NSC LM2927T Low dropout regulator with delayed reset Datasheet

LM2926/LM2927
Low Dropout Regulator with Delayed Reset
General Description
Features
The LM2926 is a 5V, 500 mA, low dropout regulator with delayed reset. The microprocessor reset flag is set low by thermal shutdown, short circuits, overvoltage conditions, dropout, and power-up. After the fault condition is corrected, the
reset flag remains low for a delay time determined by the delay capacitor. Hysteresis is included in the reset circuit to
prevent oscillations, and a reset output is guaranteed down
to 3.2V supply input. A latching comparator is used to discharge the delay capacitor, which guarantees a full reset
pulse even when triggered by a relatively short fault condition. A patented quiescent current reduction circuit drops the
ground pin current to 8 mA at full load when the input-output
differential is 3V or more.
Familiar PNP regulator features such as reverse battery protection, transient protection, and overvoltage shutdown are
included in the LM2926 making it suitable for use in automotive and battery operated equipment.
The LM2927 is electrically identical to the LM2926 but has a
different pin-out. The LM2927 is pin-for-pin compatible with
the L4947 and TLE4260 alternatives. The LM2926 is
pin-for-pin compatible with the LM2925.
n
n
n
n
n
n
n
n
5% output accuracy over entire operating range
Dropout voltage typically 350 mV at 500 mA output
Externally programmed reset delay
Short circuit proof
Reverse battery proof
Thermally protected
LM2926 is pin-for-pin compatible with the LM2925
P+ Product Enhancement tested
Applications
n Battery operated equipment
n Microprocessor-based systems
n Portable instruments
Typical Application
DS010759-1
*Required if regulator is located far ( > 2") from power supply filter.
**CO must be at least 10 µF to maintain stability. May be increased without bound to maintain regulation during transients. Locate as close as possible to
the regulator. This capacitor msut be rated over the same operating temperature range as the regulator. The equivalent series resistance (ESR) of this
capacitor is critical; see curve under Typical Performance Characteristics.
Connection Diagrams and Ordering Information
5–Lead TO-220
5-Lead TO-220
DS010759-2
Front View
Order Number LM2926T
See NS Package Number TO5A
© 1998 National Semiconductor Corporation
DS010759
DS010759-14
Front View
Order Number LM2927T
See NS Package Number TO5A
www.national.com
LM2926/LM2927 Low Dropout Regulator with Delayed Reset
April 1998
Absolute Maximum Ratings (Note 1)
Power Dissipation (Note 3)
Junction Temperature (TJMAX)
Storage Temperature Range
Lead Temperature
(Soldering, 10 sec.)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Input Voltage
Survival
t = 100 ms
t = 1 ms
Continuous
Reset Output Sink Current
ESD Susceptibility (Note 2)
Internally Limited
150˚C
−40˚C to +150˚C
260˚C
Operating Ratings(Note 1)
80V
−50V
−18V to +26V
10 mA
2 kV
Junction Temperature Range (TJ)
Maximum Input Voltage
−40˚C to +125˚C
26V
Electrical Characteristics
VIN = 14.4V, CO = 10 µF, −40˚C ≤ TJ ≤ 125˚C, unless otherwise specified.
Parameter
Conditions
Typ
Limit
Units
(Note 4)
(Note 5)
(Limit)
4.85
V (min)
5.15
V (max)
4.75
V (min)
5.25
V (max)
25
mV (max)
50
mV (max)
60
mV (max)
3
mA (max)
30
mA (max)
10
mA (max)
60
mA (max)
200
mV (max)
300
mV (max)
600
mV (max)
REGULATOR OUTPUT
Output Voltage
5 mA ≤ IO ≤ 500 mA,
TJ = 25˚C
5
5 mA ≤ IO ≤ 500 mA
V
5
Line Regulation
IO = 5 mA, 9V ≤ VIN ≤ 16V
IO = 5 mA, 7V ≤ VIN ≤ 26V
Load Regulation
Quiescent Current
5 mA ≤ IO ≤ 500 mA
IO = 5 mA
3
mV
mV
mA
8
IO = 5 mA, VIN = 5V
mA
3
mA
25
IO = 5 mA, TJ = 25˚C
mA
60
IO = 5 mA
IO = 500 mA, TJ = 25˚C
Short Circuit Current
mV
2
IO = 500 mA, VIN = 6V
Dropout Voltage (Note 6)
1
5
IO = 500 mA
Quiescent Current at Low VIN
V
mV
350
IO = 500 mA
VIN = 8V, RL = 1Ω
mV
700
mV (max)
800
mA (min)
3
A (max)
60
dB (min)
2
Output Impedance
ƒRIPPLE = 120 Hz, VRIPPLE = 1 Vrms,
IO = 50 mA
IO = 50 mAdc and 10 mArms @ 1 kHz
Output Noise
10 Hz to 100 kHz, IO = 50 mA
Ripple Rejection
Long Term Stability
www.national.com
2
A
100
mΩ
1
mVrms
20
mV/1000 Hr
Electrical Characteristics
(Continued)
VIN = 14.4V, CO = 10 µF, −40˚C ≤ TJ ≤ 125˚C, unless otherwise specified.
Parameter
Conditions
Typ
Limit
Units
(Note 4)
(Note 5)
(Limit)
V (min)
REGULATOR OUTPUT
Maximum Operational Input
Voltage
Continuous
26
Peak Transient Input Voltage
VO ≤ 7V, RL = 100Ω, tf = 100 ms
VO ≥ −0.6V, RL = 100Ω
80
V (min)
Reverse DC Input Voltage
−18
V (min)
Reverse Transient Input Voltage
tr = 1 ms, RL = 100Ω
−50
V (min)
−80
mV (min)
−400
mV (max)
0.4
V (max)
RESET OUTPUT
∆VO Required for Reset Condition (Note 7)
Threshold
−250
ISINK = 1.6 mA, VIN = 3.2V
Output Low Voltage
0.15
Internal Pull-Up Resistance
30
kΩ
ms
Delay Time
CDELAY = 10 nF (See Timing Curve)
19
Minimum Operational VIN
Delayed Reset Output ≤ 0.8V,
ISINK = 1.6 mA, RL = 100Ω
2.2
Delay Reset Output ≤ 0.8V,
ISINK = 10 µA, VIN = 0V
0.7
on Power Up
Minimum Operational VO
on Power Down
mV
V
3.2
V (min)
V
DELAY CAPACITOR PIN
Threshold Difference (∆VDELAY)
Change in Delay Capacitor Voltage Required
for Reset Output to Return High
3.5
V (min)
4.1
V (max)
1.0
µA (min)
3.0
µA (max)
3.75
Charging Current (IDELAY)
V
2.0
µA
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics.
Note 2: Human body model; 100 pF discharged through a 1.5 kΩ resistor.
Note 3: The maximum power dissipation is a function of TJMAX, and θJA, and TA, and is limited by thermal shutdown. The maximum allowable power dissipation at
any ambient temperature is PD = (TJMAX–TA)/θJA. If this dissipation is exceeded, the die temperature will rise above 150˚C and the device will go into thermal shutdown. For the LM2926 and LM2927, the junction-to-ambient thermal resistance is 53˚C/W, and the junction-to-case thermal resistance is 3˚C/W.
Note 4: Typicals are at TJ = 25˚C and represent the most likely parametric norm.
Note 5: Limits are 100% guaranteed by production testing.
Note 6: Dropout voltage is the input-output differential at which the circuit ceases to regulate against any further reduction in input voltage. Dropout voltage is measured when the output voltage (VO) has dropped 100 mV from the nominal value measured at VIN = 14.4V.
Note 7: The reset flag is set LOW when the output voltage has dropped an amount, ∆VO, from the nominal value measured at VIN = 14.4V.
Typical Performance Characteristics
Output Voltage
Low Voltage Behavior
Output at Voltage Extremes
DS010759-16
DS010759-15
3
DS010759-32
www.national.com
Typical Performance Characteristics
(Continued)
Quiescent Current
Supply Current
DS010759-17
Dropout Voltage
Quiescent Current
DS010759-18
Output Current Limit
DS010759-20
Ripple Rejection
Output Capacitor ESR
DS010759-21
Ripple Rejection
DS010759-22
Output Impedance
DS010759-23
Line Transient Response
DS010759-19
DS010759-24
Load Transient Response
DS010759-25
Maximum Power
Dissipation (TO-220)
DS010759-27
DS010759-26
DS010759-28
www.national.com
4
Typical Performance Characteristics
(Continued)
Reset Delay
Reset Delay
DS010759-29
DS010759-30
Typical Circuit Waveforms
DS010759-5
Applications Information
DELAYED RESET
EXTERNAL CAPACITORS
The LM2926/7 output capacitor is required for stability. Without it, the regulator output will oscillate at amplitudes as high
as several volts peak-to-peak at frequencies up to 500 kHz.
Although 10 µF is the minimum recommended value, the actual size and type may vary depending upon the application
load and temperature range. Capacitor equivalent series resistance (ESR) also affects stability. The region of stable operation is shown in the Typical Performance Characteristics (Output Capacitor ESR curve).
Output capacitors can be increased in size to any desired
value above 10 µF. One possible purpose of this would be to
maintain the output voltage during brief conditions of input
transients that might be characteristic of a particular system.
Capacitors must also be rated at all ambient temperatures
expected in the system. Many aluminum electrolytics freeze
at temperatures below −30˚C, reducing their effective capacitance to zero. To maintain regulator stability down to
−40˚C, capacitors rated at that temperature (such as tantalums) must be used.
The delayed reset output is designed to hold a microprocessor in a reset state on system power-up for a programmable
time interval to allow the system clock and other powered circuitry to stabilize. A full reset interval is also generated whenever the output voltage falls out of regulation. The circuit is
tripped whenever the output voltage of the regulator is out of
regulation by the Reset Threshold value. This can be caused
by low input voltages, over current conditions, over-voltage
shutdown, thermal shutdown, and by both power-up and
power-down sequences. When the reset circuit detects one
of these conditions, the delay capacitor is discharged by an
SCR and held in a discharged state by a saturated NPN
switch. As long as the delay capacitor is held low, the reset
output is also held low. Because of the action of the SCR, the
reset output cannot glitch on noise or transient fault conditions. A full reset pulse is obtained for any fault condition that
trips the reset circuit.
When the output regains regulation, the SCR is switched off
and a small current (IDELAY = 2 µA) begins charging the de5
www.national.com
Applications Information
(Continued)
lay capacitor. When the capacitor voltage increases 3.75V
(∆VDELAY) from its discharged value, the reset output is
again set HIGH. The delay time is calculated by:
The constant, 1.9 x 106, has a ± 20% tolerance from device
to device. The total delay time error budget is the sum of the
20% device tolerance and the tolerance of the external capacitor. For a 20% timing capacitor tolerance, the worst case
total timing variation would amount to ± 40%, or a ratio of
2.33:1. In most applications the minimum expected reset
pulse is of interest. This occurs with minimum CDELAY, minimum ∆VDELAY, and maximum IDELAY. ∆VDELAY and IDELAY
are fully specified in the Electrical Characteristics. Graphs
showing the relationship between delay time and both temperature and CDELAY are shown in the Typical Performance
Characteristics.
As shown in Figure 1, the delayed reset output is pulled low
by an NPN transistor (Q2), and pulled high to VO by an internal 30 kΩ resistor (R3) and PNP transistor (Q3). The reset
output will operate when VO is sufficient to bias Q2 (0.7V or
more). At lower voltages the reset output will be in a high impedance condition. Because of differences in the VBE of Q2
and Q3 and the values of R1 and R2, Q2 is guaranteed by
design to bias before Q3, providing a smooth transition from
the high impedance state when VO < 0.7V, to the active low
state when VO > 0.7V.
DS010759-7
FIGURE 2. Reset Output Behavior during Power-Up
Figure 2 is useful for determing reset performance at any
particular input voltage. Dynamic performance at power-up
will closely follow the characteristics illustrated in Figure 2,
except for the delay added by CDELAY when VO reaches 5V.
The dynamic reset characteristics at power-down are illustrated by the curve shown in Figure 3. At time t = 0 the input
voltage is instantaneously brought to 0V, leaving the output
powered by CO. As the voltage on CO decays (discharged by
a 100Ω load resistor), the reset output is held low. As VO
drops below 0.7V, the reset rises up slightly should there be
any external pull-up resistance. With no external resistance,
the reset line stays low throughout the entire power down
cycle. If the input voltage does not fall instantaneously, the
reset signal will tend to follow the performance characteristics shown in Figure 2.
SYSTEM DESIGN CONSIDERATIONS
Many microprocessors are specified for operation at 5V
± 10%, although they often continue operating well outside
this range. Others, such as certain members of the COPS
family of microcontrollers, are specified for operation as low
as 2.4V.
DS010759-6
FIGURE 1. Delay Reset Output
The static reset characteristics are shown in Figure 2. This
shows the relationship between the input voltage, the regultor output and reset output. Plots are shown for various external pull-up resistors ranging in value from 3 kΩ to an open
circuit. Any external pull-up resistance causes the reset output to follow the regulator output until Q2 is biased ON. CDELAY has no effect on this characteristic.
DS010759-8
FIGURE 3. Reset Output Behavior during Power-Down
Of particular concern is low voltage operation, which occurs
in battery operated systems when the battery reaches the
end of its discharge cycle. Under this condition, when the
supply voltage is outside the guaranteed operating range,
the clock may continue to run and the microprocessor will attempt to execute instructions. If the supply voltage is outside
the guaranteed operating range, the instructions may not execute properly and a hardware reset such as is supplied by
www.national.com
6
Applications Information
Typical Applications
(Continued)
the LM 2926/7 may fail to bring the processor under control.
The LM2926/7 reset output may be more efficiently employed in certain applications as a means of defeating
memory WRITE lines, clocks, or external loads, rather than
depending on unspecified microprocessor operating conditions.
Battery Powered Regulator with Flashing
LED for Low Battery Indication
In critical applications the microprocessor reset input should
be fully characterized and guaranteed to operate until the
clock ceases oscillating.
INPUT TRANSIENTS
The LM2926/7 are guaranteed to withstand positive input
transients to 80V followed by an exponential decay of
τ = 20 ms (tf = 100 ms, or 5 time constants) while maintaining an output of less than 7V. The regulator remains operational to 26 VDC, and shuts down if this value is exceeded.
DS010759-9
General Microprocessor Configuration
DS010759-10
7
www.national.com
Typical Applications
(Continued)
Using the Reset to De-Activate Power Loads. The LM1921 is a Fully Protected 1 Amp High-Side Driver.
DS010759-11
Generating an Active High Reset Signal
DS010759-12
Using the Reset to Ensure an Accurate Display
on Power-Up or Power-Down
DS010759-13
www.national.com
8
9
LM2926/LM2927 Low Dropout Regulator with Delayed Reset
Physical Dimensions
inches (millimeters) unless otherwise noted
5-Lead TO-220 Outline Drawing
Order Number LM2926T or LM2927T
NS Package Number T05A
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
2. A critical component in any component of a life support
1. Life support devices or systems are devices or sysdevice or system whose failure to perform can be reatems which, (a) are intended for surgical implant into
sonably expected to cause the failure of the life support
the body, or (b) support or sustain life, and whose faildevice or system, or to affect its safety or effectiveness.
ure to perform when properly used in accordance
with instructions for use provided in the labeling, can
be reasonably expected to result in a significant injury
to the user.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: [email protected]
www.national.com
National Semiconductor
Europe
Fax: +49 (0) 1 80-530 85 86
Email: [email protected]
Deutsch Tel: +49 (0) 1 80-530 85 85
English Tel: +49 (0) 1 80-532 78 32
Français Tel: +49 (0) 1 80-532 93 58
Italiano Tel: +49 (0) 1 80-534 16 80
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: [email protected]
National Semiconductor
Japan Ltd.
Tel: 81-3-5620-6175
Fax: 81-3-5620-6179
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
Similar pages