Sanken M381L3223FTM-CLB3A2 184pin unbuffered module based on 256mb f-die with 64/72-bit non-ecc / ecc Datasheet

256MB, 512MB Unbuffered DIMM
DDR SDRAM
DDR SDRAM Unbuffered Module
184pin Unbuffered Module based on 256Mb F-die
with 64/72-bit Non-ECC / ECC
Revision 1.2
May. 2004
Rev. 1.2 May, 2004
256MB, 512MB Unbuffered DIMM
DDR SDRAM
Revision History
Revision 1.0 (August, 2003)
- First release
Revision 1.1 (August, 2003)
- Added K4H560838F based Module.
Revision 1.2 (May, 2004)
- Modified IDD current spec.
Rev. 1.2 May, 2004
256MB, 512MB Unbuffered DIMM
DDR SDRAM
184Pin Unbuffered DIMM based on 256Mb F-die (x8, x16)
Ordering Information
Part Number
Density
Organization
Component Composition
Height
M368L1624FTM-C(L)B3/AA/A2/B0
128MB
16M x 64
16Mx16 (K4H561638F) * 4EA
1,250mil
M368L3223FTN-C(L)B3/AA/A2/B0
256MB
32M x 64
32Mx8 (K4H560838F) * 8EA
1,250mil
M381L3223FTM-C(L)B3/AA/A2/B0
256MB
32M x 72
32Mx8 (K4H560838F) * 9EA
1,250mil
M368L6423FTN-C(L)B3/AA/A2/B0
512MB
64M x 64
32Mx8 (K4H560838F) * 16EA
1,250mil
M381L6423FTM-C(L)B3/AA/A2/B0
512MB
64M x 72
32Mx8 (K4H560838F) * 18EA
1,250mil
Operating Frequencies
B3(DDR333@CL=2.5)
AA(DDR266@CL=2)
A2(DDR266@CL=2)
B0(DDR266@CL=2.5)
Speed @CL2
133MHz
133MHz
133MHz
100MHz
Speed @CL2.5
166MHz
133MHz
133MHz
133MHz
CL-tRCD-tRP
2.5-3-3
2-2-2
2-3-3
2.5-3-3
Feature
• Power supply : Vdd: 2.5V ± 0.2V, Vddq: 2.5V ± 0.2V
• Double-data-rate architecture; two data transfers per clock cycle
• Bidirectional data strobe(DQS)
• Differential clock inputs(CK and CK)
• DLL aligns DQ and DQS transition with CK transition
• Programmable Read latency 2, 2.5 (clock)
• Programmable Burst length (2, 4, 8)
• Programmable Burst type (sequential & interleave)
• Edge aligned data output, center aligned data input
• Auto & Self refresh, 7.8us refresh interval(8K/64ms refresh)
• Serial presence detect with EEPROM
• PCB : Height 1,250 (mil), single (128MB, 256MB), double (512MB) sided
SAMSUNG ELECTRONICS CO., Ltd. reserves the right to change products and specifications without notice.
Rev. 1.2 May, 2004
256MB, 512MB Unbuffered DIMM
DDR SDRAM
Pin Configuration (Front side/back side)
Pin
Front
Pin
Front
Pin
Front
Pin
Back
Pin
Back
Pin
Back
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
VREF
DQ0
VSS
DQ1
DQS0
DQ2
VDD
DQ3
NC
NC
VSS
DQ8
DQ9
DQS1
VDDQ
CK1
/CK1
VSS
DQ10
DQ11
CKE0
VDDQ
DQ16
DQ17
DQS2
VSS
A9
DQ18
A7
VDDQ
DQ19
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
A5
DQ24
VSS
DQ25
DQS3
A4
VDD
DQ26
DQ27
A2
VSS
A1
CB0
CB1
VDD
DQS8
A0
CB2
VSS
CB3
BA1
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
VDDQ
/WE
DQ41
/CAS
VSS
DQS5
DQ42
DQ43
VDD
*/CS2
DQ48
DQ49
VSS
/CK2
CK2
VDDQ
DQS6
DQ50
DQ51
VSS
VDDID
DQ56
DQ57
VDD
DQS7
DQ58
DQ59
VSS
NC
SDA
SCL
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
VSS
DQ4
DQ5
VDDQ
DM0
DQ6
DQ7
VSS
NC
NC
NC
VDDQ
DQ12
DQ13
DM1
VDD
DQ14
DQ15
CKE1
VDDQ
*BA2
DQ20
A12
VSS
DQ21
A11
DM2
VDD
DQ22
A8
DQ23
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
VSS
A6
DQ28
DQ29
VDDQ
DM3
A3
DQ30
VSS
DQ31
CB4
CB5
VDDQ
CK0
/CK0
VSS
DM8
A10
CB6
VDDQ
CB7
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
/RAS
DQ45
VDDQ
/CS0
/CS1
DM5
VSS
DQ46
DQ47
*/CS3
VDDQ
DQ52
DQ53
*A13
VDD
DM6
DQ54
DQ55
VDDQ
NC
DQ60
DQ61
VSS
DM7
DQ62
DQ63
VDDQ
SA0
SA1
SA2
VDDSPD
KEY
53
54
55
56
57
58
59
60
61
DQ32
VDDQ
DQ33
DQS4
DQ34
VSS
BA0
DQ35
DQ40
KEY
145
146
147
148
149
150
151
152
153
VSS
DQ36
DQ37
VDD
DM4
DQ38
DQ39
VSS
DQ44
Note :
1. * : These pins are not used in this module.
2. Pins 44, 45, 47, 49, 51, 134, 135, 140, 142, 144 are used on x72(M381 ~ ) module, and are not used on x64(M368 ~ ) module.
3. Pins 111, 158 are NC for 1row modules [ M368L1624FTM, M368(81)L3223FTN(M)] & used for 2row modules
[M368(81)L6423FTN(M) ] .
Pin Description
Pin Name
Function
Pin Name
Function
A0 ~ A12
Address input (Multiplexed)
DM0 ~ 7, 8(for ECC)
Data - in mask
BA0 ~ BA1
Bank Select Address
VDD
Power supply (2.5V)
DQ0 ~ DQ63
Data input/output
VDDQ
Power Supply for DQS(2.5V)
DQS0 ~ DQS8
Data Strobe input/output
VSS
Ground
CK0,CK0 ~ CK2, CK2
Clock input
VREF
Power supply for reference
CKE0, CKE1(for double banks)
Clock enable input
VDDSPD
Serial EEPROM Power/Supply ( 2.3V to 3.6V )
CS0, CS1(for double banks)
Chip select input
SDA
Serial data I/O
RAS
Row address strobe
SCL
Serial clock
CAS
Column address strobe
SA0 ~ 2
Address in EEPROM
WE
Write enable
NC
No connection
CB0 ~ CB7 (for x72 module)
Check bit(Data-in/data-out)
Rev. 1.2 May, 2004
256MB, 512MB Unbuffered DIMM
DDR SDRAM
128MB, 16M x 64 Non ECC Module (M368L1624FTM) (Populated as 1 bank of x16 DDR SDRAM Module)
Functional Block Diagram
CS0
DQS1
DM1
LDQS
LDM
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
DQS0
DM0
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQS3
DM3
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
DQS2
DM2
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
I/O 6
I/O 4
I/O 1
I/O 3
I/O 2
I/O 0
I/O 5
I/O 7
UDQS
UDM
I/O 8
I/O 10
I/O 15
I/O 13
I/O 12
I/O 14
I/O 11
I/O 9
LDQS
LDM
I/O 6
I/O 4
I/O 1
I/O 3
I/O 2
I/O 0
I/O 5
I/O 7
UDQS
UDM
I/O 8
I/O 10
I/O 15
I/O 13
I/O 12
I/O 14
I/O 11
I/O 9
CS
DQS5
DM5
LDQS
LDM
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
D0
DQS4
DM4
CS
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
DQS7
DM7
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
D1
DQS6
DM6
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
I/O 6
I/O 4
I/O 1
I/O 3
I/O 2
I/O 0
I/O 5
I/O 7
UDQS
UDM
I/O 8
I/O 10
I/O 15
I/O 13
I/O 12
I/O 14
I/O 11
I/O 9
CS
D2
LDQS
LDM
I/O 6
I/O 4
I/O 1
I/O 3
I/O 2
I/O 0
I/O 5
I/O 7
UDQS
UDM
I/O 8
I/O 10
I/O 15
I/O 13
I/O 12
I/O 14
I/O 11
I/O 9
CS
D3
Cap/D0/*Cap
BA0 - BA1
BA0-BA1: DDR SDRAMs D0 - D3
A0 - A12
A0-A12: DDR SDRAMs D0 - D3
Cap/Cap/Cap
R=120Ω
CK0/1/2
RAS
RAS: DDR SDRAMs D0 - D3
CAS
CAS: DDR SDRAMs D0 - D3
CKE0
CKE: DDR SDRAMs D0 - D3
WE
WE: DDR SDRAMs D0 - D3
VDDSPD
VDD/VDDQ
CK0/1/2 Card
Edge
Clock Wiring
Clock
DDR SDRAMs
Input
SPD
D0 - D3
D0 - D3
VREF
D0 - D3
VSS
D0 - D3
Serial PD
SCL
SDA
WP
A0
A1
A2
SA0
SA1
SA2
Cap/Cap/Cap
Cap/D1/D3
0 DDR SDRAM
2 DDR SDRAMs
2 DDR SDRAMs
CK0/CK0
CK1/CK1
CK2/CK2
Cap/*Cap/D2
Cap/Cap/Cap
Notes:
1. DQ-to-I/O wiring is shown as recomended but
may be changed.
2. DQ/DQS/DM/CKE/CS relationships must be
maintained as shown.
3. DQ, DQS, DM/DQS resistors: 22 Ohms + 5%.
4. BAx, Ax, RAS, CAS, WE resistors: 7.5 Ohms
+ 5%
Rev. 1.2 May, 2004
256MB, 512MB Unbuffered DIMM
DDR SDRAM
256MB, 32M x 64 Non ECC Module (M368L3223FTN) (Populated as 1 bank of x8 DDR SDRAM Module)
Functional Block Diagram
CS0
DQS0
DM0
DQS4
DM4
DM/
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
CS
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DM/
DQS
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
D0
DQS1
DM1
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
Serial PD
SCL
D4
SDA
WP
A0
A1
A2
SA0
SA1
SA2
DQS5
DM5
DM/
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
CS
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DQS
DM/
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
D1
DQS2
DM2
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
D5
VDDSPD
SPD
VDD/VDDQ
D0 - D7
D0 - D7
VREF
D0 - D7
VSS
D0 - D7
DQS6
DM6
DM/
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
CS
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
D3/D0/D6
DQS
DM/
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
D2
DQS3
DM3
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
Cap/Cap/Cap
R=120Ω
D6
CK0/1/2
CK0/1/2 Card
Edge
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
BA0 - BA1
A0 - A12
CS
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DM/
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
A0-A12 : DDR SDRAMs D0 - D7
RAS : DDR SDRAMs D0 - D7
CAS
CAS : DDR SDRAMs D0 - D7
CKE0
CKE : DDR SDRAMs D0 - D7
WE : DDR SDRAMs D0 - D7
CS
DQS
D7
* Clock Wiring
BA0-BA1 : DDR SDRAMs D0 - D7
RAS
WE
Cap/Cap/Cap
DQS
D3
Cap/Cap/Cap
D5/D2/Cap
DQS7
DM7
DM/
D4/D1/D7
Clock
Input
DDR SDRAMs
*CK0/CK0
*CK1/CK1
*CK2/CK2
3 DDR SDRAMs
3 DDR SDRAMs
2 DDR SDRAMs
Notes :
1. DQ-to-I/O wiring is shown as recommended
but may be changed.
2. DQ/DQS/DM/CKE/CS relationships must be
maintained as shown.
3. DQ, DQS, DM/DQS resistors: 22 Ohms + 5%.
4. BAx, Ax, RAS, CAS, WE resistors: 5.1 Ohms +
5%
*Clock Net Wiring
Rev. 1.2 May, 2004
256MB, 512MB Unbuffered DIMM
DDR SDRAM
256MB, 32M x 72 ECC Module (M381L3223FTM) (Populated as 1 bank of x8 DDR SDRAM Module)
Functional Block Diagram
CS0
DQS0
DM0
DQS4
DM4
DM/
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
CS
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DM/
DQS
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
D0
DQS1
DM1
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
Serial PD
D4
SCL
SDA
WP
A0
A1
A2
SA0
SA1
SA2
DQS5
DM5
DM/
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
CS
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DQS
DM/
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
D1
DQS2
DM2
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
D5
VDDSPD
SPD
VDD/VDDQ
D0 - D8
D0 - D8
VREF
D0 - D8
VSS
D0 - D8
DQS6
DM6
DM/
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
CS
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
D3/D0/D6
DQS
DM/
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
D2
DQS3
DM3
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
Cap/Cap/Cap
R=120Ω
D6
CK0/1/2
CK0/1/2 Card
Edge
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
CS
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
Cap/Cap/Cap
DQS
DM/
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
D3
Cap/Cap/Cap
D5/D2/D8
DQS7
DM7
DM/
D4/D1/D7
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
D7
DQS8
DM8
DM/
CB0
CB1
CB2
CB3
CB4
CB5
CB6
CB7
BA0 - BA1
A0 - A12
CS
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DQS
D8
BA0-BA1 : DDR SDRAMs D0 - D8
RAS
RAS : DDR SDRAMs D0 - D8
CAS
CAS : DDR SDRAMs D0 - D8
CKE0
CKE : DDR SDRAMs D0 - D8
WE
* Clock Wiring
A0-A12 : DDR SDRAMs D0 - D8
Clock
Input
DDR SDRAMs
*CK0/CK0
*CK1/CK1
*CK2/CK2
3 DDR SDRAMs
3 DDR SDRAMs
3 DDR SDRAMs
Notes :
1. DQ-to-I/O wiring is shown as recommended
but may be changed.
2. DQ/DQS/DM/CKE/CS relationships must be
maintained as shown.
3. DQ, DQS, DM/DQS resistors: 22 Ohms + 5%.
4. BAx, Ax, RAS, CAS, WE resistors: 5.1 Ohms +
5%
WE : DDR SDRAMs D0 - D8
*Clock Net Wiring
Rev. 1.2 May, 2004
256MB, 512MB Unbuffered DIMM
DDR SDRAM
512MB, 64M x 64 Non ECC Module (M368L6423FTN) (Populated as 2 bank of x8 DDR SDRAM Module)
Functional Block Diagram
CS1
CS0
DQS0
DM0
DQS4
DM4
DM/
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
DM/
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
D0
CS
DQS
DM/
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
D8
DQS1
DM1
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
DM/
CS
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
D4
DQS
D12
DQS5
DM5
DM/
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
DM/
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
D1
CS
DQS
DM/
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
D9
DQS2
DM2
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
DM/
CS
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
D5
DQS
D13
DQS6
DM6
DM/
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
DM/
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
D2
CS
DQS
DM/
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
D10
DQS3
DM3
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
DM/
CS
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
D6
DQS
D14
DQS7
DM7
DM/
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
D3
DM/
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
CS
DM/
DQS
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
D11
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
DM/
CS
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
D7
DQS
D15
D3/D0/D5
VDDSPD
SPD
VDD/VDDQ
D0 - D15
D11/D8/D13
Serial PD
SCL
D0 - D15
CK0/1/2
VREF
D0 - D15
VSS
D0 - D15
CK0/1/2 Card
Edge
SDA
WP
A0
A1
A2
SA0
SA1
SA2
R=120Ω
*Cap/D1/D6
*Cap/D9/D14
D4/D2/D7
D12/D10/D15
BA0 - BA1
BA0-BA1 : DDR SDRAMs D0 - D15
* Clock Wiring
A0 - A12
RAS
A0-A12: DDR SDRAMs D0 - D15
RAS : DDR SDRAMs D0 - D15
CAS
CAS : DDR SDRAMs D0 - D15
CKE 0/1
CKE : DDR SDRAMs D0 - D15
WE
WE : DDR SDRAMs D0 - D15
Clock
Input
DDR SDRAMs
*CK0/CK0
*CK1/CK1
*CK2/CK2
4 DDR SDRAMs
6 DDR SDRAMs
6 DDR SDRAMs
Notes :
1. DQ-to-I/O wiring is shown as recommended
but may be changed.
2. DQ/DQS/DM/CKE/CS relationships must be
maintained as shown.
3. DQ, DQS, DM/DQS resistors: 22 Ohms + 5%.
4. BAx, Ax, RAS, CAS, WE resistors: 3 Ohms +
5%
*Clock Net Wiring
Rev. 1.2 May, 2004
256MB, 512MB Unbuffered DIMM
DDR SDRAM
512MB, 64M x 72 ECC Module (M381L6423FTM) (Populated as 2 bank of x8 DDR SDRAM Module)
Functional Block Diagram
CS1
CS0
DQS0
DM0
DQS4
DM4
DM/
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
CS
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DM/
DQS
CS
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
D0
DQS
DM/
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
D9
DQS1
DM1
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
DM/
CS
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
D4
DQS
D13
DQS5
DM5
DM/
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
CS
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DQS
DM/
CS
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
D1
DQS
DM/
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
D10
DQS2
DM2
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
DM/
CS
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
D5
DQS
D14
DQS6
DM6
DM/
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
CS
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DQS
DM/
CS
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
D2
DQS
DM/
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
D11
DQS3
DM3
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
DM/
CS
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
D6
DQS
D15
DQS7
DM7
DM/
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
CS
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DQS
DM/
CS
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
D3
DM/
DQS
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
D12
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
DM/
CS
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
D7
DQS
D16
DQS8
DM8
D3/D0/D5
DM/
CS
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CB0
CB1
CB2
CB3
CB4
CB5
CB6
CB7
DQS
DM/
CS
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
D8
DQS
CK0/1/2 Card
Edge
SCL
SDA
A0
SA0
BA0 - BA1
A1
SA1
R=120Ω
CK0/1/2
Serial PD
WP
D12/D9/D14
D17
VDDSPD
SPD
VDD/VDDQ
D0 - D17
D0 - D17
A2
VREF
D0 - D17
VSS
D0 - D17
SA2
BA0-BA1 : DDR SDRAMs D0 - D17
* Clock Wiring
A0 - A12
A0-A12 : DDR SDRAMs D0 - D17
RAS
RAS : DDR SDRAMs D0 - D17
CAS
CAS : DDR SDRAMs D0 - D17
CKE0/1
CKE : DDR SDRAMs D0 - D17
WE
WE : DDR SDRAMs D0 - D17
Clock
Input
DDR SDRAMs
*CK0/CK0
*CK1/CK1
*CK2/CK2
6 DDR SDRAMs
6 DDR SDRAMs
6 DDR SDRAMs
D8/D1/D6
D17/D10/D15
D4/D2/D7
D13/D11/D16
Notes :
1. DQ-to-I/O wiring is shown as recommended
but may be changed.
2. DQ/DQS/DM/CKE/CS relationships must be
maintained as shown.
3. DQ, DQS, DM/DQS resistors: 22 Ohms + 5%.
4. BAx, Ax, RAS, CAS, WE resistors:3 Ohms +
5%
*Clock Net Wiring
Rev. 1.2 May, 2004
256MB, 512MB Unbuffered DIMM
DDR SDRAM
Absolute Maximum Ratings
Parameter
Symbol
Value
Unit
Voltage on any pin relative to VSS
VIN, VOUT
-0.5 ~ 3.6
V
Voltage on VDD & VDDQ supply relative to VSS
VDD, VDDQ
-1.0 ~ 3.6
V
Storage temperature
TSTG
-55 ~ +150
°C
Power dissipation
PD
1.5 * # of component
W
Short circuit current
IOS
50
mA
Note : Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded.
Functional operation should be restricted to recommend operation condition.
Exposure to higher than recommended voltage for extended periods of time could affect device reliability.
DC Operating Conditions
Recommended operating conditions(Voltage referenced to VSS=0V, TA=0 to 70°C)
Symbol
Min
Supply voltage(for device with a nominal VDD of 2.5V)
Parameter
VDD
2.3
Max
Unit
2.7
I/O Supply voltage
VDDQ
2.3
2.7
V
I/O Reference voltage
VREF
0.49*VDDQ
0.51*VDDQ
V
1
I/O Termination voltage(system)
VTT
VREF-0.04
VREF+0.04
V
2
V
Input logic high voltage
VIH(DC)
VREF+0.15
VDDQ+0.3
Input logic low voltage
VIL(DC)
-0.3
VREF-0.15
V
Input Voltage Level, CK and CK inputs
VIN(DC)
-0.3
VDDQ+0.3
V
Note
Input Differential Voltage, CK and CK inputs
VID(DC)
0.36
VDDQ+0.6
V
3
V-I Matching: Pullup to Pulldown Current Ratio
VI(Ratio)
0.71
1.4
-
4
II
-2
2
uA
Output leakage current
IOZ
-5
5
uA
Output High Current(Normal strengh driver) ;VOUT = VTT + 0.84V
IOH
-16.8
mA
Output High Current(Normal strengh driver) ;VOUT = VTT - 0.84V
IOL
16.8
mA
Output High Current(Half strengh driver) ;VOUT = VTT + 0.45V
IOH
-9
mA
Output High Current(Half strengh driver) ;VOUT = VTT - 0.45V
IOL
9
mA
Input leakage current
Note : 1.VREF is expected to be equal to 0.5*VDDQ of the transmitting device, and to track variations in the dc level of same.
Peak-to peak noise on VREF may not exceed +/-2% of the dc value.
2. VTT is not applied directly to the device. VTT is a system supply for signal termination resistors, is expected to be set equal to
VREF, and must track variations in the DC level of VREF
3. VID is the magnitude of the difference between the input level on CK and the input level on CK.
4. The ratio of the pullup current to the pulldown current is specified for the same temperature and voltage, over the entire
temperature and voltage range, for device drain to source voltages from 0.25V to 1.0V. For a given output, it represents the
maximum difference between pullup and pulldown drivers due to process variation. The full variation in the ratio of the
maximum to minimum pullup and pulldown current will not exceed 1/7 for device drain to source voltages from 0.1 to 1.0.
Rev. 1.2 May, 2004
256MB, 512MB Unbuffered DIMM
DDR SDRAM
DDR SDRAM IDD spec table
M368L1624FTM [ (16M x 16) * 4, 128MB Non ECC Module ]
Symbol
IDD6
B3(DDR333@CL=2.5) AA(DDR266@CL=2)
(VDD=2.7V, T = 10°C)
A2(DDR266@CL=2) B0(DDR266@CL=2.5)
Unit
IDD0
360
320
320
320
IDD1
500
460
460
460
mA
IDD2P
12
12
12
12
mA
mA
IDD2F
100
80
80
80
mA
IDD2Q
80
72
72
72
mA
IDD3P
140
120
120
120
mA
IDD3N
220
180
180
180
mA
IDD4R
800
680
680
680
mA
IDD4W
760
620
620
620
mA
IDD5
720
660
660
660
mA
12
12
12
12
mA
Normal
Low power
IDD7A
Notes
6
6
6
6
mA
1,400
1,200
1,200
1,200
mA
Optional
* Module IDD was calculated on the basis of component IDD and can be differently measured according to DQ loading cap.
Rev. 1.2 May, 2004
256MB, 512MB Unbuffered DIMM
DDR SDRAM
DDR SDRAM IDD spec table
M368L3223FTN [ (32M x 8) * 8, 256MB Non ECC Module ]
Symbol
IDD6
(VDD=2.7V, T = 10°C)
B3(DDR333@CL=2.5) AA(DDR266@CL=2) A2(DDR266@CL=2) B0(DDR266@CL=2.5)
IDD0
720
720
640
640
Unit
IDD1
920
920
840
840
mA
IDD2P
24
24
24
24
mA
mA
IDD2F
240
200
200
200
IDD2Q
200
185
185
185
mA
IDD3P
280
240
240
240
mA
IDD3N
440
360
360
360
mA
mA
IDD4R
1,280
1,120
1,120
1,120
IDD4W
1,280
1,080
1,080
1,080
mA
IDD5
1,360
1,280
1,280
1,280
mA
Normal
24
24
24
24
mA
Low power
12
12
12
12
mA
2,240
2,240
2,080
2,080
mA
IDD7A
Notes
mA
Optional
* Module IDD was calculated on the basis of component IDD and can be differently measured according to DQ loading cap.
M381L3223FTM [ (32M x 8) * 9, 256MB ECC Module ]
Symbol
IDD6
(VDD=2.7V, T = 10°C)
B3(DDR333@CL=2.5) AA(DDR266@CL=2) A2(DDR266@CL=2) B0(DDR266@CL=2.5)
Unit
IDD0
810
810
720
720
mA
IDD1
1,035
1,035
950
950
mA
IDD2P
27
27
27
27
mA
IDD2F
270
225
225
225
mA
IDD2Q
225
210
210
210
mA
IDD3P
320
270
270
270
mA
IDD3N
500
410
410
410
mA
IDD4R
1,440
1260
1260
1,260
mA
IDD4W
1,440
1,220
1,220
1,220
mA
IDD5
1,530
1,440
1,440
1,440
mA
Normal
27
27
27
27
mA
Low power
14
14
14
14
mA
2,520
2,520
2,340
2,340
mA
IDD7A
Notes
Optional
* Module IDD was calculated on the basis of component IDD and can be differently measured according to DQ loading cap.
Rev. 1.2 May, 2004
256MB, 512MB Unbuffered DIMM
DDR SDRAM
DDR SDRAM IDD spec table
M368L6423FTN [ (32M x 8) * 16, 512MB Non ECC Module ]
Symbol
IDD6
B3(DDR333@CL=2.5) AA(DDR266@CL=2)
(VDD=2.7V, T = 10°C)
A2(DDR266@CL=2) B0(DDR266@CL=2.5)
Unit
IDD0
1,160
1,080
1,000
1,000
mA
IDD1
1,360
1,280
1,200
1,200
mA
IDD2P
48
48
48
48
mA
mA
IDD2F
480
400
400
400
IDD2Q
320
290
290
290
mA
IDD3P
560
480
480
480
mA
IDD3N
880
720
720
720
mA
mA
IDD4R
1,720
1,480
1,480
1,480
IDD4W
1,720
1,440
1,440
1,440
mA
IDD5
1,800
1,640
1,640
1,640
mA
Normal
48
48
48
48
mA
Low power
24
24
24
24
mA
2,680
2,600
2,440
2,440
mA
IDD7A
Notes
Optional
* Module IDD was calculated on the basis of component IDD and can be differently measured according to DQ loading cap.
M381L6423FTM [ (32M x 8) * 18, 512MB ECC Module ]
Symbol
IDD6
(VDD=2.7V, T = 10°C)
B3(DDR333@CL=2.5) AA(DDR266@CL=2) A2 (DDR266@CL=2) B0(DDR266@CL=2.5)
Unit
IDD0
1,310
1,220
1,130
1,130
mA
IDD1
1,530
1,440
1,350
1,350
mA
IDD2P
54
54
54
54
mA
IDD2F
540
450
450
450
mA
IDD2Q
450
420
420
420
mA
IDD3P
630
540
540
540
mA
IDD3N
990
810
810
810
mA
IDD4R
1,940
1,670
1,670
1,670
mA
IDD4W
1,940
1,620
1,620
1,620
mA
IDD5
2,030
1,850
1,850
1,850
mA
Normal
54
54
54
54
mA
Low power
27
27
27
27
mA
3,020
2,930
2,750
2,750
mA
IDD7A
Notes
Optional
* Module IDD was calculated on the basis of component IDD and can be differently measured according to DQ loading cap.
Rev. 1.2 May, 2004
256MB, 512MB Unbuffered DIMM
DDR SDRAM
AC Operating Conditions
Parameter/Condition
Max
Symbol
Min
Input High (Logic 1) Voltage, DQ, DQS and DM signals
VIH(AC)
VREF + 0.31
Input Low (Logic 0) Voltage, DQ, DQS and DM signals.
VIL(AC)
Input Differential Voltage, CK and CK inputs
VID(AC)
0.7
Input Crossing Point Voltage, CK and CK inputs
VIX(AC)
0.5*VDDQ-0.2
Unit
Note
V
3
VREF - 0.31
V
3
VDDQ+0.6
V
1
0.5*VDDQ+0.2
V
2
Note : 1. VID is the magnitude of the difference between the input level on CK and the input on CK.
2. The value of VIX is expected to equal 0.5*VDDQ of the transmitting device and must track variations in the DC level of the same.
3. These parameters should be tested at the pim on actual components and may be checked at either the pin or the pad in
simulation. the AC and DC input specificatims are refation to a Vref envelope that has been bandwidth limited 20MHz.
Vtt=0.5*VDDQ
RT=50Ω
Output
Z0=50Ω
VREF
=0.5*VDDQ
CLOAD=30pF
Output Load Circuit (SSTL_2)
Input/Output Capacitance
Parameter
(VDD=2.5V, VDDQ=2.5V, TA= 25°C, f=1MHz)
Symbol
M368L1624FTM
M368L3223FTN
M381L3223FTM
Unit
Min
Max
Min
Max
Min
Max
CIN1
41
45
49
57
51
60
pF
Input capacitance(CKE0)
CIN2
34
38
42
50
44
53
pF
Input capacitance( CS0)
CIN3
34
38
42
50
44
53
pF
Input capacitance( CLK0, CLK1,CLK2)
CIN4
25
30
25
30
25
30
pF
Input capacitance(DM0~DM7, DM8 (for ECC))
CIN5
6
7
6
7
6
7
pF
Data & DQS input/output capacitance(DQ0~DQ63)
Cout1
6
7
6
7
6
7
pF
Data input/output capacitance (CB0~CB7)
Cout2
-
-
-
-
6
7
pF
Input capacitance(A0 ~ A12, BA0 ~ BA1,RAS,CAS,WE )
Parameter
Symbol
M368L6423FTN
Min
Max
M381L6423FTM
Min
Max
Unit
Input capacitance(A0 ~ A12, BA0 ~ BA1,RAS,CAS,WE )
CIN1
65
81
69
87
pF
Input capacitance(CKE0,CKE1)
CIN2
42
50
44
53
pF
Input capacitance( CS0, CS1)
CIN3
42
50
44
53
pF
Input capacitance( CLK0, CLK1,CLK2)
CIN4
28
34
28
34
pF
Input capacitance(DM0~DM7, DM8 (for ECC))
CIN5
10
12
10
12
pF
Data & DQS input/output capacitance(DQ0~DQ63)
Cout1
10
12
10
12
pF
Data input/output capacitance (CB0~CB7)
Cout2
-
-
10
12
pF
Rev. 1.2 May, 2004
256MB, 512MB Unbuffered DIMM
DDR SDRAM
AC Timming Parameters & Specifications
Parameter
Symbol
B3
AA
(DDR333@CL=2.5) (DDR266@CL=2.0
Min
Max
B0
A2
(DDR266@CL=2.0) (DDR266@CL=2.5)
Min
Max
Min
Unit
Row cycle time
tRC
60
60
65
65
ns
Refresh row cycle time
tRFC
72
75
75
75
ns
Row active time
tRAS
42
RAS to CAS delay
tRCD
18
15
20
20
ns
ns
Row precharge time
70K
45
120K
45
120K
45
120K
ns
tRP
18
15
20
20
Row active to Row active delay
tRRD
12
15
15
15
ns
Write recovery time
tWR
15
15
15
15
ns
Last data in to Read command
tWTR
1
1
1
1
tCK
Col. address to Col. address delay
tCCD
1
1
1
1
Clock cycle time
CL=2.0
CL=2.5
Clock high level width
Clock low level width
tCK
7.5
12
7.5
12
7.5
12
10
tCK
12
ns
6
12
7.5
12
7.5
12
7.5
12
ns
tCH
0.45
0.55
0.45
0.55
0.45
0.55
0.45
0.55
tCK
tCK
tCL
0.45
0.55
0.45
0.55
0.45
0.55
0.45
0.55
tDQSCK
-0.6
+0.6
-0.75
+0.75
-0.75
+0.75
-0.75
+0.75
ns
Output data access time from CK/CK
tAC
-0.7
+0.7
-0.75
+0.75
-0.75
+0.75
-0.75
+0.75
ns
Data strobe edge to ouput data edge
tDQSQ
-
0.45
-
0.5
-
0.5
-
0.5
ns
Read Preamble
tRPRE
0.9
1.1
0.9
1.1
0.9
1.1
0.9
1.1
tCK
DQS-out access time from CK/CK
Read Postamble
tRPST
0.4
0.6
0.4
0.6
0.4
0.6
0.4
0.6
tCK
CK to valid DQS-in
tDQSS
0.75
1.25
0.75
1.25
0.75
1.25
0.75
1.25
tCK
DQS-in setup time
tWPRES
0
0
0
0
ns
DQS-in hold time
tWPRE
0.25
0.25
0.25
0.25
tCK
DQS falling edge to CK rising-setup time
tDSS
0.2
0.2
0.2
0.2
tCK
DQS falling edge from CK rising-hold time
tDSH
0.2
0.2
0.2
0.2
tCK
DQS-in high level width
tDQSH
0.35
0.35
0.35
0.35
tCK
DQS-in low level width
tDQSL
0.35
DQS-in cycle time
tDSC
0.9
0.35
1.1
0.9
0.35
1.1
0.9
0.35
1.1
0.9
Note
Max
12
3
tCK
1.1
tCK
Address and Control Input setup time(fast)
tIS
0.75
0.9
0.9
0.9
ns
i,5.7~9
Address and Control Input hold time(fast)
tIH
0.75
0.9
0.9
0.9
ns
i,5.7~9
Address and Control Input setup time(slow)
tIS
0.8
1.0
1.0
1.0
ns
i, 6~9
Address and Control Input hold time(slow)
tIH
0.8
1.0
1.0
1.0
ns
i, 6~9
Data-out high impedence time from CK/CK
tHZ
+0.75
ns
1
Data-out low impedence time from CK/CK
tLZ
-0.7
+0.7
-0.75
+0.75
-0.75
+0.75
-0.75
+0.75
ns
1
tSLMR
0.67
1.5
0.67
1.5
0.67
1.5
0.67
1.5
Output Slew Rate Matching Ratio(rise to fall)
+0.7
+0.75
+0.75
Rev. 1.2 May, 2004
256MB, 512MB Unbuffered DIMM
Parameter
Symbol
DDR SDRAM
B3
AA
(DDR333@CL=2.5)) (DDR266@CL=2.0)
Min
A2
B0
(DDR266@CL=2.0) (DDR266@CL=2.5))
Max
Min
Max
Min
Unit
Note
Max
Mode register set cycle time
tMRD
12
15
15
15
ns
DQ & DM setup time to DQS
tDS
0.45
0.5
0.5
0.5
ns
j, k
DQ & DM hold time to DQS
tDH
0.45
0.5
0.5
0.5
ns
j, k
Control & Address input pulse width
tIPW
2.2
2.2
2.2
2.2
ns
8
DQ & DM input pulse width
tDIPW
1.75
1.75
1.75
1.75
ns
8
Power down exit time
tPDEX
6
7.5
7.5
7.5
ns
Exit self refresh to non-Read command
tXSNR
75
75
75
75
ns
Exit self refresh to read command
tXSRD
200
200
200
200
tCK
Refresh interval time
tREFI
7.8
Output DQS valid window
tQH
tHP
-tQHS
Clock half period
tHP
tCLmin
or tCHmin
7.8
-
tHP
-tQHS
-
tCLmin
or tCHmin
-
tCLmin
or tCHmin
us
4
-
-
ns
11
-
tCLmin
or tCHmin
-
ns
10, 11
0.75
ns
11
0.6
tCK
2
tCK
13
tQHS
DQS write postamble time
tWPST
0.4
tRAP
18
20
20
20
tDAL
(tWR/tCK)
+
(tRP/tCK)
(tWR/tCK)
+
(tRP/tCK)
(tWR/tCK)
+
(tRP/tCK)
(tWR/tCK)
+
(tRP/tCK)
Autoprecharge write recovery +
Precharge time
0.75
7.8
tHP
-tQHS
Data hold skew factor
Active to Read with Auto precharge
command
0.55
7.8
tHP
-tQHS
0.6
0.4
0.75
0.6
0.4
0.6
0.4
System Characteristics for DDR SDRAM
The following specification parameters are required in systems using DDR333& DDR266 devices to ensure proper system
performance. these characteristics are for system simulation purposes and are guaranteed by design.
Table 1 : Input Slew Rate for DQ, DQS, and DM
AC CHARACTERISTICS
DDR333
DDR266
PARAMETER
SYMBOL
MIN
MAX
MIN
MAX
Units
Notes
DQ/DM/DQS input slew rate measured between
VIH(DC), VIL(DC) and VIL(DC), VIH(DC)
DCSLEW
TBD
TBD
TBD
TBD
V/ns
a, m
Table 2 : Input Setup & Hold Time Derating for Slew Rate
Input Slew Rate
tIS
tIH
Units
Notes
0.5 V/ns
0
0
ps
i
0.4 V/ns
+50
0
ps
i
0.3 V/ns
+100
0
ps
i
Table 3 : Input/Output Setup & Hold Time Derating for Slew Rate
Input Slew Rate
tDS
tDH
Units
0.5 V/ns
0
0
ps
Notes
k
0.4 V/ns
+75
+75
ps
k
0.3 V/ns
+150
+150
ps
k
Rev. 1.2 May, 2004
256MB, 512MB Unbuffered DIMM
DDR SDRAM
Table 4 : Input/Output Setup & Hold Derating for Rise/Fall Delta Slew Rate
Delta Slew Rate
tDS
tDH
Units
Notes
+/- 0.0 V/ns
0
0
ps
j
+/- 0.25 V/ns
+50
+50
ps
j
+/- 0.5 V/ns
+100
+100
ps
j
Table 5 : Output Slew Rate Characteristice (X4, X8 Devices only)
Slew Rate Characteristic
Typical Range
(V/ns)
Minimum
(V/ns)
Maximum
(V/ns)
Notes
Pullup Slew Rate
1.2 ~ 2.5
1.0
4.5
a,c,d,f,g,h
Pulldown slew
1.2 ~ 2.5
1.0
4.5
b,c,d,f,g,h
Table 6 : Output Slew Rate Characteristice (X16 Devices only)
Slew Rate Characteristic
Typical Range
(V/ns)
Minimum
(V/ns)
Maximum
(V/ns)
Notes
Pullup Slew Rate
1.2 ~ 2.5
0.7
5.0
a,c,d,f,g,h
Pulldown slew
1.2 ~ 2.5
0.7
5.0
b,c,d,f,g,h
Table 7 : Output Slew Rate Matching Ratio Characteristics
AC CHARACTERISTICS
DDR333
DDR266
PARAMETER
MIN
MAX
MIN
MAX
Notes
Output Slew Rate Matching Ratio (Pullup to Pulldown)
TBD
TBD
TBD
TBD
e,m
Rev. 1.2 May, 2004
256MB, 512MB Unbuffered DIMM
DDR SDRAM
Component Notes
1. tHZ and tLZ transitions occur in the same access time windows as valid data transitions. these parameters are not referenced to a
specific voltage level but specify when the device output in no longer driving (HZ), or begins driving (LZ).
2. The maximum limit for this parameter is not a device limit. The device will operate with a greater value for this parameter, but sys
tem performance (bus turnaround) will degrade accordingly.
3. The specific requirement is that DQS be valid (HIGH, LOW, or at some point on a valid transition) on or before this CK edge. A
valid transition is defined as monotonic and meeting the input slew rate specifications of the device. when no writes were previ
ously in progress on the bus, DQS will be tran sitioning from High- Z to logic LOW. If a previous write was in progress, DQS could
be HIGH, LOW, or transitioning from HIGH to LOW at this time, depending on tDQSS.
4. A maximum of eight AUTO REFRESH commands can be posted to any given DDR SDRAM device.
5. For command/address input slew rate ≥ 1.0 V/ns
6. For command/address input slew rate ≥ 0.5 V/ns and < 1.0 V/ns
7. For CK & CK slew rate ≥ 1.0 V/ns
8. These parameters guarantee device timing, but they are not necessarily tested on each device. They may be guaranteed by
device design or tester correlation.
9. Slew Rate is measured between VOH(ac) and VOL(ac).
10. Min (tCL, tCH) refers to the smaller of the actual clock low time and the actual clock high time as provided to the device (i.e. this
value can be greater than the minimum specification limits for tCL and tCH).....For example, tCL and tCH are = 50% of the
period, less the half period jitter (tJIT(HP)) of the clock source, and less the half period jitter due to crosstalk (tJIT(crosstalk)) into
the clock traces.
11. tQH = tHP - tQHS, where:
tHP = minimum half clock period for any given cycle and is defined by clock high or clock low (tCH, tCL). tQHS accounts for 1) The
pulse duration distortion of on-chip clock circuits; and 2) The worst case push-out of DQS on one tansition followed by the worst
case pull-in of DQ on the next transition, both of which are, separately, due to data pin skew and output pattern effects, and pchannel to n-channel variation of the output drivers.
12. tDQSQ
Consists of data pin skew and output pattern effects, and p-channel to n-channel variation of the output drivers for any given
cycle.
13. tDAL = (tWR/tCK) + (tRP/tCK)
For each of the terms above, if not already an integer, round to the next highest integer. Example: For DDR266B at CL=2.5 and
tCK=7.5ns tDAL = (15 ns / 7.5 ns) + (20 ns/ 7.5ns) = (2) + (3)
tDAL = 5 clocks
Rev. 1.2 May, 2004
256MB, 512MB Unbuffered DIMM
DDR SDRAM
System Notes :
a. Pullup slew rate is characteristized under the test conditions as shown in Figure 1.
Test point
Output
50Ω
VSSQ
Figure 1 : Pullup slew rate test load
b. Pulldown slew rate is measured under the test conditions shown in Figure 2.
VDDQ
50Ω
Output
Test point
Figure 2 : Pulldown slew rate test load
c. Pullup slew rate is measured between (VDDQ/2 - 320 mV +/- 250 mV)
Pulldown slew rate is measured between (VDDQ/2 + 320 mV +/- 250 mV)
Pullup and Pulldown slew rate conditions are to be met for any pattern of data, including all outputs switching and only one output
switching.
Example : For typical slew rate, DQ0 is switching
For minmum slew rate, all DQ bits are switching from either high to low, or low to high.
The remaining DQ bits remain the same as for previous state.
d. Evaluation conditions
Typical : 25 °C (T Ambient), VDDQ = 2.5V, typical process
Minimum : 70 °C (T Ambient), VDDQ = 2.3V, slow - slow process
Maximum : 0 °C (T Ambient), VDDQ = 2.7V, fast - fast process
e. The ratio of pullup slew rate to pulldown slew rate is specified for the same temperature and voltage, over the entire temperature and
voltage range. For a given output, it represents the maximum difference between pullup and pulldown drivers due to process variation.
f. Verified under typical conditions for qualification purposes.
g. TSOPII package divices only.
h. Only intended for operation up to 266 Mbps per pin.
i. A derating factor will be used to increase tIS and tIH in the case where the input slew rate is below 0.5V/ns
as shown in Table 2. The Input slew rate is based on the lesser of the slew rates detemined by either VIH(AC) to VIL(AC) or
VIH(DC) to VIL(DC), similarly for rising transitions.
j. A derating factor will be used to increase tDS and tDH in the case where DQ, DM, and DQS slew rates differ, as shown in Tables 3 & 4.
Input slew rate is based on the larger of AC-AC delta rise, fall rate and DC-DC delta rise, Input slew rate is based on the lesser of the
slew rates determined by either VIH(AC) to VIL(AC) or VIH(DC) to VIL(DC), similarly for rising transitions.
The delta rise/fall rate is calculated as: {1/(Slew Rate1)} - {1/(Slew Rate2)}
For example : If Slew Rate 1 is 0.5 V/ns and slew Rate 2 is 0.4 V/ns, then the delta rise, fall rate is - 0.5ns/V . Using the table given, this
would result in the need for an increase in tDS and tDH of 100 ps.
k. Table 3 is used to increase tDS and tDH in the case where the I/O slew rate is below 0.5 V/ns. The I/O slew rate is based on the lesser
on the lesser of the AC - AC slew rate and the DC- DC slew rate. The inut slew rate is based on the lesser of the slew rates deter
mined by either VIH(ac) to VIL(ac) or VIH(DC) to VIL(DC), and similarly for rising transitions.
m. DQS, DM, and DQ input slew rate is specified to prevent double clocking of data and preserve setup and hold times. Signal transi
tions through the DC region must be monotony.
Rev. 1.2 May, 2004
256MB, 512MB Unbuffered DIMM
DDR SDRAM
Command Truth Table
(V=Valid, X=Don′t Care, H=Logic High, L=Logic Low)
COMMAND
CKEn-1
CKEn
CS
RAS
CAS
WE BA0,1 A10/AP
A0 ~ A9
A11, A12
Note
Register
Extended MRS
H
X
L
L
L
L
OP CODE
1, 2
Register
Mode Register Set
H
X
L
L
L
L
OP CODE
1, 2
L
L
L
H
X
L
H
H
H
Auto Refresh
Refresh
Entry
Self
Refresh
Exit
H
H
L
L
H
H
X
X
X
Bank Active & Row Addr.
H
X
L
L
H
H
V
Read &
Column Address
Auto Precharge Disable
H
X
L
H
L
H
V
Write &
Column Address
Auto Precharge Disable
Auto Precharge Enable
Auto Precharge Enable
Burst Stop
Precharge
Bank Selection
X
L
H
L
L
H
X
L
H
H
L
H
All Banks
Active Power Down
H
X
Entry
H
L
Exit
L
H
Entry
H
L
Precharge Power Down Mode
Exit
DM
No operation (NOP) : Not defined
L
H
L
L
H
L
H
X
X
X
L
V
V
V
X
X
X
X
H
X
X
X
L
H
H
H
H
X
X
X
L
V
V
V
H
H
X
X
X
X
X
L
H
H
H
3
3
X
V
3
Row Address
L
Column
Address
H
L
Column
Address
H
X
V
L
X
H
4
4
4
4, 6
7
X
5
X
X
X
H
3
X
8
9
9
Note : 1. OP Code : Operand Code. A0 ~ A12 & BA0 ~ BA1 : Program keys. (@EMRS/MRS)
2. EMRS/ MRS can be issued only at all banks precharge state.
A new command can be issued 2 clock cycles after EMRS or MRS.
3. Auto refresh functions are same as the CBR refresh of DRAM.
The automatical precharge without row precharge command is meant by "Auto".
Auto/self refresh can be issued only at all banks precharge state.
4. BA0 ~ BA1 : Bank select addresses.
If both BA0 and BA1 are "Low" at read, write, row active and precharge, bank A is selected.
If BA0 is "High" and BA1 is "Low" at read, write, row active and precharge, bank B is selected.
If BA0 is "Low" and BA1 is "High" at read, write, row active and precharge, bank C is selected.
If both BA0 and BA1 are "High" at read, write, row active and precharge, bank D is selected.
5. If A10/AP is "High" at row precharge, BA0 and BA1 are ignored and all banks are selected.
6. During burst write with auto precharge, new read/write command can not be issued.
Another bank read/write command can be issued after the end of burst.
New row active of the associated bank can be issued at tRP after the end of burst.
7. Burst stop command is valid at every burst length.
8. DM sampled at the rising and falling edges of the DQS and Data-in are masked at the both edges (Write DM latency is 0).
9. This combination is not defined for any function, which means "No Operation(NOP)" in DDR SDRAM.
Rev. 1.2 May, 2004
256MB, 512MB Unbuffered DIMM
DDR SDRAM
Physical Dimensions : 16Mx64 (M368L1624FTM)
Units : Inches (Millimeters)
5.25 ± 0.005
(133.350 ± 0.13)
0.118
(3.00)
5.077
(128.950)
0.7
(17.80)
0.393
B
0.100 Min
(2.30 Min)
A
(10.00)
(2X) 0.157
(4.00)
1.25 ± 0.006
(31.75 ±0.15)
2.500
0.10 M
1.95
2.55
(64.77)
C B A
0.098 Max
(2.47 Max)
(49.53)
0.157
(4.00)
0.100
0.26
(6.62)
0.250
(6.350)
(2.50 )
0.050 ± 0.0039
(1.270 ± 0.10)
0.0787
R (2.00)
0.1496
(3.80)
2.175
0.071
(1.80)
Detail A
0.118
(3.00)
0.039 ± 0.002
(1.000 ± 0.050)
0.0078 ±0.006
(0.20 ±0.15)
0.050
(1.270)
Detail B
0.1575
(4.00)
0.10 M C A M B
Tolerances : ± 0.005(.13) unless otherwise specified.
The used device is 16Mx16 DDR SDRAM, TSOPII.
DDR SDRAM Part No : K4H561638F-T***
Rev. 1.2 May, 2004
256MB, 512MB Unbuffered DIMM
DDR SDRAM
Physical Dimensions : 32Mx64 (M368L3223FTN)
Units : Inches (Millimeters)
5.25 ± 0.006
(133.350 ± 0.15)
0.118
(3.00)
5.077
(128.950)
B
A
0.7
(17.80)
0.100 Min
(2.30 Min)
0.393
(10.00)
(2X) 0.157
(4.00)
1.25 ± 0.006
(31.75 ±0.15)
2.500
0.10 M
2.55
1.95
(64.77)
(49.53)
C B A
0.07 Max
(1.20 Max)
0.157
(4.00)
0.100
0.26
(6.62)
0.250
(6.350)
(2.50 )
0.050 ± 0.0039
(1.270 ± 0.10)
0.0787
R (2.00)
0.1496
(3.80)
2.175
0.071
(1.80)
Detail A
0.118
(3.00)
0.039 ± 0.002
(1.000 ± 0.050)
0.0078 ± 0.006
(0.20 ± 0.15)
0.050
(1.270)
Detail B
0.1575
(4.00)
0.10 M C A M B
Tolerances : ± 0.005(.13) unless otherwise specified.
The used device is 32Mx8 DDR SDRAM, TSOPII.
DDR SDRAM Part No : K4H560838F-T***
Rev. 1.2 May, 2004
256MB, 512MB Unbuffered DIMM
DDR SDRAM
Physical Dimensions : 32Mx72 (M381L3223FTM)
Units : Inches (Millimeters)
5.25 ± 0.006
(133.350 ± 0.15)
0.118
(3.00)
5.077
(128.950)
B
A
0.7
(17.80)
0.100 Min
(2.30 Min)
0.393
(10.00)
(2X) 0.157
(4.00)
1.25 ± 0.006
(31.75 ±0.15)
2.500
0.10 M
2.55
1.95
(64.77)
(49.53)
C B A
0.07 Max
(1.20 Max)
0.157
(4.00)
0.100
0.26
(6.62)
0.250
(6.350)
(2.50 )
0.050 ± 0.0039
(1.270 ± 0.10)
0.0787
R (2.00)
0.1496
(3.80)
2.175
0.071
(1.80)
Detail A
0.118
(3.00)
0.039 ± 0.002
(1.000 ± 0.050)
0.0078 ± 0.006
(0.20 ± 0.15)
0.050
(1.270)
Detail B
0.1575
(4.00)
0.10 M C A M B
Tolerances : ± 0.005(.13) unless otherwise specified.
The used device is 32Mx8 DDR SDRAM, TSOPII.
DDR SDRAM Part No : K4H560838F-T***
Rev. 1.2 May, 2004
256MB, 512MB Unbuffered DIMM
DDR SDRAM
Physical Dimensions : 64Mx64 (M368L6423FTN)
Units : Inches (Millimeters)
5.25 ± 0.006
(133.350 ± 0.15)
0.118
(3.00)
5.077
(128.950)
B
A
0.7
(17.80)
0.100 Min
(2.30 Min)
0.393
(10.00)
(2X) 0.157
(4.00)
1.25 ± 0.006
(31.75 ±0.15)
2.500
0.10 M
2.55
1.95
(64.77)
(49.53)
C B A
0.145 Max
(3.67 Max)
0.157
(4.00)
0.100
0.26
(6.62)
0.250
(6.350)
(2.50 )
0.050 ± 0.0039
(1.270 ± 0.10)
0.0787
R (2.00)
0.1496
(3.80)
2.175
0.071
(1.80)
Detail A
0.118
(3.00)
0.039 ± 0.002
(1.000 ± 0.050)
0.0078 ± 0.006
(0.20 ± 0.15)
0.050
(1.270)
Detail B
0.1575
(4.00)
0.10 M C A M B
Tolerances : ± 0.005(.13) unless otherwise specified.
The used device is 32Mx8 DDR SDRAM, TSOPII.
DDR SDRAM Part No : K4H560838F-T***
Rev. 1.2 May, 2004
256MB, 512MB Unbuffered DIMM
DDR SDRAM
Physical Dimensions : 64Mx72 (M381L6423ETM)
Units : Inches (Millimeters)
5.25 ± 0.006
(133.350 ± 0.15)
0.118
(3.00)
5.077
(128.950)
B
A
0.7
(17.80)
0.100 Min
(2.30 Min)
0.393
(10.00)
(2X) 0.157
(4.00)
1.25 ± 0.006
(31.75 ±0.15)
2.500
0.10 M
2.55
1.95
(64.77)
(49.53)
C B A
0.145 Max
(3.67 Max)
0.157
(4.00)
0.100
0.26
(6.62)
0.250
(6.350)
(2.50 )
0.050 ± 0.0039
(1.270 ± 0.10)
0.0787
R (2.00)
0.1496
(3.80)
2.175
0.071
(1.80)
Detail A
0.118
(3.00)
0.039 ± 0.002
(1.000 ± 0.050)
0.0078 ± 0.006
(0.20 ± 0.15)
0.050
(1.270)
Detail B
0.1575
(4.00)
0.10 M C A M B
Tolerances : ± 0.005(.13) unless otherwise specified.
The used device is 32Mx8 DDR SDRAM, TSOPII.
DDR SDRAM Part No : K4H560838F-T***
Rev. 1.2 May, 2004
Similar pages