LINER LT1991HMS-PBF Precision, 100î¼a gain selectable amplifi er Datasheet

LT1991
Precision, 100µA
Gain Selectable Amplifier
FEATURES
DESCRIPTION
n
The LT®1991 combines a precision operational amplifier
with eight precision resistors to form a one-chip solution
for accurately amplifying voltages. Gains from –13 to 14
with a gain accuracy of 0.04% can be achieved using no
external components. The device is particularly well suited
for use as a difference amplifier, where the excellent resistor matching results in a common mode rejection ratio of
greater than 75dB.
n
n
n
n
n
n
n
n
n
n
n
Pin Configurable as a Difference Amplifier,
Inverting and Noninverting Amplifier
Difference Amplifier
Gain Range 1 to 13
CMRR >75dB
Noninverting Amplifier
Gain Range 0.07 to 14
Inverting Amplifier
Gain Range –0.08 to –13
Gain Error <0.04%
Gain Drift < 3ppm/°C
Wide Supply Range: Single 2.7V to Split ±18V
Micropower: 100μA Supply Current
Precision: 50μV Maximum Input Offset Voltage
560kHz Gain Bandwidth Product
Rail-to-Rail Output
Space Saving 10-Lead MSOP and DFN Packages
APPLICATIONS
n
n
n
n
The amplifier features a 50μV maximum input offset voltage and a gain bandwidth product of 560kHz. The device
operates from any supply voltage from 2.7V to 36V and
draws only 100μA supply current on a 5V supply. The
output swings to within 40mV of either supply rail.
The resistors have excellent matching, 0.04% over temperature for the 450k resistors. The matching temperature
coefficent is guaranteed less than 3ppm/°C. The resistors
are extremely linear with voltage, resulting in a gain nonlinearity of less than 10ppm.
The LT1991 is fully specified at 5V and ±15V supplies and
from –40°C to 125°C. The device is available in space
saving 10-lead MSOP and low profile (0.8mm) 3mm ×
3mm DFN packages.
Handheld Instrumentation
Medical Instrumentation
Strain Gauge Amplifiers
Differential to Single-Ended Conversion
L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation.
All other trademarks are the property of their respective owners.
TYPICAL APPLICATION
5V
50k
450k
150k
VM(IN)
–
ΔVIN
VP(IN)
INPUT RANGE
–0.5V TO 5.1V
RIN = 900kΩ
+
450k
–
450k
+
150k
Distribution of Resistor Matching
VOUT = VREF + ΔVIN
SWING 40mV TO
EITHER RAIL
ROUT <0.1Ω
40
35
PERCENTAGE OF UNITS (%)
Rail-to-Rail Gain = 1 Difference Amplifier
4pF
LT1991
450k
450k RESISTORS
LT1991A
30
25
20
15
10
5
50k
0
–0.04
4pF
VREF = 2.5V
1991 TA01
0
–0.02
0.02
RESISTOR MATCHING (%)
0.04
1991 TA01b
1991fg
1
LT1991
ABSOLUTE MAXIMUM RATINGS
(Note 1)
Total Supply Voltage (V+ to V – ) ................................40V
Input Voltage (Pins P1/M1, Note 2) .......................±60V
Input Voltage
(Other Inputs Note 2) ..................V+ + 0.2V to V – – 0.2V
Output Short-Circuit Duration (Note 3) ........... Indefinite
Operating Temperature Range (Note 4)
LT1991C............................................... –40°C to 85°C
LT1991I ................................................ –40°C to 85°C
LT1991H ............................................ –40°C to 125°C
Specified Temperature Range (Note 5)
LT1991C............................................... –40°C to 85°C
LT1991I ................................................ –40°C to 85°C
LT1991H ............................................ –40°C to 125°C
Maximum Junction Temperature
DD Package .......................................................... 125°C
MS Package ......................................................... 150°C
Storage Temperature Range
DD Package............................................ –65°C to 125°C
MS Package ........................................... –65°C to 150°C
Lead Temperature (Soldering, 10 sec) ................. 300°C
PIN CONFIGURATION
TOP VIEW
P1
1
10 M1
P3
2
9 M3
P9
3
8 M9
VEE
4
7 VCC
REF
5
6 OUT
TOP VIEW
P1
P3
P9
VEE
REF
1
2
3
4
5
10
9
8
7
6
M1
M3
M9
VCC
OUT
MS PACKAGE
10-LEAD PLASTIC MSOP
DD PACKAGE
10-LEAD (3mm × 3mm) PLASTIC DFN
EXPOSED PAD CONNECTED TO VEE PCB
CONNECTION OPTIONAL
TJMAX = 150°C, θJA = 230°C/W
TJMAX = 125°C, θJA = 43°C/W
ORDER INFORMATION
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LT1991CDD#PBF
LTCT1991CDD#TRPBF
LBMM
10-Lead (3mm × 3mm) Plastic DFN
–40°C to 85°C
LT1991ACDD#PBF
LT1991ACDD#TRPBF
LBMM
10-Lead (3mm × 3mm) Plastic DFN
–40°C to 85°C
LT1991IDD#PBF
LT1991IDD#TRPBF
LBMM
10-Lead (3mm × 3mm) Plastic DFN
–40°C to 85°C
LT1991AIDD#PBF
LT1991AIDD#TRPBF
LBMM
10-Lead (3mm × 3mm) Plastic DFN
–40°C to 85°C
LT1991HDD#PBF
LT1991HDD#TRPBF
LBMM
10-Lead (3mm × 3mm) Plastic DFN
–40°C to 125°C
LT1991CMS#PBF
LT1991CMS#TRPBF
LTQD
10-Lead Plastic MSOP
–40°C to 85°C
LT1991ACMS#PBF
LT1991ACMS#TRPBF
LTQD
10-Lead Plastic MSOP
–40°C to 85°C
LT1991IMS#PBF
LT1991IMS#TRPBF
LTQD
10-Lead Plastic MSOP
–40°C to 85°C
LT1991AIMS#PBF
LT1991AIMS#TRPBF
LTQD
10-Lead Plastic MSOP
–40°C to 85°C
LT1991HMS#PBF
LT1991HMS#TRPBF
LTQD
10-Lead Plastic MSOP
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *Temperature grades are identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
1991fg
2
LT1991
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the operating
temperature range of 0°C to 70°C for C-grade parts and –40°C to 85°C for I-grade parts, otherwise specifications are at TA = 25°C.
Difference amplifier configuration, VS = 5V, 0V or ±15V; VCM = VREF = half supply, unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
ΔG
Gain Error
VS = ±15V, VOUT = ±10V; RL = 10k
G = 1; LT1991A
G = 1; LT1991
G = 3 or 9; LT1991A
G = 3 or 9; LT1991
l
l
l
l
TYP
MAX
UNITS
±0.04
±0.08
±0.06
±0.12
%
%
%
%
GNL
Gain Nonlinearity
VS = ±15V; VOUT = ±10V; RL = 10k
l
1
10
ppm
ΔG/ΔT
Gain Drift vs Temperature (Note 6)
VS = ±15V; VOUT = ±10V; RL = 10k
l
0.3
3
ppm/°C
CMRR
Common Mode Rejection Ratio,
Referred to Inputs (RTI)
VS = ±15V; VCM = ±15.2V
G = 9; LT1991A
G = 3; LT1991A
G = 1; LT1991A
Any Gain; LT1991
l
l
l
l
80
75
75
60
Input Voltage Range (Note 7)
P1/M1 Inputs
VS = ±15V; VREF = 0V
VS = 5V, 0V; VREF = 2.5V
VS = 3V, 0V; VREF = 1.25V
l
l
l
–28
–0.5
0.75
27.6
5.1
2.35
V
V
V
P1/M1 Inputs, P9/M9 Connected to REF
VS = ±15V; VREF = 0V
VS = 5V, 0V; VREF = 2.5V
VS = 3V, 0V; VREF = 1.25V
l
l
l
–60
–14
–1.5
60
16.8
7.3
V
V
V
P3/M3 Inputs
VS = ±15V; VREF = 0V
VS = 5V, 0V; VREF = 2.5V
VS = 3V, 0V; VREF = 1.25V
l
l
l
–15.2
0.5
0.95
15.2
4.2
1.95
V
V
V
P9/M9 Inputs
VS = ±15V; VREF = 0V
VS = 5V, 0V; VREF = 2.5V
VS = 3V, 0V; VREF = 1.25V
l
l
l
–15.2
0.85
1.0
15.2
3.9
1.9
V
V
V
15
50
135
μV
μV
15
80
160
μV
μV
25
100
200
μV
μV
25
150
250
μV
μV
0.3
1
2.5
5
7.5
nA
nA
50
500
750
pA
pA
50
1000
1500
pA
pA
VCM
VOS
Op Amp Offset Voltage (Note 8)
LT1991AMS, VS = 5V, 0V
LT1991AMS, VS = ±15V
LT1991MS
LT1991DD
ΔVOS/ΔT
Op Amp Offset Voltage Drift (Note 6)
IB
Op Amp Input Bias Current (Note 11)
IOS
Op Amp Input Offset Current (Note 11)
l
l
l
l
l
LT1991A
LT1991
en
l
l
l
100
93
90
70
dB
dB
dB
dB
μV/°C
Op Amp Input Noise Voltage
0.01Hz to 1Hz
0.01Hz to 1Hz
0.1Hz to 10Hz
0.1Hz to 10Hz
0.35
0.07
0.25
0.05
μVP-P
μVRMS
μVP-P
μVRMS
Input Noise Voltage Density
G = 1; f = 1kHz
G = 9; f = 1kHz
180
46
nV/√Hz
nV/√Hz
1991fg
3
LT1991
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the operating
temperature range of 0°C to 70°C for C-grade parts and –40°C to 85°C for I-grade parts, otherwise specifications are at TA = 25°C.
Difference amplifier configuration, VS = 5V, 0V or ±15V; VCM = VREF = half supply, unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
RIN
Input Impedance (Note 10)
P1 (M1 = Ground)
P3 (M3 = Ground)
P9 (M9 = Ground)
l
l
l
630
420
350
900
600
500
1170
780
650
kΩ
kΩ
kΩ
M1 (P1 = Ground)
M3 (P3 = Ground)
M9 (P9 = Ground)
l
l
l
315
105
35
450
150
50
585
195
65
kΩ
kΩ
kΩ
450k Resistors, LT1991A
Other Resistors, LT1991A
450k Resistors, LT1991
Other Resistors, LT1991
l
l
l
l
0.01
0.02
0.02
0.04
0.04
0.06
0.08
0.12
%
%
%
%
0.3
–30
3
ΔR
Resistor Matching (Note 9)
ΔR/ΔT
Resistor Temperature Coefficient (Note 6) Resistor Matching
Absolute Value
l
l
PSRR
Power Supply Rejection Ratio
l
VS = ±1.35V to ±18V (Note 8)
l
Minimum Supply Voltage
135
dB
2.4
2.7
V
40
55
65
110
mV
mV
mV
150
225
275
300
mV
mV
mV
No Load
VS = 5V, 0V
VS = 5V, 0V
VS = ±15V
l
l
1mA Load
VS = 5V, 0V
VS = 5V, 0V
VS = ±15V
l
l
Output Short-Circuit Current (Sourcing)
Drive Output Positive;
Short Output to Ground
l
8
4
12
mA
mA
Output Short-Circuit Current (Sinking)
Drive Output Negative;
Short Output to VS or Midsupply
l
8
4
21
mA
mA
BW
–3dB Bandwidth
G=1
G=3
G=9
110
78
40
kHz
kHz
kHz
GBWP
Op Amp Gain Bandwidth Product
f = 10kHz
560
kHz
tr, tf
Rise Time, Fall Time
G = 1; 0.1V Step; 10% to 90%
G = 9; 0.1V Step; 10% to 90%
3
8
μs
μs
ts
Settling Time to 0.01%
G = 1; VS = 5V, 0V; 2V Step
G = 1; VS = 5V, 0V; –2V Step
G = 1; VS = ±15V, 10V Step
G = 1; VS = ±15V, –10V Step
42
48
114
74
μs
μs
μs
μs
SR
Slew Rate
VS = 5V, 0V; VOUT = 1V to 4V
VS = ±15V; VOUT = ±10V; VMEAS = ±5V
0.12
0.12
V/μs
V/μs
Is
Supply Current
VS = 5V, 0V
VOUT
ISC
Output Voltage Swing (to Either Rail)
105
ppm/°C
ppm/°C
VS = ±15V
l
l
l
l
0.06
0.08
100
110
150
μA
μA
130
160
210
μA
μA
1991fg
4
LT1991
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the operating
temperature range of –40°C to 125°C for H-grade parts, otherwise specifications are at TA = 25°C. Difference amplifier configuration,
VS = 5V, 0V or ±15V; VCM = VREF = half supply, unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
ΔG
Gain Error
VS = ±15V, VOUT = ±10V; RL = 10k
G=1
G = 3 or 9
l
l
TYP
MAX
UNITS
±0.08
±0.12
%
%
GNL
Gain Nonlinearity
VS = ±15V; VOUT = ±10V; RL = 10k
l
1
10
ppm
ΔG/ΔT
Gain Drift vs Temperature (Note 6)
VS = ±15V; VOUT = ±10V; RL = 10k
l
0.3
3
ppm/°C
CMRR
Common Mode Rejection Ratio,
Referred to Inputs (RTI)
VS = ±15V; VCM = ±15.2V
G=9
G=3
G=1
l
l
l
77
70
70
Input Voltage Range (Note 7)
P1/M1 Inputs
VS = ±15V; VREF = 0V
VS = 5V, 0V; VREF = 2.5V
VS = 3V, 0V; VREF = 1.25V
l
l
l
–28
–0.5
0.75
27.6
5.1
2.35
V
V
V
P1/M1 Inputs, P9/M9 Connected to REF
VS = ±15V; VREF = 0V
VS = 5V, 0V; VREF = 2.5V
VS = 3V, 0V; VREF = 1.25V
l
l
l
–60
–14
–1.5
60
16.8
7.3
V
V
V
P3/M3 Inputs
VS = ±15V; VREF = 0V
VS = 5V, 0V; VREF = 2.5V
VS = 3V, 0V; VREF = 1.25V
l
l
l
–15.2
0.5
0.95
15.2
4.2
1.95
V
V
V
P9/M9 Inputs
VS = ±15V; VREF = 0V
VS = 5V, 0V; VREF = 2.5V
VS = 3V, 0V; VREF = 1.25V
l
l
l
–15.2
0.85
1.0
15.2
3.9
1.9
V
V
V
25
100
285
μV
μV
25
150
295
μV
μV
0.3
1
μV/°C
2.5
5
25
nA
nA
50
1000
4500
pA
pA
VCM
VOS
Op Amp Offset Voltage (Note 8)
LT1991MS
LT1991DD
ΔVOS/ΔT
Op Amp Offset Voltage Drift (Note 6)
IB
Op Amp Input Bias Current (Note 11)
IOS
Op Amp Input Offset Current (Note 11)
l
l
l
l
l
100
93
90
dB
dB
dB
Op Amp Input Noise Voltage
0.01Hz to 1Hz
0.01Hz to 1Hz
0.1Hz to 10Hz
0.1Hz to 10Hz
0.35
0.07
0.25
0.05
μVP-P
μVRMS
μVP-P
μVRMS
en
Input Noise Voltage Density
G = 1; f = 1kHz
G = 9; f = 1kHz
180
46
nV/√Hz
nV/√Hz
RIN
Input Impedance (Note 10)
P1 (M1 = Ground)
P3 (M3 = Ground)
P9 (M9 = Ground)
l
l
l
630
420
350
900
600
500
1170
780
650
kΩ
kΩ
kΩ
M1 (P1 = Ground)
M3 (P3 = Ground)
M9 (P9 = Ground)
l
l
l
315
105
35
450
150
50
585
195
65
kΩ
kΩ
kΩ
450k Resistors
Other Resistors
l
l
0.02
0.04
0.08
0.12
%
%
l
l
0.3
–30
3
ΔR
Resistor Matching (Note 9)
ΔR/ΔT
Resistor Temperature Coefficient (Note 6) Resistor Matching
Absolute Value
ppm/°C
ppm/°C
1991fg
5
LT1991
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the operating
temperature range of –40°C to 125°C for H-grade parts, otherwise specifications are at TA = 25°C. Difference amplifier configuration,
VS = 5V, 0V or ±15V; VCM = VREF = half supply, unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
PSRR
Power Supply Rejection Ratio
VS = ±1.35V to ±18V (Note 8)
TYP
105
135
l
Minimum Supply Voltage
MAX
UNITS
dB
2.4
2.7
V
40
55
75
120
mV
mV
mV
150
225
300
340
mV
mV
mV
No Load
VS = 5V, 0V
VS = 5V, 0V
VS = ±15V
l
l
1mA Load
VS = 5V, 0V
VS = 5V, 0V
VS = ±15V
l
l
Output Short-Circuit Current (Sourcing)
Drive Output Positive;
Short Output to Ground
l
8
4
12
mA
mA
Output Short-Circuit Current (Sinking)
Drive Output Negative;
Short Output to VS or Midsupply
l
8
4
21
mA
mA
BW
–3dB Bandwidth
G=1
G=3
G=9
110
78
40
kHz
kHz
kHz
GBWP
Op Amp Gain Bandwidth Product
f = 10kHz
560
kHz
tr, tf
Rise Time, Fall Time
G = 1; 0.1V Step; 10% to 90%
G = 9; 0.1V Step; 10% to 90%
3
8
μs
μs
ts
Settling Time to 0.01%
G = 1; VS = 5V, 0V; 2V Step
G = 1; VS = 5V, 0V; –2V Step
G = 1; VS = ±15V, 10V Step
G = 1; VS = ±15V, –10V Step
42
48
114
74
μs
μs
μs
μs
SR
Slew Rate
VS = 5V, 0V; VOUT = 1V to 4V
VS = ±15V; VOUT = ±10V; VMEAS = ±5V
0.12
0.12
V/μs
V/μs
Is
Supply Current
VS = 5V, 0V
VOUT
ISC
Output Voltage Swing (to Either Rail)
l
MIN
VS = ±15V
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The P3/M3 and P9/M9 inputs should not be taken more than 0.2V
beyond the supply rails. The P1/M1 inputs can withstand ±60V if P9/M9
are grounded and VS = ±15V (see Applications Information section about
“High Voltage CM Difference Amplifiers”).
l
l
0.06
0.08
l
l
100
110
180
μA
μA
130
160
250
μA
μA
Note 6: This parameter is not 100% tested.
Note 7: Input voltage range is guaranteed by the CMRR test at VS = ±15V.
For the other voltages, this parameter is guaranteed by design and through
correlation with the ±15V test. See the Applications Information section to
determine the valid input voltage range under various operating conditions.
Note 3: A heat sink may be required to keep the junction temperature
below absolute maximum ratings.
Note 8: Offset voltage, offset voltage drift and PSRR are defined as
referred to the internal op amp. You can calculate output offset as follows.
In the case of balanced source resistance, VOS,OUT = VOS • NOISEGAIN
+ IOS • 450k + IB • 450k • (1– RP/RN) where RP and RN are the total
resistance at the op amp positive and negative terminal respectively.
Note 4: Both the LT1991C and LT1991I are guaranteed functional over the
–40°C to 85°C temperature range. The LTC1991H is guaranteed functional
over the –40°C to 125°C temperature range.
Note 9: Applies to resistors that are connected to the inverting inputs.
Resistor matching is not tested directly, but is guaranteed by the gain
error test.
Note 5: The LT1991C is guaranteed to meet the specified performance
from 0°C to 70°C and is designed, characterized and expected to meet
specified performance from –40°C to 85°C but is not tested or QA sampled
at these temperatures. The LT1991I is guaranteed to meet specified
performance from –40°C to 85°C. The LT1991H is guaranteed to meet
specified performance from –40°C to 125°C.
Note 10: Input impedance is tested by a combination of direct
measurements and correlation to the CMRR and gain error tests.
Note 11: IB and IOS are tested at VS = 5V, 0V only.
1991fg
6
LT1991
TYPICAL PERFORMANCE CHARACTERISTICS
Output Voltage Swing
vs Temperature
200
Output Voltage Swing
vs Load Current (Output Low)
VCC
VS = 5V, 0V
NO LOAD
OUTPUT VOLTAGE SWING (mV)
175
TA = 85°C
150
TA = 25°C
125
TA = –40°C
100
75
50
60
VEE
–50
0
4
6 8 10 12 14 16 18 20
SUPPLY VOLTAGE (±V)
–25
0
25
50
75
100
TA = 25°C
–500
–600
–700
–800
–900
–1000
0
1
2
3 4 5 6 7
LOAD CURRENT (mA)
8
9
15
10
5
3
4
5
1
125
6 7 8 9 10 11 12 13
GAIN (V/V)
1991 G07
–0.04
2
3
4
5
1991 G05
6 7 8 9 10 11 12 13
GAIN (V/V)
1991 G06
Slew Rate vs Temperature
0.30
0.25
–0.01
–0.03
2
100
0
–750
1
–50
–150
50
25
0
75
TEMPERATURE (°C)
–25
0.01
–0.02
VS = 5V, 0V
REPRESENTATIVE PARTS
0
GAIN = 1
VS = ±15V
VOUT = ±10V
TA = 25°C
0.03
–500
10
50
SLEW RATE (V/μs)
–250
9
–100
0.02
0
8
100
Gain Error vs Load Current
GAIN ERROR (%)
OUTPUT OFFSET VOLTAGE (µV)
SOURCING
0.04
500
–1000
150
20
1991 G04
250
3 4 5 6 7
LOAD CURRENT (mA)
2
1
Input Offset Voltage
vs Difference Gain
VS = 5V, 0V
0
–50
10
VS = 5V, 0V
REPRESENTATIVE PARTS
750
0
1991 G03
SINKING
Output Offset Voltage
vs Difference Gain
1000
VEE
125
INPUT OFFSET VOLTAGE (μV)
OUTPUT SHORT-CIRCUIT CURRENT (mA)
OUTPUT VOLTAGE SWING (mV)
TA = 85°C
–400
TA = –40°C
400
1991 G02
25
TA = –40°C
–300
TA = 25°C
600
Output Short-Circuit Current
vs Temperature
–100
–200
800
TEMPERATURE (°C)
Output Voltage Swing
vs Load Current (Output High)
VS = 5V, 0V
TA = 85°C
1000
200
1991 G01
VCC
VS = 5V, 0V
1200
OUTPUT LOW
(LEFT AXIS)
20
2
–40
–60
25
0
–20
OUTPUT HIGH
(RIGHT AXIS)
40
1400
OUTPUT VOLTAGE (mV)
Supply Current vs Supply Voltage
SUPPLY CURRENT (μA)
(Difference Amplifier Configuration)
GAIN = 1
VS = ±15V
VOUT = ±10V
0.20
SR– (FALLING EDGE)
0.15
SR+ (RISING EDGE)
0.10
0.05
REPRESENTATIVE UNITS
0
1
2
3
LOAD CURRENT (mA)
4
5
1991 G08
0
–50 –25
50
25
75
0
TEMPERATURE (°C)
100
125
1991 G09
1991fg
7
LT1991
TYPICAL PERFORMANCE CHARACTERISTICS
Bandwidth vs Gain
CMRR vs Frequency
120
VS = 5V, 0V
TA = 25°C
110
VS = 5V, 0V
TA = 25°C
GAIN = 9
100
GAIN = 1
90
90
GAIN = 3
CMRR (dB)
60
40
20
70
60
50
1 2
3 4
30
20
20
10
10
100
1k
10k
FREQUENCY (Hz)
VS = 5V, 0V
TA = 25°C
GAIN = 1
VS = ±15V
GAIN ERROR (%)
CMRR (dB)
GAIN = 1
60
40
0.1
0
–50 –25
0.01
10
100
1k
FREQUENCY (Hz)
10k
100k
REPRESENTATIVE UNITS
50
25
75
0
TEMPERATURE (°C)
100
1991 G13
20
Gain and Phase vs Frequency
2
VS = 5V, 0V
TA = 25°C
VS = 5V, 0V
TA = 25°C 0
GAIN = 1
1 PHASE
GAIN = 9
0
GAIN (dB)
GAIN (dB)
GAIN = 3
GAIN = 1
–10
GAIN
–45
–2
–90
–3
–4
–135
–6
–180
–7
1
10
100
FREQUENCY (kHz)
600
1991 G16
REPRESENTATIVE UNITS
50
25
75
0
TEMPERATURE (°C)
100
–8
0.5
1
10
FREQUENCY (kHz)
100
125
0.01Hz to 1Hz Voltage Noise
–5
–20
0.010
1991 G15
PHASE (deg)
0
0.015
0
–50 –25
125
–1
10
0.020
1991 G14
Gain vs Frequency
30
GAIN = 1
VS = ±15V
0.005
20
1
100k
0.025
80
GAIN = 3
1
1k
10k
FREQUENCY (Hz)
Gain Error vs Temperature
0.030
100
100
GAIN = 9
100
1991 G12
CMRR vs Temperature
120
10
10
1991 G11
Output Impedance vs Frequency
OUTPUT IMPEDANCE (Ω)
0
1M
100k
1991 G10
1000
50
40
10
GAIN = 3
60
30
5 6 7 8 9 10 11 12 13
GAIN SETTING (V/V)
GAIN = 1
70
40
0
GAIN = 9
80
PSRR (dB)
80
80
VS = 5V, 0V
TA = 25°C
110
100
100
–3dB BANDWIDTH (kHz)
PSRR vs Frequency
120
400
VS = ±15V
TA = 25°C
MEASURED IN G =13
REFERRED TO OP AMP INPUTS
OP AMP VOLTAGE NOISE (100nV/DIV)
120
0
(Difference Amplifier Configuration)
0
10 20 30 40 50 60 70 80 90 100
TIME (s)
1991 G17
1991 G21
1991fg
8
LT1991
TYPICAL PERFORMANCE CHARACTERISTICS
Small Signal Transient Response
Small Signal Transient Response
Small Signal Transient Response
GAIN = 9
GAIN = 3
GAIN = 1
50mV/DIV
50mV/DIV
50mV/DIV
1991 G18
5μs/DIV
PIN FUNCTIONS
1991 G19
5μs/DIV
5μs/DIV
1991 G20
(Difference Amplifier Configuration)
P1 (Pin 1): Noninverting Gain-of-1 input. Connects a 450k
internal resistor to the op amp’s noninverting input.
OUT (Pin 6): Output. VOUT = VREF + 1 • (VP1 – VM1) + 3 •
(VP3 – VM3) + 9 • (VP9 – VM9).
P3 (Pin 2): Noninverting Gain-of-3 input. Connects a 150k
internal resistor to the op amp’s noninverting input.
VCC (Pin 7): Positive Power Supply. Can be anything from
2.7V to 36V above the VEE voltage.
P9 (Pin 3): Noninverting Gain-of-9 input. Connects a 50k
internal resistor to the op amp’s noninverting input.
M9 (Pin 8): Inverting Gain-of-9 input. Connects a 50k
internal resistor to the op amp’s inverting input.
VEE (Pin 4): Negative Power Supply. Can be either ground
(in single supply applications), or a negative voltage (in
split supply applications).
M3 (Pin 9): Inverting Gain-of-3 input. Connects a 150k
internal resistor to the op amp’s inverting input.
REF (Pin 5): Reference Input. Sets the output level when
difference between inputs is zero. Connects a 450k internal
resistor to the op amp’s noninverting input.
M1 (Pin 10): Inverting Gain-of-1 input. Connects a 450k
internal resistor to the op amp’s inverting input.
Exposed Pad: Must be soldered to PCB.
BLOCK DIAGRAM
M1
M3
M9
VCC
10
9
8
7
OUT
6
50k
450k
150k
4pF
450k
INM
OUT
450k
INP
LT1991
150k
450k
50k
4pF
1
2
3
4
5
P1
P3
P9
VEE
REF
1991 BD
1991fg
9
LT1991
APPLICATIONS INFORMATION
Introduction
The LT1991 may be the last op amp you ever have to stock.
Because it provides you with several precision matched
resistors, you can easily configure it into several different
classical gain circuits without adding external components.
The several pages of simple circuits in this data sheet
demonstrate just how easy the LT1991 is to use. It can
be configured into difference amplifiers, as well as into
inverting and noninverting single ended amplifiers. The
fact that the resistors and op amp are provided together
in such a small package will often save you board space
and reduce complexity for easy probing.
The Op Amp
The op amp internal to the LT1991 is a precision device
with 15μV typical offset voltage and 3nA input bias current.
The input offset current is extremely low, so matching the
source resistance seen by the op amp inputs will provide
for the best output accuracy. The op amp inputs are not
rail-to-rail, but extend to within 1.2V of VCC and 1V of
VEE. For many configurations though, the chip inputs will
function rail-to-rail because of effective attenuation to the
+input. The output is truly rail-to-rail, getting to within
40mV of the supply rails. The gain bandwidth product of
the op amp is about 560kHz. In noise gains of 2 or more,
it is stable into capacitive loads up to 500pF. In noise gains
below 2, it is stable into capacitive loads up to 100pF.
The Resistors
The resistors internal to the LT1991 are very well matched
SiChrome based elements protected with barrier metal.
Although their absolute tolerance is fairly poor (±30%),
their matching is to within 0.04%. This allows the chip to
achieve a CMRR of 75dB, and gain errors within 0.04%.
The resistor values are 50k, 150k, and 2 of 450k, connected to each of the inputs. The resistors have power
limitations of 1watt for the 450k resistors, 0.3watt for the
150k resistors and 0.5watt for the 50k resistors; however,
in practice, power dissipation will be limited well below
these values by the maximum voltage allowed on the
input and REF pins. The 450k resistors connected to the
M1 and P1 inputs are isolated from the substrate, and can
therefore be taken beyond the supply voltages. The naming
of the pins “P1,” “P3,” “P9,” etc., is based on their relative
admittances. Because it has 9 times the admittance, the
voltage applied to the P9 input has 9 times the effect of
the voltage applied to the P1 input.
Bandwidth
The bandwidth of the LT1991 will depend on the gain you
select (or more accurately the noise gain resulting from
the gain you select). In the lowest configurable gain of 1,
the –3dB bandwidth is limited to 450kHz, with peaking of
about 2dB at 280kHz. In the highest configurable gains,
bandwidth is limited to 32kHz.
Input Noise
The LT1991 input noise is dominated by the Johnson
noise of the internal resistors (√4kTR). Paralleling all
four resistors to the +input gives a 32.1kΩ resistance, for
23nV/√Hz of voltage noise. The equivalent network on the
–input gives another 23nV/√Hz , and taking their RMS sum
gives a total 33nV/√Hz input referred noise floor. Output
noise depends on configuration and noise gain.
Input Resistance
The LT1991 input resistances vary with configuration, but
once configured are apparent on inspection. Note that
resistors connected to the op amp’s –input are looking
into a virtual ground, so they simply parallel. Any feedback
resistance around the op amp does not contribute to input
resistance. Resistors connected to the op amp’s +input
are looking into a high impedance, so they add as parallel or series depending on how they are connected, and
whether or not some of them are grounded. The op amp
+input itself presents a very high GΩ impedance. In the
classical noninverting op amp configuration, the LT1991
presents the high input impedance of the op amp, as is
usual for the noninverting case.
Common Mode Input Voltage Range
The LT1991 valid common mode input range is limited
by three factors:
1. Maximum allowed voltage on the pins
2. The input voltage range of the internal op amp
3. Valid output voltage
1991fg
10
LT1991
APPLICATIONS INFORMATION
The maximum voltage allowed on the P3, M3, P9, and
M9 inputs includes the positive and negative supply plus
a diode drop. These pins should not be driven more than
0.2V outside of the supply rails. This is because they are
connected through diodes to internal manufacturing postpackage trim circuitry, and through a substrate diode to
VEE. If more than 10mA is allowed to flow through these
pins, there is a risk that the LT1991 will be detrimmed or
damaged. The P1 and M1 inputs do not have clamp diodes
or substrate diodes or trim circuitry and can be taken well
outside the supply rails. The maximum allowed voltage on
the P1 and M1 pins is ±60V.
The input voltage range of the internal op amp extends
to within 1.2V of VCC and 1V of VEE. The voltage at which
the op amp inputs common mode is determined by the
voltage at the op amp’s +input, and this is determined by
the voltages on pins P1, P3, P9 and REF (see “Calculating
Input Voltage Range” section). This is true provided that
the op amp is functioning and feedback is maintaining the
inputs at the same voltage, which brings us to the third
requirement.
For valid circuit function, the op amp output must not be
clipped. The output will clip if the input signals are attempting to force it to within 40mV of its supply voltages. This
usually happens due to too large a signal level, but it can
also occur with zero input differential and must therefore
be included as an example of a common mode problem.
Consider Figure 1. This shows the LT1991 configured
as a gain of 13 difference amplifier on a single supply
with the output REF connected to ground. This is a great
circuit, but it does not support VDM = 0V at any common
mode because the output clips into ground while trying
to produce 0VOUT. It can be fixed simply by declaring the
valid input differential range not to extend below +4mV,
or by elevating the REF pin above 40mV, or by providing
a negative supply.
Calculating Input Voltage Range
Figure 2 shows the LT1991 in the generalized case of
a difference amplifier, with the inputs shorted for the
common mode calculation. The values of RF and RG are
dictated by how the P inputs and REF pin are connected.
By superposition we can write:
VINT = VEXT • (RF/(RF + RG)) + VREF • (RG/(RF + RG))
Or, solving for VEXT :
VEXT = VINT • (1 + RG/RF) – VREF • RG/RF
But valid VINT voltages are limited to VCC – 1.2V and VEE
+ 1V, so:
MAX VEXT = (VCC – 1.2) • (1 + RG/RF) – VREF • RG/RF
and:
MIN VEXT = (VEE + 1) • (1 + RG/RF) – VREF • RG/RF
RF
5V
8
50k
9
150k
10
450k
–
VCM
2.5V
1
450k
2
150k
3
50k
–
450k
VEXT
4pF
VDM
0V+
VCC
RG
7
VINT
RG
+
VEE
VREF
RF
–
6
VOUT = 13 • VDM
+
1991 F02
Figure 2. Calculating CM Input Voltage Range
4pF
450k
REF 5
LT1991
4
1991 F01
Figure 1. Difference Amplifier Cannot Produce
0V on a Single Supply. Provide a Negative
Supply, or Raise Pin 5, or Provide 4mV of VDM
These two voltages represent the high and low extremes
of the common mode input range, if the other limits have
not already been exceeded (1 and 3, above). In most
cases, the inverting inputs M1 through M9 can be taken
further than these two extremes because doing this does
not move the op amp input common mode. To calculate
the limit on this additional range, see Figure 3. Note that,
1991fg
11
LT1991
APPLICATIONS INFORMATION
with VMORE = 0, the op amp output is at VREF. From the
max VEXT (the high cm limit), as VMORE goes positive, the
op amp output will go more negative from VREF by the
amount VMORE • RF/RG, so:
VOUT = VREF – VMORE • RF/RG
Or:
VMORE = (VREF – VOUT) • RG/RF
The most negative that VOUT can go is VEE + 0.04V, so:
Max VMORE = (VREF – VEE – 0.04V) • RG/RF
(should be positive)
The situation where this function is negative, and therefore problematic, when VREF = 0 and VEE = 0, has already
been dealt with in Figure 1. The strength of the equation
is demonstrated in that it provides the three solutions
suggested in Figure 1: raise VREF , lower VEE, or provide
some negative VMORE.
representation of the circuit on the top. The LT1991 is
shown on the bottom configured in a precision gain of 5.5.
One of the benefits of the noninverting op amp configuration is that the input impedance is extremely high. The
LT1991 maintains this benefit. Given the finite number of
available feedback resistors in the LT1991, the number of
gain configurations is also finite. The complete list of such
Hi-Z input noninverting gain configurations is shown in
Table 1. Many of these are also represented in Figure 5 in
schematic form. Note that the P-side resistor inputs have
been connected so as to match the source impedance
seen by the internal op amp inputs. Note also that gain
and noise gain are identical, for optimal precision.
RF
RG
–
VOUT
VIN
Likewise, from the lower common mode extreme, making the negative input more negative will raise the output
voltage, limited by VCC – 0.04V.
+
VOUT = GAIN • VIN
GAIN = 1 + RF/RG
CLASSICAL NONINVERTING OP AMP CONFIGURATION.
YOU PROVIDE THE RESISTORS.
MIN VMORE = (VREF – VCC + 0.04V) • RG/RF
(should be negative)
RF
8
50k
9
150k
10
450k
1
450k
2
150k
3
50k
450k
4pF
VCC
RG
–
VMORE
VEXT
MAX OR MIN
VINT
RG
+
VEE
VREF
RF
1991 F03
Figure 3. Calculating Additional
Voltage Range of Inverting Inputs
–
6
VOUT
+
4pF
450k
LT1991
Again, the additional input range calculated here is only
available provided the other remaining constraint is not
violated, the maximum voltage allowed on the pin.
The Classical Noninverting Amplifier: High Input Z
Perhaps the most common op amp configuration is the
noninverting amplifier. Figure 4 shows the textbook
5
VIN
CLASSICAL NONINVERTING OP AMP CONFIGURATION
IMPLEMENTED WITH LT1991. RF = 225k, RG = 50k, GAIN = 5.5.
GAIN IS ACHIEVED BY GROUNDING, FLOATING OR FEEDING BACK
THE AVAILABLE RESISTORS TO ARRIVE AT DESIRED RF AND RG.
WE PROVIDE YOU WITH <0.1% RESISTORS.
1991 F04
Figure 4. The LT1991 as a Classical Noninverting Op Amp
1991fg
12
LT1991
APPLICATIONS INFORMATION
Table 1. Configuring the M Pins for Simple Noninverting Gains.
The P Inputs are driven as shown in the examples on the
next page.
M9, M3, M1 Connection
Gain
M9
M3
M1
1
Output
Output
Output
1.077
Output
Output
Ground
1.1
Output
Float
Ground
1.25
Float
Output
Ground
1.273
Output
Ground
Output
1.3
Output
Ground
Float
1.4
Output
Ground
Ground
2
Float
Float
Ground
2.5
Float
Ground
Output
2.8
Ground
Output
Output
3.25
Ground
Output
Float
3.5
Ground
Output
Ground
4
Float
Ground
Float
5
Float
Ground
Ground
5.5
Ground
Float
Output
7
Ground
Ground
Output
10
Ground
Float
Float
11
Ground
Float
Ground
13
Ground
Ground
Float
14
Ground
Ground
Ground
1991fg
13
LT1991
APPLICATIONS INFORMATION
VS+
8
M9
9
M3
10
M1
VIN
1
P1
2
P3
3
P9
VS+
8
M9
9
M3
10
M1
7
VCC
LT1991
VEE
OUT
REF
5
6
VOUT
1
P1
2
P3
3
P9
VIN
4
VS–
7
VCC
LT1991
VEE
6
VOUT
VIN
4
LT1991
VEE
OUT
REF
5
6
VOUT
1
P1
2
P3
3
P9
4
VS–
VS+
7
VCC
LT1991
VEE
OUT
REF
5
6
VOUT
1
P1
2
P3
3
P9
4
VS+
7
VCC
VEE
7
VCC
LT1991
VEE
VOUT
1
P1
2
P3
3
P9
VIN
4
OUT
REF
5
6
VOUT
4
VS–
GAIN = 5.5
VS+
8
M9
9
M3
10
M1
6
VOUT
4
8
M9
9
M3
10
M1
GAIN = 5
OUT
REF
5
6
VIN
GAIN = 4
VIN
VEE
OUT
REF
5
GAIN = 3.25
VIN
LT1991
LT1991
VS–
VS–
VIN
1
P1
2
P3
3
P9
7
VCC
VS+
8
M9
9
M3
10
M1
7
VCC
8
M9
9
M3
10
M1
1
P1
2
P3
3
P9
GAIN = 2
VS+
1
P1
2
P3
3
P9
OUT
REF
5
VS–
GAIN = 1
8
M9
9
M3
10
M1
VS+
8
M9
9
M3
10
M1
VS–
VS+
8
M9
9
M3
10
M1
7
VCC
LT1991
VEE
OUT
REF
5
6
VOUT
1
P1
2
P3
3
P9
4
VS–
7
VCC
LT1991
VEE
OUT
REF
5
6
VOUT
4
VS–
VIN
GAIN = 7
GAIN = 10
GAIN = 11
VS+
8
M9
9
M3
10
M1
VIN
1
P1
2
P3
3
P9
VS+
8
M9
9
M3
10
M1
7
VCC
LT1991
VEE
OUT
REF
5
6
VOUT
1
P1
2
P3
3
P9
4
VS–
7
VCC
LT1991
VEE
OUT
REF
5
6
VOUT
4
VS–
VIN
GAIN = 13
GAIN = 14
1991 F05
Figure 5. Some Implementations of Classical Noninverting
Gains Using the LT1991. High Input Z Is Maintained.
1991fg
14
LT1991
APPLICATIONS INFORMATION
Attenuation Using the P Input Resistors
Attenuation happens as a matter of fact in difference
amplifier configurations, but it is also used for reducing
peak signal level or improving input common mode range
even in single ended systems. When signal conditioning
indicates a need for attenuation, the LT1991 resistors are
ready at hand. The four precision resistors can provide
several attenuation levels, and these are tabulated in
Table 2 as a design reference.
VIN
VIN
OKAY UP
TO ±60V
RA
VINT
RG
VINT = A • VIN
A = RG/(RA + RG)
1
450k
2
150k
3
50k
VINT
+
4pF
450k
LT1991
5
CLASSICAL ATTENUATOR
LT1991 ATTENUATING TO THE +INPUT BY
DRIVING AND GROUNDING AND FLOATING
INPUTS RA = 450k, RG = 50k, SO A = 0.1.
1991 F06
Figure 6. LT1991 Provides for Easy Attenuation to the Op Amp’s
+Input. The P1 Input Can Be Taken Well Outside of the Supplies.
Because the attenuations and the noninverting gains are set
independently, they can be combined. This provides high
gain resolution, about 340 unique gains between 0.077
and 14, as plotted in Figure 7. This is too large a number
to tabulate, but the designer can calculate achievable gain
by taking the vector product of the gains and attenuations
in Tables 1 and 2, and seeking the best match. Average
gain resolution is 1.5%, with a worst-case of 7%.
100
GAIN
10
Table 2. Configuring the P Pins for Various Attenuations.
Those Shown in Bold Are Functional Even When the Input Drive
Exceeds the Supplies.
P9, P3, P1, REF Connection
A
P9
P3
P1
REF
0.0714
Ground
Ground
Drive
Ground
0.0769
Ground
Ground
Drive
Float
0.0909
Ground
Float
Drive
Ground
0.1
Ground
Float
Drive
Float
0.143
Ground
Ground
Drive
Drive
0.182
Ground
Float
Drive
Drive
0.2
Float
Ground
Drive
Ground
0.214
Ground
Drive
Ground
Ground
0.231
Ground
Drive
Float
Ground
0.25
Float
Ground
Drive
Float
0.286
Ground
Drive
Drive
Ground
0.308
Ground
Drive
Drive
Float
0.357
Ground
Drive
Drive
Drive
0.4
Float
Ground
Drive
Drive
0.5
Float
Float
Drive
Ground
0.6
Float
Drive
Ground
Ground
0.643
Drive
Ground
Ground
Ground
0.692
Drive
Ground
Float
Ground
0.714
Drive
Ground
Drive
Ground
0.75
Float
Drive
Float
Ground
0.769
Drive
Ground
Drive
Float
0.786
Drive
Ground
Drive
Drive
0.8
Float
Drive
Drive
Ground
0.818
Drive
Float
Ground
Ground
0.857
Drive
Drive
Ground
Ground
0.9
Drive
Float
Float
Ground
0.909
Drive
Float
Drive
Ground
0.923
Drive
Drive
Float
Ground
0.929
Drive
Drive
Drive
Ground
1
Drive
Drive
Drive
Drive
1
0.1
0.01
0
50
100
150 200
COUNT
250
300
350
1991 F07
Figure 7. Over 346 Unique Gain Settings Achievable with the
LT1991 by Combining Attenuation with Noninverting Gain
1991fg
15
LT1991
APPLICATIONS INFORMATION
Inverting Configuration
Table 3. Configuring the M Pins for Simple Inverting Gains
The inverting amplifier, shown in Figure 8, is another
classical op amp configuration. The circuit is actually
identical to the noninverting amplifier of Figure 4, except
that VIN and GND have been swapped. The list of available gains is shown in Table 3, and some of the circuits
are shown in Figure 9. Noise gain is 1+|Gain|, as is the
usual case for inverting amplifiers. Again, for the best DC
performance, match the source impedance seen by the
op amp inputs.
RF
RG
VIN
–
VOUT
+
VOUT = GAIN • VIN
GAIN = – RF/RG
CLASSICAL INVERTING OP AMP CONFIGURATION.
YOU PROVIDE THE RESISTORS.
VIN
(DRIVE)
8
50k
9
150k
10
450k
1
450k
2
150k
3
50k
450k
M9, M3, M1 Connection
Gain
M9
M3
M1
–0.077
Output
Output
Drive
–0.1
Output
Float
Drive
–0.25
Float
Output
Drive
–0.273
Output
Drive
Output
–0.3
Output
Drive
Float
–0.4
Output
Drive
Drive
–1
Float
Float
Drive
–1.5
Float
Drive
Output
–1.8
Drive
Output
Output
–2.25
Drive
Output
Float
–2.5
Drive
Output
Drive
–3
Float
Drive
Float
–4
Float
Drive
Drive
–4.5
Drive
Float
Output
–6
Drive
Drive
Output
–9
Drive
Float
Float
–10
Drive
Float
Drive
–12
Drive
Drive
Float
–13
Drive
Drive
Drive
4pF
–
6
VOUT
+
4pF
450k
LT1991
5
CLASSICAL INVERTING OP AMP CONFIGURATION IMPLEMENTED
WITH LT1991. RF = 225k, RG = 50k, GAIN = –4.5.
GAIN IS ACHIEVED BY GROUNDING, FLOATING OR FEEDING BACK
THE AVAILABLE RESISTORS TO ARRIVE AT DESIRED RF AND RG.
WE PROVIDE YOU WITH <0.1% RESISTORS.
1991 F08
Figure 8. The LT1991 as a Classical Inverting Op Amp.
Note the Circuit Is Identical to the Noninverting Amplifier,
Except that VIN and Ground Have Been Swapped.
1991fg
16
LT1991
APPLICATIONS INFORMATION
VS+
8
M9
9
M3
10
M1
VIN
1
P1
2
P3
3
P9
VS+
7
VCC
LT1991
VEE
OUT
REF
5
6
8
M9
9
M3
10
M1
VIN
VOUT
1
P1
2
P3
3
P9
4
VS–
LT1991
VEE
1
P1
2
P3
3
P9
LT1991
VEE
OUT
REF
5
6
VIN
VOUT
1
P1
2
P3
3
P9
4
VEE
LT1991
VEE
OUT
REF
5
6
VOUT
1
P1
2
P3
3
P9
4
VIN
OUT
REF
5
6
VOUT
8
M9
9
M3
10
M1
1
P1
2
P3
3
P9
7
VCC
LT1991
VEE
VS–
VS+
VIN
LT1991
OUT
REF
5
6
VOUT
1
P1
2
P3
3
P9
4
1
P1
2
P3
3
P9
VEE
OUT
REF
5
4
LT1991
VEE
OUT
REF
5
6
VOUT
4
GAIN = –10
VS+
7
VCC
LT1991
7
VCC
VS–
VS+
VIN
VOUT
4
8
M9
9
M3
10
M1
GAIN = –9
8
M9
9
M3
10
M1
6
GAIN = –4.5
VS–
GAIN = –6
OUT
REF
5
VS–
7
VCC
VEE
VOUT
4
VS+
VIN
6
VS+
4
8
M9
9
M3
10
M1
OUT
REF
5
GAIN = –2.25
GAIN = –4
7
VCC
LT1991
LT1991
VS–
7
VCC
VS+
VEE
1
P1
2
P3
3
P9
VS–
GAIN = –3
1
P1
2
P3
3
P9
VOUT
7
VCC
VS+
8
M9
9
M3
10
M1
VS–
VIN
6
GAIN = –1
7
VCC
8
M9
9
M3
10
M1
OUT
REF
5
4
VS+
VIN
VIN
7
VCC
VS–
GAIN = –0.25
8
M9
9
M3
10
M1
VS+
8
M9
9
M3
10
M1
6
VIN
VOUT
8
M9
9
M3
10
M1
1
P1
2
P3
3
P9
7
VCC
LT1991
VEE
OUT
REF
5
6
VOUT
4
VS–
VS–
GAIN = –12
GAIN = –13
1991 F09
Figure 9. It Is Simple to Get Precision Inverting Gains with the LT1991.
Input Impedance Varies from 45kΩ (Gain = –13) to 450kΩ (Gain = –1).
1991fg
17
LT1991
APPLICATIONS INFORMATION
Difference Amplifiers
RF
The resistors in the LT1991 allow it to easily make difference amplifiers also. Figure 10 shows the basic 4-resistor
difference amplifier and the LT1991. A difference gain of
3 is shown, but notice the effect of the additional dashed
connections. By connecting the 450k resistors in parallel, the gain is reduced by a factor of 2. Of course, with
so many resistors, there are many possible gains. Table
4 shows the difference gains and how they are achieved.
Note that, as for inverting amplifiers, the noise gain is 1
more than the signal gain.
VIN–
VIN+
RG
RG
–
VOUT
+
RF
CLASSICAL DIFFERENCE AMPLIFIER USING THE LT1991
8 M9 50k
Table 4. Connections Giving Difference Gains for the LT1991
Gain
VIN+
VIN–
Output
GND (REF)
0.077
P1
M1
M3, M9
P3, P9
0.1
P1
M1
M9
P9
0.25
P1
M1
M3
P3
0.273
P3
M3
M1, M9
P1, P9
0.3
P3
M3
M9
P9
0.4
P1, P3
M1, M3
M9
P9
P1
M1
1.5
P3
M3
M1
P1
1.8
P9
M9
M1, M3
P1, P3
2.25
P9
M9
M3
P3
2.5
P1, P9
M1, M9
M3
P3
3
P3
M3
4
P1, P3
M1, M3
4.5
P9
M9
M1
P1
6
P3, P9
M3, M9
M1
P1
9
P9
M9
P1, P9
M1, M9
12
P3, P9
M3, M9
13
P1, P3, P9
M1, M3, M9
VIN–
VIN+
4pF
9 M3 150k
10 M1 450k
PARALLEL
TO CHANGE
RF, RG
450k
1 P1
450k
2 P3
150k
3 P9
50k
–
6
VOUT
+
4pF
450k
5
LT1991
1
10
VOUT = GAIN • (VIN+ – VIN–)
GAIN = RF/RG
CLASSICAL DIFFERENCE AMPLIFIER IMPLEMENTED
WITH LT1991. RF = 450k, RG = 150k, GAIN = 3.
ADDING THE DASHED CONNECTIONS CONNECTS THE
TWO 450k RESISTORS IN PARALLEL, SO RF IS REDUCED
TO 225k. GAIN BECOMES 225k/150k = 1.5.
1991 F10
Figure 10. Difference Amplifier Using the LT1991. Gain Is Set
Simply by Connecting the Correct Resistors or Combinations
of Resistors. Gain of 3 Is Shown, with Dashed Lines Modifying
It to Gain of 1.5. Noise Gain Is Optimal.
1991fg
18
LT1991
APPLICATIONS INFORMATION
VS+
VIN
VIN
8
M9
9
M3
10
M1
–
1
P1
2
P3
3
P9
+
VS+
7
VCC
LT1991
VEE
8
M9
9
M3
10
M1
–
OUT
REF
5
6
VIN
VOUT
1
P1
2
P3
3
P9
+
VIN
4
VS–
LT1991
VEE
VIN+
1
P1
2
P3
3
P9
LT1991
VEE
OUT
REF
5
6
VIN–
8
M9
9
M3
10
M1
VIN+
1
P1
2
P3
3
P9
VOUT
4
VEE
VEE
6
VOUT
1
P1
2
P3
3
P9
VIN+
4
LT1991
VEE
VIN
OUT
REF
5
6
VOUT
VIN+
4
8
M9
9
M3
10
M1
1
P1
2
P3
3
P9
7
VCC
LT1991
VEE
VS–
4
LT1991
OUT
REF
5
6
VOUT
VIN+
4
8
M9
9
M3
10
M1
1
P1
2
P3
3
P9
VIN+
1
P1
2
P3
3
P9
VEE
OUT
REF
5
4
VS–
GAIN = 12
LT1991
VEE
OUT
REF
5
6
VOUT
4
GAIN = 10
VS+
VIN–
7
VCC
LT1991
7
VCC
VS–
GAIN = 9
8
M9
9
M3
10
M1
VOUT
VS+
VIN–
VS+
VIN–
6
GAIN = 4.5
VS–
GAIN = 6
OUT
REF
5
VS–
7
VCC
VEE
VOUT
4
VS+
OUT
REF
5
6
VS+
7
VCC
8
M9
9
M3
10
M1
VIN–
OUT
REF
5
GAIN = 2.25
GAIN = 4
7
VCC
LT1991
LT1991
VS–
–
VS+
VIN+
VIN+
1
P1
2
P3
3
P9
VS–
GAIN = 3
1
P1
2
P3
3
P9
VOUT
7
VCC
VS+
7
VCC
8
M9
9
M3
10
M1
6
GAIN = 1
VS–
VIN–
OUT
REF
5
4
VS+
VIN–
VIN
7
VCC
8
M9
9
M3
10
M1
VS–
GAIN = 0.25
8
M9
9
M3
10
M1
VS+
–
6
VOUT
VIN+
8
M9
9
M3
10
M1
1
P1
2
P3
3
P9
7
VCC
LT1991
VEE
OUT
REF
5
6
VOUT
4
VS–
GAIN = 13
1991 F11
Figure 11. Many Difference Gains Are Achievable Just by Strapping the Pins
1991fg
19
LT1991
APPLICATIONS INFORMATION
8 M9 50k
VIN–
VIN+
RG
RG
4pF
9 M3 150k
VIN–
RF
450k
10 M1 450k
CROSSCOUPLING
–
VOUT
+
VIN+
VOUT = GAIN • (VIN+ – VIN–)
GAIN = RF/RG
RF
1 P1
450k
2 P3
150k
3 P9
50k
–
6
VOUT
+
4pF
450k
5
LT1991
CLASSICAL DIFFERENCE AMPLIFIER IMPLEMENTED
WITH LT1991. RF = 450k, RG = 150k, GAIN = 3.
GAIN CAN BE ADJUSTED BY "CROSS COUPLING." MAKING THE
DASHED CONNECTIONS REDUCE THE GAIN FROM 3 T0 2.
WHEN CROSS COUPLING, SEE WHAT IS CONNECTED TO THE
VIN+ VOLTAGE. CONNECTING P3 AND M1 GIVES +3 –1 = 2.
CONNECTIONS TO VIN– ARE SYMMETRIC: M3 AND P1.
CLASSICAL DIFFERENCE AMPLIFIER
1991 F12
Figure 12. Another Method of Selecting Difference Gain Is “Cross-Coupling.”
The Additional Method Means the LT1991 Provides All Integer Gains from 1 to 13.
Difference Amplifier: Additional Integer Gains Using
Cross-Coupling
Figure 12 shows the basic difference amplifier as well as
the LT1991 in a difference gain of 3. But notice the effect
of the additional dashed connections. This is referred to
as “cross-coupling” and has the effect of reducing the
differential gain from 3 to 2. Using this method, additional
integer gains are achievable, as shown in Table 5 below,
so that all integer gains from 1 to 13 are achieved with the
LT1991. Note that the equations can be written by inspection
from the VIN+ connections, and that the VIN– connections
are simply the opposite (swap P for M and M for P). Noise
gain, bandwidth, and input impedance specifications for the
various cases are also tabulated, as these are not obvious.
Schematics are provided in Figure 13.
VS+
VIN–
8
M9
9
M3
10
M1
VIN+
1
P1
2
P3
3
P9
7
VCC
LT1991
VEE
Gain
VIN+
VIN–
2
P3, M1
M3, P1
5
6*
7
8
3–1
P9, M3, M1 M9, P3, P1 9 – 3 – 1
P9, M3
M9, P3
9–3
P9, P1, M3 M9, M1, P3 9 + 1 – 3
P9, M1
M9, P1
9–1
11 P9, P3, M1 M9, M3, P1 9 + 3 – 1
6
VOUT
1
P1
2
P3
3
P9
VIN+
VS–
7
VCC
LT1991
VEE
VIN+
1
P1
2
P3
3
P9
VOUT
GAIN = 5
VS+
8
M9
9
M3
10
M1
6
4
GAIN = 2
VIN–
OUT
REF
5
VS–
VS+
LT1991
VEE
OUT
REF
5
8
M9
9
M3
10
M1
VIN–
7
VCC
6
VOUT
1
P1
2
P3
3
P9
VIN+
4
VS–
7
VCC
LT1991
VEE
OUT
REF
5
6
VOUT
4
VS–
GAIN = 7
GAIN = 8
VS+
VIN–
–
Noise –3dB BW RIN
RIN
kHz Typ kΩ Typ kΩ
Equation Gain
OUT
REF
5
4
Table 5. Connections Using Cross-Coupling. Note That Equations Can
Be Written by Inspection of the VIN+ Column
+
VS+
8
M9
9
M3
10
M1
VIN–
VIN+
8
M9
9
M3
10
M1
1
P1
2
P3
3
P9
7
VCC
LT1991
VEE
OUT
REF
5
6
VOUT
4
5
70
281
141
VS–
14
32
97
49
GAIN = 11
13
35
122
49
14
32
121
44
11
38
248
50
14
32
242
37
1991 F13
Figure 13. Integer Gain Difference
Amplifiers Using Cross-Coupling
*Gain of 6 is better implemented as shown previously, but is included here for completeness.
1991fg
20
LT1991
APPLICATIONS INFORMATION
High Voltage CM Difference Amplifiers
This class of difference amplifier remains to be discussed.
Figure 14 shows the basic circuit on the top. The effective
input voltage range of the circuit is extended by the fact
that resistors RT attenuate the common mode voltage seen
by the op amp inputs. For the LT1991, the most useful
resistors for RG are the M1 and P1 450kΩ resistors, because they do not have diode clamps to the supplies and
therefore can be taken outside the supplies. As before, the
input CM of the op amp is the limiting factor and is set by
the voltage at the op amp +input, VINT. By superposition
we can write:
VINT = VEXT • (RF||RT)/(RG + RF||RT) + VREF • (RG||RT)/
(RF + RG||RT) + VTERM • (RF||RG)/(RT + RF||RG)
Solving for VEXT :
Table 6. HighV CM Connections Giving Difference Gains for
the LT1991
MIN VEXT = 11 • (VEE + 1V) – VREF – 9 • VTERM
= 11 • (1V) – 2.5 – 9 • 12 = –99.5V
but this exceeds the 60V absolute maximum rating of
the P1, M1 pins, so –60V becomes the de facto negative common mode limit. Several more examples of high
CM circuits are shown in Figures 15, 16, 17 for various
supplies.
2 • VLIM - VREF
5
5 • VLIM – VREF – 3 • VTERM
VIN–
1
P1
M1
1
P1
M1
P3, M3
1
P1
M1
P9, M9
11
11 • VLIM – VREF – 9 • VTERM
1
P1
M1
P3||P9
14
14 • VLIM – VREF – 12 • VTERM
RT
M3||M9
RF
VCC
RG
VIN–
–
VOUT
RG
VIN+
(= VEXT)
+
RT
RT
VOUT = GAIN • (VIN+ – VIN–)
VEE GAIN = RF/RG
RF
VREF
VTERM
HIGH CM VOLTAGE DIFFERENCE AMPLIFIER
INPUT CM TO OP AMP IS ATTENUATED BY
RESISTORS RT CONNECTED TO VTERM.
7
12V
8 M9 50k
450k
4pF
9 M3 150k
10 M1 450k
MAX VEXT = 11 • (VCC – 1.2V) – VREF – 9 • VTERM
and:
2
VIN+
(RF + RG||RT) – VTERM • (RF||RG)/(RT + RF||RG))
= 11 • (10.8V) – 2.5 – 9 • 12 = 8.3V
Max, Min VEXT
(Substitute VCC – 1.2,
VEE + 1 for VLIM)
Gain
VEXT = (1 + RG/(RF||RT)) • (VINT – VREF • (RG||RT)/
Given the values of the resistors in the LT1991, this equation has been simplified and evaluated, and the resulting
equations provided in Table 6. As before, substituting VCC
– 1.2 and VEE + 1 for VLIM will give the valid upper and
lower common mode extremes respectively. Following
are sample calculations for the case shown in Figure 14,
right-hand side. Note that P9 and M9 are terminated so
row 3 of Table 6 provides the equation:
Noise
Gain
VIN+
VIN–
INPUT CM RANGE
= –60V TO 8.3V
1 P1
450k
2 P3
150k
3 P9
50k
–
6
VOUT
+
4pF
450k
REF 5
2.5V
LT1991
4
HIGH NEGATIVE CM VOLTAGE DIFFERENCE AMPLIFIER
IMPLEMENTED WITH LT1991.
RF = 450k, RG = 450k, RT 50k, GAIN = 1
VTERM = VCC = 12V, VREF = 2.5V, VEE = GROUND.
1991 F14
Figure 14. Extending CM Input Range
1991fg
21
LT1991
APPLICATIONS INFORMATION
3V
8
M9
9
M3
10
M1
VIN–
1
P1
2
P3
3
P9
VIN+
3V
7
VCC
6
VOUT
OUT
REF
5
1.25V
LT1991
VEE
VIN–
VIN+
4
8
M9
9
M3
10
M1
1
P1
2
P3
3
P9
VCM = 0.8V TO 2.35V
7
VCC
LT1991
VEE
VIN–
1
P1
2
P3
3
P9
VIN+
OUT
REF
5
6
VIN–
VOUT
6
VOUT
OUT
REF
5
1.25V
LT1991
VEE
VIN–
VIN+
4
1
P1
2
P3
3
P9
7
VCC
LT1991
VEE
VEE
4
3V
3V
7
VCC
6
VOUT
OUT
REF
5
1.25V
OUT
REF
5
6
VOUT
3V
VCM = –1V TO 0.6V
VDM <–40mV
VCM = 2V TO 3.6V
VDM > 40mV
8
M9
9
M3
10
M1
7
VCC
LT1991
1
P1
2
P3
3
P9
VIN+
4
3V
8
M9
9
M3
10
M1
3V
8
M9
9
M3
10
M1
3V
8
M9
9
M3
10
M1
VIN–
1
P1
2
P3
3
P9
VIN+
4
7
VCC
6
VOUT
OUT
REF
5
1.25V
LT1991
VEE
4
1.25V
VCM = 3.8V TO 7.75V
VCM = 0V TO 4V
3V
8
M9
9
M3
10
M1
VIN–
1
P1
2
P3
3
P9
VIN+
VEE
3V
3V
7
VCC
LT1991
VCM = –5V TO –1.25V
6
VOUT
OUT
REF
5
1.25V
VIN–
VIN+
4
8
M9
9
M3
10
M1
1
P1
2
P3
3
P9
7
VCC
LT1991
VEE
6
VOUT
OUT
REF
5
1.25V
VIN–
3V
8
M9
9
M3
10
M1
1
P1
2
P3
3
P9
VIN+
4
7
VCC
LT1991
VEE
6
VOUT
OUT
REF
5
1.25V
4
1.25V
VCM = –1.5V TO 7.2V
VCM = 9.8V TO 18.55V
3V
VIN–
VIN+
8
M9
9
M3
10
M1
1
P1
2
P3
3
P9
VEE
3V
3V
7
VCC
LT1991
VCM = –17.2V TO –8.45V
6
VOUT
OUT
REF
5
1.25V
4
VIN–
VIN+
8
M9
9
M3
10
M1
1
P1
2
P3
3
P9
7
VCC
LT1991
VEE
6
VOUT
OUT
REF
5
1.25V
4
VIN–
VIN+
3V
8
M9
9
M3
10
M1
1
P1
2
P3
3
P9
7
VCC
LT1991
VEE
6
VOUT
OUT
REF
5
1.25V
4
1.25V
VCM = –2.25V TO 8.95V
VCM = 12.75V TO 23.95V
VCM = –23.2V TO –12V
1991 F15
Figure 15. Common Mode Ranges for Various LT1991 Configurations on VS = 3V, 0V; with Gain = 1
1991fg
22
LT1991
APPLICATIONS INFORMATION
5V
8
M9
9
M3
10
M1
VIN–
1
P1
2
P3
3
P9
VIN+
5V
7
VCC
LT1991
OUT
REF
5
2.5V
VEE
6
VIN–
VOUT
VIN+
4
8
M9
9
M3
10
M1
1
P1
2
P3
3
P9
VCM = –0.5V TO 5.1V
7
VCC
LT1991
VEE
VIN–
1
P1
2
P3
3
P9
VIN+
OUT
REF
5
6
VIN–
VOUT
LT1991
OUT
REF
5
2.5V
VEE
6
VIN–
VOUT
VIN+
4
1
P1
2
P3
3
P9
7
VCC
LT1991
VEE
VEE
4
5V
5V
7
VCC
6
OUT
REF
5
VOUT
3V
VCM = –3V TO 2.6V
VDM <–40mV
VCM = 2V TO 7.6V
VDM > 40mV
8
M9
9
M3
10
M1
7
VCC
LT1991
1
P1
2
P3
3
P9
VIN+
4
5V
8
M9
9
M3
10
M1
5V
8
M9
9
M3
10
M1
OUT
REF
5
2.5V
6
VIN–
VOUT
5V
8
M9
9
M3
10
M1
1
P1
2
P3
3
P9
VIN+
4
7
VCC
LT1991
OUT
REF
5
2.5V
VEE
6
VOUT
4
2.5V
VCM = 2.5V TO 16.5V
VCM = –5V TO 9V
5V
8
M9
9
M3
10
M1
VIN–
1
P1
2
P3
3
P9
VIN+
VEE
5V
5V
7
VCC
LT1991
VCM = –12.5V TO 1.5V
OUT
REF
5
2.5V
6
VIN–
VOUT
VIN+
4
8
M9
9
M3
10
M1
1
P1
2
P3
3
P9
7
VCC
LT1991
VEE
OUT
REF
5
2.5V
6
VIN–
VOUT
5V
8
M9
9
M3
10
M1
1
P1
2
P3
3
P9
VIN+
4
7
VCC
LT1991
VEE
OUT
REF
5
2.5V
6
VOUT
4
2.5V
VCM = –14V TO 16.8V
VCM = 8.5V TO 39.3V
5V
VIN–
8
M9
9
M3
10
M1
1
P1
2
P3
3
P9
VIN+
VEE
5V
5V
7
VCC
LT1991
VCM = –36.5V TO –5.7V
OUT
REF
5
2.5V
4
6
VIN–
VOUT
VIN+
8
M9
9
M3
10
M1
1
P1
2
P3
3
P9
7
VCC
LT1991
VEE
OUT
REF
5
2.5V
4
6
VIN–
VOUT
VIN+
5V
8
M9
9
M3
10
M1
1
P1
2
P3
3
P9
7
VCC
LT1991
VEE
OUT
REF
5
2.5V
6
VOUT
4
2.5V
VCM = –18.5V TO 20.7V
VCM = 11.5V TO 50.7V
VCM = –48.5V TO –9.3V
1991 F16
Figure 16. Common Mode Ranges for Various LT1991 Configurations on VS = 5V, 0V; with Gain = 1
1991fg
23
LT1991
APPLICATIONS INFORMATION
5V
VIN–
VIN+
8
M9
9
M3
10
M1
5V
7
VCC
LT1991
1
P1
2
P3
3
P9
OUT
REF
5
VEE
6
VIN–
VOUT
8
M9
9
M3
10
M1
4
–5V
7
VCC
LT1991
1
P1
2
P3
3
P9
VIN+
VEE
4
5V
VIN–
1
P1
2
P3
3
P9
VIN+
2.5V
LT1991
OUT
REF
5
VEE
6
8
M9
9
M3
10
M1
VIN–
VOUT
4
VEE
1
P1
2
P3
3
P9
LT1991
VEE
OUT
REF
5
6
VOUT
1
P1
2
P3
3
P9
VIN+
4
–5V
–5V
1
P1
2
P3
3
P9
LT1991
VEE
1
P1
2
P3
3
P9
VIN+
VEE
OUT
REF
5
6
VIN–
VOUT
6
VIN–
VOUT
1
P1
2
P3
3
P9
VIN+
4
–5V
VCM = –56V TO 53.2V
–5V
OUT
REF
5
VEE
6
VOUT
4
5V
1
P1
2
P3
3
P9
4
7
VCC
LT1991
VEE
OUT
REF
5
6
VOUT
4
–5V
VCM = –60V TO –3.2V
5V
7
VCC
LT1991
VEE
LT1991
8
M9
9
M3
10
M1
VIN+
5V
OUT
REF
5
7
VCC
5V
VCM = 1V TO 60V
7
VCC
–5V
–5V
LT1991
8
M9
9
M3
10
M1
VOUT
VCM = –35V TO 4V
7
VCC
5V
VIN+
VOUT
–5V
VCM = –44V TO 41.8V
VIN–
6
VIN–
5V
VIN–
6
5V
–5V
8
M9
9
M3
10
M1
4
8
M9
9
M3
10
M1
VCM = –5V TO 34V
7
VCC
8
M9
9
M3
10
M1
OUT
REF
5
OUT
REF
5
VEE
5V
4
–5V
LT1991
1
P1
2
P3
3
P9
VIN+
7
VCC
–5V
VCM = –13V TO 2.6V
VDM <–40mV
7
VCC
5V
VIN+
VOUT
–5V
LT1991
1
P1
2
P3
3
P9
VIN+
VCM = –20V TO 19V
VIN–
6
5V
7
VCC
8
M9
9
M3
10
M1
OUT
REF
5
VIN–
–5V
VCM = –3V TO 12.6V
VDM > 40mV
VCM = –8V TO 7.6V
8
M9
9
M3
10
M1
5V
8
M9
9
M3
10
M1
OUT
REF
5
4
–5V
VCM = 4V TO 60V
6
VIN–
VOUT
VIN+
5V
8
M9
9
M3
10
M1
1
P1
2
P3
3
P9
7
VCC
LT1991
VEE
OUT
REF
5
6
VOUT
4
–5V
VCM = –60V TO –6.8V
1991 F17
Figure 17. Common Mode Ranges for Various LT1991 Configurations on VS = ±5V, with Gain = 1
1991fg
24
LT1991
TYPICAL APPLICATIONS
Micropower AV = 10 Instrumentation Amplifier
10
VM
9
8
7
6
VOUT
+
1/2 LT6011
–
4pF
–
VP
+
+
LT1991
1/2 LT6011
–
4pF
1
2
3
4
5
1991 TA02
1991fg
25
LT1991
PACKAGE DESCRIPTION
DD Package
10-Lead Plastic DFN (3mm × 3mm)
(Reference LTC DWG # 05-08-1699)
0.675 ±0.05
3.50 ±0.05
1.65 ±0.05
2.15 ±0.05 (2 SIDES)
PACKAGE
OUTLINE
0.25 ± 0.05
0.50
BSC
2.38 ±0.05
(2 SIDES)
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
R = 0.115
TYP
6
3.00 ±0.10
(4 SIDES)
0.38 ± 0.10
10
1.65 ± 0.10
(2 SIDES)
PIN 1
TOP MARK
(SEE NOTE 6)
(DD10) DFN 1103
5
0.200 REF
1
0.25 ± 0.05
0.50 BSC
0.75 ±0.05
0.00 – 0.05
2.38 ±0.10
(2 SIDES)
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-2).
CHECK THE LTC WEBSITE DATA SHEET FOR CURRENT STATUS OF VARIATION ASSIGNMENT
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE
TOP AND BOTTOM OF PACKAGE
1991fg
26
LT1991
PACKAGE DESCRIPTION
MS Package
10-Lead Plastic MSOP
(Reference LTC DWG # 05-08-1661)
0.889 ± 0.127
(.035 ± .005)
5.23
(.206)
MIN
3.20 – 3.45
(.126 – .136)
3.00 ± 0.102
(.118 ± .004)
(NOTE 3)
0.50
0.305 ± 0.038
(.0197)
(.0120 ± .0015)
BSC
TYP
RECOMMENDED SOLDER PAD LAYOUT
0.254
(.010)
10 9 8 7 6
3.00 ± 0.102
(.118 ± .004)
(NOTE 4)
4.90 ± 0.152
(.193 ± .006)
DETAIL “A”
0.497 ± 0.076
(.0196 ± .003)
REF
0° – 6° TYP
GAUGE PLANE
1 2 3 4 5
0.53 ± 0.152
(.021 ± .006)
DETAIL “A”
0.86
(.034)
REF
1.10
(.043)
MAX
0.18
(.007)
SEATING
PLANE
0.17 – 0.27
(.007 – .011)
TYP
0.50
(.0197)
BSC
0.127 ± 0.076
(.005 ± .003)
MSOP (MS) 0603
NOTE:
1. DIMENSIONS IN MILLIMETER/(INCH)
2. DRAWING NOT TO SCALE
3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
1991fg
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
27
LT1991
TYPICAL APPLICATION
Bidirectional Current Source
Single Supply AC Coupled Amplifier
VS+
8
M9
9
M3
10
M1
VIN–
VIN+
R2*
10k
1
P1
2
P3
3
P9
VS = 2.7V TO 36V
8
M9
9
M3
10
M1
7
1μF
6
LT1991
R1
10k
5
VCC
0.1μF
VIN
4
1
P1
2
P3
3
P9
V + – VIN–
ILOAD = IN
10kΩ
VS–
7
6
LT1991
VOUT
5
4
GAIN = 12
BW = 7Hz TO 32kHz
*SHORT R2 FOR LOWEST OUTPUT
OFFSET CURRENT. INCLUDE R2 FOR
HIGHEST OUTPUT IMPEDANCE.
1991 TA03
Ultra-Stable Precision Attenuator
Analog Level Adaptor
5V
8
M9
9
M3
10
M1
5V
8
M9
9
M3
10
M1
VIN
= 14V to 53V
1
P1
2
P3
3
P9
7
6
LT1991
VOUT = VIN
13
REF
5
1
P1
2
P3
3
P9
± 10VIN
4
LT1790 –2.5
5V
1μF
7
6
LT1991
0-4VOUT
REF
5
4
–5V
6
4
2
1991 TA04
1
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT1990
High Voltage, Gain Selectable Difference Amplifier
±250V Common Mode, Micropower, Pin Selectable Gain = 1, 10
LT1991
Precision Gain Selectable Difference Amplifier
Micropower, Pin Selectable Gain = –13 to 14
LT1995
High Speed, Gain Selectable Difference Amplifier
30MHz, 1000V/μs, Pin Selectable Gain = –7 to 8
LT6010/LT6011/LT6012 Single/Dual/Quad 135μA 14nV/√Hz Rail-to-Rail Out
Precision Op Amp
Similar Op Amp Performance as Used in LT1991 Difference Amplifier
LT6013/LT6014
Single/Dual 145μA 8nV/√Hz Rail-to-Rail Out
Precision Op Amp
Lower Noise A V ≥ 5 Version of LT1991 Type Op Amp
LTC6910-X
Programmable Gain Amplifiers
3 Gain Configurations, Rail-to-Rail Input and Output
1991fg
28
Linear Technology Corporation
LT 1007 REV G • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2006
Similar pages