be transferred to the MAC
block as a function of TXENA (nTCR) bit and of the
deferral process (1/2 duplex mode only) state.
96
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
S/W DRIVER
MAC SIDE
6
7
Upon transmit completion the first word in memory is
written with the status word. The packet number is
moved from the TX FIFO into the TX completion
FIFO. Interrupt is generated by the TX completion
FIFO being not empty.
If a TX failure occurs on any packets, TX INT is
generated and TXENA is cleared, transmission
sequence stops. The packet number of the failure
packet is presented at the TX FIFO PORTS Register.
SERVICE INTERRUPT - Read Interrupt Status
Register. If it is a transmit interrupt, read the TX FIFO
Packet Number from the FIFO Ports Register. Write
the packet number into the Packet Number Register.
The corresponding status word is now readable from
memory. If status word shows successful
transmission, issue RELEASE packet number
command to free up the memory used by this packet.
Remove packet number from completion FIFO by
writing TX INT Acknowledge Register.
Option 1) Release the packet.
Option 2) Check the transmit status in the EPH
STATUS Register, write the packet number of the
current packet to the Packet Number Register, reenable TXENA, then go to step 4 to start the TX
sequence again.
10.3
Typical Flow of Events for Transmit (Auto Release = 1)
S/W DRIVER
MAC SIDE
1
ISSUE ALLOCATE MEMORY FOR TX - N BYTES the MMU attempts to allocate N bytes of RAM.
2
WAIT FOR SUCCESSFUL COMPLETION CODE Poll until the ALLOC INT bit is set or enable its mask
bit and wait for the interrupt. The TX packet number
is now at the Allocation Result Register.
3
LOAD TRANSMIT DATA - Copy the TX packet
number into the Packet Number Register. Write the
Pointer Register, then use a block move operation
from the upper layer transmit queue into the Data
Register.
4
ISSUE "ENQUEUE PACKET NUMBER TO TX FIFO"
- This command writes the number present in the
Packet Number Register into the TX FIFO. The
transmission is now enqueued. No further CPU
intervention is needed until a transmit interrupt is
generated.
5
The enqueued packet will be transferred to the MAC
block as a function of TXENA (nTCR) bit and of the
deferral process (1/2 duplex mode only) state.
6
Transmit pages are released by transmit completion.
7
The MAC generates a TXEMPTY interrupt upon a
completion of a sequence of enqueued packets.
If a TX failure occurs on any packets, TX INT is
generated and TXENA is cleared, transmission
sequence stops. The packet number of the failure
packet is presented at the TX FIFO PORTS Register.
SMSC LAN91C111-REV B
97
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
S/W DRIVER
8
MAC SIDE
SERVICE INTERRUPT – Read Interrupt Status
Register, exit the interrupt service routine.
Option 1) Release the packet.
Option 2) Check the transmit status in the EPH
STATUS Register, write the packet number of the
current packet to the Packet Number Register, reenable TXENA, then go to step 4 to start the TX
sequence again.
10.4
Typical Flow of Event For Receive
S/W DRIVER
1
MAC SIDE
ENABLE RECEPTION - By setting the RXEN bit.
2
A packet is received with matching address. Memory
is requested from MMU. A packet number is
assigned to it. Additional memory is requested if
more pages are needed.
3
The internal DMA logic generates sequential
addresses and writes the receive words into memory.
The MMU does the sequential to physical address
translation. If overrun, packet is dropped and
memory is released.
4
When the end of packet is detected, the status word
is placed at the beginning of the receive packet in
memory. Byte count is placed at the second word. If
the CRC checks correctly the packet number is
written into the RX FIFO. The RX FIFO, being not
empty, causes RCV INT (interrupt) to be set. If CRC
is incorrect the packet memory is released and no
interrupt will occur.
5
SERVICE INTERRUPT - Read the Interrupt Status
Register and determine if RCV INT is set. The next
receive packet is at receive area. (Its packet number
can be read from the FIFO Ports Register). The
software driver can process the packet by accessing
the RX area, and can move it out to system memory
if desired. When processing is complete the CPU
issues the REMOVE AND RELEASE FROM TOP OF
RX command to have the MMU free up the used
memory and packet number.
Revision 1.8 (07-13-05)
98
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
ISR
Save Bank Select & Address
Ptr Registers
Mask SMC91C111
Interrupts
Read Interrupt Register
No
Yes
RX INTR?
Yes
TX INTR?
Call TX INTR or TXEMPTY
INTR
No
Call RXINTR
Get Next TX
Yes
ALLOC INTR?
Packet
Available for
Transmission?
No
Yes
Write Allocated Pkt # into
Packet Number Reg.
No
Call ALLOCATE
Write Ad Ptr Reg. & Copy Data
& Source Address
Enqueue Packet
EPH INTR?
Yes
No
Set "Ready for Packet" Flag
Call EPH INTR
Return Buffers to Upper Layer
MDINT?
Disable Allocation Interrupt
Mask
Yes
Restore Address Pointer &
Bank Select Registers
Call MDINT
Unmask SMC91C111
Interrupts
Exit ISR
Figure 10.1 Interrupt Service Routine
SMSC LAN91C111-REV B
99
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
RX INTR
Write Ad. Ptr. Reg. & Read
Word 0 from RAM
Yes
Destination
Multicast?
No
Read Words 2, 3, 4 from RAM
for Address Filtering
No
No
Address
Filtering Pass?
Status Word
OK?
Yes
Yes
Do Receive Lookahead
Get Copy Specs from Upper
Layer
No
Okay to
Copy?
Yes
Copy Data Per Upper Layer
Specs
Issue "Remove and Release"
Command
Return to ISR
Figure 10.2 RX INTR
Revision 1.8 (07-13-05)
100
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
TX Interrupt With AUTO_RELEASE = FALSE
1. Save the Packet Number Register
Saved_PNR = Read Byte (Bank 2, Offset 2)
2. Read the EPH Status Register
Temp = Read (Bank 0, Offset 2)
3. Acknowledge TX Interrupt
Write Byte (0x02, (Bank 2, Offset C));
4. Check for Status of Transmission
If ( Temp AND 0x0001)
{
//If Successful Transmission
Step 4.1.1: Issue MMU Release (Release Specific Packet)
Write (0x00A0, (Bank2, Offset 0));
Step 4.1.2: Return from the routine
}
else
{
//Transmission has FAILED
// Now we can either release or re-enqueue the packet
Step 4.2.1: Get the packet to release/re-enqueue, stored in FIFO
Temp = Read (Bank 2, Offset 4)
Temp = Temp & 0x003F
Step 4.2.2: Write to the PNR
Write (Temp, (Bank2, Offset 2))
Step 4.2.3
// Option 1: Release the packet
Write (0x00A0, (Bank2, Offset 0));
//Option 2: Re-Enqueue the packet
Write (0x00C0, (Bank2, Offset 0));
Step 4.2.4: Re-Enable Transmission
Temp = Read(Bank0, Offset 0);
Temp = Temp2 OR 0x0001
Write (Temp2, (Bank 0, Offset 0));
Step 4.2.5: Return from the routine
}
5. Restore the Packet Number Register
Write Byte (Saved_PNR, (Bank 2, Offset 2))
Figure 10.3 TX INTR
SMSC LAN91C111-REV B
101
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
TXEMPTY INTR
Write Acknowledge Reg. with
TXEMPTY Bit Set
Read TXEMPTY & TX INTR
TXEMPTY = 0
&
TXINT = 0
(Waiting for Completion)
TXEMPTY = X
&
TXINT = 1
(Transmission Failed)
TXEMPTY = 1
&
TXINT = 0
(Everything went through
successfully)
Read Pkt. # Register & Save
Write Address Pointer
Register
Read Status Word from RAM
Update Statistics
Issue "Release" Command
Update Variables
Acknowledge TXINTR
Re-Enable TXENA
Restore Packet Number
Return to ISR
Figure 10.4 TXEMPTY INTR (Assumes Auto Release Option Selected)
Revision 1.8 (07-13-05)
102
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
D R IV E R S E N D
A L L O C ATE
C h o o se B a n k S e le ct
R e g iste r 2
Issu e "A llo ca te M e m o ry"
C o m m a n d to M M U
C a ll A L L O C ATE
R e a d In te rru p t S ta tu s R e g iste r
E xit D rive r S e n d
Ye s
A llo ca tio n
Pa sse d ?
No
R e a d A llo ca tio n R e su lt
R e g iste r
W rite A llo ca te d Pa cke t in to
Pa cke t # R e g iste r
S to re D a ta B u ffe r Po in te r
W rite A d d re ss Po in te r R e g iste r
C le a r "R e a d y fo r Pa cke t" Fla g
C o py Pa rt o f TX D a ta Pa cke t
in to R A M
E n a ble A llo ca tio n In te rru p t
W rite S o u rce A d d re ss in to
P ro p e r L o ca tio n
C o py R e m a in in g T X D a ta
Pa cke t in to R A M
E n q u e u e Pa cke t
S e t "R e a d y fo r Pa cke t" Fla g
R e tu rn B u ffe rs to U p p e r L aye r
Re tu rn
Figure 10.5 Drive Send and Allocate Routines
MEMORY PARTITIONING
Unlike other controllers, the LAN91C111 does not require a fixed memory partitioning between transmit
and receive resources. The MMU allocates and de-allocates memory upon different events. An
additional mechanism allows the CPU to prevent the receive process from starving the transmit
memory allocation.
Memory is always requested by the side that needs to write into it, that is: the CPU for transmit or the
MAC for receive. The CPU can control the number of bytes it requests for transmit but it cannot
determine the number of bytes the receive process is going to demand. Furthermore, the receive
process requests will be dependent on network traffic, in particular on the arrival of broadcast and
SMSC LAN91C111-REV B
103
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
multicast packets that might not be for the node, and that are not subject to upper layer software flow
control.
INTERRUPT GENERATION
The interrupt strategy for the transmit and receive processes is such that it does not represent the
bottleneck in the transmit and receive queue management between the software driver and the
controller. For that purpose there is no register reading necessary before the next element in the
queue (namely transmit or receive packet) can be handled by the controller. The transmit and receive
results are placed in memory.
The receive interrupt will be generated when the receive queue (FIFO of packets) is not empty and
receive interrupts are enabled. This allows the interrupt service routine to process many receive
packets without exiting, or one at a time if the ISR just returns after processing and removing one.
There are two types of transmit interrupt strategies:
1. One interrupt per packet.
2. One interrupt per sequence of packets.
The strategy is determined by how the transmit interrupt bits and the AUTO RELEASE bit are used.
TX INT bit - Set whenever the TX completion FIFO is not empty.
TX EMPTY INT bit - Set whenever the TX FIFO is empty.
AUTO RELEASE - When set, successful transmit packets are not written into completion FIFO, and
their memory is released automatically.
1. One interrupt per packet: enable TX INT, set AUTO RELEASE=0. The software driver can find the
completion result in memory and process the interrupt one packet at a time. Depending on the
completion code the driver will take different actions. Note that the transmit process is working in
parallel and other transmissions might be taking place. The LAN91C111 is virtually queuing the
packet numbers and their status words.
In this case, the transmit interrupt service routine can find the next packet number to be serviced by
reading the TX FIFO PACKET NUMBER at the FIFO PORTS register. This eliminates the need for the
driver to keep a list of packet numbers being transmitted. The numbers are queued by the LAN91C111
and provided back to the CPU as their transmission completes.
2. One interrupt per sequence of packets: Enable TX EMPTY INT and TX INT, set AUTO
RELEASE=1. TX EMPTY INT is generated only after transmitting the last packet in the FIFO.
TX INT will be set on a fatal transmit error allowing the CPU to know that the transmit process has
stopped and therefore the FIFO will not be emptied.
This mode has the advantage of a smaller CPU overhead, and faster memory de-allocation. Note that
when AUTO RELEASE=1 the CPU is not provided with the packet numbers that completed
successfully.
Note: The pointer register is shared by any process accessing the LAN91C111 memory. In order to
allow processes to be interruptible, the interrupting process is responsible for reading the
pointer value before modifying it, saving it, and restoring it before returning from the interrupt.
Typically there would be three processes using the pointer:
1. Transmit loading (sometimes interrupt driven)
2. Receive unloading (interrupt driven)
3. Transmit Status reading (interrupt driven).
1) and 3) also share the usage of the Packet Number Register. Therefore saving and restoring the
PNR is also required from interrupt service routines.
Revision 1.8 (07-13-05)
104
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
INTERRUPT
'NOT EMPTY'
STATUS REGISTER
RCV
INT
TWO
OPTIONS
PACKET NUMBER
RX FIFO
PACKET NUMBER
REGISTER
TX EMPTY
INT
TX
INT
ALLOC
INT
RX
FIFO
TX
FIFO
'EMPTY'
RX PACKET
NUMBER
TX COMPLETION
FIFO
'NOT EMPTY'
TX DONE
PACKET NUMBER
CSMA ADDRESS
CPU ADDRESS
CSMA/CD
LOGICAL
ADDRESS
PACKET #
MMU
M.S. BIT ONLY
PACK # OUT
PHYSICAL ADDRESS
RAM
Figure 10.6 Interrupt Generation for Transmit, Receive, MMU
SMSC LAN91C111-REV B
105
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Revision 1.8 (07-13-05)
106
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Chapter 11 Board Setup Information
The following parameters are obtained from the EEPROM as board setup information:
■
ETHERNET INDIVIDUAL ADDRESS
■
I/O BASE ADDRESS
■
MII INTERFACE
All the above mentioned values are read from the EEPROM upon hardware reset. Except for the
INDIVIDUAL ADDRESS, the value of the IOS switches determines the offset within the EEPROM for
these parameters, in such a way that many identical boards can be plugged into the same system by
just changing the IOS jumpers.
In order to support a software utility based installation, even if the EEPROM was never programmed,
the EEPROM can be written using the LAN91C111. One of the IOS combination is associated with a
fixed default value for the key parameters (I/O BASE) that can always be used regardless of the
EEPROM based value being programmed. This value will be used if all IOS pins are left open or pulled
high.
The EEPROM is arranged as a 64 x 16 array. The specific target device is the 9346 1024-bit Serial
EEPROM. All EEPROM accesses are done in words. All EEPROM addresses in the spec are
specified as word addresses.
REGISTER
EEPROM WORD ADDRESS
Configuration Register
IOS Value * 4
Base Register
(IOS Value * 4) + 1
INDIVIDUAL ADDRESS 20-22 hex
If IOS2-IOS0 = 7, only the INDIVIDUAL ADDRESS is read from the EEPROM. Currently assigned
values are assumed for the other registers. These values are default if the EEPROM read operation
follows hardware reset.
The EEPROM SELECT bit is used to determine the type of EEPROM operation: a) normal or b)
general purpose register.
1. NORMAL EEPROM OPERATION - EEPROM SELECT bit = 0
On EEPROM read operations (after reset or after setting RELOAD high) the CONFIGURATION
REGISTER and BASE REGISTER are updated with the EEPROM values at locations defined by the
IOS2-0 pins. The INDIVIDUAL ADDRESS registers are updated with the values stored in the
INDIVIDUAL ADDRESS area of the EEPROM.
On EEPROM write operations (after setting the STORE bit) the values of the CONFIGURATION
REGISTER and BASE REGISTER are written in the EEPROM locations defined by the IOS2-IOS0
pins.
The three least significant bits of the CONTROL REGISTER (EEPROM SELECT, RELOAD and
STORE) are used to control the EEPROM. Their values are not stored nor loaded from the EEPROM.
2. GENERAL PURPOSE REGISTER - EEPROM SELECT bit = 1
On EEPROM read operations (after setting RELOAD high) the EEPROM word address defined by the
POINTER REGISTER 6 least significant bits is read into the GENERAL PURPOSE REGISTER.
On EEPROM write operations (after setting the STORE bit) the value of the GENERAL PURPOSE
REGISTER is written at the EEPROM word address defined by the POINTER REGISTER 6 least
significant bits.
RELOAD and STORE are set by the user to initiate read and write operations respectively. Polling the
value until read low is used to determine completion. When an EEPROM access is in progress the
SMSC LAN91C111-REV B
107
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
STORE and RELOAD bits of CTR will readback as both bits high. No other bits of the LAN91C111 can
be read or written until the EEPROM operation completes and both bits are clear. This mechanism is
also valid for reset initiated reloads.
Note: If no EEPROM is connected to the LAN91C111, for example for some embedded applications,
the ENEEP pin should be grounded and no accesses to the EEPROM will be attempted.
Configuration, Base, and Individual Address assume their default values upon hardware reset
and the CPU is responsible for programming them for their final value.
Revision 1.8 (07-13-05)
108
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
16 BITS
IOS2-0
WORD ADDRESS
000
0h
CONFIGURATION REG.
1h
BASE REG.
4h
CONFIGURATION REG.
5h
BASE REG.
8h
CONFIGURATION REG.
9h
BASE REG.
Ch
CONFIGURATION REG.
Dh
BASE REG.
10h
CONFIGURATION REG.
11h
BASE REG.
14h
CONFIGURATION REG.
15h
BASE REG.
18h
CONFIGURATION REG.
19h
BASE REG.
20h
IA0-1
21h
IA2-3
22h
IA4-5
001
010
011
100
101
110
XXX
Figure 11.1 64 X 16 Serial EEPROM Map
SMSC LAN91C111-REV B
109
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Revision 1.8 (07-13-05)
110
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Chapter 12 Application Considerations
The LAN91C111 is envisioned to fit a few different bus types. This section describes the basic
guidelines, system level implications and sample configurations for the most relevant bus types. All
applications are based on buffered architectures with a private SRAM bus.
FAST ETHERNET SLAVE ADAPTER
Slave non-intelligent board implementing 100 Mbps and 10 Mbps speeds.
Adapter requires:
1. LAN91C111 chip
2. Serial EEPROM (93C46)
3. Some bus specific glue logic
Target systems:
1. VL Local Bus 32 bit systems
2. High-end ISA or non-burst EISA machines
3. EISA 32 bit slave
VL Local Bus 32 Bit Systems
On VL Local Bus and other 32 bit embedded systems the LAN91C111 is accessed as a 32 bit
peripheral in terms of the bus interface. All registers except the DATA REGISTER will be accessed
using byte or word instructions. Accesses to the DATA REGISTER could use byte, word, or dword
instructions.
Table 12.1 VL Local Bus Signal Connections
VL BUS
SIGNAL
LAN91C111
SIGNAL
NOTES
A2-A15
A2-A15
Address bus used for I/O space and register decoding, latched by nADS
rising edge, and transparent on nADS low time.
M/nIO
AEN
Qualifies valid I/O decoding - enabled access when low. This signal is
latched by nADS rising edge and transparent on nADS low time.
W/nR
W/nR
Direction of access. Sampled by the LAN91C111 on first rising clock that
has nCYCLE active. High on writes, low on reads.
nRDYRTN
nRDYRTN
Ready return. Direct connection to VL bus.
nLRDY
nSRDY and some
logic
nSRDY has the appropriate functionality and timing to create the VL
nLRDY except that nLRDY behaves like an open drain output most of
the time.
LCLK
LCLK
Local Bus Clock. Rising edges used for synchronous bus interface
transactions.
nRESET
RESET
Connected via inverter to the LAN91C111.
nBE0 nBE1
nBE2 nBE3
nBE0 nBE1 nBE2
nBE3
Byte enables. Latched transparently by nADS rising edge.
nADS
nADS, nCYCLE
Address Strobe is connected directly to the VL bus. nCYCLE is created
typically by using nADS delayed by one LCLK.
IRQn
INTR0
Typically uses the interrupt lines on the ISA edge connector of VL bus
SMSC LAN91C111-REV B
111
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Table 12.1 VL Local Bus Signal Connections (continued)
VL BUS
SIGNAL
LAN91C111
SIGNAL
NOTES
D0-D31
D0-D31
32 bit data bus. The bus byte(s) used to access the device are a function
of nBE0-nBE3:
nBE0
0
nBE1
0
nBE2
nBE3
0
0
Double word access
0
0
1
1
Low word access
1
1
0
0
High word access
0
1
1
1
Byte 0 access
1
0
1
1
Byte 1 access
1
1
0
1
Byte 2 access
1
1
1
0
Byte 3 access
Not used = tri-state on reads, ignored on writes. Note that nBE2 and
nBE3 override the value of A1, which is tied low in this application.
nLDEV
nLDEV
nLDEV is a totem pole output. nLDEV is active on valid decodes of A15A4 and AEN=0.
UNUSED PINS
VCC
nRD nWR
GND
A1 nVLBUS
OPEN
nDATCS
Revision 1.8 (07-13-05)
112
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
VLBUS
W/nR
W/nR
A2-A15
A2-A15
LCLK
LCLK
M/nIO
AEN
nRESET
RESET
IRQn
LAN91C111
INTR0
D0-D31
D0-D31
nRDYRTN
nRDYRTN
nBE0-nBE3
nBE0-nBE3
nADS
nADS
Delay 1 LCLK
nCYCLE
nSRDY
nLRDY
nLDEV
O.C.
simulated
O.C.
nLDEV
Figure 12.1 LAN91C111 on VL BUS
HIGH-END ISA OR NON-BURST EISA MACHINES
On ISA machines, the LAN91C111 is accessed as a 16 bit peripheral. The signal connections are listed
in the following table:
Table 12.2 High-End ISA or Non-Burst EISA Machines Signal Connectors
ISA BUS
SIGNAL
LAN91C111
SIGNAL
NOTES
A1-A15
A1-A15
Address bus used for I/O space and register decoding.
AEN
AEN
Qualifies valid I/O decoding - enabled access when low.
nIORD
nRD
I/O Read strobe - asynchronous read accesses. Address is valid before
leading edge.
SMSC LAN91C111-REV B
113
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Table 12.2 High-End ISA or Non-Burst EISA Machines Signal Connectors (continued)
ISA BUS
SIGNAL
LAN91C111
SIGNAL
NOTES
nIOWR
nWR
I/O Write strobe - asynchronous write access. Address is valid before
leading edge. Data is latched on trailing edge.
IOCHRDY
ARDY
This signal is negated on leading nRD, nWR if necessary. It is then
asserted on CLK rising edge after the access condition is satisfied.
RESET
RESET
A0
nBE0
nSBHE
nBE1
IRQn
INTR0
D0-D15
D0-D15
16 bit data bus. The bus byte(s) used to access the device are a function
of nBE0 and nBE1:
nBE0
nBE1
D0-D7
D8-D15
0
0
Lower
Upper
0
1
Lower
Not used
1
0
Not used
Upper
Not used = tri-state on reads, ignored on writes
nIOCS16
nLDEV buffered
nLDEV is a totem pole output. Must be buffered using an open collector
driver. nLDEV is active on valid decodes of A15-A4 and AEN=0.
UNUSED PINS
GND
nADS
VCC
nBE2, nBE3,
nCYCLE, W/nR,
nRDYRTN, LCLK
Revision 1.8 (07-13-05)
No upper word access.
114
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
ISA BUS
A1-A15, AEN
A1-A15, AEN
RESET
RESET
nBE2, nBE3
VCC
D0-D15
D0-D15
LAN91C111
INTR0
IRQ
nIORD
nRD
nIOWR
nWR
A0
nBE0
nBE1
nSBHE
nLDEV
nIOCS16
O.C.
Figure 12.2 LAN91C111 on ISA BUS
EISA 32 BIT SLAVE
On EISA the LAN91C111 is accessed as a 32 bit I/O slave, along with a Slave DMA type "C" data
path option. As an I/O slave, the LAN91C111 uses asynchronous accesses. In creating nRD and nWR
inputs, the timing information is externally derived from nCMD edges. Given that the access will be at
least 1.5 to 2 clocks (more than 180ns at least) there is no need to negate EXRDY, simplifying the
EISA interface implementation. As a DMA Slave, the LAN91C111 accepts burst transfers and is able
to sustain the peak rate of one doubleword every BCLK. Doubleword alignment is assumed for DMA
transfers. The LAN91C111 will sample EXRDY and postpone DMA cycles if the memory cycle solicits
wait states.
Table 12.3 EISA 32 Bit Slave Signal Connections
EISA BUS
SIGNAL
LAN91C111
SIGNAL
NOTES
LA2-LA15
A2-A15
Address bus used for I/O space and register decoding, latched by
nADS (nSTART) trailing edge.
M/nIO
AEN
AEN
Qualifies valid I/O decoding - enabled access when low. These
signals are externally ORed. Internally the AEN pin is latched by
nADS rising edge and transparent while nADS is low.
Latched W-R
combined with
nCMD
nRD
I/O Read strobe - asynchronous read accesses. Address is valid
before its leading edge. Must not be active during DMA bursts if
DMA is supported.
SMSC LAN91C111-REV B
115
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Table 12.3 EISA 32 Bit Slave Signal Connections (continued)
EISA BUS
SIGNAL
LAN91C111
SIGNAL
Latched W-R
combined with
nCMD
nWR
I/O Write strobe - asynchronous write access. Address is valid
before leading edge . Data latched on trailing edge. Must not be
active during DMA bursts if DMA is supported.
nSTART
nADS
Address strobe is connected to EISA nSTART.
RESDRV
RESET
nBE0 nBE1 nBE2
nBE3
nBE0 n BE1 nBE2
nBE3
Byte enables. Latched on nADS rising edge.
IRQn
INTR0
Interrupts used as active high edge triggered
D0-D31
D0-D31
32 bit data bus. The bus byte(s) used to access the device are a
function of nBE0-nBE3:
NOTES
nBE0
nBE1
nBE2
nBE3
0
0
0
0
Double word access
0
0
1
1
Low word access
1
1
0
0
High word access
0
1
1
1
Byte 0 access
1
0
1
1
Byte 1 access
1
1
0
1
Byte 2 access
1
1
1
0
Byte 3 access
Not used = tri-state on reads, ignored on writes. Note that nBE2 and
nBE3 override the value of A1, which is tied low in this application.
Other combinations of nBE are not supported by the LAN91C111.
Software drivers are not anticipated to generate them.
nEX32
nNOWS
(optional additional
logic)
nLDEV
nLDEV is a totem pole output. nLDEV is active on valid decodes of
LAN91C111 pins A15-A4, and AEN=0. nNOWS is similar to nLDEV
except that it should go inactive on nSTART rising. nNOWS can be
used to request compressed cycles (1.5 BCLK long, nRD/nWR will
be 1/2 BCLK wide).
THE FOLLOWING SIGNALS SUPPORT SLAVE DMA TYPE "C" BURST CYCLES
BCLK
LCLK
EISA Bus Clock. Data transfer clock for DMA bursts.
nDAK<n>
nDATACS
DMA Acknowledge. Active during Slave DMA cycles. Used by the
LAN91C111 as nDATACS direct access to data path.
nIORC
W/nR
Indicates the direction and timing of the DMA cycles. High during
LAN91C111 writes, low during LAN91C111 reads.
nIOWC
nCYCLE
Indicates slave DMA writes.
nEXRDY
nRDYRTN
EISA bus signal indicating whether a slave DMA cycle will take place
on the next BCLK rising edge, or should be postponed. nRDYRTN
is used as an input in the slave DMA mode to bring in EXRDY.
UNUSED PINS
VCC
nVLBUS
GND
A1
Revision 1.8 (07-13-05)
116
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
EISA BUS
LA2- LA15
A2-A15
RESET
RESET
AEN
AEN
M/nIO
D0-D31
D0-D31
INTR0
IRQn
LAN91C111
nBE[0:3]
nCMD
nWR
nBE[0:3]
nRD
LATCH
+
gates
nWR
LCLK
BCLK
nSTART
nADS
nLDEV
nEX32
O.C.
Figure 12.3 LAN91C111 on EISA BUS
SMSC LAN91C111-REV B
117
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Revision 1.8 (07-13-05)
118
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Chapter 13 Operational Description
13.1
Maximum Guaranteed Ratings*
Operating Temperature Range
0°C to +85°C for LAN91C111 (-40°C to 85°C for
LAN91C111I)
Storage Temperature Range
-55C° to + 150°C
Lead Temperature Range (soldering, 10
seconds)
+325°C
Positive Voltage on any pin, with respect to
Ground
VCC + 0.3V
Negative Voltage on any pin, with respect to
Ground
-0.3V
Maximum VCC
+5V
*Stresses above those listed above could cause permanent damage to the device. This is a stress
rating only and functional operation of the device at any other condition above those indicated in the
operation sections of this specification is not implied.
Note: When powering this device from laboratory or system power supplies, it is important that the
Absolute Maximum Ratings not be exceeded or device failure can result. Some power supplies
exhibit voltage spikes on their outputs when the AC power is switched on or off. In addition,
voltage transients on the AC power line may appear on the DC output. If this possibility exists,
it is suggested that a clamp circuit be used.
13.2
DC Electrical Characteristics
(VCC = +3.3.0 V ± 10%)
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
COMMENTS
0.8
V
TTL Levels
I Type Input Buffer
Low Input Level
VILI
High Input Level
VIHI
2.0
V
IS Type Input Buffer
Low Input Level
VILIS
High Input Level
VIHIS
Schmitt Trigger Hysteresis
VHYS
0.8
2.2
250
V
Schmitt Trigger
V
Schmitt Trigger
mV
ICLK Input Buffer
Low Input Level
VILCK
High Input Level
VIHCK
SMSC LAN91C111-REV B
0.8
2.2
V
V
119
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
PARAMETER
Input Leakage
(All I and IS buffers except
pins with
pullups/pulldowns)
Low Input Leakage
High Input Leakage
SYMBOL
MIN
IIL
TYP
MAX
UNITS
COMMENTS
-10
+10
µA
VIN = 0
IIH
-10
+10
µA
VIN = VCC
IIL
-110
µA
VIN = 0
+110
µA
VIN = VCC
0.4
V
IOL = 6 mA
V
IOH = -4 mA
+10
µA
VIN = 0 to VCC
0.4
V
IOL = 6 mA
V
IOH = -4 mA
+10
µA
VIN = 0 to VCC
0.4
V
IOL = 20 mA
V
IOH = -10 mA
+10
µA
VIN = 0 to VCC
0.4
V
IOL = 35 mA
V
IOH = -15 mA
+10
µA
VIN = 0 to VCC
0.4
V
IOL = 35 mA
V
IOH = -15 mA
+10
µA
VIN = 0 to VCC
0.4
V
IOL = 35 mA
V
IOH = -15 mA
µA
VIN = 0 to VCC
IP Type Buffers
Input Current
-45
ID Type Buffers
Input Current
IIH
+45
O4 Type Buffer
Low Output Level
VOL
High Output Level
VOH
2.4
Output Leakage
IOL
-10
I/O4 Type Buffer
Low Output Level
VOL
High Output Level
VOH
2.4
Output Leakage
IOL
-10
O12 Type Buffer
Low Output Level
VOL
High Output Level
VOH
2.4
Output Leakage
IOL
-10
O16 Type Buffer
Low Output Level
VOL
High Output Level
VOH
2.4
Output Leakage
IOL
-10
O24 Type Buffer
Low Output Level
VOL
High Output Level
VOH
2.4
Output Leakage
IOL
-10
I/O24 Type Buffer
Low Output Level
VOL
High Output Level
VOH
2.4
Output Leakage
IOL
-10
Revision 1.8 (07-13-05)
+10
120
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
COMMENTS
0.4
V
IOL = 4 mA
V
na
+10
µA
VIN = 0 to VCC
Dynamic Current
(Assuming internal PHY is
used)
I/OD Type Buffer
Low Output Level
VOL
High Output Level
VOH
2.4
Output Leakage
IOL
-10
Supply Current Active
Powerdown Supply Current
ICC
100
140
mA
IPDN
15
38
mA
Internal PHY in
Powerdown mode
14
36
mA
Internal MAC+PHY in
Powerdown mode
CAPACITANCE TA = 25°C; fc = 1MHz; VCC = 3.3V
LIMITS
PARAMETER
SYMBOL
Clock Input Capacitance
MIN
TYP
MAX
UNIT
TEST CONDITION
CIN
20
pF
All pins except pin
under test tied to
AC ground
Input Capacitance
CIN
10
pF
Output Capacitance
COUT
20
pF
CAPACITIVE LOAD ON OUTPUTS
ARDY, D0-D31 (non VLBUS)
45 pF
D0-D31 in VLBUS
45 pF
All other outputs
45 pF
SMSC LAN91C111-REV B
121
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
13.3
Twisted Pair Characteristics, Transmit
VDD = 3.3v +/- 5%
RBIAS = 11K +/- 1 %, no load
LIMIT
SYM
Tov
PARAMETER
TP Differential Output
Voltage
UNIT
CONDITIONS
1.050
Vpk
100 Mbps, UTP Mode,
100 Ohm Load
1.225
1.285
Vpk
100 Mbps, STP Mode,
150 Ohm Load
2.2
2.5
2.8
Vpk
10 Mbps, UTP Mode,
100 Ohm Load
2.694
3.062
3.429
Vpk
10 Mbps, STP Mode,
150 Ohm Load
MIN
TYP
MAX
0.950
1.000
1.165
Tovs
TP Differential Output
Voltage Symmetry
98
102
%
100 Mbps, Ratio of Positive And
Negative Amplitude Peaks on TPO±
TORF
TP Differential Output
Rise And Fall Time
3.0
5.0
nS
100 Mbps
TRFADJ [1:0] = 10
TORFS
TP Differential Output
Rise And Fall Time
Symmetry
+/-0.5
ToDC
TP Differential Output
Duty Cycle Distortion
+/0.25
nS
100 Mbps, Output Data=0101... NRZ
Pattern Unscrambled, Measure At
50% Points
ToJ
TP Differential Output
Jitter
+/-1.4
nS
100 Mbps, Output Data=scrambled /H/
Too
TP Differential Output
Overshoot
5.0
%
100 Mbps
TOVT
TP Differential Output
Voltage Template
See Figure 7.4
10 Mbps
TSOI
TP Differential Output
SOI Voltage
Template
See Figure 7.6
10 Mbps
TLPT
TP Differential Output
Link Pulse Voltage
Template
See Figure 7.7
10 Mbps, NLP and FLP
TOIV
TP Differential Output
Idle Voltage
TOIA
TP Output Current
Revision 1.8 (07-13-05)
nS
100 Mbps, Difference Between Rise
and Fall Times on TPO±
+/-50
mV
10 Mbps.
38
40
42
mA pk
100 Mbps, UTP with TLVL[3:0]=1000
31.06
32.66
34.26
mA pk
100 Mbps, STP with TLVL[3:0]=1000
88
100
112
mA pk
10 Mbps, UTP with TLVL[3:0]=1000
71.86
81.64
91.44
mA pk
10 Mbps, STP with TLVL[3:0]=1000
122
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
LIMIT
SYM
PARAMETER
UNIT
MIN
TOIR
TP Output Current
Adjustment Range
TYP
0.80
1.2
VDD = 3.3V, Adjustable with RBIAS,
relative to TOIA with RBIAS=11K
0.86
1.16
VDD = 3.3V, Adjustable with LVL[3:0]
Relative to Value at TLVL[3:0]=1000
TORA
TP Output Current
TLVL Step Accuracy
TOR
TP Output
Resistance
10K
Ohm
TOC
TP Output
Capacitance
15
pF
13.4
CONDITIONS
MAX
+/-50
%
Relative to Ideal Values in Table 3.
Table 3 Values Relative to Output with
TLVL[3:0]=1000.
Twisted Pair Characteristics, Receive
Unless otherwise noted, all test conditions are as follows:
■
Vcc = 3.3V +/-5%
■
RBIAS = 11K +/- 1 %, no load
■
62.5/10 Mhz Square Wave on TP inputs in 100/10 Mbps
LIMIT
SYM
PARAMETER
MIN
RST
RUT
TP Input Squelch
Threshold
TP Input Unsquelch
Threshold
TYP
UNIT
CONDITIONS
MAX
166
500
mV pk
100 Mbps, RLVL=0
310
540
mV pk
10 Mbps, RLVL=0
60
200
mV pk
100 Mbps, RLVL=1
186
324
mV pk
10 Mbps, RLVL=1
100
300
mV pk
100 Mbps, RLVL=0
186
324
mV pk
10 Mbps, RLVL=0
20
90
mV pk
100 Mbps, RLVL=1
112
194
mV pk
10 Mbps, RLVL=1
TP Input Open Circuit
Voltage
VDD- 2.4
± 0.2
Volt
Voltage on Either TPI+ or TPI- with
Respect to GND.
RCMR
TP Input Common
Mode Voltage Range
ROCV
± 0.25
Volt
Voltage on TPI± with Respect to
GND.
RDR
TP Input Differential
Voltage Range
RIR
TP Input Resistance
RIC
TP Input Capacitance
SMSC LAN91C111-REV B
VDD
5K
Volt
Ohm
10
pF
123
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Revision 1.8 (07-13-05)
124
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Chapter 14 Timing Diagrams
t2
Address, AEN, nBE[3:0]
Valid
nADS
t3
t4
Read Data
Valid
t6
t1
t5
nRD, nWR
t5A
Write Data
Valid
Figure 14.1 Asynchronous Cycle - nADS=0
PARAMETER
MIN
t1
A1-A15, AEN, nBE[3:0] Valid to nRD, nWR Active
2
ns
t2
A1-A15, AEN, nBE[3:0] Hold After nRD, nWR Inactive (Assuming
nADS Tied Low)
5
ns
t3
nRD Low to Valid Data
t4
nRD High to Data Invalid
2
t5
Data Setup to nWR Inactive
10
ns
t5A
Data Hold After nWR Inactive
5
ns
t6
nRD Strobe Width
15
ns
SMSC LAN91C111-REV B
125
DATASHEET
TYP
MAX
UNITS
15
ns
15
ns
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
0ns
50ns
100ns
Asynchronous Cycle -- Using nADS
150ns
200ns
250
t9
Addr,AEN,nBE[1:0]
valid
t8
nADS
t3
t4
Read Data
valid
t6
t1
t5
nRD,nWR
t5A
Write Data
valid
Figure 14.2 Asynchronous Cycle - Using nADS
PARAMETER
MIN
t1
A1-A15, AEN, nBE[3:0] Valid to nRD, nWR Active
2
t3
nRD Low to Valid Data
t4
nRD High to Data Invalid
2
t5
Data Setup to nWR Inactive
10
ns
t5A
Data Hold After nWR Inactive
5
ns
t6
nRD Strobe Width
15
ns
t8
A1-A15, AEN, nBE[3:0] Setup to nADS Rising
8
ns
t9
A1-A15, AEN, nBE[3:0] Hold after nADS Rising
5
ns
Revision 1.8 (07-13-05)
126
DATASHEET
TYP
MAX
UNITS
ns
15
ns
15
ns
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
0ns
50ns
100ns
150ns
200ns
Asynchronous Cycle - nADS=0
250n
t2
nDATACS
t3A
t4
Read Data
valid
t6A
t1A
t5
nRD,nWR
t5A
Write Data
D0~D31 valid
Figure 14.3 Asynchronous Cycle - nADS=0
PARAMETER
MIN
t1A
nDATACS Setup to nRD, nWR Active
10
ns
t2
nDATACS Hold After nRD, nWR Inactive (Assuming nADS Tied
Low)
5
ns
t3A
nRD Low to Valid Data
t4
nRD High to Data Invalid
2
t5
Data Setup to nWR Inactive
10
ns
t5A
Data Hold After nWR Inactive
5
ns
t6A
nRD Strobe Width
30
ns
Address, AEN, nBE[3:0]
Valid Address
TYP
MAX
UNITS
30
ns
15
ns
Valid Address
nRD, nWR
t26
t13
t26A
ARDY
Data
Valid
Valid Data
Figure 14.4 Asynchronous Ready
SMSC LAN91C111-REV B
127
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
PARAMETER
MIN
t26
ARDY Low Pulse Width
100
t26A
Control Active to ARDY Low
t13
Valid Data to ARDY High
t17
t12
t22
TYP
MAX
UNITS
150
ns
10
ns
10
t18
ns
t14
t18
Clock
t12A
nDATACS
t17A
W/nR
t22A
nCYCLE
t20
Write Data
a
t20
t20
b
c
t15
nRDYRTN
Figure 14.5 Burst Write Cycles - nVLBUS=1
PARAMETER
MIN
t12
nDATACS Setup to LCLK Rising
20
ns
t12A
nDATACS Hold After LCLK Rising
0
ns
t14
nRDYRTN Setup to LCLK Falling
10
ns
t15
nRDYRTN Hold after LCLK Falling
10
ns
t17
W/nR Setup to LCLK Falling
15
ns
t17A
W/nR Hold After LCLK Falling
3
ns
t18
Data Setup to LCLK Rising (Write)
15
ns
t20
Data Hold from LCLK Rising (Write)
4
ns
t22
nCYCLE Setup to LCLK Rising
5
ns
t22A
nCYCLE Hold After LCLK Rising
10
ns
Revision 1.8 (07-13-05)
128
DATASHEET
TYP
MAX
UNITS
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
t17
t12
t14
Clock
t12A
nDATACS
t17A
W/nR
nCYCLE
t19
Read Data
t19
a
b
c
t15
nRDYRTN
Figure 14.6 Burst Read Cycles - nVLBUS=1
PARAMETER
MIN
t12
nDATACS Setup to LCLK Rising
20
ns
t12A
nDATACS Hold after LCLK Rising
0
ns
t14
nRDYRTN Setup to LCLK Falling
10
ns
t15
nRDYRTN Hold after LCLK Falling
10
ns
t17
W/nR Setup to LCLK Falling
15
ns
t17A
W/nR Hold After LCLK Falling
3
ns
t19
Data Delay from LCLK Rising (Read)
5
SMSC LAN91C111-REV B
129
DATASHEET
TYP
MAX
15
UNITS
ns
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
t8
nADS
t9
Address, AEN, nBE[3:0]
Valid
t25
nLDEV
Figure 14.7 Address Latching for All Modes
PARAMETER
MIN
TYP
MAX
t8
A1-A15, AEN, nBE[3:0] Setup to nADS Rising
8
ns
t9
A1-A15, AEN, nBE[3:0] Hold After nADS Rising
5
ns
t25
A4-A15, AEN to nLDEV Delay
30
UNITS
ns
t18
t10
t20
Clock
t9
Address, AEN, nBE[3:0]
Valid
t8
nADS
t17A
t16
W/nR
t11
nCYCLE
Write Data
Valid
t21
t21
nSRDY
Figure 14.8 Synchronous Write Cycle - nVLBUS=0
Revision 1.8 (07-13-05)
130
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
PARAMETER
MIN
TYP
MAX
t8
A1-A15, AEN, nBE[3:0] Setup to nADS Rising
8
ns
t9
A1-A15, AEN, nBE[3:0] Hold After nADS Rising
5
ns
t10
nCYCLE Setup to LCLK Rising
5
ns
t11
nCYCLE Hold after LCLK Rising (Non-Burst Mode)
3
ns
t16
W/nR Setup to nCYCLE Active
0
ns
t17A
W/nR Hold after LCLK Rising with nSRDY Active
3
ns
t18
Data Setup to LCLK Rising (Write)
15
ns
t20
Data Hold from LCLK Rising (Write)
4
ns
t21
nSRDY Delay from LCLK Rising
7
UNITS
ns
t23
t20
t24
t10
Clock
t9
Address, AEN, nBE[3:0]
Valid
t8
nADS
t16
W/nR
t11
nCYCLE
Read Data
Valid
t21
t21
nSRDY
nRDYRTN
Figure 14.9 Synchronous Read Cycle - nVLBUS=0
SMSC LAN91C111-REV B
131
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
PARAMETER
MIN
TYP
MAX
t8
A1-A15, AEN, nBE[3:0] Setup to nADS Rising
8
ns
t9
A1-A15, AEN, nBE[3:0] Hold After nADS Rising
5
ns
t10
nCYCLE Setup to LCLK Rising
5
ns
t11
nCYCLE Hold after LCLK Rising (Non-Burst Mode)
3
ns
t16
W/nR Setup to nCYCLE Active
0
ns
t20
Data Hold from LCLK Rising (Read)
4
ns
t21
nSRDY Delay from LCLK Rising
t23
nRDYRTN Setup to LCLK Rising
3
ns
t24
nRDYRTN Hold after LCLK Rising
3
ns
7
UNITS
ns
t27
TXD0-TXD3
t27
TXEN100
t28
RXD0-RXD3
t28
t28
RX25
t29
RX_DV
t29
RX_ER
Figure 14.10 MII Timing
PARAMETER
MIN
t27
TXD0-TXD3, TXEN100 Delay from TX25 Rising
0
t28
RXD0-RXD3, RX_DV, RX_ER Setup to RX25 Rising
10
ns
t29
RXD0-RXD3, RX_DV, RX_ER Hold After RX25 Rising
10
ns
Revision 1.8 (07-13-05)
132
DATASHEET
TYP
MAX
UNITS
15
ns
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
AC TEST TIMING CONDITIONS
Unless otherwise noted, all test conditions are as follows:
1. VDD = 3.3V +/-5%
2. RBIAS = 11K +/- 1%, no load
3. Measurement Points:
4. TPO±, TPI±: 0.0 V During Data, ±0.3V at start/end of packet
5. All other inputs and outputs: 1.4 Volts
Table 14.1 Transmit Timing Characteristics
LIMIT
SYM
PARAMETER
MIN
t30
Transmit Propagation Delay
t31
TYP
UNIT
CONDITIONS
140
nS
100Mbps
600
nS
10Mbps
±0.7
nS pk-pk
100Mbps
±5.5
nS pk-pk
10Mbps
nS
10Mbps
10Mbps
MAX
60
Transmit Output Jitter
t32
Transmit SOI Pulse Width to
0.3V
250
t33
Transmit SOI Pulse Width to
40mV
4500
nS
t34
LEDn Delay Time
25
mS
t35
LEDn Pulse Width
105
mS
80
100Mbps
t
t 30
TPO±
FXO±
IDLE
IDLE
31
DATA
/J/K/
/T/R/
IDLE
10Mbps
t 33
t31
t30
TPO±
PREAMBLE
PREAMBLE
t34
t32
DATA
DATA
SOI
t35
LEDn
TXEN Bit is Set
Figure 14.11 Transmit Timing
SMSC LAN91C111-REV B
133
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Table 14.2 Receive Timing Characteristics
LIMIT
SYM
PARAMETER
MIN
t36
t37
TYP
Receive Input Jitter
SOI Pulse Minimum Width
Required for Idle Detection
UNIT
CONDITIONS
±3.0
nS pk-pk
100Mbps
±13.5
nS pk-pk
10Mbps
200
nS
10Mbps
Measure TPI± from last zero
cross to 0.3V point
MAX
125
t 36
TPI±
DATA
DATA DATA DATA DATA
SOI
t 37
Figure 14.12 Receive Timing, End of Packet - 10 MBPS
Table 14.3 Collision and Jam Timing Characteristics
LIMIT
SYM
PARAMETER
UNIT
CONDITIONS
200
nS
100Mbps
700
nS
10Mbps
300
nS
10Mbps
Xmt Packet Start to COL
Assert Time
200
nS
100Mbps
700
nS
10Mbps
Start of Packet to Transmit
JAM Packet Start During JAM
500
nS
100Mbps
1500
nS
10Mbps
Xmt Packet Start to COL
Assert Time
200
nS
100Mbps
700
nS
10Mbps
MIN
t38
t39
t40
t41
TYP
Rcv Packet Start to COL
Assert Time
Revision 1.8 (07-13-05)
134
DATASHEET
MAX
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
MII 100 Mbps
TPO±
I
DATA
DATA
DATA
DATA
DATA
DATA
DATA
DATA
DATA
TPI±
I
I
I
I
J
K
DATA
DATA
DATA
DATA
t
DATA
T
DATA
DATA
DATA
R
I
I
38
Collision Observed
by Physical Layer
t 34
t 35
LEDn
MII 10 Mbps
TPO±
TPI±
t
38
Collision Observed
by Physical Layer
t 34
t 35
LEDn
Figure 14.13 Collision Timing, Receive
SMSC LAN91C111-REV B
135
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
MII 100 Mbps
TPI±
I
TPO±
I
DATA DATA DATA DATA DATA DATA DATA DATA DATA DATA DATA DATA DATA
I
I
I
J
K
t
DATA DATA DATA DATA
T
R
I
I
39
Collision Observed
by Physical Layer
t 34
t 35
LEDn
MII 10 Mbps
TPI±
TPO±
t
39
Collision Observed
by Physical Layer
t 34
t 35
LEDn
Figure 14.14 Collision Timing, Transmit
Revision 1.8 (07-13-05)
136
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
MII 100 Mbps
TPO±
I
I
J
K
t
TPO±
I
I
I
DATA DATA DATA DATA DATA DATA DATA DATA DATA DATA DATA DATA
40
I
I
J
K
JAM
JAM
JAM
JAM
T
R
I
I
I
t 41
Collision Observed
by Physical Layer
MII 10 Mbps
TPI±
t
TPO±
40
JAM
JAM
JAM
JAM
Figure 14.15 Jam Timing
SMSC LAN91C111-REV B
137
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Table 14.4 Link Pulse Timing Characteristics
LIMIT
SYM
UNIT
CONDITIONS
PARAMETER
MIN
TYP
MAX
t42
NLP Transmit Link Pulse Width
See Figure 7.8
t43
NLP Transmit Link Pulse Period
8
t44
NLP Receive Link Pulse Width Required
For Detection
50
t45
NLP Receive Link Pulse Minimum Period
Required For Detection
6
7
mS
link_test_min
t46
NLP Receive Link Pulse Maximum
Period Required For Detection
50
150
mS
link_test_max
t47
NLP Receive Link Pulse Required To
Exit Link Fail State
3
3
Link
Pulses
lc_max
t48
FLP Transmit Link Pulse Width
100
150
nS
t49
FLP Transmit Clock Pulse to Data Pulse
Period
55.5
62.5
69.5
µS
t50
FLP Transmit Clock Pulse to Clock Pulse
Period
111
125
139
µS
t51
FLP Transmit Link Pulse Burst Period
8
22
mS
t52
FLP Receive Link Pulse Width Required
For Detection
50
t53
FLP Receive Link Pulse Minimum Period
Required For Clock Pulse Detection
5
25
µS
flp_test_min_timer
t54
FLP Receive Link Pulse Maximum
Period Required For Clock Pulse
Detection
165
185
µS
flp_test_max_timer
t55
FLP Receive Link Pulse Minimum Period
Required For Data Pulse Detection
15
47
µS
data_detect_min_timer
t56
FLP Receive Link Pulse Maximum
Period Required For Data Pulse
Detection
78
100
µS
data_detect_max_timer
t57
FLP Receive Link Pulse Burst Minimum
Period Required For Detection
5
7
mS
nlp_test_min_timer
t58
FLP Receive Link Pulse Burst Maximum
Period Required For Detection
50
150
mS
nlp_test_max_timer
t59
FLP Receive Link Pulses Bursts
Required To Detect AutoNegotiation
Capability
3
3
Link
Pulses
Revision 1.8 (07-13-05)
nS
24
nS
3
interval_timer
transmit_link_burst_time
r
nS
3
138
mS
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
TPO±
t 42
t 43
a.) Transmit NLP
TPI±
t 44
t 45
t 46
t 47
LEDn
b.) Receive NLP
Figure 14.16 Link Pulse Timing
SMSC LAN91C111-REV B
139
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
CLK
DATA
CLK
DATA
CLK
CLK
DATA
TPO±
t 48
t 49
t 50
t 51
a.) Transmit FLP and Transmit FLP Burst
CLK
DATA
CLK
DATA
TPI±
31.25
t 52
62.5
93.75
125
156.25
t 53
t 54
t 55
t 56
b.) Receive FLP
TPI±
t 59
t 57
t 58
LEDn
c.) Receive FLP Burst
Figure 14.17 FLP Link Pulse Timing
Revision 1.8 (07-13-05)
140
DATASHEET
SMSC LAN91C111-REV B
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Chapter 15 Package Outlines
Figure 15.1 128 Pin TQFP Package Outline, 14X14X1.0 Body
Table 15.1 128 Pin TQFP Package Parameters
A
A1
A2
D
D/2
D1
E
E/2
E1
H
L
L1
e
q
W
R1
R2
ccc
ccc
MIN
NOMINAL
MAX
REMARK
~
0.05
0.95
15.80
7.90
13.80
15.80
7.90
13.80
0.09
0.45
~
0.40 Basic
0o
0.13
0.08
0.08
~
~
~
~
1.00
16.00
8.00
14.00
16.00
8.00
14.00
~
0.60
1.00
1.20
0.15
1.05
16.20
8.10
14.20
16.20
8.10
14.20
0.20
0.75
~
~
0.18
~
~
~
~
7o
0.23
~
0.20
0.0762
0.08
Overall Package Height
Standoff
Body Thickness
X Span
1/ X Span Measure from Centerline
2
X body Size
Y Span
1/ Y Span Measure from Centerline
2
Y body Size
Lead Frame Thickness
Lead Foot Length from Centerline
Lead Length
Lead Pitch
Lead Foot Angle
Lead Width
Lead Shoulder Radius
Lead Foot Radius
Coplanarity (Assemblers)
Coplanarity (Test House)
Notes:
1. Controlling Unit: millimeter
2. Tolerance on the position of the leads is ± 0.035 mm maximum
3. Package body dimensions D1 and E1 do not include the mold protrusion.
Maximum mold protrusion is 0.25 mm
4. Dimension for foot length L measured at the gauge plane 0.25 mm above the seating plane is 0.78-1.08 mm.
5. Details of pin 1 identifier are optional but must be located within the zone indicated.
6. Shoulder widths must conform to JEDEC MS-026 dimension 'S' of a minimum of 0.20mm.
SMSC LAN91C111-REV B
141
DATASHEET
Revision 1.8 (07-13-05)
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Figure 15.2 128 Pin QFP Package Outline, 3.9 MM Footprint
Table 15.2 128 Pin QFP Package Parameters
A
A1
A2
D
D/2
D1
E
E/2
E1
H
L
L1
e
q
W
R1
R2
ccc
ccc
MIN
NOMINAL
MAX
REMARKS
~
0.05
2.55
23.70
11.85
19.90
17.70
8.85
13.90
~
0.73
~
0.5 Basic
0o
0.10
0.13
0.13
~
~
~
~
~
23.90
11.95
20.0
17.90
8.95
14.00
~
0.88
1.95
3.4
0.5
3.05
24.10
12.05
20.10
18.10
9.05
14.10
~
1.03
~
~
~
~
~
~
~
7o
0.30
~
0.30
0.0762
0.08
Overall Package Height
Standoff
Body Thickness
X Span
1/ X Span Measured from Centerline
2
X body Size
Y Span
1/ Y Span Measured from Centerline
2
Y body Size
Lead Frame Thickness
Lead Foot Length
Lead Length
Lead Pitch
Lead Foot Angle
Lead Width
Lead Shoulder Radius
Lead Foot Radius
Coplanarity (Assemblers)
Coplanarity (Test House)
Notes:
1. Controlling Unit: millimeter
2. Tolerance on the position of the leads is + 0.04 mm maximum.
3. Package body dimensions D1 and E1 do not include the mold protrusion.
Maximum mold protrusion is 0.25 mm.
4. Dimension for foot length L measured at the gauge plane 0.25 mm above the seating plane.
5. Details of pin 1 identifier are optional but must be located within the zone indicated.
Revision 1.8 (07-13-05)
142
DATASHEET
SMSC LAN91C111-REV B