MPD LF112ES Lowest cost, single output 1w ultra-miniature smt dc/dc converter Datasheet

LF100ES Series
Lowest Cost, Single Output
1W Ultra-Miniature SMT
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
Input
• 1W Output Power
• Ultra-Miniature SMT Case
• UL Approved (File E245422)
• Single Output
• Low 0.246” Profile
• 1,000 VDC Isolation
• >3.5 MHour MTBF
• 3.3V, 5V, & 12V Inputs
• LOWEST COST!
Parameter
Conditions
3.3 VDC Input
Input Voltage Range
Min.
Typ.
Max.
3.0
3.3
3.6
5 VDC Input
4.5
5.0
5.5
12 VDC Input
10.8
12.0
13.2
Reverse Polarity Input Current
Input Filter
Units
VDC
1.0
A
Max.
Units
Capacitor
Output
Parameter
Conditions
Min.
Output Voltage Accuracy
Typ.
±3.0
%
Line Regulation, 3.3V Output
For Vin Change of 1%
±1.5
%
Line Regulation, All Other Outputs
For Vin Change of 1%
±1.2
%
Load Regulation
See Model Selection Guide
Ripple & Noise (20 MHz)
50
Temperature Coefficient
Output Short Circuit
100
mV P - P
±0.03
%/ºC
Max.
Units
Momentary (0.5 Sec.)
General
Parameter
Conditions
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Min.
60 Seconds
1,000
500 VDC
1,000
100 kHz, 1V
Switching Frequency
Typ.
VDC
MΩ
70
pF
100
kHz
Environmental
Parameter
Conditions
Operating Temperature Range
Ambient
Storage Temperature Range
Typ.
Max.
-40
+25
+85
ºC
+125
ºC
95
%
-55
Cooling
Humidity
Min.
Units
Free Air Convection
RH, Non-condensing
Physical
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Case Size
0.50 x 0.29 x 0.24 Inches (12.7 x 7.5 x 6.0 mm)
Case Material
Non-Conductive Black Plastic (UL94-V0)
Weight
0.05 Oz (1.5g)
Reliability Specifications
Parameter
T: (781) 344-8226
MTBF
F: (781) 344-8481
Safety Standards
E: [email protected]
W: www.micropowerdirect.com Safety Approvals
Conditions
Min.
MIL HDBK 217F, 25ºC, Gnd Benign
3.5
Typ.
Max.
Units
MHours
UL 1950, EN 60950, IEC 60950
UL, cUL; File No. E245422
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Lead Temperature
Internal Power Dissipation
Conditions
Min.
Typ.
Max.
3.3 VDC Input
-0.7
5 VDC Input
-0.7
7.0
12 VDC Input
-0.7
15.0
1.5 mm From Case For 10 Sec
All Models
Units
7.0
VDC
260.0
ºC
450
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
Model Selection Guide
Model
Number
LF101ES
LF102ES
LF103ES
LF104ES
LF109ES
LF111ES
LF112ES
LF113ES
LF114ES
LF151ES
LF152ES
LF153ES
LF159ES
Input
Output
Load
Voltage (VDC)
Current (mA)
Voltage Current
Current Regulation
Nominal
Range
Full-Load No-Load (VDC) (mA, Max) (mA, Min) (%, Max)
5
4.5 - 5.5
260
30
5.0
200.0
20.0
15.0
5
4.5 - 5.5
263
30
9.0
111.0
23.0
9.0
5
4.5 - 5.5
253
30
12.0
84.0
17.0
7.5
5
4.5 - 5.5
256
30
15.0
67.0
13.0
7.0
5
4.5 - 5.5
277
30
3.3
300.0
30.0
15.0
12
10.8 - 13.2
121
15
5.0
200.0
20.0
15.0
12
10.8 - 13.2
114
15
9.0
111.0
23.0
9.0
12
10.8 - 13.2
114
15
12.0
84.0
17.0
7.5
12
10.8 - 13.2
113
15
15.0
67.0
13.0
7.0
3.3
3.0 - 3.6
409
55
5.0
200.0
20.0
15.0
3.3
3.0 - 3.6
446
55
9.0
111.0
23.0
9.0
3.3
3.0 - 3.6
433
55
12.0
84.0
17.0
7.5
3.3
3.0 - 3.6
415
55
3.3
300.0
30.0
15.0
Other input/output combinations are available (i.e. 24 VDC Input).
Contact the factory for details at: [email protected]
Efficiency
(%, Typ)
77
76
79
78
72
69
73
73
74
74
68
70
73
Fuse Rating
Slow-Blow
(mA)
500
500
500
500
500
200
200
200
200
750
750
750
750
Derating Curve
Notes:
1. Output load regulation is specified for a load change of 10% to 100%.
2. When measuring output ripple, it is recommended that an external 0.33 µF ceramic
capacitor be placed from the +Vout pin to the -Vout pin.
3. During operation, care must be taken not to exceed the specified input range of the unit
or to allow the output load to drop below the specified minimum (10% of full load).
Operating the unit under either of these conditions could cause damage to the unit.
4. These converters are specified for operation without external components. However,
in some applications the addition of input/output capacitors will enhance stability and
reduce output ripple. Recommended capacitor values are:
Vin
Input
Capacitor
3.3 VDC
5 VDC
12 VDC
4.7 µF
4.7 µF
2.2 µF
Vout
Output
Capacitor
3.3 VDC
5 VDC
9 VDC
12 VDC
15 VDC
10.0 µF
10.0 µF
4.7 µF
2.2 µF
1.0 µF
For applications requiring very low output noise levels,
a simple LC filter should be effective.
5. It is recommended that a fuse be used on the input of
a power supply for protection. See the Model Selection
table above for the correct rating.
Mechanical Dimensions
Recommended Solder Profile
Pin Connections
Pin Description
1
-Vin
2
+Vin
3
NC
4
-Vout
NC = No Connection
Pin
5
6
7
8
Description
+Vout
NC
NC
NC
Board Layout
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
• Pin 1 is marked by a “dot” or indentation on the unit
MicroPower Direct
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: [email protected]
Similar pages