NSC LP3962EMPX-2.5 1.5a fast ultra low dropout linear regulator Datasheet

LP3962/LP3965
1.5A Fast Ultra Low Dropout Linear Regulators
General Description
Features
The LP3962/LP3965 series of fast ultra low-dropout linear
regulators operate from a +2.5V to +7.0V input supply. Wide
range of preset output voltage options are available. These
ultra low dropout linear regulators respond very fast to step
changes in load which makes them suitable for low voltage
microprocessor applications. The LP3962/LP3965 are developed on a CMOS process which allows low quiescent
current operation independent of output load current. This
CMOS process also allows the LP3962/LP3965 to operate
under extremely low dropout conditions.
Dropout Voltage: Ultra low dropout voltage; typically 38mV
at 150mA load current and 380mV at 1.5A load current.
Ground Pin Current: Typically 5mA at 1.5A load current.
Shutdown Mode: Typically 15µA quiescent current when
the shutdown pin is pulled low.
Error Flag: Error flag goes low when the output voltage
drops 10% below nominal value (for LP3962).
SENSE: Sense pin improves regulation at remote loads.
(For LP3965)
Precision Output Voltage: Multiple output voltage options
are available ranging from 1.2V to 5.0V and adjustable
(LP3965), with a guaranteed accuracy of ± 1.5% at room
temperature, and ± 3.0% over all conditions (varying line,
load, and temperature).
n
n
n
n
n
n
n
n
n
n
n
n
Ultra low dropout voltage
Low ground pin current
Load regulation of 0.04%
15µA quiescent current in shutdown mode
Guaranteed output current of 1.5A DC
Available in SOT-223,TO-263 and TO-220 packages
Output voltage accuracy ± 1.5%
Error flag indicates output status (LP3962)
Sense option improves better load regulation (LP3965)
Extremely low output capacitor requirements
Overtemperature/overcurrent protection
−40˚C to +125˚C junction temperature range
Applications
n
n
n
n
n
n
n
n
Microprocessor power supplies
GTL, GTL+, BTL, and SSTL bus terminators
Power supplies for DSPs
SCSI terminator
Post regulators
High efficiency linear regulators
Battery chargers
Other battery powered applications
Typical Application Circuits
10126601
*SD and ERROR pins must be pulled high through a 10kΩ pull-up resistor. Connect the ERROR pin to ground if this function is not used. See applications
section for more information.
** See Application Hints.
© 2001 National Semiconductor Corporation
DS101266
www.national.com
LP3962/LP3965 1.5A Fast Ultra Low Dropout Linear Regulators
November 2001
LP3962/LP3965
Typical Application Circuits
(Continued)
10126634
*SD and ERROR pins must be pulled high through a 10kΩ pull-up resistor. Connect the ERROR pin to ground if this function is not used. See applications section
for more information.
** See Application Hints.
Block Diagram LP3962
10126603
www.national.com
2
LP3962/LP3965
Block Diagram LP3965
10126629
Block Diagram LP3965-ADJ
10126635
3
www.national.com
LP3962/LP3965
Connection Diagrams
10126605
Top View
TO220-5 Package
Bent, Staggered Leads
10126604
10126606
Top View
TO263-5 Package
Top View
SOT 223-5 Package
Pin Description for SOT223-5 Package
Pin #
1
LP3962
Name
LP3965
Function
SD
Shutdown
2
VIN
Input Supply
3
VOUT
4
ERROR
5
GND
Output Voltage
ERROR Flag
Name
Function
SD
Shutdown
VIN
Input Supply
VOUT
Output Voltage
SENSE/ADJ
Ground
Remote Sense Pin or
Output Adjust Pin
GND
Ground
Pin Description for TO220-5 and TO263-5 Packages
Pin #
1
LP3962
Name
LP3965
Function
Name
Function
SD
Shutdown
2
VIN
Input Supply
3
GND
Ground
GND
Ground
4
VOUT
Output Voltage
VOUT
Output Voltage
5
ERROR
ERROR Flag
SD
Shutdown
VIN
Input Supply
SENSE/ADJ
Remote Sense Pin or
Output Adjust Pin
Ordering Information
10126631
Package Type Designator is ’MP’ for SOT223 package, ’T’ for TO220 package, and ’S’ for TO263 package.
www.national.com
4
(Continued)
TABLE 1. Package Marking and Ordering Information
Output
Voltage
Order Number
Description
(Current, Option)
Package
Type
Package Marking
Supplied As:
5.0
LP3962EMP-5.0
1.5A, Error Flag
SOT223-5
LBTB
1000 units on Tape and
Reel
5.0
LP3962EMPX-5.0
1.5A, Error Flag
SOT223-5
LBTB
2000 units on Tape and
Reel
3.3
LP3962EMP-3.3
1.5A, Error Flag
SOT223-5
LBEB
1000 units on Tape and
Reel
3.3
LP3962EMPX-3.3
1.5A, Error Flag
SOT223-5
LBEB
2000 units on Tape and
Reel
2.5
LP3962EMP-2.5
1.5A, Error Flag
SOT223-5
LBDB
1000 units on Tape and
Reel
2.5
LP3962EMPX-2.5
1.5A, Error Flag
SOT223-5
LBDB
2000 units on Tape and
Reel
1.8
LP3962EMP-1.8
1.5A, Error Flag
SOT223-5
LBCB
1000 units on Tape and
Reel
1.8
LP3962EMPX-1.8
1.5A, Error Flag
SOT223-5
LBCB
2000 units on Tape and
Reel
5.0
LP3965EMP-5.0
1.5A, SENSE
SOT223-5
LBVB
1000 units on Tape and
Reel
5.0
LP3965EMPX-5.0
1.5A, SENSE
SOT223-5
LBVB
2000 units on Tape and
Reel
3.3
LP3965EMP-3.3
1.5A, SENSE
SOT223-5
LBNB
1000 units on Tape and
Reel
3.3
LP3965EMPX-3.3
1.5A, SENSE
SOT223-5
LBNB
2000 units on Tape and
Reel
2.5
LP3965EMP-2.5
1.5A, SENSE
SOT223-5
LBLB
1000 units on Tape and
Reel
2.5
LP3965EMPX-2.5
1.5A, SENSE
SOT223-5
LBLB
2000 units on Tape and
Reel
1.8
LP3965EMP-1.8
1.5A, SENSE
SOT223-5
LBKB
1000 units on Tape and
Reel
1.8
LP3965EMPX-1.8
1.5A, SENSE
SOT223-5
LBKB
2000 units on Tape and
Reel
ADJ
LP3965EMP-ADJ
1.5A, ADJ
SOT223-5
LBRB
1000 units on Tape and
Reel
ADJ
LP3965EMPX-ADJ
1.5A, ADJ
SOT223-5
LBRB
2000 units on Tape and
Reel
5.0
LP3962ES-5.0
1.5A, Error Flag
TO263-5
LP3962ES-5.0
Rail
5.0
LP3962ESX-5.0
1.5A, Error Flag
TO263-5
LP3962ESX-5.0
Tape and Reel
3.3
LP3962ES-3.3
1.5A, Error Flag
TO263-5
LP3962ES-3.3
Rail
3.3
LP3962ESX-3.3
1.5A, Error Flag
TO263-5
LP3962ES-3.3
Tape and Reel
2.5
LP3962ES-2.5
1.5A, Error Flag
TO263-5
LP3962ES-2.5
Rail
2.5
LP3962ESX-2.5
1.5A, Error Flag
TO263-5
LP3962ES-2.5
Tape and Reel
1.8
LP3962ES-1.8
1.5A, Error Flag
TO263-5
LP3962ES-1.8
Rail
1.8
LP3962ESX-1.8
1.5A, Error Flag
TO263-5
LP3962ES-1.8
Tape and Reel
5.0
LP3965ES-5.0
1.5A, SENSE
TO263-5
LP3965ES-5.0
Rail
5.0
LP3965ESX-5.0
1.5A, SENSE
TO263-5
LP3965ES-5.0
Tape and Reel
3.3
LP3965ES-3.3
1.5A, SENSE
TO263-5
LP3965ES-3.3
Rail
3.3
LP3965ESX-3.3
1.5A, SENSE
TO263-5
LP3965ES-3.3
Tape and Reel
2.5
LP3965ES-2.5
1.5A, SENSE
TO263-5
LP3965ES-2.5
Rail
5
www.national.com
LP3962/LP3965
Ordering Information
LP3962/LP3965
Ordering Information
(Continued)
TABLE 1. Package Marking and Ordering Information (Continued)
Output
Voltage
Order Number
Description
(Current, Option)
Package
Type
Package Marking
Supplied As:
2.5
LP3965ESX-2.5
1.5A, SENSE
TO263-5
LP3965ES-2.5
Tape and Reel
1.8
LP3965ES-1.8
1.5A, SENSE
TO263-5
LP3965ES-1.8
Rail
1.8
LP3965ESX-1.8
1.5A, SENSE
TO263-5
LP3965ES-1.8
Tape and Reel
ADJ
LP3965ES-ADJ
1.5A, ADJ
TO263-5
LP3965ES-ADJ
Rail
ADJ
LP3965ESX-ADJ
1.5A, ADJ
TO263-5
LP3965ES-ADJ
Tape and Reel
5.0
LP3962ET-5.0
1.5A, Error Flag
TO220-5
LP3962ET-5.0
Rail
3.3
LP3962ET-3.3
1.5A, Error Flag
TO220-5
LP3962ET-3.3
Rail
2.5
LP3962ET-2.5
1.5A, Error Flag
TO220-5
LP3962ET-2.5
Rail
1.8
LP3962ET-1.8
1.5A, Error Flag
TO220-5
LP3962ET-1.8
Rail
5.0
LP3965ET-5.0
1.5A, SENSE
TO220-5
LP3965ET-5.0
Rail
3.3
LP3965ET-3.3
1.5A, SENSE
TO220-5
LP3965ET-3.3
Rail
2.5
LP3965ET-2.5
1.5A, SENSE
TO220-5
LP3965ET-2.5
Rail
1.8
LP3965ET-1.8
1.5A, SENSE
TO220-5
LP3965ET-1.8
Rail
ADJ
LP3965ET-ADJ
1.5A, ADJ
TO220-5
LP3965ET-ADJ
Rail
www.national.com
6
(Note 1)
IOUT (Survival)
Maximum Voltage for ERROR
Pin
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Storage Temperature Range
Short Circuit Protected
VIN+0.3V
Maximum Voltage for SENSE Pin
VOUT+0.3V
−65˚C to +150˚C
Lead Temperature
Operating Ratings
(Soldering, 5 sec.)
260˚C
ESD Rating (Note 3)
2 kV
Power Dissipation (Note 2)
Internally Limited
Input Supply Voltage (Survival)
Shutdown Input Voltage
(Survival)
Input Supply Voltage (Operating),
(Note 12)
Shutdown Input Voltage
(Operating)
−0.3V to +7.5V
−0.3V to VIN+0.3V
Output Voltage (Survival), (Note
6), (Note 7)
2.5V to 7.0V
−0.3V to VIN+0.3V
Maximum Operating Current (DC)
1.5A
Operating Junction Temp. Range
−40˚C to +125˚C
−0.3V to +7.5V
Electrical Characteristics
LP3962/LP3965
Limits in standard typeface are for TJ = 25˚C, and limits in boldface type apply over the full operating temperature range.
Unless otherwise specified: VIN = VO(NOM) + 1V, IL = 10 mA, COUT = 33µF, VSD = VIN-0.3V.
Symbol
Parameter
Conditions
Typ
(Note 4)
LP3962/5 (Note 5)
Units
Min
Max
0
-1.5
-3.0
+1.5
+3.0
%
1.216
1.198
1.180
1.234
1.253
V
Output Voltage
Tolerance
(Note 8)
10 mA ≤ IL ≤ 1.5A
VOUT +1 ≤ VIN≤ 7.0V
VADJ
Adjust Pin Voltage (ADJ
version)
10 mA ≤ IL ≤ 1.5A
VOUT +1.5V ≤ VIN≤ 7.0V
∆V OL
Output Voltage Line
Regulation (Note 8)
VOUT+1V < VIN < 7.0V,
0.02
0.06
%
∆VO/ ∆IOUT
Output Voltage Load
Regulation
(Note 8)
10 mA < IL < 1.5 A
0.04
0.09
%
VO
VIN - VOUT
Dropout Voltage
(Note 10)
IGND
Ground Pin Current In
Normal Operation Mode
IL = 150 mA
38
45
55
IL = 1.5 A
380
450
550
IL = 150 mA
4
9
10
IL = 1.5 A
5
14
15
25
75
IGND
Ground Pin Current In
Shutdown Mode
(Note 11)
VSD ≤ 0.2V
15
IO(PK)
Peak Output Current
(Note 2)
2.5
2.0
1.7
mV
mA
µA
A
SHORT CIRCUIT PROTECTION
ISC
Short Circuit Current
4.5
A
OVER TEMPERATURE PROTECTION
Tsh(t)
Shutdown Threshold
165
˚C
Tsh(h)
Thermal Shutdown
Hysteresis
10
˚C
SHUTDOWN INPUT
VSDT
Shutdown Threshold
Output = High
VIN
Output = Low
0
7
VIN–0.3
0.2
V
www.national.com
LP3962/LP3965
Absolute Maximum Ratings
LP3962/LP3965
Electrical Characteristics
LP3962/LP3965 (Continued)
Limits in standard typeface are for TJ = 25˚C, and limits in boldface type apply over the full operating temperature range.
Unless otherwise specified: VIN = VO(NOM) + 1V, IL = 10 mA, COUT = 33µF, VSD = VIN-0.3V.
Symbol
Parameter
Conditions
Typ
(Note 4)
LP3962/5 (Note 5)
Min
Units
Max
TdOFF
Turn-off delay
IL = 1.5 A
20
TdON
Turn-on delay
IL = 1.5 A
25
µs
SD Input Current
VSD = VIN
1
nA
ISD
µs
ERROR FLAG COMPARATOR
VT
Threshold
(Note 9)
10
5
16
%
VTH
Threshold Hysteresis
(Note 9)
5
2
8
%
VEF(Sat)
Error Flag Saturation
Isink = 100µA
0.02
0.1
V
Td
Flag Reset Delay
1
µs
Ilk
Error Flag Pin Leakage
Current
1
nA
VError = 0.5V (over temp.)
1
mA
VIN = VOUT + 1.5V
COUT = 100uF
VOUT = 3.3V
60
VIN = VOUT + 0.3V
COUT = 100uF
VOUT = 3.3V
40
Imax
Error Flag Pin Sink
Current
AC PARAMETERS
PSRR
Ripple Rejection
ρn(l/f
Output Noise Density
f = 120Hz
0.8
en
Output Noise Voltage
(rms)
BW = 10Hz – 100kHz
150
BW = 300Hz – 300kHz
100
dB
µV
µV (rms)
Note 1: Absolute maximum ratings indicate limits beyond which damage to the device may occur. Operating ratings indicate conditions for which the device is
intended to be functional, but does not guarantee specific performance limits. For guaranteed specifications and test conditions, see Electrical Charateristics. The
guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed
test conditions.
Note 2: At elevated temperatures, devices must be derated based on package thermal resistance. The devices in TO220 package must be derated at θjA = 50˚C/W
(with 0.5in2, 1oz. copper area), junction-to-ambient (with no heat sink). The devices in the TO263 surface-mount package must be derated at θjA = 60˚C/W (with
0.5in2, 1oz. copper area), junction-to-ambient. The devices in SOT223 package must be derated at θjA = 90˚C/W (with 0.5in2, 1oz. copper area), junction-to-ambient.
Note 3: The human body model is a 100pF capacitor discharged through a 1.5kΩ resistor into each pin.
Note 4: Typical numbers are at 25˚C and represent the most likely parametric norm.
Note 5: Limits are 100% production tested at 25˚C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate National’s Average Outgoing Quality Level (AOQL).
Note 6: If used in a dual-supply system where the regulator load is returned to a negative supply, the LP396X output must be diode-clamped to ground.
Note 7: The output PMOS structure contains a diode between the VIN and VOUT terminals. This diode is normally reverse biased. This diode will get forward biased
if the voltage at the output terminal is forced to be higher than the voltage at the input terminal. This diode can typically withstand 200mA of DC current and 1Amp
of peak current.
Note 8: Output voltage line regulation is defined as the change in output voltage from the nominal value due to change in the input line voltage. Output voltage load
regulation is defined as the change in output voltage from the nominal value due to change in load current. The line and load regulation specification contains only
the typical number. However, the limits for line and load regulation are included in the output voltage tolerance specification.
Note 9: Error Flag threshold and hysteresis are specified as percentage of regulated output voltage.
Note 10: Dropout voltage is defined as the minimum input to output differential voltage at which the output drops 2% below the nominal value. Dropout voltage
specification applies only to output voltages of 2.5V and above. For output voltages below 2.5V, the drop-out voltage is nothing but the input to output differential,
since the minimum input voltage is 2.5V.
Note 11: This specification has been tested for −40˚C ≤ TJ ≤ 85˚C since the temperature rise of the device is negligible under shutdown conditions.
Note 12: The minimum operating value for VIN is equal to either [VOUT(NOM) + VDROPOUT] or 2.5V, whichever is greater.
www.national.com
8
Unless otherwise specified, VIN =VO(NOM) + 1V, VOUT= 2.5V,
COUT = 33µF, IOUT = 10mA, CIN = 68µF, VSD = VIN, and TA = 25˚C.
Drop-Out Voltage vs Temperature for Different Load
Currents
Drop-Out Voltage vs Temperature for Different Output
Voltages (IOUT = 800mA
10126609
10126610
Ground Pin Current vs Input Voltage (VSD=VIN)
Ground Pin Current vs Input Voltage (VSD=100mV)
10126611
10126615
Ground Current vs Temperature (VSD=VIN)
Ground Current vs Temperature (VSD=0V
10126618
10126612
9
www.national.com
LP3962/LP3965
Typical Performance Characteristics
LP3962/LP3965
Typical Performance Characteristics
Unless otherwise specified, VIN =VO(NOM) + 1V, VOUT= 2.5V,
COUT = 33µF, IOUT = 10mA, CIN = 68µF, VSD = VIN, and TA = 25˚C. (Continued)
Ground Pin Current vs Shutdown Pin Voltage
Input Voltage vs Output Voltage
10126617
10126616
Output Noise Density, VOUT= 2.5V
Output Noise Density, VOUT= 5V
10126613
10126614
Load Transient Response
Ripple Rejection vs Frequency
10126637
10126638
www.national.com
10
Unless otherwise specified, VIN =VO(NOM) + 1V, VOUT= 2.5V,
COUT = 33µF, IOUT = 10mA, CIN = 68µF, VSD = VIN, and TA = 25˚C. (Continued)
δVOUT vs Temperature
Noise Density VIN = 3.5V, VOUT = 2.5V, IL = 10 mA
10126639
10126640
Line Transient Response
Line Transient Response
10126641
10126642
Line Transient Response (IOUT = 1.5A)
Line Transient Response (IOUT = 1.5A)
10126643
10126644
11
www.national.com
LP3962/LP3965
Typical Performance Characteristics
LP3962/LP3965
Applications Information
very little capacitance variation with temperature, but a ceramic may not be as good (depending on dielectric type).
Aluminum electrolytics also typically have large temperature
variation of capacitance value.
EXTERNAL CAPACITORS
Like any low-dropout regulator, external capacitors are required to assure stability. these capacitors must be correctly
selected for proper performance.
Equally important to consider is a capacitor’s ESR change
with temperature: this is not an issue with ceramics, as their
ESR is extremely low. However, it is very important in Tantalum and aluminum electrolytic capacitors. Both show increasing ESR at colder temperatures, but the increase in
aluminum electrolytic capacitors is so severe they may not
be feasible for some applications (see Capacitor Characteristics Section).
INPUT CAPACITOR: The LP3962/5 requires a low source
impedance to maintain regulator stability because the internal bias circuitry is connected directly to VIN. The input
capacitor must be located less than 1 cm from the LP3962/5
device and connected directly to the input and ground pins
using traces which have no other currents flowing through
them (see PCB Layout section).
The minimum allowable input capacitance for a given application depends on the type of the capacitor and ESR
(equivalent series resistance). A lower ESR capacitor allows
the use of less capacitance, while higher ESR types (like
aluminum electrolytics) require more capacitance.
The lowest value of input capacitance that can be used for
stable full-load operation is 68 µF (assuming it is a ceramic
or low-ESR Tantalum with ESR less than 100 mΩ).
To determine the minimum input capacitance amount and
ESR value, an approximation which should be used is:
CIN ESR (mΩ) / CIN (µF) ≤ 1.5
CAPACITOR CHARACTERISTICS
CERAMIC: For values of capacitance in the 10 to 100 µF
range, ceramics are usually larger and more costly than
tantalums but give superior AC performance for bypassing
high frequency noise because of very low ESR (typically less
than 10 mΩ). However, some dielectric types do not have
good capacitance characteristics as a function of voltage
and temperature.
Z5U and Y5V dielectric ceramics have capacitance that
drops severely with applied voltage. A typical Z5U or Y5V
capacitor can lose 60% of its rated capacitance with half of
the rated voltage applied to it. The Z5U and Y5V also exhibit
a severe temperature effect, losing more than 50% of nominal capacitance at high and low limits of the temperature
range.
X7R and X5R dielectric ceramic capacitors are strongly recommended if ceramics are used, as they typically maintain a
capacitance range within ± 20% of nominal over full operating ratings of temperature and voltage. Of course, they are
typically larger and more costly than Z5U/Y5U types for a
given voltage and capacitance.
TANTALUM: Solid Tantalum capacitors are recommended
for use on the output because their typical ESR is very close
to the ideal value required for loop compensation. They also
work well as input capacitors if selected to meet the ESR
requirements previously listed.
Tantalums also have good temperature stability: a good
quality Tantalum will typically show a capacitance value that
varies less than 10-15% across the full temperature range of
125˚C to −40˚C. ESR will vary only about 2X going from the
high to low temperature limits.
The increasing ESR at lower temperatures can cause oscillations when marginal quality capacitors are used (if the ESR
of the capacitor is near the upper limit of the stability range at
room temperature).
ALUMINUM: This capacitor type offers the most capacitance for the money. The disadvantages are that they are
larger in physical size, not widely available in surface mount,
and have poor AC performance (especially at higher frequencies) due to higher ESR and ESL.
Compared by size, the ESR of an aluminum electrolytic is
higher than either Tantalum or ceramic, and it also varies
greatly with temperature. A typical aluminum electrolytic can
exhibit an ESR increase of as much as 50X when going from
25˚C down to −40˚C.
It should also be noted that many aluminum electrolytics only
specify impedance at a frequency of 120 Hz, which indicates
they have poor high frequency performance. Only aluminum
electrolytics that have an impedance specified at a higher
frequency (between 20 kHz and 100 kHz) should be used for
This shows that input capacitors with higher ESR values can
be used if sufficient total capacitance is provided. Capacitor
types (aluminum, ceramic, and tantalum) can be mixed in
parallel, but the total equivalent input capacitance/ESR must
be defined as above to assure stable operation.
IMPORTANT: The input capacitor must maintain its ESR and
capacitance in the ’stable range’ over the entire temperature
range of the application to assure stability (see Capacitor
Characteristics Section).
OUTPUT CAPACITOR: An output capacitor is also required
for loop stability. It must be located less than 1 cm from the
LP3962/5 device and connected directly to the output and
ground pins using traces which have no other currents flowing through them (see PCB Layout section).
The minimum value of the output capacitance that can be
used for stable full-load operation is 33 µF, but it may be
increased without limit. The output capacitor’s ESR is critical
because it forms a zero to provide phase lead which is
required for loop stability. The ESR must fall within the
specified range:
0.2Ω ≤ COUT ESR ≤ 5Ω
The lower limit of 200 mΩ means that ceramic capacitors are
not suitable for use as LP3962/5 output capacitors (but can
be used on the input). Some ceramic capacitance can be
used on the output if the total equivalent ESR is in the stable
range: when using a 100 µF Tantalum as the output capacitor, approximately 3 µF of ceramic capacitance can be applied before stability becomes marginal.
IMPORTANT: The output capacitor must meet the requirements for minimum amount of capacitance and also have an
appropriate ESR value over the full temperature range of the
application to assure stability (see Capacitor Characteristics
Section).
SELECTING A CAPACITOR
It is important to note that capacitance tolerance and variation with temperature must be taken into consideration when
selecting a capacitor so that the minimum required amount
of capacitance is provided over the full operating temperature range. In general, a good Tantalum capacitor will show
www.national.com
12
quencies, ground planes begin to look inductive and
RFI/EMI can cause ground bounce across the ground plane.
In multi-layer PCB applications, care should be taken in
layout so that noisy power and ground planes do not radiate
directly into adjacent layers which carry analog power and
ground.
(Continued)
the LP396X. Derating must be applied to the manufacturer’s
ESR specification, since it is typically only valid at room
temperature.
Any applications using aluminum electrolytics should be
thoroughly tested at the lowest ambient operating temperature where ESR is maximum.
Output Adjustment
An adjustable output device has output voltage range of
1.215V to 5.1V. To obtain a desired output voltage, the
following equation can be used with R1 always a 10kΩ
resistor.
PCB LAYOUT
Good PC layout practices must be used or instability can be
induced because of ground loops and voltage drops. The
input and output capacitors must be directly connected to the
input, output, and ground pins of the LP3962/5 using traces
which do not have other currents flowing in them Kelvin
connect).
The best way to do this is to lay out CIN and COUT near the
device with short traces to the VIN, VOUT, and ground pins.
The regulator ground pin should be connected to the external circuit ground so that the regulator and its capacitors
have a ’single point ground’.
It should be noted that stability problems have been seen in
applications where ’vias’ to an internal ground plane were
used at the ground points of the LP3962/5 IC and the input
and output capacitors. This was caused by varying ground
potentials at these nodes resulting from current flowing
through the ground plane. Using a single point ground technique for the regulator and it’s capacitors fixed the problem.
Since high current flows through the traces going into VIN
and coming from VOUT, Kelvin connect the capacitor leads to
these pins so there is no voltage drop in series with the input
and output capacitors.
For output stability, CF must be between 68pF and 100pF.
Output Noise
Noise is specified in two waysSpot Noise or Output noise density is the RMS sum of all
noise sources, measured at the regulator output, at a specific frequency (measured with a 1Hz bandwidth). This type
of noise is usually plotted on a curve as a function of frequency.
Total output Noise or Broad-band noise is the RMS sum
of spot noise over a specified bandwidth, usually several
decades of frequencies.
Attention should be paid to the units of measurement. Spot
noise is measured in units µV/√Hz or nV/√Hz and total output
noise is measured in µV(rms).
The primary source of noise in low-dropout regulators is the
internal reference. In CMOS regulators, noise has a low
frequency component and a high frequency component,
which depend strongly on the silicon area and quiescent
current. Noise can be reduced in two ways: by increasing the
transistor area or by increasing the current drawn by the
internal reference. Increasing the area will decrease the
chance of fitting the die into a smaller package. Increasing
the current drawn by the internal reference increases the
total supply current (ground pin current). Using an optimized
trade-off of ground pin current and die size, LP3962/LP3965
achieves low noise performance and low quiescent current
operation.
The total output noise specification for LP3962/LP3965 is
presented in the Electrical Characteristics table. The Output
noise density at different frequencies is represented by a
curve under typical performance characteristics.
RFI/EMI SUSCEPTIBILITY
RFI (radio frequency interference) and EMI (electromagnetic
interference) can degrade any integrated circuit’s performance because of the small dimensions of the geometries
inside the device. In applications where circuit sources are
present which generate signals with significant high frequency energy content ( > 1 MHz), care must be taken to
ensure that this does not affect the IC regulator.
If RFI/EMI noise is present on the input side of the LP396X
regulator (such as applications where the input source
comes from the output of a switching regulator), good ceramic bypass capacitors must be used at the input pin of the
LP396X.
If a load is connected to the LP396X output which switches
at high speed (such as a clock), the high-frequency current
pulses required by the load must be supplied by the capacitors on the LP396X output. Since the bandwidth of the
regulator loop is less than 100 kHz, the control circuitry
cannot respond to load changes above that frequency. The
means the effective output impedance of the LP396X at
frequencies above 100 kHz is determined only by the output
capacitor(s).
In applications where the load is switching at high speed, the
output of the LP396X may need RF isolation from the load. It
is recommended that some inductance be placed between
the LP396X output capacitor and the load, and good RF
bypass capacitors be placed directly across the load.
PCB layout is also critical in high noise environments, since
RFI/EMI is easily radiated directly into PC traces. Noisy
circuitry should be isolated from ’clean’ circuits where possible, and grounded through a separate path. At MHz fre-
Short-Circuit Protection
The LP3962and LP3965 is short circuit protected and in the
event of a peak over-current condition, the short-circuit control loop will rapidly drive the output PMOS pass element off.
Once the power pass element shuts down, the control loop
will rapidly cycle the output on and off until the average
power dissipation causes the thermal shutdown circuit to
respond to servo the on/off cycling to a lower frequency.
Please refer to the section on thermal information for power
dissipation calculations.
Error Flag Operation
The LP3962/LP3965 produces a logic low signal at the Error
Flag pin when the output drops out of regulation due to low
input voltage, current limiting, or thermal limiting. This flag
13
www.national.com
LP3962/LP3965
Applications Information
LP3962/LP3965
Applications Information
a pull up resistor. Although the ERROR pin can sink current
of 1mA, this current is energy drain from the input supply.
Hence, the value of the pull up resistor should be in the
range of 10kΩ to 1MΩ. The ERROR pin must be connected to ground if this function is not used. It should
also be noted that when the shutdown pin is pulled low, the
ERROR pin is forced to be invalid for reasons of saving
power in shutdown mode.
(Continued)
has a built in hysteresis. The timing diagram in Figure 1
shows the relationship between the ERROR and the output
voltage. In this example, the input voltage is changed to
demonstrate the functionality of the Error Flag.
The internal Error flag comparator has an open drain output
stage. Hence, the ERROR pin should be pulled high through
10126607
FIGURE 1. Error Flag Operation
Sense Pin
In applications where the regulator output is not very close to
the load, LP3965 can provide better remote load regulation
using the SENSE pin. Figure 2 depicts the advantage of the
SENSE option. LP3962 regulates the voltage at the output
pin. Hence, the voltage at the remote load will be the regulator output voltage minus the drop across the trace resis-
www.national.com
tance. For example, in the case of a 3.3V output, if the trace
resistance is 100mΩ, the voltage at the remote load will be
3.15V with 1.5 A of load current, ILOAD. The LP3965 regulates the voltage at the sense pin. Connecting the sense pin
to the remote load will provide regulation at the remote load,
as shown in Figure 2. If the sense option pin is not required,
the sense pin must be connected to the VOUT pin.
14
LP3962/LP3965
Applications Information
(Continued)
10126608
FIGURE 2. Improving remote load regulation using LP3965
Shutdown Operation
A CMOS Logic level signal at the shutdown ( SD) pin will
turn-off the regulator. Pin SD must be actively terminated
through a 10kΩ pull-up resistor for a proper operation. If this
pin is driven from a source that actively pulls high and low
(such as a CMOS rail to rail comparator), the pull-up resistor
is not required. This pin must be tied to Vin if not used.
The maximum allowable temperature rise (TRmax) depends
on the maximum ambient temperature (TAmax) of the application, and the maximum allowable junction temperature(TJmax):
TRmax = TJmax− TAmax
The maximum allowable value for junction to ambient Thermal Resistance, θJA, can be calculated using the formula:
θJA = TRmax / PD
Dropout Voltage
The dropout voltage of a regulator is defined as the minimum
input-to-output differential required to stay within 2% of the
output voltage. The LP3962/LP3965 use an internal MOSFET with an Rds(on) of 240mΩ (typically). For CMOS LDOs,
the dropout voltage is the product of the load current and the
Rds(on) of the internal MOSFET.
LP3962 and LP3965 are available in TO-220, TO-263, and
SOT-223 packages. The thermal resistance depends on
amount of copper area or heat sink, and on air flow. If the
maximum allowable value of θJA calculated above is ≥ 60
˚C/W for TO-220 package, ≥60 ˚C/W for TO-263 package,
and ≥ 140 ˚C/W for SOT-223 package, no heatsink is
needed since the package can dissipate enough heat to
satisfy these requirements. If the value for allowable θJA falls
below these limits, a heat sink is required.
Reverse Current Path
The internal MOSFET in LP3962and LP3965 has an inherent parasitic diode. During normal operation, the input voltage is higher than the output voltage and the parasitic diode
is reverse biased. However, if the output is pulled above the
input in an application, then current flows from the output to
the input as the parasitic diode gets forward biased. The
output can be pulled above the input as long as the current
in the parasitic diode is limited to 200mA continuous and 1A
peak.
Heatsinking TO-220 Packages
The thermal resistance of a TO220 package can be reduced
by attaching it to a heat sink or a copper plane on a PC
board. If a copper plane is to be used, the values of θJA will
be same as shown in next section for TO263 package.
The heatsink to be used in the application should have a
heatsink to ambient thermal resistance,
θHA≤ θJA − θCH − θJC.
Maximum Output Current Capability
LP3962 and LP3965 can deliver a continuous current of 1.5
A over the full operating temperature range. A heatsink may
be required depending on the maximum power dissipation
and maximum ambient temperature of the application. Under
all possible conditions, the junction temperature must be
within the range specified under operating conditions. The
total power dissipation of the device is given by:
PD = (VIN−VOUT)IOUT+ (VIN)IGND
In this equation, θCH is the thermal resistance from the
junction to the surface of the heat sink and θJC is the thermal
resistance from the junction to the surface of the case. θJC is
about 3˚C/W for a TO220 package. The value for θCH depends on method of attachment, insulator, etc. θCH varies
between 1.5˚C/W to 2.5˚C/W. If the exact value is unknown,
2˚C/W can be assumed.
where IGND is the operating ground current of the device
(specified under Electrical Characteristics).
15
www.national.com
LP3962/LP3965
Applications Information
(Continued)
Heatsinking TO-263 and SOT-223 Packages
The TO-263 and SOT223 packages use the copper plane on
the PCB as a heatsink. The tab of these packages are
soldered to the copper plane for heat sinking. Figure 3
shows a curve for the θJA of TO-263 package for different
copper area sizes, using a typical PCB with 1 ounce copper
and no solder mask over the copper area for heat sinking.
10126619
FIGURE 5. θJA vs Copper(1 Ounce) Area for SOT-223
package
The following figures show different layout scenarios for
SOT-223 package.
10126632
FIGURE 3. θJA vs Copper(1 Ounce) Area for TO-263
package
As shown in the figure, increasing the copper area beyond 1
square inch produces very little improvement. The minimum
value for θJA for the TO-263 packag mounted to a PCB is
32˚C/W.
10126620
FIGURE 6. SCENARIO A, θJA = 148˚C/W
Figure 4 shows the maximum allowable power dissipation
for TO-263 packages for different ambient temperatures,
assuming θJA is 35˚C/W and the maximum junction temperature is 125˚C.
10126621
FIGURE 7. SCENARIO B, θJA = 125˚C/W
10126633
FIGURE 4. Maximum power dissipation vs ambient
temperature for TO-263 package
Figure 5 shows a curve for the θJA of SOT-223 package for
different copper area sizes, using a typical PCB with 1 ounce
copper and no solder mask over the copper area for heat
sinking.
www.national.com
16
LP3962/LP3965
Applications Information
(Continued)
10126622
FIGURE 8. SCENARIO C, θJA = 92˚C/W
10126624
FIGURE 10. SCENARIO E, θJA = 77˚C/W
10126623
FIGURE 9. SCENARIO D, θJA = 83˚C/W
10126625
FIGURE 11. SCENARIO F, θJA = 75˚C/W
17
www.national.com
LP3962/LP3965
Applications Information
(Continued)
10126626
FIGURE 12. SCENARIO G, θJA = 113˚C/W
10126627
FIGURE 13. SCENARIO H, θJA = 79˚C/W
www.national.com
18
LP3962/LP3965
Applications Information
(Continued)
10126628
FIGURE 14. SCENARIO I, θJA = 78.5˚C/W
19
www.national.com
LP3962/LP3965
Physical Dimensions
inches (millimeters)
unless otherwise noted
TO220 5-lead, Molded, Stagger Bend Package (TO220-5)
NS Package Number T05D
For Order Numbers, refer to the “Ordering Information” section of this document.
www.national.com
20
LP3962/LP3965
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
TO263 5-Lead, Molded, Surface Mount Package (TO263-5)
NS Package Number TS5B
For Order Numbers, refer to the “Ordering Information” section of this document.
21
www.national.com
LP3962/LP3965 1.5A Fast Ultra Low Dropout Linear Regulators
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
SOT223, 5-Lead, Molded, Surface Mount Package (SOT223-5)
NS Package Number MA05C
For Order Numbers, refer to the “Ordering Information” section of this document.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
National Semiconductor
Corporation
Americas
Email: [email protected]
www.national.com
National Semiconductor
Europe
Fax: +49 (0) 180-530 85 86
Email: [email protected]
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: [email protected]
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
Similar pages