TI1 LM27 Lm27 sot-23, â±3â°c accurate, 120â°c-150â°c factory preset thermostat Datasheet

LM27
www.ti.com
SNIS124D – AUGUST 2002 – REVISED JULY 2013
LM27 SOT-23, ±3°C Accurate, 120°C-150°C Factory Preset Thermostat
Check for Samples: LM27
FEATURES
DESCRIPTION
•
The LM27 is a precision, single digital-output, lowpower thermostat comprised of an internal reference,
DAC, temperature sensor and comparator. Utilizing
factory programming, it can be manufactured with
different trip points as well as different digital output
functionality. The trip point (TOS) can be preset at the
factory to any temperature in the range of +120°C to
+150°C in 1°C increments. The LM27 has one digital
output (OS/OS/US/US), one digital input (HYST) and
one analog output (VTEMP). The digital output stage
can be preset as either open-drain or push-pull. In
addition, it can be factory programmed to be active
HIGH or LOW. The digital output can be factory
programmed to indicate an over temperature
shutdown event (OS or OS) or an under temperature
shutdown event (US or US). When preset as an
overtemperature shutdown (OS) it will go LOW to
indicate that the die temperature is over the internally
preset TOS and go HIGH when the temperature goes
below (TOS–THYST). Similarly, when preprogrammed
as an undertemperature shutdown (US) it will go
HIGH to indicate that the temperature is below TUS
and go LOW when the temperature is above
(TUS+THYST). The typical hysteresis, THYST, can be set
to 2°C or 10°C and is controlled by the state of the
HYST pin. A VTEMP analog output provides a voltage
that is proportional to temperature and has a
−10.7mV/°C output slope.
1
2
•
•
•
•
•
•
•
Internal Comparator with Pin Selectable 2°C or
10°C Hysteresis
No External Components Required
Open-drain or Push-pull Digital Output;
Supports CMOS Logic Levels
Internal Temperature Sensor with VTEMP Output
Pin
VTEMP Output Allows After-assembly System
Testing
Internal Voltage Reference and DAC for Trippoint Setting
Currently Available in 5-pin SOT-23 Plastic
Package
Excellent Power Supply Noise Rejection
APPLICATIONS
•
•
•
•
•
•
•
Microprocessor Thermal Management
Appliances
Portable Battery Powered Systems
Fan Control
Industrial Process Control
HVAC Systems
Electronic System Protection
KEY SPECIFICATIONS
•
•
•
•
Power Supply Voltage 2.7V to 5.5V
Power Supply Current 40μA (Max), 15μA (Typ)
Hysteresis Temperature 2°C or 10°C (Typ)
Temperature Trip Point Accuracy ±3°C (Max)
Currently, there are several standard parts available,
see Table 1. For other part options, contact a Texas
Instruments Distributor or Sales Representative for
information on minimum order qualification. The
LM27 is currently available in a 5-lead SOT-23
package.
Simplified Block Diagram and Connection Diagram LM27CIM5-2HJ (140°C Trip-Point)
TOS
HYST
OS
HYST
REF
GND
TEMP
SENSOR
TOS- THYST
Temp. of
Leads
+
OS
VTEMP
LM27-2HJ
V+=2.7V
to 5.5V
HYST=GND for 10oC Hysteresis
HYST=V+ for 2oC Hysteresis
VTEMP=(-3.552x10-6x(T-30)2)+(-10.69576x10-3x(T-30))+1.8386V
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2002–2013, Texas Instruments Incorporated
LM27
SNIS124D – AUGUST 2002 – REVISED JULY 2013
www.ti.com
Table 1. Summary Table of Trip Point and Output Function Capabilities of Released Parts (1)
Orderable Device
Trip Point Temperature (°C)
Digital Output Function
LM27CIM5-ZHJ
120
Active-Low, Open-Drain, OS output
LM27CIM5-1HJ
130
Active-Low, Open-Drain, OS output
LM27CIM5-2HJ
140
Active-Low, Open-Drain, OS output
(1)
Other device options have not been released to market, contact Texas Instruments for volume and other requirements for release.
Connection Diagram
HYST
GND
VTEMP
1
2
5
OS, OS, US
or US
LM27
3
4
V+
PIN DESCRIPTIONS
(1)
Pin Number
Pin Name
1
HYST
Hysteresis control, digital input
Function
GND for 10°C or V+ for 2°C
Connection
2
GND
Ground, connected to the back side of
the die through lead frame.
System GND
3
VTEMP
Analog output voltage proportional to
temperature
Leave floating or connect to a high impedance node.
4
V+
Supply input
2.7V to 5.5V with a 0.1µF bypass capacitor. For PSRR
information see NOISE CONSIDERATIONS.
5 (1)
OS
Overtemperature Shutdown open-drain Controller interrupt, system or power supply shutdown;
active low thermostat digital output
pull-up resistor ≥ 10kΩ
OS
Overtemperature Shutdown totem-pull
active high thermostat digital output
Controller interrupt, system or power supply shutdown
US
Undertemperature Shutdown opendrain active low thermostat digital
output
System or power supply shutdown; pull-up resistor ≥ 10kΩ
US
Undertemperature Shutdown totempull active high thermostat digital
output
System or power supply shutdown
Pin 5 functionality and trip point setting are programmed during LM27 manufacture.
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
2
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM27
LM27
www.ti.com
SNIS124D – AUGUST 2002 – REVISED JULY 2013
Absolute Maximum Ratings (1)
Input Voltage
6.0V
Input Current at any pin (2)
5mA
Package Input Current (2)
20mA
Package Dissipation at TA = 25°C (3)
Soldering Information (4)
500mW
Vapor Phase (60 seconds)
SOT23 Package
(1)
(2)
(3)
(4)
(5)
220°C
−65°C to + 150°C
Storage Temperature
ESD Susceptibility (5)
215°C
Infrared (15 seconds)
Human Body Model
2500V
Machine Model
250V
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the
Electrical Characteristics. The specified specifications apply only for the test conditions listed. Some performance characteristics may
degrade when the device is not operated under the listed test conditions.
When the input voltage (VI) at any pin exceeds the power supply (VI < GND or VI > V+), the current at that pin should be limited to 5mA.
The 20mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input
current of 5mA to four. Under normal operating conditions the maximum current that pins 2, 4 or 5 can handle is limited to 5mA each.
The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax (maximum junction temperature),
θJA (junction to ambient thermal resistance) and TA (ambient temperature). The maximum allowable power dissipation at any
temperature is PD = (TJmax–TA)/θJA or the number given in the Absolute Maximum Ratings, whichever is lower. For this device,
TJmax = 150°C. For this device the typical thermal resistance (θJA) of the different package types when board mounted refer to Table 2
See http://www.ti.com/packaging for other recommendations and methods of soldering surface mount devices.
The human body model is a 100pF capacitor discharge through a 1.5kΩ resistor into each pin. The machine model is a 200pF capacitor
discharged directly into each pin.
Table 2.
Package Type
θJA
SOT23-5, DBV
250°C/W
Operating Ratings (1)
TMIN ≤ TA ≤ TMAX
Specified Temperature Range
−40°C ≤ TA ≤ +150°C
LM27CIM
Positive Supply Voltage (V+)
+2.7V to +5.5V
Maximum VOUT
(1)
+5.5V
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the
Electrical Characteristics. The specified specifications apply only for the test conditions listed. Some performance characteristics may
degrade when the device is not operated under the listed test conditions.
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM27
3
LM27
SNIS124D – AUGUST 2002 – REVISED JULY 2013
www.ti.com
LM27 Electrical Characteristics
The following specifications apply for V+ = 2.7VDC to 5.5VDC, and VTEMP load current = 0µA unless otherwise specified.
Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = 25°C unless otherwise specified.
Parameter
Symbol
Conditions
Typical (1)
LM27CIM
Limits (2)
Units
(Limits)
±3
°C (max)
Temperature Sensor
Trip Point Accuracy (Includes VREF, DAC,
Comparator Offset, and Temperature
Sensitivity errors)
+120°C<TA<+150°C
Trip Point Hysteresis
HYST = GND
10
HYST = V+
2
°C
−10.82
mV/°C
VTEMP Output Temperature Sensitivity
−30°C ≤ TA ≤ 150°C, 2.7V ≤
V+ ≤ 5.5V
±3
°C (max)
VO = (−3.552×10−6×(T−30)2+
−55°C ≤ TA ≤ 150°C, 4.5V ≤
(−10.695×10−3×(T−30))+ 1.8386V (1) V+ ≤ 5.5V
±3
°C (max)
±2.5
°C (max)
0.7
mV (max)
VTEMP Temperature Sensitivity Error to
Equation:
TA = 25°C
Source ≤ 1 μA
VTEMP Load Regulation
0.070
Sink ≤ 40 μA
+2.7V ≤ V+ ≤ +5.5V,
−30°C ≤ TA ≤ +120°C
VTEMP Line Regulation
IS
°C
Supply Current
mV
−0.2
15
mV/V
22
40
µA (max)
µA (max)
Digital Output and Input
(1)
(2)
(3)
(4)
4
IOUT(“1”)
Logical “1” Output Leakage Current (3)
V+ = +5.0V
VOUT(“0”)
Logical “0” Output Voltage
IOUT = +1.2mA and
V+≥2.7V; IOUT = +3.2mA
and V+≥4.5V (4)
VOUT(“1”)
Logical “1” Push-Pull Output Voltage
0.001
1
µA (max)
0.4
V (max)
ISOURCE = 500µA, V+ ≥ 2.7V
0.8 × V+
V (min)
ISOURCE = 800µA, V+≥4.5V
V+ − 1.5
V (min)
+
VIH
HYST Input Logical ”1“ Threshold Voltage
0.8 × V
V (min)
VIL
HYST Input Logical ”0“ Threshold Voltage
0.2 × V+
V (max)
Typicals are at TJ = TA = 25°C and represent most likely parametric norm.
Limits are ensured to AOQL (Average Outgoing Quality Level).
The 1µA limit is based on a testing limitation and does not reflect the actual performance of the part. Expect to see a doubling of the
current for every 15°C increase in temperature. For example, the 1nA typical current at 25°C would increase to 16nA at 85°C.
Care should be taken to include the effects of self heating when setting the maximum output load current. The power dissipation of the
LM27 would increase by 1.28mW when IOUT=3.2mA and VOUT=0.4V. With a thermal resistance of 250°C/W, this power dissipation
would cause an increase in the die temperature of about 0.32°C due to self heating. Self heating is not included in the trip point
accuracy specification.
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM27
LM27
www.ti.com
SNIS124D – AUGUST 2002 – REVISED JULY 2013
Part Number Template
The series of digits labeled xyz in the part number LM27CIM-xyz, describe the set point value and the function of
the output as follows:
The place holders xy describe the set point temperature as shown in the following table.
x (10x)
y (1x)
Temperature (°C)
-
H
0
-
J
1
-
K
2
-
L
3
-
N
4
-
P
5
-
R
6
-
S
7
-
T
8
-
V
9
Z
-
12
1
-
13
2
-
14
3
-
15
The value of z describes the assignment/function of the output as shown in the following table:
Active-Low/High
Open-Drain/ PushPull
OS/US
0
0
0
J
Active-Low, Open-Drain, OS output
0
0
1
K
Active-Low, Open-Drain, US output
1
1
0
L
Active-High, Push-Pull, OS output
1
1
1
N
Active-High, Push-Pull, US output
Value of z
Digital Output Function
For example:
• the part number LM27CIM5-2SJ has TOS = 147°C, and programmed as an active-low open-drain
overtemperature shutdown output.
• the part number LM27CIM5-ZLN has TUS = 123°C, and programmed as an active-high, push-pull
undertemperature shutdown output.
Active-high open-drain and active-low push-pull options are available, please contact Texas Instruments for more
information.
Note: Currently, there are several standard parts available, see Table 1. For other part options, contact a Texas
Instruments Distributor or Sales Representative for information on minimum order qualification
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM27
5
LM27
SNIS124D – AUGUST 2002 – REVISED JULY 2013
www.ti.com
FUNCTIONAL DESCRIPTION
LM27 OPTIONS — Output Pin Options Block Diagrams
HYST
HYST
OS
US
HYST
HYST
REF
REF
+
GND
TEMP
SENSOR
-
GND
TEMP
SENSOR
-
VTEMP
V+
VTEMP
V+
LM27__K
LM27__J
Figure 1. LM27-_ _J
V+
HYST
+
Figure 2. LM27-_ _K
OS
V+
HYST
HYST
REF
REF
+
GND
TEMP
SENSOR
US
HYST
-
GND
TEMP
SENSOR
-
VTEMP
V+
+
VTEMP
LM27__L
V+
LM27__N
Figure 3. LM27-_ _L
Figure 4. LM27-_ _N
The LM27 can be factory programmed to have a trip point anywhere in-between 120°C to 150°C.
Applications Hints
AFTER-ASSEMBLY PCB TESTING
The LM27's VTEMP output allows after-assembly PCB testing by following a simple test procedure. Simply
measuring the VTEMP output voltage will verify that the LM27 has been assembled properly and that its
temperature sensing circuitry is functional. The VTEMP output has very weak drive capability that can be
overdriven by 1.5mA. Therefore, one can simply force the VTEMP voltage to cause the digital output to change
state, thereby verifying that the comparator and output circuitry function after assembly. Here is a sample test
procedure that can be used to test the LM27CIM5X-2HJ which has a 140°C trip point.
1. Turn on V+ and measure VTEMP. Then calculate the temperature reading of the LM27 using the equation:
VO = (−3.552×10−6×(T−30)2) + (−10.69576×10−3×(T−30)) + 1.8386V
(2)
or
T = -1475.49 + 2.2668 x 106 +
1.8386 - VTEMP
3.552 x 10-6
(3)
2. Verify that the temperature measured in step one is within (±3°C + error of reference temperature sensor) of
the ambient/board temperature. The ambient/board temperature (reference temperature) should be
measured using an extremely accurate calibrated temperature sensor, which is in close proximity to and
mounted on the same PCB as the LM27 perhaps even touching the GND lead of the LM27 if possible. The
LM27 will sence the board temperature not the ambient temperature (see MOUNTING CONSIDERATIONS)
3.
(a) Observe that OS is high.
(b) Drive VTEMP to ground.
(c) Observe that OS is now low.
(d) Release the VTEMP pin.
(e) Observe that OS is now high.
4.
(a) Observe that OS is high.
(b) Drive VTEMP voltage down gradually.
(c) When OS goes low, note the VTEMP voltage.
(d) VTEMPTrig = VTEMP at OS trigger (HIGH->LOW)
(e) Calculate Ttrig using Equation 3.
6
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM27
LM27
www.ti.com
SNIS124D – AUGUST 2002 – REVISED JULY 2013
5.
(a) Gradually raise VTEMP until OS goes HIGH. Note VTEMP.
(b) Calculate THYST using Equation 3.
VTEMP LOADING
The VTEMP output has very weak drive capability (1 µA source, 40 µA sink). So care should be taken when
attaching circuitry to this pin. Capacitive loading may cause the VTEMP output to oscillate. Simply adding a resistor
in series as shown in Figure 6 will prevent oscillations from occurring. To determine the value of the resistor
follow the guidelines given in Table 3. The same value resistor will work for either placement of the resistor. If an
additional capacitive load is placed directly on the LM27 output, rather than across CLOAD, it should be at least a
factor of 10 smaller than CLOAD.
Table 3. Resistive compensation for capacitive loading of VTEMP
CLOAD
R (Ω)
≤100pF
0
1nF
8200
10nF
3000
100nF
1000
≥1µF
430
Resistor placement for capacitive loading compensation of VTEMP
Heavy Capacitive
Load, Cable/Wiring
HYST
OS/OS/US/
US
GND LM27
VTEMP
V+
CLOAD
0.1PF
R
Figure 5. R in series with capacitor
Heavy Capacitive
Load, Cable/Wiring
HYST
R
OS/OS/US/
US
GND LM27
VTEMP
V+
CLOAD
0.1Pf
Figure 6. R in series with signal path
NOISE CONSIDERATIONS
The LM27 has excellent power supply noise rejection. Listed below is a variety of signals used to test the LM27
power supply rejection. False triggering of the output was not observed when these signals where coupled into
the V+ pin of the LM27.
• square wave 400kHz, 1Vp-p
• square wave 2kHz, 200mVp-p
• sine wave 100Hz to 1MHz, 200mVp-p
Testing was done while maintaining the temperature of the LM27 one degree centigrade way from the trip point
with the output not activated.
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM27
7
LM27
SNIS124D – AUGUST 2002 – REVISED JULY 2013
www.ti.com
MOUNTING CONSIDERATIONS
The LM27 can be applied easily in the same way as other integrated-circuit temperature sensors. It can be glued
or cemented to a surface. The temperature that the LM27 is sensing will be within about +0.06°C of the surface
temperature to which the LM27's leads are attached to.
This presumes that the ambient air temperature is almost the same as the surface temperature; if the air
temperature were much higher or lower than the surface temperature, the actual temperature measured would
be at an intermediate temperature between the surface temperature and the air temperature.
To ensure good thermal conductivity, the backside of the LM27 die is directly attached to the GND pin (pin 2).
The temperatures of the lands and traces to the other leads of the LM27 will also affect the temperature that is
being sensed.
Alternatively, the LM27 can be mounted inside a sealed-end metal tube, and can then be dipped into a bath or
screwed into a threaded hole in a tank. As with any IC, the LM27 and accompanying wiring and circuits must be
kept insulated and dry, to avoid leakage and corrosion. This is especially true if the circuit may operate at cold
temperatures where condensation can occur. Printed-circuit coatings and varnishes such as Humiseal and epoxy
paints or dips are often used to ensure that moisture cannot corrode the LM27 or its connections.
The junction to ambient thermal resistance (θJA) is the parameter used to calculate the rise of a part's junction
temperature due to its power dissipation. For the LM27 the equation used to calculate the rise in the die junction
temperature is as follows:
TJ = TA + 4JA(V+IQ + (V+ - VTEMP)IL_TEMP + VDOIDO)
(4)
+
where TA is the ambient temperature, V is the power supply voltage, IQ is the quiescent current, IL_TEMP is the
load current on the VTEMP output, VDO is the voltage on the digital output, and IDO is the load current on the digital
output. Since the LM27's junction temperature is the actual temperature being measured, care should be taken
to minimize the load current that the LM27 is required to drive.
The tables shown in Table 4 summarize the thermal resistance for different conditions and the rise in die
temperature of the LM27 without any loading on VTEMP and a 10k pull-up resistor on an open-drain digital output
with a 5.5V power supply.
Table 4. Thermal resistance (θJA) and temperature rise due to self heating (TJ−TA)
SOT23-5
no heat sink
SOT23-5
small heat sink
θJA
(°C/W)
TJ−TA
(°C)
θJA
(°C/W)
TJ−TA
(°C)
Still Air
250
0.11
TBD
TBD
Moving Air
TBD
TBD
TBD
TBD
Typical Applications
System Fan
Sanyo Denki
109R0612T4H12
12V
HYST
OS
GND LM27
VTEMP
V+
+5V
10k
0.1PF
The fan's control pin has internal pull-up. The 10k pull-down sets a slow fan speed. When the output of the LM27
goes low, the fan will speed up.
Figure 7. Two Speed Fan Speed Control
8
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM27
LM27
www.ti.com
SNIS124D – AUGUST 2002 – REVISED JULY 2013
5V
HYST
OS
GND LM27
VTEMP
V+
NDS356P
R1
(100k)
0.1
1N4001
5V
5V Fan
MC05J3
Comair-Rotron
Figure 8. Fan High Side Drive
12V
1N4001
Vout
TOYO
USTF802512HW
HYST
OS
GND LM27
VTEMP
V+
R1
(10k)
2N2222
0.1
5V
Figure 9. Fan Low Side Drive
5V
THERMALLY COUPLED
+28V
8:
HYST
IC2 OS
GND LM27
VTEMP
V+
+
-
NDS356P
100k
IC1 -28V
LM3886
20k
1k
3.3PF
47k
Audio
Input
1N4001
5V
0.1PF
5V Fan
MC05J3
Comair-Rotron
10PF
Figure 10. Audio Power Amplifier Thermal Protection
5V
HYST
OS
GND LM27
VTEMP
V+
Heater
Supply
R1
(10k)
Heater
0.1
5V
Figure 11. Simple Thermostat
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM27
9
LM27
SNIS124D – AUGUST 2002 – REVISED JULY 2013
www.ti.com
REVISION HISTORY
Changes from Revision B (March 2013) to Revision C
•
10
Page
Deleted layout of National Data Sheet to TI format .............................................................................................................. 9
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM27
PACKAGE OPTION ADDENDUM
www.ti.com
26-Jul-2016
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM27-2PL MDA
ACTIVE
DIESALE
Y
0
7000
Green (RoHS
& no Sb/Br)
Call TI
Level-1-NA-UNLIM
-40 to 85
LM27CIM5-1HJ/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
120 to 150
T1HJ
LM27CIM5-2HJ/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
120 to 150
T2HJ
LM27CIM5-ZHJ/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
120 to 150
TZHJ
LM27CIM5X-1HJ/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
T1HJ
LM27CIM5X-2HJ/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
T2HJ
LM27CIM5X-ZHJ/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
TZHJ
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
26-Jul-2016
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
LM27CIM5-1HJ/NOPB
SOT-23
DBV
5
1000
178.0
8.4
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
3.2
3.2
1.4
4.0
8.0
Q3
LM27CIM5-2HJ/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM27CIM5-ZHJ/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM27CIM5X-1HJ/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM27CIM5X-2HJ/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM27CIM5X-ZHJ/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM27CIM5-1HJ/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM27CIM5-2HJ/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM27CIM5-ZHJ/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM27CIM5X-1HJ/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM27CIM5X-2HJ/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM27CIM5X-ZHJ/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated
Similar pages