Murata LQH6KKN2R2N43K Chip inductor (chip coil) power inductor (wire wound type) lqh6pp sery Datasheet

Inductors (Coils) > Chip Inductor (Chip Coil) > Power Inductor (Wire Wound Type)
Data Sheet
Chip Inductor (Chip Coil)
1
Power Inductor (Wire Wound Type)
LQH6PP Series (2424 Size)
■ Dimensions
■ Packaging
Code
Packaging
Minimum Quantity
L
180mm Embossed Tape
250
K
330mm Embossed Tape
1500
(0.2)
4.3±0.2
6.0±0.2
1.65±0.2
1.65±0.2
0.85 (typ.)
2.3 (typ.)
6.0±0.2
6.0±0.2
(in mm)
■ Rated Value (p: packaging code)
Inductance
Rated Current
(Based on Inductance Change)
Rated Current
(Based on Temperature Rise)
DC Resistance
Self Resonance
Frequency (min.)
LQH6PPN1R0N43p
1.0µH±30%
7.50A
4.30A
0.009ohm±30%
110MHz
LQH6PPN1R5N43p
1.5µH±30%
6.50A
4.15A
0.010ohm±30%
60MHz
LQH6PPN2R2N43p
2.2µH±30%
5.60A
4.10A
0.014ohm±30%
30MHz
LQH6PPN3R3N43p
3.3µH±30%
4.50A
3.80A
0.016ohm±30%
30MHz
LQH6PPN4R7M43p
4.7µH±20%
4.00A
3.20A
0.020ohm±30%
25MHz
LQH6PPN6R8M43p
6.8µH±20%
3.20A
2.85A
0.028ohm±30%
20MHz
LQH6PPN100M43p
10µH±20%
2.60A
2.60A
0.044ohm±30%
15MHz
LQH6PPN150M43p
15µH±20%
2.20A
2.20A
0.065ohm±30%
10MHz
LQH6PPN220M43p
22µH±20%
1.70A
1.55A
0.108ohm±30%
10MHz
LQH6PPN330M43p
33µH±20%
1.60A
1.29A
0.137ohm±30%
6MHz
LQH6PPN470M43p
47µH±20%
1.25A
1.10A
0.230ohm±30%
6MHz
LQH6PPN680M43p
68µH±20%
1.10A
1.00A
0.289ohm±30%
5MHz
LQH6PPN101M43p
100µH±20%
0.92A
0.80A
0.436ohm±30%
3MHz
Part Number
Test Frequency: 100kHz
Class of Magnetic Shield: Magnetic shield of magnetic powder in resin
Operating Temperature Range (Self-temperature rise is included): -40°C to +125°C
Operating Temperature Range (Self-temperature rise is not included): -40°C to +85°C
Only for reflow soldering.
Continued on the following page.
o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design.
! Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2010.9.9
http://www.murata.com/
Inductors (Coils) > Chip Inductor (Chip Coil) > Power Inductor (Wire Wound Type)
Data Sheet
2
Continued from the preceding page.
■ Notice (Rated Current)
<Rated Current>
(Based on Inductance Change)
When Rated Current is applied to the Products,
Inductance will be within +-30% of nominal
Inductance value.
<Rated Current>
(Based on Temperature Rise)
When Rated Current is applied to the Products,
self-generation of heat will rise to 40°C or less.
■ Inductance-Frequency Characteristics (Typ.)
100µH
Inductance (µH)
100
10
1000
100µH
68µH
47µH
33µH
22µH
15µH
10µH
6.8µH
4.7µH
3.3µH
2.2µH
33µH
22µH
68µH
47µH
15µH
10µH
100
6.8µH
Inductance (µH)
1000
■ Inductance-Current Characteristics (Typ.)
1.5µH
4.7µH
10
1.0µH
1
1
3.3µH
0.1
0.1
1
10
Frequency (MHz)
100
0.1
10
1000
1.5µH
2.2µH
100
1.0µH
1000
10000
Current (mA)
■ Temperature Rise Characteristics (Typ.)
40
100µH
15µH
68µH
22µH
47µH
4.7µH
10µH
6.8µH
Temperature Rise (°C)
30
33µH
20
3.3µH
2.2µH
1.5µH
1.0µH
10
0
0
1000
2000
3000
Current (mA)
4000
5000
■ !Caution/Notice
!Caution (Rating)
Do not use products beyond the rated current as
this may create excessive heat.
Notice
Solderability of Tin plating termination chip might be
deteriorated when low temperature soldering profile
where peak solder temperature is below the Tin melting
point is used. Please confirm the solderability of Tin
plating termination chip before use.
o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design.
! Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2010.9.9
http://www.murata.com/
Similar pages