Sanyo LV56351HA 1ch dc/dc boost converter Datasheet

Ordering number : ENA2145
Bi-CMOS IC
LV56351HA
1ch DC/DC boost converter
Overview
LV56351HA integrates 1ch DC/DC boost converter and 1ch LDO. It is suitable as the power supply for BS/CS
antennas of LCD/PDP TV and BD recorders that require automatic recovery without IC destruction and malfunction
when the output is short-circuited.
Functions
[DC/DC boost converter]
• Soft-start time: 2.8ms
• Frequency 425kHz operation
• Pulse by pulse over current limiter
• Short circuit protector (SCP)
[LDO]
• Over current limiter (Fold back)
[All]
• Under voltage lockout
• Thermal shutdown protector
• Power good
Specifications
Maximum Ratings at Ta = 25°C
Parameter
Symbol
Conditions
Ratings
Unit
VCC maximum supply voltage
VCC max
-0.3 to 25
V
LDOIN maximum input voltage
VLDOIN max
-0.3 to 30
V
SW maximum voltage
VSW max
-0.3 to 30
V
Allowable power dissipation
Pd max
1.45
W
Operating temperature
Topr
-30 to +85
°C
Operating junction temperature
Tjopr
-30 to +125
°C
Storage temperature
Tstg
-40 to +150
°C
VCC, EN
25
V
pin
SW, LDOIN, LDOOUT
30
V
voltage
IN1, IN2, FB, SCP, PGOOD, DDCTL
6
V
Allowable
*1
*1 Mounted on a specified board : 32mm × 38mm × 1.6mm, glass epoxy, double side board.
Caution 1) Absolute maximum ratings represent the value which cannot be exceeded for any length of time.
Caution 2) Even when the device is used within the range of absolute maximum ratings, as a result of continuous usage under high temperature, high current,
high voltage, or drastic temperature change, the reliability of the IC may be degraded. Please contact us for the further details.
Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to
"standard application", intended for the use as general electronics equipment. The products mentioned herein
shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life,
aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system,
safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives
in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any
guarantee thereof. If you should intend to use our products for new introduction or other application different
from current conditions on the usage of automotive device, communication device, office equipment, industrial
equipment etc. , please consult with us about usage condition (temperature, operation time etc.) prior to the
intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely
responsible for the use.
Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate
the performance, characteristics, and functions of the described products in the independent state, and are not
guarantees of the performance, characteristics, and functions of the described products as mounted in the
customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent
device, the customer should always evaluate and test devices mounted in the customer ' s products or
equipment.
O3112NKPC 20121009-S00001 No.A2145-1/9
LV56351HA
Recommended Operating Conditions at Ta = 25°C
Parameter
Symbol
Conditions
Ratings
Unit
VCC supply voltage
VCC
8 to 23
V
LDOIN input voltage
VLDOIN
8 to 28
V
SW voltage
VSW
-0.3 to 28
V
EN voltage
VEN
0 to 23
V
Electrical Characteristics at Ta = 25°C, VCC = 12V, VEN=2V, LDOIN=16V, LDOOUT=15V
Parameter
Symbol
Conditions
Ratings
min
typ
Unit
max
All
Supply current1
ICC
Switching is turned off
Supply current2
IOFF
EN = 0V
Reference voltage
VREF
Enable voltage
VEN
Disable voltage
VDIS
1.8
1.2348
1.26
3.5
mA
10
μA
1.2852
V
2.0
EN input current
IEN
VEN = 2.0V
PGOOD threshold
VPG
IN1 ≥ VREF×85% and IN2 ≥ VREF×85%
PGOOD sink current
IPG
VPGOOD = 0.5V
PGOOD leak current
IPGLK
VPGOOD = 2V
UVLO on voltage
VUVLO
Thermal shutdown temperature
TTSD
*2
TSD hysteresis
THYS
*2
FB output voltage ”Low”
FBLow
IN1 = 2.0V, IFB = -20μA (Sink)
FB output voltage “High”
FBHigh
IN1 = 0.2V, IFB = 20μA (Source)
Soft-start time
TSS
Oscillator frequency
FOSC
Max on duty
DMAX
V
0.4
V
10
μA
VREF×0.85
V
1.0
mA
10
7.0
μA
V
°C
130
°C
30
DC/DC boost converter
SW on resistance
RON
SW peak current
IPK
SCP source current
ISCP
0.2
1.8
V
V
2.8
ms
425
kHz
78
85
92
%
1.5
1.8
A
4.8
μA
VREF
V
Ω
0.7
SCP threshold
VSCP
DDCTL on voltage
VDDCTLON
DC/DC Off
DDCTL off voltage
VDDCTLOFF
DC/DC On
0.4
V
DDCTL input current
IDDCTL
VDDCTL = 2V
20
μA
670
mA
2.0
V
LDO
Maximum output current
IOMAX
350
520
Line regulation
RLN
16V < LDOIN < 21V
20
mV
Load regulation
RLD
10mA < IO < 300mA
20
mV
Dropout voltage
VDROP
IO = 300mA
0.4
V
Short current
ISHORT
LDOOUT = GND
100
mA
0.25
*2: Design guarantee value.
No.A2145-2/9
LV56351HA
Package Dimensions
unit : mm (typ)
3313A
Allowable power dissipation, Pd max -- W
2.0
6.5
0.5
6.4
4.4
14
1 2
0.15
0.22
1.3
0.65
1.5 MAX
(2.28)
Pd max -- Ta
Mounted on the specified board: 32×38×1.6mm3
glass epoxy, double side board.
1.5
1.45
1.0
0.58
0.5
0
--30
0
0.1 (1.3)
1.5
30
60
90
120
Ambient temperature, Ta -- °C
SANYO : HSSOP14(225mil)
Specified board (32mm × 38mm × 1.6mm, glass epoxy, double side board)
SCP
PGOOD
V1
R1 R3
R7
L1
C4
DDCTL
C6 R6 R2 R4
C5
R5 C7
LDOIN
EN
C1
C2
C3
D1
VCC
LDOOUT
GND
〈〈front〉〉
〈〈back〉〉
Pin assignment
Fin
1
PGND
LDOOUT
PGND
Fin
SW
14
NC
13
12
IN2
VCC
EN
IN1
DDCTL
10
2
LDOIN
3
NC
4
5
6
FB
7
SGND
11
SCP
9
PGOOD
8
Top view
No.A2145-3/9
LV56351HA
Pin function
Pin No.
Pin name
Function
1
LDOOUT
LDO output
2
LDOIN
LDO input
7
SGND
Signal ground (*3)
Equivalent circuit
2 LDOIN
1 LDOOUT
7 SGND
4
IN2
LDO feedback input
10kΩ
IN2 4
SGND 7
5
IN1
DC/DC error amplifier input
10kΩ
IN1 5
SGND 7
6
FB
DC/DC error amplifier output
1kΩ
FB 6
SGND 7
8
PGOOD
Power good output
8 PGOOD
500Ω
7 SGND
9
SCP
DC/DC SCP capacitor connect pin for timer setting
300Ω 2kΩ
9 SCP
7 SGND
SGND 7
EN
Enable
12
VCC
Power supply
VCC 12
EN 11
SGND 7
210kΩ
11
VREG
DDCTL 10
110kΩ
DC/DC on and off control
210kΩ
DDCTL
410kΩ
10
*3: When you use this IC, Please short-circuit all the pins of SGND and PGND on the IC mounting side.
Continued on next page.
No.A2145-4/9
LV56351HA
Continued from preceding page.
Pin No.
Pin name
Function
14
SW
DC/DC open drain output
Fin
PGND
Power ground (*3)
Equivalent circuit
VREG
14 SW
Fin PGND
*3: When you use this IC, Please short-circuit all the pins of SGND and PGND on the IC mounting side.
Function overview
(1) UVLO (Under Voltage Lockout)
UVLO stops outputs of both DC/DC and LDO to prevent malfunction when VCC decreases. UVLO operates when
VCC falls below the UVLO voltage. This function is a non-latch-type, and recovers these outputs automatically when
VCC exceeds the UVLO voltage.
(2) Power good
Power good notifies that the output voltages of DC/DC and LDO are within the range of the setting voltage. The two
output voltages are monitored through the voltage of IN1 and IN2. The output is judged to be “power good” when both
outputs are 85% or higher compared to the setting voltages. If either IN1 or IN2 voltage falls below VREF×85%,
PGOOD output becomes L → H (No Good). When IN1 and IN2 voltages become (VREF×85%) + 30mV or higher,
PGOOD output becomes H → L (Good). During soft start, the output is H (No Good).
〈〈Power good circuit diagram〉〉
Power supply (6V or less)
P. Good
Comp.
IN1
IN2
PGOOD
_Pin
10kΩ (Example)
Good ⇒ L output
No Good ⇒ H output
+
+
-
VREF × 85%
(Hysteresis=30mV)
(3) Pulse-by-Pulse over current protection (P by P)
The P by P stops switch-on operation of a certain cycle by force when the current of power MOSFET reaches the
maximum output peak current.
〈〈P by P circuit diagram〉〉
Error
Amp.
PWM
Comp.
Logic
Triangular wave
P by P
Comp.
SW_pin
Power
The current of power_Tr is
constantly monitored.
If the peak current > 1.8A,
switching_on operation during the
cycle stops compulsorily
No.A2145-5/9
LV56351HA
(4) Short Circuit Protector (SCP)
When output voltage of DC/DC decreases due to short-circuit; for example, SCP latches off the outputs of DC/DC and
LDO by timer.
When output voltage of DC/DC decreases and FB turns to H, which is the error amplifier output, charge at 4.8μA
constant current starts to SCP capacitor for timer setting. When SCP voltage exceeds the threshold voltage (=VREF),
latch-off occurs. If the output voltage recovers until the time the SCP voltage reaches to the threshold voltage, SCP
capacitor is discharged and timer is reset. To restart the output after latch-off, you need to input EN signal again. If you
do not use the SCP function, make sure to short SCP and GND.
To define timer, you need to calculate a value of SCP capacitor using the following formula because timer (tSCP)
depends on capacitance.
CSCP = (ISCP × tSCP)/VREF
〈〈SCP circuit diagram〉〉
〈〈Waveform of SCP_Pin〉〉
ISCP=4.8μA
SCP_Pin
DC/DC OFF (≈VCC)
DC/DC
Output
SCP
Comp.
Logic
CSCP
for timer
setting
VREF
tSCP
Threshhold voltage (VREF)
SCP
Voltage
Time
Discharge Tr
Reset
Latch-OFF
(5) DC/DC on and off control
This function controls on and off of DC/DC during the operation of IC.
〈〈Turning on DC/DC〉〉
Where DDCTL = Low or open, DC/DC and LDO operate at the same time.
〈〈Turning off DC/DC〉〉
Where DDCTL = High, DC/DC is compulsorily stopped and only LDO operates.
When DDCTL is switched from H to L (or open), LDO stops temporarily and DC/DC starts with soft start and then
LDO restart. If you switch DDCTL during IC operation, make sure that the output waveforms of DC/DC and LDO
are normal.
No.A2145-6/9
LV56351HA
Output voltage setting
Output voltages are given by the following formulas.
DCDCOUT = (1+R2/R1 ) × VREF [V]
LDOOUT = (1+R4/R3 ) × VREF [V]
〈〈Resistance for output setting〉〉
DC/DC OUT
LDOOUT
R2
IN1
R4
IN2
R1
R3
Start and stop
Start: Make sure to input EN signal (L ⇒ H) after supplying VCC = 12V.
Stop: Reverse-operation of start.
〈〈Output waveform during start and stop〉〉
Softstart
2.8ms
DC/DC boost output
LDO output
16V
15V
12V (=VCC)
5ms
0V
Delay
500μs
Time
EN
No.A2145-7/9
LV56351HA
Block diagram and Application circuit 1 (for BS antenna)
Condition: VCC = 12V, DCDCOUT = 16V, LDOOUT = 15V
VCC=12V
VCC
DC/DC
Boost
Converter
VREG
+
+
-
IN1
+
OSC
Soft
Start
P by P
LDOIN
FB
+
SCP
PGOOD
DDCTL
LDOOUT
ILimit
EN
High
Enable
DC/DC OUT=16V
SW
VREF
DC/DCOUT
(LDOIN)
PGOOD
SCP
UVLO
TSD
DC/DC
Control
LDOOUT=15V
IO=300mA
IN2
LDO
SGND PGND
〈〈Note〉〉
When LDOOUT is in the over current state or the short-circuit state, IC and external parts are protected by over current
limiter of LDO. And when DC/DCOUT is short-circuited, IC stops by timer latch-off type SCP function.
Application circuit 2 (for BS/CS antenna)
BS condition: VCC = 12V, DCDCOUT = 16V, LDOOUT = 15V
CS condition: VCC = 12V, DCDC = OFF, LDOOUT = 11V
VCC=12V
VCC
DC/DC
Boost
Converter
VREG
+
+
-
IN1
Soft
Start
+
OSC
P by P
LDOIN
FB
+
SCP
PGOOD
ILimit
PGOOD
SCP
UVLO
TSD
EN
2V
DDCTL
DC/DC OUT=16V/11.7V
SW
VREF
DC/DCOUT
(LDOIN)
DC/DC
Control
DDCTL=L : LDOOUT=15V
DDCTL=H : LDOOUT=11V
LDOOUT
LDOOUT=15V/11V
IO=300mA
IN2
Tr for LDO output switching
SGND PGND
LDO
No.A2145-8/9
LV56351HA
〈〈Addition〉〉
The above application circuit enables switching between 15V for BS and 11V for CS.
Where DDCTL=L, DC/DC booster is turned on and set as follows: DC/DCOUT=16V, LDOOUT=15V
Where DDCTL=H, DC/DC booster is turned off and set as follows: DC/DCOUT=11.7V, LDOOUT=11V
(because the resistance value of output setting of LDO is switched)
〈〈Output waveform at switching〉〉
LDOOUT = 15V ⇒ 11V
LDOOUT = 11V ⇒ 15V
5ms
16V
15V
DC/DC OUT
LDOOUT
12V (=VCC)
11V
Delay+Softstart
3.3ms
16V
15V
12V (=VCC)
11V
Time
DDCTL
DC/DC OUT
LDOOUT
Time
DDCTL
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
Regarding monolithic semiconductors, if you should intend to use this IC continuously under high temperature,
high current, high voltage, or drastic temperature change, even if it is used within the range of absolute
maximum ratings or operating conditions, there is a possibility of decrease reliability. Please contact us for a
confirmation.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellectual property rights which has resulted from the use of the technical information and products mentioned
above.
This catalog provides information as of October, 2012. Specifications and information herein are subject
to change without notice.
PS No.A2145-9/9
Similar pages