Sharp LZ0P3620 1/4-type built-in lens color ccd area sensors with 320 k pixel Datasheet

LZ0P3620/3621/3622/3625
LZ0P3620/3621/
3622∫/3625∫
1/4-type Built-in Lens Color CCD
Area Sensors with 320 k Pixels
∫Under development
• Package
– 14-pin half-pitch WLCC* type
– Base section size : 12 mm (H) x 11 mm (V)
– Outline dimensions (MAX.) : 18 mm (H) x 11 mm (V)
• Package height
– Approx. 10 mm (single lens) : LZ0P3620
– Approx. 13 mm (two pcs. of lenses) :
LZ0P3621/22∫/25∫
DESCRIPTION
The LZ0P3620/21/22∫/25∫ are 1/4-type (4.5 mm)
320 000-pixel built-in lens color CCD (chargecoupled device) area sensors. With their small lens
and WLCC-type flat package, it is possible to make
ultra small color camera easily.
FEATURES
* Window Leadless Chip Carrier
• Number of effective pixels : 512 (H) x 582 (V)
• Number of optical black pixels
– Horizontal : 2 front and 28 rear
• Pixel pitch : 7.2 µm (H) x 4.7 µm (V)
• Mg, G, Cy, and Ye complementary color filters
• Low fixed-pattern noise and lag
• Blooming suppression structure
• Built-in output amplifier
• Built-in overflow drain voltage circuit and reset
gate voltage circuit
• Horizontal shift register clock and reset gate clock
voltage : 3.3 V (TYP.)
• Variable electronic shutter (1/50 to 1/10 000 s)
• Compatible with PAL standard
• Built-in optical low-pass-filter
• Integrated lens :
Horizontal viewing angle
LZ0P3620 : 52˚
LZ0P3621 : 50˚
∫LZ0P3622 : 62˚
∫LZ0P3625 : 115˚
PIN CONNECTIONS
14-PIN HALF-PITCH WLCC TYPE
TOP VIEW
OD
1
14
GND
ØRS
2
13
ØV4
NC1
3
12
ØV3
OS
4
11
ØV2
NC2
5
10
ØV1
ØH2
6
9
PW
ØH1
7
8
OFD
COMPARISON TABLE
Horizontal viewing angle
Number of integrated lenses
Package height
Characteristics
LZ0P3620
52˚
LZ0P3621
50˚
∫LZ0P3622
62˚
Single
Two pcs.
Approx. 10 mm
Approx. 13 mm
∫LZ0P3625
115˚
Refer to each following specification.
Lens specification
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in
catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
1
LZ0P3620/3621/3622/3625
PIN DESCRIPTION
SYMBOL
OD
PIN NAME
Output transistor drain
OS
ØRS
Output signals
ØV1, ØV2, ØV3, ØV4
Vertical shift register clock
Reset transistor clock
ØH1, ØH2
Horizontal shift register clock
OFD
PW
Overflow drain
P-well
GND
Ground
NC1, NC2
No connection
ABSOLUTE MAXIMUM RATINGS
(TA = +25 ˚C)
SYMBOL
VOD
RATING
0 to +18
UNIT
V
NOTE
Overflow drain voltage
VOFD
Reset gate clock voltage
VØRS
Internal output
Internal output
V
V
1
2
V
V
PARAMETER
Output transistor drain voltage
Vertical shift register clock voltage
VØV
Horizontal shift register clock voltage
VØH
–10.5 to +17.5
–0.3 to +12
Voltage difference between P-well and vertical clock
VPW-VØV
–28 to 0
V
Voltage difference between vertical clocks
VØV-VØV
V
˚C
˚C
Storage temperature
TSTG
0 to +15
–20 to +70
Ambient operating temperature
TOPR
–10 to +60
3
NOTES :
1. Do not connect to DC voltage directly. When OFD is connected to GND, connect VOD to GND. Overflow drain clock is
applied below 26 Vp-p.
2. Do not connect to DC voltage directly. When ØRS is connected to GND, connect VOD to GND. Reset gate clock is
applied below 8 Vp-p.
3. When clock width is below 10 µs, and clock duty factor is below 0.1%, voltage difference between vertical clocks will be
below 27 V.
2
LZ0P3620/3621/3622/3625
RECOMMENDED OPERATING CONDITIONS
PARAMETER
Ambient operating temperature
SYMBOL
TOPR
MIN.
TYP.
25.0
MAX.
UNIT
˚C
Output transistor drain voltage
VOD
14.55
15.0
15.45
V
Overflow drain clock p-p level
VØOFD
21.5
23.5
V
Ground
P-well voltage
GND
VPW
LOW level
Vertical shift
VØV1L, VØV2L
VØV3L, VØV4L
–9.0
–8.5
VØV1I, VØV2I
register clock
INTERMEDIATE level
HIGH level
VØV3I, VØV4I
VØV1H, VØV3H
Horizontal shift
register clock
LOW level
VØH1L, VØH2L
HIGH level
Reset gate clock p-p level
0.0
–8.0
NOTE
1
V
VØVL
V
–7.5
V
0.0
2
V
14.55
15.0
15.45
V
VØH1H, VØH2H
–0.05
3.0
0.0
3.3
0.05
5.25
V
V
VØRS
3.0
3.3
5.25
V
Vertical shift register clock frequency
fØV1, fØV2
fØV3, fØV4
15.63
kHz
Horizontal shift register clock frequency
Reset gate clock frequency
fØH1, fØH2
fØRS
9.66
9.66
MHz
MHz
1
NOTES :
• Connect NC1 and NC2 to GND directly or through a capacitor larger than 0.047 µF.
1. Use the circuit parameter indicated in "SYSTEM CONFIGURATION EXAMPLE", and do not connect to DC voltage directly.
2. VPW is set below VØVL that is low level of vertical shift register clock, or is used with the same power supply that is connected
to VL of V driver IC.
* To apply power, first connect GND and then turn on VOD. After turning on VOD, turn on PW first and then turn on other powers
and pulses. Do not connect the device to or disconnect it from the plug socket while power is being applied.
3
LZ0P3620/3621/3622/3625
CHARACTERISTICS FOR LZ0P3620 (Drive method : Field accumulation)
(TA : +25 ˚C, Operating conditions : The typical values specified in "RECOMMENDED OPERATING CONDITIONS".
Color temperature of light source : 3 200 K)
PARAMETER
Standard output voltage
Saturation output voltage
Sensitivity
Resolution (at center)
Resolution (at corner)
Shading
Difference of center position
Output transistor drain current
SYMBOL
VO
VSAT
R
MIN.
700
350
250
150
50
IOD
TYP.
150
MAX.
450
300
200
65
4.0
±10
8.0
UNIT
mV
mV
mV
TV line
TV line
%
%
mA
NOTE
1
2
3
4
5
6
7
NOTES :
can be distinguished on the B/W video monitor.
5. The resolution in the peripheral area (image height : Y =
0.8) under the conditions mentioned above.
6. Defined by the following formula at the brightness of
standard output voltage : (Vco/Vce) x 100 [%]
Vco : Output voltage at edge of the image (at video output).
Vce : Output voltage at center of the image (at video output).
7. The difference between the center position of image and
that of the monitor. This is the ratio for the horizontal
underscanning monitor size which includes the decentering
eccentricity when turning the lens head one time.
1. The average output voltage in the central area (H/10,
V/10) under uniform illumination.
The standard exposure conditions are defined as when
VO is 150 mV.
2. The average output voltage in the central area (H/10,
V/10) under 10 times exposure of the standard exposure
conditions.
3. The average output voltage in the central area (H/10,
V/10) when a 1 000 lux light source with a white board
of 90% reflector is imaged.
4. The resolution in the central area (H/10, V/10) at which
the image of the TV resolution chart (ex. EIAJ test chart)
LENS SPECIFICATION FOR LZ0P3620
PARAMETER
Construction
Focal length
F No.
Viewing angle
TV distortion
Focus adjustment range
Torque of focusing
SPECIFICATION
Single (non-spherical, plastic)
4.0 mm [TYP. : reference]
2.8±5%
H : 52˚, V : 40˚, Diagonal : 65˚ [TYP. : reference]
≤ –3.2%
∞ to 10 cm
0.00005 to 0.001 N·m
NOTE
1
2
3
NOTES :
1. TV distortion is defined by the formula, (∆y/y) x 100 [%]
at capturing rectangular pattern sized horizontal by
vertical as 4 by 3.
"y" is defined as the vertical height of the center of the
horizontal line.
∆y is defined as the difference between the vertical height
of the center of the horizontal line and an edge of it.
2. The best focus point of an object can be obtained by
turning the lens head within this range.
3. Torques which are necessary for turning the lens.
* Be careful not to remove the lens head by turning it
counterclockwise too much when adjusting macro.
∆y
y
4
LZ0P3620/3621/3622/3625
CHARACTERISTICS FOR LZ0P3621 (Drive method : Field accumulation)
(TA : +25 ˚C, Operating conditions : The typical values specified in "RECOMMENDED OPERATING CONDITIONS".
Color temperature of light source : 3 200 K)
PARAMETER
Standard output voltage
Saturation output voltage
Sensitivity
Resolution (at center)
Resolution (at corner)
Shading
Difference of center position
Output transistor drain current
SYMBOL
VO
VSAT
R
MIN.
700
350
250
150
40
IOD
TYP.
150
MAX.
450
300
200
60
4.0
±10
8.0
UNIT
mV
mV
mV
TV line
TV line
%
%
mA
NOTE
1
2
3
4
5
6
7
NOTES :
can be distinguished on the B/W video monitor.
5. The resolution in the peripheral area (image height : Y =
0.8) under the conditions mentioned above.
6. Defined by the following formula at the brightness of
standard output voltage : (Vco/Vce) x 100 [%]
Vco : Output voltage at edge of the image (at video output).
Vce : Output voltage at center of the image (at video output).
7. The difference between the center position of image and
that of the monitor. This is the ratio for the horizontal
underscanning monitor size which includes the decentering
eccentricity when turning the lens head one time.
1. The average output voltage in the central area (H/10,
V/10) under uniform illumination.
The standard exposure conditions are defined as when
VO is 150 mV.
2. The average output voltage in the central area (H/10,
V/10) under 10 times exposure of the standard exposure
conditions.
3. The average output voltage in the central area (H/10,
V/10) when a 1 000 lux light source with a white board
of 90% reflector is imaged.
4. The resolution in the central area (H/10, V/10) at which
the image of the TV resolution chart (ex. EIAJ test chart)
LENS SPECIFICATION FOR LZ0P3621
PARAMETER
Construction
Focal length
F No.
Viewing angle
TV distortion
Focus adjustment range
Torque of focusing
SPECIFICATION
2 pcs. (non-spherical, plastic)
3.9 mm [TYP. : reference]
2.8±5%
H : 50˚, V : 38˚, Diagonal : 60˚ [TYP. : reference]
≤ –1.0%
∞ to 10 cm
0.00005 to 0.001 N·m
NOTE
1
2
3
NOTES :
1. TV distortion is defined by the formula, (∆y/y) x 100 [%]
at capturing rectangular pattern sized horizontal by
vertical as 4 by 3.
"y" is defined as the vertical height of the center of the
horizontal line.
∆y is defined as the difference between the vertical height
of the center of the horizontal line and an edge of it.
2. The best focus point of an object can be obtained by
turning the lens head within this range.
3. Torques which are necessary for turning the lens.
* Be careful not to remove the lens head by turning it
counterclockwise too much when adjusting macro.
∆y
y
5
LZ0P3620/3621/3622/3625
CHARACTERISTICS FOR LZ0P3622∫ (Drive method : Field accumulation)
∫Under development
(TA : +25 ˚C, Operating conditions : The typical values specified in "RECOMMENDED OPERATING CONDITIONS".
Color temperature of light source : 3 200 K)
PARAMETER
Standard output voltage
Saturation output voltage
Sensitivity
Resolution (at center)
Resolution (at corner)
Shading
Difference of center position
Output transistor drain current
SYMBOL
VO
VSAT
R
MIN.
700
350
250
150
IOD
TYP.
150
MAX.
450
300
200
50
4.0
±10
8.0
UNIT
mV
mV
mV
TV line
TV line
%
%
mA
NOTE
1
2
3
4
5
6
7
NOTES :
can be distinguished on the B/W video monitor.
5. The resolution in the peripheral area (image height : Y =
0.8) under the conditions mentioned above.
6. Defined by the following formula at the brightness of
standard output voltage : (Vco/Vce) x 100 [%]
Vco : Output voltage at edge of the image (at video output).
Vce : Output voltage at center of the image (at video output).
7. The difference between the center position of image and
that of the monitor. This is the ratio for the horizontal
underscanning monitor size which includes the decentering
eccentricity when turning the lens head one time.
1. The average output voltage in the central area (H/10,
V/10) under uniform illumination.
The standard exposure conditions are defined as when
VO is 150 mV.
2. The average output voltage in the central area (H/10,
V/10) under 10 times exposure of the standard exposure
conditions.
3. The average output voltage in the central area (H/10,
V/10) when a 1 000 lux light source with a white board
of 90% reflector is imaged.
4. The resolution in the central area (H/10, V/10) at which
the image of the TV resolution chart (ex. EIAJ test chart)
LENS SPECIFICATION FOR LZ0P3622∫
PARAMETER
Construction
Focal length
F No.
Viewing angle
TV distortion
Focus adjustment range
Torque of focusing
SPECIFICATION
2 pcs. (non-spherical, plastic)
3.0 mm [TYP. : reference]
2.8±5%
H : 62˚, V : 49˚, Diagonal : 74˚ [TYP. : reference]
≤ –1.0%
∞ to 10 cm
0.00005 to 0.001 N·m
NOTE
1
2
3
NOTES :
1. TV distortion is defined by the formula, (∆y/y) x 100 [%]
at capturing rectangular pattern sized horizontal by
vertical as 4 by 3.
"y" is defined as the vertical height of the center of the
horizontal line.
∆y is defined as the difference between the vertical height
of the center of the horizontal line and an edge of it.
2. The best focus point of an object can be obtained by
turning the lens head within this range.
3. Torques which are necessary for turning the lens.
* Be careful not to remove the lens head by turning it
counterclockwise too much when adjusting macro.
∆y
y
6
LZ0P3620/3621/3622/3625
CHARACTERISTICS FOR LZ0P3625∫ (Drive method : Field accumulation)
∫Under development
(TA : +25 ˚C, Operating conditions : The typical values specified in "RECOMMENDED OPERATING CONDITIONS".
Color temperature of light source : 3 200 K)
PARAMETER
Standard output voltage
Saturation output voltage
Sensitivity
Resolution (at center)
Resolution (at corner)
Shading
Difference of center position
Output transistor drain current
SYMBOL
VO
VSAT
R
MIN.
700
350
IOD
TYP.
150
MAX.
450
300
200
45
4.0
±10
8.0
UNIT
mV
mV
mV
TV line
TV line
%
%
mA
NOTE
1
2
3
4
5
6
7
NOTES :
can be distinguished on the B/W video monitor.
5. The resolution in the peripheral area (image height : Y =
0.8) under the conditions mentioned above.
6. Defined by the following formula at the brightness of
standard output voltage : (Vco/Vce) x 100 [%]
Vco : Output voltage at edge of the image (at video output).
Vce : Output voltage at center of the image (at video output).
7. The difference between the center position of image and
that of the monitor. This is the ratio for the horizontal
underscanning monitor size which includes the decentering
eccentricity when turning the lens head one time.
1. The average output voltage in the central area (H/10,
V/10) under uniform illumination.
The standard exposure conditions are defined as when
VO is 150 mV.
2. The average output voltage in the central area (H/10,
V/10) under 10 times exposure of the standard exposure
conditions.
3. The average output voltage in the central area (H/10,
V/10) when a 1 000 lux light source with a white board
of 90% reflector is imaged.
4. The resolution in the central area (H/10, V/10) at which
the image of the TV resolution chart (ex. EIAJ test chart)
LENS SPECIFICATION FOR LZ0P3625∫
PARAMETER
Construction
Focal length
F No.
Viewing angle
TV distortion
Focus adjustment range
Torque of focusing
SPECIFICATION
2 pcs. (non-spherical, plastic)
1.53 mm [TYP. : reference]
2.8±5%
H : 115˚, V : 89˚, Diagonal : 138˚ [TYP. : reference]
≤ –14%
∞ to 10 cm
0.00005 to 0.001 N·m
NOTE
1
2
3
NOTES :
1. TV distortion is defined by the formula, (∆y/y) x 100 [%]
at capturing rectangular pattern sized horizontal by
vertical as 4 by 3.
"y" is defined as the vertical height of the center of the
horizontal line.
∆y is defined as the difference between the vertical height
of the center of the horizontal line and an edge of it.
2. The best focus point of an object can be obtained by
turning the lens head within this range.
3. Torques which are necessary for turning the lens.
* Be careful not to remove the lens head by turning it
counterclockwise too much when adjusting macro.
∆y
y
7
LZ0P3620/3621/3622/3625
PIXEL STRUCTURE
OPTICAL BLACK
(2 PIXELS)
OPTICAL BLACK
(28 PIXELS)
512 (H) x 582 (V)
1 pin
COLOR FILTER ARRAY
(1, 582)
1st, 3rd
field
(512, 582)
G
Mg
G
Mg
G
Mg
G
Mg
G
Mg
Cy
Ye
Cy
Ye
Cy
Ye
Cy
Ye
Cy
Ye
Mg
G
Mg
G
Mg
G
Mg
G
Mg
G
Cy
Ye
Cy
Ye
Cy
Ye
Cy
Ye
Cy
Ye
G
Mg
G
Mg
G
Mg
G
Mg
G
Mg
Cy
Ye
Cy
Ye
Cy
Ye
Cy
Ye
Cy
Ye
G
Mg
G
Mg
G
Mg
G
Mg
G
Mg
Cy
Ye
Cy
Ye
Cy
Ye
Cy
Ye
Cy
Ye
Mg
G
Mg
G
Mg
G
Mg
G
Mg
G
Cy
Ye
Cy
Ye
Cy
Ye
Cy
Ye
Cy
Ye
G
Mg
G
Mg
G
Mg
G
Mg
G
Mg
Cy
Ye
Cy
Ye
Cy
Ye
Cy
Ye
Cy
Ye
(1, 1)
2nd, 4th
field
(512, 1)
8
LZ0P3620/3621/3622/3625
TIMING CHART
VERTICAL TRANSFER TIMING
(1st, 3rd FIELD)
623
625 1
6
20
Shutter speed
22 1/2 000 s
HD
VD
ØV1
ØV2
ØV3
ØV4
ØOFD
580 582
+
581
1
+
2
3
+
4
5
+
6
7
+
8
1
2
+
3
4
+
5
6
+
7
OS
(2nd, 4th FIELD)
311
318
332
HD
VD
ØV1
ØV2
ØV3
ØV4
ØOFD
579 581
+
+
580 582
OS
HORIZONTAL TRANSFER TIMING
618, 1
60
HD
ØH1
ØH2
ØRS
OS
…512
OB (2)
OUTPUT (512) 1ππ
OB (28)
29
49
ØV1
39
59
ØV2
54
24
ØV3
34
64
ØV4
62
ØOFD
9
72
LZ0P3620/3621/3622/3625
READOUT TIMING
(1st, 3rd FIELD)
HD
1
60
618, 1
242
29 49
ØV1
39 59
ØV2
24
ØV3
29 49
161
54
34
ØV4
290
449
290
180
60
39 59
338
54
34
64
64
(2nd, 4th FIELD)
HD
ØV1
ØV2
ØV3
ØV4
1
60
618, 1
242
29 49
39 59
24 54
34
60
290
161
59
290
180
338
54
450
64
10
64
V4
V3B
V3A
V1B
VMa
V1A
VH
11
13 14 15 16 17 18 19 20 21 22 23 24
1
VOFDH
VH3BX
OFDX
V2X
V1X
VH1AX
V3X
VDD
GND
+
VH3AX
(*1) ØRS, OFD :
Use the circuit parameter indicated in
this circuit example, and do not connect
to DC voltage directly.
100 $
+
0.1 µF
6
5
4
3
2
(*1)
1
9
8
(*1)
10 11 12 13 14
LZ0P362X
7
OFD
+5 V
V3X
VH1AX
V1X
V2X
OFDX
NC
PW
VH3AX
V2
LR36685
VL
2
VMb
3
POFD
4
ØH1
5
ØH2
6
OS
7
NC2
8
NC1
9
OD
12 11 10
0.01 µF
ØRS
V4X
VOD
VL (VPW)
VH
ØRS
ØH2
ØH1
1 M$
ØV4
ØV1
+
V4X
VH1BX
+
270 pF
CCD
OUT
1 M$
LZ0P3620/3621/3622/3625
SYSTEM CONFIGURATION EXAMPLE
GND
ØV3
ØV2
PACKAGES FOR CCD AND CMOS DEVICES
PACKAGES
(Unit : mm)
14 WLCC TYPE
+0
18–0.2
Approx. 10
+0
14±0.1
2.0±0.1
5.0±0.1
+0
12
1.27
0.64
,,,,
,,,,
,,,,
,,,
,,, ,,,
,,, ,,,
,,, ,,,,
,,,, ,,,
,,, ,,,
,,, ,,,
,,,
,,,
,,, ,,,
,,, ,,,
,,, ,,,,
,,,, ,,,
,,, ,,,
,,, ,,,
,,,
,,, ,,, ,,, ,,,, ,,, ,,, ,,,
7.6±0.05
3.6
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,
+0
1.27
4-90˚
11–0.1
,,,,
,,,,
,,,,
No.1 index
+0
2-C0.2 –0.05
+0
,,,
,,,
,,,,
,,, ,,,
,,, ,,,
,,,
,,,, ,,,
,,, ,,,
,,,
,,,
,,,
,,,
,,, ,,,,
,,,
,,, ,,,
,,,
,,, ,,,
,,, ,,,,
,,, ,,,
,,, ,,,
,,, ,,,
,,,, ,,,
,,,
+0
2-Ø0.8–0.05
1.0±0.1
Ø11.0–0.1
No.1 index
+0
–0.1
11.0±0.05
Ø12.0
,,
,,
,,
,,
,,
Approx. 10
,,
,,
,,
,,
,,
2.0±0.1
+0
1.0 –0.1
1.6–0.05
0.8–0.05
+0
–0.1
5.0±0.1
Height 0.5
¿Applicable models¡
LZ0P3610/LZ0P3620
1.0±0.1
,,, ,,,
,,, ,,,
,,, ,,, ,,,
,,, ,,,
,,,
,,, ,,,
,,, ,,,
,,, ,,, ,,,
,,, ,,, ,,,
,,,
,,,
,,,
,,, ,,, ,,,
,,, ,,,
,,, ,,,
,,, ,,,
,,, ,,,
,,,
11.0±0.05
14 WLCC TYPE
+0
18–0.2
+0
Approx.12-13
0.8–0.05
±0.1
+0
12–0.1
1.27
0.64
5.0±0.1
+0
3.0±0.1
,,,,,,,,
,,,,,,,,
,,,,,,,,
No.1 index
+0
+0
,,,
,,,
,,,
,,,
,,,
,,,
,,,
,,,
¿Applicable models¡
LZ0P3611/12/15,
LZ0P3621/22/25,
LZ0P3641/42/45/46
1.0±0.1
11.0±0.05
5.0±0.1
Height 0.5
,,,, ,,,
,,, ,,,
,,, ,,,
,,, ,,,
,,,
,,,,
,,,, ,,,
,,, ,,,
,,, ,,,
,,, ,,,
,,, ,,,
,,, ,,,
,,,
,,,,
,,,, ,,,
,,, ,,,
,,, ,,, ,,,
,,, ,,,
,,, ,,,
+0
2-Ø0.8–0.05
11±0.05
Approx. 12
Ø12.0
2.0±0.1
+0
–0.05
,,, ,,, ,,, ,,, ,,, ,,, ,,,
,,, ,,, ,,, ,,, ,,, ,,, ,,,
,,, ,,,
,,, ,,,
,,, ,,,
,,, ,,,
,,,
,,, ,,,
,,, ,,,
,,, ,,,
,,, ,,,
,,, ,,, ,,,
,,,
3.0±0.1
2.0±0.1
2-C0.2–0.05
Ø11.0–0.05
,,,
,,,
,,,
,,,
,,,
,,,
,,,
,,,
,,, ,,, ,,, ,,, ,,, ,,, ,,,
,,, ,,, ,,, ,,, ,,, ,,, ,,,
,,,
,,, ,,,
,,,
,,, ,,,
,,,
,,, ,,,
,,, ,,,
,,,
,,,
,,,
,,, ,,,
,,, ,,,
,,,
,,, ,,,
3.6
,,,,,,,,
,,,,,,,,
,,,,,,,,
7.6±0.05
+0
11–0.1
1.27
4-90˚
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
No.1 index
1.6 –0.05
14
12
PRECAUTIONS FOR BUILT-IN LENS CCD AREA SENSORS
PRECAUTIONS FOR BUILT-IN LENS CCD
AREA SENSORS
1. Package Breakage
2. Electrostatic Damage
In order to prevent the package, the lens holder,
and the lens from being broken, follow the
instructions below :
1) The CCD is a precise optical component and
the package-base material is ceramic.
Therefore,
ø Take care not to drop the device when
mounting, handling, or transporting.
ø Avoid giving a shock to the package.
Especially when leads are fixed to the socket
or the circuit board, a small shock could
break the package more easily than when the
package isn’t fixed.
2) When adjusting the focus, screw the lens holder
to the circuit board before soldering the leads.
At that time, make sure to use a circuit board
with plenty of strength, and to avoid the
package and the lens holder from being broken,
the following screw and clamp torque are
recommended.
ø Recommended mounting screw :
Ø1.7 tapping screw (B-tight type),
Length, L = the thickness of the circuit board
+ 5 mm
ø Recommended clamp torque : 0.012 N·m
[however, when the thickness of the circuit
board is thinner than t = 2.0 mm]
3) If any damage or breakage occurs on the
surface of the lens, its characteristics could
deteriorate.
Therefore,
ø Do not hit the lens.
ø Do not give a shock large enough to cause
distortion.
ø Do not scrub or scratch the surface of the
lens.
– Even a soft cloth or applicator, if dry, could
cause dust to scratch the lens.
As compared with general MOS-LSI, CCD has
lower ESD. Therefore, take the following anti-static
measures when handling the CCD :
1) Always discharge static electricity by grounding
the human body and the instrument to be used.
To ground the human body, provide resistance
of about 1 M$ between the human body and
the ground to be on the safe side.
2) When directly handling the device with the
fingers, hold the lens holder and do not touch
the lead.
3) To avoid generating static electricity,
a. do not scrub the device with cloth or plastic.
b. do not attach any tape or labels.
c. do not clean the device with dust-cleaning
tape.
4) When storing or transporting the device, put it in
a container of conductive material.
3. Dust and Contamination
Dust or contamination on the surface of the lens
and the inside of the lens holder could deteriorate
the output characteristics or cause a scar. In order
to minimize dust or contamination on the device,
take the following precautions :
1) Do not remove the lens from the body.
Especially when adjusting macro, be careful not
to remove the lens by turning it counterclockwise too much.
2) Do not touch the surface of the lens with the
fingers. If dust or contamination gets on the
surface of the lens, the following cleaning
method is recommended :
ø Handle the built-in lens CCD in a clean
environment such as a cleaned booth. (The
cleanliness level should be, if possible, class
1 000 at least.)
13
PRECAUTIONS FOR BUILT-IN LENS CCD AREA SENSORS
ø Make sure there is no dust or contamination
on the lens and screw it on the lens holder.
ø Dust from static electricity should be blown
off with an ionized air blower. For antielectrostatic measures, however, ground all
the leads on the device before blowing off
the dust.
ø The contamination on the surface of the lens
should be wiped off with a clean applicator
soaked in isopropyl alcohol. Wipe slowly and
gently in one direction only.
– Frequently replace the applicator and do not
use the same applicator to clean more than
one device.
THE SHAPE OF
THE TEMPERATURE OF
THE IRON END
THE IRON END
4. Other
1) Soldering should be manually performed under
the following conditions :
ø Use ESD-measured soldering iron
ø The conditions of the soldering time in which
the soldering iron touches the package,
differs by the shape and the temperature of
the iron end. Refer to the table below and
take great care in soldering.
SOLDERING TIME
Ø3.2
R0.5
0.5
6.5
17
(Unit : mm)
17
(Unit : mm)
Below 350 ˚C
Time touching the package should be less than 40 seconds
Below 300 ˚C
Below 275 ˚C
Time touching the package should be less than 25 seconds
Time touching the package should be less than 35 seconds
2) There is no guarantee of the performance of
the device which has been removed or
resoldered after being soldered once under the
conditions mentioned above.
– In case there seems to be an inferior device,
consult with our sales office before removing
it.
3) Avoid using or storing the CCD at high
temperature or high humidity as it is a precise
optical component. Do not give a mechanical
shock to the CCD.
4) Do not expose the device to strong light. For
the color device, long exposure to strong light
will fade the color of the color filters.
– In case where the soldering may exceed the
time mentioned above, resume the work
after the device returns to normal
temperature.
ø Do not put too much force onto the lens and
the lens holder while soldering.
ø Be careful not to let the soldering iron touch
the lens holder.
– Soldering can be quickly/neatly done by
laying the soldering iron so it lightly touches
the border between the package and the
circuit board and sliding it in sideways.
14
Similar pages