TI1 LM117KGMD8 Lm117qml 3-terminal adjustable regulator Datasheet

LM117QML
LM117QML 3-Terminal Adjustable Regulator
Literature Number: SNVS356C
LM117QML
3-Terminal Adjustable Regulator
General Description
The LM117 series of adjustable 3-terminal positive voltage
regulators is capable of supplying either 0.5A or 1.5A over a
1.2V to 37V output range. They are exceptionally easy to use
and require only two external resistors to set the output voltage. Further, both line and load regulation are better than
standard fixed regulators.
In addition to higher performance than fixed regulators, the
LM117 series offers full overload protection available only in
IC's. Included on the chip are current limit, thermal overload
protection and safe area protection. All overload protection
circuitry remains fully functional even if the adjustment terminal is disconnected.
Normally, no capacitors are needed unless the device is situated more than 6 inches from the input filter capacitors in
which case an input bypass is needed. An optional output capacitor can be added to improve transient response. The
adjustment terminal can be bypassed to achieve very high
ripple rejection ratios which are difficult to achieve with standard 3-terminal regulators.
Besides replacing fixed regulators, the LM117 is useful in a
wide variety of other applications. Since the regulator is “floating” and sees only the input-to-output differential voltage,
supplies of several hundred volts can be regulated as long as
the maximum input to output differential is not exceeded, i.e.,
avoid short-circuiting the output.
Also, it makes an especially simple adjustable switching regulator, a programmable output regulator, or by connecting a
fixed resistor between the adjustment pin and output, the
LM117 can be used as a precision current regulator. Supplies
with electronic shutdown can be achieved by clamping the
adjustment terminal to ground which programs the output to
1.2V where most loads draw little current.
For the negative complement, see LM137 series data sheet.
Features
■ Available with Radiation Guarantee
■
■
■
■
■
■
100 krad(Si)
— High Dose Rate
100 krad(Si)
— ELDRS Free
Guaranteed max. 0.3% load regulation (LM117)
Guaranteed 0.5A or 1.5A output current
Adjustable output down to 1.2V
Current limit constant with temperature
80 dB ripple rejection
Output is short-circuit protected
Ordering Information
NS Part Number
SMD Part Number
NS Package Number
Package Description
LM117E/883
E20A
20LD LCC
LM117H/883
H03A
3LD T0–39 Metal Can
LM117HRQMLV
(Note 12)
5962R9951703VXA
100 krad(Si)
H03A
3LD T0–39 Metal Can
LM117HRLQMLV (Note 13)
ELDRS Free
5962R9951705VXA
100 krad(Si)
H03A
3LD T0–39 Metal Can
LM117K/883
K02C
2LD T0–3 Metal Can
LM117KRQMLV
(Note 12)
5962R9951704VYA
100 krad(Si)
K02C
2LD T0–3 Metal Can
LM117WGRQMLV
(Note 12)
5962R9951703VZA
100 krad(Si)
WG16A
16LD Ceramic SOIC
LM117WGRLQMLV (Note 13)
ELDRS Free
5962R9951705VZA
100 krad(Si)
WG16A
16LD Ceramic SOIC
LM117GWRQMLV
(Note 12)
5962R9951706VZA
100 krad(Si)
WG16A
16LD Ceramic SOIC
LM117GWRLQMLV (Note 13)
ELDRS Free
5962R9951707VZA
100 krad(Si)
WG16A
16LD Ceramic SOIC
LM117H MDE (Note 13)
ELDRS Free
5962R9951705V9A
100 krad(Si)
(Note 1)
Bare Die
LM117H MDR
(Note 12)
5962R9951703V9A
100 krad(Si)
(Note 1)
Bare Die
LM117H MD8
(Note 1)
Bare Die
LM117KG MD8
(Note 1)
Bare Die
Note 1: FOR ADDITIONAL DIE INFORMATION, PLEASE VISIT THE HI REL WEB SITE AT: www.national.com/analog/space/level_die
© 2011 National Semiconductor Corporation
201436
www.national.com
LM117QML 3-Terminal Adjustable Regulator
September 6, 2011
LM117QML
Connection Diagrams
(TO-3)
Metal Can Package
(TO-39)
Metal Can Package
20143631
CASE IS OUTPUT
Bottom View
NS Package Number H03A
20143630
CASE IS OUTPUT
Bottom View
Steel Package
NS Package Number K02C
Ceramic SOIC
Chip Carrier
Ceramic Leadless
Chip Carrier
20143634
Top View
NS Package Number E20A
20143667
Top View
NS Package Number WG16A
(Note 5)
LM117 Series Packages
www.national.com
Part
Number
Suffix
Package
Design
Load
Current
K
TO-3
1.5A
H
T0–39
0.5A
WG, GW
Ceramic SOIC
0.5A
E
LCC
0.5A
2
LM117QML
20143608
Schematic Diagram
3
www.national.com
LM117QML
Absolute Maximum Ratings (Note 2)
Power Dissipation (Note 3)
Input-Output Voltage Differential
Storage Temperature
Internally Limited
+40V, −0.3V
−65°C ≤ TA ≤ +150°C
+150°C
300°C
Maximum Junction Temperature (TJmax
Lead Temperature Metal Package
Thermal Resistance
θJA
T0–3 Still Air
T0–3 500LF/Min Air flow
T0–39 Still Air
T0–39 500LF/Min Air flow
Ceramic SOIC Still Air “WG”
Ceramic SOIC 500LF/Min Air flow “WG”
Ceramic SOIC Still Air “GW”
Ceramic SOIC 500LF/Min Air flow “GW”
LCC Still Air
LCC 500LF/Min Air flow
39°C/W
14°C/W
186°C/W
64°C/W
115°C/W
66°C/W
130°C/W
80°C/W
88°C/W
62°C/W
θJC
T0–3
T0–39 Metal Can
Ceramic SOIC “WG”(Note 6)
Ceramic SOIC “GW”
LCC
Package Weight
T0–39 Metal Can
SOIC “WG”
SOIC “GW”
ESD Tolerance (Note 4)
1.9°C/W
21°C/W
3.4°C/W
7°C/W
12°C/W
960mg
365mg
410mg
3KV
Recommended Operating Conditions
−55°C ≤ TA ≤ +125°C
4.25V to 41.25V
Operating Temperature Range
Input Voltage Range
Quality Conformance Inspection
MIL-STD-883, Method 5005 - Group A
Subgroup
Description
Temp (°C)
1
Static tests at
+25
2
Static tests at
+125
3
Static tests at
-55
4
Dynamic tests at
+25
5
Dynamic tests at
+125
6
Dynamic tests at
-55
7
Functional tests at
+25
8A
Functional tests at
+125
8B
Functional tests at
-55
9
Switching tests at
+25
10
Switching tests at
+125
11
Switching tests at
-55
12
Settling time at
+25
13
Settling time at
+125
14
Settling time at
-55
www.national.com
4
LM117QML
5
www.national.com
LM117QML
LM117H & WG
Electrical Characteristics
DC Parameters
The following conditions apply, unless otherwise specified.
Symbol
IAdj
IQ
Parameter
Adjustment Pin Current
Minimum Load Current
VDiff = (VI − VO), IL = 8mA
Conditions
Notes
Min
Unit
VDiff = 3V
100
µA
1
VDiff = 3.3V
100
µA
2, 3
VDiff = 40V
100
µA
1, 2, 3
VDiff = 3V, VO = 1.7V
5.0
mA
1
VDiff = 3.3V, VO = 1.7V
5.0
mA
2, 3
1, 2, 3
VDiff = 40V, VO = 1.7V
VRef
VRLine
VRLoad
Reference Voltage
Line Regulation
Load Regulation
ΔIAdj / Load Adjustment Current Change
Subgroups
Max
5.0
mA
VDiff = 3V
1.2
1.3
V
1
VDiff = 3.3V
1.2
1.3
V
2, 3
VDiff = 40V
1.2
1.3
V
1, 2, 3
3V ≤ VDiff ≤ 40V,
VO = 1.2V
-8.9
8.9
mV
1
3.3V ≤ VDiff ≤ 40V,
VO = 1.2V
-22.2
22.2
mV
2, 3
VDiff= 3V,
IL = 10mA to 500mA
-15
15
mV
1
VDiff= 3.3V,
IL = 10mA to 500mA
-15
15
mV
2, 3
VDiff= 40V,
IL = 10mA to 150mA
-15
15
mV
1
VDiff= 40V,
IL = 10mA to 100mA
-15
15
mV
2, 3
VDiff = 3V,
IL = 10mA to 500mA
-5.0
5.0
µA
1
VDiff = 3.3V,
IL = 10mA to 500mA
-5.0
5.0
µA
2, 3
VDiff = 40V,
IL = 10mA to 150mA
-5.0
5.0
µA
1
VDiff = 40V,
IL = 10mA to 100mA
-5.0
5.0
µA
2, 3
3V ≤ VDiff ≤ 40V
-5.0
5.0
µA
1
ΔIAdj / Line
Adjustment Current Change
3.3V ≤ VDiff ≤ 40V
-5.0
5.0
µA
2, 3
IOS
Short Circuit Current
VDiff = 10V
0.45
1.6
A
1
θR
Thermal Regulation
TA = 25°C, t = 20mS, VDiff = 40V,
IL = 150mA
-6.0
6.0
mV
1
ICL
Current Limit
VDiff ≤ 15V
(Note 7)
0.5
A
1, 2, 3
VDiff = 40V
(Note 7)
0.15
A
1
Notes
Min
Unit
Subgroups
(Note 8)
66
dB
4, 5, 6
AC Parameters
Symbol
RR
Parameter
Ripple Rejection
www.national.com
Conditions
VI = +6.25V, VO = VRef,
ƒ= 120Hz, eI = 1VRMS,
IL = 125mA
6
Max
LM117QML
LM117K
Electrical Characteristics
DC Parameters
The following conditions apply, unless otherwise specified.
Symbol
IAdj
IQ
Parameter
Adjustment Pin Current
Minimum Load Current
VRef
VRLine
VRLoad
Reference Voltage
Line Regulation
Load Regulation
ΔIAdj / Load Adjustment Current Change
ΔIAdj / Line
Adjustment Current Change
VDiff = (VI − VO), IL = 10mA
Conditions
Notes
Min
Subgroups
Max
Unit
VDiff = 3V
100
µA
1
VDiff = 3.3V
100
µA
2, 3
VDiff = 40V
100
µA
1, 2, 3
VDiff = 3V, VO = 1.7V
5.0
mA
1
VDiff = 3.3V, VO = 1.7V
5.0
mA
2, 3
VDiff = 40V, VO = 1.7V
5.0
mA
1, 2, 3
VDiff = 3V
1.2
1.3
V
1
VDiff = 3.3V
1.2
1.3
V
2, 3
VDiff = 40V
1.2
1.3
V
1, 2, 3
3V ≤ VDiff ≤ 40V,
VO = 1.2V
-8.9
8.9
mV
1
3.3V ≤ VDiff ≤ 40V,
VO = 1.2V
-22.2
22.2
mV
2, 3
VDiff= 3V,
IL = 10mA to 1.5A
-15
15
mV
1
VDiff= 3.3V,
IL = 10mA to 1.5A
-15
15
mV
2, 3
VDiff= 40V,
IL = 10mA to 300mA
-15
15
mV
1
VDiff= 40V,
IL = 10mA to 195mA
-15
15
mV
2, 3
VDiff = 3V,
IL = 10mA to 1.5A
-5.0
5.0
µA
1
VDiff = 3.3V,
IL = 10mA to 1.5A
-5.0
5.0
µA
2, 3
VDiff = 40V,
IL = 10mA to 300mA
-5.0
5.0
µA
1
VDiff = 40V,
IL = 10mA to 195mA
-5.0
5.0
µA
2, 3
3V ≤ VDiff ≤ 40V
-5.0
5.0
µA
1
3.3V ≤ VDiff ≤ 40V
-5.0
5.0
µA
2, 3
1.6
3.4
A
1
-10.5
10.5
mV
1
IOS
Short Circuit Current
VDiff = 10V
θR
Thermal Regulation
TA = 25°C, t = 20mS,
VDiff = 40V, IL = 300mA
ICL
Current Limit
VDiff ≤ 15V
(Note 7)
1.5
A
1, 2, 3
VDiff = 40V
(Note 7)
0.3
A
1
Notes
Min
Unit
Subgroups
(Note 8)
66
dB
4, 5, 6
AC Parameters
Symbol
RR
Parameter
Ripple Rejection
Conditions
VI = +6.25V, VO = VRef,
ƒ= 120Hz, eI = 1VRMS,
IL = 0.5A
7
Max
www.national.com
LM117QML
LM117E
Electrical Characteristics
DC Parameters
The following conditions apply, unless otherwise specified.
Symbol
IAdj
IQ
Max
Unit
Subgroups
VDiff = 3V
100
µA
1
VDiff = 3.3V
100
µA
2, 3
VDiff = 40V
100
µA
1, 2, 3
VDiff = 3V, VO = 1.7V
5.0
mA
1
VDiff = 3.3V, VO = 1.7V
5.0
mA
2, 3
Parameter
Adjustment Pin Current
Minimum Load Current
VDiff = (VI − VO), IL = 8mA, PD ≤ 1.5W
Conditions
Notes
Min
VDiff = 40V, VO = 1.7V
VRef
VRLine
VRLoad
Reference Voltage
Line Regulation
Load Regulation
ΔIAdj / Load Adjustment Current Change
5.0
mA
1, 2, 3
VDiff = 3V
1.2
1.3
V
1
VDiff = 3.3V
1.2
1.3
V
2, 3
VDiff = 40V
1.2
1.3
V
1, 2, 3
3V ≤ VDiff ≤ 40V,
VO = 1.2V
-8.9
8.9
mV
1
3.3V ≤ VDiff ≤ 40V,
VO = 1.2V
-22.2
22.2
mV
2, 3
VDiff= 3V,
IL = 10mA to 100mA
-15
15
mV
1
VDiff= 3.3V,
IL = 10mA to 100mA
-15
15
mV
2, 3
VDiff= 40V,
IL = 10mA to 100mA
-15
15
mV
1,2
−25
25
mV
3
VDiff= 3V,
IL = 10mA to 500mA
-15
15
mV
1
VDiff= 3.3V,
IL = 10mA to 500mA
-15
15
mV
2, 3
VDiff = 3V,
IL = 10mA to 500mA
-5.0
5.0
µA
1
VDiff = 3.3V,
IL = 10mA to 500mA
-5.0
5.0
µA
2, 3
VDiff = 40V,
IL = 10mA to 100mA
-5.0
5.0
µA
1, 2, 3
3V ≤ VDiff ≤ 40V
-5.0
5.0
µA
1
3.3V ≤ VDiff ≤ 40V
-5.0
5.0
µA
2, 3
ΔIAdj / Line
Adjustment Current Change
IOS
Short Circuit Current
VDiff = 10V
0.45
1.6
A
1
θR
Thermal Regulation
TA = 25°C, t = 20mS,
VDiff = 40V, IL = 75mA
-6.0
6.0
mV
1
ICL
Current Limit
VDiff ≤ 15V
(Note 7)
0.5
A
1, 2, 3
VDiff = 40V
(Note 7)
0.15
A
1
Notes
Min
Unit
Subgroups
(Note 8)
66
dB
4, 5, 6
AC Parameters
Symbol
RR
Parameter
Ripple Rejection
www.national.com
Conditions
VI = +6.25V, VO = VRef,
ƒ= 120Hz, eI = 1VRMS,
IL = 100mA, CAdj = 10µf
8
Max
DC Parameters
Symbol
VO
VRLine
LM117QML
LM117H & WG
RH Electrical Characteristics
(Note 12, Note 13)
Parameter
Conditions
Output Voltage
Line Regulation
Notes
Min
Max
Unit
Subgroups
VI = 4.25V, IL = -5mA
1.2
1.3
V
1, 2, 3
VI = 4.25V, IL = -500mA
1.2
1.3
V
1, 2, 3
VI = 41.25V, IL = -5mA
1.2
1.3
V
1, 2, 3
VI = 41.25V, IL = -50mA
1.2
1.3
V
1, 2, 3
4.25V ≤ VI ≤ 41.25V,
IL = -5mA
-9.0
9.0
mV
1
-23
23
mV
2,3
-12
12
mV
1, 2, 3
-12
12
mV
1, 2, 3
VI = 6.25V,
VRLoad
-500mA ≤ IL ≤ -5mA
Load Regulation
VI = 41.25V,
-50mA ≤ IL ≤ -5mA
VRTh
Thermal Regulation
IAdj
Adjust Pin Current
ΔIAdj/ Line
Adjust Pin Current Change
ΔIAdj / Load Adjust Pin Current Change
IQ
Minimum Load Current
IOS
Output Short Circuit Current
VO (Recov) Output Voltage Recovery
VI = 14.6V, IL = -500mA
-12
12
mV
1
VI = 4.25V, IL = -5mA
-100
-15
µA
1, 2, 3
VI = 41.25V, IL = -5mA
-100
-15
µA
1, 2, 3
4.25V ≤ VI ≤ 41.25V,
IL = -5mA
-5.0
5.0
µA
1, 2, 3
-5.0
5.0
µA
1, 2, 3
VI = 4.25V,
Forced VO = 1.4V
-3.0
-0.5
mA
1, 2, 3
VI = 14.25V,
Forced VO = 1.4V
-3.0
-0.5
mA
1, 2, 3
VI = 41.25V,
Forced VO = 1.4V
-5.0
-1.0
mA
1, 2, 3
VI = 4.25V
-1.8
-0.5
A
1, 2, 3
VI = 40V
-0.5
-0.05
A
1, 2, 3
VI = 4.25V, RL = 2.5Ω,
CL = 20µF
1.2
1.3
V
1, 2, 3
1.2
1.3
V
1, 2, 3
1.2
1.3
V
2
1.2
1.3
V
1, 2, 3
Min
Max
Unit
Sub groups
VI = 6.25V,
-500mA ≤ IL ≤ -5mA
VI = 40V, RL = 250Ω
VO
Output Voltage
VI = 6.25V, IL = -5mA
VStart
Voltage Start-Up
VI = 4.25V, RL = 2.5Ω,
CL = 20µF, IL = -500mA
AC Parameters
(Note 9)
(Note 12, Note 13)
Symbol
Parameter
Conditions
Notes
VNO
Output Noise Voltage
VI = 6.25V, IL = -50mA
120
µVRMS
7
ΔVO / ΔVI
Line Transient Response
VI = 6.25V, ΔVI = 3V,
IL = -10mA
6.0
mV/V
7
ΔVO / ΔIL
Load Transient Response
VI = 6.25V, ΔIL = -200mA,
IL = -50mA
0.6
mV/mA
7
ΔVI / ΔVO
Ripple Rejection
VI = 6.25V, IL = -125mA,
EI = 1VRMS at ƒ = 2400Hz
dB
4
9
65
www.national.com
LM117QML
DC Drift Parameters
The following conditions apply, unless otherwise specified.
Deltas performed on QMLV devices at Group B, Subgroup 5, only.
Symbol
VO
Parameter
Output Voltage
Conditions
Notes
Min
Max
Unit
Subgroups
VI = 4.25V, IL = -5mA
-0.01
0.01
V
1
VI = 4.25V, IL = -500mA
-0.01
0.01
V
1
VI = 41.25V, IL = -5mA
-0.01
0.01
V
1
VI = 41.25V, IL = -50mA
-0.01
0.01
V
1
VRLine
Line Regulation
4.25V ≤ VI ≤ 41.25V,
IL = -5mA
-4.0
4.0
mV
1
IAdj
Adjust Pin Current
VI = 4.25V, IL = -5mA
-10
10
µA
1
VI = 41.25V, IL = -5mA
-10
10
µA
1
VI = 4.25V, RL = 2.5Ω,
CL = 20µf
-0.01
0.01
V
1
VI = 40V, RL = 250Ω
-0.01
0.01
V
1
Min
Max
Unit
Subgroups
VI = 4.25V, IL = -5mA
1.2
1.350
V
1
VI = 4.25V, IL = -500mA
1.2
1.350
V
1
VI = 41.25V, IL = -5mA
1.2
1.350
V
1
VI = 41.25V, IL = -50mA
1.2
1.350
V
1
25
mV
1
dB
4
VO (Recov) Output Voltage Recovery
AC/DC Post Radiation Limits @ +25°C
Symbol
VO
Parameter
Output Voltage
(Note 12, Note 13)
Conditions
Notes
VRLine
Line Regulation
4.25V ≤ VI ≤ 41.25V,
IL = -5mA
-25
ΔVI / ΔVO
Ripple Rejection
VI = 6.25V, IL = -125mA
EI = 1VRMS at f = 2400Hz
60
VO (Recov) Output Voltage Recovery
www.national.com
VI = 4.25V, RL = 2.5Ω,
CL = 20µf
1.20 1.350
V
1
VI = 40V, RL = 250Ω
1.20 1.350
V
1
10
RH Electrical Characteristics
DC Parameters
Symbol
VO
VRLine
VRLoad
LM117QML
LM117K
(Note 12)
Parameter
Conditions
Output Voltage
Line Regulation
Load Regulation
Notes
Min
Max
Unit
Subgroups
VI = 4.25V, IL = -5mA
1.2
1.3
V
1, 2, 3
VI = 4.25V, IL = -1.5A
1.2
1.3
V
1, 2, 3
VI = 41.25V, IL = -5mA
1.2
1.3
V
1, 2, 3
VI = 41.25V, IL = -200mA
1.2
1.3
V
1, 2, 3
4.25V ≤ VI ≤ 41.25V,
IL = -5mA
-9.0
9.0
mV
1
-23
23
mV
2,3
VI = 6.25V,
-3.5
3.5
mV
1
-1.5A ≤ IL ≤ -5mA
-12
12
mV
2, 3
VI = 41.25V,
-3.5
3.5
mV
1
-12
12
mV
2, 3
-200mA ≤ IL ≤ -5mA
VRTh
Thermal Regulation
IAdj
Adjust Pin Current
ΔIAdj/ Line
Adjust Pin Current Change
ΔIAdj / Load Adjust Pin Current Change
IQ
Minimum Load Current
IOS
Output Short Circuit Current
VO (Recov) Output Voltage Recovery
VI = 14.6V, IL = -1.5A
-12
12
mV
1
VI = 4.25V, IL = -5mA
-100
-15
µA
1, 2, 3
VI = 41.25V, IL = -5mA
-100
-15
µA
1, 2, 3
4.25V ≤ VI ≤ 41.25V,
IL = -5mA
-5.0
5.0
µA
1, 2, 3
-5.0
5.0
µA
1, 2, 3
VI = 4.25V,
Forced VO = 1.4V
-3.0
-0.2
mA
1, 2, 3
VI = 14.25V,
Forced VO = 1.4V
-3.0
-0.2
mA
1, 2, 3
VI = 41.25V,
Forced VO = 1.4V
-5.0
-0.2
mA
1, 2, 3
VI = 4.25V
-3.5
-1.5
A
1, 2, 3
VI = 40V
-1.0
-0.18
A
1, 2, 3
VI = 4.25V, RL = 0.833Ω,
CL = 20µF
1.2
1.3
V
1, 2, 3
1.2
1.3
V
1, 2, 3
1.2
1.3
V
2
1.2
1.3
V
1, 2, 3
Min
Max
Unit
Subgroups
120
µVRMS
7
VI = 6.25V,
-1.5A ≤ IL ≤ -5mA
VI = 40V, RL = 250Ω
VO
Output Voltage
VI = 6.25V, IL = -5mA
VStart
Voltage Start-Up
VI = 4.25V, RL = 0.833Ω,
CL = 20µF, IL = -1.5A
AC Parameters
(Note 9)
(Note 12)
Symbol
Parameter
Conditions
Notes
VNO
Output Noise Voltage
VI = 6.25V, IL = -100mA
ΔVO / ΔVI
Line Transient Response
VI = 6.25V, ΔVI = 3V,
IL = -10mA
(Note 10)
18
mV
7
ΔVO / ΔIL
Load Transient Response
VI = 6.25V, ΔIL = -400mA,
IL = -100mA
(Note 11)
120
mV
7
ΔVI / ΔVO
Ripple Rejection
VI = 6.25V, IL = -500mA,
EI = 1VRMS at ƒ = 2400Hz
dB
4
11
65
www.national.com
LM117QML
DC Drift Parameters
The following conditions apply, unless otherwise specified.
Deltas performed on QMLV devices at Group B, Subgroup 5, only.
Symbol
VO
Parameter
Output Voltage
VRLine
Line Regulation
IAdj
Adjust Pin Current
VO (Recov) Output Voltage Recovery
Conditions
Notes
Min
Max
Unit
Subgroups
VI = 4.25V, IL = -5mA
-0.01
0.01
V
1
VI = 4.25V, IL = -1.5A
-0.01
0.01
V
1
VI = 41.25V, IL = -5mA
-0.01
0.01
V
1
VI = 41.25V, IL = -200mA
-0.01
0.01
V
1
4.25V ≤ VI ≤ 41.25V,
IL = -5mA
-4.0
4.0
mV
1
VI = 4.25V, IL = -5mA
-10
10
µA
1
VI = 41.25V, IL = -5mA
-10
10
µA
1
VI = 4.25V, RL = 0.833Ω,
CL = 20µS
-0.01
0.01
V
1
VI = 40V, RL = 250Ω
-0.01
0.01
V
1
Min
Max
Unit
Subgroups
VI = 4.25V, IL = -5mA
1.2
1.350
V
1
VI = 4.25V, IL = -1.5A
1.2
1.350
V
1
VI = 41.25V, IL = -5mA
1.2
1.350
V
1
VI = 41.25V, IL = -200mA
1.2
1.350
V
1
4.25V ≤ VI ≤ 41.25V,
IL = -5mA
-25
25
mV
1
-7.0
7.0
mV
1
-7.0
7.0
mV
1
dB
4
AC/DC Post Radiation Limits @ +25°C
Symbol
VO
VRLine
Parameter
Output Voltage
Line Regulation
(Note 12)
Conditions
Notes
VI = 6.25V,
VRLoad
Load Regulation
-1.5A ≤ IL ≤ -5mA
VI = 41.25V,
-200mA ≤ IL ≤ -5mA
ΔVI / ΔVO
Ripple Rejection
VO (Recov) Output Voltage Recovery
www.national.com
VI = 6.25V, IL = -500mA
EI = 1VRMS at f = 2400Hz
60
VI = 4.25V, RL = 0.833Ω,
CL = 20µS
1.20 1.350
V
1
VI = 40V, RL = 250Ω
1.20 1.350
V
1
12
Note 3: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax (maximum junction temperature), θJA (package
junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any temperature is PDmax = (TJmax - TA)/
θJA or the number given in the Absolute Maximum Ratings, whichever is lower. "Although power dissipation is internally limited, these specifications are applicable
for power dissipations of 2W for the TO39, LCC, and ceramic SOIC packages, and 20W for the TO3 package."
Note 4: Human body model, 100 pF discharged through a 1.5 kΩ resistor.
Note 5: For the Ceramic SOIC device to function properly, the “Output” and “Output/Sense” pins must be connected on the users printed circuit board.
Note 6: The package material for these devices allows much improved heat transfer over our standard ceramic packages. In order to take full advantage of this
improved heat transfer, heat sinking must be provided between the package base (directly beneath the die), and either metal traces on, or thermal vias through,
the printed circuit board. Without this additional heat sinking, device power dissipation must be calculated using θJA, rather than θJC, thermal resistance. It must
not be assumed that the device leads will provide substantial heat transfer out the package, since the thermal resistance of the leadframe material is very poor,
relative to the material of the package base. The stated θJC thermal resistance is for the package material only, and does not account for the additional thermal
resistance between the package base and the printed circuit board. The user must determine the value of the additional thermal resistance and must combine
this with the stated value for the package, to calculate the total allowed power dissipation for the device.
Note 7: Guaranteed parameter, not tested.
Note 8: Tested @ 25°C; guaranteed, but not tested @ 125°C & −55°C
Note 9: Tested @ TA = 125°C, correlated to TA = 150°C
Note 10: SMD limit of 6mV/V is equivalent to 18mV
Note 11: SMD limit of 0.3mV/V is equivalent to 120mV
Note 12: Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics except as listed in the “Post Radiation Limits” table.
These parts may be dose rate sensitive in a space environment and demonstrate enhanced low dose rate effect. Radiation end point limits for the noted parameters
are guaranteed only for the conditions as specified in Mil-Std-883, Method 1019.5, Condition A.
Note 13: Low dose rate testing has been performed on a wafer-by-wafer basis, per test method 1019 condition D of MIL-STD-883, with no enhanced low dose
rate sensitivity (ELDRS) effect.
Typical Performance Characteristics
Output Capacitor = 0μF unless otherwise noted
Load Regulation
Current Limit
20143637
20143638
13
www.national.com
LM117QML
Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed
specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test
conditions.
LM117QML
Adjustment Current
Dropout Voltage
20143640
20143639
Temperature Stability
Minimum Operating Current
20143641
20143642
Ripple Rejection
Ripple Rejection
20143644
20143643
www.national.com
14
LM117QML
Ripple Rejection
Output Impedance
20143646
20143645
Line Transient Response
Load Transient Response
20143647
20143648
15
www.national.com
LM117QML
tween 500 pF and 5000 pF. A 1μF solid tantalum (or 25μF
aluminum electrolytic) on the output swamps this effect and
insures stability. Any increase of the load capacitance larger
than 10μF will merely improve the loop stability and output
impedance.
Application Hints
In operation, the LM117 develops a nominal 1.25V reference
voltage, VREF, between the output and adjustment terminal.
The reference voltage is impressed across program resistor
R1 and, since the voltage is constant, a constant current I1
then flows through the output set resistor R2, giving an output
voltage of
LOAD REGULATION
The LM117 is capable of providing extremely good load regulation but a few precautions are needed to obtain maximum
performance. The current set resistor connected between the
adjustment terminal and the output terminal (usually 240Ω)
should be tied directly to the output (case) of the regulator
rather than near the load. This eliminates line drops from appearing effectively in series with the reference and degrading
regulation. For example, a 15V regulator with 0.05Ω resistance between the regulator and load will have a load regulation due to line resistance of 0.05Ω × IL. If the set resistor is
connected near the load the effective line resistance will be
0.05Ω (1 + R2/R1) or in this case, 11.5 times worse.
Figure 2 shows the effect of resistance between the regulator
and 240Ω set resistor.
20143605
FIGURE 1.
Since the 100μA current from the adjustment terminal represents an error term, the LM117 was designed to minimize
IADJ and make it very constant with line and load changes. To
do this, all quiescent operating current is returned to the output establishing a minimum load current requirement. If there
is insufficient load on the output, the output will rise.
20143606
FIGURE 2. Regulator with Line Resistance in Output Lead
EXTERNAL CAPACITORS
An input bypass capacitor is recommended. A 0.1μF disc or
1μF solid tantalum on the input is suitable input bypassing for
almost all applications. The device is more sensitive to the
absence of input bypassing when adjustment or output capacitors are used but the above values will eliminate the
possibility of problems.
The adjustment terminal can be bypassed to ground on the
LM117 to improve ripple rejection. This bypass capacitor prevents ripple from being amplified as the output voltage is
increased. With a 10μF bypass capacitor 80dB ripple rejection is obtainable at any output level. Increases over 10μF do
not appreciably improve the ripple rejection at frequencies
above 120Hz. If the bypass capacitor is used, it is sometimes
necessary to include protection diodes to prevent the capacitor from discharging through internal low current paths and
damaging the device.
In general, the best type of capacitors to use is solid tantalum.
Solid tantalum capacitors have low impedance even at high
frequencies. Depending upon capacitor construction, it takes
about 25μF in aluminum electrolytic to equal 1μF solid tantalum at high frequencies. Ceramic capacitors are also good at
high frequencies; but some types have a large decrease in
capacitance at frequencies around 0.5MHz. For this reason,
0.01μF disc may seem to work better than a 0.1μF disc as a
bypass.
Although the LM117 is stable with no output capacitors, like
any feedback circuit, certain values of external capacitance
can cause excessive ringing. This occurs with values bewww.national.com
With the TO-3 package, it is easy to minimize the resistance
from the case to the set resistor, by using two separate leads
to the case. However, with the TO-39 package, care should
be taken to minimize the wire length of the output lead. The
ground of R2 can be returned near the ground of the load to
provide remote ground sensing and improve load regulation.
PROTECTION DIODES
When external capacitors are used with any IC regulator it is
sometimes necessary to add protection diodes to prevent the
capacitors from discharging through low current points into
the regulator. Most 10μF capacitors have low enough internal
series resistance to deliver 20A spikes when shorted. Although the surge is short, there is enough energy to damage
parts of the IC.
When an output capacitor is connected to a regulator and the
input is shorted, the output capacitor will discharge into the
output of the regulator. The discharge current depends on the
value of the capacitor, the output voltage of the regulator, and
the rate of decrease of VIN. In the LM117, this discharge path
is through a large junction that is able to sustain 15A surge
with no problem. This is not true of other types of positive
regulators. For output capacitors of 25μF or less, there is no
need to use diodes.
The bypass capacitor on the adjustment terminal can discharge through a low current junction. Discharge occurs when
either the input or output is shorted. Internal to the LM117 is
a 50Ω resistor which limits the peak discharge current. No
protection is needed for output voltages of 25V or less and
16
θ(H−A) is specified numerically by the heatsink manufacturer
in the catalog, or shown in a curve that plots temperature rise
vs power dissipation for the heatsink.
20143607
D1 protects against C1
D2 protects against C2
FIGURE 3. Regulator with Protection Diodes
Typical Applications
5V Logic Regulator with Electronic Shutdown*
Slow Turn-On 15V Regulator
20143609
20143603
*Min. output ≊ 1.2V
Adjustable Regulator with Improved Ripple Rejection
20143610
†Solid tantalum
*Discharges C1 if output is shorted to ground
17
www.national.com
LM117QML
When a value for θ(H−A) is found using the equation shown, a
heatsink must be selected that has a value that is less than
or equal to this number.
10μF capacitance. Figure 3 shows an LM117 with protection
diodes included for use with outputs greater than 25V and
high values of output capacitance.
LM117QML
High Stability 10V Regulator
20143611
High Current Adjustable Regulator
20143612
‡Optional—improves ripple rejection
†Solid tantalum
*Minimum load current = 30 mA
www.national.com
18
LM117QML
0 to 30V Regulator
Power Follower
20143613
20143614
Full output current not available at high input-output voltages
5A Constant Voltage/Constant Current Regulator
20143615
†Solid tantalum
*Lights in constant current mode
19
www.national.com
LM117QML
1A Current Regulator
20143616
1.2V–20V Regulator with Minimum Program Current
20143617
*Minimum load current ≊ 4 mA
High Gain Amplifier
20143618
www.national.com
20
LM117QML
Low Cost 3A Switching Regulator
20143619
†Solid tantalum
*Core—Arnold A-254168-2 60 turns
4A Switching Regulator with Overload Protection
20143620
†Solid tantalum
*Core—Arnold A-254168-2 60 turns
Precision Current Limiter
20143621
21
www.national.com
LM117QML
Tracking Preregulator
20143622
Current Limited Voltage Regulator
20143623
(Compared to LM117's higher current limit)
—At 50 mA output only ¾ volt of drop occurs in R3 and R4
Adjusting Multiple On-Card Regulators with Single Control*
20143624
*All outputs within ±100 mV
†Minimum load—10 mA
www.national.com
22
LM117QML
AC Voltage Regulator
20143625
12V Battery Charger
20143626
Use of RS allows low charging rates with fully charged battery.
50mA Constant Current Battery Charger
20143627
23
www.national.com
LM117QML
Current Limited 6V Charger
Adjustable 4A Regulator
20143629
*Sets peak current (0.6A for 1Ω)
**The 1000μF is recommended to filter out input transients
Digitally Selected Outputs
20143628
1.2V–25V Adjustable Regulator
20143602
*Sets maximum VOUT
20143601
Full output current not available at high input-output voltages
*Needed if device is more than 6 inches from filter capacitors.
†Optional—improves transient response. Output capacitors in the range
of 1μF to 1000μF of aluminum or tantalum electrolytic are commonly used
to provide improved output impedance and rejection of transients.
www.national.com
24
Date Released
Revision
03/17/06
A
Section
Changes
New Release to corporate format
5 MDS data sheets were consolidated into one
corporate data sheet format. Clarified ΔIAdj/ Line
versus ΔIAdj/ Load by separating the parameters in
all of the tables. MNLM117–K Rev 1C1,
MNLM117–X Rev 0A0, MNLM117–E Rev 0B1,
MRLM117–X-RH Rev 2A0, MRLM117–K-RH Rev
3A0 will be archived.
06/29/06
B
Features, Ordering Information Table, Rad Deleted NSID LM117WGRQML, no longer
Hard Electrical Section for H and WG
available. Added Available with Radiation
packages and Notes
Guarantee, Low Dose NSID's to table
5962R9951705VXA LM117HRLQMLV,
5962R9951705VZA LM117WGRLQMLV, and
reference to Note 11 and 12. Note 12 to Rad Hard
Electrical Heading for H and WG packages. Note
12 to Notes. Archive Revision A.
11/30/2010
C
Features, Ordering Table, Absolute
Ratings, LM117H, WG and K RH Drift
Electrical Table
Added radiation info., Update with current device
information and format, T0–39 Pkg weight, Vo
(Recov). Revision B will be Archived.
09/06/2011
D
Ordering Information, Absolute Ratings
Order Info: Added 'GW' NSIDS and SMD numbers.
Abs Max Ratings: Added 'GW' Theta JA and Theta
JC along with 'GW' weight. Revision C will be
Archived.
25
www.national.com
LM117QML
Revision History
LM117QML
Physical Dimensions inches (millimeters) unless otherwise noted
(TO-39) Metal Can Package
NS Package Number H03A
TO-3 Metal Can Package (K)
NS Package Number K02C
www.national.com
26
LM117QML
Ceramic Leadless Chip Carrier
NS Package Number E20A
Ceramic SOIC
NS Package Number WG16A
27
www.national.com
LM117QML 3-Terminal Adjustable Regulator
Notes
For more National Semiconductor product information and proven design tools, visit the following Web sites at:
www.national.com
Products
Design Support
Amplifiers
www.national.com/amplifiers
WEBENCH® Tools
www.national.com/webench
Audio
www.national.com/audio
App Notes
www.national.com/appnotes
Clock and Timing
www.national.com/timing
Reference Designs
www.national.com/refdesigns
Data Converters
www.national.com/adc
Samples
www.national.com/samples
Interface
www.national.com/interface
Eval Boards
www.national.com/evalboards
LVDS
www.national.com/lvds
Packaging
www.national.com/packaging
Power Management
www.national.com/power
Green Compliance
www.national.com/quality/green
Switching Regulators
www.national.com/switchers
Distributors
www.national.com/contacts
LDOs
www.national.com/ldo
Quality and Reliability
www.national.com/quality
LED Lighting
www.national.com/led
Feedback/Support
www.national.com/feedback
Voltage References
www.national.com/vref
Design Made Easy
www.national.com/easy
www.national.com/powerwise
Applications & Markets
www.national.com/solutions
Mil/Aero
www.national.com/milaero
PowerWise® Solutions
Serial Digital Interface (SDI) www.national.com/sdi
Temperature Sensors
www.national.com/tempsensors SolarMagic™
www.national.com/solarmagic
PLL/VCO
www.national.com/wireless
www.national.com/training
PowerWise® Design
University
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION
(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY
OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO
SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,
IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT.
TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT
NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL
PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR
APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND
APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE
NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.
EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO
LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE
AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY
RIGHT.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and
whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform
can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other
brand or product names may be trademarks or registered trademarks of their respective holders.
Copyright© 2011 National Semiconductor Corporation
For the most current product information visit us at www.national.com
National Semiconductor
Americas Technical
Support Center
Email: [email protected]
Tel: 1-800-272-9959
www.national.com
National Semiconductor Europe
Technical Support Center
Email: [email protected]
National Semiconductor Asia
Pacific Technical Support Center
Email: [email protected]
National Semiconductor Japan
Technical Support Center
Email: [email protected]
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and Automotive www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
www.ti.com/video
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
Similar pages