TI1 LM150QML 3-amp adjustable regulator Datasheet

OBSOLETE
LM150QML
www.ti.com
SNVS383B – MARCH 2006 – REVISED APRIL 2013
LM150QML 3-Amp Adjustable Regulators
Check for Samples: LM150QML
FEATURES
DESCRIPTION
•
•
•
•
•
•
The LM150 adjustable 3-terminal positive voltage
regulator is capable of supplying in excess of 3A over
a 1.2V to 33V output range. It is exceptionally easy to
use and requires only 2 external resistors to set the
output voltage. Further, both line and load regulation
are comparable to discrete designs. Also, the LM150
is packaged in standard transistor package which is
easily mounted and handled.
1
2
Adjustable Output Down to 1.2V
Ensured 3A Output Current
Ensured Thermal Regulation
Output is Short Circuit Protected
Current Limit Constant with Temperature
86 dB Ripple Rejection
APPLICATIONS
•
•
•
Adjustable Power Supplies
Constant Current Regulators
Battery Chargers
In addition to higher performance than fixed
regulators, the LM150 offers full overload protection
available only in IC's. Included on the chip are current
limit, thermal overload protection and safe area
protection. All overload protection circuitry remains
fully functional even if the adjustment terminal is
accidentally disconnected.
Normally, no capacitors are needed unless the device
is situated more than 6 inches from the input filter
capacitors in which case an input bypass is needed.
An output capacitor can be added to improve
transient response, while bypassing the adjustment
pin will increase the regulator's ripple rejection.
Besides replacing fixed regulators or discrete
designs, the LM150 is useful in a wide variety of
other applications. Since the regulator is “floating”
and sees only the input-to-output differential voltage,
supplies of several hundred volts can be regulated as
long as the maximum input to output differential is not
exceeded, i.e., avoid short-circuiting the output.
By connecting a fixed resistor between the
adjustment pin and output, the LM150 can be used
as a precision current regulator. Supplies with
electronic shutdown can be achieved by clamping the
adjustment terminal to ground which programs the
output to 1.2V where most loads draw little current.
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006–2013, Texas Instruments Incorporated
OBSOLETE
LM150QML
SNVS383B – MARCH 2006 – REVISED APRIL 2013
www.ti.com
Connection Diagram
ADJUSTMENT
VIN
Case is Output
Bottom View
TO-3 Metal Can Package
See Package Number K02C
Schematic Diagram
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
2
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM150QML
OBSOLETE
LM150QML
www.ti.com
SNVS383B – MARCH 2006 – REVISED APRIL 2013
Absolute Maximum Ratings (1)
Power Dissipation (2)
Internally Limited
Input-Output Voltage Differential
+35V
−65°C ≤ TA ≤ +150°C
Storage Temperature
Lead Temperature (Soldering, 10 sec.)
300°C
ESD Tolerance
TBD
−55°C ≤ TA ≤ +125°C
Operating Temperature Range
(1)
(2)
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the
Electrical Characteristics. The specified specifications apply only for the test conditions listed. Some performance characteristics may
degrade when the device is not operated under the listed test conditions.
The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax (maximum junction temperature),
θJA (package junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any
temperature is PDmax = (TJmax - TA)/θJA or the number given in the Absolute Maximum Ratings, whichever is lower.
Quality Conformance Inspection
Mil-Std-883, Method 5005 - Group A
Subgroup
Description
Temp °C
1
Static tests at
25
2
Static tests at
125
3
Static tests at
-55
4
Dynamic tests at
25
5
Dynamic tests at
125
6
Dynamic tests at
-55
7
Functional tests at
25
8A
Functional tests at
125
8B
Functional tests at
-55
9
Switching tests at
25
10
Switching tests at
125
11
Switching tests at
-55
12
Settling time at
25
13
Settling time at
125
14
Settling time at
-55
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM150QML
3
OBSOLETE
LM150QML
SNVS383B – MARCH 2006 – REVISED APRIL 2013
www.ti.com
LM150 Electrical Characteristics DC Parameters
The following conditions apply, unless otherwise specified.
DC: VDiff = 5V, VO = VRef, IO = 1.5A.
Symbol
Parameter
Conditions
Notes
VRef
Reference Voltage
VLoad
1.3
V
1, 2, 3
1.3
V
1, 2, 3
VDiff = 3.0V, IL = 3.0A
1.2
1.3
V
1, 2, 3
VDiff = 35V, IL = 10mA
1.2
1.3
V
1, 2, 3
1.2
1.3
V
1, 2, 3
1.2
1.3
V
1, 2, 3
-3.8
3.8
mV
1
2, 3
3V ≤ VDiff ≤ 35V, ILoad = 10mA
VDiff = 30V, 10mA ≤ IL ≤ 300mA
10mA ≤ IL ≤ 3A, VO = 5.0V
TReg
Thermal Regulation
IAdj
Adjust Pin Current
IQ
Quiescent Current
ΔIAdj
Delta Adjustment Current
Current Limit
t = 20mS
See
(1)
See (2) (3)
See
(2) (3)
-19.0
19.0
mV
See (3) (4) (5)
-3.6
3.6
mV
1
See (3) (4) (5)
-12.0
12.0
mV
2, 3
See (3)
-2.0
2.0
mV
1
See (3)
-5.0
5.0
mV
2, 3
See (3) (4) (6)
-15.0
15.0
mV
1
See (3) (4) (6)
-50.0
50.0
mV
2, 3
See (7)
-9.75
9.75
mV
1
100
µA
1, 2, 3
100
µA
1, 2, 3
5.0
mA
1, 2, 3
5.0
mA
1, 2, 3
VDiff = 35V, IO = 10mA
VDiff = 35V
3V ≤ VDiff ≤ 35V IO = 10mA
-5.0
5.0
µA
1, 2, 3
10mA ≤ IL ≤ 3A
-5.0
5.0
µA
1, 2, 3
VDiff = 30V, 10mA ≤ IL ≤ 300mA
-5.0
5.0
µA
1, 2, 3
VDiff = 10V
3.0
A
1, 2, 3
VDiff = 30V
0.3
A
1, 2, 3
1.0
%/VO
2
100
mV
1, 2, 3
ΔVO / Δt
Long Term Stability
TA = +125°C, t = 1000 Hrs,
VDiff = 3.0V, IL = 10mA
VDrop
Voltage Dropout
VDiff = 2.9V, IL = 3A
(1)
(2)
(3)
Subgroups
1.2
10mA ≤ IL ≤ 3A, VO = VRef
Load Regulation
Unit
1.2
VDiff = 30V, IL = 300mA
Line Regulation
Max
VDiff = 3.0V, IL = 10mA
VDiff = 10V, IL = 3.0A
VLine
Min
See (8)
-100
Represents worst case power dissipation of 30W.
Limits = 0.01% of VO @ 25°C, 0.05% @ −55°C, +125°C per volt of VDiff change at VO = VRef.
Regulation is measured at a constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to
heating effects are covered under the specifications for thermal regulation.
These VO conditions are worst case
Limits are equivalent to 15mV @ 25°C and 50mV @ −55°C, +125°C @ VO = 5.0V.
Limits = 0.3% of VO @ 25°C, 1.0% @ −55°C, +125°C @ VO = 5.0V.
Limits = 0.01% of VO @ 25°C per Watt of power dissipation at PD = 7.5W.
Periodic Group C testing.
(4)
(5)
(6)
(7)
(8)
LM150 Electrical Characteristics AC Parameters
Symbol
RR
4
Parameter
Ripple Rejection
Conditions
ƒ = 120 Hz, eI = 1VRMS,
CAdj = 10µF, VO = 10V
Submit Documentation Feedback
Notes
Min
66
Max
Unit
Subgroups
dB
4, 5, 6
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM150QML
OBSOLETE
LM150QML
www.ti.com
SNVS383B – MARCH 2006 – REVISED APRIL 2013
Typical Performance Characteristics
Load Regulation
Current Limit
Figure 1.
Figure 2.
Adjustment Current
Dropout Voltage
Figure 3.
Figure 4.
Temperature Stability
Minimum Operating Current
Figure 5.
Figure 6.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM150QML
5
OBSOLETE
LM150QML
SNVS383B – MARCH 2006 – REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics (continued)
6
Ripple Rejection
Ripple Rejection
Figure 7.
Figure 8.
Ripple Rejection
Output Impedance
Figure 9.
Figure 10.
Line Transient Response
Load Transient Response
Figure 11.
Figure 12.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM150QML
OBSOLETE
LM150QML
www.ti.com
SNVS383B – MARCH 2006 – REVISED APRIL 2013
APPLICATION HINTS
In operation, the LM150 develops a nominal 1.25V reference voltage, VRef, between the output and adjustment
terminal. The reference voltage is impressed across program resistor R1 and, since the voltage is constant, a
constant current I1 then flows through the output set resistor R2, giving an output voltage of
(1)
Since the 50 μA current from the adjustment terminal represents an error term, the LM150 was designed to
minimize IAdj and make it very constant with line and load changes. To do this, all quiescent operating current is
returned to the output establishing a minimum load current requirement. If there is insufficient load on the output,
the output will rise.
EXTERNAL CAPACITORS
An input bypass capacitor is recommended. A 0.1 μF disc or 1 μF solid tantalum on the input is suitable input
bypassing for almost all applications. The device is more sensitive to the absence of input bypassing when
adjustment or output capacitors are used but the above values will eliminate the possibility of problems.
The adjustment terminal can be bypassed to ground on the LM150 to improve ripple rejection. This bypass
capacitor prevents ripple from being amplified as the output voltage is increased. With a 10 μF bypass capacitor
86 dB ripple rejection is obtainable at any output level. Increases over 10 μF do not appreciably improve the
ripple rejection at frequencies above 120 Hz. If the bypass capacitor is used, it is sometimes necessary to
include protection diodes to prevent the capacitor from discharging through internal low current paths and
damaging the device.
In general, the best type of capacitors to use is solid tantalum. Solid tantalum capacitors have low impedance
even at high frequencies. Depending upon capacitor construction, it takes about 25 μF in aluminum electrolytic to
equal 1 μF solid tantalum at high frequencies. Ceramic capacitors are also good at high frequencies, but some
types have a large decrease in capacitance at frequencies around 0.5 MHz. For this reason, 0.01 μF disc may
seem to work better than a 0.1 μF disc as a bypass.
Although the LM150 is stable with no output capacitors, like any feedback circuit, certain values of external
capacitance can cause excessive ringing. This occurs with values between 500 pF and 5000 pF. A 1 μF solid
tantalum (or 25 μF aluminum electrolytic) on the output swamps this effect and insures stability.
LOAD REGULATION
The LM150 is capable of providing extremely good load regulation but a few precautions are needed to obtain
maximum performance. The current set resistor connected between the adjustment terminal and the output
terminal (usually 240Ω) should be tied directly to the output (case) of the regulator rather than near the load. This
eliminates line drops from appearing effectively in series with the reference and degrading regulation. For
example, a 15V regulator with 0.05Ω resistance between the regulator and load will have a load regulation due to
line resistance of 0.05Ω × IOUT. If the set resistor is connected near the load the effective line resistance will be
0.05Ω (1 + R2/R1) or in this case, 11.5 times worse.
Figure 13 shows the effect of resistance between the regulator and 240Ω set resistor.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM150QML
7
OBSOLETE
LM150QML
SNVS383B – MARCH 2006 – REVISED APRIL 2013
www.ti.com
Figure 13. Regulator with Line Resistance
in Output Lead
With the TO-3 package, it is easy to minimize the resistance from the case to the set resistor, by using two
separate leads to the case. The ground of R2 can be returned near the ground of the load to provide remote
ground sensing and improve load regulation.
PROTECTION DIODES
When external capacitors are used with any IC regulator it is sometimes necessary to add protection diodes to
prevent the capacitors from discharging through low current points into the regulator. Most 10 μF capacitors have
low enough internal series resistance to deliver 20A spikes when shorted. Although the surge is short, there is
enough energy to damage parts of the IC.
When an output capacitor is connected to a regulator and the input is shorted, the output capacitor will discharge
into the output of the regulator. The discharge current depends on the value of the capacitor, the output voltage
of the regulator, and the rate of decrease of VIN. In the LM150, this discharge path is through a large junction that
is able to sustain 25A surge with no problem. This is not true of other types of positive regulators. For output
capacitors of 25 μF or less, there is no need to use diodes.
The bypass capacitor on the adjustment terminal can discharge through a low current junction. Discharge occurs
when either the input or output is shorted. Internal to the LM150 is a 50Ω resistor which limits the peak discharge
current. No protection is needed for output voltages of 25V or less and 10 μF capacitance. Figure 14 shows an
LM150 with protection diodes included for use with outputs greater than 25V and high values of output
capacitance.
D1 protects against C1
D2 protects against C2
Figure 14. Regulator with Protection Diodes
8
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM150QML
OBSOLETE
LM150QML
www.ti.com
SNVS383B – MARCH 2006 – REVISED APRIL 2013
Typical Applications
Full output current not available
at high input-output voltages.
†Optional—improves transient response. Output capacitors in the range of 1 μF to 1000 μF of aluminum or tantalum
electrolytic are commonly used to provide improved output impedance and rejection of transients.
*Needed if device is more than 6 inches from filter capacitors.
Note: Usually R1 = 240Ω for LM150 and R1 = 120Ω.
Figure 15. 1.2V–25V Adjustable Regulator
*Adjust for 3.75V across R1
Figure 16. Precision Power Regulator with Low Temperature Coefficient
Figure 17. Slow Turn-ON 15V Regulator
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM150QML
9
OBSOLETE
LM150QML
SNVS383B – MARCH 2006 – REVISED APRIL 2013
www.ti.com
†Solid tantalum
*Discharges C1 if output is shorted to ground
Figure 18. Adjustable Regulator with Improved
Ripple Rejection
Figure 19. High Stability 10V Regulator
*Sets maximum VO
Figure 20. Digitally Selected Outputs
10
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM150QML
OBSOLETE
LM150QML
www.ti.com
SNVS383B – MARCH 2006 – REVISED APRIL 2013
Figure 21. Regulator and Voltage Reference
*Minimum load current 50 mA
Figure 22. 10A Regulator
*Minimum output ≈ 1.2V
Figure 23. 5V Logic Regulator with
Electronic Shutdown*
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM150QML
11
OBSOLETE
LM150QML
SNVS383B – MARCH 2006 – REVISED APRIL 2013
www.ti.com
Full output current not available at high input-output voltages
Figure 24. 0 to 30V Regulator
†Solid tantalum
*Lights in constant current mode
Figure 25. 5A Constant Voltage/Constant Current Regulator
12
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM150QML
OBSOLETE
LM150QML
www.ti.com
SNVS383B – MARCH 2006 – REVISED APRIL 2013
Figure 26. 12V Battery Charger
*0.4 ≤ R1 ≤ 120Ω
Figure 27. Adjustable Current Regulator
Figure 28. Precision Current Limiter
*Minimum output current ≈ 4 mA
Figure 29. .2V–20V Regulator with
Minimum Program Current
Figure 30. 3A Current Regulator
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM150QML
13
OBSOLETE
LM150QML
SNVS383B – MARCH 2006 – REVISED APRIL 2013
www.ti.com
Figure 31. Tracking Preregulator
†Minimum load—10 mA
*All outputs within ±100 mV
Figure 32. Adjusting Multiple On-Card Regulators
with Single Control*
Use of RS allows low charging rates with fully charged battery.
**1000 μF is recommended to filter out any input transients
Figure 33. AC Voltage Regulator
14
Figure 34. Simple 12V Battery Charger
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM150QML
OBSOLETE
LM150QML
www.ti.com
SNVS383B – MARCH 2006 – REVISED APRIL 2013
Figure 35. Simple 12V Battery Charger
Figure 36. Light Controller
*Sets peak current (2A for 0.3Ω)
**1000 μF is recommended to filter out any input transients.
Figure 37. Adjustable 10A Regulator
Figure 38. Current Limited 6V Charger
Figure 39. 6A Regulator
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM150QML
15
OBSOLETE
LM150QML
SNVS383B – MARCH 2006 – REVISED APRIL 2013
www.ti.com
REVISION HISTORY
Released
Revision
Section
Changes
03/10/06
A
New Release, Corporate format
1 MDS data sheet converted into one Corp. data
sheet format. MNLM150-X Rev. 0BL will be archived.
09/27/2010
B
Obsolete Data Sheet
End Of Life on Product/NSID Dec. 2009
Changes from Revision A (April 2013) to Revision B
•
16
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 15
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM150QML
PACKAGE OPTION ADDENDUM
www.ti.com
26-Jul-2016
PACKAGING INFORMATION
Orderable Device
Status
(1)
LM150G MD8
ACTIVE
Package Type Package Pins Package
Drawing
Qty
DIESALE
Y
0
100
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Green (RoHS
& no Sb/Br)
Call TI
Level-1-NA-UNLIM
Op Temp (°C)
Device Marking
(4/5)
-55 to 125
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
26-Jul-2016
Addendum-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated
Similar pages