MPD LF100EDI Low cost, dual output high isolation 1w smt dc/dc converter Datasheet

LF100EDI Series
Low Cost, Dual Output
High Isolation 1W SMT
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
Input
• 1W Output Power
Parameter
• 3,000 VDC Isolation
• Ultra-Miniature SMT Case
Conditions
3.3 VDC Input
Input Voltage Range
• UL Approved (File E245422)
Reverse Polarity Input Current
• Dual Outputs
Input Filter
• Low 0.24” Profile
Output
• >3.5 MHour MTBF
Parameter
• 3.3, 5V, & 12V Inputs
Output Voltage Accuracy
• LOWEST COST!
Output Voltage Balance
Line Regulation
Load Regulation (Note 1)
Min.
Typ.
Max.
3.0
3.3
3.6
5 VDC Input
4.5
5.0
5.5
12 VDC Input
10.8
12.0
13.2
Units
VDC
1.0
A
Max.
Units
Capacitor
Conditions
Min.
Typ.
Balanced Loads
±3.0
%
±1.0
%
For Vin Change of 1%
±1.2
%
50
75
mV P - P
±0.01
±0.02
%/ºC
Max.
Units
See Model Selection Guide
Ripple & Noise (20 MHz) (Note 2)
Temperature Coefficient
Output Short Circuit
Momentary (0.5 Sec.)
General
Parameter
Conditions
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Min.
60 Seconds
3,000
500 VDC
1,000
100 kHz, 1V
Switching Frequency
Typ.
VDC
MΩ
70
pF
100
150
200
kHz
Min.
Typ.
Max.
Units
-40
+25
+85
ºC
+125
ºC
95
%
Environmental
Parameter
Conditions
Operating Temperature Range
Ambient
Storage Temperature Range
-55
Cooling
Humidity
Free Air Convection
RH, Non-condensing
Physical
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T: (781) 344-8226
F: (781) 344-8481
E: [email protected]
W: www.micropowerdirect.com
Case Size
0.60 x 0.29 x 0.24 Inches (15.24 x 7.5 x 6.0 mm)
Case Material
Non-Conductive Black Plastic (UL94-V0)
Weight
0.05 Oz (1.5g)
Reliability Specifications
Parameter
MTBF
Conditions
Min.
MIL HDBK 217F, 25ºC, Gnd Benign
Typ.
Max.
3.5
Units
MHours
Safety Standards
UL 1950, EN 60950, IEC 60950
Safety Approvals
UL, cUL; File No. E245422
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Lead Temperature
Internal Power Dissipation
Conditions
Min.
Typ.
Max.
3.3 VDC Input
-0.7
5 VDC Input
-0.7
7.0
12 VDC Input
-0.7
15.0
1.5 mm From Case For 10 Sec
All Models
Units
7.0
VDC
260.0
ºC
450
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
Model Selection Guide
Model
Number
LF101EDI
LF102EDI
LF103EDI
LF104EDI
LF111EDI
LF112EDI
LF113EDI
LF114EDI
LF151EDI
LF152EDI
LF153EDI
Input
Voltage (VDC)
Current (mA)
Voltage
Nominal
Range
Full-Load No-Load (VDC)
5
4.5 - 5.5
294
30
±5.0
5
4.5 - 5.5
277
30
±9.0
5
4.5 - 5.5
270
30
±12.0
5
4.5 - 5.5
270
30
±15.0
12
10.8 - 13.2
121
15
±5.0
12
10.8 - 13.2
116
15
±9.0
12
10.8 - 13.2
113
15
±12.0
12
10.8 - 13.2
113
15
±15.0
3.3
3.0 - 3.6
452
55
±5.0
3.3
3.0 - 3.6
445
55
±12.0
3.3
3.0 - 3.6
432
55
±15.0
Output
Current
(mA, Max)
±100.0
±56.0
±42.0
±33.0
±100.0
±56.0
±42.0
±33.0
±100.0
±42.0
±33.0
Notes:
1. Output load regulation is specified for a load change of 10% to 100%.
2. When measuring output ripple, it is recommended that an external 0.33 µF ceramic
capacitor be placed from the +Vout pin to the -Vout pin for single output units and from
each output to common for dual output units.
3. During operation, care must be taken not to exceed the specified input range of the unit
or to allow the output load to drop below the specified minimum (10% of full load).
Operating the unit under either of these conditions could cause damage to the unit.
4. These converters are specified for operation without external components. However,
in some applications the addition of input/output capacitors will enhance stability and
reduce output ripple. Recommended capacitor values are:
Vin
Input
Capacitor
3.3 VDC
5 VDC
12 VDC
10.0 µF
4.7 µF
2.2 µF
Vout
Output
Capacitor
5 VDC
9 VDC
12 VDC
15 VDC
4.7 µF
2.2 µF
1.0 µF
0.47 µF
Current
(mA, Min)
±10.0
±6.0
±5.0
±4.0
±10.0
±6.0
±5.0
±4.0
±10.0
±5.0
±4.0
Load
Regulation
(%, Max)
12.0
8.0
8.5
7.0
12.0
8.0
8.5
7.0
12.0
8.5
7.0
Efficiency
(%, Typ)
68
72
74
74
69
72
74
75
67
68
70
Fuse Rating
Slow-Blow
(mA)
500
500
500
500
200
200
200
200
750
750
750
Derating Curve
For applications requiring very low output noise levels, a simple LC filter
should be effective.
5. It is recommended that a fuse be used on the
input of a power supply for protection. See
Pin Description
Pin Description
the Model Selection table above for the correct
1
-Vin
7
NC
rating.
2
+Vin
8
+Vout
3
NC
10
NC
5
Common
11
NC
6
-Vout
12
NC
NC = No Connection
Recommended Solder Profile
Pin Connections
Mechanical Dimensions
Board Layout
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
• Pin 1 is marked by a “dot” or indentation on the unit
MicroPower Direct
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: [email protected]
Similar pages