Rohm LSH6008-CA50A Add-on structure contact image sensor head Datasheet

Add-on Structure Contact Image Sensor Heads
LSH6008-CA50A
The Basic CIS by which the add-on can shorten the development period of a product sharply while being
able to satisfy broad demand.A taper glass and tempered glass can respond as an option.
As a measure against a paper jam, the custom-made correspondence of the special cantact plate can be
carried out.
Applications
Document Scanners,Bill sorters.Wide Format Scanners,and Lottery.
Features
1) High speed reading capability due to 3 analog output.
2) Signal amplifier integrated into each sensor IC in order to eliminate external noise ; compatible with 3.3V interface.
3) LED light source mounted on the same substrate as the sensor chip itself, resulting in a more compact, lightweight package.
4) Proprietary prism maintains a uniform output signal.
Dimensions (Unit : mm)
236±0.5
B
A
216
10±0.5
1
57th(29th) pixel
15.5±0.2
4±0.5
15.5±0.2
1
A-A
B
44±0.3
(55)
(55)
14.2±0.5
(55)
3.8±1
Fixing Pin
1
19.6
177±0.3
(55)
11.5±0.3
5±0.1
5±0.1
Focus point
Max.14
3±0.3
8.5
B-B
Max.0.2
Max.0.2
A
Max.0.2
Max.0.2
Max.0.2
B-B
A-A
(7)
No.16
No.1
FFC Insert Direction
5
(7.958)
(NOTE 1)
Deflection at the top of glass : 0 to 0.25mm
Projection to platen is positive.
(NOTE 2)
Connector : 04 6232 116 103 800 (Kyocera elco)
(NOTE 3)
General torelance : ±0.2
www.rohm.com
c 2012 ROHM Co., Ltd. All rights reserved.
○
1/4
Pin No.
No.1
No.2
No.3
No.4
No.5
No.6
No.7
No.8
Signal
Ao1
GND
Ao2
GND
Ao3
GND
MODE
VDD
Pin No.
No.9
No.10
No.11
No.12
No.13
No.14
No.15
No.16
Signal
VREF
SP
CLK
VLED
B-GND
G-GND
R-GND
NC
2012.10 - Rev.A
LSH6008-CA50A
Data Sheet
Characteristics
Parameter
Symbol
Typ.
Unit
Effective scanning width
−
216
mm
Primary scan dot density
−
600
dpi
−
5184
dots
Power supply voltage
VDD
3.3
V
Reference voltage
VREF
0.8
V
Scanning speed
SLT
0.28 x 3
ms / line
Total dot number
CLK
8
MHz
Maximum dynamic range
VRMax
0.5
V
Minimum dynamic range
VRMin.
0.25
V
Vod
VREF±0.1
V
−
5 to 45
°C
Clock frequency
Dark output
Operating temperature
Pin assignments
No.
Circuit
I/O
1
AO1
O
Analog output
Function
2
GND
I
Ground
3
AO2
O
Analog output
4
GND
I
Ground
5
AO3
O
Analog output
6
GND
I
Ground
7
MODE
I
Mode
8
VDD
I
Power supply
9
VREF
I
Reference voltage
10
SP
I
Start pulse
11
CLK
I
Clock
12
V-LED
I
LED power supply
13
B-GND
I
B-LED ground
14
G-GND
I
G-LED ground
15
R-GND
I
R-LED ground
16
NC
−
−
www.rohm.com
c 2012 ROHM Co., Ltd. All rights reserved.
○
2/4
2012.10 - Rev.A
LSH6008-CA50A
Data Sheet
Timing chart
(a) CLK Timing Chart
1/fCLK
twCLK
twCLK
CLK
ts
50%
50%
SP
tSETUP tHOLD
90%
A O1 to 3
1pixel
2pixel
(b) Data Output Timing Chart
After turning on the SP pulse, the analog output starts from the setting up point of 83 clock pulse.
1
2
82
83
CLK
SP
A O1 to 3
VREF output period
Vdummy
Analog output period
Vdummy
(300dpi)
A O1 :
A O2 :
A O3 :
1 to 82clock
_
_
1 to 28pixels
_
_
29 to 864pixels
865 to 1728pixels
1729 to 2572pixels
_
_
(600dpi)
A O1 :
A O2 :
A O3 :
1 to 82clock
_
_
1 to 56pixels
_
_
57 to 1728pixels
1729 to 3456pixels
3457 to 5144pixels
www.rohm.com
c 2012 ROHM Co., Ltd. All rights reserved.
○
3/4
2573 to 2592pixels
_
_
5145 to 5184pixels
2012.10 - Rev.A
LSH6008-CA50A
Data Sheet
Circuit diagram
VDD
0.1μF×6
1
2592
(5184)
GND
VDD
SP
VREF
ANALOG MEMORY CIRCUIT
CLK
MoDE
1
864
865
(1728) (1729)
1728 1729
(3456) (3457)
2592
(5184)
AO1
AO2
AO3
MODE
VREF
1μF×2
VLED
RGND
GGND
BGND
Peripheral circuit
CIS UNIT
16
15
14
13
12
1
3
5
9
8
10
11
2,4,6
7
GND
MODE
C5
R3
R4
R2
R
G
R1
B
R5
C1
C3
C2
LED GND
NC
C4
VLED
AO1
AO2
AO3
VREF
VDD
SP
CLK
∗ R1=R2=10 to 100Ω, R3 to R5=100KΩ,
C1=C2=47μF
C3=100μF, C4=0.1μF, C5=100pF
Note : The above constant values are examples, and please adjust the parameters
by evaluating waveforms with the device which is used
www.rohm.com
c 2012 ROHM Co., Ltd. All rights reserved.
○
4/4
2012.10 - Rev.A
Notice
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specifications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specified in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, fire or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any
of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
R1120A
Similar pages