FCI LM1117-ADJ-252 800ma low-dropout linear regulator temperature range output current 800ma Datasheet

LM1117 800mA Low-dropout Linear Regulator
LM1117
800mA Low-Dropout Linear Regulator
General Description
Features
The LM1117 is a series of low dropout voltage regulators
with a dropout of 1.2V at 800mA of load current. It has the
same pin-out as National Semiconductor’s industry standard
LM317.
The LM1117 is available in an adjustable version, which can
set the output voltage from 1.25V to 13.8V with only two external resistors. In addition, it is also available in three fixed
voltages, 2.85V, 3.3V, and 5V.
n
n
n
n
n
n
n
The LM1117 offers current limiting and thermal shutdown. Its
circuit includes a zener trimmed bandgap reference to assure output voltage accuracy to within ± 1%.
The LM1117 series is available in SOT-223, TO-220, and
TO-252 D-PAK packages. A minimum of 10µF tantalum capacitor is required at the output to improve the transient response and stability.
Applications
n
n
n
n
n
Available in 2.85V, 3.3V, 5V, and Adjustable Versions
Space Saving SOT-223 Package
Current Limiting and Thermal Protection
Output Current
800mA
Temperature Range
0˚C to 125˚C
Line Regulation
0.2% (Max)
Load Regulation
0.4% (Max)
2.85V Model for SCSI-2 Active Termination
Post Regulator for Switching DC/DC Converter
High Efficiency Linear Regulators
Battery Charger
Battery Powered Instrumentation
Typical Application
Active Terminator for SCSI-2 Bus
Fixed Output Regulator
1
LM1117 800mA Low-dropout Linear Regulator
Ordering Information
Package
3-lead SOT-223
3-lead TO-220
Temperature Range
Packing
0˚C to +125˚C
LM1117-ADJ-223
Tape and Reel
LM1117-2.85-223
Tape and Reel
LM1117-3.3-223
Tape and Reel
LM1117-5.0-223
Tape and Reel
LM1117-ADJ-220
Rails
5 lead available
LM1117-2.85-220
Rails
suffix add 220-5L
LM1117-3.3-220
Rails
LM1117-5.0-220
3-lead TO-252
Rails
LM1117-ADJ-252
Tape and Reel
5 lead available
LM1117-2.85-252
Tape and Reel
suffix add 252-5L
LM1117-3.3-252
Tape and Reel
LM1117-5.0-252
Tape and Reel
Block Diagram
2
LM1117 800mA Low-dropout Linear Regulator
Connection Diagrams
SOT-223
DS100919-4
Top View
TO-220
DS100919-2
Top View
TO-252
DS100919-38
Top View
3
LM1117 800mA Low-dropout Linear Regulator
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
TO-220 Package
260˚C, 10 sec
SOT-223 Package
260˚C, 4 sec
ESD Tolerance (Note 3)
2000V
Operating Ratings (Note 1)
Maximum Input Voltage (VIN to GND)
LM1117-ADJ, LM1117-3.3,
LM1117-5.0
20V
Power Dissipation (Note 2)
Internally Limited
Junction Temperature (TJ )
(Note 2)
150˚C
Storage Temperature Range
Input Voltage (VIN to GND)
LM1117-ADJ, LM1117-3.3,
LM1117-5.0
15V
LM1117-2.85
10V
Junction Temperature Range (T J)
(Note 2)
-65˚C to 150˚C
0˚C to 125˚C
Lead Temperature
Electrical Characteristics
Typicals and limits appearing in normal type apply for T
tion temperature range for operation, 0˚C to 125˚C.
Symbol
VREF
VOUT
∆VOUT
∆V OUT
Output Voltage
Line Regulation
(Note 6)
Load Regulation
(Note 6)
= 25˚C. Limits appearing in Boldface type apply over the entire juncMin
(Note 5)
Typ
(Note 4)
Max
(Note 5)
Units
1.238
1.225
1.250
1.250
1.262
1.270
V
V
LM1117-2.85
IOUT =10mA, VIN=4.85V, TJ=25˚C
O≤I OUT≤800mA, 4.25V≤ VIN≤10V
O≤IOUT ≤500mA, VIN=4.10V
2.820
2.790
2.790
2.850
2.850
2.850
2.880
2.910
2.910
V
V
V
LM1117-3.3
I OUT=10mA, VIN=5V TJ=25˚C
O≤I OUT≤800mA, 4.75V≤ VIN≤10V
3.267
3.235
3.300
3.300
3.333
3.365
V
V
LM1117-5.0
I OUT=10mA, VIN=7V, TJ=25˚C
O≤I OUT≤ 800mA, 6.5V≤ VIN≤12V
4.950
4.900
5.000
5.000
5.050
5.100
V
V
Parameter
Reference Voltage
J
Conditions
LM1117-ADJ
IOUT=10mA, VIN-VOUT=2V, TJ=25˚C
10mA≤I OUT≤ 800mA, 1.4V≤
VIN-VOUT≤10V
LM1117-ADJ
IOUT=10mA, 1.5V≤ VIN-VOUT≤13.75V
0.035
0.2
%
LM1117-2.85
I OUT=0mA, 4.25V≤ VIN≤10V
1
6
mV
LM1117-3.3
I OUT=0mA, 4.75V≤ VIN≤15V
1
6
mV
LM1117-5.0
I OUT=0mA, 6.5V≤ VIN≤15V
1
10
mV
LM1117-ADJ
VIN-V OUT=3V, 10≤IOUT≤800mA
0.2
0.4
%
LM1117-2.85
V IN=4.25V, 0≤IOUT≤800mA
1
10
mV
LM1117-3.3
V IN=4.75V, 0≤IOUT≤800mA
1
10
mV
LM1117-5.0
V IN=6.5V, 0≤IOUT≤800mA
VIN-V OUT
ILIMIT
Dropout Voltage
(Note 7)
1
15
mV
IOUT=100mA
1.10
1.20
V
IOUT=500mA
1.15
1.25
V
IOUT=800mA
1.20
1.30
V
1200
1500
mA
1.7
5
mA
Current Limit
VIN-VOUT=5V, TJ=25˚C
Minimum Load
Current (Note 8)
LM1117-ADJ
VIN=15V
800
4
LM1117 800mA Low-dropout Linear Regulator
Electrical Characteristics
(Continued)
Typicals and limits appearing in normal type apply for T
tion temperature range for operation, 0˚C to 125˚C.
Symbol
= 25˚C. Limits appearing in Boldface type apply over the entire juncTyp
(Note 4)
Max
(Note 5)
Units
LM1117-2.85
VIN≤10V
5
10
mA
LM1117-3.3
V IN≤15V
5
10
mA
Parameter
Quiescent Current
J
Min
(Note 5)
Conditions
LM1117-5.0
V IN≤15V
Thermal Regulation
TA=25˚C, 30ms Pulse
Ripple Regulation
fRIPPLE=120Hz, V IN-VOUT=3V
VRIPPLE=1VPP
Adjust Pin Current
Adjust Pin Current
Change
10≤ IOUT≤ 800mA,
1.4V≤ VIN-VOUT≤ 10V
Temperature Stability
60
5
10
mA
0.01
0.1
%/W
75
dB
60
120
µA
0.2
5
µA
0.5
%
0.3
%
(% of VOUT), 10Hz≤f≤10kHz
0.003
%
Thermal Resistance
Junction-to-Case
3-Lead SOT-223
3,5 -Lead TO-220
3,5 -Lead TO-252
15.0
3.0
10
˚C/W
˚C/W
˚C/W
Thermal Resistance
Junction-to-Ambient
(No heat sink;
No air flow)
3-Lead SOT-223
3,5 -Lead TO-220
3,5 -Lead TO-252(Note 9)
136
79
92
˚C/W
˚C/W
˚C/W
Long Term Stability
TA=125˚C, 1000Hrs
RMS Output Noise
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics.
Note 2: The maximum power dissipation is a function of TJ(max) , θJA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(max)–T A)/θJA. All numbers apply for packages soldered directly into a PC board.
Note 3: For testing purposes, ESD was applied using human body model, 1.5kΩ in series with 100pF.
Note 4: Typical Values represent the most likely parametric norm.
Note 5: All limits are guaranteed by testing or statistical analysis.
Note 6: Load and line regulation are measured at constant junction room temperature.
Note 7: The dropout voltage is the input/output differential at which the circuit ceases to regulate against further reduction in input voltage. It is measured when the
output voltage has dropped 100mV from the nominal value obtained at VIN=V OUT+1.5V.
Note 8: The minimum output current required to maintain regulation.
Note 9: Minimum pad size of 0.038in2
5
LM1117 800mA Low-dropout Linear Regulator
Typical Performance Characteristics
Dropout Voltage (VIN-V
OUT)
Short-Circuit Current
DS100919-22
DS100919-23
Load Regulation
LM1117-ADJ Ripple Rejection
LM1117-ADJ Ripple Rejection vs. Current
Temperature Stability
6
LM1117 800mA Low-dropout Linear Regulator
Typical Performance Characteristics
Adjust Pin Current
(Continued)
LM1117-2.85 Load Transient Response
LM1117-5.0 Load Transient Response
LM1117-2.85 Line Transient Response
LM1117-5.0 Line Transient Response
7
LM1117 800mA Low-dropout Linear Regulator
APPLICATION NOTE
1.0 External Capacitors/Stability
1.1 Input Bypass Capacitor
Figure 2, shows a typical application using a fixed output
regulator. The Rt1 and Rt2 are the line resistances. It is obvious that the V LOAD is less than the VOUT by the sum of the
voltage drops along the line resistances. In this case, the
load regulation seen at the RLOAD would be degraded from
the data sheet specification. To improve this, the load should
be tied directly to the output terminal on the positive side and
directly tied to the ground terminal on the negative side.
An input capacitor is recommended. A 10µF tantalum on the
input is a suitable input bypassing for almost all applications.
1.2 Adjust Terminal Bypass Capacitor
The adjust terminal can be bypassed to ground with a
pass capacitor (CADJ) to improve ripple rejection. This
pass capacitor prevents ripple from being amplified as
output voltage is increased. At any ripple frequency, the
pedance of the CADJ should be less than R1 to prevent
ripple from being amplified:
(2π*fRIPPLE*CADJ) < R1
bybythe
imthe
The R1 is the resistor between the output and the adjust pin.
Its value is normally in the range of 100-200Ω. For example,
with R1=124Ω and fRIPPLE=120Hz, the CADJ should be >
11µF.
1.3 Output Capacitor
The output capacitor is critical in maintaining regulator stability, and must meet the required conditions for both minimum
amount of capacitance and ESR (Equivalent Series Resistance). The minimum output capacitance required by the
LM1117 is 10µF, if a tantalum capacitor is used. Any increase
of the output capacitance will merely improve the loop stability and transient response. The ESR of the output capacitor
should be less than 0.5Ω. In the case of the adjustable regulator, when the CADJ is used, a larger output capacitance
(22µf tantalum) is required.
2.0 Output Voltage
The LM1117 adjustable version develops a 1.25V reference
voltage, VREF, between the output and the adjust terminal.
As shown in Figure 1, this voltage is applied across resistor
R1 to generate a constant current I1. The current IADJ from
the adjust terminal could introduce error to the output. But
since it is very small (60µA) compared with the I1 and very
constant with line and load changes, the error can be ignored. The constant current I1 then flows through the output
set resistor R2 and sets the output voltage to the desired
level.
For fixed voltage devices, R1 and R2 are integrated inside
the devices.
FIGURE 2. Typical Application using Fixed Output
Regulator
When the adjustable regulator is used (Figure 3), the best
performance is obtained with the positive side of the resistor
R1 tied directly to the output terminal of the regulator rather
than near the load. This eliminates line drops from appearing
effectively in series with the reference and degrading regulation. For example, a 5V regulator with 0.05Ω resistance between the regulator and load will have a load regulation due
to line resistance of 0.05Ω x IL. If R1 (=125Ω) is connected
near the load, the effective line resistance will be 0.05Ω
(1+R2/R1) or in this case, it is 4 times worse. In addition, the
ground side of the resistor R2 can be returned near the
ground of the load to provide remote ground sensing and improve load regulation.
FIGURE 3. Best Load Regulation using Adjustable
Output Regulator
4.0 Protection Diodes
Under normal operation, the LM1117 regulators do not need
any protection diode. With the adjustable device, the internal
resistance between the adjust and output terminals limits the
current. No diode is needed to divert the current around the
regulator even with capacitor on the adjust terminal. The adjust pin can take a transient signal of ± 25V with respect to
the output voltage without damaging the device.
When a output capacitor is connected to a regulator and the
input is shorted to ground, the output capacitor will discharge
FIGURE 1. Basic Adjustable Regulator
3.0 Load Regulation
The LM1117 regulates the voltage that appears between its
output and ground pins, or between its output and adjust
pins. In some cases, line resistances can introduce errors to
the voltage across the load. To obtain the best load regulation, a few precautions are needed.
8
LM1117 800mA Low-dropout Linear Regulator
APPLICATION NOTE
(Continued)
into the output of the regulator. The discharge current depends on the value of the capacitor, the output voltage of the
regulator, and rate of decrease of V IN. In the LM1117 regulators, the internal diode between the output and input pins
can withstand microsecond surge currents of 10A to 20A.
With an extremely large output capacitor (≥1000 µF), and
with input instantaneously shorted to ground, the regulator
could be damaged.
In this case, an external diode is recommended between the
output and input pins to protect the regulator, as shown in
Figure 4.
FIGURE 5. Cross-sectional view of Integrated Circuit
Mounted on a printed circuit board. Note that the case
temperature is measured at the point where the leads
contact with the mounting pad surface
The LM1117 regulators have internal thermal shutdown to
protect the device from over-heating. Under all possible operating conditions, the junction temperature of the LM1117
must be within the range of 0˚C to 125˚C. A heatsink may be
required depending on the maximum power dissipation and
maximum ambient temperature of the application. To determine if a heatsink is needed, the power dissipated by the
regulator, PD , must be calculated:
IIN = IL + IG
PD = (VIN-VOUT)I L + VINIG
Figure 6 shows the voltages and currents which are present
in the circuit.
FIGURE 4. Regulator with Protection Diode
5.0 Heatsink Requirements
When an integrated circuit operates with an appreciable current, its junction temperature is elevated. It is important to
quantify its thermal limits in order to achieve acceptable performance and reliability. This limit is determined by summing
the individual parts consisting of a series of temperature
rises from the semiconductor junction to the operating environment. A one-dimensional steady-state model of conduction heat transfer is demonstrated in Figure 5. The heat generated at the device junction flows through the die to the die
attach pad, through the lead frame to the surrounding case
material, to the printed circuit board, and eventually to the
ambient environment. Below is a list of variables that may affect the thermal resistance and in turn the need for a heatsink.
RθJC(Component Variables)
FIGURE 6. Power Dissipation Diagram
RθCA (Application Variables)
Leadframe Size &
Material
Mounting Pad Size,
Material, & Location
No. of Conduction Pins
Placement of Mounting
Pad
Die Size
PCB Size & Material
Die Attach Material
Traces Length & Width
Molding Compound Size
and Material
Adjacent Heat Sources
Volume of Air
Ambient Temperatue
Shape of Mounting Pad
9
LM1117 800mA Low-dropout Linear Regulator
APPLICATION NOTE
needed since the package alone will dissipate enough heat
to satisfy these requirements. If the calculated value for θJA
falls below these limits, a heatsink is required.
As a design aid, Table 1 shows the value of the θJA of SOT223 and TO-252 for different heatsink area. The copper patterns that we used to measure these θJAs are shown at the
end of the Application Notes Section. Figure 7 and Figure 8
reflects the same test results as what are in the Table 1
Figure 9 and Figure 10 shows the maximum allowable power
dissipation vs. ambient temperature for the SOT-223 and
TO-252 device. Figures Figure 11 and Figure 12 shows the
maximum allowable power dissipation vs. copper area (in2)
for the SOT-223 and TO-252 devices. Please see AN1028
for power enhancement techniques to be used with SOT-223
and TO-252 packages.
(Continued)
The next parameter which must be calculated is the maximum allowable temperature rise, TR(max):
TR(max)=TJ(max)-TA(max)
where TJ(max) is the maximum allowable junction temperature (125˚C), and TA(max) is the maximum ambient temperature which will be encountered in the application.
Using the calculated values for TR(max) and PD, the maximum allowable value for the junction-to-ambient thermal resistance (θJA) can be calculated:
θJA = TR(max)/PD
If the maximum allowable value for θJA is found to be
≥136˚C/W for SOT-223 package or ≥79˚C/W for TO-220
package or ≥92˚C/W for TO-252 package, no heatsink is
TABLE 1. θJA Different Heatsink Area
Layout
Copper Area
Thermal Resistance
Top Side (in2)*
Bottom Side (in2)
(θJA,˚C/W) SOT-223
(θJA,˚C/W) TO-252
1
0.0123
0
136
103
2
0.066
0
123
87
3
0.3
0
84
60
4
0.53
0
75
54
5
0.76
0
69
52
6
1
0
66
47
7
0
0.2
115
84
8
0
0.4
98
70
9
0
0.6
89
63
10
0
0.8
82
57
11
0
1
79
57
12
0.066
0.066
125
89
13
0.175
0.175
93
72
14
0.284
0.284
83
61
15
0.392
0.392
75
55
16
0.5
0.5
70
53
*Tab of device attached to topside copper
FIGURE 8. θJA vs. 2oz Copper Area for TO-252
FIGURE 7. θJA vs. 1oz Copper Area for SOT-223
10
LM1117 800mA Low-dropout Linear Regulator
APPLICATION NOTE
FIGURE 9. Maximum Allowable Power Dissipation vs.
Ambient Temperature for SOT-223
(Continued)
FIGURE 10. Maximum Allowable Power Dissipation vs.
Ambient Temperature for TO-252
FIGURE 12. Maximum Allowable Power Dissipation vs.
2oz Copper Area for TO-252
11
FIGURE 11. Maximum Allowable Power Dissipation vs.
1oz Copper Area for SOT-223
LM1117 800mA Low-dropout Linear Regulator
Typical Application Circuits
Adjusting Output of Fixed Regulators
Regulator with Reference
5V Logic Regulator with Electronic Shutdown*
1.25V to 10V Adjustable Regulator with Improved
Ripple Rejection
Low Dropout Negative Supply
Battery Backed-Up Regulated Supply
Battery Backed-Up Regulated Supply
12
LM1117 800mA Low-dropout Linear Regulator
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
3-Lead TO-220 Package
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
3-Lead TO-252 Package
13
LM1117 800mA Low-dropout Linear Regulator
Physical Dimensions
inches (millimeters) unless otherwise noted
3-Lead SOT-223 Package
14
Similar pages