TI1 LM61BIZ/NOPB Lm61 2.7v, sot-23 or to-92 temperature sensor Datasheet

LM61
www.ti.com
SNIS121I – JUNE 1999 – REVISED FEBRUARY 2013
LM61 2.7V, SOT-23 or TO-92 Temperature Sensor
Check for Samples: LM61
FEATURES
DESCRIPTION
•
•
•
•
The LM61 is a precision integrated-circuit
temperature sensor that can sense a −30°C to
+100°C temperature range while operating from a
single +2.7V supply. The LM61's output voltage is
linearly proportional to Celsius (Centigrade)
temperature (+10 mV/°C) and has a DC offset of
+600 mV. The offset allows reading negative
temperatures without the need for a negative supply.
The nominal output voltage of the LM61 ranges from
+300 mV to +1600 mV for a −30°C to +100°C
temperature range. The LM61 is calibrated to provide
accuracies of ±2.0°C at room temperature and ±3°C
over the full −25°C to +85°C temperature range.
1
2
Calibrated Linear Scale Factor of +10 mV/°C
Rated for Full −30° to +100°C Range
Suitable for Remote Applications
UL Recognized Component
APPLICATIONS
•
•
•
•
•
•
•
•
•
Cellular Phones
Computers
Power Supply Modules
Battery Management
FAX Machines
Printers
HVAC
Disk Drives
Appliances
The LM61's linear output, +600 mV offset, and factory
calibration simplify external circuitry required in a
single supply environment where reading negative
temperatures is required. Because the LM61's
quiescent current is less than 125 μA, self-heating is
limited to a very low 0.2°C in still air. Shutdown
capability for the LM61 is intrinsic because its
inherent low power consumption allows it to be
powered directly from the output of many logic gates.
Table 1. Key Specifications
VALUE
UNIT
±2.0 or ±3.0
°C (max)
Accuracy for −30°C to +100°C
±4.0
°C (max)
Accuracy for −25°C to +85°C
±3.0
°C (max)
Temperature Slope
+10
mV/°C
Accuracy at 25°C
Power Supply Voltage Range
+2.7 to +10
V
Current Drain @ 25°C
125
µA (max)
Nonlinearity
±0.8
°C (max)
Output Impedance
800
Ω (max)
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1999–2013, Texas Instruments Incorporated
LM61
SNIS121I – JUNE 1999 – REVISED FEBRUARY 2013
www.ti.com
TYPICAL APPLICATION
A.
VO = (+10 mV/°C × T °C) + 600 mV
Figure 1. Full-Range Centigrade Temperature Sensor (−30°C to +100°C) Operating from
a Single Li-Ion Battery Cell
Table 2. Temperature and Typical VO Values of Figure 1
TEMPERATURE (T)
TYPICAL VO
+100°C
+1600 mV
+85°C
+1450 mV
+25°C
+850 mV
0°C
+600 mV
−25°C
+350 mV
−30°C
+300 mV
CONNECTION DIAGRAMS
Figure 2. SOT-23 (Top View)
See Package Number DBZ0003A
Figure 3. TO-92 (Bottom View)
See Package Number LP0003A
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
2
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM61
LM61
www.ti.com
SNIS121I – JUNE 1999 – REVISED FEBRUARY 2013
Absolute Maximum Ratings (1)
Supply Voltage
+12V to −0.2V
Output Voltage
(+VS + 0.6V) to −0.6V
Output Current
10 mA
Input Current at any pin (2)
5 mA
−65°C to +150°C
Storage Temperature
Maximum Junction Temperature (TJMAX)
+125°C
ESD Susceptibility (3)
Human Body Model
2500V
Machine Model
(1)
(2)
(3)
250V
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see
the Electrical Characteristics . The guaranteed specifications apply only for the test conditions listed. Some performance characteristics
may degrade when the device is not operated under the listed test conditions.
When the input voltage (VI) at any pin exceeds power supplies (VI < GND or VI > +VS), the current at that pin should be limited to 5 mA.
The human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin. The machine model is a 200 pF
capacitor discharged directly into each pin.
Operating Ratings (1)
TMIN ≤ TA ≤ TMAX
Specified Temperature Range:
LM61C
−30°C ≤ TA ≤ +100°C
LM61B
−25°C ≤ TA ≤ +85°C
Supply Voltage Range (+VS)
+2.7V to +10V
Thermal Resistance, θJA (2)
SOT-23
TO-92
450°C/W
180°C/W
Soldering process must comply with Reflow Temperature Profile specifications. Refer to http://www.ti.com/packaging. (3)
(1)
(2)
(3)
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see
the Electrical Characteristics . The guaranteed specifications apply only for the test conditions listed. Some performance characteristics
may degrade when the device is not operated under the listed test conditions.
The junction to ambient thermal resistance (θJA) is specified without a heat sink in still air.
Reflow temperature profiles are different for lead-free and non-lead-free packages.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM61
3
LM61
SNIS121I – JUNE 1999 – REVISED FEBRUARY 2013
www.ti.com
Electrical Characteristics
Unless otherwise noted, these specifications apply for +VS = +3.0 VDC. Boldface limits apply for TA = TJ = TMIN to TMAX ; all
other limits TA = TJ = 25°C.
PARAMETER
Accuracy
TEST CONDITIONS
TYPICAL (1)
(3)
Output Voltage at 0°C
Nonlinearity
Sensor Gain (Average Slope)
Line Regulation
(5)
+10
Change of Quiescent Current
Long Term Stability
(1)
(2)
(3)
(4)
(5)
(6)
4
±2.0
±3.0
°C (max)
±3.0
±4.0
°C (max)
±0.6
±0.8
°C (max)
mV
+9.7
+9.6
mV/°C (min)
+10.4
mV/°C (max)
+3.0V ≤ +VS ≤ +10V
−30°C ≤ TA ≤ +85°C, +VS= +2.7V
+85°C ≤ TA ≤ +100°C, +VS= +2.7V
0.8
2.3
5
0.8
2.3
5
kΩ (max)
kΩ (max)
kΩ (max)
+3.0V ≤ +VS ≤ +10V
±0.7
±0.7
mV/V (max)
+2.7V ≤ +VS ≤ +3.3V
±5.7
±5.7
mV (max)
125
125
µA (max)
155
155
µA (max)
82
+2.7V ≤ +VS ≤ +10V
Temperature Coefficient of
Quiescent Current
(6)
UNITS
(LIMIT)
+10.3
+2.7V ≤ +VS ≤ +10V
Quiescent Current
LM61C
LIMITS (2)
+600
(4)
Output Impedance
LM61B
LIMITS (2)
TJ=TMAX=+100°C, for 1000 hours
±5
μA
0.2
µA/°C
±0.2
°C
Typicals are at TJ = TA = 25°C and represent most likely parametric norm.
Limits are guaranteed to TI's AOQL (Average Outgoing Quality Level).
Accuracy is defined as the error between the output voltage and +10 mV/°C times the device's case temperature plus 600 mV, at
specified conditions of voltage, current, and temperature (expressed in °C).
Nonlinearity is defined as the deviation of the output-voltage-versus-temperature curve from the best-fit straight line, over the device's
rated temperature range.
Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output due to heating
effects can be computed by multiplying the internal dissipation by the thermal resistance.
For best long-term stability, any precision circuit will give best results if the unit is aged at a warm temperature, and/or temperature
cycled for at least 46 hours before long-term life test begins. This is especially true when a small (Surface-Mount) part is wave-soldered;
allow time for stress relaxation to occur. The majority of the drift will occur in the first 1000 hours at elevated temperatures. The drift after
1000 hours will not continue at the first 1000 hour rate.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM61
LM61
www.ti.com
SNIS121I – JUNE 1999 – REVISED FEBRUARY 2013
Typical Performance Characteristics
The LM61 in the SOT-23 package mounted to a printed circuit board as shown in Figure 14 was used to generate the
following thermal curves.
Thermal Resistance
Junction to Air
Thermal Time Constant
Figure 4.
Figure 5.
Thermal Response in
Still Air with Heat Sink
Thermal Response
in Stirred Oil Bath
with Heat Sink
Figure 6.
Figure 7.
Thermal Response in Still
Air without a Heat Sink
Quiescent Current
vs. Temperature
Figure 8.
Figure 9.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM61
5
LM61
SNIS121I – JUNE 1999 – REVISED FEBRUARY 2013
www.ti.com
Typical Performance Characteristics (continued)
The LM61 in the SOT-23 package mounted to a printed circuit board as shown in Figure 14 was used to generate the
following thermal curves.
Accuracy
vs
Temperature
Noise Voltage
Figure 10.
Figure 11.
Supply Voltage
vs Supply Current
Start-Up Response
Figure 12.
Figure 13.
A. ½″ Square Printed Circuit Board with 2 oz. Copper Foil or Similar.
Figure 14. Printed Circuit Board Used for Heat Sink to Generate All Curves
6
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM61
LM61
www.ti.com
SNIS121I – JUNE 1999 – REVISED FEBRUARY 2013
APPLICATION INFORMATION
Mounting
The LM61 can be applied easily in the same way as other integrated-circuit temperature sensors. It can be glued
or cemented to a surface. The temperature that the LM61 is sensing will be within about +0.2°C of the surface
temperature that LM61's leads are attached to.
This presumes that the ambient air temperature is almost the same as the surface temperature; if the air
temperature were much higher or lower than the surface temperature, the actual temperature measured would
be at an intermediate temperature between the surface temperature and the air temperature.
To ensure good thermal conductivity the backside of the LM61 die is directly attached to the GND pin. The lands
and traces to the LM61 will, of course, be part of the printed circuit board, which is the object whose temperature
is being measured.
Alternatively, the LM61 can be mounted inside a sealed-end metal tube, and can then be dipped into a bath or
screwed into a threaded hole in a tank. As with any IC, the LM61 and accompanying wiring and circuits must be
kept insulated and dry, to avoid leakage and corrosion. This is especially true if the circuit may operate at cold
temperatures where condensation can occur. Printed-circuit coatings and varnishes such as Humiseal and epoxy
paints or dips are often used to ensure that moisture cannot corrode the LM61 or its connections.
The thermal resistance junction to ambient (θJA) is the parameter used to calculate the rise of a device junction
temperature due to its power dissipation. For the LM61, Equation 1 is used to calculate the rise in the die
temperature.
TJ = TA + θJA [(+VS IQ) + (+VS − VO) IL]
where
•
•
IQ is the quiescent current
ILis the load current on the output
(1)
Since the LM61's junction temperature is the actual temperature being measured care should be taken to
minimize the load current that the LM61 is required to drive.
Table 3 summarizes the rise in die temperature of the LM61 without any loading with a 3.3V supply, and the
thermal resistance for different conditions.
Table 3. Temperature Rise of LM61 Due to Self-Heating and Thermal Resistance (θJA)
Still air
SOT-23 (1)
SOT-23 (2)
NO HEAT SINK
SMALL HEAT FIN
TO-92 (3)
NO HEAT SINK
SMALL HEAT FIN
θJA
(°C/W)
TJ − TA
(°C)
θJA
(°C/W)
TJ − TA
(°C)
θJA
(°C/W)
TJ − TA
(°C)
θJA
(°C/W)
TJ − TA
(°C)
450
0.26
260
0.13
180
0.09
140
0.07
180
0.09
90
0.05
70
0.03
Moving air
(1)
(2)
(3)
TO-92 (1)
Part soldered to 30 gauge wire.
Heat sink used is ½″ square printed circuit board with 2 oz. foil with part attached as shown in Figure 14.
Part glued and leads soldered to 1" square of 1/16" printed circuit board with 2oz. foil or similar.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM61
7
LM61
SNIS121I – JUNE 1999 – REVISED FEBRUARY 2013
www.ti.com
Capacitive Loads
The LM61 handles capacitive loading well. Without any special precautions, the LM61 can drive any capacitive
load as shown in Figure 15. Over the specified temperature range the LM61 has a maximum output impedance
of 5 kΩ. In an extremely noisy environment it may be necessary to add some filtering to minimize noise pickup. It
is recommended that 0.1 μF be added from +VS to GND to bypass the power supply voltage, as shown in
Figure 16. In a noisy environment it may be necessary to add a capacitor from the output to ground. A 1 μF
output capacitor with the 5 kΩ maximum output impedance will form a 32 Hz lowpass filter. Since the thermal
time constant of the LM61 is much slower than the 5 ms time constant formed by the RC, the overall response
time of the LM61 will not be significantly affected. For much larger capacitors this additional time lag will increase
the overall response time of the LM61.
Figure 15. LM61 No Decoupling Required for Capacitive Load
Figure 16. LM61 with Filter for Noisy Environment
Figure 17. Simplified Schematic
8
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM61
LM61
www.ti.com
SNIS121I – JUNE 1999 – REVISED FEBRUARY 2013
Applications Circuits
V+
VTEMP
R3
VT1
R4
VT2
4.1V
LM4040
V+
VT
R1
U3
0.1 PF
LM61
R2
(Low = overtemp alarm)
+
U1
-
VOUT
VOUT
LM7211
VTemp
U2
VT1 =
(4.1)R2
R2 + R1||R3
VT2 =
(4.1)R2||R3
R1 + R2||R3
Figure 18. Centigrade Thermostat
Figure 19. Conserving Power Dissipation with Shutdown
Recommended Solder Pads for SOT-23 Package
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM61
9
LM61
SNIS121I – JUNE 1999 – REVISED FEBRUARY 2013
www.ti.com
REVISION HISTORY
Changes from Revision H (February 2013) to Revision I
•
10
Page
Changed layout of National Data Sheet to TI format ............................................................................................................ 9
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM61
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM61BIM3
NRND
SOT-23
DBZ
3
1000
TBD
Call TI
Call TI
-25 to 85
T1B
LM61BIM3/NOPB
ACTIVE
SOT-23
DBZ
3
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-25 to 85
T1B
LM61BIM3X/NOPB
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-25 to 85
T1B
LM61BIZ/LFT3
ACTIVE
TO-92
LP
3
2000
Green (RoHS
& no Sb/Br)
SN | CU SN
N / A for Pkg Type
LM61BIZ/NOPB
ACTIVE
TO-92
LP
3
1800
Green (RoHS
& no Sb/Br)
SN | CU SN
N / A for Pkg Type
-25 to 85
LM61
BIZ
LM61
BIZ
LM61CIM3
NRND
SOT-23
DBZ
3
1000
TBD
Call TI
Call TI
-30 to 100
T1C
LM61CIM3/NOPB
ACTIVE
SOT-23
DBZ
3
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-30 to 100
T1C
LM61CIM3X
NRND
SOT-23
DBZ
3
3000
TBD
Call TI
Call TI
-30 to 100
T1C
LM61CIM3X/NOPB
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-30 to 100
T1C
LM61CIZ/LFT2
ACTIVE
TO-92
LP
3
2000
Green (RoHS
& no Sb/Br)
SN | CU SN
N / A for Pkg Type
LM61CIZ/NOPB
ACTIVE
TO-92
LP
3
1800
Green (RoHS
& no Sb/Br)
SN | CU SN
N / A for Pkg Type
LM61
CIZ
-30 to 100
LM61
CIZ
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
LM61BIM3
SOT-23
DBZ
3
1000
178.0
8.4
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
3.3
2.9
1.22
4.0
8.0
Q3
LM61BIM3/NOPB
SOT-23
DBZ
3
1000
178.0
8.4
3.3
2.9
1.22
4.0
8.0
Q3
LM61BIM3X/NOPB
SOT-23
DBZ
3
3000
178.0
8.4
3.3
2.9
1.22
4.0
8.0
Q3
LM61CIM3
SOT-23
DBZ
3
1000
178.0
8.4
3.3
2.9
1.22
4.0
8.0
Q3
LM61CIM3/NOPB
SOT-23
DBZ
3
1000
178.0
8.4
3.3
2.9
1.22
4.0
8.0
Q3
LM61CIM3X
SOT-23
DBZ
3
3000
178.0
8.4
3.3
2.9
1.22
4.0
8.0
Q3
LM61CIM3X/NOPB
SOT-23
DBZ
3
3000
178.0
8.4
3.3
2.9
1.22
4.0
8.0
Q3
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM61BIM3
SOT-23
DBZ
3
1000
210.0
185.0
35.0
LM61BIM3/NOPB
SOT-23
DBZ
3
1000
210.0
185.0
35.0
LM61BIM3X/NOPB
SOT-23
DBZ
3
3000
210.0
185.0
35.0
LM61CIM3
SOT-23
DBZ
3
1000
210.0
185.0
35.0
LM61CIM3/NOPB
SOT-23
DBZ
3
1000
210.0
185.0
35.0
LM61CIM3X
SOT-23
DBZ
3
3000
210.0
185.0
35.0
LM61CIM3X/NOPB
SOT-23
DBZ
3
3000
210.0
185.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
Similar pages