TI1 LMV824QPWRQ1 Low-voltage rail-to-rail output operational amplifier Datasheet

LMV821-Q1 is Obsolete
LMV821-Q1
LMV822-Q1
LMV824-Q1
www.ti.com
SLOS461F – MARCH 2005 – REVISED JULY 2010
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
Check for Samples: LMV821-Q1, LMV822-Q1, LMV824-Q1
FEATURES
The LMV82x devices are characterized for operation
from –40°C to 125°C.
1
•
•
•
•
•
Qualified for Automotive Applications
2.5-V, 2.7-V, and 5-V Performance
–40°C to 125°C Operation
No Crossover Distortion
Low Supply Current at VCC+ = 5 V
– LMV821: 0.3 mA Typ
– LMV822: 0.5 mA Typ
– LMV824: 1 mA Typ
Rail-to-Rail Output Swing
Gain Bandwidth of 5.5 MHz Typ at 5 V
Slew Rate of 1.9 V/µs Typ at 5 V
•
•
•
LMV821...DBV PACKAGE
(TOP VIEW)
IN+
GND/VCCIN-
The LMV821 single, LMV822 dual, and LMV824 quad
devices are low-voltage (2.5 V to 5.5 V), low-power
commodity
operational
amplifiers.
Electrical
characteristics are very similar to the LMV3xx
operational amplifiers (low supply current, rail-to-rail
outputs, input common-mode range that includes
ground). However, the LMV82x devices offer a higher
bandwidth (5.5 MHz typical) and faster slew rate
(1.9 V/µs typical).
1OUT
1IN1IN+
GND/VCC-
PACKAGE (2)
(2)
(3)
3
4
OUT
1
8
2
7
3
6
4
5
VCC+
2OUT
2IN 2IN +
1OUT
1IN1IN+
VCC+
2IN+
2IN2OUT
1
14
2
13
3
12
4
11
5
10
6
9
7
8
ORDERABLE PART NUMBER
4OUT
4IN–
4IN+
GND/VCC3IN+
3IN–
3OUT
TOP-SIDE MARKING (3)
Single
SOT-23 – DBV
Reel of 3000
LMV821QDBVRQ1
RB1_
Dual
MSOP/VSSOP – DGK
Reel of 2500
LMV822QDGKRQ1
R8B
SOIC – D
Reel of 2500
LMV824QDRQ1
LMV824Q
TSSOP – PW
Reel of 2000
LMV824QPWRQ1
MV824Q
Quad
(1)
VCC+
LMV824...D OR PW PACKAGE
(TOP VIEW)
The LMV82x devices are cost-effective solutions for
applications
requiring
low-voltage/low-power
operation and space-saving considerations. The
LMV821 saves space on printed circuit boards and
enables the design of small portable electronic
devices (cordless and cellular phones, laptops, PDAs,
PCMIA). It also allows the designer to place the
device closer to the signal source to reduce noise
pickup and increase signal integrity.
ORDERING INFORMATION (1)
–40°C to 125°C
5
2
LMV822...DGK PACKAGE
(TOP VIEW)
DESCRIPTION/ORDERING INFORMATION
TA
1
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
DBV: The actual top-side marking has one additional character that designates the wafer fab/assembly site.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2005–2010, Texas Instruments Incorporated
LMV821-Q1
LMV822-Q1
LMV824-Q1
LMV821-Q1 is Obsolete
SLOS461F – MARCH 2005 – REVISED JULY 2010
www.ti.com
SYMBOL (EACH AMPLIFIER)
−
IN −
OUT
+
IN +
SIMPLIFIED SCHEMATIC
VCC
VBIAS1
+
VCC
−
VBIAS2
VBIAS5
+
+
Output
−
−
VCC VCC
VBIAS3
+
IN−
VBIAS4−
+
IN+
−
2
Submit Documentation Feedback
Copyright © 2005–2010, Texas Instruments Incorporated
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
LMV821-Q1
LMV822-Q1
LMV824-Q1
LMV821-Q1 is Obsolete
www.ti.com
SLOS461F – MARCH 2005 – REVISED JULY 2010
ABSOLUTE MAXIMUM RATINGS (1)
over operating free-air temperature range (unless otherwise noted)
VCC
Supply voltage (2)
5.5 V
(3)
VID
Differential input voltage
VI
Input voltage range (either input)
±VCC
VCC– to VCC+
Duration of output short circuit (one amplifier) to ground (4)
qJA
Package thermal impedance (5)
(6)
TJ
Operating virtual-junction temperature
Tstg
Storage temperature range
(1)
(2)
(3)
(4)
(5)
(6)
At or below TA = 25°C, VCC ≤ 5.5 V
Unlimited
D package
97°C/W
DBV package
206°C/W
DGK package
172°C/W
PW package
113°C/W
150°C
–65°C to 150°C
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values (except differential voltages and VCC specified for the measurement of IOS) are with respect to the network GND.
Differential voltages are at IN+ with respect to IN−.
Short circuits from outputs to VCC can cause excessive heating and eventual destruction.
Maximum power dissipation is a function of TJ(max), qJA, and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD = (TJ(max) – TA)/qJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
The package thermal impedance is calculated in accordance with JESD 51-7.
RECOMMENDED OPERATING CONDITIONS
MIN
MAX
VCC
Supply voltage (single-supply operation)
2.5
5
UNIT
V
TA
Operating free-air temperature
–40
125
°C
TYP
MAX
UNIT
1
6
2.5-V ELECTRICAL CHARACTERISTICS
VCC+ = 2.5 V, VCC– = 0 V, VIC = 1 V, VO = 1.25 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
VIO
TEST CONDITIONS
TA
25°C
Input offset voltage
–40°C to 125°C
High level
VCC+ = 2.5 V, RL = 600 Ω to 1.25 V
Low level
VO
MIN
Output swing
High level
VCC+ = 2.5 V, RL = 2 kΩ to 1.25 V
Low level
Copyright © 2005–2010, Texas Instruments Incorporated
6
25°C
2.28
–40°C to 125°C
2.18
25°C
2.37
0.13
–40°C to 125°C
2.38
–40°C to 125°C
2.28
25°C
2.46
0.08
–40°C to 125°C
0.22
0.32
25°C
V
0.14
0.22
Submit Documentation Feedback
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
mV
3
LMV821-Q1
LMV822-Q1
LMV824-Q1
LMV821-Q1 is Obsolete
SLOS461F – MARCH 2005 – REVISED JULY 2010
www.ti.com
2.7-V ELECTRICAL CHARACTERISTICS
VCC+ = 2.7 V, VCC– = 0 V, VIC = 1 V, VO = 1.35 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
MIN
25°C
VIO
Input offset voltage
aVIO
Average temperature coefficient
of input offset voltage
IIB
Input bias current
IIO
Input offset current
1
25°C
30
–40°C to 125°C
25°C
0.5
–40°C to 125°C
VIC = 0 to 1.7 V
25°C
70
68
25°C
75
–40°C to 125°C
70
–kSVR
Negative supply-voltage
rejection ratio
VCC+ = 1.7 V, VCC− = –1 V to –3.3 V,
VO = 0, VIC = 0
25°C
73
–40°C to 125°C
70
VICR
Common-mode input
voltage range
CMRR ≥ 50 dB
RL = 600 Ω to 1.35 V,
VO = 1.35 V to 2.2 V
Sourcing
RL = 600 Ω to 1.35 V,
VO = 1.35 V to 0.5 V
Sinking
RL = 2 kΩ to 1.35 V,
VO = 1.35 V to 2.2 V
Sourcing
Large-signal voltage amplification
RL = 2 kΩ to 1.35 V,
VO = 1.35 V to 0.5 V
Sinking
High level
VCC+ = 2.7 V,
RL = 600 Ω to 1.35 V
Low level
Output swing
High level
VCC+ = 2.7 V,
RL = 2 kΩ to 1.35 V
Low level
Output current
Supply current
90
100
–40°C to 125°C
85
25°C
85
–40°C to 125°C
80
25°C
95
–40°C to 125°C
90
25°C
90
–40°C to 125°C
85
25°C
2.5
–40°C to 125°C
2.4
25°C
–40°C to 125°C
2.5
25°C
2.58
0.2
2.66
0.08
–40°C to 125°C
V
0.12
0.2
12
16
VO = 2.7 V
Sinking
25°C
12
26
mA
0.22
0.3
0.45
0.6
–40°C to 125°C
0.5
–40°C to 125°C
25°C
dB
0.3
2.6
–40°C to 125°C
V
95
–40°C to 125°C
25°C
dB
100
0.13
25°C
nA
90
25°C
LMV822 (both amplifiers)
Submit Documentation Feedback
25°C
Sourcing
LMV824 (all four amplifiers)
4
–0.3
to 2
nA
dB
85
–0.2
to 1.9
mV
dB
85
25°C
25°C
30
85
VO = 0 V
LMV821
90
50
–40°C to 125°C
UNIT
µV/°C
140
VCC+ = 1.7 V to 4 V, VCC− = –1 V,
VO = 0, VIC = 0
ICC
6
25°C
Positive supply-voltage
rejection ratio
IO
1
6
+kSVR
VO
MAX
–40°C to 125°C
CMRR Common-mode rejection ratio
AV
TYP
0.8
0.72
mA
1
1.2
Copyright © 2005–2010, Texas Instruments Incorporated
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
LMV821-Q1
LMV822-Q1
LMV824-Q1
LMV821-Q1 is Obsolete
www.ti.com
SLOS461F – MARCH 2005 – REVISED JULY 2010
2.7-V ELECTRICAL CHARACTERISTICS (continued)
VCC+ = 2.7 V, VCC– = 0 V, VIC = 1 V, VO = 1.35 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
(1)
MIN
TYP
MAX
UNIT
SR
Slew rate
25°C
1.7
V/µs
GBW
Gain bandwidth product
(2)
25°C
5
MHz
Φm
Phase margin
(2)
25°C
60
deg
Gain margin
(2)
25°C
8.6
dB
(3)
Amplifier-to-amplifier isolation
VCC+ = 5 V, RL = 100 kΩ to 2.5 V
25°C
135
dB
Vn
Equivalent input noise voltage
f = 1 kHz, VIC = 1 V
25°C
45
nV/√Hz
In
Equivalent input noise current
f = 1 kHz
25°C
0.18
pA/√Hz
THD
Total harmonic distortion
f = 1 kHz, AV = –2, RL = 10 kΩ,
VO = 4.1 Vp-p
25°C
0.01
%
(1)
(2)
(3)
Connected as voltage follower with 1-V step input. Value specified is the slower of the positive and negative slew rates.
40-dB closed-loop dc gain, CL = 22 pF
Each amplifier excited in turn with 1 kHz to produce VO = 3 Vp-p
Copyright © 2005–2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
5
LMV821-Q1
LMV822-Q1
LMV824-Q1
LMV821-Q1 is Obsolete
SLOS461F – MARCH 2005 – REVISED JULY 2010
www.ti.com
5-V ELECTRICAL CHARACTERISTICS
VCC+ = 5 V, VCC– = 0 V, VIC = 2 V, VO = 2.5 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
MIN
25°C
VIO
Input offset voltage
aVIO
Average temperature coefficient
of input offset voltage
IIB
Input bias current
IIO
Input offset current
1
25°C
40
–40°C to 125°C
25°C
0.5
–40°C to 125°C
VIC = 0 to 4 V
25°C
72
70
25°C
75
–40°C to 125°C
70
–kSVR
Negative supply-voltage
rejection ratio
VCC+ = 1.7 V, VCC− = –1 V to –3.3 V,
VO = 0, VIC = 0
25°C
73
–40°C to 125°C
70
VICR
Common-mode input
voltage range
CMRR ≥ 50 dB
RL = 600 Ω to 2.5 V,
VO = 2.5 V to 4.5 V
Sourcing
RL = 600 Ω to 2.5 V,
VO = 2.5 V to 0.5 V
Sinking
RL = 2 kΩ to 2.5 V,
VO = 2.5 V to 4.5 V
Sourcing
Large-signal voltage amplification
RL = 2 kΩ to 2.5 V,
VO = 2.5 V to 0.5 V
Sinking
High level
VCC+ = 5 V,
RL = 600 Ω to 2.5 V
Low level
Output swing
High level
VCC+ = 5 V,
RL = 2 kΩ to 2.5 V
Low level
VO = 0 V
Sourcing
VO = 5 V
Sinking
Output current
LMV821
Supply current
LMV822 (both amplifiers)
LMV824 (all four amplifiers)
6
Submit Documentation Feedback
25°C
95
105
–40°C to 125°C
90
25°C
95
–40°C to 125°C
90
25°C
95
–40°C to 125°C
90
25°C
95
–40°C to 125°C
90
25°C
4.75
–40°C to 125°C
4.6
25°C
4.8
25°C
dB
105
4.84
0.25
4.9
0.1
–40°C to 125°C
V
0.15
0.2
25°C
20
–40°C to 125°C
15
25°C
20
–40°C to 125°C
15
45
mA
40
0.3
–40°C to 125°C
0.4
0.6
0.5
–40°C to 125°C
–40°C to 125°C
V
0.3
–40°C to 125°C
25°C
dB
105
–40°C to 125°C
4.85
nA
105
0.17
25°C
nA
dB
85
–0.3
to 4.3
mV
dB
85
–0.2
to 4.2
25°C
30
90
25°C
25°C
100
50
–40°C to 125°C
UNIT
µV/°C
150
VCC+ = 1.7 V to 4 V, VCC− = –1 V,
VO = 0, VIC = 0
ICC
6
25°C
Positive supply-voltage
rejection ratio
IO
1
6
+kSVR
VO
MAX
–40°C to 125°C
CMRR Common-mode rejection ratio
AV
TYP
0.7
0.9
1
mA
1.3
1.5
Copyright © 2005–2010, Texas Instruments Incorporated
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
LMV821-Q1
LMV822-Q1
LMV824-Q1
LMV821-Q1 is Obsolete
www.ti.com
SLOS461F – MARCH 2005 – REVISED JULY 2010
5-V ELECTRICAL CHARACTERISTICS (continued)
VCC+ = 5 V, VCC– = 0 V, VIC = 2 V, VO = 2.5 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC+ = 5 V
(1)
TA
MIN
TYP
25°C
1.4
MAX
UNIT
SR
Slew rate
1.9
V/µs
GBW
Gain bandwidth product
(2)
25°C
5.5
MHz
Φm
Phase margin
(2)
25°C
64.2
deg
Gain margin
(2)
25°C
8.7
dB
(3)
Amplifier-to-amplifier isolation
VCC+ = 5 V, RL = 100 kΩ to 2.5 V
25°C
135
dB
Vn
Equivalent input noise voltage
f = 1 kHz, VIC = 1 V
25°C
42
nV/√Hz
In
Equivalent input noise current
f = 1 kHz
25°C
0.2
pA/√Hz
THD
Total harmonic distortion
f = 1 kHz, AV = –2, RL = 10 kΩ,
VO = 4.1 Vp-p
25°C
0.01
%
(1)
(2)
(3)
Connected as voltage follower with 3-V step input. Value specified is the slower of the positive and negative slew rates.
40-dB closed-loop dc gain, CL = 22 pF
Each amplifier excited in turn with 1 kHz to produce VO = 3 Vp-p
Copyright © 2005–2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
7
LMV821-Q1
LMV822-Q1
LMV824-Q1
LMV821-Q1 is Obsolete
SLOS461F – MARCH 2005 – REVISED JULY 2010
www.ti.com
TYPICAL CHARACTERISTICS
TA = 25°C, VCC+ = 5-V single supply (unless otherwise noted)
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
1200
INPUT CURRENT
vs
TEMPERATURE
−30
All Channels
VCC+ = 5 V
Vin = VCC+/2
TA = 855C
−40
II − Input Current − nA
ICC − Supply Current − µA
1000
TA = 255C
800
600
TA = −405C
400
−50
−60
200
−70
−40
0
0
1
2
3
4
VCC+ − Supply Voltage − V
5
6
0
20
40
60
TA − Temperature − °C
80
100
0.01
0.1
1
Output Voltage Referenced to V+ − (V)
10
Figure 1.
Figure 2.
SOURCING CURRENT
vs
OUTPUT VOLTAGE
SOURCING CURRENT
vs
OUTPUT VOLTAGE
100
100
VCC+ = 2.7 V
VCC+ = 5 V
10
IO − Source Current − mA
IO − Source Current − mA
−20
1
0.1
0.01
0.001
0.01
0.1
1
Output Voltage Referenced to V+ − (V)
10
10
1
0.1
0.01
0.001
Figure 3.
8
Submit Documentation Feedback
Figure 4.
Copyright © 2005–2010, Texas Instruments Incorporated
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
LMV821-Q1
LMV822-Q1
LMV824-Q1
LMV821-Q1 is Obsolete
www.ti.com
SLOS461F – MARCH 2005 – REVISED JULY 2010
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VCC+ = 5-V single supply (unless otherwise noted)
SINKING CURRENT
vs
OUTPUT VOLTAGE
SINKING CURRENT
vs
OUTPUT VOLTAGE
100
100
VCC+ = 2.7 V
VCC+ = 5 V
10
IO − Sink Current − mA
IO − Sink Current − mA
10
1
1
0.1
0.1
0.01
0.01
0.1
0.01
1
10
Output Voltage Referenced to GND − V
Figure 5.
Figure 6.
OUTPUT VOLTAGE SWING
vs
SUPPLY VOLTAGE
OUTPUT VOLTAGE SWING
vs
SUPPLY VOLTAGE
RL = 2 kΩ to Mid Rail
Output Voltage From Supply Voltage − mV
Output Voltage From Supply Voltage − mV
10
80
RL = 10 kΩ to Mid Rail
40
30
Negative Swing
20
0
2.6
1
Output Voltage Referenced to GND − V
50
10
0.1
0.01
Positive Swing
3
3.4
3.8
4.2
VCC+ − Supply Voltage − V
4.6
5
70
60
50
Negative Swing
40
Positive Swing
30
20
10
0
2.6
3
3.4
3.8
4.2
VCC+ − Supply Voltage − V
Figure 7.
Copyright © 2005–2010, Texas Instruments Incorporated
4.6
5
Figure 8.
Submit Documentation Feedback
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
9
LMV821-Q1
LMV822-Q1
LMV824-Q1
LMV821-Q1 is Obsolete
SLOS461F – MARCH 2005 – REVISED JULY 2010
www.ti.com
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VCC+ = 5-V single supply (unless otherwise noted)
OUTPUT VOLTAGE SWING
vs
SUPPLY VOLTAGE
160
RL = 600 Ω to Mid Rail
Output Voltage From Supply Voltage − mV
Output Voltage From Supply Voltage − mV
160
OUTPUT VOLTAGE SWING
vs
LOAD RESISTANCE
150
140
Negative Swing
130
120
110
Positive Swing
100
90
80
70
60
2.6
RlL = 5 kΩ to Mid Rail
VCC+ = 5 V
140
120
100
80
60
40
20
0
3
3.4
3.8
4.2
4.6
100
5
VCC+ − Supply Voltage − V
1000
10k
Resistive Load − Ω
Figure 9.
Figure 10.
CROSSTALK REJECTION
vs
FREQUENCY
+PSRR
vs
FREQUENCY
100
160
100k
VCC+ = +2.5 V
90
150
140
70
VCC+ = +1.35 V
PSRR − dB
Crosstalk Rejection − dB
80
130
120
110
100
90
100
60
50
40
30
VCC+ = ±2.5 V
VI = 3 VPP
RL = 5 kΩ
AV = 1
20
10
1k
10k
Frequency − Hz
100k
0
100
1k
Figure 11.
10
Submit Documentation Feedback
10k
Frequency − Hz
100k
1M
Figure 12.
Copyright © 2005–2010, Texas Instruments Incorporated
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
LMV821-Q1
LMV822-Q1
LMV824-Q1
LMV821-Q1 is Obsolete
www.ti.com
SLOS461F – MARCH 2005 – REVISED JULY 2010
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VCC+ = 5-V single supply (unless otherwise noted)
–PSRR
vs
FREQUENCY
100
VCC+ = +2.5 V
90
80
PSRR − dB
70
60 VCC+ = +1.35 V
50
40
30
20
10
0
100
1k
10k
100k
Frequency − Hz
Figure 13.
1M
GAIN AND PHASE MARGIN
vs
FREQUENCY
(VCC+ = 2.7 V, RL = 600 Ω, 2 kΩ, 100 kΩ)
80
140
Gain − dB
Phase
60
100
50
80
40
60
30
40
Gain
20
20
0
10
VCC+ = 2.7 V
600 Ω
2 kΩ
100 kΩ
0
−10
−20
−40
−20
1k
Phase Margin − Deg
120
70
10k
100k
−60
10M
1M
Frequency − Hz
Figure 14.
Copyright © 2005–2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
11
LMV821-Q1
LMV822-Q1
LMV824-Q1
LMV821-Q1 is Obsolete
SLOS461F – MARCH 2005 – REVISED JULY 2010
www.ti.com
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VCC+ = 5-V single supply (unless otherwise noted)
GAIN AND PHASE MARGIN
vs
FREQUENCY
(VCC+ = 5 V, RL = 600 Ω, 2 kΩ, 100 kΩ)
80
140
70
120
100
Phase
50
80
40
60
30
40
20
20
Gain
0
10
−10
−20
−20
VCC+ = 5 V
600 Ω
2 kΩ
100 kΩ
0
1k
Phase Margin − Deg
Gain − dB
60
−40
10k
100k
Frequency − Hz
1M
−60
10M
Figure 15.
GAIN AND PHASE MARGIN
vs
FREQUENCY
(VCC+ = 2.7 V, RL = 10 kΩ, CL = 22 pF, 100 pF, 200 pF)
80
100
70
Gain − dB
60
60
50
40
40
20
30
0
20
−20
Gain
−40
10
VCC+ = 2.7 V
RL = 10 kΩ
22 pF
100 pF
200 pF
0
−10
−60
−80
−20
1k
Phase Margin − Deg
80
Phase
10k
100k
1M
−100
10M
Frequency − Hz
Figure 16.
12
Submit Documentation Feedback
Copyright © 2005–2010, Texas Instruments Incorporated
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
LMV821-Q1
LMV822-Q1
LMV824-Q1
LMV821-Q1 is Obsolete
www.ti.com
SLOS461F – MARCH 2005 – REVISED JULY 2010
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VCC+ = 5-V single supply (unless otherwise noted)
GAIN AND PHASE MARGIN
vs
FREQUENCY
(VCC+ = 5 V, RL = 10 kΩ, CL = 22 pF, 100 pF, 200 pF)
80
100
70
80
Phase
60
50
40
40
20
0
30
Gain
−20
20
10
0
−10
−20
−40
VCC+ = 5 V
RL = 10 kΩ
22 pF
100 pF
200 pF
1k
Phase Margin − Deg
Gain − dB
60
−60
−80
10k
100k
−100
10M
1M
Frequency − Hz
Figure 17.
GAIN AND PHASE MARGIN
vs
FREQUENCY
(VCC+ = 2.7 V, RL = 600 Ω, CL = 22 pF, 100 pF, 200 pF)
80
140
70
120
100
Phase
50
80
40
60
30
40
20
20
Gain
VCC+ = 2.7 V
RL = 600 Ω
10
0
−20
22 pF
100 pF
200 pF
−10
−20
0
1k
Phase Margin − Deg
Gain − dB
60
−40
10k
100k
−60
10M
1M
Frequency − Hz
Figure 18.
Copyright © 2005–2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
13
LMV821-Q1
LMV822-Q1
LMV824-Q1
LMV821-Q1 is Obsolete
SLOS461F – MARCH 2005 – REVISED JULY 2010
www.ti.com
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VCC+ = 5-V single supply (unless otherwise noted)
GAIN AND PHASE MARGIN
vs
FREQUENCY
(VCC+ = 5 V, RL = 600 Ω, CL = 22 pF, 100 pF, 200 pF)
80
140
70
120
Phase
100
50
80
40
60
40
30
Gain
20
20
10
VCC+ = 5 V
RL = 600 Ω
0
−20
22 pF
100 pF
200 pF
−10
−20
0
1k
Phase Margin − Deg
Gain − dB
60
−40
10k
100k
1M
−60
10M
Frequency − Hz
Figure 19.
14
Submit Documentation Feedback
Copyright © 2005–2010, Texas Instruments Incorporated
Product Folder Link(s): LMV821-Q1 LMV822-Q1 LMV824-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
17-Aug-2012
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
TBD
Lead/
Ball Finish
Call TI
MSL Peak Temp
(3)
Samples
(Requires Login)
LMV821QDBVRQ1
ACTIVE
SOT-23
DBV
5
Call TI
LMV822QDGKRQ1
ACTIVE
VSSOP
DGK
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
LMV824QDRQ1
ACTIVE
SOIC
D
14
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
LMV824QPWRQ1
ACTIVE
TSSOP
PW
14
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LMV821-Q1, LMV822-Q1, LMV824-Q1 :
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
17-Aug-2012
• Catalog: LMV821, LMV822, LMV824
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
LMV824QPWRQ1
Package Package Pins
Type Drawing
TSSOP
PW
14
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2000
330.0
12.4
Pack Materials-Page 1
6.9
B0
(mm)
K0
(mm)
P1
(mm)
5.6
1.6
8.0
W
Pin1
(mm) Quadrant
12.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LMV824QPWRQ1
TSSOP
PW
14
2000
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
Similar pages