MPD LF152ESI Low cost, single output 1w high isolation smt dc/dc converter Datasheet

LF100ESI Series
Low Cost, Single Output
1W High Isolation SMT
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
• 1W Output Power
• Ultra-Miniature SMT Case
• 3,000 VDC Isolation
• UL Approved (File E245422)
• Single Output
• Low 0.24” Profile
• >3.5 MHour MTBF
• 3.3, 5V, & 12V Inputs
• LOWEST COST!
Input
Parameter
Conditions
3.3 VDC Input
Input Voltage Range
Min.
Typ.
Max.
3.0
3.3
3.6
5 VDC Input
4.5
5.0
5.5
12 VDC Input
10.8
12.0
13.2
Reverse Polarity Input Current
Input Filter
Units
VDC
1.0
A
Max.
Units
±1.2
%
Capacitor
Output
Parameter
Conditions
Min.
Output Voltage Accuracy
Typ.
±3.0
Line Regulation
For Vin Change of 1%
Load Regulation
%
See Model Selection Guide
Ripple & Noise (20 MHz)
60
120
mV P - P
Temperature Coefficient
±0.01
±0.02
%/ºC
Max.
Units
Output Short Circuit
Momentary (0.5 Sec.)
General
Parameter
Conditions
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Min.
60 Seconds
3,000
500 VDC
1,000
100 kHz, 1V
Switching Frequency
Typ.
VDC
M⍀
70
pF
100
kHz
Environmental
Parameter
Conditions
Operating Temperature Range
Ambient
Storage Temperature Range
Min.
Typ.
Max.
-40
+25
+85
ºC
+125
ºC
95
%
-55
Cooling
Units
Free Air Convection
Humidity
RH, Non-condensing
Physical
Case Size
0.60 x 0.30 x 0.24 Inches (15.24 x 7.5 x 6.0 mm)
Case Material
Non-Conductive Black Plastic (UL94-V0)
Weight
0.05 Oz (1.5g)
Reliability Specifications
MicroPower Direct
Parameter
292 Page Street
Suite D
Stoughton, MA 02072
USA
MTBF
Conditions
Min.
MIL HDBK 217F, 25ºC, Gnd Benign
Typ.
Max.
3.5
Units
MHours
Safety Standards
UL 1950, EN 60950, IEC 60950
Safety Approvals
UL, cUL; File No. E245422
Absolute Maximum Ratings
T: (781) 344-8226
F: (781) 344-8481
E: [email protected]
W: www.micropowerdirect.com
Parameter
Conditions
Input Voltage Surge (1 Sec)
Lead Temperature
Min.
Typ.
-0.7
5 VDC Input
-0.7
7.0
12 VDC Input
-0.7
15.0
1.5 mm From Case For 10 Sec
Internal Power Dissipation
Max.
3.3 VDC Input
All Models
VDC
260.0
ºC
450
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com
Units
7.0
www.micropowerdirect.com
Model Selection Guide
Model
Number
LF101ESI
LF102ESI
LF103ESI
LF104ESI
LF111ESI
LF112ESI
LF113ESI
LF114ESI
LF151ESI
LF152ESI
LF153ESI
Input
Voltage (VDC)
Nominal
Range
5
4.5 - 5.5
5
4.5 - 5.5
5
4.5 - 5.5
5
4.5 - 5.5
12
10.8 - 13.2
12
10.8 - 13.2
12
10.8 - 13.2
12
10.8 - 13.2
3.3
3.0 - 3.6
3.3
3.0 - 3.6
3.3
3.0 - 3.6
Output
Load
Current (mA)
Voltage Current
Current Regulation
Full-Load No-Load (VDC) (mA, Max) (mA, Min) (%, Max)
285
30
5.0
200.0
20.0
15.0
266
30
9.0
111.0
23.0
9.0
256
30
12.0
84.0
17.0
7.5
250
30
15.0
67.0
13.0
7.0
116
15
5.0
200.0
20.0
15.0
110
15
9.0
111.0
23.0
9.0
105
15
12.0
84.0
17.0
7.5
103
15
15.0
67.0
13.0
7.0
415
55
5.0
200.0
20.0
15.0
433
55
9.0
111.0
23.0
9.0
433
55
12.0
84.0
17.0
7.5
Notes:
1. Output load regulation is specified for a load change of 20% to 100%.
2. When measuring output ripple, it is recommended that an external 0.33 µF ceramic capacitor be placed from
the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units.
3. During operation, care must be taken not to exceed the specified input range of the unit or to allow the output
load to drop below the specified minimum (10% of full load). Operating the unit under either of these conditions
could cause damage to the unit.
4. These converters are specified for operation without external components. However, in some applications the
addition of input/output capacitors will enhance stability and reduce output ripple. Recommended capacitor values
are:
Vin
3.3 VDC
5 VDC
12 VDC
Input
Capacitor
4.7 µF
4.7 µF
2.2 µF
Vout
5 VDC
9 VDC
12 VDC
15 VDC
70
75
78
80
72
76
79
81
73
70
70
Fuse Rating
Slow-Blow
(mA)
500
500
500
500
200
200
200
200
750
750
750
Derating Curve
Output
Capacitor
4.7 µF
2.2 µF
1.0 µF
0.47 µF
For applications requiring very low output noise levels, a simple LC filter should be effective.
5. It is recommended that a fuse be used on the
input of a power supply for protection. See the
Model Selection table above for the correct rating.
Pin Connections
Mechanical Dimensions
Efficiency
(%, Typ)
Pin
1
2
3
5
6
Recommended Solder Profile
Description
Pin Description
-Vin
7
NC
+Vin
8
+Vout
NC
10
NC
-Vout
11
NC
NC
12
NC
NC = No Connection
Board Layout
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
• Pin 1 is marked by a “dot” or indentation on the unit
MicroPower Direct
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: [email protected]
Similar pages