TI1 LF156QML Lf156qml jfet input operational amplifier Datasheet

LF156QML
LF156QML JFET Input Operational Amplifiers
Literature Number: SNOSAN9
LF156QML
JFET Input Operational Amplifiers
General Description
Applications
This is the first monolithic JFET input operational amplifier to
incorporate well matched, high voltage JFETs on the same
chip with standard bipolar transistors (BI-FET™ Technology).
This amplifier features low input bias and offset currents/low
offset voltage and offset voltage drift, coupled with offset
adjust which does not degrade drift or common-mode rejection. The device is also designed for high slew rate, wide
bandwidth, extremely fast settling time, low voltage and
current noise and a low 1/f noise corner.
n
n
n
n
n
n
n
Features
Advantages
n Replace expensive hybrid and module FET op amps
n Rugged JFETs allow blow-out free handling compared
with MOSFET input devices
n Excellent for low noise applications using either high or
low source impedance — very low 1/f corner
n Offset adjust does not degrade drift or common-mode
rejection as in most monolithic amplifiers
n New output stage allows use of large capacitive loads
(5,000 pF) without stability problems
n Internal compensation and large differential input voltage
capability
Precision high speed integrators
Fast D/A and A/D converters
High impedance buffers
Wideband, low noise, low drift amplifiers
Logarithmic amplifiers
Photocell amplifiers
Sample and Hold circuits
Common Features
n Low input bias current:
n Low Input Offset Current:
n High input impedance:
n Low input noise current:
n High common-mode rejection ratio:
n Large dc voltage gain:
Uncommon Features
n Extremely fast settling
time to 0.01%
n Fast slew rate
n Wide gain bandwidth
n Low input noise voltage
30pA
3pA
1012Ω
100 dB
106 dB
1.5µs
12V/µs
5MHz
12
Ordering Information
NS PART NUMBER
SMD PART NUMBER
LF156H/883
NS PACKAGE NUMBER
PACKAGE DISCRIPTION
H08C
8LD Metal Can
Connection Diagrams
Metal Can Package (H)
20145914
Top View
See NS Package Number H08C
BI-FET™, BI-FET II™ are trademarks of National Semiconductor Corporation.
© 2006 National Semiconductor Corporation
DS201459
www.national.com
LF156QML JFET Input Operational Amplifiers
March 2006
LF156QML
Simplified Schematic
20145901
*3pF in LF357 series.
Detailed Schematic
20145913
*C = 3pF in LF357 series.
www.national.com
2
LF156QML
Absolute Maximum Ratings (Note 1)
Input Voltage Range (Note 4)
± 22V
± 40V
± 20V
Output Short Circuit Duration
Continuous
Supply Voltage
Differential Input Voltage
TJmax
150˚C
Power Dissipation at TA = 25˚C (Notes 2, 3)
Still Air
560 mW
500 LF/Min Air Flow
1200 mW
Thermal Resistance
θJA
Still Air
162˚C/W
400 LF/Min Air Flow
89˚C/W
θJC
32˚C/W
−65˚C ≤ TA ≤ +150˚C
Storage Temperature Range
Lead Temperature (Soldering 10 sec.)
300˚C
ESD tolerance (Note 5)
1200V
Quality Conformance Inspection
MIL-STD-883, Method 5005 - Group A
Subgroup
Description
Temp ( C)
1
Static tests at
+25
2
Static tests at
+125
3
Static tests at
-55
4
Dynamic tests at
+25
5
Dynamic tests at
+125
6
Dynamic tests at
-55
7
Functional tests at
+25
8A
Functional tests at
+125
8B
Functional tests at
-55
9
Switching tests at
+25
10
Switching tests at
+125
11
Switching tests at
-55
3
www.national.com
LF156QML
LF156 Electrical Characteristics
DC Parameters
The following conditions apply, unless otherwise specified.
DC: VCC = ± 5V, VCM = 0V, RS = 50Ω
Symbol
VIO
IIO
+IIB
-I IB
Parameter
Input Offset Voltage
Input Offset Current
Input Bias Current
Input Bias Current
Conditions
Notes
Subgroups
Min
Max
Unit
-5.0
5.0
mV
1
-7.0
7.0
mV
2, 3
-5.0
5.0
mV
1
-7.0
7.0
mV
2, 3
-0.02
0.02
nA
1
-20
20
nA
2, 3
VCC = ± 20V
-0.1
0.1
nA
1
-10
50
nA
2, 3
VCC = ± 20V, VCM = -16V
-0.1
0.1
nA
1
-10
50
nA
2, 3
VCC = ± 20V, VCM = 16V
-0.1
3.5
nA
1
-10
60
nA
2, 3
VCC = ± 20V
-0.1
0.1
nA
1
-10
50
nA
2, 3
-0.1
0.1
nA
1
-10
50
nA
2, 3
-0.1
3.5
nA
1
-10
60
nA
2, 3
VCC = ± 20V
VCC = ± 20V
VCC = ± 20V, VCM = -16V
VCC = ± 20V, VCM = 16V
+PSRR
Power Supply Rejection Ratio
+VCC = 20V to 10V,
-VCC = -20V
85
dB
1, 2, 3
-PSRR
Power Supply Rejection Ratio
-VCC = -20V to -10V,
+VCC = 20V
85
dB
1, 2, 3
CMRR
Common Mode Rejection Ratio VCM = ± 11V
85
dB
1, 2, 3
ICC
Power Supply Current
+IOS
-IOS
Short Circuit Current
Short Circuit Current
VO = 0V
VO = 0V
VCM
Common Mode Voltage Range
+VOP
Output Voltage Swing
RL = 10KΩ
-VOP
Output Voltage Swing
RL = 10KΩ
AVS
Large Signal Voltage Gain
RL = 2KΩ, VO = 0 to 10V
(Note 6)
mA
1
14
mA
2, 3
-45
-15
mA
1
-35
-10
mA
2
-65
-15
mA
3
15
45
mA
1
10
35
mA
2
15
65
mA
3
-11
11
V
1, 2, 3
V
4, 5, 6
12
RL = 2KΩ
(Note 6)
10
-12
RL = 2KΩ
(Note 6)
RL = 2KΩ, VO = 0 to -10V
www.national.com
7.0
4
-10
V
4, 5, 6
V
4, 5, 6
V
4, 5, 6
50
V/mV
4
25
V/mV
5, 6
50
V/mV
4
25
V/mV
5, 6
LF156QML
LF156 Electrical Characteristics
(Continued)
AC Parameters
The following conditions apply, unless otherwise specified.
AC: VCC = ± 5V, VCM = 0V, RS = 50Ω
Symbol
Parameter
+SR
Slew Rate
-SR
Slew Rate
Conditions
AV = 1, RLOAD = 2KΩ,
CL = 100pfd,
VI = -5V to +5V
AV = 1, RL = 2KΩ,
CL = 100pF,
VI = +5V to -5V
Notes
Unit
Subgroups
7.5
V/µS
7
7.5
V/µS
7
Min
Max
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate condition for which the device is
functional, but do not guarantee specific performance limits . For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed
specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test
conditions.
Note 2: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax(maximum junction temperature), θJA(package junction
to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any temperature is PD=(TJmax−TA)/θJA or the number
given in the Absolute Maximum Ratings, whichever is lower.
Note 3: Maximum power dissipation (PDmax)is defined by the package characteristics. Operating the part near the PDmax may cause the part to operate outside
guaranteed limits.
Note 4: Unless otherwise specified the absolute maximum negative input voltage is equal to the negative power supply voltage.
Note 5: Human body model, 100pF discharged through 1.5KΩ.
Note 6: Parameter guaranteed by CMRR test.
5
www.national.com
LF156QML
Typical DC Performance Characteristics
Input Bias Current
Input Bias Current
20145938
20145937
Input Bias Current
Voltage Swing
20145940
20145939
Supply Current
Supply Current
20145942
20145941
www.national.com
6
Negative Current Limit
LF156QML
Typical DC Performance Characteristics
(Continued)
Positive Current Limit
20145943
20145944
Positive Common-Mode
Input Voltage Limit
Negative Common-Mode
Input Voltage Limit
20145945
20145946
Open Loop Voltage Gain
Output Voltage Swing
20145948
20145947
7
www.national.com
LF156QML
Typical AC Performance Characteristics
Gain Bandwidth
Normalized Slew Rate
20145950
20145951
Output Impedance
Output Impedance
20145953
20145952
LF156 Large Signal Puls
Response, AV = +1
LF156 Small Signal Pulse
Response, AV = +1
20145909
20145906
www.national.com
8
Inverter Settling Time
LF156QML
Typical AC Performance Characteristics
(Continued)
Open Loop Frequency Response
20145956
20145957
Bode Plot
Common-Mode Rejection Ratio
20145959
20145961
Power Supply Rejection Ratio
20145963
9
www.national.com
LF156QML
Typical AC Performance Characteristics
Undistorted Output Voltage Swing
(Continued)
Equivalent Input Noise Voltage
20145964
20145965
Equivalent Input Noise
Voltage (Expanded Scale)
20145966
www.national.com
10
These are op amps with JFET input devices. These JFETs
have large reverse breakdown voltages from gate to source
and drain eliminating the need for clamps across the inputs.
Therefore large differential input voltages can easily be accommodated without a large increase in input current. The
maximum differential input voltage is independent of the
supply voltages. However, neither of the input voltages
should be allowed to exceed the negative supply as this will
cause large currents to flow which can result in a destroyed
unit.
Exceeding the negative common-mode limit on either input
will force the output to a high state, potentially causing a
reversal of phase to the output. Exceeding the negative
common-mode limit on both inputs will force the amplifier
output to a high state. In neither case does a latch occur
since raising the input back within the common-mode range
again puts the input stage and thus the amplifier in a normal
operating mode.
Exceeding the positive common-mode limit on a single input
will not change the phase of the output however, if both
inputs exceed the limit, the output of the amplifier will be
forced to a high state.
Typical Circuit Connections
VOS Adjustment
20145967
These amplifiers will operate with the common-mode input
voltage equal to the positive supply. In fact, the commonmode voltage can exceed the positive supply by approximately 100 mV independent of supply voltage and over the
full operating temperature range. The positive supply can
therefore be used as a reference on an input as, for example, in a supply current monitor and/or limiter.
Precautions should be taken to ensure that the power supply
for the integrated circuit never becomes reversed in polarity
or that the unit is not inadvertently installed backwards in a
socket as an unlimited current surge through the resulting
forward diode within the IC could cause fusing of the internal
conductors and result in a destroyed unit.
All of the bias currents in these amplifiers are set by FET
current sources. The drain currents for the amplifiers are
therefore essentially independent of supply voltage.
As with most amplifiers, care should be taken with lead
dress, component placement and supply decoupling in order
to ensure stability. For example, resistors from the output to
an input should be placed with the body close to the input to
minimize “pickup” and maximize the frequency of the feedback pole by minimizing the capacitance from the input to
ground.
A feedback pole is created when the feedback around any
amplifier is resistive. The parallel resistance and capacitance
from the input of the device (usually the inverting input) to AC
ground set the frequency of the pole. In many instances the
frequency of this pole is much greater than the expected 3dB
frequency of the closed loop gain and consequently there is
• VOS is adjusted with a 25k potentiometer
• The potentiometer wiper is connected to V+
• For potentiometers with temperature coefficient of 100
ppm/˚C or less the additional drift with adjust is ≈ 0.5µV/
˚C/mV of adjustment
• Typical overall drift: 5µV/˚C ± (0.5µV/˚C/mV of adj.)
Driving Capacitive Loads
20145968
* LF156 R = 5k
Due to a unique output stage design, these amplifiers
have the ability to drive large capacitive loads and still
maintain stability. CL(MAX) . 0.01µF.
Overshoot ≤ 20%
Settling time (ts) . 5µs
11
www.national.com
LF156QML
negligible effect on stability margin. However, if the feedback
pole is less than approximately six times the expected 3 dB
frequency a lead capacitor should be placed from the output
to the input of the op amp. The value of the added capacitor
should be such that the RC time constant of this capacitor
and the resistance it parallels is greater than or equal to the
original feedback pole time constant.
Application Hints
LF156QML
Typical Applications
Settling Time Test Circuit
20145916
• Settling time is tested with the LF156 connected as unity gain inverter.
• FET used to isolate the probe capacitance
• Output = 10V step
Large Signal Inverter Output, VOUT (from Settling Time Circuit)
LF356
20145918
www.national.com
12
LF156QML
Typical Applications
(Continued)
Low Drift Adjustable Voltage Reference
20145920
•
•
•
•
∆ VOUT/∆T = ± 0.002%/˚C
All resistors and potentiometers should be wire-wound
P1: drift adjust
P2: VOUT adjust
Fast Logarithmic Converter
20145921
•
•
•
•
•
Dynamic range: 100µA ≤ Ii ≤ 1mA (5 decades), |VO| = 1V/decade
Transient response: 3µs for ∆Ii = 1 decade
C1, C2, R2, R3: added dynamic compensation
VOS adjust the LF156 to minimize quiescent error
RT: Tel Labs type Q81 + 0.3%/˚C
13
www.national.com
LF156QML
Typical Applications
(Continued)
Precision Current Monitor
20145931
• VO = 5 R1/R2 (V/mA of IS)
• R1, R2, R3: 0.1% resistors
8-Bit D/A Converter with Symmetrical Offset Binary Operation
20145932
• R1, R2 should be matched within ± 0.05%
• Full-scale response time: 3µs
EO
www.national.com
B1 B2 B3 B4 B5 B6 B7 B8
Comments
+9.920
1
1
1
1
1
1
1
1
+0.040
1
0
0
0
0
0
0
0
(+) Zero-Scale
−0.040
0
1
1
1
1
1
1
1
(−) Zero-Scale
−9.920
0
0
0
0
0
0
0
0
Negative Full-Scale
14
Positive Full-Scale
LF156QML
Typical Applications
(Continued)
Wide BW Low Noise, Low Drift Amplifier
20145970
•
Parasitic input capacitance C1 . 3pF interacts with feedback elements and creates undesirable high frequency pole. To
compensate add C2 such that: R2 C2 . R1 C1.
Boosting the LF156 with a Current Amplifier
20145973
•
•
IOUT(MAX).150mA (will drive RL≥ 100Ω)
• No additional phase shift added by the current amplifier
15
www.national.com
LF156QML
Typical Applications
(Continued)
3 Decades VCO
20145924
R1, R4 matched. Linearity 0.1% over 2 decades.
Isolating Large Capacitive Loads
20145922
• Overshoot 6%
• ts 10µs
• When driving large CL, the VOUT slew rate determined by CL and IOUT(MAX):
www.national.com
16
LF156QML
Typical Applications
(Continued)
Low Drift Peak Detector
20145923
•
•
•
•
By adding D1 and Rf, VD1=0 during hold mode. Leakage of D2 provided by feedback path through Rf.
Leakage of circuit is essentially Ib plus capacitor leakage of Cp.
Diode D3 clamps VOUT (A1) to VIN−VD3 to improve speed and to limit reverse bias of D2.
Maximum input frequency should be << 1⁄2πRfCD2 where CD2 is the shunt capacitance of D2.
High Impedance, Low Drift Instrumentation Amplifier
20145926
• System VOS adjusted via A2 VOS adjust
• Trim R3 to boost up CMRR to 120 dB. Instrumentation amplifier resistor array recommended for best accuracy and lowest drift
17
www.national.com
LF156QML
Typical Applications
(Continued)
Fast Sample and Hold
20145933
• Both amplifiers (A1, A2) have feedback loops individually closed with stable responses (overshoot negligible)
• Acquisition time TA, estimated by:
• LF156 develops full Sr output capability for VIN ≥ 1V
• Addition of SW2 improves accuracy by putting the voltage drop across SW1 inside the feedback loop
• Overall accuracy of system determined by the accuracy of both amplifiers, A1 and A2
www.national.com
18
LF156QML
Typical Applications
(Continued)
High Accuracy Sample and Hold
20145927
• By closing the loop through A2, the VOUT accuracy will be determined uniquely by A1.
No VOS adjust required for A2.
• TA can be estimated by same considerations as previously but, because of the added
propagation delay in the feedback loop (A2) the overshoot is not negligible.
• Overall system slower than fast sample and hold
• R1, CC: additional compensation
• Use LF156 for
j Fast settling time
j Low VOS
High Q Notch Filter
20145934
• 2R1 = R = 10MΩ
2C = C1 = 300pF
• Capacitors should be matched to obtain high Q
• fNOTCH = 120 Hz, notch = −55 dB, Q > 100
• Use LF155 for
j Low IB
j Low supply current
19
www.national.com
LF156QML
Revision History
Date
Released
03/10/06
www.national.com
Revision
A
Section
Originator
New Released, Corporate format.
Electrical Section Delete Drift Value
table.
20
R. Malone
Changes
New Release, Corporate format 1 MDS
data sheet converted into a Corp. data
sheet format. Following MDS data sheet
will be Archived MNLF156-X, Rev. 2A0.
Delete Drift Value table from Electrical
Section. Reson: Referenced product is
883 only.
LF156QML JFET Input Operational Amplifiers
Physical Dimensions
inches (millimeters) unless otherwise noted
Metal Can Package (H)
NS Package Number H08C
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products
Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain
no ‘‘Banned Substances’’ as defined in CSP-9-111S2.
Leadfree products are RoHS compliant.
National Semiconductor
Americas Customer
Support Center
Email: [email protected]
Tel: 1-800-272-9959
www.national.com
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
Email: [email protected]
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Support Center
Email: [email protected]
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: [email protected]
Tel: 81-3-5639-7560
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and Automotive www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
www.ti.com/video
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
Similar pages