NKK LB16SKW01-05-BJ

Toggles
Series LB
Rockers
General Specifications
Electrical Capacity (Resistive Load)
Slides
Rotaries
Keylocks
Programmable Illuminated PB
Pushbuttons
Power Level (silver):
Logic Level (gold): Other Ratings
D
Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Contact Timing: Travel: Materials & Finishes
Housing:
Snap-in Frame:
Movable Contact:
Stationary Contacts:
Base:
Switch Terminals:
Lamp Terminals:
Operating Temperature Range: Humidity: Vibration: Shock: Sealing: Touch
Standards & Certifications
Accessories
3A @ 125V AC or 3A @ 250V AC or 3A @ 30V DC
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
50 milliohms maximum for silver; 100 milliohms maximum for gold
200 megohms minimum @ 500V DC
1,000V AC minimum between contacts for 1 minute minimum;
1,500V AC minimum between contacts & case for 1 minute minimum
1,000,000 operations minimum for momentary circuit
200,000 operations minimum for maintained circuit
100,000 operations minimum
4.41N
Nonshorting (break-before-make)
Pretravel .059” (1.5mm); Overtravel .059” (1.5mm); Total Travel .118” (3.0mm)
Glass fiber reinforced polyamide (UL94V-0)
Stainless steel
Silver alloy or copper with gold plating
Silver alloy or copper with gold plating
Liquid crystal polymer (UL94V-0)
Phosphor bronze with silver or gold plating
Brass with silver plating
–25°C through +50°C (–13°F through +122°F) for Illuminated
–25°C through +70°C (–13°F through +158°F) for Nonilluminated
Note: When used with a polyvinyl chloride splash cover, the lowest limit is 0°C (32°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Not available for snap-in; see next section for panel seal.
Installation
Indicators
Tilt
Tactiles
Environmental Data
Supplement
Standard Size Pushbuttons
Cap Installation Force: 3.92N maximum downward force on cap
Quick Connect Force: 52.95N maximum downward force on connector
Soldering Time & Temperature: Manual Soldering: See Profile A in Supplement section.
Flammability Standards:
UL:
CSA:
D46
UL94V-0 housing & base
File No. E44145
All models recognized at 3A @ 125V or 250V AC or 0.4VA @ 28V AC/DC maximum.
Add “/U” to end of part number to order UL mark on switch.
Add “/CUL” to end of part number to order cULus mark on switch.
File Nos. 023535_0_000
All models certified at 3A @ 125V or 250V AC or 0.4VA @ 28V AC/DC maximum.
Add “/C” to end of part number to order CSA mark on switch.
www.nkk.com
Toggles
Series LB
Standard Size Pushbuttons
Rockers
Distinctive Characteristics
Spot illumination available in single and bicolor LEDs.
Choice of super bright LEDs in white, green, and blue
in addition to standard or bright red, amber, and
green LEDs.
D
Stainless steel clips provide secure mounting with a
wide range of panel thicknesses.
Keylocks
Latchdown feature gives indication of circuit status.
Audible and tactile feedback with smooth and
responsive operation.
Programmable Illuminated PB
Pushbuttons
Carefully designed light diffusion and filtering system produces bright,
full surface illumination with front panel relamping.
Rotaries
Snap-action contact mechanism gives long electrical
life and sensitivity of actuation.
Combination solder lug and .110” quick connect
terminals are epoxy sealed to prevent entry of flux,
dust, and other contaminants.
Slides
Panel sealed model meets IP65 of IEC60529 specifications
(similar to NEMA 4 & 13).
Tactiles
Compact switch design minimizes behind panel depth.
Actual Size
Page D46
Panel Seal
Page D57
www.nkk.com
D47
Supplement
Accessories
Snap-in Mount
Indicators
Touch
Tilt
Matching indicators available.
Series LB
Poles
D
5
S
Circuits
1
SPDT
2
DPDT
5
ON
Shapes
(ON)
( ) = Momentary
6
ON
K
ON
W01
Housing
5C12
JC
Rockers
1
Lamps
Cap Types & Colors
Incandescent Lamp Used with Solid Cap
Solid Cap: Lens/Filter Colors
S
Square
K
Black
05
5-volt
BJ
White/Clear
C
Round
G
Gray
12
12-volt
CJ
Red/Clear
R
Rectangular
EJ
Yellow/Clear
FJ
Green/Clear
GJ
Blue/Clear
No
Code
Alternate Action
with Latchdown
Nonilluminated
Pushbuttons
Pushbuttons
Rockers
LB
D
Contacts & Terminals
G01
Gold Contacts
Rated 0.4VA @ 28V AC/DC
Solder Lug/Quick Connect Terminals*
Switches are supplied
without UL, cULus, & CSA
markings unless specified.
Specific models & ratings noted
on General Specifications page.
01
110-volt Neon
JB
Clear/White
05
5-volt Incandescent
JC
Clear/Red
12
12-volt Incandescent
No
Code
Nonilluminated
*JG
Clear/Blue
Red, 12-volt, Bright LED
with Resistor
SPDT ON-(ON) Circuit
Silver Contacts
Rated 3A @ 125/250V AC;
Solder Lug/Quick Connect Terminals
Black Housing
Amber
5F
Green
Supplement
Clear/White
No Resistor
JC
Clear/Red
05
5-volt
JD
Clear/Amber
12
12-volt
JF
Clear/Green
24
24-volt
Super Bright LED Used with LED Cap
6B
White
6F
Green
6G
Blue
LED Cap: Lens/Diffuser Colors
JB
LED in Spot Illuminated Cap
Clear/White
Spot Illuminated Cap Colors
1C
Red Single Color
A
Black
1D
Amber Single Color
B
White
1F
Green Single Color
C
Red
CF
Red/Green Bicolor
F
Green
Nonilluminated
Nonilluminated
Slides
JB
Tilt
5D
No
Code
www.nkk.com
No Code
Red
Clear Cap with Red Diffuser
Square Shape
Resistor
LED Cap: Lens/Diffuser Colors
Tactiles
Bright LED Used with LED Cap
Touch
Tilt
LB15SKW01-5C12-JC
Touch
Clear/Green
Available in
Square and
Round only.
Indicators
Slides
Tactiles
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
Indicators
Clear/Yellow
Accessories
* Wire harness & cable assemblies offered only in Americas
5C
Accessories
JE
*JF
*JF & JG not suitable with neon.
Colors
D48
Insert Cap: Lens/Filter Colors
Nonilluminated Cap Colors
A
Black
F
Green
B
White
G
Blue
C
Red
H
Gray
E
Yellow
www.nkk.com
Supplement
Rotaries
IMPORTANT:
Incandescent or Neon Used with Insert Cap
Keylocks
W01
Silver Contacts
Rated 3A @ 125/250V AC
Solder Lug/Quick Connect Terminals*
Rotaries
Keylocks
Programmable Illuminated PB
Toggles
TYPICAL SWITCH ORDERING EXAMPLE
Programmable Illuminated PB
Toggles
Standard Size Snap-in Pushbuttons
D49
Series LB
Toggles
Standard Size Snap-in Pushbuttons
POLES & CIRCUITS
Rockers
Plunger Position
( ) = Momentary
Model
Normal
Down
Normal
Down
Throw & Switch/Lamp Schematics
Notes: Switch is marked with NC, NO, COM, L+, L–.
Lamp circuit is isolated and requires an
external power source.
SP
LB15
*LB16
ON
ON
(ON)
ON
1-3
1-2
SPDT
DP
LB25
*LB26
ON
ON
(ON)
ON
1-3 4-6
1-2 4-5
DPDT
D
S
.622” (15.8mm)
Square
.854” (21.7mm)
Round
C
Rotaries
NC
2
COM
NC 2
NO
6
L (+)
(-) L
L (+)
(-) L
NO
4
COM
NC
5
NO
R
(22.0) Dia
.866
.622” x .866” (15.8mm x 22.0mm)
Rectangular
(16.2)
.638
(11.5)
.453
(16.2) Sq
.638
(22.4)
.882
(1.5) R
.059
Cutout for 1 switch:
.638” x .638” (16.2mm x 16.2mm)
Cutout for 1 switch with barriers:
.638” x .815” (16.2mm x 20.7mm)
Cutout for 1 switch:
.638” x .882” (16.2mm x 22.4mm)
Cutout for 1 switch with barriers:
.638” x 1.059” (16.2mm x 26.9mm)
Panel Thickness for Switches & Barriers: .039” ~ .157” (1.0 ~ 4.0mm)
Panel Thickness for Protective Guards & Splash Covers: .039” ~ .138” (1.0 ~ 3.5mm)
HOUSING
Tactiles
Slides
COM
SHAPES & PANEL CUTOUTS
K
G
Black
Gray
Tilt
CONTACT MATERIALS, RATINGS & TERMINALS
Touch
W01
Indicators
3
1
* When in latchdown position for the alternate circuit, cap position is .039” (1.0mm) above the built-in bezel.
Housing Colors Available:
G01
Solder Lug/Quick Connect
Silver Contacts
Power Level
3A @ 125V AC & 250V AC
Gold Contacts
Logic Level
0.4VA max. @ 28V AC/DC max.
Epoxy
Seal
Optional PCB adaptors
(2.0)
AT711 & AT712 available;
.079
illustrated in “Optional
Accessories” immediately following
“Typical Switch Dimensions.”
Complete explanation of operating range in Supplement section.
(7.5)
.295
(2.8)
.110
(1.2)
.047
Thk = (0.5)
.020
INCANDESCENT & NEON LAMP CODES & SPECIFICATIONS
AT607 & AT607N
Supplement
Accessories
3
1
Keylocks
Programmable Illuminated PB
Pushbuttons
Pole
Connected Terminals
AT607 Incandescent 5-volt or
12-volt; AT607N Neon 110-volt
D50
12
01 *
Voltage
V
5V AC
12V AC
110V AC
Current
I
115mA
60mA
1.5mA
Endurance
T-1 Bi-pin
05
Avg. Hours
Ambient Temp. Range
10,000
–25°C ~ +50°C
www.nkk.com
10,000
The electrical specifications shown are
determined at a basic temperature of
25°C. Lamp circuit is isolated and
requires external power source.
* Recommended Resistors for Neon:
33K ohms for 110V AC;
100K ohms for 220V AC
Series LB
Toggles
Standard Size Snap-in Pushbuttons
LED COLORS & SPECIFICATIONS
Rockers
The electrical specifications shown are determined at a basic temperature of 25°C.
LED circuit is isolated and requires external power source. Polarity marks are on the switch.
If the source voltage exceeds the rated voltage, a ballast resistor is required.
The resistor value can be calculated by using the formula in the Supplement section.
Additional lamp detail is shown in the Accessories & Hardware section.
(+)
(-)
Green
5C
5D
5F
No Code
Red
Amber
Green
Forward Peak Current
IFM
30mA
30mA
30mA
Continuous Forward Current
IF
20mA
20mA
20mA
Forward Voltage
VF
1.9V
2.0V
2.1V
Reverse Peak Voltage
VRM
5V
5V
5V
Current Reduction Rate Above 25°C
∆IF
D
0.42mA/°C
Ambient Temperature Range
T-1 ⁄ Bi-pin
12
No Resistor
–25° ~ +50°C
Keylocks
LEDs are colored
in OFF state.
Amber
Bright LED with Resistor
Green
5C
5D
5F
Resistor Codes
05
12
24
Forward Peak Current
IFM
—
—
—
Continuous Forward Current
IF
52mA
26mA
13mA
Forward Voltage
VF
5V
12V
24V
Reverse Peak Voltage
VRM
4V
8V
16V
Current Reduction Rate Above 25°C
∆IF
0.50mA/°C
Ambient Temperature Range
T-1 Bi-pin
AT627
5-volt
4-element (+)
with Resistor
(-)
AT627
12-volt
4-element
with Resistor
Rotaries
Amber
Slides
Color Codes:
Red
–25° ~ +50°C
(+)
(-)
Tactiles
AT627
with Resistor
Programmable Illuminated PB
Color Codes
Red
AT627
24-volt
(+)
4-element
with Resistor
(-)
Tilt
AT635
Pushbuttons
Bright LED without Resistor
6F
6G
Color
White
Green
Blue
Forward Peak Current
IFM
30mA
30mA
30mA
Continuous Forward Current
IF
20mA
20mA
20mA
Forward Voltage
VF
3.6V
3.5V
3.6V
Reverse Peak Voltage
VRM
(-)
5V
5V
5V
Current Reduction Rate Above 25°C
∆IF
T-1 Bi-pin
Ambient Temperature Range
0.50mA/°C
–25° ~ +50°C
Supplement
(+)
No Code
6B
Indicators
ATTENTION
ELECTROSTATIC
SENSITIVE DEVICES
Accessories
AT625G Blue
AT631B White
AT632F Green
Touch
Super Bright Single Element LED
No Lamp
www.nkk.com
D51
Series LB
Toggles
Standard Size Snap-in Pushbuttons
CAP TYPES & COLOR COMBINATIONS
Color Codes:
Rockers
Pushbuttons
Lens/Filter
Colors Available:
D
D Amber
E Yellow
F Green
G Blue
J Clear
BJ
FJ
CJ
GJ
AT4012
Round
AT476
Square
(3.5)
.138
(13.2) Sq
.520
(19.0) Dia
.748
AT4026
Rectangular
(4.5)
.177
(5.5)
.217
(13.2)
.520
Translucent Colored Lens
(19.4)
.764
(5.0)
.197
(6.0)
.236
(6.5)
.256
Transparent Clear Filter
EJ
Material: Polycarbonate
Lamp AT607
Finish: Glossy
Insert Cap for Incandescent or Neon Lamp & Nonilluminated
Lens/Filter
Colors Available:
Keylocks
Programmable Illuminated PB
C Red
Solid Cap for Incandescent Lamp & Nonilluminated
Rotaries
Slides
Tactiles
B White
JB
JF
JC
JG
AT477
Square
AT4013
Round
(3.5)
.138
(13.2) Sq
.520
(19.0) Dia
.748
AT4027
Rectangular
(4.5)
.177
(5.5)
.217
(13.2)
.520
Transparent Clear Lens
(19.4)
.764
(5.0)
.197
(6.0)
.236
(6.5)
.256
Translucent Colored Filter
JE
JF and JG not suitable
with neon lamp.
Material: Polycarbonate
Finish: Glossy
Lamp AT607 or 607N
Cap for Bright LED without Resistor
Lens/Diffuser
Colors Available:
JB
(13.2) Sq
.520
Tilt
JC
AT4176
Square
AT4178
Round
(19.0) Dia
.748
(3.5)
.138
(4.5)
.177
(13.2)
.520
Transparent Clear Lens
(19.4)
.764
(6.5)
.256
(5.0)
.197
(5.5)
.217
JD
JF
Touch
AT4177
Rectangular
Material: Polycarbonate
(6.0)
.236
Translucent Colored Diffuser
Bright LED
AT635
Finish: Glossy
Lens/Diffuser
Colors Available:
JB
Accessories
Indicators
Cap for Bright LED with Resistor
JC
Supplement
JD
AT4162
Square
AT4164
Round
AT4163
Rectangular
Transparent Clear Lens
(13.2) Sq
.520
(3.5)
.138
(6.5)
.256
(19.0) Dia
.748
(4.5)
.177
(13.2)
.520
(5.0)
.197
(6.0)
.236
(5.5)
.217
JF
Material: Polycarbonate
D52
www.nkk.com
(19.4)
.764
Finish: Glossy
Translucent Colored Diffuser
Bright LED
AT627
Series LB
Toggles
Standard Size Snap-in Pushbuttons
CAP TYPES & COLOR COMBINATIONS
E Yellow
F Green
G Blue
H Gray
J Clear
(3.5)
.138
(13.2) Sq
.520
Material:
Polycarbonate
Finish: Glossy
AT4128
Round
AT4129
Square
(19.0) Dia
.748
Transparent
Clear Lens
AT4130
Rectangular
(13.2)
.520
(4.5)
.177
(5.5)
.217
(19.4)
.764
Translucent
White Diffuser
(5.0)
.197
(6.0)
.236
(6.5)
.256
LEDs AT625
AT631 AT632
Spot Illuminated Cap with LED
The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires an external
power source. Single color LEDs are colored in OFF state; bicolor LEDs are translucent white in OFF state. Polarity marks are on the
switch. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the
formula in the Supplement section. Additional lamp detail is shown in the Accessories & Hardware section.
(+)
(-)
1C
1D
1F
CF
Red
Amber
Green
Red/Green
Forward Peak Current
IFM
10mA
30mA
30mA
30/25mA
Continuous Forward Current
IF
8mA
24mA
24mA
20mA
Forward Voltage
VF
1.9V
2.0V
2.1V
2.0/2.2V
Reverse Peak Voltage
VRM
5V
5V
5V
—
Current Reduction Rate Above 25°C
∆IF
0.40mA/°C
0.43/0.38mA/°C
0.13mA/°C 0.40mA/°C
Ambient Temperature Range
Cap Colors
Available:
A
C
B
F
(13.2) Sq
.520
(4.0)
.157 (2.0)
.079
(5.0)
.197
–25° ~ +50°C
AT480
Square
AT4016
Round
(19.0) Dia
.748
(3.5)
.138
(6.5)
.256
Material:
Polycarbonate
Finish: Glossy
Slides
Not Available
Separately
(+)
(-)
Bicolor
Tactiles
LED factory
assembled in Spot
Illuminated Caps
Single Color
Bicolor LED
with 2 Elements
(5.0)
.197
(4.5)
.177
(5.5)
.217
Cap with Window
(2.0)
(6.0) .079
.236
Factory Assembled LED;
Not Available Separately
Cap for Nonilluminated
E
B
F
C
G
AT484
Square
H
(13.2) Sq
.520
AT4017
Round
(3.5)
.138
(19.0) Dia
.748
(6.5)
.256
Material: Polycarbonate
(4.5)
.177
(5.5)
.217
AT4030
Rectangular
(13.2)
.520
Accessories
A
Indicators
When ordering spot illuminated cap separately, LED color must be specified.
Examples: AT480CA (red LED, black cap); AT4016CFB (red/green bicolored LED, white cap)
Cap Colors
Available:
(19.4)
.764
(5.0)
.197
(6.0)
.236
Cap
No Lamp
Finish: Glossy
www.nkk.com
D
Keylocks
LED Specifications
Single Color LED
with 1 Element
Pushbuttons
JB
Rockers
Cap for Super Bright LEDs
Clear Lens
White Diffuser
Programmable Illuminated PB
D Amber
Rotaries
C Red
Tilt
B White
Touch
A Black
D53
Supplement
Color Codes:
Series LB
Toggles
Standard Size Snap-in Pushbuttons
TYPICAL SWITCH DIMENSIONS
Square
Single & Double Pole
Rockers
(0.5) Typ
.020
Pushbuttons
3
NO
L (+)
D
(21.5)
.846
(3.2)
.126
(15.8) Sq
.622
5
1
4
L (-)
(1.0)
.039
(17.8) Sq
.701
6
2
COM
(2.54) Typ
.100
(2.8) Typ
.110
(5.08) Typ
.200
(7.5)
.295
Latchdown Position
LB15SKW01-12-CJ
Single pole models do not have terminals 4, 5, & 6. Round
Single & Double Pole
(1.2) x (2.0) Typ
.047 x .079
(1.8)
.071
(0.5) Typ
.020
NC
3
NO
COM
(2.54) Typ
.100
(1.0)
.039
Rotaries
(19.0) Dia
.748
(23.7) Dia
.933
(3.2)
.126
L (+)
6
2
5
1
4
L (-)
(15.8) Sq
.622
(21.7) Dia
.854
(2.8) Typ
.110
(5.08) Typ
.200
(7.5)
.295
(21.5)
.846
Latchdown Position
LB16CKW01-12-CJ
Slides
NC
(13.2) Sq
.520
Keylocks
Programmable Illuminated PB
(1.2) x (2.0) Typ
.047 x .079
(1.8)
.071
Single pole models do not have terminals 4, 5, & 6. Rectangular
Single & Double Pole
Tactiles
(1.8)
.071
(1.2) x (2.0) Typ
.047 x .079
(0.5) Typ
.020
(13.2)
.520
(17.8)
.701
NC
NO
COM
Tilt
(2.54) Typ
.100
(19.4)
.764
(3.2)
.126
Touch
LB26RGW01-12-CJ
6
5
2
(15.8)
.622
4
1
(5.08) Typ
.200
(22.0)
.866
(7.5)
.295
(22.5)
.886
Latchdown Position
L (+)
L (-)
(1.0)
.039
(24.0)
.945
3
(2.8) Typ
.110
Single pole models do not have terminals 4, 5, & 6. Indicators
OPTIONAL ACCESSORIES
PCB Adaptors
AT711
Single Pole • Straight PC Terminals
Accessories
(0.3) Typ
.012
NC
NO
COM
Supplement
(0.5)
.020
(15.0)
(4.0)
.591
.157
L
(+)
(-)
NO
COM
(2.54) Typ
.100
(0.74) Typ
.029
(5.08)
.200
Double Pole • Straight PC Terminals
(0.3) Typ
.012
(5.08)
.200
NC
L
AT712
(15.8) Sq
.622
NO
(2.54) Typ
.100
(1.0) Dia Typ
.039
COM
(0.5)
.020
(15.0)
(4.0)
.591
.157
Note: Order adaptors separately.
D54
www.nkk.com
(2.54) Typ
.100
(0.74) Typ
.029
(5.08) Typ
.200
NC
NC
L
(+)
NO
L
(-)
COM
(15.8) Sq
.622
(2.54) Typ
.100
(1.0) Dia Typ
.039
(5.08)
.200
Series LB
Toggles
Standard Size Snap-in Pushbuttons
OPTIONAL ACCESSORIES
(23.5)
.925
(4.3) Typ
.169
(5.2)
.205
(20.0)
.787
A
Pushbuttons
End Position
Cutouts for More Than 1 Switch
(19.2)
.756
(16.2)
.638
(15.0)
.591
Center Position
Material: Polyamide
(1.19)
.047
(1.19)
.047
Square
A = .752” (19.1mm) x Number of Switches + .051” (1.3mm)
Rectangular
A = .996” (25.3mm) x Number of Switches + .051” (1.3mm)
(19.2)
.756
AT499
Square
Protective Guard
Keylocks
Protective Guard
D
Programmable Illuminated PB
AT498
Center
AT497
End
Rockers
Barriers
(10.0)
.394
Material: Polyamide
Cap Height
When
Assembled
(20.0)
.787
(14.0) Sq
.551
(17.9) Sq
.705
(8.0)
.315
Slides
(17.0)
.669
Rotaries
(21.0)
.827
Opens 90°
Closes manually
Protective Guards reduce depth of switch behind panel by .020” (0.5mm).
Tactiles
Spring Loaded Protective Guard
(10.5)
.413
(17.9)
.705
(20.5)
.807
(7.1)
.280
(18.4)
.724
(20.4)
.803
Cap Height
When
Assembled
(7.5)
.295
(14.2)
.559
(17.9)
.705
(16.2) Sq
.638
(20.5)
.807
180°
Accessories
Materials:
Cover: Clear Polycarbonate
Base: Black GFR Polyamide
Coil Spring: Stainless Steel
(10.5)
.413
Indicators
(39.0) Min*
1.535
AT4171
(20.4)
.803 (N)
* Minimum dimension allows opening of cover to 180°
Supplement
(20.4)
.803
(N) = Number of switches
Recommended Panel Thickness:
.039” ~ .106” (1.0mm ~ 2.7mm)
www.nkk.com
Tilt
Opens 180°
Closes automatically
Touch
AT4171
Square
Protective Guard
D55
Series LB
Toggles
Standard Size Snap-in Pushbuttons
OPTIONAL ACCESSORIES
Protective Guard
Rockers
AT4057
Rectangular
Protective Guard
Pushbuttons
Opens 90°
Closes manually
Cap Height
When
Assembled
D
Material: Polyamide
(24.15)
.951
(8.0)
.315
Protective Guards reduce depth of switch behind panel by .020” (0.5mm).
Spring Loaded Protective Guard
AT4172
Rectangular
Protective Guard
(10.5)
.413
(7.1)
.280
(24.6)
.969
Rotaries
(16.2)
.638
(39.0) Min*
1.535
Cap Height
When
Assembled
(26.6)
1.047
(20.4)
.803
(7.5)
.295
180°
Materials:
Cover: Clear Polycarbonate
Base: Black GFR Polyamide
Coil Spring: Stainless Steel
(20.5)
.807
(26.6)
1.047
(26.6)
1.047 (N)
(N) = Number of switches
(24.1)
.949
Opens 180°
Closes automatically
(10.5)
.413
Tactiles
(17.9)
.705
(20.5)
.807
(22.4)
.882
AT4172
Slides
(14.0)
.551
(21.0)
.827
(26.0)
1.024
Keylocks
Programmable Illuminated PB
(10.0)
.394
Recommended Panel Thickness:
.039” ~ .106” (1.0mm ~ 2.7mm)
* Minimum dimension allows opening of cover to 180°
Tilt
Dust Covers
AT4001
Square
AT4011
Rectangular
Indicators
Touch
AT4002
Round
Supplement
Accessories
(21.0) Dia
.827
(15.0) Sq
.591
Cap Height
When
Assembled
Cap Height
When
Assembled
(7.3)
.287
(2.5)
.098
(21.8) Dia
.858
(30.0) Dia
1.181
(16.5)
.650
(16.5)
.650
(22.7)
.894
(2.5)
.098
(7.3)
.287
(24.0)
.945
(24.0) Sq
.945
(30.2)
1.189
Materials: PVC with polyethylene gasket; PVC loses pliability below 0°C (32°F). Dust Covers reduce depth of switch behind panel by .020” (0.5mm).
D56
www.nkk.com