TI1 LM2903ITL Lm193/lm293/lm393/lm2903 low power low offset voltage dual comparator Datasheet

LM193,LM2903,LM293,LM393
LM193/LM293/LM393/LM2903 Low Power Low Offset Voltage Dual Comparators
Literature Number: SNOSBJ6D
LM193/LM293/LM393/LM2903
Low Power Low Offset Voltage Dual Comparators
General Description
Advantages
The LM193 series consists of two independent precision
voltage comparators with an offset voltage specification as
low as 2.0 mV max for two comparators which were designed specifically to operate from a single power supply
over a wide range of voltages. Operation from split power
supplies is also possible and the low power supply current
drain is independent of the magnitude of the power supply
voltage. These comparators also have a unique characteristic in that the input common-mode voltage range includes
ground, even though operated from a single power supply
voltage.
n
n
n
n
n
n
Application areas include limit comparators, simple analog to
digital converters; pulse, squarewave and time delay generators; wide range VCO; MOS clock timers; multivibrators
and high voltage digital logic gates. The LM193 series was
designed to directly interface with TTL and CMOS. When
operated from both plus and minus power supplies, the
LM193 series will directly interface with MOS logic where
their low power drain is a distinct advantage over standard
comparators.
The LM393 and LM2903 parts are available in National’s
innovative thin micro SMD package with 8 (12 mil) large
bumps.
Squarewave Oscillator
High precision comparators
Reduced VOS drift over temperature
Eliminates need for dual supplies
Allows sensing near ground
Compatible with all forms of logic
Power drain suitable for battery operation
Features
n Wide supply
— Voltage range:
2.0V to 36V
± 1.0V to ± 18V
— Single or dual supplies:
n Very low supply current drain (0.4 mA) — independent
of supply voltage
n Low input biasing current:
25 nA
± 5 nA
n Low input offset current:
± 3 mV
n Maximum offset voltage:
n Input common-mode voltage range includes ground
n Differential input voltage range equal to the power
supply voltage
n Low output saturation voltage,:
250 mV at 4 mA
n Output voltage compatible with TTL, DTL, ECL, MOS
and CMOS logic systems
n Available in the 8-Bump (12 mil) micro SMD package
n See AN-1112 for micro SMD considerations
Non-Inverting Comparator with Hysteresis
00570909
00570938
© 2002 National Semiconductor Corporation
DS005709
www.national.com
LM193/LM293/LM393/LM2903 Low Power Low Offset Voltage Dual Comparators
August 2002
LM193/LM293/LM393/LM2903
Schematic and Connection Diagrams
00570902
Metal Can Package
Dual-In-Line/SOIC Package
00570901
00570903
micro SMD
micro SMD Marking
00570945
Top View
00570946
Top View
www.national.com
2
LM193/LM193A
(Note 10)
LM2903
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage, V+
36V
Differential Input Voltage (Note 8)
36V
Input Voltage
−40˚C to +85˚C
Storage Temperature Range
−65˚C to +150˚C
Lead Temperature
(Soldering, 10 seconds)
+260˚C
Soldering Information
−0.3V to +36V
Input Current (VIN < −0.3V) (Note 3)
−55˚C to +125˚C
Dual-In-Line Package
50 mA
Soldering (10 seconds)
Power Dissipation (Note 1)
260˚C
Small Outline Package
Molded DIP
215˚C
780 mW
Vapor Phase (60 seconds)
Metal Can
660 mW
Infrared (15 seconds)
Small Outline Package
510 mW
micro SMD Pacakge
See AN-450 “Surface Mounting Methods and Their Effect
on Product Reliability” for other methods of soldering
surface mount devices.
568mW
Output Short-Circuit to Ground
(Note 2)
220˚C
ESD rating
Continuous
(1.5 kΩ in series with 100 pF)
Operating Temperature Range
LM393
0˚C to +70˚C
LM293
−25˚C to +85˚C
1300V
Electrical Characteristics
(V+ =5V, TA = 25˚C, unless otherwise stated)
Parameter
Conditions
LM193A
Min
Units
Typ
Max
Input Offset Voltage
(Note 9)
1.0
2.0
mV
Input Bias Current
IIN(+) or IIN(−) with Output In Linear
25
100
nA
25
nA
Range, VCM = 0V (Note 5)
Input Offset Current
IIN(+)−IIN(−) VCM = 0V
Input Common Mode
3.0
V+ = 30V (Note 6)
+
0
V −1.5
V
Voltage Range
RL = ∞
Supply Current
V+ =5V
0.4
1
mA
V+ =36V
1
2.5
mA
RL≥15 kΩ, V+ =15V
Voltage Gain
50
200
V/mV
300
ns
VO = 1V to 11V
Large Signal Response
VIN =TTL Logic Swing, VREF =1.4V
Time
VRL =5V, RL =5.1 kΩ
Response Time
VRL =5V, RL =5.1 kΩ (Note 7)
Output Sink Current
VIN(−)=1V, VIN(+)=0, VO≈1.5V
Saturation Voltage
VIN(−)=1V, VIN(+)=0, ISINK≤4 mA
250
Output Leakage Current
VIN(−)=0, VIN(+)=1V, VO =5V
0.1
6.0
1.3
µs
16
mA
400
mV
nA
Electrical Characteristics
(V+ =5V, TA = 25˚C, unless otherwise stated)
Parameter
Input Offset Voltage
Input Bias Current
Conditions
LM193
LM293, LM393
LM2903
Units
Min Typ
Max
Min Typ
Max
Min Typ
Max
(Note 9)
1.0
5.0
1.0
5.0
2.0
7.0
mV
IIN(+) or IIN(−) with Output In
25
100
25
250
25
250
nA
3.0
25
5.0
50
5.0
50
nA
V+−1.5
V
Linear Range, VCM = 0V (Note 5)
Input Offset Current
IIN(+)−IIN(−) VCM = 0V
Input Common Mode
V+ = 30V (Note 6)
0
V+−1.5
0
V+−1.5
0
Voltage Range
3
www.national.com
LM193/LM293/LM393/LM2903
Absolute Maximum Ratings
LM193/LM293/LM393/LM2903
Electrical Characteristics
(Continued)
(V+ =5V, TA = 25˚C, unless otherwise stated)
Parameter
Conditions
LM193
Min Typ
Supply Current
Voltage Gain
RL = ∞
LM293, LM393
Max
Min Typ
LM2903
Max
Min Typ
Units
Max
V+ =5V
0.4
1
0.4
1
0.4
1.0
mA
V+ =36V
1
2.5
1
2.5
1
2.5
mA
RL≥15 kΩ, V+ =15V
50
200
50
200
25
100
V/mV
300
ns
VO = 1V to 11V
Large Signal Response
VIN =TTL Logic Swing, VREF =1.4V
Time
VRL =5V, RL =5.1 kΩ
Response Time
VRL =5V, RL =5.1 kΩ (Note 7)
Output Sink Current
VIN(−)=1V, VIN(+)=0, VO≤1.5V
300
300
1.3
6.0
1.3
16
6.0
Saturation Voltage
VIN(−)=1V, VIN(+)=0, ISINK≤4 mA
250
Output Leakage Current
VIN(−)=0, VIN(+)=1V, VO =5V
0.1
16
400
1.5
µs
16
mA
6.0
250
400
250
0.1
400
mV
0.1
nA
Electrical Characteristics
(V+ = 5V) (Note 4)
Parameter
Conditions
LM193A
Min
Input Offset Voltage
Units
Typ
Max
(Note 9)
4.0
mV
Input Offset Current
IIN(+)−IIN(−), VCM =0V
100
nA
Input Bias Current
IIN(+) or IIN(−) with Output in Linear Range,
300
nA
V+−2.0
V
VCM =0V (Note 5)
Input Common Mode
Voltage Range
V+ =30V (Note 6)
Saturation Voltage
VIN(−)=1V, VIN(+)=0, ISINK≤4 mA
700
mV
Output Leakage Current
VIN(−)=0, VIN(+) =1V, VO =30V
1.0
µA
Differential Input Voltage
Keep All VIN’s≥0V (or V−, if Used), (Note 8)
36
V
0
Electrical Characteristics
(V+ = 5V) (Note 4)
Parameter
Conditions
LM193
Min Typ
LM293, LM393
Max
Min Typ
Max
LM2903
Min Typ
Units
Max
Input Offset Voltage
(Note 9)
9
9
9
15
mV
Input Offset Current
IIN(+)−IIN(−), VCM =0V
100
150
50
200
nA
Input Bias Current
IIN(+) or IIN(−) with Output in
Linear Range, VCM =0V
(Note 5)
300
400
200
500
nA
Input Common Mode
Voltage Range
V+ =30V (Note 6)
V+−2.0
V
Saturation Voltage
VIN(−)=1V, VIN(+)=0,
ISINK≤4 mA
700
700
700
mV
Output Leakage Current
VIN(−)=0, VIN(+) =1V, VO =30V
1.0
1.0
1.0
µA
Differential Input Voltage
Keep All VIN’s≥0V (or V−, if
Used), (Note 8)
36
36
36
V
V+−2.0
0
0
V+−2.0
0
400
Note 1: For operating at high temperatures, the LM393 and LM2903 must be derated based on a 125˚C maximum junction temperature and a thermal resistance
of 170˚C/W which applies for the device soldered in a printed circuit board, operating in a still air ambient. The LM193/LM193A/LM293 must be derated based on
a 150˚C maximum junction temperature. The low bias dissipation and the “ON-OFF” characteristic of the outputs keeps the chip dissipation very small (PD≤100 mW),
provided the output transistors are allowed to saturate.
Note 2: Short circuits from the output to V+ can cause excessive heating and eventual destruction. When considering short circuits to ground, the maximum output
current is approximately 20 mA independent of the magnitude of V+.
Note 3: This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP
transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also lateral NPN parasitic transistor action
www.national.com
4
(Continued)
on the IC chip. This transistor action can cause the output voltages of the comparators to go to the V+ voltage level (or to ground for a large overdrive) for the time
duration that an input is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which was negative, again returns
to a value greater than −0.3V.
Note 4: These specifications are limited to −55˚C≤TA≤+125˚C, for the LM193/LM193A. With the LM293 all temperature specifications are limited to
−25˚C≤TA≤+85˚C and the LM393 temperature specifications are limited to 0˚C≤TA≤+70˚C. The LM2903 is limited to −40˚C≤TA≤+85˚C.
Note 5: The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output so
no loading change exists on the reference or input lines.
Note 6: The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode
voltage range is V+−1.5V at 25˚C, but either or both inputs can go to 36V without damage, independent of the magnitude of V+.
Note 7: The response time specified is for a 100 mV input step with 5 mV overdrive. For larger overdrive signals 300 ns can be obtained, see typical performance
characteristics section.
Note 8: Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode range, the
comparator will provide a proper output state. The low input voltage state must not be less than −0.3V (or 0.3V below the magnitude of the negative power supply,
if used).
Note 9: At output switch point, VO.1.4V, RS =0Ω with V+ from 5V to 30V; and over the full input common-mode range (0V to V+−1.5V), at 25˚C.
Note 10: Refer to RETS193AX for LM193AH military specifications and to RETS193X for LM193H military specifications.
Ordering Information
Package
Temperature Range
Part Number
NSC Drawing
LM193H*
LM193H/883
LM193H-MLS
LM193AH-MLS
−55˚C to 125˚C
LM193AH-QMLV**
8-Pin Metal Can
H08C
LM193AH
LM193AH/883
−25˚C to 85˚C
LM293H
0˚C to 70˚C
LM393H
LM193J/883*
8-Pin Ceramic DIP
LM193AJ/883
−55˚C to 125˚C
LM193AJ-QMLV**
J08A
LM193AJ-MLS
8-Pin Molded DIP
0˚C to 70˚C
LM393N
−40˚C to 85˚C
LM2903N
LM393M
0˚C to 70˚C
LM393MX
8-Pin SOIC
LM2903M
−40˚C to 85˚C
8-Bump (12 mils)
micro SMD
N08E
M08A
LM2903MX
LM393TL
0˚C to 70˚C
LM393TLX
LM2903ITL
−40˚C to 85˚C
TLA08AAA
LM2903ITLX
Note: * Also available per LM38510/11202
Note: ** See STD Mil DWG 5962-94526
5
www.national.com
LM193/LM293/LM393/LM2903
Electrical Characteristics
LM193/LM293/LM393/LM2903
Typical Performance Characteristics
LM193/LM293/LM393, LM193A
Supply Current
Input Current
00570925
00570926
Response Time for Various Input Overdrives — Negative
Transition
Output Saturation Voltage
00570928
00570927
Response Time for Various Input Overdrives — Positive
Transition
00570929
www.national.com
6
LM193/LM293/LM393/LM2903
Typical Performance Characteristics
LM2903
Supply Current
Input Current
00570931
00570930
Response Time for Various Input Overdrives — Negative
Transition
Output Saturation Voltage
00570933
00570932
Response Time for Various Input Overdrives — Positive
Transition
00570934
7
www.national.com
LM193/LM293/LM393/LM2903
Application Hints
The differential input voltage may be larger than V+ without
damaging the device (Note 8). Protection should be provided
to prevent the input voltages from going negative more than
−0.3 VDC (at 25˚C). An input clamp diode can be used as
shown in the applications section.
The LM193 series are high gain, wide bandwidth devices
which, like most comparators, can easily oscillate if the
output lead is inadvertently allowed to capacitively couple to
the inputs via stray capacitance. This shows up only during
the output voltage transition intervals as the comparator
change states. Power supply bypassing is not required to
solve this problem. Standard PC board layout is helpful as it
reduces stray input-output coupling. Reducing the input resistors to < 10 kΩ reduces the feedback signal levels and
finally, adding even a small amount (1.0 to 10 mV) of positive
feedback (hysteresis) causes such a rapid transition that
oscillations due to stray feedback are not possible. Simply
socketing the IC and attaching resistors to the pins will cause
input-output oscillations during the small transition intervals
unless hysteresis is used. If the input signal is a pulse
waveform, with relatively fast rise and fall times, hysteresis is
not required.
All input pins of any unused comparators should be tied to
the negative supply.
The output of the LM193 series is the uncommitted collector
of a grounded-emitter NPN output transistor. Many collectors
can be tied together to provide an output OR’ing function. An
output pull-up resistor can be connected to any available
power supply voltage within the permitted supply voltage
range and there is no restriction on this voltage due to the
magnitude of the voltage which is applied to the V+ terminal
of the LM193 package. The output can also be used as a
simple SPST switch to ground (when a pull-up resistor is not
used). The amount of current which the output device can
sink is limited by the drive available (which is independent of
V+) and the β of this device. When the maximum current limit
is reached (approximately 16mA), the output transistor will
come out of saturation and the output voltage will rise very
rapidly. The output saturation voltage is limited by the approximately 60Ω rSAT of the output transistor. The low offset
voltage of the output transistor (1.0mV) allows the output to
clamp essentially to ground level for small load currents.
The bias network of the LM193 series establishes a drain
current which is independent of the magnitude of the power
supply voltage over the range of from 2.0 VDC to 30 VDC.
It is usually unnecessary to use a bypass capacitor across
the power supply line.
Typical Applications
(V+ =5.0 VDC)
Basic Comparator
Driving CMOS
Driving TTL
00570935
00570936
Squarewave Oscillator
Pulse Generator
00570937
Crystal Controlled Oscillator
00570938
00570940
00570939
* For large ratios of R1/R2,
D1 can be omitted.
www.national.com
8
LM193/LM293/LM393/LM2903
Typical Applications (V+ =5.0 VDC)
(Continued)
Two-Decade High Frequency VCO
00570941
V* = +30 VDC
+250 mVDC ≤ VC ≤ +50 VDC
700Hz ≤ fo ≤ 100kHz
Basic Comparator
Non-Inverting Comparator with Hysteresis
00570906
00570909
Inverting Comparator with Hysteresis
Output Strobing
00570910
00570911
9
www.national.com
LM193/LM293/LM393/LM2903
Typical Applications (V+ =5.0 VDC)
(Continued)
AND Gate
OR Gate
00570913
00570912
Large Fan-in AND Gate
Limit Comparator
00570915
00570914
Comparing Input Voltages of Opposite Polarity
ORing the Outputs
00570916
00570917
www.national.com
10
LM193/LM293/LM393/LM2903
Typical Applications (V+ =5.0 VDC)
(Continued)
Zero Crossing Detector (Single Power Supply)
One-Shot Multivibrator
00570921
00570922
Bi-Stable Multivibrator
One-Shot Multivibrator with Input Lock Out
00570924
00570923
Zero Crossing Detector
Comparator With a Negative Reference
00570944
00570943
11
www.national.com
LM193/LM293/LM393/LM2903
Typical Applications (V+ =5.0 VDC)
(Continued)
Time Delay Generator
00570907
Split-Supply Applications
(V+ =+15 VDC and V− =−15 VDC)
MOS Clock Driver
00570942
www.national.com
12
LM193/LM293/LM393/LM2903
Physical Dimensions
inches (millimeters) unless otherwise noted
Metal Can Package (H)
NS Package Number H08C
Ceramic Dual-In-Line Package
NS Package Number J08A
13
www.national.com
LM193/LM293/LM393/LM2903
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
SOIC Package
NS Package Number M08A
Molded Dual-In-Line Package (N)
NS Package N08E
www.national.com
14
inches (millimeters) unless otherwise noted (Continued)
NOTE: UNLESS OTHERWISE SPECIFIED
1. EPOXY COATING
2. 63Sn/37Pb EUTECTIC BUMP
3. RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD.
4. PIN A1 IS ESTABLISHED BY LOWER LEFT CORNER WITH RESPECT TO TEXT ORIENTATION REMAINING PINS ARE NUMBERED
COUNTERCLOCKWISE.
5. XXX IN DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE X1 IS PACKAGE WIDTH, X2 IS PACKAGE LENGTH AND X3 IS
PACKAGE HEIGHT.
6. REFERENCE JEDEC REGISTRATION MO-211, VARIATION BC.
8-Bump (12 mil) micro SMD Package
NS Package TLA08AAA
X1 = 1.514mm X2 = 1.514mm X3 = 0.600mm
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
National Semiconductor
Corporation
Americas
Email: [email protected]
www.national.com
National Semiconductor
Europe
Fax: +49 (0) 180-530 85 86
Email: [email protected]
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: [email protected]
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
LM193/LM293/LM393/LM2903 Low Power Low Offset Voltage Dual Comparators
Physical Dimensions
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and Automotive www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
www.ti.com/video
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
Similar pages