MICROSEMI LXM1611-01

P
P
A T E N T S
E N D I N G
TM
RangeMAX
LIN D O C #: 1611
LXM1611-01
D I G I TA L D I M M I N G C C F L I N V E RT E R M O D U L E
T
H E
I
N F I N I T E
P
O W E R
I
O F
P
N N O VA T I O N
R E L I M I N A R Y
DESCRIPTION
RangeMAX Wide Range Dimming, Single
Output Inverter. The LXM1611 series of
Direct DriveTM CCFL (Cold Cathode Fluorescent Lamp) Inverter Modules are specifically
designed for driving LCD backlight lamps.
Similar to the LXM1610, the LXM1611 excels in applications where critical parameters
include very wide range dimmability, high
efficiency and reliable fail-safe design in a
small form factor.
Unlike the LXM1610 or any traditional
dimming CCFL inverters, the LXM1611 provides the designer a vastly superior display
brightness range. 100:1+ brightness range
is achievable with virtually any LCD display.
Our wide range dimming provides exceptional display readability at less than 1% of
full brightness, allowing both power savings
and low ambient light operating capability
(i.e. "night readable").
The LXM1611 is recommended for use in
panels with low-voltage insulation on the
lamp return wire.
RangeMAX Digital Dimming Technique. Digital dimming provides flickerfree brightness control in any wide-range
dimming application. Dimming ratios greater
than 100:1 can be achieved. Incorporation
of a video synchronization feature allows
wide ratio dimming without the display disturbances and interference seen with competitive products.
D
A T A
S
H E E T
K E Y F E AT U R E S
The modules are equipped with a dimming
input that permits brightness control from an
external potentiometer or DC voltage source.
The resultant "burst drive" that energizes the
lamp was designed specifically to ensure that
no premature lamp degradation occurs. (See
"How RangeMAX Works" Section)
Wide Input Voltage Range. The modules convert unregulated DC voltage from the
system battery or AC adapter directly to highfrequency, high-voltage waves required to
ignite and operate CCFL lamps.
Direct Drive Technology. The module
design is based on a new Direct Drive topology, which provides a number of cost and
performance advantages. The LXM1611-01
series Direct Drive inverters eliminate the classic resonant inductor and capacitors, thus
reducing cost and allowing a 30% reduction
in module size.
Additional Features. Other benefits of
this new topology are fixed-frequency operation and secondary-side strike-voltage
regulation.
Strike-voltage regulation minimizes corona
discharge in the output transformer and related circuitry, providing longer life and higher
reliability. All LXM1611 modules feature both
open and shorted lamp protection.
The LXM1611 is fully customizable (electronically and mechanically) to specific customer requirements.
■
■
■
■
■
■
RangeMAX Wide Range Dimming
8V to 18V Input Voltage Range
30% Smaller Than CS-ZVS Models
Easy To Use Brightness Control
MicroAmp SLEEP Mode
Output Short-Circuit Protection And
Automatic Strike-Voltage Regulation
■ 7.3mm Max. Module Height, 16mm Module
Width
■ Fixed Frequency Operation
A P P L I C AT I O N S
■
■
■
■
Notebook And Sub-Notebook Computers
Portable Instrumentation
Desktop Displays
Low Ambient Light Conditions (i.e. Aircraft
Cabins, Automobile)
BENEFITS
■ High Efficiency And Sleep Mode Feature
Extends Computer Battery Life
■ Smooth, Flicker Free 1-100% Full-Range
Brightness Control Gives Your Product A
High Quality Image
■ Output Open Circuit Voltage Regulation
Minimizes Corona Discharge For Long Life
And High Reliability
■ Power Efficient, "Low Brightness" Capability
Allows For Advanced Power Management
NOTE: For current data & package dimensions, visit our web site: http://www.linfinity.com.
PRODUCT HIGHLIGHT
RANGEMAX
Power Used (Watts)
5
VS.
ANALOG DIMMING
Standard Analog
Dimming Inverter
4
3
LinFinity's
RangeMAX
2
1
0
30
45
60
75
90
■ RangeMAX technology allows the designer to operate
in a lower "brightness" and therefore at lower "power
consumption" than can be reached using traditional
analog dimming inverters.
■ Dotted line indicates area where panel variations and
parasitics will impact minimum light level with analog
dimming.
■ Data presented for a RangeMAX inverter driving a
13.3" LCD with a 1.2 Nit to 120 Nit brightness range.
The minimum power levels were 0.4 watts
(RangeMAX) vs. 2.1 watts (analog dimming) for a
power consumption savings of 1.7 watts.
105
Light Output (Nits)
M O D U L E O R D E R I N F O R M AT I O N
LXM1611-01
Copyright © 1999
Rev. 0.4 8/99
LINFINITY MICROELECTRONICS INC.
11861 WESTERN AVENUE, GARDEN GROVE, CA. 92841, 714-898-8121, FAX: 714-893-2570
1
P AT E N T P E N D I N G
PRODUCT DATABOOK 1996/1997
TM
RangeMAX
LXM1611-01
D I G I TA L D I M M I N G C C F L I N V E RT E R M O D U L E
P
R E L I M I N A R Y
D
A T A
S
H E E T
A B S O L U T E M A X I M U M R AT I N G S
(Note 1)
Input Supply Voltage (VIN) ........................................................................................................................................................ -0.3V to 18V
Output Voltage, no load .............................................................................................................................. Internally Limited to 1800VRMS
Output Current ............................................................................................................................................. 10.0mARMS (Internally Limited)
Output Power ........................................................................................................................................................................................ 6.0W
Input Signal Voltage (BRITE Input) ....................................................................................................................................... -0.3V to 6.5V
Input Signal Voltage (SLEEP, VSYNC(-), VSYNC(+) Inputs) ............................................................................................................... -0.3V to VIN
Ambient Operating Temperature .............................................................................................................................................. 0°C to 70°C
Storage Temperature Range ................................................................................................................................................... -40°C to 85°C
Note 1.
Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of the specified terminal.
R E C O M M E N D E D O P E R A T I N G C O N D I T I O N S (R.C.)
This module has been designed to operate over a wide range of input and output conditions. However, best efficiency and performance
will be obtained if the module is operated under the condition listed in the 'R.C.' column. Min. and Max. columns indicate values beyond
which the inverter, although operational, will not function optimally.
Parameter
Symbol
Input Supply Voltage Range (Functional)
Input Supply Voltage (Fully Regulated Lamp Current)
Output Power
Brightness Control Input Voltage Range
Lamp Operating Voltage
Lamp Current (Full Brightness)
Operating Ambient Temperature Range
VIN
PO
VBRT ADJ
VLAMP
IOLAMP
TA
Recommended Operating Conditions
Min.
R.C.
Max.
8
9
0.0
300
12
12
4
Units
18
16
5
2.5
800
675
7.0
0
V
V
W
V
VRMS
mARMS
°C
70
ELECTRICAL CHARACTERISTICS
Unless otherwise specified, these specifications apply over the recommended operating conditions and 25°C ambient temperature for the LXM1611.
Parameter
Symbol
Test Conditions
IL (MAX)
IL (MIN)
VLS
fO
VBRT ADJ = 2.5VDC, SLEEP = HIGH, Burst Duty = 100%, VIN = 9VDC
VBRT ADJ = 0VDC, SLEEP = HIGH, Burst Duty = 2%, VIN = 9VDC
0°C < TA < 40°C, VIN ≥ 7.0VDC
VBRT ADJ = 2.5VDC, SLEEP = HIGH, VIN = 12VDC
LXM1611-01
Min. Typ.
Max.
Units
Output Pin Characteristics
Full Bright Lamp Current
Minimum Lamp Current (Note 2)
Lamp Start Voltage
Operating Frequency
6.3
1500
52
7.0
0.14
7.7
57
1800
62
mARMS
mA RMS
VRMS
KHz
-12
2.5
0
-14
2.6
0
µADC
VDC
VDC
120
VIN
0.8
180
VDC
VDC
µADC
66
6.5
1.0
75
250
150
VDC
VDC
kΩ
µs
Hz
10
50
µADC
BRITE Input
Input Current
Input Voltage for Max. Lamp Current
Input Voltage for Min. Lamp Current
IBRT
VC
VC
VBRT ADJ = 0VDC
IO (LAMP) = 100% Duty Cycle
IO (LAMP) = Minimum Duty Cycle
-10
SLEEP Input
RUN Mode
SLEEP Mode
Input Current
VSLEEP (HI)
VSLEEP (LO)
ISLEEP
2.2
-0.3
SLEEP = 5.0V
VSYNC(-) / VSYNC(+) Characteristics
Logic High Level
Logic Low Level
Input Impedance
Pulse Width (Note 3)
Input Frequency
VSYNCH (HI)
VSYNCH (LO)
ZIN
tPW
fSYNC
4.0
-0.3
60
25
49
Power Characteristics
Sleep Current
IIN (MIN)
VIN = 15VDC , SLEEP ≤ 0.8V
Note 2. Minimum lamp current required to maintain even light output may vary with display panel.
3. The module will be functional with pulse widths much larger than 250µs, but will have limited dimming.
2
Copyright © 1999
Rev. 0.4 8/99
PRODUCT DATABOOK 1996/1997
PATENT PENDING
TM
RangeMAX
LXM1611-01
D I G I TA L D I M M I N G C C F L I N V E RT E R M O D U L E
P
R E L I M I N A R Y
D
A T A
S
H E E T
FUNCTIONAL PIN DESCRIPTION
Conn.
CN1
Pin
Description
CN1-1
CN1-2
VIN
Input Power Supply. (8V ≤ VIN ≤ 18V)
CN1-3
CN1-4
GND
Power Supply Return.
CN1-5
SLEEP
ON/OFF Control. (2.2V < SLEEP < VIN = ON, -0.3V < SLEEP < 0.8V = OFF)
CN1-6
BRITE
Brightness Control (-0.3 to 2.5VDC).
CN1-7
VSYNC(-)
Vertical syncronization input, negative going.
CN1-8
VSYNC(+)
Vertical syncronization input, positive going.
2.5VDC gives maximum lamp current.
}
25µs < tPW < 250µs, 49Hz < fSYNC < 150Hz
CN2
CN2-1
VHI
High voltage connection to high side of lamp. Connect to lamp terminal with shortest lead length.
DO NOT connect to ground.
CN2-2
VLO
Connection to low side of lamp. Connect to lamp terminal with longer lead length.
DO NOT connect to Ground.
PHYSICAL DIMENSIONS
LXM1611-01
All dimensions are in inches (mm).
3.93 (100)
2.36 (60)
1.20 (30.5)
Ø 0.116 (2.95)
Grounded Mounting Hole
0.15
(3.85)
CN2
CN1
2.06 (52.25)
0.64
(16)
Warning!!
High Voltage
Present
0.287 Max. (7.3)
0.031 (0.79) max.
Copyright © 1999
Rev. 0.4 8/99
Connectors:
CN-1 = MOLEX 53261-0890
Recommended Mate:
Pins: 50079-8100*, Housing: 51021-0800
CN-2 = JST SM02(8.0) B-BHS-TB
Pins: 5BH-001T-P0.5, Housing: BHR-03VS-1
* Loose (-8000, Chain) Recommended #26 AWG wiring
3
P AT E N T P E N D I N G
PRODUCT DATABOOK 1996/1997
TM
RangeMAX
LXM1611-01
D I G I TA L D I M M I N G C C F L I N V E RT E R M O D U L E
P
R E L I M I N A R Y
D
A T A
S
H E E T
HOW RANGEMAX WORKS
LAMP VOLTAGE & LAMP CURRENT — Burst Mode Operation
(770VRMS)
(760VRMS)
(7.6mARMS)
(6.7mARMS)
FIGURE 1 — 50% Burst Duty Cycle
FIGURE 2 — 2% Burst Duty Cycle
Rather than using the traditional dimming technique of
varying lamp current magnitude to adjust light output,
RangeMAX inverters use a fixed lamp current value with
a duty cycle control method.
The lamp current burst width can be modulated from
100% (continuous lamp current) down to a 2% duty cycle,
allowing the lamp to be dimmed to less than 1% of its
full brightness.
As can be seen in Trace 4 of Figure 3 photo at right,
careful design consideration was given to controlling lamp
start voltage to softly start current flow. This eliminates
current overshoot that can result in premature cathode
wear and reduce lamp life.
(6.7mARMS)
FIGURE 3 — 2% Burst Duty Cycle (Expanded Time Base)
High Voltage
Transformer
Comparator
VBRITE
Ramp
VHI
Transformer
Driver
LAMP
0-2.5V
DC
(760VRMS)
Ramp
Gen.
VSYNC(-)
VSYNC(+)
VSENSE
ISENSE
VLO
FIGURE 4 — RangeMAX Block Diagram
4
Copyright © 1999
Rev. 0.4 8/99
PRODUCT DATABOOK 1996/1997
TM
RangeMAX
PATENT PENDING
LXM1611-01
D I G I TA L D I M M I N G C C F L I N V E RT E R M O D U L E
P
R E L I M I N A R Y
D
A T A
S
H E E T
H O W R A N G E M A X W O R K S (continued)
HIGHLIGHTS
■ On-board brightness control circuit includes a DC voltage
to pulse width converter that minimizes system design work
and system noise susceptibility. This provides a familiar
and convenient interface while reducing the potential for
externally induced noise which can cause lamp flicker.
■ An on-board oscillator operates the inverter BURST rate
above 95Hz, well beyond standard 50/60Hz video refresh
rates where the eye can perceive pulsing light.
■ RangeMAX inverter modules are designed to operate with
the burst frequency synchronized to the video frame rate.
This provides operation with no visible display disturbances
caused by beat frequencies between the lamps and video
frame rates.
■ In applications with no access to a vertical sync, the inverter burst frequency can be allowed to "free run" at 95Hz.
In this non-synchronous mode, minor display disturbances
can be found under certain video conditions. This performance may be acceptable for many applications, but synchronization must be used when no disturbance can be
tolerated.
■ Separate inputs are provided for negative and positive vertical sync pulses so external inversion is not needed.
■ Separate feedback loops for lamp current and open circuit
voltage regulation insure reliable strike under all operating conditions, automatic over-voltage prevention with broken or failed lamps, and accurate lamp current regulation.
T Y P I C A L A P P L I C AT I O N
2.5VDC
£ 10k
9-18VDC
VIN
BRITE
VHI
CCFL
TUBE
LXM1611-01
5V
0V
SLEEP
VSYNC(-)
VSYNC(+)
GND
VLO
VSYNC(-)
VSYNC(+)
FIGURE 5 — Potentiometer Brightness Control
PWM Signal
from System
P.W.
4.99k
4.7µF
BRITE
4.99k*
■ The brightness control may be a simple 10k
potentiometer or a voltage output DAC. A PWM signal
from a micro-controller may also be used with a suitable
filter such as shown in Figure 5A.
■ If synchronization to the video framerate is desired,
connect the vertical sync pulse from the system video
controller to the appropriate VSYNC input. If the pulse
is negative going (
), connect it to VSYNC(-). If
), connect it to VSYNC(+).
positive going (
If no video synchronization is desired, leave both VSYNC(-)
and VSYNC(+) floating.
■ If you need to turn the inverter ON/OFF remotely,
connect a 3V or 5V logic signal to the SLEEP input. If
remote ON/OFF is not needed, connect the SLEEP input
to VIN or any other voltage greater than 2.2VDC.
■ Connect VHI to high voltage wire from the lamp.
Connect VLO to the low voltage wire (wire with thinner
insulation). Never connect VLO to circuit ground as
this will defeat lamp current regulation. If both lamp
wires have heavy high voltage insulation, connect the
longest wire to VLO.
LXM1611-01
£ 100µs
0 £ P.W. £ 100% of period
* Use 4.99k for 5V PWM amplitude, 15k for 3.3V PWM
amplitude, and omit for 2.5V PWM amplitude.
FIGURE 5A — PWM Brightness Control
RangeMAX INVERTERS
Also available in Dual
Output LXM1621-01 and
Quad Output LXM1641-01
versions for multiple lamp
applications.
RangeMAX and Direct Drive are trademarks of Linfinity Microelectronics Inc.
PRELIMINARY DATA - Information contained in this document is pre-production data, and is proprietary to LinFinity. It may
not modified in any way without the express written consent of LinFinity. Product referred to herein is offered in sample form
only, and Linfinity reserves the right to change or discontinue this proposed product at any time.
Copyright © 1999
Rev. 0.4 8/99
5