IRC TT LRC-LR1206LF-01-R020-G Low value current sense flat chip resistor Datasheet

Low Value Current Sense
Flat Chip Resistor
LR Series
• Resistance range from 0.002Ω up to 1Ω
• Standard Sn/Pb and Pb lead-free terminations available
• High power dissipation at 70°C
• Tolerances to ±1%
Electrical Data
Resistance
Range1
Size
Tolerance
F, G, J, K
Tolerance
J, K
TCR2
(ppm/°C)
Tolerance
K
1206
0.003 to 1W
2010
0.010 to 1W 0.003 to 1W 0.002 to 1W
2512
0.002 to 1W
1
2
Power
Rating
at 70°C
(Watts)
Dielectric
Withstanding
Voltage (V)
0.5
±100
Maximum
Current
(Amps)
Operating
Temperature
Pad and Trace Area
for Max Power
Rating @ 70°C
16
200
1.0
30mm2
-55°C to +150°C
22
2.0
32
100mm2
300mm2
Non-standard resistance values available
Contact factory for TCR information on values under 0.05ohms
Outline Dimensions
D
L
W
Solder Plating
Ni Barrier Layer
H
Protective Overcoat
Cu Wraparound
Termination
Cu Termination
E
Alumina Substrate
1206
2010
2512
in.
mm
in.
mm
in.
mm.
L
0.126 ± 0.012
3.20 ± 0.305
0.206 ± 0.015
5.23 ± 0.38
0.256 ± 0.015
6.50 ± 0.38
W
0.064 ± 0.008
1.63 ± 0.203
0.104 ± 0.010
2.64 ± 0.25
0.128 ± .010
3.25 ± 0.25
H
0.024 ± 0.004
0.61 ± 0.102
0.029 ± 0.004
0.74 ± 0.1
0.029 ± 0.004
0.74 ± 0.1
D
0.019 ± 0.010
0.48 ± 0.25
0.019 ± 0.010
0.48 ± 0.25
0.019 ± 0.010
0.48 ± 0.25
E
0.019 ± 0.010
0.48 ± 0.25
0.019 ± 0.010
0.48 ± 0.25
0.019 ± 0.010
0.48 ± 0.25
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
Advanced Film Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Email: [email protected] • Website: www.irctt.com
A subsidiary of
TT electronics plc
LR Series Issue May 2009
Low Value Current Sense
Flat Chip Resistor
Environmental Performance
Environmental Test
Test Method
Typical Performance
MIL-STD-202 Method 107G
Condition B, -55°C +150°C, 100 cycles
±0.5% + 1.0mW
6.25X Rated Power for 5 seconds
±0.5% + 0.5mW
100 hours @150°C
±0.5% + 0.5mW
MIL-STD-202, Method 301
2.5X Rated Voltage, 1 minute
±0.25% + 0.5mW
MIL-STD-202 Method 106
±0.5% + 0.5mW
1000 hours, Rated Power, 70°C
1.5 hours on, 30 minutes off
±1.0% + 0.5mW
1 hour -65°C followed by rated power for 45 min
±0.5% + 0.5mW
Resistance to Solder Heat
MIL-STD-202 Method 210
260°C, 10 seconds
±0.5% + 1.0mW
Insulation Resistance
MIL-STD-202 Method 302
100VDC, 1 minute
>1000 megohms
Solderability
MIL-STD-202 Method 208
245°C, 5 seconds
95% min Coverage
Thermal Shock
Short Time Overload
High Temperature Exposure
Dielectric Withstanding Voltage
Moisture Resistance
Load Life
Low Temperature Operation
Power Derating and Pulse/Surge Capability
Power Derating Curve
Pulse and Surge Capability
Surge Power Watts
% Of Rated Power
100
50
10
25°
70°
150°
Temperature in °C
70
50
30
20
10
7
5
3
300 µSec
1 mSec
Ordering Procedure
Prefix
Average power
dissipationnot to
exceed normal
70°C rating
LRC 25
12 2 wa
tts
LRC 20
10 1 wa
tt
LRC 12
06 0.5
watts
3 mSec
10 mSec
30 mSec
100 mSec
300 mSec
1 Sec
Surge or Repetitive Pulse Duration
Recommended Solder Pad Layout
A
LRC - LRF 1206LF - 01 - R020 - F
Model
LR for values > 0.025Ω
LRF for values ≤ 0.025Ω
B
Size
C
1206; 1206LF; 2010; 2010LF; 2512; 2512LF
(LF=Lead Free Terminations)
DIM.
TCR Code
01 = ±100ppm/°C
Resistance Code
A
4-Digit resistance code. Ex: R050 = 0.050Ω; 1R00 = 1Ω
Tolerance Code
B
F = ±1%, G = ±2%, J = ±5%
C
For additional information or to discuss your specific requirements,
please contact our Applications Team using the contact details below.
Advanced Film Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Email: [email protected] • Website: www.irctt.com
LR1206
LR2010
LR2512
in.
0.080
0.120
0.145
mm
(2.0)
(3.05)
(3.7)
in.
0.160
0.255
0.305
mm
(4.0)
(6.5)
(7.75)
in.
0.050
0.060
0.060
mm
(1.25)
(1.5)
(1.5)
LR Series Issue May 2009
Similar pages