Mitsubishi M38C88E1-XXXFP Single-chip 8-bit cmos microcomputerã ã ã Datasheet

MIN
I
L
E
ARY
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
PR
DESCRIPTION
The 38C8 group is the 8-bit microcomputer based on the 740 family
core technology.
The 38C8 group has a LCD drive control circuit (bias control, time
sharing control), a 10-bit A-D converter, and a Serial I/O as additional
functions.
The various microcomputers in the 38C8 group include variations of
internal memory size and packaging. For details, refer to the section
on part numbering.
FEATURES
●Basic machine-language instructions ....................................... 71
●The minimum instruction execution time ............................ 0.5 µs
(at 8 MHz oscillation frequency)
●Memory size
ROM ............................................................................ 60 K bytes
RAM ............................................................................ 2048 bytes
●Programmable input/output ports ............................................. 35
●Software pull-up resistors
.................................................................. Ports P0–P3, P41–P4 7
●Interrupts ................................................... 15 sources, 15 vectors
(includes key input interrupt)
●Timers ............................................................ 8-bit ✕ 3, 16-bit ✕ 2
●Serial I/O ........................ 8-bit ✕ 1 (UART or Clock-synchronized)
●A-D converter (32 kHz operating available) ... 10-bit ✕ 8 channels
MITSUBISHI MICROCOMPUTERS
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
●LCD drive control circuit
Bias ................................................................................... 1/5, 1/7
Duty .............................................................................. 1/16, 1/32
Common output ............................................................... 16 or 32
Segment output ............................................................... 52 or 68
●Main clock generating circuit (RC oscillation selectable)
...................... (connect to external ceramic resonator or resistor)
●Sub-clock generating circuit
............................................. (connect to quartz-crystal oscilaltor)
●Power source voltage
In high-speed mode .................................................... 4.0 to 5.5 V
In middle-speed mode ................................................ 2.2 to 5.5 V
In low-speed mode ..................................................... 2.2 to 5.5 V
●Power dissipation
In high-speed mode ........................................................... 30 mW
(at 8 MHz oscillation frequency, at 5 V power source voltage)
In low-speed mode ............................................................. 60 µW
(at 32 kHz oscillation frequency, at 3 V power source voltage, at
WIT state, at voltage multiplier operating, LCD drive waveform
generating state)
●Operating temperature range ................................... – 20 to 85°C
APPLICATIONS
Dot-matrix-type displays
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
n.
atio
ific
pec ject to
s
l
ub
na
a fi are s
not
its
is is ric lim
h
T
et
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
77
76
75
74
73
109
110
111
112
113
114
115
116
117
118
72
71
70
69
68
67
66
65
64
63
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
COM5
COM4
COM3
COM2
COM1
COM0
VL1
VL2
VL3
VL4
VL5
C3
C2
C1
VLIN
VSS (NC)
NC
VSS
P27
P26
P25
P24
P23
P22
P21
P20
P47/SRDY
P46/SCLK
P45/TXD
P44/RXD
P43/CNTR1/BEEPP42/CNTR0/BEEP+
P41/INT1/ADT
P40/INT0
P07
P06
36
M38C89MF-XXXFP
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
SEG33
SEG32
SEG31
SEG30
SEG29
SEG28
SEG27
SEG26
SEG25
SEG24
SEG23
SEG22
SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
SEG9
SEG8
SEG7/COM23
SEG6/COM22
SEG5/COM21
SEG4/COM20
SEG3/COM19
SEG2/COM18
SEG1/COM17
SEG0/COM16
COM7
COM6
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
108
107
106
105
104
103
102
SEG34
SEG35
SEG36
SEG37
SEG38
SEG39
SEG40
SEG41
SEG42
SEG43
SEG44
SEG45
SEG46
SEG47
SEG48
SEG49
SEG50
SEG51
SEG52
SEG53
SEG54
SEG55
SEG56
SEG57
SEG58
SEG59
SEG60/COM31
SEG61/COM30
SEG62/COM29
SEG63/COM28
SEG64/COM27
SEG65/COM26
SEG66/COM25
SEG67/COM24
COM15
COM14
PIN CONFIGURATION (TOP VIEW)
Package type : 144P6Q-A
Fig. 1 M38C89MF-XXXFP pin configuration
2
COM13
COM12
COM11
COM10
COM9
COM8
P30/AIN0
P31/AIN1
P32/AIN2
P33/AIN3
NC
XIN
NC
VSS
XOUT
OSCSEL
VCC
NC
XCIN
XCOUT
NC
RESET
P10/AIN4
P11/AIN5
P12/AIN6
P13/AIN7
P14
P15
P16
P17
P00
P01
P02
P03
P04
P05
PCH
CPU
35 36 37 38 39 40 41 42
I/O port P0
63 64 65 66
I/O port P3
34 33 32 31 30 29 28 27
I/O port P4
P0 (8)
56
VCC
P3 (4)
PS
PCL
S
Y
X
A
51
Reset input
RESET
P4 (7)
φ
A-D converter (10)
53
54
Clock generating circuit
XCOUT
XCIN
58
Sub-clock Sub-clock
input
output
XOUT
Clock
output
Serial I/O (8)
61
XIN
Clock
input
I/O port P1
Timer X (16)
LCD RAM
(176 byte)
RAM
I/O port P2
19 20 21 22 23 24 25 26
P2 (8)
Timer 3 (8)
Timer 2 (8)
Timer Y (16)
Timer 1 (8)
Timer
ROM
43 44 45 46 47 48 49 50
P1 (8)
18
59
Data bus
VSS
VSS
FUNCTIONAL BLOCK DIAGRAM (Package: 144P6Q-A)
CNTR0, CNTR1
12
C3
13
C2
14
C1
15
VLIN
10
9
8
7
VL1 VL2 VL3 VL4 VL5
11
LCD
controller
COM0
COM1
COM2
3 COM3
2 COM4
1 COM5
144 COM6
143 COM7
142 SEG0/COM16
141 SEG1/COM17
140 SEG2/COM18
139 SEG3/COM19
138
SEG4/COM20
137 SEG5/COM21
136 SEG6/COM22
135
SEG7/COM23
134
SEG8
133 SEG9
132 SEG10
131 SEG11
130
SEG12
79
80
81
SEG61/COM30
SEG62/COM29
SEG63/COM28
78 SEG64/COM27
77 SEG65/COM26
76 SEG66/COM25
75 SEG67/COM24
74 COM15
73 COM14
72 COM13
71 COM12
70 COM11
69 COM10
68 COM9
67 COM8
82 SEG60/COM31
83 SEG59
84 SEG58
84 SEG57
84 SEG56
84 SEG55
4
5
6
IM
Key-on wake-up
L
PRE
INT0, INT1
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
RY
A
N
I
MITSUBISHI MICROCOMPUTERS
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Fig. 2 Functional block diagram
3
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
n.
atio
ific
pec ject to
s
l
ub
na
a fi are s
not
its
is is ric lim
h
T
et
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
PIN DESCRIPTION
Table 1 Pin description
Pin
Name
VCC , VSS
RESET
XIN
Power source
Reset input
Clock input
XOUT
Clock output
OSCSEL
RC oscillation
select
Sub-clock input
Sub-clock output
XCIN
XCOUT
VLIN
VL1 – VL5
COM0 –
COM32
SEG0 /COM16–
SEG7 /COM23,
SEG60COM31–
SEG67/COM24
SEG8 –SEG59
P00–P0 7
Power source
input for LCD
LCD power
source
Common output
Function except a port function
• Apply voltage of 4.0–5.5 V to VCC, and 0 V to VSS. (at high-speed mode)
• Reset input pin for active “L.”
• Input and output pins for the main clock generating circuit.
• Feedback resistor is built in between XIN pin and X OUT pin.
• Connect a ceramic resonator or a quartz-crystal oscillator between the XIN and XOUT pins to set the
oscillation frequency.
• If an external clock is used, connect the clock source to the XIN pin and leave the XOUT pin open.
• This pin determines the oscillation between XIN and XOUT. The oscillation method can be selected from
either by an oscillator or by a resistor.
• Input and output pins for sub-clock generating circuit. (Connect a quartz-crystal oscillator between the
XCIN and XCOUT pins to set the oscillation frequency. The clock generated the externals cannot be input
directly.)
• Reference voltage input pin for LCD.
• The input voltage to this pin is boosted threefold by voltage multiplier.
• LCD drive power source pins.
• LCD common output pins.
Segment output/
Common output
• LCD segment/common output pins.
Segment output
I/O port P0
• LCD segment output pins.
• 8-bit I/O port.
• CMOS compatible input level.
• CMOS 3-state output structure.
P14–P17
P10/AIN 4–
P13/AIN 7
P20–P2 7
P30/AIN 0 –
P33/AIN 3
I/O port P1
P40/INT 0
Input port P4
I/O port P2
I/O port P3
P41/INT 1/ADT I/O port P4
P42/CNTR0/
BEEP+,
P43/CNTR1/
BEEPP44/RxD,
P45/TxD,
P46/S CLK,
P47/S RDY
C1,
Voltage multiplier
C2,
C3
VSS (NC), NC
4
Function
• 4-bit I/O port.
• CMOS compatible input level.
• CMOS 3-state output structure.
• 1-bit input port.
• CMOS compatible input level.
• 7-bit I/O port.
• CMOS compatible input level.
• CMOS 3-state output structure.
• I/O direction register allows each pin to be individually
programmed as either input or output.
• A-D converter analog input pin
• Key-on wake-up interrupt input pin
• A-D converter analog input pin
• External interrupt pin
• External interrupt pin
• A-D trigger input pin
•Timer function I/O pin
• Serial I/O I/O pin
• External capacitor connect pins for a voltage multiplier of LCD.
• Non-function pins.
• Leave the VSS (NC) pin open.
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
PART NUMBERING
Product
M38C8
9
M
F
–XXX
FP
Package type
FP: 144P6Q-A package
ROM number
Omitted in One Time PROM version.
ROM/PROM size
1: 4096 bytes
9: 36864 bytes
2: 8192 bytes
A: 40960 bytes
3: 12288 bytes B: 45056 bytes
4: 16384 bytes C: 49152 bytes
5: 20480 bytes D: 53248 bytes
6: 24576 bytes E: 57344 bytes
7: 28672 bytes F: 61440 bytes
8: 32768 bytes
The first 128 bytes and the last 2 bytes of ROM
are reserved areas; they cannot be used.
Memory type
M: Mask ROM version
E: One Time PROM version
RAM size
0: 192 bytes
1: 256 bytes
2: 384 bytes
3: 512 bytes
4: 640 bytes
5: 768 bytes
6: 896 bytes
7: 1024 bytes
8: 1536 bytes
9: 2048 bytes
Fig. 3 Part numbering
5
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
n.
atio
ific
pec ject to
s
l
ub
na
a fi are s
not
its
is is ric lim
h
T
et
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GROUP EXPANSION
Packages
Mitsubishi plans to expand the 38C8 group as follows.
144P6Q-A ................................... 0.5 mm-pitch plastic molded QFP
Memory Type
Support for mask ROM and One Time PROM versions
Memory Size
ROM/PROM size ............................................................ 60 K bytes
RAM size ........................................................................ 2048 bytes
Memory Expansion Plan
Under development
ROM size (bytes)
M38C89MF/EF
60K
56K
48K
40K
32K
28K
24K
20K
16K
12K
8K
4K
192 256
384
512
640
768
896
1,024
1,536
2,048
RAM size (bytes)
Products under development or planning: the development schedule and specification may be revised without
notice. The development of planning products may be stopped.
Fig. 4 Memory expansion plan
Currently planning products are listed below.
Table 2 Support products
Product name
M38C89MF-XXXFP
M38C89EFFP
6
As of Dec. 2000
(P) ROM size (bytes)
ROM size for User in ( )
61440 (61310)
61440 (61310)
RAM size
(bytes)
2048
2048
Package
144P6Q-A
144P6Q-A
Remarks
Mask ROM version
One Time PROM version
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
FUNCTIONAL DESCRIPTION
CENTRAL PROCESSING UNIT (CPU)
[Stack Pointer (S)]
The accumulator is an 8-bit register. Data operations such as data
transfer, etc., are executed mainly through the accumulator.
The stack pointer is an 8-bit register used during subroutine calls
and interrupts. This register indicates start address of stored area
(stack) for storing registers during subroutine calls and interrupts.
The low-order 8 bits of the stack address are determined by the contents of the stack pointer. The high-order 8 bits of the stack address
are determined by the stack page selection bit. If the stack page
selection bit is “0” , the high-order 8 bits becomes “0016”. If the stack
page selection bit is “1”, the high-order 8 bits becomes “0116”.
The operations of pushing register contents onto the stack and popping them from the stack are shown in Figure 6.
Store registers other than those described in Figure 6 with program
when the user needs them during interrupts or subroutine calls.
[Index Register X (X)]
[Program Counter (PC)]
The index register X is an 8-bit register. In the index addressing modes,
the value of the OPERAND is added to the contents of register X and
specifies the real address.
The program counter is a 16-bit counter consisting of two 8-bit registers PCH and PCL. It is used to indicate the address of the next instruction to be executed.
The 38C8 group uses the standard 740 family instruction set. Refer
to the table of 740 family addressing modes and machine instructions or the 740 Family Software Manual for details on the instruction
set.
Machine-resident 740 family instructions are as follows:
The FST and SLW instruction cannot be used.
The STP, WIT, MUL, and DIV instruction can be used.
[Accumulator (A)]
[Index Register Y (Y)]
The index register Y is an 8-bit register. In partial instruction, the
value of the OPERAND is added to the contents of register Y and
specifies the real address.
b0
b7
A
Accumulator
b0
b7
X
Index register X
b0
b7
Y
b7
Index register Y
b0
S
b15
b7
PCH
Stack pointer
b0
Program counter
PCL
b7
b0
N V T B D I Z C
Processor status register (PS)
Carry flag
Zero flag
Interrupt disable flag
Decimal mode flag
Break flag
Index X mode flag
Overflow flag
Negative flag
Fig. 5 740 Family CPU register structure
7
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
n.
atio
ific
pec ject to
s
l
ub
na
a fi are s
not
its
is is ric lim
h
T
et
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
On-going Routine
Interrupt request
(Note)
M (S)
Execute JSR
Push return address
on stack
M (S)
(PCH)
(S)
(S) – 1
M (S)
(PCL)
(S)
(S)– 1
(S)
M (S)
(S)
M (S)
(S)
Subroutine
POP return
address from stack
(S) + 1
(PCL)
M (S)
(S)
(S) + 1
(PCH)
M (S)
(S) – 1
(PCL)
Push return address
on stack
(S) – 1
(PS)
Push contents of processor
status register on stack
(S) – 1
Interrupt
Service Routine
Execute RTS
(S)
(PCH)
I Flag is set from “0” to “1”
Fetch the jump vector
Execute RTI
Note: Condition for acceptance of an interrupt
(S)
(S) + 1
(PS)
M (S)
(S)
(S) + 1
(PCL)
M (S)
(S)
(S) + 1
(PCH)
M (S)
POP contents of
processor status
register from stack
POP return
address
from stack
Interrupt enable flag is “1”
Interrupt disable flag is “0”
Fig. 6 Register push and pop at interrupt generation and subroutine call
Table 3 Push and pop instructions of accumulator or processor status register
Accumulator
Processor status register
8
Push instruction to stack
Pop instruction from stack
PHA
PHP
PLA
PLP
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
[Processor status register (PS)]
The processor status register is an 8-bit register consisting of 5 flags
which indicate the status of the processor after an arithmetic operation and 3 flags which decide MCU operation. Branch operations can
be performed by testing the Carry (C) flag , Zero (Z) flag, Overflow
(V) flag, or the Negative (N) flag. In decimal mode, the Z, V, N flags
are not valid.
•Bit 0: Carry flag (C)
The C flag contains a carry or borrow generated by the arithmetic
logic unit (ALU) immediately after an arithmetic operation. It can
also be changed by a shift or rotate instruction.
•Bit 1: Zero flag (Z)
The Z flag is set if the result of an immediate arithmetic operation
or a data transfer is “0”, and cleared if the result is anything other
than “0”.
•Bit 2: Interrupt disable flag (I)
The I flag disables all interrupts except for the interrupt
generated by the BRK instruction.
Interrupts are disabled when the I flag is “1”.
•Bit 3: Decimal mode flag (D)
The D flag determines whether additions and subtractions are
executed in binary or decimal. Binary arithmetic is executed when
this flag is “0”; decimal arithmetic is executed when it is “1”.
Decimal correction is automatic in decimal mode. Only the ADC
•Bit 4: Break flag (B)
The B flag is used to indicate that the current interrupt was
generated by the BRK instruction. The BRK flag in the processor
status register is always “0”. When the BRK instruction is used to
generate an interrupt, the processor status register is pushed
onto the stack with the break flag set to “1”.
•Bit 5: Index X mode flag (T)
When the T flag is “0”, arithmetic operations are performed
between accumulator and memory. When the T flag is “1”, direct
arithmetic operations and direct data transfers are enabled
between memory locations.
•Bit 6: Overflow flag (V)
The V flag is used during the addition or subtraction of one byte
of signed data. It is set if the result exceeds +127 to -128. When
the BIT instruction is executed, bit 6 of the memory location
operated on by the BIT instruction is stored in the overflow flag.
•Bit 7: Negative flag (N)
The N flag is set if the result of an arithmetic operation or data
transfer is negative. When the BIT instruction is executed, bit 7 of
the memory location operated on by the BIT instruction is stored
in the negative flag.
Table 4 Set and clear instructions of each bit of processor status register
Set instruction
Clear instruction
C flag
SEC
CLC
Z flag
–
–
I flag
SEI
CLI
D flag
SED
CLD
B flag
–
–
T flag
SET
CLT
V flag
–
CLV
N flag
–
–
9
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
n.
atio
ific
pec ject to
s
l
ub
na
a fi are s
not
its
is is ric lim
h
T
et
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
[CPU Mode Register (CPUM)] 003B16
The CPU mode register contains the stack page selection bit and the
internal system clock selection bit.
The CPU mode register is allocated at address 003B16 .
b7
b0
CPU mode register
(CPUM (CM) : address 003B16)
Processor mode bits
b1 b0
0 0 : Single-chip mode
0 1 :
1 0 : Not available
1 1 :
Stack page selection bit
0 : 0 page
1 : 1 page
Not used (returns “1” when read)
(Do not write “0” to this bit)
Sub-clock (XCIN–XCOUT) stop bit
0 : Stopped
1 : Oscillating
Main clock (XIN–XOUT) stop bit
0 : Oscillating
1 : Stopped
Main clock division ratio selection bit
0 : f(XIN)/2 (high-speed mode)
1 : f(XIN)/8 (middle-speed mode)
Internal system clock selection bit
0 : XIN–XOUT selected (middle-/high-speed mode)
1 : XCIN–XCOUT selected (low-speed mode)
Fig. 7 Structure of CPU mode register
10
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MEMORY
Special Function Register (SFR) Area
The Special Function Register area in the zero page contains control
registers such as I/O ports and timers.
Zero Page
Access to this area with only 2 bytes is possible in the zero page
addressing mode.
Special Page
RAM
RAM is used for data storage and for stack area of subroutine calls
and interrupts.
Access to this area with only 2 bytes is possible in the special page
addressing mode.
ROM
The first 128 bytes and the last 2 bytes of ROM are reserved for
device testing and the rest is user area for storing programs.
Interrupt Vector Area
The interrupt vector area contains reset and interrupt vectors.
RAM area
RAM size
(bytes)
000016
Address
XXXX16
192
00FF16
256
013F16
384
01BF16
512
023F16
640
02BF16
768
033F16
896
03BF16
1024
043F16
1536
063F16
2048
083F16
SFR area
004016
Zero page
LCD display RAM area✽
RAM
013016
XXXX16
034016
LCD display RAM area✽
043016
ROM area
ROM size
(bytes)
Address
YYYY16
Address
ZZZZ16
084016
4096
F00016
F08016
YYYY16
8192
E00016
E08016
12288
D00016
D08016
16384
C00016
C08016
20480
B00016
B08016
24576
A00016
A08016
28672
900016
908016
32768
800016
808016
36864
700016
708016
40960
600016
608016
45056
500016
508016
49152
400016
408016
53248
300016
308016
57344
200016
208016
61440
100016
108016
Not used
Reserved ROM area
(128 bytes)
ZZZZ16
ROM
FF0016
FFDC16
Interrupt vector area
Special page
FFFE16
FFFF16
Reserved ROM area
✽ The stard address of the LCD display area can be switched either zero page (addresses 004016–00EF16) or 3 page (addresses
034016 –03EF16) by software. Immediately after reset released, 3 page is selected.
Fig. 8 Memory map diagram
11
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
n.
atio
ific
pec ject to
s
l
ub
na
a fi are s
not
its
is is ric lim
h
T
et
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
000016 Port P0 (P0)
000116 Port P0 direction register (P0D)
000216 Port P1 (P1)
002016 Timer X (low-order) (TXL)
002116 Timer X (high-order) (TXH)
002216 Timer Y (low-order) (TYL)
000316 Port P1 direction register (P1D)
000416 Port P2 (P2)
000516 Port P2 direction register (P2D)
000616 Port P3 (P3)
002316 Timer Y (high-order) (TYH)
002416 Timer 1 (T1)
000716 Port P3 direction register (P3D)
000816 Port P4 (P4)
000916 Port P4 direction register (P4D)
000A16
000B16
002516 Timer 2 (T2)
002616 Timer 3 (T3)
002716 Timer X mode register (TXM)
002816 Timer Y mode register (TYM)
002916 Timer 123 mode register (T123M)
002A16
000C16
002B16
002C16
000D16
002D16
000E16
002E16
002F16
000F16
001016
003016
001116
001216
003116 A-D control register (ADCON)
003216 A-D conversion register (low-order) (ADL)
001316
003316 A-D conversion register (high-order) (ADH)
003416
001416
001516
001616 PULL register A (PULLA)
001716 PULL register B (PULLB)
001816 Transmit/Receive buffer register (TB/RB)
001916 Serial I/O status register (SIOSTS)
001A16 Serial I/O control register (SIOCON)
001B16 UART control register (UARTCON)
001C16 Baud rate generator (BRG)
001D16
001E16
001F16
Fig. 9 Memory map of special function register (SFR)
12
38C8 Group
003516
003616
003716 LCD control register 1 (LC1)
003816 LCD control register 2 (LC2)
003916 LCD mode register (LM)
003A16 Interrupt edge selection register (INTEDGE)
003B16 CPU mode register (CPUM)
003C16 Interrupt request register 1 (IREQ1)
003D16 Interrupt request register 2 (IREQ2)
003E16 Interrupt control register 1 (ICON1)
003F16 Interrupt control register 2 (ICON2)
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
I/O PORTS
[Direction Registers]
The I/O ports P0–P3 and P41–P47 have direction registers which
determine the input/output direction of each individual pin. Each bit
in a direction register corresponds to one pin, each pin can be set to
be input port or output port.
When “0” is written to the bit corresponding to a pin, that pin becomes an input pin. When “1” is written to that bit, that pin becomes
an output pin.
If data is read from a pin set to output, the value of the port output
latch is read, not the value of the pin itself. Pins set to input are floating. If a pin set to input is written to, only the port output latch is
written to and the pin remains floating.
Pull-up Control
By setting the PULL register A (address 001616) or the PULL register
B (address 001716 ), ports P0 to P4 except for port P40 can control
pull-up with a program.
However, the contents of PULL register A and PULL register B do not
affect ports programmed as the output ports.
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
b7
b0
PULL register A
(PULLA: address 001616)
P00–P03 pull-up
P04–P07 pull-up
P10–P13 pull-up
P14–P17 pull-up
P20–P23 pull-up
P24–P27 pull-up
P30–P33 pull-up
Not used (return “0” when read)
b7
b0
PULL register B
(PULLB: address 001716)
Not used (return “0” when read)
P41 pull-up
P42 pull-up
P43 pull-up
P44 pull-up
P45 pull-up
P46 pull-up
P47 pull-up
0: No pull-up
1: Pull-up
Note: The contents of PULL register A and PULL register B do
not affect ports programmed as the output port.
Fig. 10 Structure of PULL register A and PULL register B
13
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
n.
atio
ific
pec ject to
s
l
ub
na
a fi are s
not
its
is is ric lim
h
T
et
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 5 List of I/O port function
Pin
P00–P0 7
P10/AN4–
P13/AN7
P14–P1 7
P20–P2 7
Name
Port P0
Port P1
Input/Output
Input/Output,
individual bits
I/O format
CMOS 3-state output
Port P2
Input/Output,
individual bits
P30/AN0–
P33/AN3
P40/INT 0
Port P3
Input/Output,
individual bits
Input
CMOS compatible input
level
CMOS 3-state output
CMOS 3-state output
Key input (key-on
wake-up) interrupt input
A-D converter input
CMOS compatible input
level
CMOS compatible input
level
CMOS 3-state output
External interrupt input
P41/INT 1
P42/CNTR0/
BEEP+
P43/CNTR1/
BEEPP44/RxD
P45/TxD
P46/S CLK
P47/S RDY
COM0–COM7,
COM8–COM15
SEG0/COM16–
SEG7/COM23,
SEG60/COM31–
SEG67/COM24
SEG8–SEG59
14
Port P4
Input/Output,
individual bits
Non-port function
Timer X function I/O
Timer Y function input
Serial I/O funtion
I/O
Common
Output
LCD common output
Segment/
Common
LCD segment output
LCD common ouput
Segment
LCD segment output
Related SFRs
PULL register A
PULL register A
A-D control register
PULL register A
PULL register A
Interrupt control register 2
Ref. No.
(1)
(2)
PULL register A
A-D control register
PULL register B
Interrupt edge select
register
PULL register B
Timer X mode register
PULL register B
Timer Y mode register
PULL register B
Serial I/O control register
Serial I/O status register
UART control register
LCD mode register
(2)
(1)
(1)
(3)
(1)
(4)
(5)
(6)
(7)
(8)
(9)
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
(2) Ports P10–P13, P3
(1) Ports P0, P14–P17, P2, P41
Pull-up control
Pull-up control
Direction
register
Direction
register
Data bus
Port latch
Data bus
Port latch
A-D converter input
Analog input pin selection bit
Key-on wake-up interrupt input
INT1 interrupt input, ADT
Except P0, P1
(3) Port P40
Data bus
INT0 interrupt input
(4) Port P42
(5) Port P43
Pull-up control
Pull-up control
Direction
register
Data bus
Direction
register
Port latch
Data bus
Port latch
Buzzer output mode
Timer output
Buzzer output mode
Timer output
CNTR0 interrupt input
CNTR1 interrupt input
Fig. 11 Port block diagram (1)
15
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
n.
atio
ific
pec ject to
s
l
ub
na
a fi are s
not
its
is is ric lim
h
T
et
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
(6) Port P44
(7) Port P45
Serial I/O enable bit
Receive enalble bit
Pull-up control
Direction
register
Port latch
Data bus
Databus
Serial I/O input
(9) Port P47
Serial I/O synchronous
clock selection bit
Serial I/O enable bit
Pull-up control
Serial I/O mode selection bit
Serial I/O enable bit
Direction
register
Port latch
Serial I/O ready output
Serial I/O clock input
Fig. 12 Port block diagram (2)
Serial I/O mode selection bit
Serial I/O enable bit
SRDY output enable bit
Direction
register
Data bus
Port latch
Serial I/O clock output
16
Port latch
Serial I/O output
(8) Port P46
Data bus
Pull-up control
P45/TxD P-channel output disable bit
Serial I/O enable bit
Transmit enable bit
Direction
register
Pull-up control
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
INTERRUPTS
Interrupt Operation
Interrupts occur by fifteen sources: six external, eight internal, and
one software.
By acceptance of an interrupt, the following operations are automatically performed:
1. The processing being executed is stopped.
2. The contents of the program counter and processor status register are automatically pushed onto the stack.
3. The interrupt disable flag is set and the corresponding interrupt
request bit is cleared.
4. The interrupt jump destination address is read from the vector
table into the program counter.
Interrupt Control
Each interrupt except the BRK instruction interrupt have both an interrupt request bit and an interrupt enable bit, and is controlled by the
interrupt disable flag. An interrupt occurs if the corresponding interrupt request and enable bits are “1” and the interrupt disable flag is
“0”.
Interrupt enable bits can be set or cleared by software. Interrupt request bits can be cleared by software, but cannot be set by software.
The BRK instruction interrupt and reset cannot be disabled with any
flag or bit. The I flag disables all interrupts except the BRK instruction
interrupt and reset. If several interrupts requests occurs at the same
time the interrupt with highest priority is accepted first.
■Notes on interrupts
When setting the followings, the interrupt request bit may be set to
“1”.
•When setting external interrupt active edge
Related register: Interrupt edge selection register (address 3A16 )
Timer X mode register (address 2716 )
Timer Y mode register (address 2816)
•When switching interrupt sources of an interrupt vector address
where two or more interrupt sources are allocated
Related register: AD control regsiter (address 3116)
When not requiring for the interrupt occurrence synchronized with
these setting, take the following sequence.
➀Set the corresponding interrupt enable bit to “0” (disabled).
➁Set the interrupt edge select bit (active edge switch bit) or the interrupt source select bit to “1”.
➂Set the corresponding interrupt request bit to “0” after 1 or more
instructions have been executed.
➃Set the corresponding interrupt enable bit to “1” (enabled).
Table 6 Interrupt vector addresses and priority
Vector Addresses (Note 1)
Interrupt Source Priority
High
Low
Reset (Note 2)
1
FFFD16
FFFC16
INT0
2
FFFB16
FFFA16
Interrupt Request
Generating Conditions
Remarks
At reset
At detection of either rising or falling edge of
INT0 intput
At detection of either rising or falling edge of
INT1 input
At completion of serial I/O data reception
Non-maskable
External interrupt
(active edge selectable)
External interrupt
(active edge selectable)
Valid when serial I/O is selected
Valid when serial I/O is selected
INT1
3
FFF916
FFF816
Serial I/O
reception
Serial I/O
transmission
Timer X
Timer Y
Timer 2
Timer 3
CNTR0
4
FFF716
FFF616
5
FFF516
FFF416
6
7
8
9
10
FFF316
FFF116
FFEF16
FFED16
FFEB16
FFF216
FFF016
FFEE16
FFEC16
FFEA16
CNTR1
11
FFE916
FFE816
Timer 1
Key input (Keyon wake-up)
A-D conversion
12
13
FFE716
FFE116
FFE616
FFE016
14
FFDF16
FFDE16
At completion of serial I/O transmission shift
or when transmission buffer is empty
At timer X underflow
At timer Y underflow
At timer 2 underflow
At timer 3 underflow
At detection of either rising or falling edge of
CNTR0 input
At detection of either rising or falling edge of
CNTR1 input
At timer 1 underflow
At falling of port P2 (at input) input logical level
AND
At completion of A-D conversion
BRK instruction
15
FFDD16
FFDC16
At BRK instruction execution
External interrupt
(active edge selectable)
External interrupt
(active edge selectable)
External interrupt
(falling valid)
Valid when A-D conversion interrupt
is selected
Non-maskable software interrupt
Notes 1: Vector addresses contain interrupt jump destination addresses.
2: Reset function in the same way as an interrupt with the highest priority.
17
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
n.
atio
ific
pec ject to
s
l
ub
na
a fi are s
not
its
is is ric lim
h
T
et
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Interrupt request bit
Interrupt enable bit
Interrupt disable flag (I)
Interrupt request
BRK instruction
Reset
Fig. 13 Interrupt control
b7
b0
Interrupt edge selection register
(INTEDGE : address 003A16)
INT0 interrupt edge selection bit
INT1 interrupt edge selection bit
Not used (return “0” when read)
b7
b0
0 : Falling edge active
1 : Rising edge active
Interrupt request register 1
(IREQ1 : address 003C16)
b7
INT0 interrupt request bit
INT1 interrupt request bit
Serial I/O receive interrupt request bit
Serial I/O transmit interrupt request bit
Timer X interrupt request bit
Timer Y interrupt request bit
Timer 2 interrupt request bit
Timer 3 interrupt request bit
b7
b0
INT0 interrupt enable bit
INT1 interrupt enable bit
Serial I/O receive interrupt enable bit
Serial I/O transmit interrupt enable bit
Timer X interrupt enable bit
Timer Y interrupt enable bit
Timer 2 interrupt enable bit
Timer 3 interrupt enable bit
Interrupt request register 2
(IREQ2 : address 003D16)
CNTR0 interrupt request bit
CNTR1 interrupt request bit
Timer 1 interrupt request bit
Not used (returns “0” when read)
Key input interrupt request bit
AD conversion interrupt request bit
Not used (returns “0” when read)
0 : No interrupt request issued
1 : Interrupt request issued
b7
Interrupt control register 1
(ICON1 : address 003E16)
b0
b0
Interrupt control register 2
(ICON2 : address 003F16)
CNT R0 interrupt enable bit
CNT R1 interrupt enable bit
Timer 1 interrupt enable bit
Not used (returns “0” when read)
(Do not write “1” to this bit)
Key input interrupt enable bit
AD conversion interrupt enable bit
Not used (returns “0” when read)
(Do not write “1” to this bit)
0 : Interrupts disabled
1 : Interrupts enabled
Fig. 14 Structure of interrupt-related registers
18
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Key Input Interrupt (Key-on Wake-Up)
A key input interrupt request is generated by applying “L” level to any
pin of port P2 that have been set to input mode. In other words, it is
generated when AND of input level goes from “1” to “0”. An example
Port PXx
“L” level output
✽
of using a key input interrupt is shown in Figure 15, where an interrupt request is generated by pressing one of the keys consisted as
an active-low key matrix which inputs to ports P20–P23.
PULL register A
Bit 2 = “1”
Key input control register = “1”
Port P27 direction
register = “1”
✽✽
Port P27
latch
Key input interrupt request
P27 output
✽
Key input control register = “1”
Port P26 direction
register = “1”
✽✽
Port P26
latch
P26 output
✽
Key input control register = “1”
Port P25 direction
register = “1”
✽✽
Port P25
latch
P25 output
✽
Key input control register = “1”
Port P24 direction
register = “1”
✽✽
Port P24
latch
P24 output
✽
P23 input
✽
P22 input
✽
P21 input
✽
P20 input
Key input control register = “1”
Port P23 direction
register = “0”
✽✽
Port P23
latch
Port P2
Input reading circuit
Key input control register = “1”
Port P22 direction
register = “0”
✽✽
Port P22
latch
Key input control register = “1”
Port P21 direction
register = “0”
✽✽
Port P21
latch
Key input control register = “1”
Port P20 direction
register = “0”
Port P20
✽✽
latch
✽ P-channel transistor for pull-up
✽✽ CMOS output buffer
Fig. 15 Connection example when using key input interrupt and port P2 block diagram
19
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
n.
atio
ific
pec ject to
s
l
ub
na
a fi are s
not
its
is is ric lim
h
T
et
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
TIMERS
is set to “1”.
Read and write operation on 16-bit timer must be performed for both
high and low-order bytes. When reading a 16-bit timer, read the highorder byte first. When writing to a 16-bit timer, write the low-order
byte first. The 16-bit timer cannot perform the correct operation when
reading during the write operation, or when writing during the read
operation.
The 38C8 group has five timers: timer X, timer Y, timer 1, timer 2, and
timer 3. Timer X and timer Y are 16-bit timers, and timer 1, timer 2,
and timer 3 are 8-bit timers.
All timers are down count timers. When the timer reaches “0016”, an
underflow occurs at the next count pulse and the corresponding timer
latch is reloaded into the timer and the count is continued. When a
timer underflows, the interrupt request bit corresponding to that timer
Data bus
f(XIN)/16
(f(XCIN)/16 in low-speed mode✽)
f(XIN)
“00”,“11”
f(XCIN)
Timer X count source
“1” selection bit
“0 ”
“01”
Timer X operating
CNTR0 active
mode bits
edge switch bit
“0 ”
P42/CNTR0/BEEP+
Timer X operating
mode bits
Timer X write control bit
Timer X stop control bit
“00”,“01”,“11”
Timer X (low) latch (8)
Timer X (high) latch (8)
Timer X (low) (8)
Timer X (high) (8)
Timer X interrupt
request
“10”
“1 ”
Pulse width
measurement
mode
CNTR0 active
edge switch bit
CNTR0 interrupt
request
Pulse output mode
“0”
S
Q
“1 ”
P42 direction register
Timer Y operating mode bits
T
“00”,“01”,“10”
Q
Pulse width HL continuously
measurement mode
P42 latch
Rising edge detection
Buzzer output mode
CNTR1 interrupt
request
“11”
Period measurement mode
Falling edge detection
f(XIN)/16
(f(XCIN)/16 in low-speed mode✽)
Timer Y stop
control bit
CNTR1 active
edge switch bit
“00”,“01”,“11”
Timer Y (low) latch (8)
Timer Y (low) high (8)
Timer Y (low) (8)
Timer Y (high) (8)
“0”
P43/CNTR1/BEEP-
Timer Y interrupt
request
“10” Timer Y operating
“1 ”
mode bits
P43 direction register
P43 latch
BEEP- valid bit
f(XIN)/16
(f(XCIN)/16 in low-speed mode✽)
Timer 1 count source
selection bit “0”
Timer 1 latch (8)
Timer 2 (8)
“1”
Timer 1 interrupt
request
Timer 2 latch (8)
“0 ”
Timer 1 (8)
f(XCIN)/32
Timer 2 write control bit
Timer 2 count source
selection bit
“1 ”
Timer 2 interrupt
request
f(XIN)/16
(f(XCIN)/16 in low-speed mode✽)
“0 ”
Timer 3 latch (8)
Timer 3 (8)
f(XCIN)/32
“1”
Timer 3 count source
selection bit
✽ Internal clock φ = XCIN divided by 2 in low-speed mode
Fig. 16 Timer block diagram
20
Timer 3 interrupt
request
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Timer X
Timer X is a 16-bit timer that can be selected in one of four modes
and can be controlled the timer X write by setting the timer X mode
register.
(1) Timer Mode
When the timer X count source selection bit is “0”, the timer counts
f(X IN)/16 (or f(XCIN)/16 in low-speed mode). When it is “1”, the timer
counts f(XIN).
(2) Buzzer Output Mode
Each time the timer underflows, a signal output from the BEEP+ pin
is inverted. When the BEEP- valid bit is “1”, the opposite phase of
BEEP+ signal is output from the BEEP- pin. When using the BEEP+
pin and the BEEP- pin, set ports shared with these pins to output.
(3) Event Counter Mode
The timer counts signals input through the CNTR0 pin.
Except for this, the operation in event counter mode is the same as
in timer mode. When using a timer in this mode, set the port shared
with the CNTR0 pin to input.
(4) Pulse Width Measurement Mode
When the timer X count source selection bit is “0”, the count source
is f(X IN)/16 (or f(X CIN)/16 in low-speed mode). When it is “1”, the
count source is f(XIN).
If CNTR 0 active edge switch bit is “0”, the timer counts while the
input signal of CNTR 0 pin is at “H”. If it is “1”, the timer counts while
the input signal of CNTR 0 pin is at “L”. When using a timer in this
mode, set the port shared with the CNTR0 pin to input.
b7
b0
Timer X mode register
(TXM : address 002716)
Timer X write control bit
0 : Write value in latch and counter
1 : Write value in latch only
BEEP- valid bit
0 : Invalid
1 : Valid
Not used
Timer X operating mode bits
b5 b4
0 0 : Timer mode
0 1 : Buzzer output mode
1 0 : Event counter mode
1 1 : Pulse width measurement mode
CNT R0 active edge switch bit
0 : Count at rising edge in event counter mode
Start from “H” output in pulse output mode
Measure “H” pulse width in pulse width
measurement mode
Falling edge active for interrupt
1 : Count at falling edge in event counter mode
Start from “L” output in pulse output mode
Measure “L” pulse width in pulse width
measurement mode
Rising edge active for interrupt
Timer X stop control bit
0 : Count start
1 : Count stop
Fig. 17 Structure of timer X mode register
●Timer X write control
If the timer X write control bit is “0”, when the value is written in the
address of timer X, the value is loaded in the timer X and the latch
at the same time.
If the timer X write control bit is “1”, when the value is written in the
address of timer X, the value is loaded only in the latch. The value
in the latch is loaded in timer X after timer X underflows.
If the value is written in latch only, unexpected value may be set in
the high-order counter when the writing in high-order latch and the
underflow of timer X are performed at the same timing.
■Notes on CNTR0 interrupt active edge selection
CNTR 0 interrupt active edge depends on the CNTR 0 active edge
switch bit.
21
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
n.
atio
ific
pec ject to
s
l
ub
na
a fi are s
not
its
is is ric lim
h
T
et
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
Timer Y
Timer Y is a 16-bit timer that can be selected in one of four modes.
(1) Timer Mode
The timer counts f(XIN)/16 (or f(X CIN)/16 in low-speed mode).
(2) Period Measurement Mode
CNTR1 interrupt request is generated at rising/falling edge of CNTR1
pin input signal. Simultaneously, the value in timer Y latch is reloaded
in timer Y and timer Y continues counting down. Except for the abovementioned, the operation in period measurement mode is the same
as in timer mode.
The timer value just before the reloading at rising/falling of CNTR1
pin input signal is retained until the timer Y is read once after the
reload.
The rising/falling timing of CNTR1 pin input signal is found by CNTR1
interrupt. When using a timer in this mode, set the port shared with
the CNTR1 pin to input.
(3) Event Counter Mode
The timer counts signals input through the CNTR1 pin.
Except for this, the operation in event counter mode is the same as
in timer mode. When using a timer in this mode, set the port shared
with the CNTR1 pin to input.
(4) Pulse Width HL Continuously Measurement
Mode
CNTR1 interrupt request is generated at both rising and falling edges
of CNTR 1 pin input signal. Except for this, the operation in pulse
width HL continuously measurement mode is the same as in period
measurement mode. When using a timer in this mode, set the port
shared with the CNTR 1 pin to input.
■Notes on CNTR1 interrupt active edge selection
CNTR 1 interrupt active edge depends on the CNTR1 active edge
switch bit. However, in the pulse width HL continuously measurement mode, CNTR 1 interrupt request is generated at both rising and
falling edges of CNTR1 pin input signal regardless of the setting of
CNTR 1 active edge switch bit.
22
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
b7
b0
Timer Y mode register
(TYM : address 002816)
Timer X count source selection bit
0 : f(XIN)/16 (f(XCIN)/16 in low-speed mode✽)
1 : f(XIN)
Not used (return “0” when read)
Timer Y operating mode bits
b5 b4
0 0 : Timer mode
0 1 : Period measurement mode
1 0 : Event counter mode
1 1 : Pulse width HL continuously
measurement mode
CNT R1 active edge switch bit
0 : Count at rising edge in event counter mode
Measure the falling edge to falling edge
period in period measurement mode
Interrupt falling edge active
1 : Count at falling edge in event counter mode
Measure the rising edge period in period
measurement mode
Interrupt rising edge active
Timer Y stop control bit
0 : Count start
1 : Count stop
✽ Internal clock φ in low-speed mode is XCIN divided by 2.
When the timer X operating mode bits are “00” or “11”, the timer X count source is
f(XCIN)/16. When the timer X operating mode bits are “01”, the timer X count source
is f(XCIN).
Fig. 18 Structure of timer Y mode register
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Timer 1, Timer 2, Timer 3
Timer 1, timer 2, and timer 3 are 8-bit timers. The count source for
each timer can be selected by the timer 123 mode register. The timer
latch value is not affected by a change of the count source. However,
because changing the count source may cause an inadvertent count
down of the timer. Therefore, rewrite the value of timer whenever the
count source is changed.
●Timer 2 write control
If the timer 2 write control bit is “0”, when the value is written in the
address of timer 2, the value is loaded in the timer 2 and the latch at
the same time.
If the timer 2 write control bit is “1”, when the value is written in the
address of timer 2, the value is loaded only in the latch. The value in
the latch is loaded in timer 2 after timer 2 underflows.
■Notes on timer 1 to timer 3
When the count source of timer 1 to 3 is changed, the timer counting
value may be changed large because a thin pulse is generated in
count input of timer. If timer 1 output is selected as the count source
of timer 2 or timer 3, when timer 1 is written, the counting value of
timer 2 or timer 3 may be changed large because a thin pulse is
generated in timer 1 output.
Therefore, set the value of timer in the order of timer 1, timer 2 and
timer 3 after the count source selection of timer 1 to 3.
b7
b0
Timer 123 mode register
(T123M :address 002916)
Not used
Timer 2 write control bit
0 : Write data in latch and counter
1 : Write data in latch only
Timer 2 count source selection bit
0 : Timer 1 output
1 : f(XIN)/16
(or f(XCIN)/16 in low-speed mode*)
Timer 3 count source selection bit
0 : Timer 1 output
1 : f(XCIN)/32
Timer 1 count source selection bit
0 : f(XIN)/16
(or f(XCIN)/16 in low-speed mode*)
1 : f(XCIN)/32
Not used (return “0” when read)
* Internal clock φ is XCIN/2 in the low-speed mode.
Fig. 19 Structure of timer 123 mode register
23
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
n.
atio
ific
pec ject to
s
l
ub
na
a fi are s
not
its
is is ric lim
h
T
et
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
SERIAL I/O
(1) Clock Synchronous Serial I/O Mode
Serial I/O can be used as either clock synchronous or asynchronous
(UART) serial I/O. A dedicated timer (baud rate generator) is also
provided for baud rate generation.
Clock synchronous serial I/O can be selected by setting the mode
selection bit of the serial I/O control register to “1”.
For clock synchronous serial I/O, the transmitter and the receiver
must use the same clock. If an internal clock is used, transfer is started
by a write signal to the transmit/receive buffer registers.
Data bus
Receive buffer full flag (RBF)
Receive buffer register
Receive interrupt request (RI)
Receive shift register
P44/RXD
Address 001A16
Serial I/O control register
Address 001816
Shift clock
Clock control circuit
P46/SCLK
Serial I/O
clock selection bit
Frequency division ratio 1/(n+1)
BRG count source selection bit
f(XIN)
(f(XCIN) in low-speed mode)
1/4
P47/SRDY
F/F
Address 001C16
Clock control circuit
Falling-edge detector
Shift clock
P45/TXD
1/4
Baud rate generator
Transmit shift register
Transmit shift register shift completion flag (TSC)
Transmit interrupt source selection bit
Transmit interrupt request (TI)
Transmit buffer register
Address 001816
Transmit buffer empty flag (TBE)
Address 001916
Serial I/O status register
Data bus
Fig. 20 Block diagram of clock synchronous serial I/O
Transmit/receive shift clock
(1/2 to 1/2048 of internal clock,
or an external clock)
Serial output TXD
D0
D1
D2
D3
D4
D5
D6
D7
Serial input RXD
D0
D1
D2
D3
D4
D5
D6
D7
Receive enable signal SRDY
Write signal to receive/transmit
buffer register (address 001816)
TBE = 0
TBE = 1
TSC = 0
RBF = 1
TSC = 1
Overrun error (OE)
detection
Notes 1: The transmit interrupt (TI) can be selected to occur either when the transmit buffer register has emptied (TBE=1) or after
the transmit shift operation has ended (TSC=1), by setting the transmit interrupt source selection bit (TIC) of the serial
I/O control register.
2: If data is written to the transmit buffer register when TSC=0, the transmit clock is generated continuously and serial data
is output continuously from the TXD pin.
3: The receive interrupt (RI) is set when the receive buffer full flag (RBF) becomes “1” .
Fig. 21 Operation of clock synchronous serial I/O function
24
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
(2) Asynchronous Serial I/O (UART) Mode
but the two buffers have the same address in memory. Since the shift
register cannot be written to or read from directly, transmit data is
written to the transmit buffer, and receive data is read from the receive buffer.
The transmit buffer can also hold the next data to be transmitted, and
the receive buffer register can hold a character while the next character is being received.
Clock asynchronous serial I/O mode (UART) can be selected by clearing the serial I/O mode selection bit of the serial I/O control register
to “0”.
Eight serial data transfer formats can be selected, and the transfer
formats used by a transmitter and receiver must be identical.
The transmit and receive shift registers each have a buffer register,
Data bus
Address 001816
P44/RXD
Serial I/O control register
Address 001A16
Receive buffer full flag (RBF)
Receive interrupt request (RI)
Receive buffer register
OE
Character length selection bit
STdetector
7 bits
Receive shift register
1/16
8 bits
PE FE
UART control register
Address 001B16
SP detector
Clock control circuit
Serial I/O clock selection bit
P46/SCLK
BRG count source selection bit
Frequency division ratio 1/(n+1)
f(XIN)
Baud rate generator
Address 001C16
1/4
ST/SP/PA generator
Transmit shift register shift completion flag (TSC)
1/16
Transmit shift register
P45/TXD
Character length selection bit
Transmit buffer register
Address 001816
Transmit interrupt source selection bit
Transmit interrupt request (TI)
Transmit buffer empty flag (TBE)
Serial I/O status register Address 001916
Data bus
Fig. 22 Block diagram of UART serial I/O
Transmit or receive clock
Transmit buffer write signal
TBE=0
TSC=0
TBE=1
Serial output TXD
TBE=0
TSC=1✽
TBE=1
ST
D0
D1
SP
ST
D0
1 start bit
7 or 8 data bits
1 or 0 parity bit
1 or 2 stop bit (s)
Receive buffer read signal
✽Generated
RBF=0
RBF=1
Serial input RXD
ST
D0
D1
D1
SP
ST
D0
D1
SP
at 2nd bit in 2-stop-bit mode
RBF=1
SP
Notes 1: Error flag detection occurs at the same time that the RBF flag becomes “1” (at 1st stop bit, during reception).
2: The transmit interrupt (TI) can be selected to occur when either the T BE or TSC flag becomes “1” by the setting of the transmit interrupt source
selection bit (TIC) of the serial I/O control register.
3: The receive interrupt (RI) is set when the RBF flag becomes “1”.
4: After data is written to the transmit buffer register when TSC=1, 0.5 to 1.5 cycles of the data shift cycle is necessary until changing to TSC=0.
Fig. 23 Operation of UART serial I/O function
25
RY
A
N
I
n.
atio
ific
pec ject to
s
l
ub
na
a fi are s
not
its
is is ric lim
h
T
et
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
[Transmit Buffer/Receive Buffer Register
(TB/RB)] 001816
The transmit buffer register and the receive buffer register are located at the same address. The transmit buffer register is write-only
and the receive buffer register is read-only. If a character bit length is
7 bits, the MSB of data stored in the receive buffer register is “0”.
[Serial I/O Status Register (SIOSTS)] 001916
The read-only serial I/O status register consists of seven flags (bits 0
to 6) which indicate the operating status of the serial I/O function and
various errors.
Three of the flags (bits 4 to 6) are valid only in UART mode.
The receive buffer full flag (bit 1) is cleared to “0” when the receive
buffer is read.
If there is an error, it is detected at the same time that data is transferred from the receive shift register to the receive buffer register,
and the receive buffer full flag is set. A write to the serial I/O status
register clears all the error flags OE, PE, FE, and SE. Writing “0” to
the serial I/O enable bit (SIOE) also clears all the status flags, including the error flags.
All bits of the serial I/O status register are initialized to “0” at reset,
but if the transmit enable bit (bit 4) of the serial I/O control register
has been set to “1”, the transmit shift register shift completion flag
(bit 2) and the transmit buffer empty flag (bit 0) become “1”.
[Serial I/O Control Register (SIOCON)] 001A16
The serial I/O control register contains eight control bits for the serial
I/O1 function.
[UART Control Register (UARTCON) ]001B16
This is a 5 bit register containing four control bits, which are valid
when UART is selected and set the data format of an data receiver/
transfer, and one control bit, which is always valid and sets the output structure of the P45/T XD pin.
[Baud Rate Generator(BRG)] 001616
The baud rate generator determines the baud rate for serial transfer.
The baud rate generator divides the frequency of the count source
by 1/(n + 1), where n is the value written to the baud rate generator.
26
MITSUBISHI MICROCOMPUTERS
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
■Notes on serial I/O
When setting the transmit enable bit to “1”, the serial I/O transmit
interrupt request bit is automatically set to “1”. When not requiring
the interrupt occurrence synchronized with the transmission enalbed,
take the following sequence.
➀Set the serial I/O transmit interrupt enable bit to “0” (disabled).
➁Set the transmit enable bit to “1”.
➂Set the serial I/O transmit interrupt request bit to “0” after 1 or more
instructions have been executed.
➃Set the serial I/O transmit interrupt enable bit to “1” (enabled).
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
b7
b7
IM
b0
Serial I/O status register
(SIOSTS : address 001916)
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
b7
b0
Serial I/O control register
(SIOCON : address 001A16)
Transmit buffer empty flag (TBE)
0: Buffer full
1: Buffer empty
BRG count source selection bit (CSS)
0: f(XIN) (f(XCIN) in low-speed mode)
1: f(XIN)/4 (f(XCIN)/4 in low-speed mode)
Receive buffer full flag (RBF)
0: Buffer empty
1: Buffer full
Transmit shift register shift completion flag (TSC)
0: Transmit shift in progress
1: Transmit shift completed
Serial I/O synchronous clock selection bit (SCS)
0: BRG output divided by 4 when clock synchronous serial
I/O is selected.
BRG output divided by 16 when UART is selected.
1: External clock input when clock synchronous serial I/O is
selected.
External clock input divided by 16 when UART is selected.
Overrun error flag (OE)
0: No error
1: Overrun error
SRDY output enable bit (SRDY)
0: P47 pin operates as ordinary I/O pin.
1: P47 pin operates as SRDY output pin.
Parity error flag (PE)
0: No error
1: Parity error
Transmit interrupt source selection bit (TIC)
0: Interrupt when transmit buffer has emptied
1: Interrupt when transmit shift operation is completed
Framing error flag (FE)
0: No error
1: Framing error
Transmit enable bit (TE)
0: Transmit disabled
1: Transmit enabled
Summing error flag (SE)
0: OE U PE U F E =0
1: OE U PE U F E =1
Receive enable bit (RE)
0: Receive disabled
1: Receive enabled
Not used (returns “1” when read)
Serial I/O mode selection bit (SIOM)
0: Asynchronous serial I/O (UART)
1: Clock synchronous serial I/O
b0 UART control regi ster
(UART CON : address 001B16)
Character length selection bit (CHAS)
0: 8 bits
1: 7 bits
Serial I/O enable bit (SIOE)
0: Serial I/O disabled
(pins P44–P47 operate as ordinary I/O pins)
1: Serial I/O enabled
(pins P44–P47 operate as serial I/O pins)
Parity enable bit (PARE)
0: Parity checking disabled
1: Parity checking enabled
Parity selection bit (PARS)
0: Even parity
1: Odd parity
Stop bit length selection bit (ST PS)
0: 1 stop bit
1: 2 stop bits
P45/TXD P-channel output disable bit (POFF)
0: CMOS output (in output mode)
1: N-channel open-drain output (in output mode)
Not used (return “1” when read)
Fig. 24 Structure of serial I/O control registers
27
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
n.
atio
ific
pec ject to
s
l
ub
na
a fi are s
not
its
is is ric lim
h
T
et
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
A-D CONVERTER
[A-D Conversion Registers (ADL, ADH)] 003216,
003316
The A-D conversion registers are read-only registers that contain the
result of an A-D conversion. During A-D conversion, do not read these
registers.
Resistor ladder
The resistor ladder outputs the comparison voltage by dividing the
voltage between VDD and VSS by resistance.
Channel Selector
The channel selector selects one of the ports P33/AIN3–P3 0/AIN0 and
ports P10/A IN4–P1 3/AIN7, and inputs it to the comparator.
[A-D Control Register (ADCON)] 003116
The A-D control register controls the A-D conversion process. Bits 0
to 2 are analog input pin selection bits. Bit 3 is an A-D conversion
completion bit and “0” during A-D conversion, then changes to “1”
when the A-D conversion is completed. Writing “0” to this bit starts
the A-D conversion. When bit 5, which is the AD external trigger valid
bit, is set to “1”, A-D conversion is started even by a rising edge or
falling edge of an ADT input.
b7
b0
A-D control register
(ADCON : address 003116)
Analog input pin selection bits
0 0 0 : P30/AIN0
0 0 1 : P31/AIN1
0 1 0 : P32/AIN2
0 1 1 : P33/AIN3
1 0 0 : P10/AIN4
1 0 1 : P11/AIN5
1 1 0 : P12/AIN6
1 1 1 : P13/AIN7
Comparator and Control Circuit
AD conversion completion bit
0 : Conversion in progress
1 : Conversion completed
The comparator and control circuit compares an analog input voltage with the comparison voltage and stores the result in the A-D
conversion register. When an A-D conversion is completed, the control circuit sets the AD conversion completion bit and the AD interrupt
request bit to “1”.
Because the comparator consists of a capacitor coupling, a deficient
conversion speed may cause lack of electric charge and make the
conversion accuracy worse. When A-D conversion is performed in
the middle-speed mode or the high-speed mode, set f(XIN) to at least
500 kHz.
In the low-speed mode, A-D conversion is performed by using the
built-in self-oscillation circuit. Therefore, there is no limitation in
the lower bound frequency of f(XIN ).
Not used (return “0” when read)
AD external trigger valid bit
0 : A-D external trigger invalid
1 : A-D external trigger valid
Not used (return “0” when read)
•8-bit read (Read only address 003216.)
b0
b7
A-D conversion register (low-order)
(ADL: Address 003216)
b9 b8 b7 b6 b5 b4 b3 b2
•10-bit read (Read address 003316 first.)
b0
b7
A-D conversion register (high-order)
(ADH: Address 003316)
b9 b8
A-D conversion register (low-order)
(ADL: Address 003216)
b7 b6 b5 b4 b3 b2 b1 b0
b0
b7
Trigger Start
Note: High-order 6 bits of address 003316 becomes “0” at reading.
When using the A-D external trigger, set the port shared with the
ADT pin to input. The polarity of INT1 interrupt edge also applies to
the A-D external trigger. When the INT1 interrupt edge polarity is
switched after an external trigger is validated, an A-D conversion
may be started.
Fig. 25 Structure of A-D control register
Data bus
b0
b7
A-D control register
P41/INT1/ADT
3
A-D control circuit
Channel selector
P30/AIN0
P31/AIN1
P32/AIN2
P33/AIN3
P10/AIN4
P11/AIN5
P12/AIN6
P13/AIN7
(H)
Comparater
28
(L)
A-D conversion register A-D conversion register
10
Resistor ladder
VSS
Fig. 26 A-D converter block diagram
A-D interrupt request
VCC
Bit
84
SEG58
133
SEG9
SEG8
Segment driver
134
14 15
Bit selector
7 8
Segment driver
0 1
Segment driver
14 15
Bit
14 15
Bit selector
7 8
SEG59
83
Segment driver
0 1
L M2
VL5
11
Voltage
multiplier
VL2
C1
C3
9
LCD control register 1
(address 003716)
LCD control register 2
(address 003816)
5
COM0 COM1
6
74
142
141
73
Common/Segment
driver
f(XCIN)/16
f(XIN)/1024
COM15 COM16/ COM17/ COM31/
SEG60
SEG1
SEG0
Common driver
“0”
“1”
Timing controller
LCDCK
LCD clock
generator
LC27 LC26 LC25 LC24 LC23 LC22 LC21 LC20
LC17 LC16 LC15 LC14 LC13 LC12 LC11 LC10
VL4
L M0
13
15
12 C2 14 VLIN
7
L M1
10 VL3 8 VL1
Bias controller
L M3
The 38C8 group has the built-in Liquid Crystal Display (LCD)
controller/driver consisting of the following.
●240-byte LCD display RAM
●52 or 68 segment driver
●16 or 32 common driver
●LCD clock generator
●Timing controller
Bit selector
7 8
008316, 00C716
or
038316, 03C716
L M4
LCD CONTROLLER/DRIVER
Bit selector
14 15 0 1
Bit
7 8
Bit
0 1
008216, 00C616
or
038216, 03C616
L M5
IM
004116, 008516
or
034116, 038516
L M6
LCD mode register
(address 003916)
L
PRE
004016, 008416
or
034016, 038416
LCD display RAM
L M7
Data bus
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
RY
A
N
I
MITSUBISHI MICROCOMPUTERS
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
●Bias controller
●Voltage multiplier
●LCD mode register
●LCD control registers 1, 2
A maximum of 68 segment output pins and 32 common output pins
can be used for control of external LCD display.
Fig. 27 Block diagram of LCD controller/driver
29
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
n.
atio
ific
pec ject to
s
l
ub
na
a fi are s
not
its
is is ric lim
h
T
et
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 7 Maximum number of display pixels at each duty ratio
LCD Controller/Driver Function
Duty ratio
The controller/driver performs the bias control and the time sharing
control by the LCD control registers 1, 2 (LC1, LC2), and the LCD
mode register (LM). The data of corresponding LCDRAM is output
from the segment pins according to the output timing of the common
pins.
The 38C8 group has the voltage multiplier only for LCD in addition to
LCD controller/driver .
16
32
Maximum number of display pixel
16 ✕ 68 dots
(5 ✕ 7 dots + cursor 2 lines)
32 ✕ 52 dots
(5 ✕ 7 dots + cursor 4 lines)
Note: When executing the STP instruction while operating LCD, execute the STP instruction after prohibiting LCD (set “0” to bit 3
of the LCD mode regsiter).
[LCD mode register (LM)] 003916
The LCD mode register is used for setting the LCD controller/driver
according to the LCD panel used.
[LCD control register 1 (LC1)] 003716
The LCD control register 1 controls the voltage multiplier and built-in
resistance.
[LCD control register 2 (LC2)] 003816
The LCD control register 2 is read-only. Setting “1” to bit 5 makes
built-in resistance low resistance, and can raise drivability of the segment pins and the common pins.
b7
b0
b7
LCD control register 1
(LC1: address 003716)
Not used
(Do not write “1” to these bits.)
Drivability selection bit 1
0 : Normal (Drivability selection
bit 2 valid)
1 : Restraint (Note 1)
Not used
(Do not write “1” to this bit.)
Voltage multiplier enable bit
0 : Voltage multiplier stop
1 : Voltage multiplier operating
Note 1: Consumption current can be reduced by restraint of drivability. But
an irregular display might be caused according to the panel or the
display pattern.
b7
b0
LCD control register 2
(LC2: address 003816)
Not used (Do not write “1” to these bits.)
Drivability selection bit 2
0 : Normal
1 : Reinforcing (Note 2)
Not used (Do not write “1” to these bits.)
Note 2: The drive of a more large-scale LCD panel becomes easy by setting “1”
to this bit. But consumption current is increased at LCD drive. When
the drivability selection bit 1 is “1”, this function is invaid.
Fig. 28 Structure of LCD control register
30
b0
LCD mode register
(LM: address 003916)
Duty ratio selsection bit✽
1 : 32 duty (use COM0–COM31)
0 : 16 duty (use COM0–COM15)
Not used
(Do not write “0” to this bit.)
LCD display RAM address selection bit
0 : 3 page
1 : 0 page
LCD enable bit
0 : LCD OFF
1 : LCD ON
LCD drive timing selection bit
0 : A type
1 : B type
LCDCK division ratio selection bits
b6 b5
0 0 : Clock input
0 1 : 2 division of clock input
1 0 : 4 division of clock input
1 1 : 8 division of clock input
LCDCK count source selection bit (Note 3)
0 : f(XIN)/1024
1 : f(XCIN)/16
Note 3: LCDCK is a clock for a LCD timing controller.
Internal clock φ is XCIN divided by 2 in the low-speed mode.
✽ When selecting 32 duty, functions of pins 130 to 142 become COM16 to COM23,
and functions of pins 75 to 82 become COM24 to COM31.
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Voltage Multiplier
Table 8 Bias control and applied voltage to VL1–VL5
When the voltage multiplier is operated after a reference voltage for
boosting is applied to LCD power supply VLIN, a voltage that is three
times as large as VLIN pin occurs at the VL5 pin. Operate the voltage
multiplier after applying a reference voltage for boosting to VLIN.
Bias value
1/7 bias
Bias Control
In the LCD power source pins (VL1 –VL5), a proper level is automatically generated in 1/32 and 1/16 duty ratio. The quality of the LCD
display can be stabilized by connecting the capacitor for smoothness between Vss and these pins.
1/5 bias
Voltage value
VL5 = VLCD
VL4 = 6/7 VLCD
VL3 = 5/7 VLCD
VL2 = 2/7 VLCD
VL1 = 1/7 VLCD
VL5 = VLCD
VL4 = 4/5 VLCD
VL3 = 3/5 VLCD
VL2 = 2/5 VLCD
VL1 = 1/5 VLCD
Note: VLCD is a value which can be supplied to the LCD panel. Set value
which is less than maximum ratings to VLCD.
RT
RT
VL5
VL5
VL5
VL4
VL3
VL4
VL3
VL4
VL3
VL2
VL2
VL2
VL1
VL1
VL1
C3
C3
C3
C2
C2
C2
C1
VLIN
C1
VLIN
C1
VLIN
1.3 to
2.33 V
1/5, 1/7 bias
When using voltage multiplier
circuit
1/5, 1/7 bias
When not using voltage
multiplier circuit (1)
R1
R2
R3
R4
R5
•At 1/5 bias
R1=R2=R3=R4=R5
•At 1/7 bias
R1=R2=R4=R5
R3=3•R1
1/5, 1/7 bias
When not using voltage
multiplier circuit (2)
Fig. 29 Example of circuit at each bias
31
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
n.
atio
ific
pec ject to
s
l
ub
na
a fi are s
not
its
is is ric lim
h
T
et
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Common Pin and Duty Ratio Control
LCD Drive Timing
The common pins (COM0–COM 31) to be used are determined by
duty ratio.
Select duty ratio by the duty ratio selection bit (bit 0 of the LCD mode
register).
The LCDCK timing frequency (LCD drive timing) is generated internally and the frame frequency can be determined with the following
equation;
f(LCDCK) =
Table 9 Duty ratio control and common pins used
Duty
ratio
Duty ratio
selection bit
16
0
COM 0–COM15 (Note)
32
1
COM0–COM31
Common pins used
(frequency of count source for LCDCK)
(divider division ratio for LCD)
f(LCDCK)
Frame frequency = (duty ratio)
Note: The SEG0 /COM16 –SEG7/COM 23 pins are used as the SEG 0–SEG7 .
The SEG67/COM24–SEG60/COM31 pins are used as the SEG67–SEG60.
LCD Display RAM
SEG44
SEG45
SEG46
SEG47
SEG48
SEG49
SEG50
SEG51
SEG52
SEG53
SEG54
SEG55
SEG56
SEG57
SEG58
SEG59
SEG60
SEG61
SEG62
SEG63
SEG64
SEG65
SEG66
SEG67
SEG0
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
SEG19
SEG20
SEG21
SEG22
SEG23
Addresses 004016 to 012F16 is the designated RAM for the LCD
display. When “1” are written to these addresses, the corresponding
segments of the LCD display panel are turned on.
COM0
0 0 0 0 0 0 0 0 1 0 0 0 1 0 1 1 1 0 1 1 1 1 1 0
0 0 1 1 1 0 0 1 0 0 0 1 0 1 1 1 0 0 0 0 0 0 0 0 LSB
COM1
0 0 0 0 0 0 0 0 1 1 0 1 1 0 0 1 0 0 0 0 1 0 0 0
0 1 0 0 0 1 0 1 0 0 0 1 0 0 1 0 0 0 0 0 0 0 0 0
COM2
COM3
0 0 0 0 0 0 0 0 1 0 1 0 1 0 0 1 0 0 0 0 1 0 0 0
0 0 0 0 0 0 0 0 1 0 0 0 1 0 0 1 0 0 0 0 1 0 0 0
0 1 0 0 0 0 0 1 0 0 0 1 0 0 1 0 0 0 0 0 0 0 0 0
0 0 1 1 1 0 0 1 1 1 1 1 0 0 1 0 0 0 0 0 0 0 0 0
COM4
COM5
0 0 0 0 0 0 0 0 1 0 0 0 1 0 0 1 0 0 0 0 1 0 0 0
0 0 0 0 0 0 0 0 1 0 0 0 1 0 0 1 0 0 0 0 1 0 0 0
0 0 0 0 0 1 0 1 0 0 0 1 0 0 1 0 0 0 0 0 0 0 0 0
0 1 0 0 0 1 0 1 0 0 0 1 0 0 1 0 0 0 0 0 0 0 0 0
COM6
0 0 0 0 0 0 0 0 1 0 0 0 1 0 1 1 1 0 0 0 1 0 0 0
0 0 1 1 1 0 0 1 0 0 0 1 0 1 1 1 0 0 0 0 0 0 0 0
COM7
COM8
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 MSB
COM9
0 1 0 0 0 1 0 1 1 1 1 1 0 0 1 1 1 0 0 0 1 1 1 0
0 1 1 0 1 1 0 0 0 0 1 0 0 1 0 0 0 1 0 1 0 0 0 1
1 1 1 1 1 0 1 1 1 1 1 0 1 1 1 1 1 0 1 1 1 1 0 0 LSB
1 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 1 0
COM10
0 1 0 1 0 1 0 0 0 1 0 0 0 1 0 0 0 1 0 1 0 0 0 0
1 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 1 0
COM11
0 1 0 0 0 1 0 0 0 0 1 0 0 0 1 1 1 0 0 1 0 0 0 0
0 1 0 0 0 1 0 0 0 0 0 1 0 1 0 0 0 1 0 1 0 0 0 0
1 1 1 1 0 0 1 1 1 1 0 0 1 1 1 1 0 0 1 1 1 1 0 0
1 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0 0
COM14
0 1 0 0 0 1 0 1 0 0 0 1 0 1 0 0 0 1 0 1 0 0 0 1
0 1 0 0 0 1 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0
1 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0 0
1 1 1 1 1 0 1 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0 0
COM15
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
COM16
COM17
0 0 1 0 0 0 1 0 1 1 1 1 1 0 0 1
1 0 0 1 0 0 0 1 0 1 1 1 1 1 0 0 LSB
0 0 1 1 0 1 1 0 0 0 0 1 0 0 1 0
0 0 1 0 1 0 1 0 0 0 1 0 0 0 1 0
0 1 0 1 1 0 1 1 0 1 0 0 0 0 0 0
0 1 0 1 0 1 0 1 0 1 0 0 0 0 0 0
0 0 1 0 0 0 1 0 0 0 0 1 0 0 0 1
1 1 0 1 0 0 0 1 0 1 1 1 1 0 0 0
COM12
COM13
COM18
COM19
COM20
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 MSB
0 0 1 0 0 0 1 0 0 0 0 0 1 0 1 0
0 0 1 0 0 0 1 0 1 0 0 0 1 0 1 0
0 1 0 1 0 0 0 1 0 1 0 0 0 0 0 0
0 1 0 1 0 0 0 1 0 1 0 0 0 0 0 0
0 0 1 0 0 0 1 0 0 1 1 1 0 0 0 1
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1 0 0 1 0 0 0 1 0 1 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 MSB
COM25
0 0 0 0 0 0 0 0 0 0 1 0 0 0 1 0
0 0 0 0 0 0 0 0 0 0 1 0 0 0 1 0
1 1 1 1 1 0 1 1 1 1 0 0 0 0 0 0 LSB
1 0 0 0 0 0 1 0 0 0 1 0 0 0 0 0
COM26
COM27
0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0
0 0 0 0 0 0 1 1 1 0 0 0 1 0 0 0
1 0 0 0 0 0 1 0 0 0 1 0 0 0 0 0
1 1 1 1 0 0 1 1 1 1 0 0 0 0 0 0
COM28
0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0
1 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0
COM29
COM30
0 0 0 0 0 0 0 0 0 0 1 0 0 0 1 0
0 0 0 0 0 0 0 0 0 0 1 0 0 0 1 0
1 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0
1 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0
COM31
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 MSB
COM21
COM22
COM23
COM24
036C
036D
036E
036F
0370
0371
0372
0378
0374
0375
0376
0377
0378
0379
037A
037B
037C
037D
037E
037F
0380
0381
0382
0383
03EC
03ED
03EE
03EF
03F0
03F1
03F2
03F3
03F4
03F5
03F6
03F7
03F8
03F9
03FA
03FB
0420
0421
0422
0423
0424
0425
0426
0427
0428
0429
042A
042B
042C
042D
042E
042F
03B0
03B1
03B2
03B3
03B4
03B5
03B6
03B7
03B8
03B9
03BA
03BB
03BC
03BD
03BE
03BF
03C0
03C1
03C2
03C3
03C4
03C5
03C6
03C7
03C8
03C9
03CA
03CB
03CC
03CD
03CE
03CF
03D0
03D1
03D2
03D3
03D4
03D5
03D6
03D7
03FC
03FD
03FE
03FF
0400
0401
0402
0403
0404
0405
0406
0407
0408
0409
040A
040B
0384
0385
0386
0387
0388
0389
038A
038B
038C
038D
038E
038F
0390
0391
0392
0393
0394
0395
0396
0397
0398
0399
039A
039B
0340
0341
0342
0343
0344
0345
0346
0347
0348
0349
034A
034B
034C
034D
034E
034F
0350
0351
0352
0353
0354
0355
0356
0357
LCD display map
When selecting 3 page
32
00EC
00ED
00EE
00EF
00F0
00F1
00F2
00F3
00F4
00F5
00F6
00F7
00F8
00F9
00FA
00FB
0120
0121
0122
0123
0124
0125
0126
0127
0128
0129
012A
012B
012C
012D
012E
012F
006C
006D
006E
006F
0070
0071
0072
0073
0074
0075
0076
0077
0078
0079
007A
007B
007C
007D
007E
007F
0080
0081
0082
0083
00C8
00C9
00CA
00CB
00CC
00CD
00CE
00CF
00D0
00D1
00D2
00D3
00D4
00D5
00D6
00D7
00B0
00B1
00B2
00B3
00B4
00B5
00B6
00B7
00B8
00B9
00BA
00BB
00BC
00BD
00BE
00BF
00C0
00C1
00C2
00C3
00C4
00C5
00C6
00C7
Fig. 30 LCD display RAM map
00FC
00FD
00FE
00FF
0100
0101
0102
0103
0104
0105
0106
0107
0108
0109
010A
010B
0040
0041
0042
0043
0044
0045
0046
0047
0048
0049
004A
004B
004C
004D
004E
004F
0050
0051
0052
0053
0054
0055
0056
0057
0084
0085
0086
0087
0088
0089
008A
008B
008C
008D
008E
008F
0090
0091
0092
0093
0094
0095
0096
0097
0098
0099
009A
009B
When selecting 0 page
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
LCDCK
1 frame (16 clocks)
1 frame (16 clocks)
VL5
VL4
COM23
VL3
VL2
VL1
VSS
VL5
VL4
COM22
VL3
VL2
VL1
VSS
VL5
VL4
SEG0
VL3
VL2
VL1
VSS
VL5
VL4
VL3
VL2
VL1
SEG0 –
COM23
VSS
VL1
VL2
VL3
VL4
VL5
ON
OFF
ON
OFF
VL5
VL4
VL3
VL2
VL1
SEG0 –
COM22
VSS
VL1
VL2
VL3
VL4
VL5
OFF
OFF
Fig. 31 LCD drive waveform (1/16 duty ratio, 1/5 bias, A type)
33
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
n.
atio
ific
pec ject to
s
l
ub
na
a fi are s
not
its
is is ric lim
h
T
et
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
LCDCK
1 frame (32 clocks)
COM31
1 frame (32 clocks)
VL5
VL4
VL3
VL2
VL1
VSS
VL5
VL4
VL3
COM30
VL2
VL1
VSS
VL5
VL4
VL3
SEG0
VL2
VL1
VSS
VL5
VL4
VL3
SEG0 –
COM31
VL2
VL1
VSS
VL1
VL2
VL3
VL4
VL5
ON
OFF
ON
OFF
ON
OFF
VL5
VL4
VL3
SEG0 –
COM30
VL2
VL1
VSS
VL1
VL2
VL3
VL4
VL5
OFF
Fig. 32 LCD drive waveform (1/32 duty ratio, 1/7 bias, B type)
34
OFF
OFF
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
RESET CIRCUIT
To reset the microcomputer, RESET pin should be held at an “L”
level for 2 µs or more. Then the RESET pin is returned to an “H” level
(the power source voltage should be between VCC (min.) and 5.5 V,
and the quartz-crystal oscillator should be stable), reset is released.
After the reset is completed, the program starts from the address
contained in address FFFD16 (high-order byte) and address FFFC16
(low-order byte). Make sure that the reset input voltage is less than
0.2Vcc when a power source voltage passes VCC (min.).
Poweron
RESET
VCC
(Note)
Power source
voltage
0V
Reset input
voltage
0V
0.2VCC
Note : Reset release voltage ; VCC=3.0 V.
RESET
VCC
Power source
voltage detection
circuit
Fig. 33 Reset circuit example
XIN
φ
RESET
Internal
reset
Reset address from
vector table
Address
?
?
?
Data
?
FFFC
ADL
FFFD
ADH, ADL
ADH
SYNC
XIN : about 8200 cycles
Notes 1: The frequency relation of f(XIN) and f(φ) is f(XIN) = 8 • f(φ).
2: The question marks (?) indicate an undefined state that
depends on the previous state.
Fig. 34 Reset sequence
35
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Address
Register contents
Address
000116
0016
(21) A-D control register
003116
0816
(2) Port P1 direction register
000316
0016
003216
XX16
(3) Port P2 direction register
000516
0016
003316
XX16
(4) Port P3 direction register
000716
0016
(22) A-D conversion register
(low-order)
(23) A-D conversion register
(high-order)
(24) LCD control register 1
003716
0016
(5) Port P4 direction register
000916
0016
(25) LCD control register 2
003816
0016
(6) PULL register A
001616
0016
(26) LCD mode register
003916
0316
(7) PULL register B
001716
0016
(27) Interrupt edge selection register 003A16
0016
(8) Serial I/O status register
001916
8016
(28) CPU mode register
003B16
4C16
(9) Serial I/O control register
001A16
0016
(29) Interrupt request register 1
003C16
0016
(10) UART control register
001B16
E016
(30) Interrupt request register 2
003D16
0016
(11) Timer X (low-order)
002016
FF16
(31) Interrupt control register 1
003E16
0016
(12) Timer X (high-order)
002116
FF16
(32) Interrupt control register 2
003F16
0016
(13) Timer Y (low-order)
002216
FF16
(33) Processor status register
(14) Timer Y (high-order)
002316
FF16
(34) Program counter
(15) Timer 1
002416
FF16
(16) Timer 2
002516
0116
(17) Timer 3
002616
FF16
(18) Timer X mode register
002716
0016
(19) Timer Y mode register
002816
0016
(20) Timer 123 mode register
002916
0016
(PS) ✕ ✕ ✕ ✕ ✕ 1 ✕ ✕
(PCH)
Contents of address FFFD16
(PCL)
Contents of address FFFC16
Note: The contents of all other register and RAM are undefined after reset, so they must be initialized by software.
✕ : Undefined
Fig. 35 Internal status at reset
36
Register contents
(1) Port P0 direction register
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
CLOCK GENERATING CIRCUIT
The 38C8 group has two built-in oscillation circuits. An oscillation
circuit can be formed by connecting a resonator between XIN and
XOUT (XCIN and XCOUT). RC oscillation is available for XIN-XOUT.
Immediately after power on, only the XIN oscillation circuit starts oscillating, and XCIN and XCOUT pins go to high impedance state.
Main Clock
An oscillation circuit by a resonator can be formed by setting the
OSCSEL pin is set to “L” level and connecting a resonator between
XIN and XOUT. Use the circuit constants in accordance with the resonator manufacturer’s recommended values. No external resistor is
needed between XIN and XOUT since a feed-back resistor exists onchip. To supply a clock signal externally, make the XOUT pin open in
the “L” level state of the OSCSEL pin, and supply the clock from the
XIN pin. The RC oscillation circuit can be formed by setting the
OSCSEL pin to “H” level and connecting a resistor between the XIN
pin and the X OUT pin. At this time, the feed-back resistor is cut off.
The frequency of the RC oscillation changes owing to a parasitic
capacitance or the wiring length etc. of the printed circuit board. Do
not use the RC oscillation in the usage which the frequency accuracy
of the main clock is needed.
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Oscillation Control
(1) Stop Mode
If the STP instruction is executed, the internal clock φ stops at an “H”
level, and XIN and XCIN oscillators stop. Timer 1 is set to “FF16 ” and
timer 2 is set to “0116.”
Either XIN divided by 16 or XCIN divided by 16 is input to timer 1 as
count source, and the output of timer 1 is connected to timer 2. The
bits except bit 4 of the timer 123 mode register are cleared to “0.” Set
the interrupt enable bits of timer 1 and timer 2 to disabled (“0”) before
executing the STP instruction.
Oscillator restarts when an external interrupt is received, but the internal clock φ is not supplied to the CPU until timer 2 underflows.
This allows time for the clock circuit oscillation to stabilize.
(2) Wait Mode
If the WIT instruction is executed, the internal clock φ stops at an “H”
level. The states of X IN and XCIN are the same as the state before
executing the WIT instruction. The internal clock φ restarts at reset
or when an interrupt is received. Since the oscillator does not stop,
normal operation can be started immediately after the clock is restarted.
Sub-clock
Connect a resonator between XCIN and XCOUT. An external feedback resistor is needed between XCIN and XCOUT since a feed-back
resistor does not exist on-chip. The sub-clock XCIN-XCOUT oscillation
circuit cannot directly input clocks that are externally generated. Accordingly, be sure to cause an external resonator to oscillate.
Frequency Control
(1) Middle-speed Mode
The internal clock φ is the frequency of XIN divided by 8. At reset, this
mode is selected.
XCIN
XCOUT OSCSEL
Rf
Rd
XIN
XOUT
Rosc
CCIN
(2) High-speed Mode
The internal clock φ is the frequency of X IN divided by 2.
(3) Low-speed Mode
Fig. 36 RC oscillation circuit
The internal clock φ is the frequency of XCIN divided by 2.
A low-power consumption operation can be realized by stopping the
main clock XIN in this mode. To stop the main clock, set bit 5 of the
CPU mode register to “1”. When the main clock XIN is restarted, set
enough time for oscillation to stabilize by programming.
■Notes on clock generating circuit
If you switch the mode between middle/high-speed and low-speed,
stabilize both XIN and XCIN oscillations. The sufficient time is required
for the sub clock to stabilize, especially immediately after power on
and at returning from stop mode. When switching the mode between
middle/high-speed and low-speed, set the frequency on condition
that f(XIN) > 3•f(X CIN).
XCIN XCOUT OSCSEL XIN XOUT
Rf
CCIN
Rd
CCOUT
CI N
COUT
Fig. 37 Resonator circuit
37
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
XCOUT
XCIN
XIN
XOUT
Timer 1 count
source selection
bit
Internal system clock selection bit
(Note)
Low-speed mode
“1”
1/2
“0”
Middle-/High-speed mode
Timer 2 count
source selection
bit
“1”
1/2
1/4
Timer 1
“0”
“0”
Timer 2
“1”
Main clock division ratio selection bit
Middle-speed mode
“1”
Main clock stop bit
Q
S
S
R
STP instruction
WIT
instruction
Q
R
Reset
Interrupt disable flag
I
Interrupt request
Note: When selecting the XC oscillation, set the port XC switch bit to “1” .
Fig. 38 Clock generating circuit block diagram
38
Timing φ
(Internal clock)
“0”
High-speed mode
or Low-speed mode
Q
S
R
STP instruction
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Reset
“0”
“0
”
“0
”
C
“1 M4
C ”
M
CM7 = 0 (4 MHz selected)
CM6 = 0 (High-speed)
CM5 = 0 (4 MHz oscillating)
CM4 = 0 (32 kHz stoped)
4
”
“0
“1
”
6
”
“1
CM6
Middle-speed mode (f(φ) = 0.5 MHz)
High-speed mode (f(φ) = 2 MHz)
“0”
CM7 = 0 (4 MHz selected)
CM6 = 0 (High-speed)
CM5 = 0 (4 MHz oscillating)
CM4 = 1 (32 kHz oscillating)
CM6
“1”
“0”
CM7 = 1 (32 kHz selected)
CM6 = 0 (High-speed)
CM5 = 0 (4 MHz oscillating)
CM4 = 1 (32 kHz oscillating)
CM7
“1”
CM7
“1”
“0”
“1”
“0”
CM7 = 0 (4 MHz selected)
CM6 = 1 (Middle-speed)
CM5 = 0 (4 MHz oscillating)
CM4 = 1 (32 kHz oscillating)
“0
”
”
“1
”
“0
C
“1 M5
C ”
“1 M6
”
“0
”
5
“0”
M
C ”
“0 M6
C ”
“1
CM5
“1”
Low-speed mode (f(φ) =16 kHz)
“0”
Low-speed mode (f(φ) = 16 kHz)
CM7 = 1 (32 kHz selected)
CM6 = 1 (Middle-speed)
CM5 = 0 (4 MHz oscillating)
CM4 = 1 (32 kHz oscillating)
Low-speed mode (f(φ) =16 kHz)
CM6
CM7 = 1 (32 kHz selected)
CM6 = 1 (Middle-speed)
CM5 = 1 (4 MHz stopped)
CM4 = 1 (32 kHz oscillating)
“1”
CM5
“1”
CM4
“1”
High-sp eed mode (f(φ) = 2 MHz)
“0”
M
C
”
“0 M6
C
”
“1
“0”
CM7 = 0 (4 MHz selected)
CM6 = 1 (Middle-speed)
CM5 = 0 (4 MHz oscillating)
CM4 = 0 (32 kHz stoped)
CM4
“1”
CM6
“1”
Middle-speed mode (f(φ) = 0 .5 MHz)
Low-speed mode (f(φ) =1 6 kHz)
“0”
CM7 = 1 (32 kHz selected)
CM6 = 0 (High-speed)
CM5 = 1 (4 MHz stopped)
CM4 = 1 (32 kHz oscillating)
b7
b4
CPU mode register
(CPUM : address 003B16)
CM4 : Sub-clock stop bit
0: Stopped
1: Oscillating
CM5 : Main clock (XIN–XOUT) stop bit
0: Oscillating
1: Stopped
CM6 : Main clock division ratio selection bit
0: f(XIN)/2 (high-speed mode)
1: f(XIN)/8 (middle-speed mode)
CM7 : Internal system clock selection bit
0: XIN–XOUT selected
(middle-/high-speed mode)
1: XCIN–XCOUT selected
(low-speed mode)
Notes 1 : Switch the mode by the allows shown between the mode blocks. (Do not switch between the mode directly without an allow.)
2 : T he all modes can be switched to the stop mode or the wait mode and returned to the source mode when the stop mode or the wait mode is ended.
3 : T imer and LCD operate in the wait mode.
4 : When the stop mode is ended, a delay of approximately 1 ms occurs automatically by timer 1 and timer 2 in middle-/high-speed mode.
5 : When the stop mode is ended, a delay of approximately 0.25 s occurs automatically by timer 1 and timer 2 in low-speed mode.
6 : Wait until oscillation stabilizes after oscillating the main clock XIN before the switching from the low-speed mode to middle-/high-speed mode.
7 : T he example assumes that 4 MHz is being applied to the XIN pin and 32 kHz to the XCIN pin. φ indicates the internal clock.
Fig. 39 State transitions of system clock
39
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
NOTES ON PROGRAMMING
Processor Status Register
The contents of the processor status register (PS) after a reset are
undefined, except for the interrupt disable flag (I) which is “1.” After a
reset, initialize flags which affect program execution. In particular, it
is essential to initialize the index X mode (T) and the decimal mode
(D) flags because of their effect on calculations.
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
A-D Converter
The comparator is constructed linked to a capacitor. When the conversion speed is not enough, the conversion accuracy might be ruined by the disappearance of the charge. When A-D conversion is
performed in the middle-speed mode or the high-speed mode, set
f(XIN) to at least 500 kHz.
Do not execute the STP or WIT instruction during an A-D conversion
because a normal conversion result is not obtained.
Interrupts
The contents of the interrupt request bits do not change immediately
after they have been written. After writing to an interrupt request register, execute at least one instruction before performing a BBC or
BBS instruction.
Decimal Calculations
• To calculate in decimal notation, set the decimal mode flag (D) to
“1,” then execute an ADC or SBC instruction. After executing an
ADC or SBC instruction, execute at least one instruction before
executing a SEC, CLC, or CLD instruction.
• In decimal mode, the values of the negative (N), overflow (V), and
zero (Z) flags are invalid.
Instruction Execution Time
The instruction execution time is obtained by multiplying the frequency
of the internal clock φ by the number of cycles needed to execute an
instruction.
The number of cycles required to execute an instruction is shown in
the list of machine instructions.
The frequency of the internal clock φ is half of the XIN frequency.
At STP Instruction Release
At the STP instruction release, all bits of the timer 12 mode register
are cleared.
LCD Control
Timers
If a value n (between 0 and 255) is written to a timer latch, the frequency division ratio is 1/(n+1).
Multiplication and Division Instructions
• The index X mode (T) and the decimal mode (D) flags do not affect
the MUL and DIV instruction.
• The execution of these instructions does not change the contents
of the processor status register.
Ports
The contents of the port direction registers cannot be read. The following cannot be used:
• The data transfer instruction (LDA, etc.)
• The operation instruction when the index X mode flag (T) is “1”
• The addressing mode which uses the value of a direction register
as an index
• The bit-test instruction (BBC or BBS, etc.) to a direction register
• The read-modify-write instructions (ROR, CLB, or SEB, etc.) to a
direction register.
Use instructions such as LDM and STA, etc., to set the port direction
registers.
Serial I/O
In clock synchronous serial I/O, if the receive side is using an external clock and it is to output the SRDY signal, set the transmit enable
bit, the receive enable bit, and the SRDY output enable bit to “1”.
Serial I/O continues to output the final bit from the TxD pin after transmission is completed.
40
When using the voltage multiplier, apply prescribed voltage to the
VLIN pin in the state in which the LCD enable bit is “0”, and set the
voltage multiplier enable bit to “1”.
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
MITSUBISHI MICROCOMPUTERS
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
DATA REQUIRED FOR MASK ORDERS
ROM PROGRAMMING METHOD
The following are necessary when ordering a mask ROM production:
1. Mask ROM Order Confirmation Form✽1
2. Mark Specification Form ✽2
3. Data to be written to ROM, in EPROM form (three identical copies)
or one floppy disk.
The built-in PROM of the blank One Time PROM version and built-in
EPROM version can be read or programmed with a general-purpose
PROM programmer using a special programming adapter
(PCA7447FP).
The PROM of the blank One Time PROM version is not tested or
screened in the assembly process and following processes. To ensure proper operation after programming, the procedure shown in
Figure 40 is recommended to verify programming.
For the mask ROM confirmation and the mark specifications, refer to
the “Mitsubishi MCU Technical Information” Homepage.
✽1 Mask ROM Confirmation Forms
http://www.infomicom.mesc.co.jp/38000/38ordere.htm
✽2 Mark Specification Forms
http://www.infomicom.mesc.co.jp/mela/markform.htm
Programming with PROM
programmer
Screening (Caution)
(150°C for 40 hours)
Verification with
PROM programmer
Functional check in
target device
Caution : The screening temperature is far higher
than the storage temperature. Never
expose to 150 °C exceeding 100 hours.
Fig. 40 Programming and testing of One Time PROM version
41
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
ELECTRICAL CHARACTERISTICS
Table 10 Absolute maximum ratings
Parameter
Symbol
Power source voltage
VCC
Input voltage
P00–P07 , P10–P1 7, P20–P2 7,
VI
P30–P33, P40–P4 7
Input voltage
C1, C2
VI
Input voltage
RESET, XIN, XCIN
VI
Input voltage
VLIN
VI
VI
VO
VO
VO
VO
Pd
Topr
Tstg
Input voltage
Output voltage
VL1, VL2, VL3, VL4 , VL5
P00–P07 , P10–P1 7, P20–P2 7,
P30–P33, P41–P4 7
Output voltage C1, C2, C 3
Output voltage COM 0–COM31, SEG0–SEG67
Output voltage XOUT, XCOUT
Power dissipation
Operating temperature
Storage temperature
Conditions
All voltages are based on
Vss. Output transistors
are cut off.
When voltage multiplier is
not operated.
VL1≤VL2≤VL3 ≤VL4≤VL5
Ta = 25°C
Ratings
–0.3 to 7.0
–0.3 to VCC+0.3
Unit
V
V
–0.3 to 7.0
–0.3 to VCC+0.3
–0.3 to 7.0
V
V
V
–0.3 to 7.0
–0.3 to VCC+0.3
V
V
–0.3 to 7.0
–0.3 to VL5+0.3
–0.3 to VCC+0.3
300
–20 to 85
–40 to 125
V
V
V
mW
°C
°C
Table 11 Recommended operating conditions (Vcc = 2.2 to 5.5 V, Ta = –20 to 85°C, unless otherwise noted)
Limits
Symbol
Parameter
Min.
Typ.
VCC
Power source
High-speed mode f(XIN) ≤ 8 MHz
4.0
5.0
voltage
High-speed mode f(XIN) ≤ 4 MHz
3.0
5.0
Middle-speed mode f(X IN) ≤ 8 MHz
2.7
5.0
Middle-speed mode (mask ROM version) f(X IN) ≤ 4 MHz
2.2
5.0
Middle-speed mode (One Time PROM version) f(X IN) ≤ 4 MHz
2.5
5.0
Low-speed mode (mask ROM version)
2.2
5.0
Low-speed mode (One Time PROM version)
2.5
5.0
VSS
Power source voltage
0
VLIN
Power source voltage
VLIN
VL5
Power source voltage
VL5
VIA
Analog input voltage
AN0 –AN7
VSS
VIH
“H” input voltage
P00–P07 , P10–P1 7, P40, P4 3, P4 5, P47
0.7VCC
VIH
“H” input voltage
P20–P27 , P30–P3 3, P41, P4 2, P4 4, P46
0.8VCC
VIH
“H” input voltage
RESET
0.8VCC
VIH
“H” input voltage
XIN
0.8VCC
VIL
“L” input voltage
P00–P07 , P10–P1 7, P40, P4 3, P4 5, P47
VSS
VIL
“L” input voltage
P20–P27 , P30–P3 3, P41, P4 2, P4 4, P46
VSS
VIL
“L” input voltage
RESET
VSS
VIL
“L” input voltage
XIN
VSS
ΣIOH(peak) “H” total peak output current
All ports
(Note 1)
ΣIOL(peak) “L” total peak output current
All ports
(Note 1)
ΣIOH(avg) “H” total average output current All ports
(Note 2)
ΣIOL(avg)
“L” total average output current All ports
(Note 2)
I OH(peak)
“H” peak output current
All ports
(Note 3)
I OL(peak)
“L” peak output current
All ports
(Note 3)
I OH(avg)
“H” average output current
All ports
(Note 4)
I OL(avg)
“L” average output current
All ports
(Note 4)
ROSC
Oscillation resistor at selecting RC oscillation
5
8.2
Notes 1: The total peak output current is the peak value of the peak currents flowing through all the applicable ports.
2: The total average output current is the average value measured over 100 ms flowing through all the applicable ports.
3: The peak output current is the peak current flowing in each port.
4: The average output current is an average value measured over 100 ms.
42
Max.
5.5
5.5
5.5
5.5
5.5
5.5
5.5
2.33
7.0
VCC
VCC
VCC
VCC
VCC
0.3VCC
0.2VCC
0.2VCC
0.2VCC
–60.0
60.0
–30.0
30.0
–5.0
10.0
–2.5
5.0
10
Unit
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
mA
mA
mA
mA
mA
mA
mA
mA
kΩ
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 12 Recommended operating conditions (mask ROM version) (Vcc = 2.2 to 5.5 V, Ta = –20 to 85°C, unless otherwise noted)
Symbol
f(CNTR 0)
f(CNTR 1)
f(X IN)
f(X CIN)
Parameter
Conditions
Min.
Limits
Typ.
Timer X, timer Y input frequency (duty cycle 50%)
Main clock input oscillation frequency (Note 1)
High-speed mode
(4.0 V ≤ VCC ≤ 5.5 V)
High-speed mode
(2.2 V ≤ VCC < 4.0 V)
Middle-speed mode
(2.7 V ≤ VCC ≤ 5.5 V)
Sub-clock input oscillation frequency (Notes 1, 2)
32.768
Unit
Max.
f(XIN)/2
MHz
8.0
MHz
(20✕V CC–8)/13
MHz
8.0
MHz
50
kHz
Notes 1: When the oscillation frequency has a duty cycle of 50 %.
2: When using the microcomputer in low-speed mode, set the sub-clock input oscillation frequency on condition that f(XCIN ) < f(XIN)/3.
Table 13 Recommended operating conditions (PROM version) (Vcc = 2.5 to 5.5 V, Ta = –20 to 85°C, unless otherwise noted)
Symbol
f(CNTR0)
f(CNTR1)
f(XIN)
f(XCIN)
Parameter
Conditions
Min.
Limits
Typ.
Timer X, timer Y input frequency (duty cycle 50%)
Main clock input oscillation frequency (Note 1)
Sub-clock input oscillation frequency (Notes 1, 2)
High-speed mode
(4.0 V ≤ VCC ≤ 5.5 V)
High-speed mode
(2.5 V ≤ VCC < 4.0 V)
Middle-speed mode
(2.7 V ≤ VCC ≤ 5.5 V)
32.768
Unit
Max.
f(XIN)/2
MHz
8.0
MHz
4✕V CC–8
MHz
8.0
MHz
50
kHz
Notes 1: When the oscillation frequency has a duty cycle of 50 %.
2: When using the microcomputer in low-speed mode, set the sub-clock input oscillation frequency on condition that f(X CIN) < f(XIN )/3.
43
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 14 Electrical characteristics (Vcc = 2.2 to 5.5 V, Ta = –20 to 85°C, unless otherwise noted)
Symbol
VOH
VOH
VOL
VOL
VT+–VTVT+–VTVT+–VTI IH
I IH
I IH
I IL
I IL
I IL
44
Parameter
“H” output voltage
P00–P07, P1 0–P1 7, P30–P3 3
“H” output voltage
P20–P27, P4 1–P4 7
“L” output voltage
P00–P07, P1 0–P1 7, P30–P3 3
“L” output voltage
P20–P27, P4 1–P4 7
Hysteresis
INT0, INT1, ADT, CNTR0 , CNTR1, P20 –P27
Hysteresis SCLK, RxD
Hysteresis RESET
“H” input current All ports
“H” input current RESET
“H” input current XIN
“L” input current All ports
“L” input current
“L” input current
RESET
XIN
Test conditions
I OH = –5.0 mA
VCC = 5.0 V
I OH = –1.5 mA
VCC = 5.0 V
I OH = –1.25 mA
VCC = 2.2 V
I OH = –5.0 mA
VCC = 5.0 V
I OH = –1.5 mA
VCC = 5.0 V
I OH = –1.25 mA
VCC = 2.2 V
I OL = 5.0 mA
VCC = 5.0 V
I OL = 1.5 mA
VCC = 5.0 V
I OL = 1.25 mA
VCC = 2.2 V
I OL = 5.0 mA
VCC = 5.0 V
I OL = 1.5 mA
VCC = 5.0 V
I OL = 1.25 mA
VCC = 2.2 V
Min.
VCC–2.0
Limits
Typ.
Max.
V
VCC–0.5
V
VCC–1.0
V
VCC–2.0
V
VCC–0.5
V
VCC–1.0
V
2.0
V
0.5
V
1.0
V
2.0
V
0.5
V
1.0
V
0.5
V
0.5
0.5
–5.0
V
V
µA
µA
µA
µA
5.0
5.0
4.0
VI = VSS
Pull-ups “off”
VCC = 5.0 V, VI = VCC
Pull-ups “on”
VCC = 2.2 V, VI = VCC
Pull-ups “on”
VI = VSS
VI = VSS
Unit
–60.0
–120.0
–240.0
µA
–5.0
–20.0
–40.0
µA
–5.0
µA
µA
–4.0
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 15 Electrical characteristics (Vcc = 2.2 to 5.5 V, Ta = –20 to 85°C, unless otherwise noted)
Symbol
VRAM
I CC
I AD
I L5
FROSC
Parameter
RAM hold voltage
Power source current
A-D converter current
dissipation
VL5 input current (Note)
RC oscillation frequency
Test conditions
When clock is stopped
High-speed mode, Vcc = 5.0 V
f(XIN) = 8.0 MHz
f(XCIN) = 32.768 kHz
Middle-speed mode, Vcc = 5.0 V
f(XIN) = 8.0 MHz
f(XCIN) = 32.768 kHz
Middle-speed mode, Vcc = 3.0 V
f(XIN) = 8.0 MHz
f(XCIN) = 32.768 kHz
Low-speed mode, VCC = 3.0 V,
f(XIN) = stopped
f(XCIN) = 32.768 kHz
High-/Middle-speed mode, VCC =
5.0 V,
f(XIN) = 8.0 MHz (in WIT state)
f(XCIN) = 32.768 kHz
Middle-speed mode, Vcc = 3.0 V
f(XIN) = 8.0 MHz (in WIT state)
f(XCIN) = 32.768 kHz
Low-speed mode, VCC = 3.0 V,
f(XIN) = stopped
f(XCIN) = 32.768 kHz (in WIT state)
All oscillation stopped
Ta = 25 °C, Output transistors “off”
(in STP state)
All oscillation stopped
Ta = 85 °C, Output transistors “off”
(in STP state)
Current increase at A-D converter
operated, f(XIN) = 8.0 MHz
VL5 = 6.0 V, Ta = 25 °C
ROSC = 8.2 kΩ
Min.
2.0
1.5
Limits
Typ.
5.0
5.5
Max.
5.5
11.0
3.0
6.0
mA
1.0
2.0
mA
20.0
40.0
µA
0.9
1.8
mA
0.3
0.6
mA
4.5
9.0
µA
0.1
1.0
µA
10.0
µA
0.8
1.6
mA
3
2.5
6
3.5
µA
MHz
Unit
V
mA
Note: When normal drivability (drivability selection bit 1 = “0”, drivability selection bit 2 = “0”) is selected.
45
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 16 A-D converter characteristics
(Vcc = 2.2 to 5.5 V, Vss = 0 V, Ta = –20 to 85°C, f(XIN) ≤ 4 MHz, in middle-speed/high-speed mode)
Symbol
—
—
t conv
I IA
Parameter
Test conditions
Resolution
Absolute accuracy
(excluding quantization error)
Conversion time
Analog port input current
Limits
Typ.
Min.
VCC = 2.7–5.5 V
VCC = 2.5–2.7 V (Ta = –10 to 50 °C)
f(X IN) = 4 MHz (Note)
30.5
0.5
Max.
10
±4
±6
34
5.0
Unit
Bits
LSB
LSB
µs
µA
Note: When main clock is selected as system clock.
Table 17 Timing requirements 1 (Vcc = 4.0 to 5.5 V, Vss = 0 V, Ta = –20 to 85°C, unless otherwise noted)
Symbol
t w(RESET)
t c(XIN)
t wH(XIN)
t wL(XIN)
t c(CNTR)
t wH(CNTR)
t wL(CNTR)
t wH(INT)
t wL(INT)
t c(SCLK)
t wH(SCLK)
t wL(SCLK)
t su(RxD-S CLK)
t h(SCLK-RxD)
Parameter
Reset input “L” pulse width
Main clock input cycle time (XIN input)
Main clock input “H” pulse width
Main clock input “L” pulse width
CNTR0 , CNTR1 input cycle time
CNTR0 , CNTR1 input “H” pulse width
CNTR0 , CNTR1 input “L” pulse width
INT0, INT1 input “H” pulse width
INT0, INT1 input “L” pulse width
Serial I/O clock input cycle time
Serial I/O clock input “H” pulse width
Serial I/O clock input “L” pulse width
Serial I/O input setup time
Serial I/O input hold time
(Note)
(Note)
(Note)
Limits
Typ.
Min.
2
125
45
40
250
105
105
80
80
800
370
370
220
100
Max.
Unit
µs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Note: When bit 6 of address 001A16 is “1”.
Divide this value by four when bit 6 of address 001A16 is “0”.
Table 18 Timing requirements 2 (Vcc = 2.2 to 4.0 V, Vss = 0 V, Ta = –20 to 85°C, unless otherwise noted)
Symbol
t w(RESET)
t c(XIN)
t wH(XIN)
t wL(XIN)
t c(CNTR)
t wH(CNTR)
t wL(CNTR)
t wH(INT)
t wL(INT)
t c(SCLK)
t wH(SCLK)
t wL(SCLK)
t su(RxD-S CLK)
t h(SCLK-RxD)
Reset input “L” pulse width
Main clock input cycle time (XIN input)
Main clock input “H” pulse width
Main clock input “L” pulse width
CNTR0 , CNTR1 input cycle time
CNTR0 , CNTR1 input “H” pulse width
CNTR0 , CNTR1 input “L” pulse width
NT0, INT1 input “H” pulse width
NT0, INT1 input “L” pulse width
Serial I/O clock input cycle time
Serial I/O clock input “H” pulse width
Serial I/O clock input “L” pulse width
Serial I/O input setup time
Serial I/O input hold time
Note: When bit 6 of address 001A16 is “1”.
Divide this value by four when bit 6 of address 001A16 is “0”.
46
Limits
Parameter
(Note)
(Note)
(Note)
Min.
2
125
45
40
900/(VCC–0.4)
tc(CNTR)/2–20
tc(CNTR)/2–20
230
230
2000
950
950
400
200
Typ.
Max.
Unit
µs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 19 Switching characteristics 1 (Vcc = 4.0 to 5.5 V, Vss = 0 V, Ta = –20 to 85°C, unless otherwise noted)
Symbol
t wH(SCLK)
t wL(SCLK)
t d(SCLK-TxD)
t V(SCLK-TxD)
t r(SCLK)
t f(SCLK)
t r(CMOS)
t f(CMOS)
Limits
Parameter
Serial I/O clock output “H” pulse width
Serial I/O clock output “L” pulse width
Serial I/O output delay time
Serial I/O output valid time
Serial I/O clock output rising time
Serial I/O clock output falling time
CMOS output rising time
CMOS output falling time
Min.
t c(SCLK)/2–30
t c(SCLK)/2–30
(Note 1)
(Note 1)
Typ.
Max.
140
–30
(Note 2)
(Note 2)
30
30
30
30
10
10
Unit
ns
ns
ns
ns
ns
ns
ns
ns
Notes 1: When the P45 /TxD P-channel output disable bit of the UART control register (bit 4 of address 001B 16) is “0”.
2: The X OUT and X COUT pins are excluded.
Table 20 Switching characteristics 2 (Vcc = 2.2 to 4.0 V, Vss = 0 V, Ta = –20 to 85°C, unless otherwise noted)
Symbol
t wH(SCLK)
t wL(SCLK)
t d(SCLK-TxD)
t V(SCLK-TxD)
t r(SCLK)
t f(SCLK)
t r(CMOS)
t f(CMOS)
Limits
Parameter
Serial I/O clock output “H” pulse width
Serial I/O clock output “L” pulse width
Serial I/O output delay time
Serial I/O output valid time
Serial I/O clock output rising time
Serial I/O clock output falling time
CMOS output rising time
CMOS output falling time
Min.
t C(SCLK)/2–50
t C(SCLK)/2–50
(Note 1)
(Note 1)
Typ.
Max.
350
–30
(Note 2)
(Note 2)
50
50
50
50
20
20
Unit
ns
ns
ns
ns
ns
ns
ns
ns
Notes 1: When the P45 /TxD P-channel output disable bit of the UART control register (bit 4 of address 001B 16) is “0”.
2: The X OUT and X COUT pins are excluded.
1 kΩ
Measurement output pin
100 pF
Measurement output pin
100 pF
CMOS output
N-channel open-drain output (Note)
Note: When bit 4 of the UART control register
(address 001B16) is “1”. (N-channel opendrain output mode)
Fig. 41 Circuit for measuring output switching characteristics
47
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
tC(CNTR)
tWL(CNTR)
tWH(CNTR)
C N T R 0, C N T R 1
0.8VCC
0.2VCC
tWL(INT)
tWH(INT)
INT0, INT1
0.8VCC
0.2VCC
tW(RESET)
RESET
0.8VCC
0.2VCC
tC(XIN)
tWL(XIN)
tWH(XIN)
0.8VCC
XIN
0.2VCC
tC(SCLK)
tf
SCLK
tWL(SCLK)
td(SCLK-TXD)
48
th(SCLK-RXD)
0.8VCC
0.2VCC
RXD
Fig. 42 Timing diagram
tWH(SCLK)
0.8VCC
0.2VCC
tsu(RXD-SCLK)
TXD
tr
tv(SCLK-TXD)
MITSUBISHI MICROCOMPUTERS
RY
A
N
I
.
ion
cat o
cifi
t
spe bject
l
a
u
n
a fi are s
not
its
is is ric lim
h
T
t
e
ice:
am
Not e par
Somnge.
cha
L
PRE
IM
38C8 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
PACKAGE OUTLINE
MMP
EIAJ Package Code
LQFP144-P-2020-0.50
Plastic 144pin 20✕20mm body LQFP
Weight(g)
1.23
JEDEC Code
–
Lead Material
Cu Alloy
MD
e
144P6Q-A
b2
D
144
ME
HD
109
1
l2
Recommended Mount Pad
108
36
A
A1
A2
b
c
D
E
e
HD
HE
L
L1
Lp
HE
E
Symbol
73
37
72
A
L1
F
e
x
M
L
Detail F
Lp
c
b
A1
y
A3
A2
A3
x
y
b2
I2
MD
ME
Dimension in Millimeters
Min
Nom
Max
–
–
1.7
0.125
0.2
0.05
–
–
1.4
0.17
0.22
0.27
0.105
0.125
0.175
19.9
20.0
20.1
19.9
20.0
20.1
–
0.5
–
21.8
22.0
22.2
21.8
22.0
22.2
0.35
0.5
0.65
1.0
–
–
0.45
0.6
0.75
–
0.25
–
–
–
0.08
–
–
0.1
–
0°
8°
–
–
0.225
0.95
–
–
20.4
–
–
–
–
20.4
49
HEAD OFFICE: 2-2-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
Keep safety first in your circuit designs!
•
Mitsubishi Electric Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to
personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of non-flammable
material or (iii) prevention against any malfunction or mishap.
•
These materials are intended as a reference to assist our customers in the selection of the Mitsubishi semiconductor product best suited to the customer’s application; they do not convey any license under any intellectual property
rights, or any other rights, belonging to Mitsubishi Electric Corporation or a third party.
Mitsubishi Electric Corporation assumes no responsibility for any damage, or infringement of any third-party’s rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples
contained in these materials.
All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by
Mitsubishi Electric Corporation without notice due to product improvements or other reasons. It is therefore recommended that customers contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product
distributor for the latest product information before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors. Mitsubishi Electric Corporation assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors.
Please also pay attention to information published by Mitsubishi Electric Corporation by various means, including the Mitsubishi Semiconductor home page (http://www.mitsubishichips.com).
When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision
on the applicability of the information and products. Mitsubishi Electric Corporation assumes no responsibility for any damage, liability or other loss resulting from the information contained herein.
Mitsubishi Electric Corporation semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Mitsubishi Electric
Corporation or an authorized Mitsubishi Semiconductor product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical,
aerospace, nuclear, or undersea repeater use.
The prior written approval of Mitsubishi Electric Corporation is necessary to reprint or reproduce in whole or in part these materials.
If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved
destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited.
Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for further details on these materials or the products contained therein.
Notes regarding these materials
•
•
•
•
•
•
•
© 2001 MITSUBISHI ELECTRIC CORP.
First publication, effective Jan. 2001.
Specifications subject to change without notice.
REVISION HISTORY
Rev.
38C8 GROUP DATA SHEET
Date
Description
Summary
Page
1.0
01/18/01
First Edition
(1/1)
Similar pages