SCLS147E − DECEMBER 1982 − REVISED SEPTEMBER 2003 D Wide Operating Voltage Range of 2 V to 6 V D High-Current 3-State Outputs Drive Bus D D D D Lines Directly or Up To 15 LSTTL Loads D Low Power Consumption, 80-µA Max ICC SN54HC573A . . . J OR W PACKAGE SN74HC573A . . . DB, DW, N, OR PW PACKAGE (TOP VIEW) 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 VCC 1Q 2Q 3Q 4Q 5Q 6Q 7Q 8Q LE 3D 4D 5D 6D 7D OE VCC 1Q 20 2D 1D 1 SN54HC573A . . . FK PACKAGE (TOP VIEW) 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 2Q 3Q 4Q 5Q 6Q 8D GND LE 8Q 7Q OE 1D 2D 3D 4D 5D 6D 7D 8D GND Typical tpd = 21 ns ±6-mA Output Drive at 5 V Low Input Current of 1 µA Max Bus-Structured Pinout description/ordering information These octal transparent D-type latches feature 3-state outputs designed specifically for driving highly capacitive or relatively low-impedance loads. They are particularly suitable for implementing buffer registers, I/O ports, bidirectional bus drivers, and working registers. While the latch-enable (LE) input is high, the Q outputs respond to the data (D) inputs. When LE is low, the outputs are latched to retain the data that was set up. A buffered output-enable (OE) input can be used to place the eight outputs in either a normal logic state (high or low logic levels) or the high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. The high-impedance state and increased drive provide the capability to drive bus lines without interface or pullup components. ORDERING INFORMATION PDIP − N SN74HC573AN Tube of 40 SN74HC573ADW Reel of 2500 SN74HC573ADWR Reel of 2000 SN74HC573ADBR Reel of 2000 SN74HC573APWR Reel of 250 SN74HC573APWT CDIP − J Tube of 25 SNJ54HC573AJ SNJ54HC573AJ CFP − W Tube of 150 SNJ54HC573AW SNJ54HC573AW LCCC − FK Tube of 55 SNJ54HC573AFK SSOP − DB TSSOP − PW −55°C −55 C to 125 125°C C TOP-SIDE MARKING Tube of 25 SOIC − DW −40°C to 85°C ORDERABLE PART NUMBER PACKAGE† TA SN74HC573AN HC573A HC573A HC573A SNJ54HC573AFK † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2003, Texas Instruments Incorporated !"# $"%&! '#( '"! ! $#!! $# )# # #* "# '' +,( '"! $!#- '# #!#&, !&"'# #- && $##( $'"! !$& . /0 && $## # ##' "&# )#+# #'( && )# $'"! $'"! $!#- '# #!#&, !&"'# #- && $##( POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SCLS147E − DECEMBER 1982 − REVISED SEPTEMBER 2003 description/ordering information (continued) To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. OE does not affect the internal operations of the latches. Old data can be retained or new data can be entered while the outputs are in the high-impedance state. FUNCTION TABLE (each latch) INPUTS OE LE D OUTPUT Q L H H H L H L L L L X Q0 H X X Z logic diagram (positive logic) OE LE 1 11 C1 1D 2 19 1Q 1D To Seven Other Channels absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V Input clamp current, IIK (VI < 0 or VI > VCC) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Output clamp current, IOK (VO < 0 or VO > VCC) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±35 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±70 mA Package thermal impedance, θJA (see Note 2): DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70°C/W DW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69°C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51-7. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SCLS147E − DECEMBER 1982 − REVISED SEPTEMBER 2003 recommended operating conditions (see Note 3) SN54HC573A VCC VIH Supply voltage VCC = 2 V VCC = 4.5 V High-level input voltage VCC = 6 V VCC = 2 V VIL VI VO tt MIN NOM MAX 2 5 6 Input voltage MAX 2 5 6 3.15 3.15 4.2 4.2 0 VCC = 6 V UNIT V V 0.5 0.5 1.35 1.35 1.8 1.8 VCC VCC VCC = 2 V VCC = 4.5 V Input transition (rise and fall) time NOM 1.5 0 Output voltage MIN 1.5 VCC = 4.5 V VCC = 6 V Low-level input voltage SN74HC573A 0 VCC VCC 0 1000 1000 500 500 400 400 V V V ns TA Operating free-air temperature −55 125 −40 85 °C NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VOH VOL TEST CONDITIONS VI = VCC or 0, MIN MAX SN74HC573A MIN MAX UNIT 1.9 1.998 1.9 1.9 IOH = −20 µA 4.4 4.499 4.4 4.4 6V 5.9 5.999 5.9 5.9 IOH = −6 mA IOH = −7.8 mA 4.5 V 3.98 4.3 3.7 3.84 6V 5.48 5.8 5.2 5.34 2V 0.002 0.1 0.1 0.1 IOL = 20 µA 4.5 V 0.001 0.1 0.1 0.1 6V 0.001 0.1 0.1 0.1 4.5 V 0.17 0.26 0.4 0.33 6V 0.15 0.26 0.4 0.33 6V ±0.1 ±100 ±1000 ±1000 nA 6V ±0.01 ±0.5 ±10 ±5 µA 8 160 80 µA 10 10 10 pF IOL = 6 mA IOL = 7.8 mA ICC Ci SN54HC573A 2V VI = VIH or VIL VI = VCC or 0 VO = VCC or 0 TA = 25°C MIN TYP MAX 4.5 V VI = VIH or VIL II IOZ VCC IO = 0 6V 2 V to 6 V POST OFFICE BOX 655303 3 • DALLAS, TEXAS 75265 V V 3 SCLS147E − DECEMBER 1982 − REVISED SEPTEMBER 2003 timing requirements over recommended operating free-air temperature range (unless otherwise noted) VCC tw Pulse duration, LE high tsu Setup time, data before LE↓ th Hold time, data after LE↓ TA = 25°C MIN MAX SN54HC573A MIN MAX SN74HC573A MIN 2V 80 120 100 4.5 V 16 24 20 6V 14 20 17 2V 50 75 63 4.5 V 10 15 13 6V 9 13 11 2V 20 24 24 4.5 V 5 5 5 6V 5 5 5 MAX UNIT ns ns ns switching characteristics over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Figure 1) PARAMETER FROM (INPUT) D ten tdis tt 4 OE OE SN54HC573A SN74HC573A VCC 2V 77 175 265 220 Q 4.5 V 26 35 53 44 6V 23 30 45 38 2V 87 175 265 220 4.5 V 27 35 53 44 6V 23 30 45 38 2V 68 150 225 190 4.5 V 24 30 45 38 6V 21 26 38 32 2V 47 150 225 190 4.5 V 23 30 45 38 6V 21 26 38 32 2V 28 60 90 75 4.5 V 8 12 18 15 6V 6 10 15 13 tpd LE TA = 25°C MIN TYP MAX TO (OUTPUT) Any Q Any Q Any Q Any Q POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MIN MAX MIN MAX UNIT ns ns ns ns SCLS147E − DECEMBER 1982 − REVISED SEPTEMBER 2003 switching characteristics over recommended operating free-air temperature range, CL = 150 pF (unless otherwise noted) (see Figure 1) PARAMETER SN54HC573A SN74HC573A TO (OUTPUT) VCC 2V 95 200 300 250 D Q 4.5 V 33 40 60 50 6V 21 34 51 43 2V 103 225 335 285 4.5 V 33 45 67 57 6V 29 38 57 48 tpd LE ten TA = 25°C TYP MAX FROM (INPUT) Any Q OE Any Q tt Any Q MIN MIN MAX MIN MAX 2V 85 200 300 250 4.5 V 29 40 60 50 6V 26 34 51 43 2V 60 210 315 265 4.5 V 17 42 63 53 6V 14 36 53 45 UNIT ns ns ns operating characteristics, TA = 25°C PARAMETER Cpd TEST CONDITIONS Power dissipation capacitance per latch No load POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TYP 50 UNIT pF 5 SCLS147E − DECEMBER 1982 − REVISED SEPTEMBER 2003 PARAMETER MEASUREMENT INFORMATION VCC PARAMETER S1 Test Point From Output Under Test ten RL tPZH RL CL 50 pF or 150 pF 1 kΩ tPZL tdis S2 tPLZ 1 kΩ 50 pF −− 50 pF or 150 pF tpd or tt LOAD CIRCUIT 50% Closed Closed Open Open Closed Closed Open Open Open 50% 0V 50% tsu 0V tw Data 50% Input 10% VCC Low-Level Pulse 50% 50% 50% 0V tPLH 50% 10% tPHL 90% 90% tr tPHL 90% tf 50% 10% Output Control (Low-Level Enabling) 50% 10% V OL tf tPZL Output Waveform 1 (See Note B) VOH tPZH VOH tPLH 50% 10% 90% 90% VCC 50% 10% 0 V tf VOLTAGE WAVEFORMS SETUP AND HOLD AND INPUT RISE AND FALL TIMES VCC 50% th tr 0V VOLTAGE WAVEFORMS PULSE DURATIONS Out-ofPhase Output Open VCC Reference Input VCC High-Level Pulse In-Phase Output S2 tPHZ CL (see Note A) Input S1 90% VOL tr VOLTAGE WAVEFORMS PROPAGATION DELAY AND OUTPUT TRANSITION TIMES VCC 50% Output Waveform 2 (See Note B) 50% 0V tPLZ ≈VCC 50% 10% ≈VCC VOL tPHZ 50% 90% VOH ≈0 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES FOR 3-STATE OUTPUTS NOTES: A. CL includes probe and test-fixture capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. Phase relationships between waveforms were chosen arbitrarily. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr = 6 ns, tf = 6 ns. D. The outputs are measured one at a time with one input transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. Figure 1. Load Circuit and Voltage Waveforms 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 29-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp ACTIVE CDIP J 20 1 TBD A42 N / A for Pkg Type 5962-8512801VSA ACTIVE CFP W 20 25 TBD Call TI N / A for Pkg Type 85128012A ACTIVE LCCC FK 20 1 TBD Call TI Call TI 8512801RA ACTIVE CDIP J 20 1 TBD Call TI Call TI 8512801SA ACTIVE CFP W 20 1 TBD Call TI Call TI JM38510/65406BRA ACTIVE CDIP J 20 1 TBD A42 N / A for Pkg Type M38510/65406BRA ACTIVE CDIP J 20 1 TBD A42 N / A for Pkg Type A42 N / A for Pkg Type SN54HC573AJ ACTIVE CDIP J 20 1 TBD SN74HC573ADBR ACTIVE SSOP DB 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC573ADBRE4 ACTIVE SSOP DB 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC573ADBRG4 ACTIVE SSOP DB 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC573ADW ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC573ADWE4 ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC573ADWG4 ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC573ADWR ACTIVE SOIC DW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC573ADWRE4 ACTIVE SOIC DW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC573ADWRG4 ACTIVE SOIC DW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC573AN ACTIVE PDIP N 20 20 Pb-Free (RoHS) SN74HC573AN3 OBSOLETE PDIP N 20 SN74HC573ANE4 ACTIVE PDIP N 20 SN74HC573APWLE OBSOLETE TSSOP PW 20 SN74HC573APWR ACTIVE TSSOP PW 20 20 Pb-Free (RoHS) TBD 2000 Green (RoHS & no Sb/Br) Addendum-Page 1 CU NIPDAU N / A for Pkg Type Call TI Call TI CU NIPDAU N / A for Pkg Type Call TI Samples (Requires Login) 5962-8512801VRA TBD (3) Call TI CU NIPDAU Level-1-260C-UNLIM PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 29-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) SN74HC573APWRE4 ACTIVE TSSOP PW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC573APWRG4 ACTIVE TSSOP PW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC573APWT ACTIVE TSSOP PW 20 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC573APWTE4 ACTIVE TSSOP PW 20 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC573APWTG4 ACTIVE TSSOP PW 20 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SNJ54HC573AFK ACTIVE LCCC FK 20 1 TBD SNJ54HC573AJ ACTIVE CDIP J 20 1 TBD A42 N / A for Pkg Type SNJ54HC573AW ACTIVE CFP W 20 1 TBD Call TI N / A for Pkg Type POST-PLATE N / A for Pkg Type (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com 29-Aug-2012 In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF SN54HC573A, SN54HC573A-SP, SN74HC573A : • Catalog: SN74HC573A, SN54HC573A • Automotive: SN74HC573A-Q1, SN74HC573A-Q1 • Military: SN54HC573A • Space: SN54HC573A-SP NOTE: Qualified Version Definitions: • Catalog - TI's standard catalog product • Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects • Military - QML certified for Military and Defense Applications • Space - Radiation tolerant, ceramic packaging and qualified for use in Space-based application Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device SN74HC573ADBR Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SSOP DB 20 2000 330.0 16.4 8.2 7.5 2.5 12.0 16.0 Q1 SN74HC573ADWR SOIC DW 20 2000 330.0 24.4 10.8 13.0 2.7 12.0 24.0 Q1 SN74HC573APWR TSSOP PW 20 2000 330.0 16.4 6.95 7.1 1.6 8.0 16.0 Q1 SN74HC573APWT TSSOP PW 20 250 330.0 16.4 6.95 7.1 1.6 8.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN74HC573ADBR SSOP DB 20 2000 367.0 367.0 38.0 SN74HC573ADWR SOIC DW 20 2000 367.0 367.0 45.0 SN74HC573APWR TSSOP PW 20 2000 367.0 367.0 38.0 SN74HC573APWT TSSOP PW 20 250 367.0 367.0 38.0 Pack Materials-Page 2 MECHANICAL DATA MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001 DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE 28 PINS SHOWN 0,38 0,22 0,65 28 0,15 M 15 0,25 0,09 8,20 7,40 5,60 5,00 Gage Plane 1 14 0,25 A 0°–ā8° 0,95 0,55 Seating Plane 2,00 MAX 0,10 0,05 MIN PINS ** 14 16 20 24 28 30 38 A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90 A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30 DIM 4040065 /E 12/01 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-150 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated