LINER LTC1661I Micropower dual 10-bit dac in msop Datasheet

LTC1661
Micropower Dual
10-Bit DAC in MSOP
U
DESCRIPTIO
FEATURES
■
■
■
■
■
■
■
■
■
Tiny: Two 10-Bit DACs in an 8-Lead MSOP—
Half the Board Space of an SO-8
Micropower: 60µA per DAC
Sleep Mode: 1µA for Extended Battery Life
Rail-to-Rail Voltage Outputs Drive 1000pF
Wide 2.7V to 5.5V Supply Range
Double Buffered for Independent or Simultaneous
DAC Updates
Reference Range Includes Supply for Ratiometric
0V-to-VCC Output
Reference Input Has Constant Impedance over All
Codes (260kΩ Typ)—Eliminates External Buffers
3-Wire Serial Interface with
Schmitt Trigger Inputs
Differential Nonlinearity: ≤ ±0.75LSB Max
U
APPLICATIO S
■
■
■
■
■
Mobile Communications
Digitally Controlled Amplifiers and Attenuators
Portable Battery-Powered Instruments
Automatic Calibration for Manufacturing
Remote Industrial Devices
The LTC®1661 integrates two accurate, serially addressable, 10-bit digital-to-analog converters (DACs) in a
single tiny MS8 package. Each buffered DAC draws just
60µA total supply current, yet is capable of supplying DC
output currents in excess of 5mA and reliably driving
capacitive loads up to 1000pF. Sleep mode further reduces total supply current to a negligible 1µA.
Linear Technology’s proprietary, inherently monotonic
voltage interpolation architecture provides excellent linearity while allowing for an exceptionally small external
form factor. The double-buffered input logic provides
simultaneous update capability and can be used to write to
either DAC without interrupting Sleep mode.
Ultralow supply current, power-saving Sleep mode and
extremely compact size make the LTC1661 ideal for
battery-powered applications, while its straightforward
usability, high performance and wide supply range make
it an excellent choice as a general purpose converter.
For additional outputs and even greater board density,
please refer to the LTC1660 micropower octal DAC for
10-bit applications. For 8-bit applications, please consult
the LTC1665 micropower octal DAC.
, LTC and LT are registered trademarks of Linear Technology Corporation.
W
BLOCK DIAGRA
VOUT A
GND
VCC
VOUT B
8
7
6
5
Differential Nonlinearity (DNL)
0.75
LATCH
LATCH
10-BIT
DAC A
LATCH
LATCH
0.60
0.40
10-BIT
DAC B
LSB
0.20
0
–0.20
CONTROL
LOGIC
ADDRESS
DECODER
–0.40
–0.60
–0.75
0
SHIFT REGISTER
256
512
CODE
768
1023
1661 G02
1
2
3
4
CS/LD
SCK
DIN
REF
1661 BD
1
LTC1661
W W
W
AXI U
U
ABSOLUTE
RATI GS
(Note 1)
VCC to GND .............................................. – 0.3V to 7.5V
Logic Inputs to GND ................................ – 0.3V to 7.5V
VOUT A, VOUT B, REF to GND ............ – 0.3V to VCC + 0.3V
Maximum Junction Temperature ......................... 125°C
Storage Temperature Range ................ – 65°C to 150°C
Operating Temperature Range
LTC1661C ............................................. 0°C to 70°C
LTC1661I ........................................... – 40°C to 85°C
Lead Temperature (Soldering, 10 sec)................ 300°C
W
U
U
PACKAGE/ORDER I FOR ATIO
ORDER PART
NUMBER
TOP VIEW
CS/LD
SCK
DIN
REF
1
2
3
4
8
7
6
5
VOUT A
GND
VCC
VOUT B
CS/LD 1
8
VOUT A
SCK 2
7
GND
DIN 3
6
VCC
REF 4
5
VOUT B
LTC1661CMS8
LTC1661IMS8
MS8 PACKAGE
8-LEAD PLASTIC MSOP
MS8 PART MARKING
TJMAX = 125°C, θJA = 150°C/W
LTDV
LTDW
ORDER PART
NUMBER
TOP VIEW
LTC1661CN8
LTC1661IN8
N8 PACKAGE
8-LEAD PLASTIC DIP
TJMAX = 125°C, θJA = 100°C/W
Consult factory for Military grade parts.
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VCC = 2.7V to 5.5V, VREF ≤ VCC, VOUT Unloaded unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Accuracy
Resolution
Monotonicity
●
10
Bits
1V ≤ VREF ≤ VCC – 0.1V (Note 2)
●
10
Bits
DNL
Differential Nonlinearity
1V ≤ VREF ≤ VCC – 0.1V (Note 2)
●
±0.1
±0.75
LSB
INL
Integral Nonlinearity
1V ≤ VREF ≤ VCC – 0.1V (Note 2)
●
±0.4
±2
LSB
VOS
Offset Error
Measured at Code 20
●
±5
±30
mV
VCC = 5V, VREF = 4.096V
●
±15
VOS Temperature Coefficient
FSE
Full-Scale Error
±1
Full-Scale Error Temperature Coefficient
PSR
Power Supply Rejection
VREF = 2.5V
µV/°C
±12
LSB
±30
µV/°C
0.18
LSB/V
Reference Input
Input Voltage Range
Resistance
Active Mode
Reference Current
0
●
140
VCC
V
260
kΩ
●
15
pF
Sleep Mode
●
0.001
Capacitance
IREF
●
1
µA
5.5
V
195
154
3
µA
µA
µA
Power Supply
VCC
Positive Supply Voltage
For Specified Performance
●
ICC
Supply Current
VCC = 5V (Note 3)
VCC = 3V (Note 3)
Sleep Mode (Note 3)
●
●
●
2
2.7
120
95
1
LTC1661
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VCC = 2.7V to 5.5V, VREF ≤ VCC, VOUT Unloaded unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
DC Performance
Short-Circuit Current Low
VOUT = 0V, VCC = VREF = 5V, Code = 1023
●
10
25
100
mA
Short-Circuit Current High
VOUT = VCC = VREF = 5V, Code = 0
●
7
19
120
mA
AC Performance
Voltage Output Slew Rate
Rising (Notes 4, 5)
Falling (Notes 4, 5)
0.60
0.25
Voltage Output Settling Time
To ±0.5LSB (Notes 4, 5)
Capacitive Load Driving
V/µs
V/µs
30
µs
1000
pF
Digital I/O
VIH
Digital Input High Voltage
VCC = 2.7V to 5.5V
VCC = 2.7V to 3.6V
●
●
2.4
2.0
V
V
VIL
Digital Input Low Voltage
VCC = 4.5V to 5.5V
VCC = 2.7V to 5.5V
●
●
0.8
0.6
V
V
ILK
Digital Input Leakage
VIN = GND to VCC
●
±10
µA
CIN
Digital Input Capacitance
(Note 6)
●
10
pF
WU
TI I G CHARACTERISTICS
The ● denotes the specifications which apply over the full operating temperature
SYMBOL
CONDITIONS
range, otherwise specifications are at TA = 25°C.
PARAMETER
MIN
TYP
40
15
MAX
UNITS
VCC = 4.5V to 5.5V
t1
DIN Valid to SCK Setup
t2
DIN Valid to SCK Hold
●
0
– 10
ns
t3
SCK High Time
(Note 6)
●
30
14
ns
t4
SCK Low Time
(Note 6)
●
30
14
ns
t5
CS/LD Pulse Width
(Note 6)
●
80
27
ns
t6
LSB SCK High to CS/LD High
(Note 6)
●
30
2
ns
t7
CS/LD Low to SCK High
(Note 6)
●
20
– 21
ns
t9
SCK Low to CS/LD Low
(Note 6)
●
0
–5
ns
t11
CS/LD High to SCK Positive Edge
(Note 6)
●
20
0
SCK Frequency
Square Wave (Note 6)
●
●
ns
ns
16.7
MHz
VCC = 2.7V to 5.5V
t1
DIN Valid to SCK Setup
(Note 6)
●
t2
DIN Valid to SCK Hold
(Note 6)
t3
SCK High Time
(Note 6)
t4
SCK Low Time
(Note 6)
●
50
15
ns
t5
CS/LD Pulse Width
(Note 6)
●
100
30
ns
t6
LSB SCK High to CS/LD High
(Note 6)
●
50
3
ns
t7
CS/LD Low to SCK High
(Note 6)
●
30
– 14
ns
t9
SCK Low to CS/LD Low
(Note 6)
●
0
–5
ns
t11
CS/LD High to SCK Positive Edge
(Note 6)
●
30
0
SCK Frequency
Square Wave (Note 6)
●
Note 1: Absolute maximum ratings are those values beyond which the life
of a device may be impaired.
60
20
ns
●
0
– 10
ns
●
50
15
ns
ns
10
MHz
Note 2: Nonlinearity and monotonicity are defined from code 20 to code
1023 (full scale). See Applications Information.
3
LTC1661
WU
TI I G CHARACTERISTICS
Note 3: Digital inputs at 0V or VCC.
Note 4: Load is 10kΩ in parallel with 100pF.
Note 5: VCC = VREF = 5V. DAC switched between 0.1VFS and 0.9VFS,
i.e., codes k = 102 and k = 922.
Note 6: Guaranteed by design and not subject to test.
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Integral Nonlinearity (INL)
1400
0.75
2.0
0.60
1.5
VREF = 4.096V
∆VOUT < 1LSB
CODE = 1023
1200
0.40
1.0
VCC – VOUT (mV)
1000
0.20
LSB
0.5
LSB
Minimum Supply Headroom vs
Load Current (Output Sourcing)
Differential Nonlinearity (DNL)
0
0
–0.20
–0.5
125°C
800
25°C
600
–55°C
400
–1.0
–0.40
–1.5
–0.60
–2.0
200
0
–0.75
0
256
512
CODE
768
0
1023
256
512
CODE
768
1023
1400
3
2.9
125°C
600
–55°C
2.6
VCC = 5V
2.5
2.4
2
4
6
|IOUT| (mA) (Sinking)
8
10
1661 G04
4
–30
VCC = 3V
1.5
1.4
VCC = 2.7V
1.1
SOURCE
2
0
1.6
1.2
2.1
0
VCC = 3.6V
1.3
VCC = 4.5V
2.2
200
10
VREF = VCC
CODE = 512
1.7
2.3
400
8
1.8
VCC = 5.5V
VOUT (V)
VOUT (V)
VOUT (mV)
2
1.9
2.7
25°C
6
Midscale Output Voltage vs
Load Current
VREF = VCC
CODE = 512
2.8
1000
800
4
|IOUT| (mA) (Sourcing)
1661 G03
Midscale Output Voltage vs
Load Current
Minimum VOUT vs
Load Current (Output Sinking)
VCC = 5V
CODE = 0
2
1661 G02
1661 G01
1200
0
–20
–10
SINK
0
10
IOUT (mA)
SOURCE
1
20
30
1661 G05
–15 –12
–8
SINK
–4
0
4
IOUT (mA)
8
12 15
1661 G06
LTC1661
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Load Regulation vs
Output Current
Load Regulation vs
Output Current
2
2
VCC = VREF = 5V
CODE = 512
1.5
1.5
1
VCC = VREF = 3V
CODE = 512
VCC = VREF = 5V
10% TO
90% STEP
CODE = 922
4
1
0
–0.5
0.5
0
–0.5
–1
–1
–1.5
–1.5
SOURCE
–2
SINK
VOUT (V)
0.5
∆VOUT (LSB)
∆VOUT (LSB)
Large-Signal Step Response
5
3
2
1
SOURCE
–2
SINK
CODE = 102
0
–2
–1
0
IOUT (mA)
1
2
–500
0
IOUT (µA)
1661 G07
20
40
60
TIME (µs)
80
100
1661 G09
1661 G08
Supply Current vs
Logic Input Voltage
Supply Current vs Temperature
1.0
150
ALL DIGITAL INPUTS
SHORTED TOGETHER
140
0.8
VREF = VCC
CODE = 1023
130
SUPPLY CURRENT (µA)
SUPPLY CURRENT (mA)
0
500
0.6
0.4
0.2
120
110
VCC = 5.5V
100
VCC = 4.5V
90
VCC = 3.6V
80
70
VCC = 2.7V
60
0
0
1
2
3
4
LOGIC INPUT VOLTAGE (V)
50
–55 –35 –15
5
5 25 45 65 85 105 125
TEMPERATURE (°C)
1661 G10
1661 G11
WU
W
TI I G DIAGRA
t1
t2
t3
t6
t4
SCK
t9
t11
DIN
A3
t5
A2
A1
X1
X0
t7
CS/LD
1661 TD
5
LTC1661
U
U
U
PIN FUNCTIONS
CS/LD (Pin 1): Serial Interface Chip Select/Load Input.
When CS/LD is low, SCK is enabled for shifting data on DIN
into the register. When CS/LD is pulled high, SCK is
disabled and the operation(s) specified in the Control
code, A3-A0, is (are) performed. CMOS and TTL compatible.
SCK (Pin 2): Serial Interface Clock Input. CMOS and TTL
compatible.
DIN (Pin 3): Serial Interface Data Input. Input word data on
the DIN pin is shifted into the 16-bit register on the rising
edge of SCK. CMOS and TTL compatible.
REF (Pin 4): Reference Voltage Input. 0V ≤ VREF ≤ VCC.
VOUT A, VOUT B (Pins 8,5): DAC Analog Voltage Outputs.
The output range is
 1023 
0 ≤ VOUTA , VOUTB ≤ VREF 

 1024 
VCC (Pin 6): Supply Voltage Input. 2.7V ≤ VCC ≤ 5.5V.
GND (Pin 7): System Ground.
U
U
DEFINITIONS
Differential Nonlinearity (DNL): The difference between
the measured change and the ideal 1LSB change for any
two adjacent codes. The DNL error between any two codes
is calculated as follows:
DNL = (∆VOUT – LSB)/LSB
Where ∆VOUT is the measured voltage difference between
two adjacent codes.
INL = [VOUT – VOS – (VFS – VOS)(code/1023)]/LSB
Where VOUT is the output voltage of the DAC measured at
the given input code.
Least Significant Bit (LSB): The ideal voltage difference
between two successive codes.
LSB = VREF/1024
Full-Scale Error (FSE): The deviation of the actual fullscale voltage from ideal. FSE includes the effects of offset
and gain errors (see Applications Information).
Resolution (n): Defines the number of DAC output states
(2n) that divide the full-scale range. Resolution does not
imply linearity.
Integral Nonlinearity (INL): The deviation from a straight
line passing through the endpoints of the DAC transfer
curve (Endpoint INL). Because the output cannot go below
zero, the linearity is measured between full scale and the
lowest code which guarantees the output will be greater
than zero. The INL error at a given input code is calculated
as follows:
Voltage Offset Error (VOS): Nominally, the voltage at the
output when the DAC is loaded with all zeros. A single
supply DAC can have a true negative offset, but the output
cannot go below zero (see Applications Information).
6
For this reason, single supply DAC offset is measured at
the lowest code that guarantees the output will be greater
than zero.
LTC1661
U
OPERATIO
where k is the decimal equivalent of the binary DAC input
code D9-D0 and VREF is the voltage at REF (Pin 6).
By selecting the appropriate 4-bit Control code (see Table 2)
it is possible to perform single operations, such as loading
one DAC or changing Power-Down status (Sleep/Wake).
In addition, some Control codes perform two or more
operations at the same time. For example, one such code
loads DAC A, updates both outputs and Wakes the part up.
The DACs can be loaded separately or together, but the
outputs are always updated together.
Power-On Reset
Register Loading Sequence
The LTC1661 positively clears the outputs to zero scale
when power is first applied, making system initialization
consistent and repeatable.
See Figure 1. With CS/LD held low, data on the DIN input
is shifted into the 16-bit Shift Register on the positive edge
of SCK. The 4-bit Control code, A3-A0, is loaded first, then
the 10-bit Input code, D9-D0, ordered MSB-to-LSB in each
case. Two don’t-care bits, X1 and X0, are loaded last.
When the full 16-bit Input word has been shifted in, CS/LD
is pulled high, causing the system to respond according to
Table 2. The clock is disabled internally when CS/LD is
high. Note: SCK must be low when CS/LD is pulled low.
Transfer Function
The transfer function for the LTC1661 is:
 k 
VOUT(IDEAL) = 
 VREF
 1024 
Power Supply Sequencing
The voltage at REF (Pin 4) must not ever exceed the voltage
at VCC (Pin 6) by more than 0.3V. Particular care should be
taken in the power supply turn-on and turn-off sequences
to assure that this limit is observed. See Absolute Maximum Ratings.
Serial Interface
See Table 1. The 16-bit Input word consists of the 4-bit
Control code, the 10-bit Input code and two don’t-care bits.
Table 1. LTC1661 Input Word
Input Word
A3 A2 A1 A0 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 X1 X0
Control Code
Input Code
Don’t
Care
After the Input word is loaded into the register (see Figure 1),
it is internally converted from serial to parallel format. The
parallel 10-bit-wide Input code data path is then buffered
by two latch registers.
The first of these, the Input Register, is used for loading new
input codes. The second buffer, the DAC Register, is used
for updating the DAC outputs. Each DAC has its own 10-bit
Input Register and 10-bit DAC Register.
Sleep Mode
DAC control code 1110b is reserved for the special Sleep
instruction (see Table 2). In this mode, the digital parts of
the circuit stay active while the analog sections are disabled; static power consumption is greatly reduced. The
reference input and analog outputs are set in a high
impedance state and all DAC settings are retained in
memory so that when Sleep mode is exited, the outputs of
DACs not updated by the Wake command are restored to
their last active state.
Sleep mode is initiated by performing a load sequence
using control code 1110b (the DAC input code D9-D0 is
ignored).
To save instruction cycles, the DACs may be prepared with
new input codes during Sleep (control codes 0001b and
0010b); then, a single command (1000b) can be used both
to wake the part and to update the output values.
7
LTC1661
U
OPERATIO
Table 2. DAC Control Functions
CONTROL
A3 A2 A1 A0
INPUT REGISTER
STATUS
DAC REGISTER
STATUS
POWER-DOWN STATUS
(SLEEP/WAKE)
COMMENTS
0
0
0
0
No Change
No Update
No Change
No Operation. Power-Down Status Unchanged
(Part Stays In Wake or Sleep Mode)
0
0
0
1
Load DAC A
No Update
No Change
Load Input Register A with Data. DAC Outputs
Unchanged. Power-Down Status Unchanged
0
0
1
0
Load DAC B
No Update
No Change
Load Input Register B with Data. DAC Outputs
Unchanged. Power-Down Status Unchanged
0
0
1
1
Reserved
0
1
0
0
Reserved
0
1
0
1
Reserved
0
1
1
0
Reserved
0
1
1
1
1
0
0
0
No Change
Update Outputs
Wake
Load Both DAC Regs with Existing Contents of Input
Regs. Outputs Update. Part Wakes Up
1
0
0
1
Load DAC A
Update Outputs
Wake
Load Input Reg A. Load DAC Regs with New Contents
of Input Reg A and Existing Contents of Reg B. Outputs
Update. Part Wakes Up
1
0
1
0
Load DAC B
Update Outputs
Wake
Load Input Reg B. Load DAC Regs with Existing Contents
of Input Reg A and New Contents of Reg B. Outputs
Update. Part Wakes Up
1
0
1
1
1
1
0
0
1
1
0
1
No Change
No Update
Wake
Part Wakes Up. Input and DAC Regs Unchanged. DAC
Outputs Reflect Existing Contents of DAC Regs
1
1
1
0
No Change
No Update
Sleep
Part Goes to Sleep. Input and DAC Regs Unchanged. DAC
Outputs Set to High Impedance State
1
1
1
1
Load DACs A, B
with Same
10-Bit Code
Update Outputs
Wake
Load Both Input Regs. Load Both DAC Regs with New
Contents of Input Regs. Outputs Update. Part Wakes Up
SCK
DIN
Reserved
Reserved
Reserved
1
A3
2
A2
3
A1
CONTROL CODE
4
A0
5
D9
6
D8
7
D7
8
D6
9
D5
10
D4
11
D3
INPUT CODE
12
D2
13
D1
14
D0
15
X1
16
X0
DON’T CARE
INPUT WORD W0
CS/LD
(LTC1661
RESPONDS)
(SCK ENABLED)
Figure 1. Register Loading Sequence
8
1661 F01
LTC1661
U
OPERATIO
Voltage Outputs
Rail-to-Rail Output Considerations
Each of the rail-to-rail output amplifiers contained in the
LTC1661 can typically source or sink up to 5mA
(VCC = 5V). The outputs swing to within a few millivolts
of either supply when unloaded and have an equivalent
output resistance of 85Ω (typical) when driving a load to
the rails. The output amplifiers are stable driving capacitive loads up to 1000pF.
In any rail-to-rail DAC, the output swing is limited to
voltages within the supply range.
A small resistor placed in series with the output can be
used to achieve stability for any load capacitance. A 1µF
load can be successfully driven by inserting a 20Ω resistor
in series with the VOUT pin. A 2.2µF load needs only a 10Ω
resistor, and a 10µF electrolytic capacitor can be used
without any resistor (the equivalent series resistance of
the capacitor itself provides the required small resistance). In any of these cases, larger values of resistance,
capacitance or both may be substituted for the values
given.
If the DAC offset is negative, the output for the lowest
codes limits at 0V as shown in Figure 2b.
Similarly, limiting can occur near full scale when the REF
pin is tied to VCC. If VREF = VCC and the DAC full-scale error
(FSE) is positive, the output for the highest codes limits at
VCC as shown in Figure 2c. No full-scale limiting can occur
if VREF is less than VCC – FSE.
Offset and linearity are defined and tested over the region
of the DAC transfer function where no output limiting can
occur.
VREF = VCC
POSITIVE
FSE
OUTPUT
VOLTAGE
INPUT CODE
(c)
VREF = VCC
OUTPUT
VOLTAGE
0
512
INPUT CODE
(a)
1023
OUTPUT
VOLTAGE
0V
NEGATIVE
OFFSET
INPUT CODE
(b)
1661 F02
Figure 2. Effects of Rail-to-Rail Operation On a DAC Transfer Curve. (a) Overall Transfer Function (b) Effect of Negative
Offset for Codes Near Zero Scale (c) Effect of Positive Full-Scale Error for Input Codes Near Full Scale When VREF = VCC
9
LTC1661
U
TYPICAL APPLICATIO S
0.1µF
5V
4
6
8
DAC A
R2
50k
R1
5k
10V
0.1µF
VA1 = 2.5V
CS/LD
DIN
SCK
3
1
LTC1661
U1
3
FOR EACH U1 AND U2
CODE A CODE B ∆VH, ∆VL
512
1023
–250mV
512
512
0
512
0
250mV
VH = 7.5V
(FROM MAIN
INPUT DAC)
2
2
5
DAC B
8
+
U3A
LT1368
VH′ = VH + ∆VH
1
0.1µF
–
0.1µF
4
R3
50k
–5V
R4
5k
VB1
VH
0.1µF
5V
VL
4
6
VOUT
LOGIC
DRIVE
5
DAC B
R6
5k
R5
50k
7.5V ±250mV
–2.5V ±250mV
VB2
6
1
3
PIN
DRIVER
(1 0F N)
LTC1661
U2
5
2
8
DAC A
U3B
LT1368
VL′ = VL + ∆VL
7
+
0.1µF
R7
50k
VA2 = 2.5V
7
–
VA1 = VA2 = 2.5V
VH′ = VH + R1 (VA1 – VB1)
R2
R8
5k
VL′ = VL + R1 (VA2 – VB2)
R2
VL = –2.5V
(FROM MAIN
INPUT DAC)
FOR VALUES SHOWN,
∆VH, ∆VL ADJUSTMENT RANGE = ±250mV
∆VH, ∆VL STEP SIZE = 500µV
1661 F03
Figure 3. Pin Driver VH and VL Adjustment in ATE Applications
VIN ≥ 4.3V
0.1µF
0.1µF
6
2
LTC1258-4.1
4
4
1
4.096V
3
2
1
VCC
VOUTA
REF
8
0V TO 4.096V
(4mV/BIT)
5
T
0V TO 4.096V
(4mV/BIT)
DIN
LTC1661
SCK
CS/LD
VOUTB
GND
7
1661 F04
Figure 4. Using the LTC1258 and the LTC1661 In a Single Li-Ion Battery Application
10
LTC1661
U
PACKAGE DESCRIPTION
Dimensions in inches (millimeters) unless otherwise noted.
MS8 Package
8-Lead Plastic MSOP
(LTC DWG # 05-08-1660)
0.040 ± 0.006
(1.02 ± 0.15)
0.007
(0.18)
0.118 ± 0.004*
(3.00 ± 0.102)
0.034 ± 0.004
(0.86 ± 0.102)
8
7 6
5
0° – 6° TYP
SEATING
PLANE 0.012
(0.30)
0.0256
REF
(0.65)
BSC
0.021 ± 0.006
(0.53 ± 0.015)
0.118 ± 0.004**
(3.00 ± 0.102)
0.193 ± 0.006
(4.90 ± 0.15)
0.006 ± 0.004
(0.15 ± 0.102)
MSOP (MS8) 1098
1
* DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH,
PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
** DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
2 3
4
N8 Package
8-Lead PDIP (Narrow 0.300)
(LTC DWG # 05-08-1510)
0.400*
(10.160)
MAX
8
7
6
5
1
2
3
4
0.255 ± 0.015*
(6.477 ± 0.381)
0.300 – 0.325
(7.620 – 8.255)
0.009 – 0.015
(0.229 – 0.381)
(
+0.035
0.325 –0.015
8.255
+0.889
–0.381
)
0.045 – 0.065
(1.143 – 1.651)
0.130 ± 0.005
(3.302 ± 0.127)
0.065
(1.651)
TYP
0.100
(2.54)
BSC
0.125
(3.175) 0.020
MIN
(0.508)
MIN
0.018 ± 0.003
(0.457 ± 0.076)
N8 1098
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm)
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
11
LTC1661
U
TYPICAL APPLICATIO
5V
4
0.1µF
6
8
DAC A
R2
50k
R1
5k
10V
0.1µF
VA1 = 2.5V
CS/LD
DIN
SCK
3
1
LTC1661
U1
3
FOR EACH U1 AND U2
CODE A CODE B ∆VH, ∆VL
512
1023
–250mV
512
512
0
512
0
250mV
VH = 7.5V
(FROM MAIN
INPUT DAC)
2
2
5
DAC B
8
+
U3A
LT1368
1
VH′ = VH + ∆VH
0.1µF
–
0.1µF
4
R3
50k
–5V
R4
5k
VB1
VH
5V
0.1µF
VL
4
6
VOUT
LOGIC
DRIVE
DAC B
5
R6
5k
R5
50k
7.5V ±250mV
–2.5V ±250mV
VB2
6
1
3
PIN
DRIVER
(1 0F N)
LTC1661
U2
5
2
DAC A
8
U3B
LT1368
7
VL′ = VL + ∆VL
+
R7
50k
VA2 = 2.5V
7
–
0.1µF
VA1 = VA2 = 2.5V
R8
5k
VL = –2.5V
(FROM MAIN
INPUT DAC)
VH′ = VH + R1 (VA1 – VB1)
R2
VL′ = VL + R1 (VA2 – VB2)
R2
FOR VALUES SHOWN,
∆VH, ∆VL ADJUSTMENT RANGE = ±250mV
∆VH, ∆VL STEP SIZE = 500µV
1661 F03
Pin Driver VH and VL Adjustment in ATE Applications
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LTC1446/LTC1446L
Dual 12-Bit VOUT DACs in SO-8 Package with Internal Reference
LTC1446: VCC = 4.5V to 5.5V, VOUT = 0V to 4.095V
LTC1446L: VCC = 2.7V to 5.5V, VOUT = 0V to 2.5V
LTC1448
Dual 12-Bit VOUT DAC in SO-8 Package
VCC = 2.7V to 5.5V, External Reference Can Be Tied to VCC
LTC1454/LTC1454L
Dual 12-Bit VOUT DACs in SO-16 Package with Added Functionality
LTC1454: VCC = 4.5V to 5.5V, VOUT = 0V to 4.095V
LTC1454L: VCC = 2.7V to 5.5V, VOUT = 0V to 2.5V
LTC1458/LTC1458L
Quad 12-Bit Rail-to-Rail Output DACs with Added Functionality
LTC1458: VCC = 4.5V to 5.5V, VOUT = 0V to 4.095V
LTC1458L: VCC = 2.7V to 5.5V, VOUT = 0V to 2.5V
LTC1659
Single Rail-to-Rail 12-Bit VOUT DAC in 8-Lead MSOP Package
VCC: 2.7V to 5.5V
Low Power Multiplying VOUT DAC. Output Swings from
GND to REF. REF Input Can Be Tied to VCC
LTC1663
Single 10-Bit VOUT DAC in SOT-23 Package
VCC = 2.7V to 5.5V, Internal Reference, 60µA
LTC1665/LTC1660
Octal 8/10-Bit VOUT DAC in 16-Pin Narrow SSOP
VCC = 2.7V to 5.5V, Micropower, Rail-to-Rail Output
12
Linear Technology Corporation
1661f LT/TP 0100 4K • PRINTED IN THE USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408)432-1900 ● FAX: (408) 434-0507 ● www.linear-tech.com
 LINEAR TECHNOLOGY CORPORATION 1999
Similar pages