Samsung M393T5750CZA-CD5 Ddr2 registered sdram module 240pin registered module based on 512mb c-die 72-bit ecc Datasheet

512MB, 1GB, 2GB Registered DIMMs
DDR2 SDRAM
DDR2 Registered SDRAM MODULE
240pin Registered Module based on 512Mb C-die
72-bit ECC
INFORMATION IN THIS DOCUMENT IS PROVIDED IN RELATION TO SAMSUNG PRODUCTS,
AND IS SUBJECT TO CHANGE WITHOUT NOTICE.
NOTHING IN THIS DOCUMENT SHALL BE CONSTRUED AS GRANTING ANY LICENSE,
EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE,
TO ANY INTELLECTUAL PROPERTY RIGHTS IN SAMSUNG PRODUCTS OR TECHNOLOGY. ALL
INFORMATION IN THIS DOCUMENT IS PROVIDED
ON AS "AS IS" BASIS WITHOUT GUARANTEE OR WARRANTY OF ANY KIND.
1. For updates or additional information about Samsung products, contact your nearest Samsung office.
2. Samsung products are not intended for use in life support, critical care, medical, safety equipment, or similar
applications where Product failure couldresult in loss of life or personal or physical harm, or any military or
defense application, or any governmental procurement to which special terms or provisions may apply.
* Samsung Electronics reserves the right to change products or specification without notice.
Rev. 1.2 Aug. 2005
512MB, 1GB, 2GB Registered DIMMs
DDR2 SDRAM
DDR2 Registered DIMM Ordering Information
Density
Organization
Component Composition
Number of Rank
Parity Register
M393T6553CZ3-CD5/CC
Part Number
512MB
64Mx72
64Mx8(K4T51083QC)*9EA
1
X
Height
30mm
M393T6553CZA-CE7/E6/D5/CC
512MB
64Mx72
64Mx8(K4T51083QC)*9EA
1
O
30mm
M393T2953CZ3-CD5/CC
1GB
128Mx72
64Mx8(K4T51083QC)*18EA
2
X
30mm
M393T2953CZA-CE7/E6/D5/CC
1GB
128Mx72
64Mx8(K4T51083QC)*18EA
2
O
30mm
M393T2950CZ3-CD5/CC
1GB
128Mx72
128Mx4(K4T51043QC)*18EA
1
X
30mm
M393T2950CZA-CE7/E6/D5/CC
1GB
128Mx72
128Mx4(K4T51043QC)*18EA
1
O
30mm
M393T5750CZ3-CD5/CC
2GB
256Mx72
128Mx4(K4T51043QC)*36EA
2
X
30mm
M393T5750CZA-CE7/E6/D5/CC
2GB
256Mx72
128Mx4(K4T51043QC)*36EA
2
O
30mm
Note: “Z” of Part number(11th digit) stand for Lead-free products.
Note: “3” of Part number(12th digit) stand for Dummy Pad PCB products.
Note: "A" of Part number(12th digit) stand for Parity Register products.
Features
• Performance range
E7(DDR2-800)
E6(DDR2-667)
D5(DDR2-533)
CC(DDR2-400)
Unit
Speed@CL3
400
400
400
400
Mbps
Speed@CL4
533
533
533
400
Mbps
Speed@CL5
800
667
-
-
Mbps
CL-tRCD-tRP
5-5-5
5-5-5
4-4-4
3-3-3
CK
• JEDEC standard 1.8V ± 0.1V Power Supply
• VDDQ = 1.8V ± 0.1V
• 200 MHz fCK for 400Mb/sec/pin, 267MHz fCK for 533Mb/sec/pin, 333MHz fCK for 667Mb/sec/pin, 400MHz fCK for 800Mb/sec/pin
• 4 Banks
• Posted CAS
• Programmable CAS Latency: 3, 4, 5
• Programmable Additive Latency: 0, 1 , 2 , 3 and 4
• Write Latency(WL) = Read Latency(RL) -1
• Burst Length: 4 , 8(Interleave/nibble sequential)
• Programmable Sequential / Interleave Burst Mode
• Bi-directional Differential Data-Strobe (Single-ended data-strobe is an optional feature)
• Off-Chip Driver(OCD) Impedance Adjustment
• On Die Termination with selectable values(50/75/150 ohms or disable)
• PASR(Partial Array Self Refresh)
• Average Refresh Period 7.8us at lower than a TCASE 85°C, 3.9us at 85°C < TCASE < 95 °C
- support High Temperature Self-Refresh rate enable feature
• Serial presence detect with EEPROM
• DDR2 SDRAM Package: 60ball FBGA - 128Mx4/64Mx8
• All of Lead-free products are compliant for RoHS
Note: For detailed DDR2 SDRAM operation, please refer to Samsung’s Device operation & Timing diagram.
Address Configuration
Organization
Row Address
Column Address
Bank Address
128Mx4(512Mb) based Module
A0-A13
A0-A9,A11
BA0-BA1
Auto Precharge
A10
64Mx8(512Mb) based Module
A0-A13
A0-A9
BA0-BA1
A10
Rev. 1.2 Aug. 2005
512MB, 1GB, 2GB Registered DIMMs
DDR2 SDRAM
Pin Configurations (Front side/Back side)
Pin
Front
Pin
Back
Pin
Front
Pin
Back
Pin
Front
Pin
Back
Pin
Front
Pin
Back
1
VREF
121
VSS
31
DQ19
151
VSS
61
A4
181
VDDQ
91
VSS
211
DM5/DQS14
NC/DQS14
2
VSS
122
DQ4
32
VSS
152
DQ28
62
VDDQ
182
A3
92
DQS5
212
3
DQ0
123
DQ5
33
DQ24
153
DQ29
63
A2
183
A1
93
DQS5
213
VSS
4
DQ1
124
VSS
34
DQ25
154
VSS
64
VDD
184
VDD
94
VSS
214
DQ46
DQ47
5
VSS
125
DM0/DQS9
35
VSS
155
DM3/DQS12
95
DQ42
215
6
DQS0
126
NC/DQS9
36
DQS3
156
NC/DQS12
65
VSS
185
CK0
96
DQ43
216
VSS
7
DQS0
127
VSS
37
DQS3
157
VSS
66
VSS
186
CK0
97
VSS
217
DQ52
DQ53
KEY
8
VSS
128
DQ6
38
VSS
158
DQ30
67
VDD
187
VDD
98
DQ48
218
9
DQ2
129
DQ7
39
DQ26
159
DQ31
68
NC/Par_In
188
A0
99
DQ49
219
VSS
10
DQ3
130
VSS
40
DQ27
160
VSS
69
VDD
189
VDD
100
VSS
220
RFU
RFU
11
VSS
131
DQ12
41
VSS
161
CB4
70
A10/AP
190
BA1
101
SA2
221
12
DQ8
132
DQ13
42
CB0
162
CB5
71
BA0
191
VDDQ
102
NC(TEST)
222
VSS
13
DQ9
133
VSS
43
CB1
163
VSS
72
VDDQ
192
RAS
103
VSS
223
DM6/DQS15
NC/DQS15
14
VSS
134
DM1/DQS10
44
VSS
164
DM8/DQS17
73
WE
193
S0
104
DQS6
224
15
DQS1
135
NC/DQS10
45
DQS8
165
NC/DQS17
74
CAS
194
VDDQ
105
DQS6
225
VSS
16
DQS1
136
VSS
46
DQS8
166
VSS
75
VDDQ
195
ODT0
106
VSS
226
DQ54
DQ55
17
VSS
137
RFU
47
VSS
167
CB6
76
S14
196
A13
107
DQ50
227
18
RESET
138
RFU
48
CB2
168
CB7
77
ODT1
197
VDD
108
DQ51
228
VSS
19
NC
139
VSS
49
CB3
169
VSS
78
VDDQ
198
VSS
109
VSS
229
DQ60
DQ61
20
VSS
140
DQ14
50
VSS
170
VDDQ
79
VSS
199
DQ36
110
DQ56
230
21
DQ10
141
DQ15
51
VDDQ
171
80
DQ32
200
DQ37
111
DQ57
231
VSS
22
DQ11
142
VSS
52
CKE0
172
CKE14
VDD
81
DQ33
201
VSS
112
VSS
232
DM7/DQS16
NC/DQS16
23
VSS
143
DQ20
53
VDD
173
NC
82
VSS
202
DM4/DQS13
113
DQS7
233
24
DQ16
144
DQ21
54
NC
174
83
DQS4
203
NC/DQS13
114
DQS7
234
VSS
25
DQ17
145
VSS
55
NC/Err_Out
175
NC
VDDQ
84
DQS4
204
VSS
115
VSS
235
DQ62
DQ63
26
VSS
146
DM2/DQS11
56
VDDQ
176
A12
85
VSS
205
DQ38
116
DQ58
236
27
DQS2
147
NC/DQS11
57
A11
177
A9
86
DQ34
206
DQ39
117
DQ59
237
VSS
28
DQS2
148
VSS
58
A7
178
VDD
87
DQ35
207
VSS
118
VSS
238
VDDSPD
29
VSS
149
DQ22
59
VDD
179
A8
88
VSS
208
DQ44
119
SDA
239
SA0
30
DQ18
150
DQ23
60
A5
180
A6
89
DQ40
209
120
SCL
240
SA1
90
DQ41
210
DQ45
VSS
NC = No Connect, RFU = Reserved for Future Use
1. RESET (Pin 18) is connected to both OE of PLL and Reset of register.
2. The Test pin (Pin 102) is reserved for bus analysis probes and is not connected on normal memory modules (DIMMs)
3. NC/Err_Out ( Pin 55) and NC/Par_In (Pin 68) are for optional function to check address and command parity.
4. CKE1,S1 Pin is used for double side Registered DIMM.
Pin Description
Pin Name
Description
Pin Name
Description
CK0
Clock Inputs, positive line
ODT0~ODT1
On die termination
CK0
Clock inputs, negative line
DQ0~DQ63
Data Input/Output
CKE0, CKE1
Clock Enables
CB0~CB7
Data check bits Input/Output
RAS
Row Address Strobe
DQS0~DQS8
Data strobes
CAS
Column Address Strobe
DQS0~DQS8
Data strobes, negative line
WE
Write Enable
DM(0~8),DQS(9~17)
Data Masks / Data strobes (Read)
S0, S1
Chip Selects
DQS9~DQS17
Data strobes (Read), negative line
A0~A9, A11~A13
Address Inputs
RFU
Reserved for Future Use
A10/AP
Address Input/Autoprecharge
NC
No Connect
BA0, BA1
DDR2 SDRAM Bank Address
TEST
Memory bus test tool
(Not Connect and Not Useable on DIMMs)
SCL
Serial Presence Detect (SPD) Clock Input
VDD
Core Power
SDA
SPD Data Input/Output
VDDQ
I/O Power
SA0~SA2
SPD address
VSS
Ground
Par_In
Parity bit for the Address and Control bus
VREF
Input/Output Reference
Err_Out
Parity error found in the Address and Control bus
VDDSPD
SPD Power
RESET
Register and PLL control pin
*The VDD and VDDQ pins are tied to the single power-plane on PCB.
Rev. 1.2 Aug. 2005
512MB, 1GB, 2GB Registered DIMMs
DDR2 SDRAM
Input/Output Functional Description
Symbol
Type
CK0
Input
CK0
Input
Negative line of the differential pair of system clock inputs that drives the input to the on-DIMM PLL.
Input
Activates the SDRAM CK signal when high and deactivates the CK signal when low. By deactivating the clocks, CKE low
initiates the Power Down mode, or the Self Refresh mode.
S0~S1
Input
Enables the associated SDRAM command decoder when low and disables decoder when high. When decoder is disabled,
new commands are ignored but previous operations continue.
These input signals also disable all outputs (except CKE and ODT) of the register(s) on the DIMM when both inputs are
high.
ODT0~ODT1
Input
I/O bus impedance control signals.
RAS, CAS, WE
Input
When sampled at the positive rising edge of the clock, CAS, RAS, and WE define the operation to be executed by the
SDRAM.
VREF
Supply
VDDQ
Supply
BA0~BA1
Input
Selects which SDRAM bank of four is activated.
Input
During a Bank Activate command cycle, Address defines the row address.
During a Read or Write command cycle, Address defines the column address. In addition to the column address, AP is
used to invoke autoprecharge operation at the end of the burst read or write cycle. If AP is high, autoprecharge is selected
and BA0, BA1 defines the bank to be precharged. If AP is low, autoprecharge is disabled. During a Precharge command
cycle, AP is used in conjunction with BA0, BA1 to control which bank(s) to precharge. If AP is high, all banks will be precharged regardless of the state of BA0 or BA1. If AP is low, BA0 and BA1 are used to define which bank to precharge.
DQ0~63,
CB0~CB7
In/Out
Data and Check Bit Input/Output pins
DM0~DM8
Input
Masks write data when high, issued concurrently with input data. Both DM and DQ have a write latency of one clock once
the write command is registered into the SDRAM.
CKE0~CKE1
A0~A9,A10/AP
A11~A13
Function
Positive line of the differential pair of system clock inputs that drives input to the on-DIMM PLL.
Reference voltage for SSTL_18 inputs
Isolated power supply for the DDR SDRAM output buffers to provide improved noise immunity
VDD, VSS
Supply
Power and ground for the DDR SDRAM input buffers and core logic
DQS0~DQS17
In/Out
Positive line of the differential data strobe for input and output data.
DQS0~DQS17
In/Out
Negative line of the differential data strobe for input and output data.
SA0~SA2
Input
These signals are tied at the system planar to either VSS or VDDSPD to configure the serial SPD EEPROM address range.
SDA
In/Out
This bidirectional pin is used to transfer data into or out of the SPD EEPROM. A resistor must be connected from the SDA
bus line to VDDSPD to act as a pullup.
SCL
Input
This signal is used to clock data into and out of the SPD EEPROM. A resistor may be connected from the SCL bus time
to VDDSPD to act as a pullup.
VDDSPD
Supply
Serial EEPROM positive power supply (wired to a separate power pin at the connector which supports from 1.7 Volt to 3.6
Volt operation).
RESET
Input
The RESET pin is connected to the RST pin on the register and to the OE pin on the PLL. When low, all register outputs
will be driven low and the PLL clocks to the DRAMs and register(s) will be set to low level (The PLL will remain synchronized with the input clock )
Par_In
Input
Parity bit for the Address and Control bus. ( “1 “ : Odd, “0 “ : Even)
Err_Out
Input
Parity error found in the Address and Control bus
TEST
In/Out
Used by memory bus analysis tools (unused on memory DIMMs)
Rev. 1.2 Aug. 2005
512MB, 1GB, 2GB Registered DIMMs
DDR2 SDRAM
Functional Block Diagram: 512MB, 64Mx72 Module(populated as 1 rank of x8 DDR2 SDRAMs)
M393T6553CZ3 / M393T6553CZA
RS0
DQS0
DQS0
DM0/DQS9
NC/DQS9
DQS4
DQS4
DM4/DQS13
NC/DQS13
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DM/ NU/ CS
RDQS RDQS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
DQS DQS
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
D0
DQS1
DQS1
DM1/DQS10
NC/DQS10
DM/ NU/ CS
RDQS RDQS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
DQS DQS
D4
DQS5
DQS5
DM5/DQS14
NC/DQS14
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
DM/ NU/ CS
RDQS RDQS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
DQS DQS
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
D1
DQS2
DQS2
DM2/DQS11
NC/DQS11
DM/ NU/ CS
RDQS RDQS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
DQS DQS
D5
DQS6
DQS6
DM6/DQS15
NC/DQS15
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
DM/ NU/ CS
RDQS RDQS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
DQS DQS
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
D2
DQS3
DQS3
DM3/DQS12
NC/DQS12
DM/ NU/ CS
RDQS RDQS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
DQS DQS
D6
DQS7
DQS7
DM7/DQS16
NC/DQS16
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
DM/ NU/ CS
RDQS RDQS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
DQS DQS
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
D3
DQS8
DQS8
DM8/DQS17
NC/DQS17
DM/ NU/ CS
RDQS RDQS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
DQS DQS
D7
Serial PD
SCL
CB0
CB1
CB2
CB3
CB4
CB5
CB6
CB7
DM/ NU/ CS
RDQS RDQS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
DQS DQS
D8
SDA
WP A0
A1
A2
SA0 SA1 SA2
VDDSPD
Serial PD
VDD/VDDQ
D0 - D8
VREF
D0 - D8
VSS
D0 - D8
Signals for Address and Command Parity Function (M393T6553CZA)
1:1
R
E
G
I
S
T
E
R
S0*
BA0-BA1
A0-A13
RAS
CAS
WE
CKE0
ODT0
RESET
RST
VSS
VSS
RSO-> CS : DDR2 SDRAMs D0-D8
RBA0-RBA1 -> BA0-BA1 : DDR2 SDRAMs D0-D8
RA0-RA13 -> A0-A13 : DDR2 SDRAMs D0-D8
RRAS -> RAS : DDR2 SDRAMs D0-D8
RCAS -> CAS : DDR2 SDRAMs D0-D8
RWE -> WE : DDR2 SDRAMs D0-D8
RCKE0 -> CKE : DDR2 SDRAMs D0-D8
RODT0 -> ODT0 : DDR2 SDRAMs D0-D8
PAR_IN
100K ohms
C0
C1
Register
PAR_IN
PPO
QERR
Err_Out
The resistors on Par_In, A13, A14, A15, BA2 and the
signal line of Err_Out refer to the section: "Register
Options for Unused Address inputs"
* S0 connects to DCS and VDD connects to CSR on the register.
PCK7
PCK7
Notes :
1. DQ-to-I/O wiring may be changed within a byte.
2. DQ/DQS/DM/CKE/S relationships must be maintained as shown.
3. Unless otherwise noted, resister values are 22 Ohms
CK0
CK0
RESET
P
L
L
OE
PCK0-PCK6, PCK8, PCK9 -> CK : DDR2 SDRAMs D0-D8
PCK0-PCK6, PCK8, PCK9 -> CK : DDR2 SDRAMs D0-D8
PCK7 -> CK : Register
PCK7 -> CK : Register
Rev. 1.2 Aug. 2005
512MB, 1GB, 2GB Registered DIMMs
DDR2 SDRAM
Functional Block Diagram: 1GB, 128Mx72 Module(populated as 2 rank of x8 DDR2 SDRAMs)
M393T2953CZ3 / M393T2953CZA
RS1
RS0
DQS0
DQS0
DM0/DQS9
NC/DQS9
DQS4
DQS4
DM4/DQS13
NC/DQS13
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DM/ NU/ CS
RDQS RDQS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
DQS DQS
DM/ NU/ CS
RDQS RDQS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
D0
DQS DQS
DM/ NU/ CS
RDQS RDQS
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
D9
DQS1
DQS1
DM1/DQS10
NC/DQS10
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
DQS DQS
DM/ NU/ CS
RDQS RDQS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
D4
DQS DQS
D13
DQS5
DQS5
DM5/DQS14
NC/DQS14
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
DM/ NU/ CS
RDQS RDQS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
DQS DQS
DM/ NU/ CS
RDQS RDQS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
D1
DQS DQS
D10
DQS2
DQS2
DM2/DQS11
NC/DQS11
DM/ NU/ CS
RDQS RDQS
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
DQS DQS
DM/ NU/ CS
RDQS RDQS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
D5
DQS DQS
D14
DQS6
DQS6
DM6/DQS15
NC/DQS15
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
DM/ NU/ CS
RDQS RDQS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
DQS DQS
DM/ NU/ CS
RDQS RDQS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
D2
DQS DQS
D11
DQS3
DQS3
DM3/DQS12
NC/DQS12
DM/ NU/ CS
RDQS RDQS
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
DQS DQS
DM/ NU/ CS
RDQS RDQS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
D6
DQS DQS
D15
DQS7
DQS7
DM7/DQS16
NC/DQS16
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
DM/ NU/ CS
RDQS RDQS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
DQS DQS
DM/ NU/ CS
RDQS RDQS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
D3
DQS DQS
D12
DQS8
DQS8
DM8/DQS17
NC/DQS17
DM/ NU/ CS
RDQS RDQS
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
DQS DQS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
D7
Serial PD
CB0
CB1
CB2
CB3
CB4
CB5
CB6
CB7
DM/ NU/ CS
RDQS RDQS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
D8
DQS DQS
DM/ NU/ CS
RDQS RDQS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
DQS DQS
D17
SCL
SDA
WP A0
A1
A2
SA0 SA1 SA2
DM/ NU/ CS
RDQS RDQS
DQS DQS
D16
VDDSPD
Serial PD
VDD/VDDQ
D0 - D17
VREF
D0 - D17
VSS
D0 - D17
Signals for Address and Command Parity Function (M393T2953CZA)
C0 Register A
C0 Register B
VDD
VSS
C1
C1
VDD
VDD
RSO-> CS : DDR2 SDRAMs D0-D8
PPO
RS1-> CS : DDR2 SDRAMs D9-D17
1:2
PPO
PAR_IN
PAR_IN
PAR_IN
RBA0-RBA1 -> BA0-BA1 : DDR2 SDRAMs D0-D17
R
Err_Out
QERR
QERR
100K ohms
RA0-RA13 -> A0-A13 : DDR2 SDRAMs D0-D17
E
RRAS -> RAS : DDR2 SDRAMs D0-D17
G
The resistors on Par_In, A13, A14, A15, BA2 and the
RCAS -> CAS : DDR2 SDRAMs D0-D17
I
signal line of Err_Out refer to the section: "Register
RWE -> WE : DDR2 SDRAMs D0-D17
S
Options for Unused Address inputs"
RCKE0 -> CKE : DDR2 SDRAMs D0-D8
T
RCKE1 -> CKE : DDR2 SDRAMs D9-D17
E
RODT0 -> ODT0 : DDR2 SDRAMs D0-D8
R
RODT1 -> ODT1 : DDR2 SDRAMs D9-D17
CK0
PCK0-PCK6, PCK8, PCK9 -> CK : DDR2 SDRAMs D0-D17
P
RST
RESET**
L
PCK7**
PCK0-PCK6, PCK8, PCK9 -> CK : DDR2 SDRAMs D0-D17
CK0
L
PCK7**
PCK7 -> CK : Register
OE
RESET
PCK7 -> CK : Register
* S0 connects to DCS and S0 connects to CSR on a Register,
Notes :
S1 connects to DCS and S0 connects to CSR on another Register.
1. DQ-to-I/O wiring may be changed per nibble.
** RESET, PCK7 and PCK7 connects to both Registers.
2. Unless otherwise noted, resister values are 22 Ohms
Other signals connect to one of two Registers.
3. RS0 and RS1 alternate between the back and front sides of the DIMM
S0*
S1*
BA0-BA1
A0-A13
RAS
CAS
WE
CKE0
CKE1
ODT0
ODT1
Rev. 1.2 Aug. 2005
512MB, 1GB, 2GB Registered DIMMs
DDR2 SDRAM
Functional Block Diagram: 1GB, 128Mx72 Module(populated as 1 rank of x4 DDR2 SDRAMs)
M393T2950CZ3 / M393T2950CZA
VSS
RS0
DM0/DQS9
NC/DQS9
DQS0
DQS0
DM
DQ0
DQ1
DQ2
DQ3
DQS1
DQS1
I/O 0
I/O 1
I/O 2
I/O 3
DM
DQ8
DQ9
DQ10
DQ11
I/O 0
I/O 1
I/O 2
I/O 3
CS
DQS DQS
D0
CS
DQS DQS
D1
I/O 0
I/O 1
I/O 2
I/O 3
CS
DQS DQS
I/O 0
I/O 1
I/O 2
I/O 3
CS
DQS DQS
D3
I/O 0
I/O 1
I/O 2
I/O 3
CS
DQS DQS
DQS DQS
D11
CS
I/O 0
I/O 1
I/O 2
I/O 3
DQS DQS
Serial PD
D12
SCL
SDA
WP A0
DM
DQ36
DQ37
DQ38
DQ39
D4
DQS5
DQS5
CS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 0
I/O 1
I/O 2
I/O 3
CS
DQS DQS
DM
DQ44
DQ45
DQ46
DQ47
D5
DQS6
DQS6
I/O 0
I/O 1
I/O 2
I/O 3
CS
DQS DQS
CS
I/O 0
I/O 1
I/O 2
I/O 3
DM
DQ52
DQ53
DQ54
DQ55
D6
DQS7
DQS7
A2
D13
DQS DQS
D14
DM6/DQS15
NC/DQS15
DM
A1
SA0 SA1 SA2
DQS DQS
DM5/DQS14
NC/DQS14
DM
CS
I/O 0
I/O 1
I/O 2
I/O 3
VDDSPD
Serial PD
VDD/VDDQ
D0 - D17
VREF
D0 - D17
VSS
D0 - D17
DQS DQS
D15
DM7DQS16
NC/DQS16
DM
I/O 0
I/O 1
I/O 2
I/O 3
CS
DQS DQS
DM
DQ60
DQ61
DQ62
DQ63
D7
DQS8
DQS8
CS
I/O 0
I/O 1
I/O 2
I/O 3
DQS DQS
D16
DM8/DQS17
NC/DQS17
DM
CB0
CB1
CB2
CB3
CS
DM4/DQS13
NC/DQS13
DM
DQ56
DQ57
DQ58
DQ59
DQS DQS
D10
I/O 0
I/O 1
I/O 2
I/O 3
DM
DQ28
DQ29
DQ30
DQ31
DQS4
DQS4
DQ48
DQ49
DQ50
DQ51
CS
DM3/DQS12
NC/DQS12
DM
DQ40
DQ41
DQ42
DQ43
DQS DQS
D9
I/O 0
I/O 1
I/O 2
I/O 3
DM
DQ20
DQ21
DQ22
DQ23
D2
DQS3
DQS3
DQ32
DQ33
DQ34
DQ35
CS
DM2/DQS11
NC/DQS11
DM
DQ24
DQ25
DQ26
DQ27
I/O 0
I/O 1
I/O 2
I/O 3
DM
DQ12
DQ13
DQ14
DQ15
DQS2
DQS2
DQ16
DQ17
DQ18
DQ19
DM
DQ4
DQ5
DQ6
DQ7
DM1/DQS10
NC/DQS10
I/O 0
I/O 1
I/O 2
I/O 3
CS
D8
DQS DQS
DM
CB4
CB5
CB6
CB7
CS
I/O 0
I/O 1
I/O 2
I/O 3
DQS DQS
D17
Signals for Address and Command Parity Function (M393T2950CZA)
1:2
R
E
G
I
S
T
E
R
S0*
BA0-BA1
A0-A13
RAS
CAS
WE
CKE0
ODT0
RESET**
RSO-> CS : DDR2 SDRAMs D0-D17
RBA0-RBA1 -> BA0-BA1 : DDR2 SDRAMs D0-D17
RA0-RA13 -> A0-A13 : DDR2 SDRAMs D0-D17
RRAS -> RAS : DDR2 SDRAMs D0-D17
RCAS -> CAS : DDR2 SDRAMs D0-D17
RWE -> WE : DDR2 SDRAMs D0-D17
RCKE0 -> CKE : DDR2 SDRAMs D0-D17
RODT0 -> ODT0 : DDR2 SDRAMs D0-D17
VSS
VDD
PAR_IN
C0
C1
Register A
PAR_IN
100K ohms
PPO
VDD
VDD
C0
C1
Register B
PAR_IN
PPO
QERR
QERR
Err_Out
The resistors on Par_In, A13, A14, A15, BA2 and the
signal line of Err_Out refer to the section: "Register
Options for Unused Address inputs"
RST
PCK7**
PCK7**
Notes :
1. DQ-to-I/O wiring may be changed per nibble.
2. Unless otherwise noted, resister values are 22 Ohms
CK0
* S0 connects to DCS of Register1, CSR of Register2. CSR of register 1 and DCS of register 2 connects to VDD.
** RESET, PCK7 and PCK7 connects to both Registers. Other signals connect to one of two Registers.
CK0
RESET
P
L
L
OE
PCK0-PCK6, PCK8, PCK9 -> CK : DDR2 SDRAMs D0-D8
PCK0-PCK6, PCK8, PCK9 -> CK : DDR2 SDRAMs D0-D8
PCK7 -> CK : Register
PCK7 -> CK : Register
Rev. 1.2 Aug. 2005
512MB, 1GB, 2GB Registered DIMMs
DDR2 SDRAM
Functional Block Diagram: 2GB, 256Mx72 Module(populated as 2 rank of x4 DDR2 SDRAMs)
M393T5750CZ3 / M393T5750CZA
VSS
RS1
RS0
DM0/DQS9
NC/DQS9
DQS0
DQS0
DM
DQ0
DQ1
DQ2
DQ3
DQS1
DQS1
DQS DQS
I/O 0
I/O 1 D0
I/O 2
I/O 3
DM
DQ8
DQ9
DQ10
DQ11
CS
CS
DM/
CS
I/O 0
I/O 1 D18
I/O 2
I/O 3
DQS DQS
I/O 0
I/O 1 D1
I/O 2
I/O 3
DM/
CS
DQS DQS
CS
DQS DQS
I/O 0
I/O 1 D2
I/O 2
I/O 3
DM/
CS
CS
DQS DQS
I/O 0
I/O 1 D3
I/O 2
I/O 3
DM
SCL
I/O 0
I/O 1 D27
I/O 2
I/O 3
CS
DQS DQS
I/O 0
I/O 1 D10
I/O 2
I/O 3
DM
DQ20
DQ21
DQ22
DQ23
CS
DQS DQS
CS
DQS DQS
I/O 0
I/O 1 D4
I/O 2
I/O 3
DM
DM
CS
DQS DQS
CS
DQS DQS
DM
CS
DQS DQS
DM
CS
DQS DQS
CS
DQS DQS
DM
CS
DQS DQS
I/O 0
I/O 1 D5
I/O 2
I/O 3
DM
CS
DM
DQS DQS
CS
DQS DQS
I/O 0
I/O 1 D13
I/O 2
I/O 3
VDD/VDDQ
D0 - D35
VREF
D0 - D35
VSS
D0 - D35
Signals for Address and Command
Parity Function (M393T5750CZA)
CS
VSS
VDD
DQS DQS
DM
CS
DQ44
DQ45
DQ46
DQ47
DQS6
DQS6
CS
I/O 0
I/O 1 D14
I/O 2
I/O 3
DM
CS
DQS DQS
PAR_IN
CS
DQS DQS
I/O 0
I/O 1 D6
I/O 2
I/O 3
DM
CS
DQS DQS
DM
DQ52
DQ53
DQ54
DQ55
I/O 0
I/O 1 D24
I/O 2
I/O 3
DQS7
DQS7
CS
DQS DQS
I/O 0
I/O 1 D32
I/O 2
I/O 3
DQS DQS
I/O 0
I/O 1 D15
I/O 2
I/O 3
DM
CS
CS
DQS DQS
I/O 0
I/O 1 D7
I/O 2
I/O 3
DM
CS
DQS DQS
DQS8
DQS8
CS
I/O 0
I/O 1 D8
I/O 2
I/O 3
S0*
DQS DQS
DM
CS
DM
DQS DQS
I/O 0
I/O 1 D26
I/O 2
I/O 3
Register B1
PAR_IN
PPO
Err_Out
VSS
VDD
C0
C1
Register A2
PPO
QERR
VDD
VDD
I/O 0
I/O 1 D33
I/O 2
I/O 3
CS
DQS DQS
DM
CS
DQS DQS
I/O 0
I/O 1 D34
I/O 2
I/O 3
I/O 0
I/O 1 D16
I/O 2
I/O 3
DM8/DQS17
NC/DQS17
DM
C0
C1
C0
C1
Register B2
PAR_IN
PPO
QERR
Register A1 and A2 share the a part of Add/
DQ60
DQ61
DQ62
DQ63
I/O 0
I/O 1 D25
I/O 2
I/O 3
VDD
VDD
PAR_IN
DQS DQS
DM7DQS16
NC/DQS16
DM
PPO
QERR
DM6/DQS15
NC/DQS15
DM
Register A1
QERR
I/O 0
I/O 1 D31
I/O 2
I/O 3
DQS DQS
C0
C1
PAR_IN
100K ohms
DM
I/O 0
I/O 1 D23
I/O 2
I/O 3
A2
Serial PD
I/O 0
I/O 1 D30
I/O 2
I/O 3
DM5/DQS14
NC/DQS14
DM
A1
VDDSPD
I/O 0
I/O 1 D29
I/O 2
I/O 3
I/O 0
I/O 1 D12
I/O 2
I/O 3
DQ36
DQ37
DQ38
DQ39
I/O 0
I/O 1 D22
I/O 2
I/O 3
SDA
WP A0
I/O 0
I/O 1 D28
I/O 2
I/O 3
I/O 0
I/O 1 D11
I/O 2
I/O 3
DQ28
DQ29
DQ30
DQ31
I/O 0
I/O 1 D21
I/O 2
I/O 3
DQS5
DQS5
CB0
CB1
CB2
CB3
DQS DQS
DM4/DQS13
NC/DQS13
DM
DQ56
DQ57
DQ58
DQ59
CS
SA0 SA1 SA2
DM
DQS DQS
DQS4
DQS4
DQ48
DQ49
DQ50
DQ51
DM
DM3/DQS12
NC/DQS12
DM
DQ40
DQ41
DQ42
DQ43
DQS DQS
I/O 0
I/O 1 D9
I/O 2
I/O 3
DQ12
DQ13
DQ14
DQ15
I/O 0
I/O 1 D20
I/O 2
I/O 3
DQS3
DQS3
DQ32
DQ33
DQ34
DQ35
CS
DM2/DQS11
NC/DQS11
DM
DQ24
DQ25
DQ26
DQ27
DM
DQ4
DQ5
DQ6
DQ7
DM1/DQS10
NC/DQS10
I/O 0
I/O 1 D19
I/O 2
I/O 3
DQS2
DQS2
DQ16
DQ17
DQ18
DQ19
Serial PD
DQS DQS
Cmd input signal set.
Register B1 and B2 share the rest part of Add/
Cmd input signal set.
The resistors on Par_In, A13, A14, A15, BA2
DM
CB4
CB5
CB6
CB7
CS
DQS DQS
I/O 0
I/O 1 D17
I/O 2
I/O 3
DM
CS
DQS DQS
I/O 0
I/O 1 D35
I/O 2
I/O 3
and the signal line of Err_Out refer to the section: "Register Options for Unused Address
inputs"
RSO-> CS : DDR2 SDRAMs D0-D17
S1*
BA0-BA1
A0-A13
RAS
CAS
WE
CKE0
CKE1
ODT0
ODT1
RESET**
1:2
R
E
G
I
S
T
E
R
RS1-> CS : DDR2 SDRAMs D18-D35
RBA0-RBA1 -> BA0-BA1 : DDR2 SDRAMs D0-D35
RA0-RA13 -> A0-A13 : DDR2 SDRAMs D0-D35
RRAS -> RAS : DDR2 SDRAMs D0-D35
RCAS -> CAS : DDR2 SDRAMs D0-D35
RWE -> WE : DDR2 SDRAMs D0-D35
RCKE0 -> CKE : DDR2 SDRAMs D0-D17
RCKE1 -> CKE : DDR2 SDRAMs D18-D35
RODT0 -> ODT0 : DDR2 SDRAMs D0-D17
RODT1 -> ODT1 : DDR2 SDRAMs D18-D35
RST
PCK7**
PCK7**
* S0 connects to DCS and S0 connects to CSR on a Register,
S1 connects to DCS and S0 connects to CSR on another Register.
** RESET, PCK7 and PCK7 connects to both Registers.
Other signals connect to one of two Registers.
CK0
CK0
RESET
P
L
L
OE
PCK0-PCK6, PCK8, PCK9 -> CK : DDR2 SDRAMs D0-D35
PCK0-PCK6, PCK8, PCK9 -> CK : DDR2 SDRAMs D0-D35
PCK7 -> CK : Register
PCK7 -> CK : Register
Rev. 1.2 Aug. 2005
512MB, 1GB, 2GB Registered DIMMs
DDR2 SDRAM
Absolute Maximum DC Ratings
Symbol
Parameter
Rating
Units
Notes
Voltage on VDD pin relative to VSS
- 1.0 V ~ 2.3 V
V
1
VDDQ
Voltage on VDDQ pin relative to VSS
- 0.5 V ~ 2.3 V
V
1
VDDL
Voltage on VDDL pin relative to VSS
- 0.5 V ~ 2.3 V
V
1
Voltage on any pin relative to VSS
- 0.5 V ~ 2.3 V
V
1
-55 to +100
°C
1, 2
VDD
VIN, VOUT
TSTG
Storage Temperature
Note :
1. Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Exposure to absolute maximum rating conditions for extended periods may affect reliability.
2. Storage Temperature is the case surface temperature on the center/top side of the DRAM. For the measurement conditions, please refer to JESD51-2
standard.
AC & DC Operating Conditions
Recommended DC Operating Conditions (SSTL - 1.8)
Symbol
Parameter
Rating
Min.
Typ.
Max.
Units
Notes
VDD
Supply Voltage
1.7
1.8
1.9
V
VDDL
Supply Voltage for DLL
1.7
1.8
1.9
V
4
VDDQ
Supply Voltage for Output
1.7
1.8
1.9
V
4
VREF
Input Reference Voltage
0.49*VDDQ
0.50*VDDQ
0.51*VDDQ
mV
1,2
Termination Voltage
VREF-0.04
VREF
VREF+0.04
V
3
VTT
Note : There is no specific device VDD supply voltage requirement for SSTL-1.8 compliance. However under all conditions VDDQ must be less than or equal
to VDD.
1. The value of VREF may be selected by the user to provide optimum noise margin in the system. Typically the value of VREF is expected to be about 0.5
x VDDQ of the transmitting device and VREF is expected to track variations in VDDQ.
2. Peak to peak AC noise on VREF may not exceed +/-2% VREF(DC).
3. VTT of transmitting device must track VREF of receiving device.
4. AC parameters are measured with VDD, VDDQ and VDDL tied together.
Rev. 1.2 Aug. 2005
512MB, 1GB, 2GB Registered DIMMs
DDR2 SDRAM
Operating Temperature Condition
Symbol
Parameter
Rating
Units
Notes
TOPER
Operating Temperature
0 to 95
°C
1, 2, 3
Note :
1. Operating Temperature is the case surface temperature on the center/top side of the DRAM. For the measurement conditions, please refer to JESD51.2
standard.
2. At 85 - 95 ×C operation temperature range, doubling refresh commands in frequency to a 32ms period ( tREFI=3.9 us ) is required, and to enter to self
refresh mode at this temperature range, an EMRS command is required to change internal refresh rate.
Input DC Logic Level
Symbol
Parameter
Min.
Max.
Units
VIH(DC)
DC input logic high
VREF + 0.125
VDDQ + 0.3
V
VIL(DC)
DC input logic low
- 0.3
VREF - 0.125
V
Notes
Input AC Logic Level
Symbol
Parameter
VIH(AC)
VIL(AC)
DDR2-400, DDR2-533
DDR2-667, DDR2-800
Min.
Max.
Min.
AC input logic high
VREF + 0.250
-
VREF + 0.200
AC input logic low
-
VREF - 0.250
Units
Max.
V
VREF - 0.200
V
AC Input Test Conditions
Symbol
VREF
VSWING(MAX)
SLEW
Condition
Input reference voltage
Value
Units
Notes
0.5 * VDDQ
V
1
Input signal maximum peak to peak swing
1.0
V
1
Input signal minimum slew rate
1.0
V/ns
2, 3
Notes:
1. Input waveform timing is referenced to the input signal crossing through the VIH/IL(AC) level applied to the device under test.
2. The input signal minimum slew rate is to be maintained over the range from VREF to VIH(AC) min for rising edges and the range from VREF to VIL(AC)
max for falling edges as shown in the below figure.
3. AC timings are referenced with input waveforms switching from VIL(AC) to VIH(AC) on the positive transitions and VIH(AC) to VIL(AC) on the negative
transitions.
VDDQ
VIH(AC) min
VIH(DC) min
VSWING(MAX)
VREF
VIL(DC) max
VIL(AC) max
delta TF
Falling Slew =
delta TR
VREF - VIL(AC) max
delta TF
Rising Slew =
VSS
VIH(AC) min - VREF
delta TR
< AC Input Test Signal Waveform >
Rev. 1.2 Aug. 2005
512MB, 1GB, 2GB Registered DIMMs
DDR2 SDRAM
IDD Specification Parameters Definition
(IDD values are for full operating range of Voltage and Temperature)
Symbol
Proposed Conditions
Units
IDD0
Operating one bank active-precharge current;
tCK = tCK(IDD), tRC = tRC(IDD), tRAS = tRASmin(IDD); CKE is HIGH, CS\ is HIGH between valid commands;
Address bus inputs are SWITCHING; Data bus inputs are SWITCHING
mA
IDD1
Operating one bank active-read-precharge current;
IOUT = 0mA; BL = 4, CL = CL(IDD), AL = 0; tCK = tCK(IDD), tRC = tRC (IDD), tRAS = tRASmin(IDD), tRCD =
tRCD(IDD); CKE is HIGH, CS\ is HIGH between valid commands; Address bus inputs are SWITCHING; Data pattern
is same as IDD4W
mA
IDD2P
Precharge power-down current;
All banks idle; tCK = tCK(IDD); CKE is LOW; Other control and address bus inputs are STABLE; Data bus inputs are
FLOATING
mA
IDD2Q
Precharge quiet standby current;
All banks idle; tCK = tCK(IDD); CKE is HIGH, CS\ is HIGH; Other control and address bus inputs are STABLE; Data
bus inputs are FLOATING
mA
IDD2N
Precharge standby current;
All banks idle; tCK = tCK(IDD); CKE is HIGH, CS\ is HIGH; Other control and address bus inputs are SWITCHING;
Data bus inputs are SWITCHING
mA
IDD3P
Active power-down current;
All banks open; tCK = tCK(IDD); CKE is LOW; Other control and address bus
inputs are STABLE; Data bus inputs are FLOATING
Fast PDN Exit MRS(12) = 0mA
mA
Slow PDN Exit MRS(12) = 1mA
mA
IDD3N
Active standby current;
All banks open; tCK = tCK(IDD), tRAS = tRASmax(IDD), tRP = tRP(IDD); CKE is HIGH, CS\ is HIGH between valid
commands; Other control and address bus inputs are SWITCHING; Data bus inputs are SWITCHING
mA
IDD4W
Operating burst write current;
All banks open, Continuous burst writes; BL = 4, CL = CL(IDD), AL = 0; tCK = tCK(IDD), tRAS = tRASmax(IDD), tRP =
tRP(IDD); CKE is HIGH, CS\ is HIGH between valid commands; Address bus inputs are SWITCHING; Data bus inputs
are SWITCHING
mA
IDD4R
Operating burst read current;
All banks open, Continuous burst reads, IOUT = 0mA; BL = 4, CL = CL(IDD), AL = 0; tCK = tCK(IDD), tRAS = tRASmax(IDD), tRP = tRP(IDD); CKE is HIGH, CS\ is HIGH between valid commands; Address bus inputs are SWITCHING; Data pattern is same as IDD4W
mA
IDD5B
Burst auto refresh current;
tCK = tCK(IDD); Refresh command at every tRFC(IDD) interval; CKE is HIGH, CS\ is HIGH between valid commands;
Other control and address bus inputs are SWITCHING; Data bus inputs are SWITCHING
mA
IDD6
Self refresh current;
CK and CK\ at 0V; CKE ≤ 0.2V; Other control and address bus inputs are
FLOATING; Data bus inputs are FLOATING
IDD7
Operating bank interleave read current;
All bank interleaving reads, IOUT = 0mA; BL = 4, CL = CL(IDD), AL = tRCD(IDD)-1*tCK(IDD); tCK = tCK(IDD), tRC =
tRC(IDD), tRRD = tRRD(IDD), tFAW = tFAW(IDD), tRCD = 1*tCK(IDD); CKE is HIGH, CS\ is HIGH between valid
commands; Address bus inputs are STABLE during DESELECTs; Data pattern is same as IDD4R; Refer to the following page for detailed timing conditions
Normal
mA
Low Power
mA
Notes
mA
Rev. 1.2 Aug. 2005
512MB, 1GB, 2GB Registered DIMMs
DDR2 SDRAM
Operating Current Table(1-1) (TA=0oC, VDD= 1.9V)
M393T6553CZ3 / M393T6553CZA : 512MB(64Mx8 *9) Module
Symbol
E7(800@CL=5)
E6(667@CL=5)
D5(533@CL=4)
CC(400@CL=3)
Unit
IDD0
TBD
TBD
1,240
1,130
mA
IDD1
TBD
TBD
1,405
1,285
mA
IDD2P
TBD
TBD
562
522
mA
IDD2Q
TBD
TBD
760
710
mA
IDD2N
TBD
TBD
775
715
mA
IDD3P-F
TBD
TBD
750
720
mA
IDD3P-S
TBD
TBD
348
338
mA
IDD3N
TBD
TBD
1,000
930
mA
IDD4W
TBD
TBD
1,620
1,410
mA
IDD4R
TBD
TBD
1,525
1,340
mA
IDD5B
TBD
TBD
1,780
1,720
mA
IDD6*
TBD
TBD
72
72
mA
IDD7
TBD
TBD
2,660
2,570
mA
Notes
* IDD6 = DRAM current + standby current of PLL and Register
** Module IDD was calculated on the basis of component IDD and can be differently measured according to DQ loading cap.
M393T2953CZ3 / M393T2953CZA : 1GB(64Mx8 *18) Module
Symbol
E7(800@CL=5)
E6(667@CL=5)
D5(533@CL=4)
CC(400@CL=3)
Unit
IDD0
TBD
TBD
1,655
1,575
mA
IDD1
TBD
TBD
1,830
1,770
mA
mA
IDD2P
TBD
TBD
784
724
IDD2Q
TBD
TBD
1,200
1,130
mA
IDD2N
TBD
TBD
1,180
1,150
mA
IDD3P-F
TBD
TBD
1,190
1,130
mA
IDD3P-S
TBD
TBD
546
516
mA
mA
IDD3N
TBD
TBD
1,345
1,325
IDD4W
TBD
TBD
2,065
1,865
mA
IDD4R
TBD
TBD
1,970
1,785
mA
IDD5B
TBD
TBD
2,215
2,125
mA
IDD6*
TBD
TBD
144
144
mA
IDD7
TBD
TBD
3,335
3,095
mA
Notes
* IDD6 = DRAM current + standby current of PLL and Register
** Module IDD was calculated on the basis of component IDD and can be differently measured according to DQ loading cap.
Rev. 1.2 Aug. 2005
512MB, 1GB, 2GB Registered DIMMs
DDR2 SDRAM
Operating Current Table(1-2) (TA=0oC, VDD= 1.9V)
M393T2950CZ3 / M393T2950CZA : 1GB(128Mx4 *18) Module
Symbol
E7(800@CL=5)
E6(667@CL=5)
D5(533@CL=4)
CC(400@CL=3)
Unit
IDD0
TBD
TBD
2,060
1,980
mA
mA
IDD1
TBD
TBD
2,370
2,310
IDD2P
TBD
TBD
784
724
mA
IDD2Q
TBD
TBD
1,200
1,130
mA
IDD2N
TBD
TBD
1,180
1,150
mA
IDD3P-F
TBD
TBD
1,190
1,130
mA
IDD3P-S
TBD
TBD
546
516
mA
IDD3N
TBD
TBD
1,480
1,460
mA
IDD4W
TBD
TBD
2,650
2,360
mA
IDD4R
TBD
TBD
2,600
2,370
mA
IDD5B
TBD
TBD
3,160
3,070
mA
IDD6*
TBD
TBD
144
144
mA
IDD7
TBD
TBD
5,000
4,760
mA
Notes
* IDD6 = DRAM current + standby current of PLL and Register
** Module IDD was calculated on the basis of component IDD and can be differently measured according to DQ loading cap.
M393T5750CZ3 / M393T5750CZA : 2GB(128Mx4 *36) Module
Symbol
E7(800@CL=5)
E6(667@CL=5)
D5(533@CL=4)
CC(400@CL=3)
Unit
IDD0
TBD
TBD
2,980
2,830
mA
IDD1
TBD
TBD
3,340
3,220
mA
IDD2P
TBD
TBD
1,238
1,138
mA
IDD2Q
TBD
TBD
2,060
1,950
mA
IDD2N
TBD
TBD
2,030
1,990
mA
IDD3P-F
TBD
TBD
2,050
1,950
mA
IDD3P-S
TBD
TBD
922
872
mA
IDD3N
TBD
TBD
2,350
2,320
mA
IDD4W
TBD
TBD
3,630
3,240
mA
IDD4R
TBD
TBD
3,430
3,160
mA
IDD5B
TBD
TBD
4,090
3,940
mA
IDD6*
TBD
TBD
288
288
mA
IDD7
TBD
TBD
6,330
5,880
mA
Notes
* IDD6 = DRAM current + standby current of PLL and Register
** Module IDD was calculated on the basis of component IDD and can be differently measured according to DQ loading cap.
Rev. 1.2 Aug. 2005
512MB, 1GB, 2GB Registered DIMMs
DDR2 SDRAM
Input/Output Capacitance(VDD=1.8V, VDDQ=1.8V, TA=25oC)
Parameter
Part-Number
Min
Symbol
Max
M393T6553CZ3
M393T6553CZA
Min
Max
M393T2953CZ3
M393T2953CZA
Min
Max
M393T2950CZ3
M393T2950CZA
Min
Max
M393T5750CZ3
M393T5750CZA
Input capacitance, CK and CK
CCK
-
11
-
11
-
11
-
11
Input capacitance, CKE and CS
CI1
-
12
-
12
-
12
-
12
Input capacitance, Addr,RAS,CAS,WE
CI2
-
12
-
12
-
12
-
12
Input/output capacitance, DQ, DM, DQS, DQS
CIO
-
10
-
10
-
10
-
10
Units
pF
* DM is internally loaded to match DQ and DQS identically.
Rev. 1.2 Aug. 2005
512MB, 1GB, 2GB Registered DIMMs
DDR2 SDRAM
Electrical Characteristics & AC Timing for DDR2-800/667/533/400
(0 °C < TOPER < 95 °C; VDDQ = 1.8V + 0.1V; VDD = 1.8V + 0.1V)
Refresh Parameters by Device Density
Parameter
Symbol
Refresh to active/Refresh command time
tRFC
Average periodic refresh interval
tREFI
256Mb
512Mb
1Gb
2Gb
4Gb
Units
75
105
127.5
195
327.5
ns
0 °C ≤ TCASE ≤ 85°C
7.8
7.8
7.8
7.8
7.8
µs
85 °C < TCASE ≤ 95°C
3.9
3.9
3.9
3.9
3.9
µs
Speed Bins and CL, tRCD, tRP, tRC and tRAS for Corresponding Bin
Speed
DDR2-800(E7)
DDR2-667(E6)
DDR2-533(D5)
DDR2-400(CC)
Bin(CL - tRCD - tRP)
5-5-5
5-5-5
4-4-4
3-3-3
Units
Parameter
min
max
min
max
min
max
min
max
tCK, CL=3
5
8
5
8
5
8
5
8
ns
tCK, CL=4
3.75
8
3.75
8
3.75
8
5
8
ns
tCK, CL=5
2.5
8
3
8
3.75
8
-
-
ns
tRCD
12.5
-
15
-
15
-
15
-
ns
tRP
12.5
-
15
-
15
-
15
-
ns
tRC
51.5
-
54
-
55
-
55
-
ns
tRAS
39
70000
39
70000
40
70000
40
70000
ns
Timing Parameters by Speed Grade
(Refer to notes for informations related to this table at the bottom)
Parameter
Symbol
DDR2-800
min
max
DDR2-667
min
max
DDR2-533
DDR2-400
min
max
min
max
Units
DQ output access time from CK/CK
tAC
- 400
400
-450
+450
-500
+500
-600
+600
ps
DQS output access time from CK/CK
tDQSCK
- 350
350
-400
+400
-450
+450
-500
+500
ps
CK high-level width
tCH
0.45
0.55
0.45
0.55
0.45
0.55
0.45
0.55
tCK
CK low-level width
tCL
0.45
0.55
0.45
0.55
0.45
0.55
0.45
0.55
tCK
CK half period
tHP
min(tCL,t
CH)
x
min(tCL,
tCH)
x
min(tCL,
tCH)
x
min(tCL,
tCH)
x
ps
Clock cycle time, CL=x
tCK
2500
8000
3000
8000
3750
8000
5000
8000
ps
DQ and DM input hold time
tDH(base)
125
x
175
x
225
x
275
x
ps
DQ and DM input setup time
tDS(base)
50
x
100
x
100
x
150
x
ps
Control & Address input pulse width for
each input
tIPW
0.6
x
0.6
x
0.6
x
0.6
x
tCK
0.35
x
0.35
x
0.35
x
0.35
x
tCK
x
tAC max
x
tAC max
x
tAC max
x
tAC max
ps
DQ and DM input pulse width for each input tDIPW
Data-out high-impedance time from CK/CK tHZ
DQS low-impedance time from CK/CK
tLZ(DQS)
tAC min
tAC max
tAC min
tAC max
tAC min
tAC max
tAC min
tAC max
ps
DQ low-impedance time from CK/CK
tLZ(DQ)
2* tAC
min
tAC max
2*tAC
min
tAC max
2* tACmin
tAC max
2* tACmin
tAC max
ps
DQS-DQ skew for DQS and associated DQ
tDQSQ
signals
x
200
x
240
x
300
x
350
ps
DQ hold skew factor
tQHS
x
300
x
340
x
400
x
450
ps
DQ/DQS output hold time from DQS
tQH
tHP tQHS
x
tHP tQHS
x
tHP tQHS
x
tHP tQHS
x
ps
First DQS latching transition to associated
clock edge
tDQSS
- 0.25
0.25
-0.25
0.25
-0.25
0.25
-0.25
0.25
tCK
Notes
Rev. 1.2 Aug. 2005
512MB, 1GB, 2GB Registered DIMMs
Parameter
Symbol
DDR2-800
DDR2 SDRAM
DDR2-667
DDR2-533
DDR2-400
min
max
min
max
min
max
min
max
Units
DQS input high pulse width
tDQSH
0.35
x
0.35
x
0.35
x
0.35
x
tCK
DQS input low pulse width
tDQSL
0.35
x
0.35
x
0.35
x
0.35
x
tCK
DQS falling edge to CK setup time
tDSS
0.2
x
0.2
x
0.2
x
0.2
x
tCK
DQS falling edge hold time from CK
tDSH
0.2
x
0.2
x
0.2
x
0.2
x
tCK
Mode register set command cycle time
tMRD
2
x
2
x
2
x
2
x
tCK
Write postamble
tWPST
0.4
0.6
0.4
0.6
0.4
0.6
0.4
0.6
tCK
Write preamble
tWPRE
0.35
x
0.35
x
0.35
x
0.35
x
tCK
Address and control input hold time
tIH(base)
250
x
275
x
375
x
475
x
ps
Address and control input setup time
tIS(base)
175
x
200
x
250
x
350
x
ps
Read preamble
tRPRE
0.9
1.1
0.9
1.1
0.9
1.1
0.9
1.1
tCK
Read postamble
tRPST
0.4
0.6
0.4
0.6
0.4
0.6
0.4
0.6
tCK
Active to active command period for 1KB
page size products
tRRD
7.5
x
7.5
x
7.5
x
7.5
x
ns
Active to active command period for 2KB
page size products
tRRD
10
x
10
x
10
x
10
x
ns
Four Activate Window for 1KB page size
products
tFAW
35
37.5
37.5
37.5
ns
Four Activate Window for 2KB page size
products
tFAW
45
50
50
50
ns
CAS to CAS command delay
tCCD
2
x
2
2
2
tCK
Write recovery time
tWR
15
x
15
x
15
x
15
x
ns
WR+tRP
x
WR+tRP
x
WR+tRP
x
WR+tRP
x
tCK
x
7.5
x
10
x
ns
Auto precharge write recovery + precharge
tDAL
time
Internal write to read command delay
tWTR
7.5
7.5
Internal read to precharge command delay tRTP
7.5
7.5
7.5
7.5
ns
Exit self refresh to a non-read command
tXSNR
tRFC + 10
tRFC + 10
tRFC + 10
tRFC + 10
ns
Exit self refresh to a read command
tXSRD
200
x
200
200
200
tCK
Exit precharge power down to any nonread command
tXP
2
x
2
x
2
x
2
x
tCK
Exit active power down to read command
tXARD
2
x
2
x
2
x
2
x
tCK
Exit active power down to read command
(slow exit, lower power)
tXARDS
CKE minimum pulse width
(high and low pulse width)
ODT turn-on delay
8 - AL
7 - AL
6 - AL
6 - AL
tCKE
3
3
3
3
tAOND
2
2
tAC(max)
+ 0.7
2
2
tAC(min)
tAC(max)
+0.7
2
2
tAC(min)
tAC(max)
+1
tCK
tCK
2
2
tCK
tAC(min)
tAC(max)
+1
ns
ns
ODT turn-on
tAON
tAC(min)
ODT turn-on(Power-Down mode)
tAONPD
2tCK +
tAC(min)+ 2tCK+tAC tAC(min)+ 2tCK+tAC tAC(min)+ 2tCK+tAC
tAC(min)+
tAC(max)
2
(max)+1
2
(max)+1
2
(max)+1
2
+1
ODT turn-off delay
tAOFD
2.5
2.5
tAC(max)
+ 0.6
2.5
2.5
2.5
2.5
2.5
2.5
tCK
tAC(min)
tAC(max)
+ 0.6
tAC(min)
tAC(max)+
0.6
tAC(min)
ODT turn-off
tAOF
tAC(min)
tAC(max)+
0.6
ns
ODT turn-off (Power-Down mode)
tAOFPD
2.5tCK+
2.5tCK+
2.5tCK +
tAC(min)+
tAC(min)+ 2.5tCK+tA tAC(min)+
tAC(min)+
tAC(max)
tAC(max)
tAC(max)
2
2
C(max)+1
2
2
+1
+1
+1
ns
ODT to power down entry latency
tANPD
3
3
3
3
tCK
ODT power down exit latency
tAXPD
8
8
8
8
tCK
OCD drive mode output delay
tOIT
0
Minimum time clocks remains ON after
CKE asynchronously drops LOW
tDelay
tIS+tCK
+tIH
12
0
tIS+tCK
+tIH
12
0
tIS+tCK
+tIH
12
0
tIS+tCK
+tIH
Notes
12
ns
ns
Rev. 1.2 Aug. 2005
512MB, 1GB, 2GB Registered DIMMs
DDR2 SDRAM
Physical Dimensions: 64Mbx8 based 64Mx72 Module(1 Rank)
M393T6553CZ3 / M393T6553CZA
Units : Millimeters
2.70
Register
133.35
30.00
PLL
1.0 max
1.27 ± 0.10
A
B
63.00
4.00
4.00
3.00
2.50±0.20
5.00
55.00
0.80±0.05
3.80
2.50
1.50±0.10
Detail A
0.20
1.00
4.00
Detail B
The used device is 64M x8 DDR2 SDRAM, FBGA.
DDR2 SDRAM Part NO : K4T51083QC
Rev. 1.2 Aug. 2005
512MB, 1GB, 2GB Registered DIMMs
DDR2 SDRAM
Physical Dimensions: 64Mbx8/128Mbx4 based 128Mx72 Module(2/1 Ranks)
M393T2953CZ3 / M393T2953CZA
M393T2950CZ3 / M393T2950CZA
Units : Millimeters
133.35
Register
4.00
30.00
PLL
1.0 max
1.7 max
1.27 ± 0.10
A
B
63.00
Register
55.00
4.00
4.00
3.00
2.50±0.20
5.00
0.80±0.05
3.80
2.50
1.50±0.10
Detail A
0.20
1.00
4.00
Detail B
The used device is 64M x8 / 128M x4 DDR2 SDRAM, FBGA.
DDR2 SDRAM Part NO : K4T51083QC / K4T51043QC
Rev. 1.2 Aug. 2005
512MB, 1GB, 2GB Registered DIMMs
DDR2 SDRAM
Physical Dimensions: 128Mbx4 based 256Mx72 Module(2 Ranks)
M393T5750CZ3 / M393T5750CZA
Units : Millimeters
133.35
PLL
Register
Register
4.00
30.00
1.0 max
1.7 max
1.27 ± 0.10
A
B
63.00
5.00
4.00
4.00
3.00
2.50±0.20
Register
Register
55.00
0.80±0.05
3.80
2.50
1.50±0.10
Detail A
0.20
1.00
4.00
Detail B
The used device is 128M x4 DDR2 SDRAM, FBGA.
DDR2 SDRAM Part NO : K4T51043QC
Rev. 1.2 Aug. 2005
512MB, 1GB, 2GB Registered DIMMs
DDR2 SDRAM
240 Pin DDR2 Registered DIMM Clock Topology
0ns (nominal)
PLL
DDR2 SDRAM
120 ohms
OUT1
CK0
120 ohms
IN
DDR2 SDRAM
CK0
Reg.A
120 ohms
C
OUTN
C
Feedback In
Feedback Out
120 ohms
Reg.B
Note:
1.
2.
3.
4.
The clock delay from the input of the PLL clock to the input of any DDR2 SDRAM or register will be set to 0ns (nominal).
Input, output, and feedback clock lines are terminated from line to line as shown, and not from line to ground.
Only one PLL output is shown per output type. Any additional PLL outputs will be wired in a similar manner.
Termination resistors for the PLL feedback path clocks are located as close to the input pin of the PLL as possible.
Rev. 1.2 Aug. 2005
512MB, 1GB, 2GB Registered DIMMs
DDR2 SDRAM
Revision History
Revision 1.0 (Apr. 2005)
- Initial Release
Revision 1.1 (Jul. 2005)
- Revised the Ordering Information
Revision 1.2 (Aug. 2005)
- Revised the IDD Current Values
Rev. 1.2 Aug. 2005
Similar pages