LITEON LTL2P3SEK-0D2A Property of lite-on only Datasheet

LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Technical Data
Ultra Bright LED Lamp for Traffic Sign
LTL2P3SEK-0D2A
Red
(22o)
LTL2R3SEK-0D2A
Red
(30o)
LTL2P3SYK-0D2A
Amber (22o)
LTL2R3SYK-0D2A
Amber (30o)
Benefits
* Lower system cost.
Description
* Higher luminous efficiency than incandescent lamp.
The source color light emitting diode dice of these devices is
* Fewer LED are required due to the TS AlInGaP
made of AlInGaP on a transparent substrate (TS).
The water clear epoxy lens on these devices create viewing
technology.
angles of 22 and 30 degrees that match international
Features
specifications for traffic sign utilization.
* High luminous intensity output.
These LED lamps provide superior endurance against
* Low power consumption.
moisture and high temperatures thus are reliable for outdoor
* High efficiency.
environment use. With a lower power consumption than
* Versatile mounting on PCB or panel.
traditional incandescent lamps, these devices yield lower
* I.C. Compatible / low current requirements.
system cost.
3
* Popular T-1
4
diameter (5 mm).
Applications
* Traffic signals.
* Versatile warning signals.
* Outdoor traffic display panels.
Part No. : LTL2P3SEK-0D2A \ LTL2R3SEK-0D2A
LTL2P3SEK-0D2A \ LTL2R3SEK-0D2A
BNS-OD-C131/A4
Page :
1
of
12
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Features
* High luminous intensity output.
* Low power consumption.
* High efficiency.
* Versatile mounting on PCB or panel.
* I.C. Compatible / low current requirements.
* Popular T-1 3/4 diameter.
Package Dimensions
Part No.
Lens
Source Color
LTL2P3SEK-0D2A / LTL2R3SEK-0D2A
Water Clear
TS AlInGaP Red
LTL2P3SYK-0D2A / LTL2R3SYK-0D2A
Water Clear
TS AlInGaP Amber
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25mm (.010") unless otherwise noted.
3. Protruded resin under flange is 1.0mm (.04") max.
4. Lead spacing is measured where the leads emerge from the package.
5. Specifications are subject to change without notice.
Part No. : LTL2P3SEK-0D2A \ LTL2R3SEK-0D2A
LTL2P3SYK-0D2A \ LTL2R3SYK-0D2A
BNS-OD-C131/A4
Page :
2
of
12
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Absolute Maximum Ratings at TA=25 °C
Parameter
Maximum Rating
Unit
130
mW
100
mA
Continuous Forward Current
50
mA
Derating Linear From 50 °C
0.6
mA/℃
5
V
Power Dissipation
Peak Forward Current
(1/10 Duty Cycle, 0.1ms Pulse Width)
Reverse Voltage
Operating Temperature Range
-40°C to + 80°C
Storage Temperature Range
-55°C to + 100°C
Lead Soldering Temperature
[1.6mm(.063") From Body]
260°C for 5 Seconds
Part No. : LTL2P3SEK-0D2A \ LTL2R3SEK-0D2A
LTL2P3SYK-0D2A \ LTL2R3SYK-0D2A
BNS-OD-C131/A4
Page :
3
of
12
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Electrical / Optical Characteristics at TA=25 °C
Parameter
Luminous Intensity
Viewing Angle
Peak Emission
Wavelength
Dominant Wavelength
Spectral Line
Half-Width
Symbol
IV
2θ1/2
λP
λd
∆λ
Forward Voltage
VF
Reverse Current
IR
Capacitance
C
Part NO.
Min.
Typ.
2P3SEK
2500
4800
2R3SEK
1900
3700
2P3SYK
1900
3700
2R3SYK
1900
2800
(LTL)
Max.
mcd
2P3SXK
22
2R3SXK
30
Red
639
Amber
591
Red
630
Amber
590
Red
17
Amber
17
Red
2.25
2.7
Amber
2.35
2.7
deg
nm
nm
Test Condition
IF = 20mA
Note 1
Note 2 (Fig.5)
Measurement
@Peak (Fig.1)
Note 4
nm
100
40
Unit
V
IF = 20mA
µA
VR = 5V
pF
VF = 0 , f = 1MHz
NOTE:
1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE
eye-response curve.
2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity.
3. Iv classification code is marked on each packing bag.
4. The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the single
wavelength which defines the color of the device.
Part No. : LTL2P3SEK-0D2A \ LTL2R3SEK-0D2A
LTL2P3SYK-0D2A \ LTL2R3SYK-0D2A
BNS-OD-C131/A4
Page :
4
of
12
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Typical Electrical / Optical Characteristics Curves
(25 °C Ambient Temperature Unless Otherwise Noted)
Part No. : LTL2P3SEK-0D2A \ LTL2R3SEK-0D2A
LTL2P3SYK-0D2A \ LTL2R3SYK-0D2A
BNS-OD-C131/A4
Page :
5
of
12
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Features
* Compatible with radial lead automatic insertion equipment.
* Most radial lead plastic lead lamps available packaged in tape and folding.
* 2.54mm (0.1") straight lead spacing available.
* Folding packaging simplifies handling and testing.
Reel packaging is available by removing suffix “A” on option.
Package Dimensions
Item
Tape Feed Hole Diameter
Component Lead Pitch
Front to Rear Deflection
Feed Hole to Bottom of Component
Feed Hole to Overall Component Height
Lead Length After Component Height
Feed Hole Pitch
Lead Location
Center of Component Location
Total Tape Thickness
Feed Hole Location
Adhesive Tape Width
Adhesive Tape Position
Tape Width
Symbol
D
F
△H
H1
H2
L
P
P1
P2
T
W0
W1
W2
W3
Specification
Minimum
Maximum
mm
inch
mm
inch
3.8
0.149
4.2
0.165
2.3
0.091
3.0
0.118
--2.0
0.078
19.5
0.768
21.5
0.847
27.9
1.098
30.5
1.201
W0
12.4
0.488
4.4
0.173
5.05
0.198
--8.5
0.334
14.5
0.571
0
0
17.5
0.689
11.0
13.0
5.8
7.65
0.90
9.75
15.5
3.0
19.0
0.433
0.511
0.228
0.301
0.035
0.384
0.610
0.118
0.748
Part No. : LTL2P3SEK-0D2A \ LTL2R3SEK-0D2A
LTL2P3SYK-0D2A \ LTL2R3SYK-0D2A
BNS-OD-C131/A4
Page :
6
of
12
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Packing Spec
2000 pcs per inner carton
10 Inner cartons per outer carton
total 20000 pcs per outer carton
In every shipping lot, only the last pack will be non-full packing
Part No. : LTL2P3SEK-0D2A \ LTL2R3SEK-0D2A
LTL2P3SYK-0D2A \ LTL2R3SYK-0D2A
BNS-OD-C131/A4
Page :
7
of
12
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Bin Code List For Reference
Luminous Intensity Iv(mcd)
Bin Code
S
T
U
V
W
X
Min.
1900
2500
3200
4200
5500
7200
IF@20mA
Max.
2500
3200
4200
5500
7200
9300
Note: Tolerance of each bin limit is ±15%
Dominant Wavelength λd(nm)
IF@20mA
Bin Code
Min.
Max.
A
584.5
587.0
B
587.0
589.5
C
589.5
592.0
D
592.0
594.5
E
594.5
597.0
Note: Tolerance of each bin limit is ±1nm
Forward Voltage Vf (Volts)
IF@20mA
Bin Code
Min.
Max.
1
1.8
1.9
2
1.9
2.0
3
2.0
2.1
4
2.1
2.2
5
2.2
2.3
6
2.3
2.4
7
2.4
2.5
8
2.5
2.6
9
2.6
2.7
Part No. : LTL2P3SEK-0D2A \ LTL2R3SEK-0D2A
LTL2P3SYK-0D2A \ LTL2R3SYK-0D2A
BNS-OD-C131/A4
Page :
8
of
12
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
CAUTIONS
1. Application
The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment,
communication equipment and household applications).Consult Liteon’s Sales in advance for information on
applications in which exceptional reliability is required, particularly when the failure or malfunction of the
LEDs may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment,
medical and life support systems and safety devices).
2. Storage
The storage ambient for the LEDs should not exceed 30°C temperature or 70% relative humidity.
It is recommended that LEDs out of their original packaging are used within three months.
For extended storage out of their original packaging, it is recommended that the LEDs be stored in
a sealed container with appropriate desiccant or in desiccators with nitrogen ambient.
3. Cleaning
Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LEDs if necessary.
4. Lead Forming & Assembly
During lead forming, the leads should be bent at a point at least 3mm from the base of LED lens.
Do not use the base of the lead frame as a fulcrum during forming.
Lead forming must be done before soldering, at normal temperature.
During assembly on PCB, use minimum clinch force possible to avoid excessive mechanical stress.
5. Soldering
When soldering, leave a minimum of 2mm clearance from the base of the lens to the soldering point.
Dipping the lens into the solder must be avoided.
Do not apply any external stress to the lead frame during soldering while the LED is at high temperature.
Recommended soldering conditions :
Soldering iron
Temperature
Soldering time
300°C Max.
3 sec. Max.
(one time only)
Wave soldering
Pre-heat
Pre-heat time
Solder wave
Soldering time
100°C Max.
60 sec. Max.
260°C Max.
10 sec. Max.
Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or
catastrophic failure of the LED
Part No. : LTL2P3SEK-0D2A \ LTL2R3SEK-0D2A
LTL2P3SYK-0D2A \ LTL2R3SYK-0D2A
BNS-OD-C131/A4
Page :
9
of
12
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
6. Drive Method
An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs
connected in parallel in an application, it is recommended that a current limiting resistor be
incorporated in the drive circuit, in series with each LED as shown in Circuit A below.
Circuit model A
Circuit model B
LED
LED
(A) Recommended circuit
(B) The brightness of each LED might appear different due to the differences in the I-V characteristics
of those LEDs
7. ESD (Electrostatic Discharge)
Static Electricity or power surge will damage the LED.
Suggestions to prevent ESD damage:
„ Use a conductive wrist band or anti- electrostatic glove when handling these LEDs
„ All devices, equipment, and machinery must be properly grounded
„ Work tables, storage racks, etc. should be properly grounded
„ Use ion blower to neutralize the static charge which might have built up on surface of the LEDs
plastic lens as a result of friction between LEDs during storage and handing
Part No. : LTL2P3SEK-0D2A \ LTL2R3SEK-0D2A
LTL2P3SYK-0D2A \ LTL2R3SYK-0D2A
BNS-OD-C131/A4
Page :
10
of
12
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Suggested checking list :
Training and Certification
1. Everyone working in a static-safe area is ESD-certified?
2. Training records kept and re-certification dates monitored?
Static-Safe Workstation & Work Areas
1. Static-safe workstation or work-areas have ESD signs?
2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V?
3. All ionizer activated, positioned towards the units?
4. Each work surface mats grounding is good?
Personnel Grounding
1. Every person (including visitors) handling ESD sensitive (ESDS) items wear wrist strap, heel strap or
conductive shoes with conductive flooring?
2. If conductive footwear used, conductive flooring also present where operator stand or walk?
3. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V*?
4. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DSL?
5. All wrist strap or heel strap checkers calibration up to date?
Note: *50V for Blue LED.
Device Handling
1. Every ESDS items identified by EIA-471 labels on item or packaging?
2. All ESDS items completely inside properly closed static-shielding containers when not at static-safe
workstation?
3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items?
4. All flexible conductive and dissipative package materials inspected before reuse or recycle?
Others
1. Audit result reported to entity ESD control coordinator?
2. Corrective action from previous audits completed?
3. Are audit records complete and on file?
Part No. : LTL2P3SEK-0D2A \ LTL2R3SEK-0D2A
LTL2P3SYK-0D2A \ LTL2R3SYK-0D2A
BNS-OD-C131/A4
Page :
11
of
12
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
8. Reliability Test
Classification
Test Item
Operation Life
High Temperature
High Humidity
Storage
Endurance
Test
Environmental
Test
High Temperature
High Humidity
Reverse BIAS
Test Condition
Reference Standard
Ta= Under Room Temperature As
Per Data Sheet Maximum Rating
*Test Time= 1000HRS (-24HRS,+72HRS)
MIL-STD-750D:1026 (1995)
MIL-STD-883D:1005 (1991)
JIS C 7021:B-1 (1982)
Ta= 65±5℃
RH= 90 〜 95%
MIL-STD-202F: 103B(1980)
JIS C 7021 : B-11(1982)
Test Time= 240HRS±2HRS
Ta= 65±5℃
RH= 90 〜 95%
VR=5V
Test Time = 500HRS (-24HRS, +48HRS)
JIS C 7021 : B-11(1982)
High Temperature
Storage
Ta= 105±5℃
*Test Time= 1000HRS (-24HRS,+72HRS)
MIL-STD-883D:1008 (1991)
JIS C 7021:B-10 (1982)
Low Temperature
Storage
Ta= -55±5℃
*Test Time=1000HRS (-24HRS,+72HRS)
JIS C 7021:B-12 (1982)
Temperature
Cycling
105℃ 〜 25℃ 〜 -55℃ 〜 25℃
30mins 5mins
30mins 5mins
10 Cycles
MIL-STD-202F:107D (1980)
MIL-STD-750D:1051(1995)
MIL-STD-883D:1010 (1991)
JIS C 7021: A-4(1982)
Thermal
Shock
105 ± 5℃ 〜 -55℃ ± 5℃
10mins
10mins
10 Cycles
MIL-STD-202F:107D(1980)
MIL-STD-750D:1051(1995)
MIL-STD-883D:1011 (1991)
Solder
Resistance
T.sol = 260 ± 5℃
Dwell Time= 10 ± 1secs
MIL-STD-202F:210A(1980)
MIL-STD-750D:2031(1995)
JIS C 7021: A-1(1982)
T. sol = 230 ± 5℃
Dwell Time= 5 ± 1secs
MIL-STD-202F:208D(1980)
MIL-STD-750D:2026(1995)
MIL-STD-883D:2003(1991)
JIS C 7021: A-2(1982)
Solderability
9. Others
The appearance and specifications of the product may be modified for improvement, without prior notice.
Part No. : LTL2P3SEK-0D2A \ LTL2R3SEK-0D2A
LTL2P3SYK-0D2A \ LTL2R3SYK-0D2A
BNS-OD-C131/A4
Page :
12
of
12
Similar pages