NSC LM6584MTX Tft-lcd quad, 13v rrio high output current Datasheet

LM6584
TFT-LCD Quad, 13V RRIO High Output Current
Operational Amplifier
General Description
Features
The LM6584 is a low power, high voltage, rail-to-rail inputoutput amplifier ideally suited for LCD panel VCOM driver and
gamma buffer applications. The LM6584 contains four unity
gain stable amplifiers in one package. It provides a common
mode input ability of 0.5V beyond the supply rails, as well as
an output voltage range that extends to within 50mV of either
supply rail. With these capabilities, the LM6584 provides
maximum dynamic range at any supply voltage. Operating
on supplies ranging from 5V to 13V, while consuming only
750µA per amplifier, the LM6584 has a bandwidth of 24MHz
(−3dB).
The LM6584 also features fast slewing and settling times,
along with a high continuous output capability of 75mA. This
output stage is capable of delivering approximately 310mA
peak currents in order to charge or discharge capacitive
loads. These features are ideal for use in TFT-LCDs.
The LM6584 is available in the industry standard 14-pin SO
package and in the space-saving 14-pin TSSOP package.
The amplifiers are specified for operation over the full −40˚C
to +85˚C temperature range.
(VS = 5V, TA = 25˚C typical values unless specified)
n Input common mode voltage
0.5V beyond rails
n Output voltage swing (RL = 2kΩ)
50mV from rails
n Output short circuit current
+310/−410mA
n Continuous output current
75mA
n Supply current (per amp, no load)
750µA
n Supply voltage range
5V to 13V
n Unity gain stable
n −3dB bandwidth (AV = +1)
24MHz
n Slew rate
11V/µSec
n Settling time
270ns
n SO-14 and TSSOP-14 package
n Manufactured in National Semiconductor’s
state-of-the-art bonded wafer, trench isolated
complementary bipolar VIP10™ technology for high
performance at low power levels
Applications
n LCD panel VCOM driver
n LCD panel gamma buffer
n LCD panel repair amp
Test Circuit Diagram
20059201
© 2005 National Semiconductor Corporation
DS200592
www.national.com
LM6584 TFT-LCD Quad, 13V RRIO High Output Current Operational Amplifier
March 2005
LM6584
Absolute Maximum Ratings (Note 1)
Input Common Mode Voltage
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Junction Temperature (Note 4)
Temperature Range
200V
Supply Voltage (V+ - V−)
14V
Differential Input Voltage
± 5.5V
Output Short Circuit to Ground (Note 3)
Storage Temperature Range
5V ≤ VS ≤ 13V
Supply Voltage
2KV
Machine Model
150˚C
Operating Ratings (Note 1)
ESD Tolerance (Note 2)
Human Body Model
V− to V+
−40˚C to +85˚C
Thermal Resistance (θJA)
Continuous
SOIC-14
145˚C/W
TSSOP-14
155˚C/W
−65˚C to 150˚C
13V DC Electrical Characteristics
(Note 13)
Unless otherwise specified, all limits guaranteed for at TJ = 25˚C, VCM = 1⁄2VS and RL = 2kΩ. Boldface limits apply at the temperature extremes.
Symbol
Parameter
VOS
Input Offset Voltage
TC VOS
Input Offset Voltage Average
Drift
IB
Input Bias Current
IOS
Input Offset Current
RIN
Input Resistance
CMRR
Common Mode Rejection
Ratio
Conditions
Min
(Note 6)
Typ
(Note 5)
Max
(Note 6)
0.7
4
6
5
±1
±7
16
150
300
20
Differential Mode
0.5
VCM = 0 to +13V
75
70
103
VCM = 0 to 11.5V
78
72
103
75
70
103
PSRR
Power Supply Rejection Ratio
VCM = ± 1V
CMVR
Input Common-Mode Voltage
Range
CMRR > 50dB
AV
Large Signal Voltage Gain
(Note 7)
RL = 2kΩ, VO = 0.5 to +12.5V
VO
Output Swing High
RL = 2kΩ
Output Swing Low
RL = 2kΩ
Output Short Circuit Current
(Note 11)
Sourcing
200
320
Sinking
200
420
Continuous Output Current
(Note 12)
Sourcing
75
Sinking
75
ISC
ICONT
IS
13.2
0
13
78
72
108
12.85
12.7
12.9
µA
nA
MΩ
dB
dB
−0.2
V
dB
V
0.55
Supply Current (per Amp)
mV
µV/˚C
−0.3/+0.3
Common Mode
Units
780
0.150
mA
mA
1100
1350
µA
13V AC Electrical Characteristics
(Note 13)
Unless otherwise specified, all limits guaranteed for at TJ = 25˚C, VCM = 1⁄2VS and RL = 2kΩ. Boldface limits apply at the temperature extremes.
Symbol
SR
Parameter
Slew Rate (Note 9)
www.national.com
Conditions
AV = +1, VIN = 10VPP
2
Min
(Note 6)
Typ
(Note 5)
8
15
Max
(Note 6)
Units
V/µs
(Note 13) (Continued)
Unless otherwise specified, all limits guaranteed for at TJ = 25˚C, VCM = 1⁄2VS and RL = 2kΩ. Boldface limits apply at the temperature extremes.
Symbol
Parameter
Conditions
Min
(Note 6)
Unity Gain Bandwidth Product
−3dB Frequency
AV = +1
Typ
(Note 5)
Phase Margin
ts
Settling Time (0.1%)
AV = −1, AO = ± 5V, RL = 500Ω
Units
15.4
MHz
10
Φm
Max
(Note 6)
24
MHz
61
deg
780
ns
tp
Propagation Delay
AV = −2, VIN = ± 5V, RL = 500Ω
20
ns
HD2
2nd Harmonic Distortion
FIN = 1MHz (Note 10)
VOUT = 2VPP
−53
dBc
HD3
3rd Harmonic Distortion
FIN = 1MHz (Note 10)
VOUT = 2VPP
−40
dBc
en
Input-Referred Voltage Noise
f = 10kHz
23
nV/
5V DC Electrical Characteristics
(Note 13)
Unless otherwise specified, all limits guaranteed for at TJ = 25˚C, VCM = 1⁄2VS and RL = 2kΩ. Boldface limits apply at the temperature extremes.
Symbol
Parameter
Conditions
Min
(Note 6)
Typ
(Note 5)
Max
(Note 6)
4
6
VOS
Input Offset Voltage
0.7
TC VOS
Input Offset Voltage Average
Drift
10
IB
Input Bias Current
IOS
Input Offset Current
RIN
Input Resistance
CMRR
Common Mode Rejection
Ratio
µA
20
150
300
nA
20
Differential Mode
0.5
VCM Stepped from 0 to 5V
72
68
105
VCM Stepped from 0 to 3.5V
75
70
105
75
70
92
Power Supply Rejection Ratio
VS = VCC = 3.5V to 5.5V
CMVR
Input Common-Mode Voltage
Range
CMRR > 50dB
AV
Large Signal Voltage Gain
(Note 7)
RL = 2kΩ, VO = 0 to 5V
VO
Output Swing High
RL = 2kΩ
Output Swing Low
RL = 2kΩ
0.2
Output Short Circuit Current
(Note 11)
Sourcing
310
Sinking
400
Continuous Output Current
(Note 12)
Sourcing
75
Sinking
75
ICONT
IS
Supply Current (per Amp)
0.0
5.0
MΩ
dB
dB
−0.2
70
65
106
4.85
4.7
4.9
V
dB
V
750
3
µV/˚C
±1
±7
PSRR
ISC
mV
−0.3/+0.3
Common Mode
5.2
Units
0.15
mA
mA
1000
1250
µA
www.national.com
LM6584
13V AC Electrical Characteristics
LM6584
5V AC Electrical Characteristics
(Note 13)
Unless otherwise specified, all limits guaranteed for at TJ = 25˚C, VCM = 1⁄2VS and RL = 2kΩ. Boldface limits apply at the temperature extremes.
Symbol
SR
Parameter
Slew Rate (Note 9)
Conditions
Min
(Note 6)
Typ
(Note 5)
AV = +1, VIN = 3.5VPP
Units
11
V/µs
15.3
MHz
AV = +1
24
MHz
56
deg
Unity Gain Bandwidth Product
−3dB Frequency
Max
(Note 6)
Φm
Phase Margin
ts
Settling Time (0.1%)
AV = −1, VO = ± 1V, RL = 500Ω
270
ns
tp
Propagation Delay
AV = −2, VIN = ± 1V, RL = 500Ω
21
ns
HD2
2nd Harmonic Distortion
FIN = 1MHz (Note 10)
VOUT = 2VPP
−53
dBc
HD3
3rd Harmonic Distortion
FIN = 1MHz (Note 10)
VOUT = 2VPP
−40
dBc
en
Input-Referred Voltage Noise
f = 10kHz
23
nV/
Note 1: Note 1: Absolute maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the
device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical
Characteristics.
Note 2: For testing purposes, ESD was applied using human body model, 1.5kΩ in series with 100pF.
Note 3: Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the
maximum allowed junction temperature of 150˚C
Note 4: The maximum power dissipation is a function of TJ(MAX), θJA, and TA. The maximum allowable power dissipation at any ambient temperature is
PD = (TJ(MAX) - TA)/ θJA . All numbers apply for packages soldered directly onto a PC board.
Note 5: Typical values represent the most likely parametric norm.
Note 6: All limits are guaranteed by testing or statistical analysis.
Note 7: Large signal voltage gain is the total output swing divided by the input signal required to produce that swing.
Note 8: The open loop output current is guaranteed, by the measurement of the open loop output voltage swing.
Note 9: Slew Rate is the average of the raising and falling slew rates.
Note 10: Harmonics are measured with AV = +2 and RL = 100Ω and VIN = 1VPP to give VOUT = 2VPP.
Note 11: Continuous operation at these output currents will exceed the power dissipation ability of the device
Note 12: Power dissipation limits may be exceeded if all four amplifiers source or sink 75mA. Voltage across the output transistors and their output currents must
be taken into account to determine the power dissipation of the device
Note 13: Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating
of the device such that TJ = TA. No guarantee of parametric performance is indicated in the electrical tables under conditions of internal self heating where TJ > TA.
See applications section for information on temperature de-rating of this device.
Connection Diagram
14-Pin SOIC/TSSOP
20059202
Top View
Ordering Information
Package
14-Pin SOIC
14-Pin TSSOP
www.national.com
Part Number
LM6584MA
LM6584MAX
LM6584MT
LM6584MTX
Package Marking
Transport Media
95 Units/Rail
LM6584MA
2.5k Units Tape and Reel
95 Units/Rail
LM6584MT
2.5k Units Tape and Reel
4
NSC Drawing
M14A
MTC14
Unless otherwise specified, all limits guaranteed for TJ = 25˚C,
Gain Phase vs. Temperature
Gain Phase vs. Temperature
20059203
20059204
Gain Phase vs. Capacitive Loading
Gain Phase vs. Capacitive Loading
20059206
20059205
PSRR
PSRR
20059207
20059208
5
www.national.com
LM6584
Typical Performance Characteristics
VCM = 1/2VS and RL = 2kΩ.
LM6584
Typical Performance Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25˚C,
VCM = 1/2VS and RL = 2kΩ. (Continued)
CMRR
CMRR
20059209
20059210
Settling Time vs. Input Step Amplitude
(Output Slew and Settle Time)
Settling Time vs. Capacitive Loading
(Output Slew and Settle Time)
20059212
20059211
Crosstalk Rejection vs. Frequency
(Output to Output)
Input Voltage Noise vs. Frequency
20059213
www.national.com
20059214
6
Stability vs. Capacitive Load Unity Gain, VS = 13V
Large Signal Step Response
20059216
20059215
Small Signal Step Response
Small Signal Step Response
20059217
20059218
Closed Loop Output Impedance vs. Frequency
ISUPPLY vs. Common Mode Voltage
20059220
20059219
7
www.national.com
LM6584
Typical Performance Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25˚C,
VCM = 1/2VS and RL = 2kΩ. (Continued)
LM6584
Typical Performance Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25˚C,
VCM = 1/2VS and RL = 2kΩ. (Continued)
VOS vs. Common Mode Voltage
VOS vs. VOUT (Typical Unit)
20059221
20059222
+
−
VOUT from V vs. ISOURCE
VOUT from V vs. ISINK
20059223
20059224
ISUPPLY vs. Supply Voltage
20059225
www.national.com
8
Output Power
CIRCUIT DESCRIPTION
GENERAL & SPEC
Because of the increased output drive capability, internal
heat dissipation must be held to a level that does not increase the junction temperature above its maximum rated
value of 150˚ C.
The LM6584 is a bipolar process operational amplifier. It has
an exceptional output current capability of 330mA. The part
has both rail to rail inputs and outputs. It has a −3dB bandwidth of 24MHz. The part has input voltage noise of 23nV/
, and 2nd and 3rd harmonic distortion of −53dB and
−40dB respectively.
Power Requirements
The LM6584 operates from a voltage supply, of V+ and
ground, or from a V− and V+ split supply. Single-ended
voltage range is +5V to +13V and split supply range is ± 2.5V
to ± 6.5V.
INPUT SECTION
The LM6584 has rail to rail inputs and thus has an input
range over which the device may be biased of V− minus
0.5V, and V+ plus V. The ultimate limit on input voltage
excursion is the ESD protection diodes on the input pins.
The most important consideration in Rail-to-Rail input op
amps is to understand the input structure. Most Rail-to-Rail
input amps use two differential input pairs to achieve this
function. This is how the LM6584 works. A conventional PNP
differential transistor pair provides the input gain from 0.5V
below the negative rail to about one volt below the positive
rail. At this point internal circuitry activates a differential NPN
transistor pair that allows the part to function from 1 volt
below the positive rail to 0.5V above the positive rail. The
effect on the inputs pins is as if there were two different op
amps connected to the inputs. This has several unique
implications.
• The input offset voltage will change, sometimes from
positive to negative as the inputs transition between the
two stages at about a volt below the positive rail. this
effect is seen in the VOS vs. VCM chart in the Typical
Performance Characteristics section of this datasheet.
• The input bias currents can be either positive or negative.
Do not expect a consistent flow in or out of the pins.
• The part will have different specifications depending on
whether the NPN or PNP stage is operating.
• There is a little more input capacitance then a single
stage input although the ESD diodes often swamp out the
added base capacitance.
• Since the input offset voltages can change from positive
to negative the output may not be monotonic when the
inputs are transitioning between the two stages and the
part is in a high gain configuration.
It should be remembered that swinging the inputs across the
input stage transition may cause output distortion and accuracy anomalies. It is also worth noting that anytime any amps
inputs are swung near the rails THD and other specs are
sure to suffer.
APPLICATION HINTS
POWER SUPPLIES
Sequencing
Best practice design technique for operational amplifiers
includes careful attention to power sequencing. Although the
LM6584 is a bipolar op amp, recommended op amp turn on
power sequencing of ground (or V−), followed by V+, followed by input signal should be observed. Turn off power
sequence should be the reverse of the turn-on sequence.
Depending on how the amp is biased the outputs may swing
to the rails on power-on or power-off. Due to the high output
currents and rail to rail output stage in the LM6584 the output
may oscillate very slightly if the power is slowly raised between 2V and 4V The part is unconditionally stable at 5V.
Quick turn-off and turn-on times will eliminate oscillation
problems.
PSRR and Noise
Care should be taken to minimize the noise in the power
supply rails. The figure of merit for an op amp’s ability to
keep power supply noise out of the signal is called Power
Supply Rejection Ratio (PSRR). Observe from the PSRR
charts in the Typical Performance Characteristics section
that the PSRR falls of dramatically as the frequency of the
noise on the power supply line goes up. This is one of the
reasons switching power supplies can cause problems. It
should also be noticed from the charts that the negative
supply pin is far more susceptible to power noise. The design engineer should determine the switching frequencies
and ripple voltages of the power supplies in the system. If
required, a series resistor or in the case of a high current op
amp like the LM6584, a series inductor can be used to filter
out the noise.
Transients
In addition to the ripple and noise on the power supplies
there are also transient voltage changes. This can be
caused by another device on the same power supply suddenly drawing current or suddenly stopping a current draw.
The design engineer should insure that there are no damaging transients induced on the power supply lines when the op
amp suddenly changes current delivery.
OUTPUT SECTION
Current Rating
The LM6584 has an output current rating, sinking or sourcing, of 300mA. The LM6584 is ideally suited to loads that
require a high value of peak current but only a reduced value
of average current. This condition is typical of driving the
gate of a MOSFET. While the output drive rating is 300mA
peak, and the output structure supports rail-to-rail operation,
the attainable output current is reduced when the gain and
drive conditions are such that the output voltage approaches
either rail.
LAYOUT
Ground Planes
Do not assume the ground (or more properly, the common or
return) of the power supply is an ocean of zero impedance.
The thinner the trace, the higher the resistance. Thin traces
cause tiny inductances in the power lines. These can react
against the large currents the LM6584 is capable of delivering to cause oscillations, instability, overshoot and distortion.
A ground plane is the most effective way of insuring the
9
www.national.com
LM6584
Application Notes
LM6584
Application Notes
driven to the rail and the part can no longer maintain the
feedback loop, the internal circuitry will deliver large base
currents into the huge output transistors, trying to get the
outputs to get past the saturation voltage. The base currents
will approach 16 milliamperes and this will appear as an
increase in power supply current. Operating at this power
dissipation level for extended periods will damage the part,
especially in the higher thermal resistance TSSOP package.
Because of this phenomenon, unused parts should not have
the inputs strapped to either rail, but should have the inputs
biased at the midpoint or at least a diode drop (0.6V) within
the rails.
(Continued)
ground is a uniform low impedance. If a four layer board
cannot be used, consider pouring a plane on one side of a
two layer board. If this cannot be done be sure to use as
wide a trace as practicable and use extra decoupling capacitors to minimize the AC variations on the ground rail.
Decoupling
A high-speed, high-current amp like the LM6584 must have
generous decoupling capacitors. They should be as close to
the power pins as possible. Putting them on the back side
opposite the power pins may give the tightest layout. If
ground and power planes are available, the placement of the
decoupling caps are not as critical.
Self Heating
As discussed above the LM6584 is capable of significant
power by virtue of its 300mA current handling capability. A
TSSOP package cannot sustain these power levels for more
then a brief period.
Breadboards
The high currents and high frequencies the LM6584 operates at, as well as thermal considerations, require that prototyping of the design be done on a circuit board as opposed
to a “Proto-Board” style breadboard.
TFT Display Application
INTRODUCTION
In today’s high-resolution TFT displays, op amps are used
for the following three functions:
1. VCOM Driver
2. Gamma Buffer
3. Panel Repair Buffer
All of these functions utilize op amps as non-inverting, unitygain buffers. The VCOM Driver and Gamma Buffer are buffers
that supply a well regulated DC voltage. A Panel Repair
Buffer, on the other hand, provides a high frequency signal
that contains part of the display’s visual image.
STABILITY
General
High speed parts with large output current capability require
special care to insure lack of oscillations. Keep the “+” pin
isolated from the output to insure stability. As noted above
care should be take to insure the large output currents do not
appear in the ground or ground plane and then get coupled
into the “+” pin. As always, good tight layout is essential as is
adequate use of decoupling capacitors on the power supplies.
In an effort to reduce production costs, display manufacturers use a minimum variety of different parts in their TFT
displays. As a result, the same type of op amp will be used
for the VCOM Driver, Gamma Buffer, and Panel Repair Buffer.
To perform all these functions, such an op amp must have
the following characteristics:
1. Large output current drive
2. Rail to rail input common mode range
3. Rail to rail output swing
4. Medium speed gain bandwidth and slew rate
The LM6584 meets these requirements. It has a rail-to-rail
input and output, typical gain bandwidth and slew rate of
15MHz and 15V/µs, and it can supply up to 320mA of output
current. The following sections will describe the operation of
VCOM Drivers, Gamma Buffers, and Panel Repair Buffers,
showing how the LM6584 is well suited for each of these
functions.
Unity Gain
The unity gain or voltage-follower configuration is the most
subject to oscillation. If a part is stable at unity gain it is
almost certain to work in other configurations. In certain
applications where the part is setting a reference voltage or
is being used as a buffer greater stability can be achieved by
configuring the part as a gain of −1 or −2 or +2.
Phase Margin
The phase margin of an op amps gain-phase plot is an
indication of the stability of the amp. It is desirable to have at
least 45˚C of phase margin to insure stability in all cases.
The LM6584 has 60˚C of phase margin even with it’s large
output currents and Rail-to-Rail output stage, which are
generally more prone to stability issues.
Capacitive Load
The LM6584 can withstand 30pF of capacitive load in a unity
gain configuration before stability issues arise. At very large
capacitances, the load capacitor will attenuate the gain like
any other heavy load and the part becomes stable again.
The LM6584 will be stable at 330nF and higher load capacitance. Refer to the chart in the Typical Performance Characteristics section.
BRIEF OVERVIEW OF TFT DISPLAY
To better understand these op amp applications, let’s first
review a few basic concepts of how a TFT display operates.
Figure 1 is a simplified illustration of an LCD pixel. The top
and bottom plates of each pixel consist of Indium-Tin oxide
(ITO), which is a transparent, electrically conductive material. ITO lies on the inner surfaces of two glass substrates
that are the front and back glass panels of a TFT display.
Sandwiched between the two ITO plates is an insulating
material (liquid crystal) that alters the polarization of light to a
lesser a greater amount, depending on how much voltage
(VPIXEL) is applied across the two plates. Polarizers are
placed on the outer surfaces of the two glass substrates,
which in combination with the liquid crystal create a variable
OUTPUT
Swing vs. Current
The LM6584 will get to about 25mV or 30mV of either rail
when there is no load. The LM6584 can sink or source
hundreds of milliamperes while remaining less then 0.5V
away from the rail. It should be noted that if the outputs are
www.national.com
10
the Column Drivers supply this voltage via the column lines.
Column Drivers ‘write’ this voltage to the pixels one row at a
time, and this is accomplished by having the Row Drivers
select an individual row of pixels when their voltage levels
are transmitted by the Column Drivers. The Row Drivers
sequentially apply a large positive pulse (typically 25V to
35V) to each row line. This turns-on NMOS transistors connected to an individual row, allowing voltages from the column lines to be transmitted to the pixels.
(Continued)
light filter that modulates light transmitted from the back to
the front of a display. A pixel’s bottom plate lies on the
backside of a display where a light source is applied, and the
top plate lies on the front, facing the viewer. On a Twisted
Neumatic (TN) display, which is typical of most TFT displays,
a pixel transmits the greatest amount of light when VPIXEL is
less ± 0.5V, and it becomes less transparent as this voltage
increases with either a positive or negative polarity. In short,
an LCD pixel can be thought of as a capacitor, through
which, a controlled amount of light is transmitted by varying
VPIXEL.
VCOM DRIVER
The VCOM driver supplies a common voltage (VCOM) to all
the pixels in a TFT panel. VCOM is a constant DC voltage that
lies in the middle of the column drivers’ output voltage range.
As a result, when the column drivers write to a row of pixels,
they apply voltages that are either positive or negative with
respect to VCOM. In fact, the polarity of a pixel is reversed
each time its row is selected. This allows the column drivers
to apply an alternating voltage to the pixels rather than a DC
signal, which can ‘burn’ a pattern into an LCD display.
When column drivers write to the pixels, current pulses are
injected onto the VCOM line. These pulses result from charging stray capacitance between VCOM and the column lines
(see Figure 2), which ranges typically from 16pF to 33pF per
column. Pixel capacitance contributes very little to these
pulses because only one pixel at a time is connected to a
column, and the capacitance of a single pixel is on the order
of only 0.5pF. Each column line has a significant amount of
series resistance (typically 2kΩ to 40kΩ), so the stray capacitance is distributed along the entire length of a column.
This can be modeled by the multi-segment RC network
shown in Figure 3. The total capacitance between VCOM and
the column lines can range from 25nF to 100nF, and charging this capacitance can result in positive or negative current
pulses of 100mA, or more. In addition, a similar distributed
capacitance of approximately the same value exists between VCOM and the row lines. Therefore, the VCOM driver’s
load is the sum of these distributed RC networks with a total
capacitance of 50nF to 200nF, and this load can modeled
like the circuit in Figure 3.
20059226
FIGURE 1. Individual LCD Pixel
20059228
FIGURE 3. Model of Impedance between VCOM and
Column Lines
20059227
FIGURE 2. TFT Display
A VCOM driver is essentially a voltage regulator that can
source and sink current into a large capacitive load. To
simplify the analysis of this driver, the distributed RC network
of Figure 3 has been reduced to a single RC load in Figure
4. This load places a large capacitance on the VCOM driver
output, resulting in an additional pole in the op amp’s feedback loop. However, the op amp remains stable because
CLOAD and RESR create a zero that cancels the effect of this
pole. The range of CLOAD is 50nF to 200nF and RESR is 20Ω
to 100Ω, so this zero will have a frequency in the range of
Figure 2 is a simplified block diagram of a TFT display,
showing how individual pixels are connected to the row,
column, and VCOM lines. Each pixel is represented by capacitor with an NMOS transistor connected to its top plate.
Pixels in a TFT panel are arranged in rows and columns.
Row lines are connected to the NMOS gates, and column
lines to the NMOS sources. The back plate of every pixel is
connected to a common voltage called VCOM. Pixel brightness is controlled by voltage applied to the top plates, and
11
www.national.com
LM6584
TFT Display Application
LM6584
TFT Display Application
to C4 models the distributed RC load of a VCOM line. This RC
network is a gross simplification of what the actual impedance is on a TFT panel. However, it does provide a useful
test for measuring the op amp’s transient response when
driving a large capacitive load. A low impedance MOSFET
driver applies a 5V square wave to VSW, generating large
current pulses in the RC network. Scope photos from this
circuit are shown in Figure 6 and Figure 7. Figure 6 shows
the test circuit generates positive and negative voltage
spikes with an amplitude of ± 3.2V at the VCOM node, and
both transients settle-out in approximately 2µs. As mentioned before, the speed at which these transients settle-out
is a function of the op amp’s peak output current. The IOUT
trace in Figure 7 shows that the LM6584 can sink and source
peak currents of −310mA and 320mA. This ability to supply
large values of output current makes the LM6584 extremely
well suited for VCOM Driver applications.
(Continued)
8KHz to160KHz, which is much lower than the gain bandwidth of most op amps. As a result, the VCOM load adds very
little phase lag when op amp loop gain is unity, and this
allows the VCOM Driver to remain stable. This was verified by
measuring the small-signal bandwidth of the LM6584 with
the RC load of Figure 4. When driving an RC load of 50nF
and 20Ω, the LM6584 has a unity gain frequency of 6.12MHz
with 41.5˚C of phase margin. If the load capacitor is increased to 200nF and the resistance remains 20Ω, the unity
gain frequency is virtually unchanged: 6.05MHz with 42.9˚C
of phase margin.
20059229
FIGURE 4. VCOM Driver with Simplified Load
A VCOM Driver’s large-signal response time is determined by
the op amp’s maximum output current, not by its slew rate.
This is easily shown by calculating how much output current
is required to slew a 50nF load capacitance at the LM6584
slew rate of 14V/µs:
IOUT = 14V/µs x 50nF
= 700mA
20059231
FIGURE 6. VSW and VCOM Waveforms from VCOM
700mA exceeds the maximum current specification for the
LM6584 and almost all other op amps, confirming that a
VCOM driver’s speed is limited by its peak output current. In
order to minimize VCOM transients, the op amp used as a
VCOM Driver must supply large values of output current.
20059232
FIGURE 7. VSW and IOUT Waveforms from VCOM Test
Circuit
GAMMA BUFFER
Illumination in a TFT display, also referred to as grayscale, is
set by a series of discrete voltage levels that are applied to
each LCD pixel. These voltage levels are generated by
resistive DAC networks that reside inside each of the column
driver ICs. For example, a column driver with 64 Grayscale
20059230
FIGURE 5. VCOM Driver Test Circuit
Figure 5 is a common test circuit used for measuring VCOM
driver response time. The RC network of RL1 to RL3 and C1
www.national.com
12
LM6584
TFT Display Application
(Continued)
levels has a two 6 bit resistive DACs. Typically, the two
DACs will have their 64 resistors grouped into four segments, as shown in Figure 8. Each of these segments is
connected to external voltage lines, VGMA1 to VGMA10,
which are the Gamma Levels. VGMA1 to VGMA5 set grayscale voltage levels that are positive with respect to VCOM
(high polarity gamma levels). VGMA6 to VGMA10 set grayscale voltages negative with respect to VCOM (low polarity
gamma levels).
20059234
FIGURE 9. Basic Gamma Buffer Configuration
Another important specification for Gamma Buffers is small
signal bandwidth and slew rate. When column drivers select
which voltage levels are written to a row of pixels, their
internal DACs inject current spikes into the Gamma Lines.
This generates voltage transients at the Gamma Buffer outputs, and they should settle-out in less than 1µs to insure a
steady output voltage from the column drivers. Typically,
these transients have a maximum amplitude of 2V, so a
gamma buffer must have sufficient bandwidth and slew rate
to recover from a 2V transient in 1µs or less.
20059233
FIGURE 8. Simplified Schematic of Column Driver IC
Figure 9 shows how column drivers in a TFT display are
connected to the gamma levels. VGMA1, VGMA5, VGMA6,
and VGMA10 are driven by the Gamma Buffers. These
buffers serve as low impedance voltage sources that generate the display’s gamma levels. The Gamma Buffers’ outputs
are set by a simple resistive ladder, as shown in Figure 9.
Note that VGMA2 to VGMA4 and VGMA7 to VGMA9 are
usually connected to the column drivers even though they
are not driven by external buffers. Doing so, forces the
gamma levels in all the column drivers to be identical, minimizing grayscale mismatch between column drivers. Referring again to Figure 9, the resistive load of a column driver
DAC (i.e. resistance between GMA1 to GMA5) is typically
10kΩ to 15kΩ. On a typical display such as XGA, there can
be up to 10 column drivers, so the total resistive load on a
Gamma Buffer output can be as low as 1kΩ. The voltage
between VGMA1 and VGMA5 can range from 3V to 6V,
depending on the type of TFT panel. Therefore, maximum
load current supplied by a Gamma Buffer is approximately
6V/1kΩ = 6mA, which is a relatively light load for most op
amps. In many displays, VGMA1 can be less than 500mV
below VDD, and VGMA10 can be less than 500mV above
ground. Under these conditions, an op amp used for the
Gamma Buffer must have rail-to-rail inputs and outputs, like
the LM6584.
20059235
FIGURE 10. Large Signal Transient Response of an
Operational Amplifier
Figure 10 illustrates how an op amp responds to a largesignal transient. When such a transient occurs at t = 0, the
output does not start changing until TPD, which is the op
amp’s propagation delay time (typically 20ns for the
LM6584). The output then changes at the op amp’s slew rate
from t = TPD to TSR. From t = TSR to TSET, the output settles
to its final value (VF) at a speed determined by the op amp’s
small-signal frequency response. Although propagation de13
www.national.com
LM6584
TFT Display Application
rails. Therefore, op amps used as panel repair buffers should
have rail-to-rail input and stages. Otherwise, they may clip
the column driver signal.
The signal from a panel repair buffer is stored by a pixel
when the pixel’s row is selected. In high-resolution displays,
each row is selected for as little as 11µs. To insure that a
pixel has adequate time to settle-out during this brief period,
a panel repair buffer should settle to within 1% of its final
value approximately 1µs after a row is selected. This is
hardest to achieve when transmitting a column line’s maximum voltage swing, which is the difference between the
upper and lower gamma levels (i.e. voltage between VGMA1
and VGMA10). For a LM6584, the most demanding application occurs in displays that operate from a 13V supply. In
these displays, voltage difference between the top and bottom gamma levels can be as large as 12V, so the LM6584
needs to transmit a ± 12V pulse and settle to within 60mV of
its final value in approximately 1µs (60mV is approximately
1% of the dynamic range of the high or low polarity gamma
levels). LM6584 settling times for 12V and –12V pulses were
measured in a test circuit similar to the one in Figure 11. V+
and V− were set to 12.5V and –0.5V, respectively, when
measuring settling time for a 0V to 12V pulse. Likewise, V+
and V− were set to 0.5V and –12.5V when measuring settling time for a 0V to –12V pulse. In both cases, the LM6584
output was connected to a series RC load of 51Ω and 200pF.
When tested this way, the LM6584 settled to within 60mV of
12V or –12V in approximately 1.1µs. These observed values
are very close to the desired 1µs specification, demonstrating that the LM6584 has the bandwidth and slew rate required for repair buffers in high-resolution TFT displays.
(Continued)
lay and slew limited response time (t = 0 to TSR) can be
calculated from data sheet specifications, the small signal
settling time (TSR to TSET) cannot. This is because an op
amp’s gain vs. frequency has multiple poles, and as a result,
small-signal settling time can not be calculated as a simple
function of the op amp’s gain bandwidth. Therefore, the only
accurate method for determining op amp settling time is to
measure it directly.
20059236
FIGURE 11. Gamma Buffer Settling Time Test Circuit
The test circuit in Figure 11 was used to measure LM6584
settling time for a 2V pulse and 1kΩ load, which represents
the maximum transient amplitude and output load for a
gamma buffer. With this test system, the LM6584 settled to
within ± 30mV of 2V pulse in approximately 170ns. Settling
time for a 0 to –2V pulse was slightly less, 150ns. These
values are much smaller than the desired response time of
1µs, so the LM6584 has sufficient bandwidth and slew rate
for regulating gamma line transients.
PANEL REPAIR BUFFER
It is not uncommon for a TFT panel to be manufactured with
an open in one or two of its column or row lines. In order to
repair these opens, TFT panels have uncommitted repair
lines that run along their periphery. When an open line is
identified during a panel’s final assembly, a repair line reroutes its signal past the open. Figure 12 illustrates how a
column is repaired. The column driver’s output is sent to the
other end of an open column via a repair line, and the repair
line is driven by a panel repair buffer. When a column or row
line is repaired, the capacitance on that line increases substantially. For instance, a column typically has 50pF to
100pF of line capacitance, but a repaired column can have
up to 200pF. Column drivers are not designed to drive this
extra capacitance, so a panel repair buffer provides additional output current to the repaired column line. Note that
there is typically a 20Ω to 100Ω resistor in series with the
buffer output. This resistor isolates the output from the
200pF of capacitance on a repaired column line, ensuring
that the buffer remains stable. A pole is created by this
resistor and capacitance, but its frequency will be in the
range of 8MHz to 40MHz, so it will have only a minor effect
on the buffer’s transient response time. Panel repair buffers
transmit a column driver signal, and as mentioned in the
gamma buffer section, this signal is set by the gamma levels.
It was also mentioned that many displays have upper and
lower gamma levels that are within 500mV of the supply
www.national.com
20059237
FIGURE 12. Panel Repair Buffer
SUMMARY
This application note provided a basic explanation of how
op-amps are used in TFT displays, and it also presented the
specifications required for these op amps. There are three
major op amp applications in a display: VCOM Driver,
Gamma Buffer, and Panel Repair Buffer, and the LM6584
can be used for all of them. As a VCOM Driver, the LM6584
can supply large values of output current to regulate VCOM
load transients. It has rail-to-rail input common-mode range
and output swing required for gamma buffers and panel
repair buffers. It also has the necessary gain bandwidth and
slew-rate for regulating gamma levels and driving column
repair lines. All these features make the LM6584 very well
suited for use in TFT displays.
14
LM6584
Physical Dimensions
inches (millimeters) unless otherwise noted
14-Pin SOIC
NS Package Number M14A
14-Pin TSSOP
NS Package Number MTC14
15
www.national.com
LM6584 TFT-LCD Quad, 13V RRIO High Output Current Operational Amplifier
Notes
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products
Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain
no ‘‘Banned Substances’’ as defined in CSP-9-111S2.
National Semiconductor
Americas Customer
Support Center
Email: [email protected]
Tel: 1-800-272-9959
www.national.com
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
Email: [email protected]
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Support Center
Email: [email protected]
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: [email protected]
Tel: 81-3-5639-7560
Similar pages