TI1 LM4041C12ILPE3 Precision micropower shunt voltage reference Datasheet

LM4041
PRECISION MICROPOWER SHUNT VOLTAGE REFERENCE
www.ti.com
SLCS146E – FEBRUARY 2005 – REVISED FEBRUARY 2006
•
FEATURES
•
•
•
•
•
•
Applications
– Data-Acquisition Systems
– Power Supplies and Power-Supply Monitors
– Instrumentation and Test Equipment
– Process Control
– Precision Audio
– Automotive Electronics
– Energy Management/Metering
– Battery-Powered Equipment
1.225-V Fixed and Adjustable Outputs
(1.225 V to 10 V)
Tight Output Tolerances and Low
Temperature Coefficient
– Max 0.1%, 100 ppm/°C – A Grade
– Max 0.2%, 100 ppm/°C – B Grade
– Max 0.5%, 100 ppm/°C – C Grade
– Max 1.0%, 150 ppm/°C – D Grade
Low Output Noise . . . 20 µVRMS (Typ)
Wide Operating Current Range . . .
45 µA (Typ) to 12 mA
Stable With All Capacitive Loads; No Output
Capacitor Required
Available in
– Industrial Temperature: –40°C to 85°C
– Extended Temperature: –40°C to 125°C
1.2 V . . . DBZ (SOT-23) PACKAGE
(TOP VIEW)
CATHODE
1.2 V . . . DCK (SC-70) PACKAGE
(TOP VIEW)
1
ANODE
3 *
CATHODE 3
* Pin 3 must be connected to
ANODE or left open.
Adjustable . . . DBZ (SOT-23) PACKAGE
(TOP VIEW)
FB
CATHODE
1
NC
4
NC
Adjustable . . . DCK (SC-70) PACKAGE
(TOP VIEW)
NC 1
ANODE
2
ANODE
ANODE
CATHODE
NC
NC − No internal connection
* Pin 2 must be connected to
ANODE or left open.
1
3
5
* 2
ANODE 2
1.2 V . . . LP (TO-92/TO-226) PACKAGE
(TOP VIEW)
5 FB
NC − No internal connection
Adjustable . . . LP (TO-92/TO-226) PACKAGE
(TOP VIEW)
ANODE
2
CATHODE 3
CATHODE
4 NC
FB
NC − No internal connection
DESCRIPTION/ORDERING INFORMATION
The LM4041 series of shunt voltage references are versatile, easy-to-use references suitable for a wide array of
applications. They require no external capacitors for operation and are stable with all capacitive loads.
Additionally, the reference offers low dynamic impedance, low noise, and a low temperature coefficient to ensure
a stable output voltage over a wide range of operating currents and temperatures. The LM4041 uses fuse and
Zener-zap reverse breakdown voltage trim during wafer sort to offer four output voltage tolerances, ranging from
0.1% (max) for the A grade to 1% (max) for the D grade. Thus, a great deal of flexibility is offered to designers in
choosing the best cost-to-performance ratio for their applications. The LM4041 is available in a fixed (1.225 V
nominal) or an adjustable version (which requires an external resistor divider to set the output to a value between
1.225 V and 10 V).
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2005–2006, Texas Instruments Incorporated
LM4041
PRECISION MICROPOWER SHUNT VOLTAGE REFERENCE
www.ti.com
SLCS146E – FEBRUARY 2005 – REVISED FEBRUARY 2006
Packaged in space-saving SC-70 and SOT-23-3 and requiring a minimum current of 45 µA (typ), the LM4041
also is ideal for portable applications. The TO-92 package also is available for through-hole packaging needs.
The LM4041xI is characterized for operation over an ambient temperature range of –40°C to 85°C. The
LM4041xQ is characterized for operation over an ambient temperature range of –40°C to 125°C.
ORDERING INFORMATION
TA
DEVICE GRADE
A grade:
0.1% initial
accuracy
and
100 ppm/°C
temperature
coefficient
PACKAGE (1)
VZ
SC-70 (DCK)
1.2 V
SOT-23-3 (DBZ)
TO-92/TO-226 (LP)
SC-70 (DCK)
B grade:
0.2% initial
accuracy
and
100 ppm/°C
temperature
coefficient
ADJ
SOT-23-3 (DBZ)
TO-92/TO-226 (LP)
SC-70 (DCK)
1.2 V
SOT-23-3 (DBZ)
TO-92/TO-226 (LP)
SC-70 (DCK)
–40°C to 85°C
C grade:
0.5% initial
accuracy
and
100 ppm/°C
temperature
coefficient
ADJ
SOT-23-3 (DBZ)
TO-92/TO-226 (LP)
SC-70 (DCK)
1.2 V
SOT-23-3 (DBZ)
TO-92/TO-226 (LP)
SC-70 (DCK)
D grade:
1.0% initial
accuracy
and
150 ppm/°C
temperature
coefficient
ADJ
SOT-23-3 (DBZ)
TO-92/TO-226 (LP)
SC-70 (DCK)
1.2 V
SOT-23-3 (DBZ)
TO-92/TO-226 (LP)
(1)
(2)
2
ORDERABLE
PART NUMBER
Reel of 3000
LM4041A12IDCKR
Reel of 3000
LM4041A12IDBZR
Reel of 250
LM4041A12IDBZT
Bulk of 1000
LM4041A12ILP
Reel of 2000
LM4041A12ILPR
Reel of 3000
LM4041BIDCKR
Reel of 250
LM4041BIDCKT
Reel of 3000
LM4041BIDBZR
Reel of 250
LM4041BIDBZT
Bulk of 1000
LM4041BILP
Reel of 2000
LM4041BILPR
Reel of 3000
LM4041B12IDCKR
Reel of 3000
LM4041B12IDBZR
Reel of 250
LM4041B12IDBZT
Bulk of 1000
LM4041B12ILP
Reel of 2000
LM4041B12ILPR
Reel of 3000
LM4041CIDCKR
Reel of 250
LM4041CIDCKT
Reel of 3000
LM4041CIDBZR
Reel of 250
LM4041CIDBZT
Bulk of 1000
LM4041CILP
Reel of 2000
LM4041CILPR
Reel of 3000
LM4041C12IDCKR
Reel of 3000
LM4041C12IDBZR
Reel of 250
LM4041C12IDBZT
Bulk of 1000
LM4041C12ILP
Reel of 2000
LM4041C12ILPR
Reel of 3000
LM4041DIDCKR
Reel of 250
LM4041DIDCKT
Reel of 3000
LM4041DIDBZR
Reel of 250
LM4041DIDBZT
Bulk of 1000
LM4041DILP
Reel of 2000
LM4041DILPR
Reel of 3000
LM4041D12IDCKR
Reel of 3000
LM4041D12IDBZR
Reel of 250
LM4041D12IDBZT
Bulk of 1000
LM4041D12ILP
Reel of 2000
LM4041D12ILPR
TOP-SIDE
MARKING (2)
MK_
4MK_
PREVIEW
MG_
4MG_
PREVIEW
ML_
4ML_
PREVIEW
MH_
4MH_
PREVIEW
MM_
4MM_
PREVIEW
MJ_
4MJ_
PREVIEW
MN_
4MN_
PREVIEW
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
DBZ/DCK: The actual top-side marking has one additional character that designates the assembly/test site.
Submit Documentation Feedback
LM4041
PRECISION MICROPOWER SHUNT VOLTAGE REFERENCE
www.ti.com
SLCS146E – FEBRUARY 2005 – REVISED FEBRUARY 2006
ORDERING INFORMATION
TA
–40°C to 125°C
(1)
(2)
DEVICE GRADE
C grade:
0.5% initial
accuracy
and
100 ppm/°C
temperature
coefficient
D grade:
1.0% initial
accuracy
and
150 ppm/°C
temperature
coefficient
VZ
ADJ
PACKAGE (1)
SOT-23-3 (DBZ)
1.2 V
SOT-23-3 (DBZ)
ADJ
SOT-23-3 (DBZ)
1.2 V
SOT-23-3 (DBZ)
ORDERABLE
PART NUMBER
Reel of 3000
LM4041CQDBZR
Reel of 250
LM4041CQDBZT
Reel of 3000
LM4041C12QDBZR
Reel of 250
LM4041C12QDBZT
Reel of 3000
LM4041DQDBZR
Reel of 250
LM4041DQDBZT
Reel of 3000
LM4041D12QDBZR
Reel of 250
LM4041D12QDBZT
TOP-SIDE
MARKING (2)
4MP_
4MS_
4MR_
4MT_
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
DBZ/DCK: The actual top-side marking has one additional character that designates the assembly/test site.
Submit Documentation Feedback
3
LM4041
PRECISION MICROPOWER SHUNT VOLTAGE REFERENCE
www.ti.com
SLCS146E – FEBRUARY 2005 – REVISED FEBRUARY 2006
FUNCTIONAL BLOCK DIAGRAM
CATHODE
+
_
VREF(1)
(2)
FB(1)
(2)
ANODE
(1) LM4041x (ADJ) only
(2) LM4041x12 only
Absolute Maximum Ratings (1)
over free-air temperature range (unless otherwise noted)
MIN
VZ
Continuous cathode voltage
IZ
Continuous cathode current
θJA
Package thermal impedance (2) (3)
TJ
Operating virtual junction temperature
Tstg
Storage temperature range
(1)
(2)
(3)
–10
MAX
V
25
mA
DBZ package
206
DCK package
252
LP package
156
–65
UNIT
15
°C/W
150
°C
150
°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD = (TJ(max) – TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
The package thermal impedance is calculated in accordance with JESD 51-7.
Recommended Operating Conditions
IZ
Cathode current
VZ
Reverse breakdown voltage (adjustable version)
TA
(1)
4
Free-air temperature
MIN
MAX
(1)
12
mA
10
V
LM4041 (I temperature)
–40
85
LM4041 (Q temperature)
–40
125
See parametric tables
Submit Documentation Feedback
UNIT
°C
LM4041
PRECISION MICROPOWER SHUNT VOLTAGE REFERENCE
www.ti.com
SLCS146E – FEBRUARY 2005 – REVISED FEBRUARY 2006
LM4041x12I Electrical Characteristics
full-range TA = –40°C to 85°C (unless otherwise noted)
PARAMETER
VZ
TEST CONDITIONS
Reverse breakdown
voltage
IZ = 100 µA
Reverse breakdown
voltage tolerance
IZ = 100 µA
IZ,min
Minimum cathode
current
αVZ
Average temperature
coefficient of reverse
breakdown voltage
TYP
1 mA < IZ < 12 mA
TYP
MAX
1.225
–1.2
1.2
–2.4
2.4
–9.2
9.2
–10.4
10.4
45
75
45
80
±20
±20
25°C
±15
±15
±100
25°C
±15
25°C
0.7
Full range
25°C
±100
Full range
mV
µA
ppm/°C
±15
1.5
0.7
2
4
75
80
25°C
UNIT
V
25°C
Full range
IZ,min < IZ < 1 mA
MIN
Full range
25°C
IZ = 1 mA
LM4041B12I
MAX
1.225
Full range
IZ = 100 µA
∆VZ/∆IZ
LM4041A12I
MIN
25°C
IZ = 10 mA
Reverse breakdown
voltage change with
cathode current change
TA
6
1.5
2
4
8
6
mV
8
ZZ
Reverse dynamic
impedance
IZ = 1 mA, f = 120 Hz,
IAC = 0.1 IZ
25°C
0.5
eN
Wideband noise
IZ = 100 µA,
10 Hz ≤ f ≤ 10 kHz
25°C
20
20
µVRMS
Long-term stability of
reverse breakdown
voltage
t = 1000 h,
TA = 25°C ± 0.1°C,
IZ = 100 µA
25°C
120
120
ppm
Submit Documentation Feedback
1.5
0.5
1.5
Ω
5
LM4041
PRECISION MICROPOWER SHUNT VOLTAGE REFERENCE
www.ti.com
SLCS146E – FEBRUARY 2005 – REVISED FEBRUARY 2006
LM4041x12I Electrical Characteristics
full-range TA = –40°C to 85°C (unless otherwise noted)
PARAMETER
VZ
TEST CONDITIONS
Reverse breakdown
voltage
IZ = 100 µA
Reverse breakdown
voltage tolerance
IZ = 100 µA
IZ,min
Minimum cathode
current
αVZ
Average temperature
coefficient of reverse
breakdown voltage
TYP
1 mA < IZ < 12 mA
TYP
MAX
1.225
–6
6
–12
12
–14
14
–24
24
45
75
45
80
±20
±20
25°C
±15
±15
±100
25°C
±15
25°C
0.7
Full range
25°C
±150
Full range
mV
µA
ppm/°C
±15
1.5
0.7
2
2.5
75
80
25°C
UNIT
V
25°C
Full range
IZ,min < IZ < 1 mA
MIN
Full range
25°C
IZ = 1 mA
LM4041D12I
MAX
1.225
Full range
IZ = 100 µA
∆VZ/∆IZ
LM4041C12I
MIN
25°C
IZ = 10 mA
Reverse breakdown
voltage change with
cathode current change
TA
6
2
2.5
2.5
8
8
mV
10
ZZ
Reverse dynamic
impedance
IZ = 1 mA, f = 120 Hz,
IAC = 0.1 IZ
25°C
0.5
eN
Wideband noise
IZ = 100 µA,
10 Hz ≤ f ≤ 10 kHz
25°C
20
20
µVRMS
Long-term stability of
reverse breakdown
voltage
t = 1000 h,
TA = 25°C ± 0.1°C,
IZ = 100 µA
25°C
120
120
ppm
6
Submit Documentation Feedback
1.5
0.5
2
Ω
LM4041
PRECISION MICROPOWER SHUNT VOLTAGE REFERENCE
www.ti.com
SLCS146E – FEBRUARY 2005 – REVISED FEBRUARY 2006
LM4041x12Q Electrical Characteristics
full-range TA = –40°C to 125°C (unless otherwise noted)
PARAMETER
VZ
TEST CONDITIONS
Reverse breakdown
voltage
IZ = 100 µA
Reverse breakdown
voltage tolerance
IZ = 100 µA
IZ,min
Minimum cathode
current
αVZ
Average temperature
coefficient of reverse
breakdown voltage
25°C
Full range
TYP
1 mA < IZ < 12 mA
TYP
MAX
1.225
6
–12
12
18.4
–31
31
45
75
45
80
±20
±20
25°C
±15
±15
±100
25°C
±15
25°C
0.7
Full range
25°C
Full range
25°C
±150
mV
µA
ppm/°C
±15
1.5
0.7
2
2.5
75
80
25°C
UNIT
V
–6
Full range
IZ,min < IZ < 1 mA
MIN
–18.4
25°C
IZ = 1 mA
LM4041D12Q
MAX
1.225
Full range
IZ = 100 µA
∆VZ/∆IZ
LM4041C12Q
MIN
25°C
IZ = 10 mA
Reverse breakdown
voltage change with
cathode current change
TA
6
2.5
2.5
8
0.5
2
8
mV
10
0.5
ZZ
Reverse dynamic
impedance
IZ = 1 mA, f = 120 Hz,
IAC = 0.1 IZ
eN
Wideband noise
IZ = 100 µA,
10 Hz ≤ f ≤ 10 kHz
25°C
20
20
µVRMS
Long-term stability of
reverse breakdown
voltage
t = 1000 h,
TA = 25°C ± 0.1°C,
IZ = 100 µA
25°C
120
120
ppm
Full range
Submit Documentation Feedback
1.5
2
Ω
7
LM4041
PRECISION MICROPOWER SHUNT VOLTAGE REFERENCE
www.ti.com
SLCS146E – FEBRUARY 2005 – REVISED FEBRUARY 2006
LM4041xI (Adjustable Version) Electrical Characteristics
full-range TA = –40°C to 85°C (unless otherwise noted)
PARAMETER
VREF
TEST CONDITIONS
Reference voltage
IZ = 100 µA, VZ = 5 V
Reference voltage
tolerance (1)
IZ = 100 µA, VZ = 5 V
IZ,min
Minimum cathode
current
∆VREF/∆IZ
Reference voltage
change with cathode
current change
∆VREF/∆VKA
Reference voltage
change with output
voltage change
IFB
Feedback current
αVREF
Average temperature
coefficient of
reference voltage (1)
eN
(1)
8
LM4041BI
MIN
25°C
TYP
1 mA < IZ < 12 mA
MAX
1.233
–2.5
2.5
–6.2
6.2
10.5
–14
14
45
25°C
0.7
1.5
2
4
–1.55
–2
0.7
2
4
–1.55
–2
100
–2.5
60
120
25°C
±20
25°C
±15
100
120
mV
mV/V
nA
±20
±15
±100
Full range
µA
6
–2.5
60
mV
1.5
2
6
Full range
75
80
2
Full range
25°C
45
80
Full range
25°C
75
UNIT
V
–10.5
Full range
IZ = 1 mA, VZ = 5 V
TYP
25°C
25°C
IZ = 1 mA
MIN
Full range
Full range
IZ,min < IZ < 1 mA
LM4041CI
MAX
1.233
25°C
IZ = 10 mA, VZ = 5 V
ZZ
TA
±100
ppm/°C
IZ = 100 µA, VZ = 5 V
25°C
±15
±15
IZ = 1 mA, f = 120 Hz,
IAC = 0.1 IZ, VZ = VREF
25°C
0.3
0.3
IZ = 1 mA, f = 120 Hz,
IAC = 0.1 IZ, VZ = 10 V
25°C
2
2
Wideband noise
IZ = 100 µA, VZ = VREF,
10 Hz ≤ f ≤ 10 kHz
25°C
20
20
µVRMS
Long-term stability of
reverse breakdown
voltage
t = 1000 h,
TA = 25°C ± 0.1°C,
IZ = 100 µA
25°C
120
120
ppm
Reverse dynamic
impedance
Ω
Reference voltage tolerance and average temperature coefficient change with output voltage (VZ). See Typical Characteristics.
Submit Documentation Feedback
LM4041
PRECISION MICROPOWER SHUNT VOLTAGE REFERENCE
www.ti.com
SLCS146E – FEBRUARY 2005 – REVISED FEBRUARY 2006
LM4041xI (Adjustable Version) Electrical Characteristics
full-range TA = –40°C to 85°C (unless otherwise noted)
PARAMETER
VREF
IZ,min
∆VREF/∆IZ
TEST CONDITIONS
Reference voltage
IZ = 100 µA, VZ = 5 V
Reference voltage tolerance (1)
IZ = 100 µA, VZ = 5 V
Reference voltage change
with output voltage change
IFB
Feedback current
IZ,min < IZ < 1 mA
IZ = 1 mA
ZZ
eN
(1)
Average temperature coefficient
of reference voltage (1)
25°C
–12
12
–24
24
45
25°C
25°C
0.7
mV
µA
2
2.5
2
6
–1.55
–2
Full range
25°C
75
80
Full range
UNIT
V
Full range
mV
8
Full range
25°C
IZ = 1 mA, VZ = 5 V
MAX
1.233
–3
60
Full range
IZ = 10 mA, VZ = 5 V
αVREF
TYP
Full range
1 mA < IZ < 12 mA
∆VREF/∆VKA
LM4041DI
MIN
25°C
25°C
Minimum cathode current
Reference voltage change
with cathode current change
TA
150
200
25°C
±20
25°C
±15
±150
Full range
mV/V
nA
ppm/°C
IZ = 100 µA, VZ = 5 V
25°C
±15
IZ = 1 mA, f = 120 Hz,
IAC = 0.1 IZ, VZ = VREF
25°C
0.3
IZ = 1 mA, f = 120 Hz,
IAC = 0.1 IZ, VZ = 10 V
25°C
2
Wideband noise
IZ = 100 µA, VZ = VREF,
10 Hz ≤ f ≤ 10 kHz
25°C
20
µVRMS
Long-term stability
of reverse breakdown voltage
t = 1000 h,
TA = 25°C ± 0.1°C,
IZ = 100 µA
25°C
120
ppm
Reverse dynamic impedance
Ω
Reference voltage tolerance and average temperature coefficient change with output voltage (VZ). See Typical Characteristics.
Submit Documentation Feedback
9
LM4041
PRECISION MICROPOWER SHUNT VOLTAGE REFERENCE
www.ti.com
SLCS146E – FEBRUARY 2005 – REVISED FEBRUARY 2006
LM4041xQ (Adjustable Version) Electrical Characteristics
full-range TA = –40°C to 125°C (unless otherwise noted)
PARAMETER
VREF
TEST CONDITIONS
Reference voltage
IZ = 100 µA, VZ = 5 V
Reference voltage
tolerance (1)
IZ = 100 µA, VZ = 5 V
IZ,min
Minimum cathode
current
∆VREF/∆IZ
Reference voltage
change with cathode
current change
∆VREF/∆VKA
Reference voltage
change with output
voltage change
IFB
Feedback current
αVREF
Average temperature
coefficient of
reference voltage (1)
eN
(1)
10
LM4041CQ
MIN
25°C
TYP
1 mA < IZ < 12 mA
MAX
1.233
6.2
–12
12
–18
18
–30
30
45
25°C
0.7
1.5
2
4
–1.55
–2
0.7
2
6
–1.55
–2.5
100
–4
60
120
25°C
±20
25°C
±15
150
200
mV
mV/V
nA
±20
±15
±100
Full range
µA
10
–3
60
mV
2
2.5
8
Full range
75
80
2
Full range
25°C
45
80
Full range
25°C
75
UNIT
V
–6.2
Full range
IZ = 1 mA, VZ = 5 V
TYP
25°C
25°C
IZ = 1 mA
MIN
Full range
Full range
IZ,min < IZ < 1 mA
LM4041DQ
MAX
1.233
25°C
IZ = 10 mA, VZ = 5 V
ZZ
TA
±150
ppm/°C
IZ = 100 µA, VZ = 5 V
25°C
±15
±15
IZ = 1 mA, f = 120 Hz,
IAC = 0.1 IZ, VZ = VREF
25°C
0.3
0.3
IZ = 1 mA, f = 120 Hz,
IAC = 0.1 IZ, VZ = 10 V
25°C
2
2
Wideband noise
IZ = 100 µA, VZ = VREF,
10 Hz ≤ f ≤ 10 kHz
25°C
20
20
µVRMS
Long-term stability of
reverse breakdown
voltage
t = 1000 h,
TA = 25°C ± 0.1°C,
IZ = 100 µA
25°C
120
120
ppm
Reverse dynamic
impedance
Ω
Reference voltage tolerance and average temperature coefficient change with output voltage (VZ). See Typical Characteristics.
Submit Documentation Feedback
LM4041
PRECISION MICROPOWER SHUNT VOLTAGE REFERENCE
www.ti.com
SLCS146E – FEBRUARY 2005 – REVISED FEBRUARY 2006
TYPICAL CHARACTERISTICS
0.5
1000
IZ = 150 A
VREF = 1.2 V
0.4
0.3
800
Noise Voltage (nV/Hz)
Reference Voltage (V)
−9.9 ppm/C
0.2
2.7 ppm/C
0.1
0
−0.1
21 ppm/C
−0.2
−0.3
600
400
200
−0.4
−0.5
−40
−20
0
20
40
60
80
0
100
1
10
3
1.235
125C
1.234
0
1
−5
VZ
−10
0.5
VIN (V)
1.5
Reference Voltage (V)
VIN
VZ (V)
LM4041 (Adj)
IZ = 1 mA
10
5
10k
<br/>
1.2345
2
1k
Figure 2. Noise Voltage vs Frequency
15
2.5
100
Frequency (Hz)
Temperature (C)
Figure 1. Temperature Drift for Different Average
Temperature Coefficients
85C
1.2335
−40C
25C
1.233
1.2325
1.232
1.2315
−15
0
−20
26
−0.5
−2
2
6
10
14
18
22
1.231
1.2305
0
4
6
8
10
Reverse (Output) Voltage (V)
Time (s)
Figure 3. Start-Up Characteristics
<br/>
2
Figure 4. Reference Voltage vs Reverse (Output) Voltage
(for Different Temperatures)
Submit Documentation Feedback
11
LM4041
PRECISION MICROPOWER SHUNT VOLTAGE REFERENCE
www.ti.com
SLCS146E – FEBRUARY 2005 – REVISED FEBRUARY 2006
TYPICAL CHARACTERISTICS
1.235
100
LM4041 (Adj)
IZ = 1 mA
1.2345
90
125C
85C
80
VREF
Feedback Current (nA)
Reference Voltage (V)
1.234
LM4041 (Adj)
IZ = 1 mA
1.2335
1.233
5V
1.2325
1.232
1.2315
25C
70
−40C
60
50
40
30
10 V
20
1.231
10
1.2305
−40
−20
0
20
40
60
80
0
100
Temperature (C)
2
4
6
8
10
Reverse (Output) Voltage (V)
Figure 6. Feedback Current vs Reverse (Output) Voltage
(for Different Temperatures)
Figure 5. Reference Voltage vs Temperature
(for Different Reverse Voltages)
1000
1000
LM4041 (Adj)
IZ = 1 mA
IZ = 0.1 IZ
Tj = 25C
100
CL = 0 F
10
10 V
Impedance (Ω)
Capacitor
Line
100
Impedance ()
0
CL = 0 F
Capacitor
Line
LM4041 (Adj)
IZ = 150 A
IZ = 0.1 IZ
Tj = 25°C
10 V
10
5V
5V
CL = 1 F
CL = 1 F
1.23 V
1
1
2.5 V
1.23 V
2.5 V
0.1
0.1
100
1k
10k
100k
1M
100
1k
Frequency (Hz)
100k
Frequency (Hz)
Figure 7. Output Impedance vs Frequency
12
10k
Figure 8. Output Impedance vs Frequency
Submit Documentation Feedback
1M
LM4041
PRECISION MICROPOWER SHUNT VOLTAGE REFERENCE
www.ti.com
SLCS146E – FEBRUARY 2005 – REVISED FEBRUARY 2006
TYPICAL CHARACTERISTICS
FB Steps (V)
(see Figure 12)
0
100
2
4
6
100
8
90
LM4041 (Adj)
VZ = 1.23 V (nominal)
90
80
Reverse Current (A)
Reverse Current (A)
80
70
60
50
40
30
70
60
50
40
30
20
20
LM4041 (Adj)
IZ = 1 mA
10
10
0
0
1
2
3
4
5
6
7
8
9
10
Reverse (Output) Voltage (V)
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
Reverse (Output) Voltage (V)
Figure 10. Reverse Characteristics and Minumum
Operating Current
Figure 9. Reverse Characteristics
<br/>
1.6
0
LM4041 (Adj)
VAdj = VREF + 5 mV
1.4
Output Saturation (V)
1.2
−40C
1
25C
85C
0.8
125C
0.6
0.4
0.2
0
0
1
2
3
4
5
6
7
8
9
10 11
12
Output Current (mA)
Figure 11. Output Saturation vs Output Current
Submit Documentation Feedback
13
LM4041
PRECISION MICROPOWER SHUNT VOLTAGE REFERENCE
www.ti.com
SLCS146E – FEBRUARY 2005 – REVISED FEBRUARY 2006
APPLICATION INFORMATION
RS 30 k
VIN
LM4041-1.2
VZ
1-Hz rate
Figure 12. Startup Characteristics Test Circuit
IR
(+)
LM4041 (Adj)
(−)
2 V/step
V
Figure 13. Reverse Characteristics Test Circuit
Output Capacitor
The LM4041 does not require an output capacitor across CATHODE and ANODE for stability. However, if an
output bypass capacitor is desired, the LM4041 is designed to be stable with all capacitive loads.
SOT-23 and SC-70 Pin Connections
There is a parasitic Schottky diode connected between pins 2 and 3 of the SOT-23 packaged device. Thus, pin 3
of the SOT-23 package must be left floating or connected to pin 2. Similarly, pin 2 of the SC-70 package also
must be left floating or connected to pin 1.
14
Submit Documentation Feedback
LM4041
PRECISION MICROPOWER SHUNT VOLTAGE REFERENCE
www.ti.com
SLCS146E – FEBRUARY 2005 – REVISED FEBRUARY 2006
APPLICATION INFORMATION
Adjustable Version
The adjustable version allows VZ to be set by a user-defined resistor divider. The output voltage, VZ, is set
according to the equation shown in Figure 14.
VS
RS
VREF
LM4041
VZ = VREF 1 R2
R1
+
R1
−
(Adjustable)
R2
Figure 14. Adjustable Shunt Regulator
Cathode and Load Currents
In a typical shunt regulator configuration (see Figure 15), an external resistor, RS, is connected between the
supply and the cathode of the LM4041. RS must be set properly, as it sets the total current available to supply
the load (IL) and bias the LM4041 (IZ). In all cases, IZ must stay within a specified range for proper operation of
the reference. Taking into consideration one extreme in the variation of the load and supply voltage (maximum IL
and minimum VS), RS must be small enough to supply the minimum IZ required for operation of the regulator, as
given by data sheet parameters. At the other extreme, maximum VS and minimum IL, RS must be large enough to
limit IZ to less than its maximum recommended rating of 12 mA.
RS is calculated as shown in Equation 1.
VS VZ
RS (I L I Z)
(1)
VS
RS
IZ + IL
IL
VZ
IZ
LM4041
Figure 15. Shunt Regulator
Submit Documentation Feedback
15
PACKAGE OPTION ADDENDUM
www.ti.com
22-Feb-2016
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM4041A12IDBZR
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4MK3 ~ 4MKU)
LM4041A12IDBZRG4
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4MK3 ~ 4MKU)
LM4041A12IDBZT
ACTIVE
SOT-23
DBZ
3
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4MK3 ~ 4MKU)
LM4041A12IDCKR
ACTIVE
SC70
DCK
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
MKU
LM4041A12ILP
PREVIEW
TO-92
LP
3
1000
TBD
Call TI
Call TI
-40 to 85
LM4041B12IDBZR
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4ML3 ~ 4MLU)
LM4041B12IDBZT
ACTIVE
SOT-23
DBZ
3
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4ML3 ~ 4MLU)
LM4041B12IDCKR
ACTIVE
SC70
DCK
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
MLU
LM4041B12ILP
PREVIEW
TO-92
LP
3
1000
TBD
Call TI
Call TI
-40 to 85
LM4041BIDBZR
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4MG3 ~ 4MGU)
LM4041BIDBZRG4
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4MG3 ~ 4MGU)
LM4041BIDBZT
ACTIVE
SOT-23
DBZ
3
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4MG3 ~ 4MGU)
LM4041BIDBZTG4
ACTIVE
SOT-23
DBZ
3
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4MG3 ~ 4MGU)
LM4041BIDCKR
ACTIVE
SC70
DCK
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
MGU
LM4041BIDCKT
ACTIVE
SC70
DCK
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
MGU
LM4041BILP
PREVIEW
TO-92
LP
3
1000
TBD
Call TI
Call TI
-40 to 85
LM4041BILPR
PREVIEW
TO-92
LP
3
2000
TBD
Call TI
Call TI
-40 to 85
LM4041C12IDBZR
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4MM3 ~ 4MMU)
LM4041C12IDBZRG4
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4MM3 ~ 4MMU)
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
22-Feb-2016
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM4041C12IDBZT
ACTIVE
SOT-23
DBZ
3
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4MM3 ~ 4MMU)
LM4041C12IDBZTG4
ACTIVE
SOT-23
DBZ
3
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4MM3 ~ 4MMU)
LM4041C12IDCKR
ACTIVE
SC70
DCK
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
MMU
LM4041C12IDCKRE4
ACTIVE
SC70
DCK
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
MMU
LM4041C12IDCKRG4
ACTIVE
SC70
DCK
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
MMU
LM4041C12ILP
ACTIVE
TO-92
LP
3
1000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
-40 to 85
NPC12I
LM4041C12ILPE3
ACTIVE
TO-92
LP
3
1000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
-40 to 85
NPC12I
LM4041C12ILPR
ACTIVE
TO-92
LP
3
2000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
-40 to 85
NPC12I
LM4041C12QDBZR
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
(4MS3 ~ 4MSU)
LM4041C12QDBZT
ACTIVE
SOT-23
DBZ
3
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
(4MS3 ~ 4MSU)
LM4041CIDBZR
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4MH3 ~ 4MHU)
LM4041CIDBZRG4
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4MH3 ~ 4MHU)
LM4041CIDBZT
ACTIVE
SOT-23
DBZ
3
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4MH3 ~ 4MHU)
LM4041CIDBZTG4
ACTIVE
SOT-23
DBZ
3
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4MH3 ~ 4MHU)
LM4041CIDCKR
ACTIVE
SC70
DCK
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
MHU
LM4041CIDCKT
ACTIVE
SC70
DCK
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
MHU
LM4041CIDCKTG4
ACTIVE
SC70
DCK
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
MHU
LM4041CILP
ACTIVE
TO-92
LP
3
1000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
-40 to 85
NPCI
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
22-Feb-2016
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM4041CILPE3
ACTIVE
TO-92
LP
3
1000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
-40 to 85
NPCI
LM4041CILPR
ACTIVE
TO-92
LP
3
2000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
-40 to 85
NPCI
LM4041CQDBZR
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
(4MP3 ~ 4MPU)
LM4041CQDBZT
ACTIVE
SOT-23
DBZ
3
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
(4MP3 ~ 4MPU)
LM4041CQDBZTG4
ACTIVE
SOT-23
DBZ
3
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
(4MP3 ~ 4MPU)
LM4041D12IDBZR
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4MN3 ~ 4MNU)
LM4041D12IDBZRG4
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4MN3 ~ 4MNU)
LM4041D12IDBZT
ACTIVE
SOT-23
DBZ
3
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4MN3 ~ 4MNU)
LM4041D12IDBZTG4
ACTIVE
SOT-23
DBZ
3
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4MN3 ~ 4MNU)
LM4041D12IDCKR
ACTIVE
SC70
DCK
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
MNU
LM4041D12ILP
ACTIVE
TO-92
LP
3
1000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
-40 to 85
NPD12I
LM4041D12ILPE3
ACTIVE
TO-92
LP
3
1000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
-40 to 85
NPD12I
LM4041D12ILPR
ACTIVE
TO-92
LP
3
2000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
-40 to 85
NPD12I
LM4041D12QDBZR
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
(4MT3 ~ 4MTU)
LM4041DIDBZR
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4MJ3 ~ 4MJU)
LM4041DIDBZRG4
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4MJ3 ~ 4MJU)
LM4041DIDBZT
ACTIVE
SOT-23
DBZ
3
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4MJ3 ~ 4MJU)
LM4041DIDBZTG4
ACTIVE
SOT-23
DBZ
3
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
(4MJ3 ~ 4MJU)
Addendum-Page 3
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
22-Feb-2016
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM4041DIDCKR
ACTIVE
SC70
DCK
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
MJU
LM4041DIDCKT
ACTIVE
SC70
DCK
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
MJU
LM4041DILP
ACTIVE
TO-92
LP
3
1000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
-40 to 85
NPDI
LM4041DILPR
ACTIVE
TO-92
LP
3
2000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
-40 to 85
NPDI
LM4041DILPRE3
ACTIVE
TO-92
LP
3
2000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
-40 to 85
NPDI
LM4041DQDBZR
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
(4MR3 ~ 4MRU)
LM4041DQDBZRG4
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
(4MR3 ~ 4MRU)
LM4041DQDBZT
ACTIVE
SOT-23
DBZ
3
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
(4MR3 ~ 4MRU)
LM4041DQDBZTG4
ACTIVE
SOT-23
DBZ
3
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
(4MR3 ~ 4MRU)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Addendum-Page 4
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
(4)
22-Feb-2016
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 5
PACKAGE MATERIALS INFORMATION
www.ti.com
8-Mar-2016
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LM4041A12IDCKR
SC70
DCK
5
3000
179.0
8.4
2.2
2.5
1.2
4.0
8.0
Q3
LM4041B12IDCKR
SC70
DCK
5
3000
179.0
8.4
2.2
2.5
1.2
4.0
8.0
Q3
LM4041BIDCKR
SC70
DCK
5
3000
179.0
8.4
2.2
2.5
1.2
4.0
8.0
Q3
LM4041BIDCKT
SC70
DCK
5
250
179.0
8.4
2.2
2.5
1.2
4.0
8.0
Q3
LM4041C12IDCKR
SC70
DCK
5
3000
179.0
8.4
2.2
2.5
1.2
4.0
8.0
Q3
LM4041C12QDBZR
SOT-23
DBZ
3
3000
179.0
8.4
3.15
2.95
1.22
4.0
8.0
Q3
LM4041C12QDBZT
SOT-23
DBZ
3
250
179.0
8.4
3.15
2.95
1.22
4.0
8.0
Q3
LM4041CIDCKR
SC70
DCK
5
3000
179.0
8.4
2.2
2.5
1.2
4.0
8.0
Q3
LM4041CIDCKT
SC70
DCK
5
250
179.0
8.4
2.2
2.5
1.2
4.0
8.0
Q3
LM4041CQDBZR
SOT-23
DBZ
3
3000
179.0
8.4
3.15
2.95
1.22
4.0
8.0
Q3
LM4041CQDBZT
SOT-23
DBZ
3
250
179.0
8.4
3.15
2.95
1.22
4.0
8.0
Q3
LM4041D12IDCKR
SC70
DCK
5
3000
179.0
8.4
2.2
2.5
1.2
4.0
8.0
Q3
LM4041D12QDBZR
SOT-23
DBZ
3
3000
179.0
8.4
3.15
2.95
1.22
4.0
8.0
Q3
LM4041DIDCKR
SC70
DCK
5
3000
179.0
8.4
2.2
2.5
1.2
4.0
8.0
Q3
LM4041DIDCKT
SC70
DCK
5
250
179.0
8.4
2.2
2.5
1.2
4.0
8.0
Q3
LM4041DQDBZR
SOT-23
DBZ
3
3000
179.0
8.4
3.15
2.95
1.22
4.0
8.0
Q3
LM4041DQDBZT
SOT-23
DBZ
3
250
179.0
8.4
3.15
2.95
1.22
4.0
8.0
Q3
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
8-Mar-2016
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM4041A12IDCKR
SC70
DCK
5
3000
203.0
203.0
35.0
LM4041B12IDCKR
SC70
DCK
5
3000
203.0
203.0
35.0
LM4041BIDCKR
SC70
DCK
5
3000
203.0
203.0
35.0
LM4041BIDCKT
SC70
DCK
5
250
203.0
203.0
35.0
LM4041C12IDCKR
SC70
DCK
5
3000
203.0
203.0
35.0
LM4041C12QDBZR
SOT-23
DBZ
3
3000
203.0
203.0
35.0
LM4041C12QDBZT
SOT-23
DBZ
3
250
203.0
203.0
35.0
LM4041CIDCKR
SC70
DCK
5
3000
203.0
203.0
35.0
LM4041CIDCKT
SC70
DCK
5
250
203.0
203.0
35.0
LM4041CQDBZR
SOT-23
DBZ
3
3000
203.0
203.0
35.0
LM4041CQDBZT
SOT-23
DBZ
3
250
203.0
203.0
35.0
LM4041D12IDCKR
SC70
DCK
5
3000
203.0
203.0
35.0
LM4041D12QDBZR
SOT-23
DBZ
3
3000
203.0
203.0
35.0
LM4041DIDCKR
SC70
DCK
5
3000
203.0
203.0
35.0
LM4041DIDCKT
SC70
DCK
5
250
203.0
203.0
35.0
LM4041DQDBZR
SOT-23
DBZ
3
3000
203.0
203.0
35.0
LM4041DQDBZT
SOT-23
DBZ
3
250
203.0
203.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated
Similar pages