Samsung M470T2953BSY0-CD5/CC 200pin unbuffered sodimm based on 512mb b-die 64bit non-ecc Datasheet

256MB, 512MB, 1GB Unbuffered SODIMMs
DDR2 SDRAM
DDR2 Unbuffered SODIMM
200pin Unbuffered SODIMM based on 512Mb B-die
64bit Non-ECC
INFORMATION IN THIS DOCUMENT IS PROVIDED IN RELATION TO SAMSUNG PRODUCTS,
AND IS SUBJECT TO CHANGE WITHOUT NOTICE.
NOTHING IN THIS DOCUMENT SHALL BE CONSTRUED AS GRANTING ANY LICENSE,
EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE,
TO ANY INTELLECTUAL PROPERTY RIGHTS IN SAMSUNG PRODUCTS OR TECHNOLOGY. ALL
INFORMATION IN THIS DOCUMENT IS PROVIDED
ON AS "AS IS" BASIS WITHOUT GUARANTEE OR WARRANTY OF ANY KIND.
1. For updates or additional information about Samsung products, contact your nearest Samsung office.
2. Samsung products are not intended for use in life support, critical care, medical, safety equipment, or similar
applications where Product failure couldresult in loss of life or personal or physical harm, or any military or
defense application, or any governmental procurement to which special terms or provisions may apply.
* Samsung Electronics reserves the right to change products or specification without notice.
Rev. 1.5 Aug. 2005
256MB, 512MB, 1GB Unbuffered SODIMMs
DDR2 SDRAM
DDR2 Unbuffered SODIMM Ordering Information
Part Number
Density
Organization
Component Composition
Number of
Rank
Height
M470T3354BG(Z)3-CD5/CC
256MB
32Mx64
32Mx16(K4T51163QB)*4
1
30mm
M470T3354BG(Z)0-CD5/CC
256MB
32Mx64
32Mx16(K4T51163QB)*4
1
30mm
M470T3354BZ3-LD5/CC
256MB
32Mx64
32Mx16(K4T51163QB)*4
1
30mm
M470T3354BZ0-LD5/CC
256MB
32Mx64
32Mx16(K4T51163QB)*4
1
30mm
M470T6554BG(Z)3-CD5/CC
512MB
64Mx64
32Mx16(K4T51163QB)*8
2
30mm
M470T6554BG(Z)0-CD5/CC
512MB
64Mx64
32Mx16(K4T51163QB)*8
2
30mm
M470T6554BZ3-LD5/CC
512MB
64Mx64
32Mx16(K4T51163QB)*8
2
30mm
M470T6554BZ0-LD5/CC
512MB
64Mx64
32Mx16(K4T51163QB)*8
2
30mm
M470T2953BS(Y)3-CD5/CC
1GB
128Mx64
64Mx8(K4T51083QB)*16
2
30mm
M470T2953BS(Y)0-CD5/CC
1GB
128Mx64
64Mx8(K4T51083QB)*16
2
30mm
M470T2953BY3-LD5/CC
1GB
128Mx64
64Mx8(K4T51083QB)*16
2
30mm
M470T2953BY0-LD5/CC
1GB
128Mx64
64Mx8(K4T51083QB)*16
2
30mm
Note: “Z” and “Y” of Part number(11th digit) stand for Lead-free products.
Note: “3” of Part number(12th digit) stand for Dummy Pad PCB products.
Features
• Performance range
D5(DDR2-533)
CC(DDR2-400)
Unit
Speed@CL3
400
400
Mbps
Speed@CL4
533
400
Mbps
CL-tRCD-tRP
4-4-4
3-3-3
CK
• JEDEC standard 1.8V ± 0.1V Power Supply
• VDDQ = 1.8V ± 0.1V
• 200 MHz fCK for 400Mb/sec/pin, 267MHz fCK for 533Mb/sec/pin
• 4 Banks
• Posted CAS
• Programmable CAS Latency: 3, 4, 5
• Programmable Additive Latency: 0, 1 , 2 , 3 and 4
• Write Latency(WL) = Read Latency(RL) -1
• Burst Length: 4 , 8(Interleave/nibble sequential)
• Programmable Sequential / Interleave Burst Mode
• Bi-directional Differential Data-Strobe (Single-ended data-strobe is an optional feature)
• Off-Chip Driver(OCD) Impedance Adjustment
• On Die Termination
• Average Refresh Period 7.8us at lower than a TCASE 85°C, 3.9us at 85°C < TCASE < 95 °C
- support High Temperature Self-Refresh rate enable feature
• Package: 60ball FBGA - 64Mx8 , 84ball FBGA - 32Mx16
• All of Lead-free products are compliant for RoHS
Note: For detailed DDR2 SDRAM operation, please refer to Samsung’s Device operation & Timing diagram.
Address Configuration
Organization
Row Address
Column Address
Bank Address
Auto Precharge
64Mx8(512Mb) based Module
A0-A13
A0-A9
BA0-BA1
A10
32Mx16(512Mb) based Module
A0-A12
A0-A9
BA0-BA1
A10
Rev. 1.5 Aug. 2005
256MB, 512MB, 1GB Unbuffered SODIMMs
DDR2 SDRAM
Pin Configurations (Front side/Back side)
Pin
Front
Pin
Back
Pin
Front
Pin
Back
Pin
Front
Pin
Back
Pin
Front
Pin
Back
1
VREF
2
VSS
51
DQS2
52
DM2
101
A1
102
A0
151
DQ42
152
DQ46
3
VSS
4
DQ4
53
VSS
54
VSS
103
VDD
104
VDD
153
DQ43
154
DQ47
5
DQ0
6
DQ5
55
DQ18
56
DQ22
105
A10/AP
106
BA1
155
VSS
156
VSS
7
DQ1
8
VSS
57
DQ19
58
DQ23
107
BA0
108
RAS
157
DQ48
158
DQ52
DQ53
9
VSS
10
DM0
59
VSS
60
VSS
109
WE
110
S0
159
DQ49
160
11
DQS0
12
VSS
61
DQ24
62
DQ28
111
VDD
112
VDD
161
VSS
162
VSS
13
14
DQ6
63
CAS
114
ODT0
163
CK1
65
66
115
NC/S1
116
A13
165
NC, TEST
VSS
164
DQ7
DQ29
VSS
113
16
DQ25
VSS
64
15
DQS0
VSS
166
CK1
17
DQ2
18
VSS
67
DM3
68
DQS3
117
VDD
118
VDD
167
DQS6
168
VSS
19
20
DQ12
69
121
122
171
DQS6
VSS
170
72
NC
VSS
169
71
NC/ODT1
VSS
120
DQ13
DQS3
VSS
119
22
NC
VSS
70
21
DQ3
VSS
DM6
VSS
23
DQ8
24
VSS
73
DQ26
74
DQ30
123
DQ32
124
DQ36
173
DQ50
174
DQ54
25
26
DQ27
VSS
76
DQ31
VSS
125
DQ37
VSS
175
177
DQ51
VSS
176
127
DQ33
VSS
126
28
DM1
VSS
75
27
DQ9
VSS
DQ55
VSS
29
DQS1
30
CK0
79
80
DQS4
130
DQ56
180
DQ60
32
CK0
81
131
DQS4
132
DM4
VSS
179
DQS1
NC/CKE1
VDD
129
31
CKE0
VDD
181
DQ57
182
DQ61
77
78
82
128
172
178
33
VSS
34
VSS
83
NC
84
NC
133
VSS
134
DQ38
183
VSS
184
VSS
35
DQ10
36
DQ14
85
86
DQ34
136
DQS7
DQ15
87
88
137
DQ35
138
187
DM7
VSS
186
38
DQ39
VSS
185
DQ11
NC
VDD
135
37
BA2
VDD
188
DQS7
39
VSS
40
VSS
89
A12
90
A11
139
VSS
140
DQ44
189
DQ58
190
VSS
41
VSS
42
VSS
91
A9
92
A7
141
DQ40
142
DQ45
191
DQ59
192
DQ62
43
DQ16
44
DQ20
93
A8
94
A6
143
DQ41
144
VSS
193
VSS
194
DQ63
45
DQ17
46
DQ21
95
VDD
96
VDD
145
VSS
146
DQS5
195
SDA
196
VSS
47
VSS
48
VSS
97
A5
98
A4
147
DM5
148
DQS5
197
SCL
198
SA0
49
DQS2
50
NC
99
A3
100
A2
149
VSS
150
VSS
199
VDDSPD
200
SA1
Note : NC = No Connect; NC, TEST(pin 163)is for bus analysis tool and is not connected on normal memory modules.
Pin Description
Pin Name
Function
CK0,CK1
Clock Inputs, positive line
CK0,CK1
Clock Inputs, negative line
CKE0,CKE1
Clock Enables
Pin Name
SDA
SA1,SA0
Function
SPD Data Input/Output
SPD address
DQ0~DQ63
Data Input/Output
DM0~DM7
Data Masks
RAS
Row Address Strobe
CAS
Column Address Strobe
DQS0~DQS7
Data strobes
WE
Write Enable
DQS0~DQS7
Data strobes complement
S0,S1
Chip Selects
TEST
A0~A9, A11~A13
A10/AP
BA0,BA1
ODT0,ODT1
SCL
Logic Analyzer specific test pin (No connect on So-DIMM)
Address Inputs
VDD
Core and I/O Power
Address Input/Autoprecharge
VSS
Ground
VREF
Input/Output Reference
SDRAM Bank Address
On-die termination control
Serial Presence Detect(SPD) Clock Input
VDDSPD
NC
SPD Power
Spare pins, No connect
Rev. 1.5 Aug. 2005
256MB, 512MB, 1GB Unbuffered SODIMMs
DDR2 SDRAM
Input/Output Functional Description
Symbol
Type
Function
CK0-CK1
CK0-CK1
Input
The system clock inputs. All address and command lines are sampled on the cross point of the rising edge of CK and falling
edge of CK . A Delay Locked Loop (DLL) circuit is driven from the clock input and output timing for read operations is synchronized to the input clock.
CKE0-CKE1
Input
Activates the DDR2 SDRAM CK signal when high and deactivates the CK signal when low, By deactivating the clocks, CKE
low initiates the Power Down mode or the Self Refesh mode.
S0-S1
Input
Enables the associated DDR2 SDRAM command decoder when low and disables the command decoder when high. When
the command decoder is disabled, new commands are ignored but previous operations continue. Rank 0 is selected by S0,
Rank 1 is selected by S1. Ranks are also called “Physical banks”.
RAS, CAS, WE
Input
When sampled at the cross point of the rising edge of CK and falling edge of CK, CAS, RAS, and WE define the operation
to be executed by the SDRAM.
BA0~BA1
Input
Selects which DDR2 SDRAM internal bank is activated.
ODT0~ODT1
Input
Asserts on-die termination for DQ, DM, DQS, and DQS signals if enabled via the DDR2 SDRAM Extended Mode Register
Set (EMRS).
A0~A9,
A10/AP,
A11~A13
Input
During a Bank Activate command cycle, defines the row address when sampled at the cross point of the rising edge of CK
and falling edge of CK. During a Read or Write command cycle, defines the column address when sampled at the cross
point of the rising edge of CK and falling edge of CK. In addition to the column address, AP is used to invoke autoprecharge
operation at the end of the burst read or write cycle. If AP is high, autoprecharge is selected and BA0-BAn defines the bank
to be precharged. If AP is low, autoprecharge is disabled. During a Precharge command cycle, AP is used in conjunction
with BA0-BAn to control which bank(s) to precharge. If AP is high, all banks will be pecharged regardiess of the state of
BA0-BAn inputs. If AP is low, then BA0-BAn are used to define which bank to precharge.
DQ0~DQ63
In/Out
Data Input/Output pins.
DM0~DM7
Input
The data write masks, associated with one data byte. In Write mode, DM operates as a byte
mask by allowing input data to be written if it is low but blocks the write operation if it is high. In
Read mode, DM lines have no effect.
DQS0~DQS7
DQS0~DQS7
In/Out
The data strobes, associated with one data byte, sourced with data transfers. In Write mode,
the data strobe is sourced by the controller and is centered in the data window. In Read mode,
the data strobe is sourced by the DDR2 SDRAMs and is sent at the leading edge of the data
window. DQS signals are complements, and timing is relative to the crosspoint of respective
DQS and DQS If the module is to be operated in single ended strobe mode, all DQS signals
must be tied on the system board to VSS and DDR2 SDRAM mode registers programmed appropriately.
VDD,VDD
SPD,VSS
Supply
Power supplies for core, I/O, Serial Presence Detect, and ground for the module.
SDA
In/Out
This is a bidirectional pin used to transfer data into or out of the SPD EEPROM. A resistor must be connected to VDD to act
as a pull up.
SCL
Input
This signal is used to clock data into and out of the SPD EEPROM. A resistor may be connected from SCL to VDD to act as
a pull up.
SA0~SA1
Input
Address pins used to select the Serial Presence Detect base address.
TEST
In/Out
The TEST pin is reserved for bus analysis tools and is not connected on normal memory modules(SO-DIMMs).
Rev. 1.5 Aug. 2005
256MB, 512MB, 1GB Unbuffered SODIMMs
DDR2 SDRAM
Functional Block Diagram: 512MB, 64Mx64 Module(Populated as 2 rank of x16 DDR2 SDRAMs)
M470T6554BG(Z)3/M470T6554BG(Z)0
3Ω + 5%
ODT1
ODT0
CKE1
CKE0
S1
S0
DQS0
DQS0
DM0
DQS1
DQS1
DM1
DQS2
DQS2
DM2
DQS3
DQS3
DM3
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
LDQS CS C
K
LDQS
E
LDM
I/O 0
I/O 1
D0
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
UDQS
UDQS
UDM
I/O 8
I/O 9
I/O 10
I/O 11
I/O 12
I/O 13
I/O 14
I/O 15
O
D
T
LDQS CS C
K
LDQS
E
LDM
I/O 0
I/O 1
D1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
UDQS
UDQS
UDM
I/O 8
I/O 9
I/O 10
I/O 11
I/O 12
I/O 13
I/O 14
I/O 15
O
D
T
LDQS CS C
K
LDQS
E
LDM
I/O 0
I/O 1
D4
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
UDQS
UDQS
UDM
I/O 8
I/O 9
I/O 10
I/O 11
I/O 12
I/O 13
I/O 14
I/O 15
O
D
T
LDQS CS C
K
LDQS
E
LDM
I/O 0
I/O 1
D5
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
UDQS
UDQS
UDM
I/O 8
I/O 9
I/O 10
I/O 11
I/O 12
I/O 13
I/O 14
I/O 15
O
D
T
DQS4
DQS4
DM4
DQS5
DQS5
DM5
DQS6
DQS6
DM6
DQS7
DQS7
DM7
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
LDQS CS C
K
LDQS
E
LDM
I/O 0
I/O 1
D2
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
UDQS
UDQS
UDM
I/O 8
I/O 9
I/O 10
I/O 11
I/O 12
I/O 13
I/O 14
I/O 15
O
D
T
LDQS CS C
K
LDQS
E
LDM
I/O 0
I/O 1
D6
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
UDQS
UDQS
UDM
I/O 8
I/O 9
I/O 10
I/O 11
I/O 12
I/O 13
I/O 14
I/O 15
O
D
T
LDQS CS C
K
LDQS
E
LDM
I/O 0
I/O 1
D3
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
UDQS
UDQS
UDM
I/O 8
I/O 9
I/O 10
I/O 11
I/O 12
I/O 13
I/O 14
I/O 15
O
D
T
LDQS CS C
K
LDQS
E
LDM
I/O 0
I/O 1
D7
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
UDQS
UDQS
UDM
I/O 8
I/O 9
I/O 10
I/O 11
I/O 12
I/O 13
I/O 14
I/O 15
O
D
T
3Ω + 5%
BA0 - BA1
DDR2 SDRAMs D0 - D7
A0 - A13
DDR2 SDRAMs D0 - D7
RAS
DDR2 SDRAMs D0 - D7
CAS
DDR2 SDRAMs D0 - D7
WE
DDR2 SDRAMs D0 - D7
SCL
SA0
SA1
SCL
A0
SPD
A1
A2
SDA
WP
* Clock Wiring
VDDSPD
Serial PD
VREF
DDR2 SDRAMs D0 - D7
VDD
DDR2 SDRAMs D0 - D7, VDD and VDDQ
VSS
DDR2 SDRAMs D0 - D7, SPD
Clock Input
DDR2 SDRAMs
*CK0/CK0
*CK1/CK1
4 DDR2 SDRAMs
4 DDR2 SDRAMs
* Wire per Clock Loading
Table/Wiring Diagrams
Notes :
1. DQ,DM, DQS/DQS resistors : 22 Ohms ± 5%.
2. BAx, Ax, RAS, CAS, WE resistors : 3.0 Ohms ± 5%.
Rev. 1.5 Aug. 2005
256MB, 512MB, 1GB Unbuffered SODIMMs
DDR2 SDRAM
Functional Block Diagram: 256MB, 32Mx64 Module(Populated as 1 rank of x16 DDR2 SDRAMs)
M470T3354BG(Z)3/M470T3354BG(Z)0
3Ω + 5%
CKE0
ODT0
S0
DQS0
DQS0
DM0
DQS1
DQS1
DM1
DQS2
DQS2
DM2
DQS3
DQS3
DM3
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
LDQS CS O
D
LDQS
T
LDM
I/O 0
I/O 1
D0
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
UDQS
UDQS
UDM
I/O 8
I/O 9
I/O 10
I/O 11
I/O 12
I/O 13
I/O 14
I/O 15
C
K
E
LDQS CS O
D
LDQS
T
LDM
I/O 0
I/O 1
D1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
UDQS
UDQS
UDM
I/O 8
I/O 9
I/O 10
I/O 11
I/O 12
I/O 13
I/O 14
I/O 15
C
K
E
3Ω
BA0 - BA1
DDR2 SDRAMs D0 - D3
A0 - A13
DDR2 SDRAMs D0 - D3
RAS
DDR2 SDRAMs D0 - D3
CAS
DDR2 SDRAMs D0 - D3
WE
DDR2 SDRAMs D0 - D3
DQS4
DQS4
DM4
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
DQS5
DQS5
DM5
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
DQS6
DQS6
DM6
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
DQS7
DQS7
DM7
SCL
SA0
SA1
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
SCL
A0
SPD
A1
A2
LDQS CS O
D
LDQS
T
LDM
I/O 0
I/O 1
D2
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
UDQS
UDQS
UDM
I/O 8
I/O 9
I/O 10
I/O 11
I/O 12
I/O 13
I/O 14
I/O 15
C
K
E
LDQS CS O
D
LDQS
T
LDM
I/O 0
I/O 1
D3
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
UDQS
UDQS
UDM
I/O 8
I/O 9
I/O 10
I/O 11
I/O 12
I/O 13
I/O 14
I/O 15
C
K
E
SDA
WP
* Clock Wiring
VDDSPD
Serial PD
Clock Input
DDR2 SDRAMs
VREF
DDR2 SDRAMs D0 - D3
*CK0/CK0
*CK1/CK1
2 DDR2 SDRAMs
2 DDR2 SDRAMs
VDD
DDR2 SDRAMs D0 - D3, VDD and VDDQ
VSS
DDR2 SDRAMs D0 - D3, SPD
* Wire per Clock Loading
Table/Wiring Diagrams
Notes :
1. DQ,DM, DQS/DQS resistors : 22 Ohms ± 5%.
2. BAx, Ax, RAS, CAS, WE resistors : 3.0 Ohms ± 5%.
Rev. 1.5 Aug. 2005
256MB, 512MB, 1GB Unbuffered SODIMMs
DDR2 SDRAM
Functional Block Diagram: 1GB, 128Mx64 Module(Populated as 2 ranks of x8 DDR2 SDRAMs)
M470T2953BS(Y)3/M470T2953BS(Y)0
3Ω + 5%
CKE1
ODT1
S1
CKE0
ODT0
S0
DQS0
DQS0
DM0
DQS1
DQS1
DM1
DQS2
DQS2
DM2
DQS3
DQS3
DM3
CS0 O
D
T
0
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQS
DQS
DM
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
CS0 O
DQS
DQS
D
DM
T
0
I/O 8
I/O 9
D1
I/O 10
I/O 11
I/O 12
I/O 13
I/O 14
I/O 15
C
K
E
0
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
DQS
DQS
DM
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
C
K
E
0
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
CS0 O
DQS
D
DQS
T
DM
0
I/O 8
I/O 9
D3
I/O 10
I/O 11
I/O 12
I/O 13
I/O 14
I/O 15
C
K
E
0
D0
CS0 O
D
T
0
D2
C
K
E
0
DQS
DQS
DM
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
CS1 O
D
T
1
D8
CS1 O
DQS
DQS
D
DM
T
1
I/O 8
I/O 9
D9
I/O 10
I/O 11
I/O 12
I/O 13
I/O 14
I/O 15
C
K
E
1
CS1 O
D
T
1
C
K
E
1
DQS
DQS
DM
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
DQS4
DQS4
DM4
C
K
E
1
DQS5
DQS5
DM5
DQS6
DQS6
DM6
D10
CS1 O
DQS
D
DQS
T
DM
1
I/O 8
I/O 9
D11
I/O 10
I/O 11
I/O 12
I/O 13
I/O 14
I/O 15
DQS7
DQS7
DM7
C
K
E
1
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
DQS
DQS
DM
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
CS0 O
D
T
0
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
DQS
DQS
DM
I/O 8
I/O 9
I/O 10
I/O 11
I/O 12
I/O 13
I/O 14
I/O 15
CS0 O
D
T
0
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
DQS
DQS
DM
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
CS0 O
D
T
0
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
DQS
DQS
DM
I/O 8
I/O 9
I/O 10
I/O 11
I/O 12
I/O 13
I/O 14
I/O 15
CS0 O
D
T
0
C
K
E
0
D4
C
K
E
0
D5
C
K
E
0
D6
C
K
E
0
D7
DQS
DQS
DM
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
CS1 O
D
T
1
DQS
DQS
DM
I/O 8
I/O 9
I/O 10
I/O 11
I/O 12
I/O 13
I/O 14
I/O 15
CS1 O
D
T
1
DQS
DQS
DM
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
CS1 O
D
T
1
DQS
DQS
DM
I/O 8
I/O 9
I/O 10
I/O 11
I/O 12
I/O 13
I/O 14
I/O 15
CS1 O
D
T
1
C
K
E
1
D12
C
K
E
1
D13
C
K
E
1
D14
C
K
E
1
D15
* Clock Wiring
10Ω + 5%
BA0 - BA1
DDR2 SDRAMs D0 - D15
A0 - A13
DDR2 SDRAMs D0 - D15
RAS
DDR2 SDRAMs D0 - D15
CAS
DDR2 SDRAMs D0 - D15
WE
DDR2 SDRAMs D0 - D15
SCL
SA0
SA1
VDDSPD
Serial PD
VREF
DDR2 SDRAMs D0 - D15
VDD
DDR2 SDRAMs D0 - D15, VDD and VDDQ
VSS
DDR2 SDRAMs D0 - D15, SPD
SCL
A0
SPD
A1
A2
WP
SDA
Clock Input
DDR2 SDRAMs
*CK0/CK0
*CK1/CK1
8 DDR2 SDRAMs
8 DDR2 SDRAMs
* Wire per Clock Loading
Table/Wiring Diagrams
Notes :
1. DQ,DM, DQS/DQS resistors : 22 Ohms ± 5%.
2. BAx, Ax, RAS, CAS, WE resistors : 10 Ohms ± 5%.
Rev. 1.5 Aug. 2005
256MB, 512MB, 1GB Unbuffered SODIMMs
DDR2 SDRAM
Absolute Maximum DC Ratings
Symbol
Rating
Units
Notes
Voltage on VDD pin relative to VSS
- 1.0 V ~ 2.3 V
V
1
VDDQ
Voltage on VDDQ pin relative to VSS
- 0.5 V ~ 2.3 V
V
1
VDDL
Voltage on VDDL pin relative to VSS
- 0.5 V ~ 2.3 V
V
1
Voltage on any pin relative to VSS
- 0.5 V ~ 2.3 V
V
1
-55 to +100
°C
1, 2
VDD
VIN, VOUT
TSTG
Parameter
Storage Temperature
Note :
1. Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Exposure to absolute maximum rating conditions for extended periods may affect reliability.
2. Storage Temperature is the case surface temperature on the center/top side of the DRAM. For the measurement conditions, please refer to JESD51-2
standard.
AC & DC Operating Conditions
Recommended DC Operating Conditions (SSTL - 1.8)
Symbol
Parameter
Rating
Min.
Typ.
Max.
1.7
1.8
1.9
Units
Notes
VDD
Supply Voltage
VDDL
Supply Voltage for DLL
1.7
1.8
1.9
V
4
VDDQ
Supply Voltage for Output
1.7
1.8
1.9
V
4
VREF
Input Reference Voltage
0.49*VDDQ
0.50*VDDQ
0.51*VDDQ
mV
1,2
Termination Voltage
VREF-0.04
VREF
VREF+0.04
V
3
VTT
V
Note : There is no specific device VDD supply voltage requirement for SSTL-1.8 compliance. However under all conditions VDDQ must be less than or equal
to VDD.
1. The value of VREF may be selected by the user to provide optimum noise margin in the system. Typically the value of VREF is expected to be about 0.5
x VDDQ of the transmitting device and VREF is expected to track variations in VDDQ.
2. Peak to peak AC noise on VREF may not exceed +/-2% VREF(DC).
3. VTT of transmitting device must track VREF of receiving device.
4. AC parameters are measured with VDD, VDDQ and VDDL tied together.
Rev. 1.5 Aug. 2005
256MB, 512MB, 1GB Unbuffered SODIMMs
DDR2 SDRAM
Operating Temperature Condition
Symbol
Parameter
Rating
Units
Notes
TOPER
Operating Temperature
0 to 95
°C
1, 2, 3
Note :
1. Operating Temperature is the case surface temperature on the center/top side of the DRAM. For the measurement conditions, please refer to JESD51.2
standard.
2. At 0 - 85 °C, operation temperature range are the temperature which all DRAM specification will be supported.
3. At 85 - 95 °C operation temperature range, doubling refresh commands in frequency to a 32ms period ( tREFI=3.9 us ) is required, and to enter to self
refresh mode at this temperature range, an EMRS command is required to change internal refresh rate.
Input DC Logic Level
Symbol
Parameter
Min.
Max.
Units
VIH(DC)
DC input logic high
VREF + 0.125
VDDQ + 0.3
V
VIL(DC)
DC input logic low
- 0.3
VREF - 0.125
V
Max.
Units
Notes
Input AC Logic Level
Symbol
Parameter
Min.
VIH(AC)
AC input logic high
VREF + 0.250
-
V
VIL(AC)
AC input logic low
-
VREF - 0.250
V
Notes
AC Input Test Conditions
Symbol
VREF
VSWING(MAX)
SLEW
Condition
Input reference voltage
Value
Units
Notes
0.5 * VDDQ
V
1
Input signal maximum peak to peak swing
1.0
V
1
Input signal minimum slew rate
1.0
V/ns
2, 3
Notes:
1. Input waveform timing is referenced to the input signal crossing through the VIH/IL(AC) level applied to the device under test.
2. The input signal minimum slew rate is to be maintained over the range from VREF to VIH(AC) min for rising edges and the range from VREF to VIL(AC)
max for falling edges as shown in the below figure.
3. AC timings are referenced with input waveforms switching from VIL(AC) to VIH(AC) on the positive transitions and VIH(AC) to VIL(AC) on the negative
transitions.
VDDQ
VIH(AC) min
VIH(DC) min
VSWING(MAX)
VREF
VIL(DC) max
VIL(AC) max
delta TF
Falling Slew =
delta TR
VREF - VIL(AC) max
delta TF
Rising Slew =
VSS
VIH(AC) min - VREF
delta TR
< AC Input Test Signal Waveform >
Rev. 1.5 Aug. 2005
256MB, 512MB, 1GB Unbuffered SODIMMs
DDR2 SDRAM
IDD Specification Parameters Definition
(IDD values are for full operating range of Voltage and Temperature)
Symbol
Proposed Conditions
Units
IDD0
Operating one bank active-precharge current;
tCK = tCK(IDD), tRC = tRC(IDD), tRAS = tRASmin(IDD); CKE is HIGH, CS\ is HIGH between valid commands;
Address bus inputs are SWITCHING; Data bus inputs are SWITCHING
mA
IDD1
Operating one bank active-read-precharge current;
IOUT = 0mA; BL = 4, CL = CL(IDD), AL = 0; tCK = tCK(IDD), tRC = tRC (IDD), tRAS = tRASmin(IDD), tRCD =
tRCD(IDD); CKE is HIGH, CS\ is HIGH between valid commands; Address bus inputs are SWITCHING; Data pattern
is same as IDD4W
mA
IDD2P
Precharge power-down current;
All banks idle; tCK = tCK(IDD); CKE is LOW; Other control and address bus inputs are STABLE; Data bus inputs are
FLOATING
mA
IDD2Q
Precharge quiet standby current;
All banks idle; tCK = tCK(IDD); CKE is HIGH, CS\ is HIGH; Other control and address bus inputs are STABLE; Data
bus inputs are FLOATING
mA
IDD2N
Precharge standby current;
All banks idle; tCK = tCK(IDD); CKE is HIGH, CS\ is HIGH; Other control and address bus inputs are SWITCHING;
Data bus inputs are SWITCHING
mA
IDD3P
Active power-down current;
All banks open; tCK = tCK(IDD); CKE is LOW; Other control and address bus
inputs are STABLE; Data bus inputs are FLOATING
Fast PDN Exit MRS(12) = 0mA
mA
Slow PDN Exit MRS(12) = 1mA
mA
IDD3N
Active standby current;
All banks open; tCK = tCK(IDD), tRAS = tRASmax(IDD), tRP = tRP(IDD); CKE is HIGH, CS\ is HIGH between valid
commands; Other control and address bus inputs are SWITCHING; Data bus inputs are SWITCHING
mA
IDD4W
Operating burst write current;
All banks open, Continuous burst writes; BL = 4, CL = CL(IDD), AL = 0; tCK = tCK(IDD), tRAS = tRASmax(IDD), tRP
= tRP(IDD); CKE is HIGH, CS\ is HIGH between valid commands; Address bus inputs are SWITCHING; Data bus
inputs are SWITCHING
mA
IDD4R
Operating burst read current;
All banks open, Continuous burst reads, IOUT = 0mA; BL = 4, CL = CL(IDD), AL = 0; tCK = tCK(IDD), tRAS = tRASmax(IDD), tRP = tRP(IDD); CKE is HIGH, CS\ is HIGH between valid commands; Address bus inputs are SWITCHING; Data pattern is same as IDD4W
mA
IDD5B
Burst auto refresh current;
tCK = tCK(IDD); Refresh command at every tRFC(IDD) interval; CKE is HIGH, CS\ is HIGH between valid commands;
Other control and address bus inputs are SWITCHING; Data bus inputs are SWITCHING
mA
IDD6
Self refresh current;
CK and CK\ at 0V; CKE ≤ 0.2V; Other control and address bus inputs are
FLOATING; Data bus inputs are FLOATING
IDD7
Operating bank interleave read current;
All bank interleaving reads, IOUT = 0mA; BL = 4, CL = CL(IDD), AL = tRCD(IDD)-1*tCK(IDD); tCK = tCK(IDD), tRC =
tRC(IDD), tRRD = tRRD(IDD), tFAW = tFAW(IDD), tRCD = 1*tCK(IDD); CKE is HIGH, CS\ is HIGH between valid
commands; Address bus inputs are STABLE during DESELECTs; Data pattern is same as IDD4R; Refer to the following page for detailed timing conditions
Normal
mA
Low Power
mA
Notes
mA
Rev. 1.5 Aug. 2005
256MB, 512MB, 1GB Unbuffered SODIMMs
DDR2 SDRAM
Operating Current Table(1-1) (TA=0oC, VDD= 1.9V)
M470T6554BG(Z)3/M470T6554BG(Z)0 : 64Mx64 512MB Module
Symbol
CD5
(DDR533@CL=4)
LD5
(DDR533@CL=4)
CCC
(DDR400@CL=3)
LCC
(DDR400@CL=3)
Unit
IDD0
760
460
720
460
mA
IDD1
860
560
760
520
mA
IDD2P
64
64
64
64
mA
IDD2Q
200
200
200
200
mA
mA
IDD2N
240
200
240
200
IDD3P-F
240
120
240
120
mA
IDD3P-S
120
120
120
120
mA
IDD3N
560
260
520
260
mA
IDD4W
1,200
700
1,000
700
mA
IDD4R
1,100
700
940
700
mA
IDD5B
1,060
860
1,000
860
mA
IDD6
44
40
44
40
mA
IDD7
1,840
1,060
1,760
1,060
mA
Notes
* Module IDD was calculated on the basis of component IDD and can be differently measured according to DQ loading cap.
M470T3354BG(Z)3/M470T3354BG(Z)0 : 32Mx64 256MB Module
Symbol
CD5
(DDR533@CL=4)
LD5
(DDR533@CL=4)
CCC
(DDR400@CL=3)
LCC
(DDR400@CL=3)
Unit
IDD0
480
360
460
360
mA
mA
IDD1
580
460
500
420
IDD2P
32
32
32
32
mA
IDD2Q
100
100
100
100
mA
IDD2N
120
100
120
100
mA
IDD3P-F
120
60
120
60
mA
IDD3P-S
60
60
60
60
mA
IDD3N
280
160
260
160
mA
IDD4W
920
600
740
520
mA
IDD4R
820
600
680
520
mA
IDD5B
780
760
740
760
mA
IDD6
22
20
22
20
mA
IDD7
1,560
960
1,500
960
mA
Notes
* Module IDD was calculated on the basis of component IDD and can be differently measured according to DQ loading cap.
Rev. 1.5 Aug. 2005
256MB, 512MB, 1GB Unbuffered SODIMMs
DDR2 SDRAM
Operating Current Table(1-2) (TA=0oC, VDD= 1.9V)
M470T2953BS(Y)3/M470T2953BS(Y)0 : 128Mx64 1GB Module
Symbol
CD5
(DDR533@CL=4)
LD5
(DDR533@CL=4)
CCC
(DDR400@CL=3)
LCC
(DDR400@CL=3)
Unit
IDD0
1,360
760
1,280
760
mA
IDD1
1,440
920
1,320
840
mA
IDD2P
128
128
128
128
mA
IDD2Q
400
400
400
400
mA
IDD2N
480
400
480
400
mA
IDD3P-F
480
240
480
240
mA
IDD3P-S
240
240
240
240
mA
IDD3N
1,120
520
1,040
520
mA
IDD4W
2,160
1,160
1,680
1,000
mA
IDD4R
2,000
1,160
1,680
1,000
mA
IDD5B
2,120
1,720
2,000
1,720
mA
IDD6
88
80
88
80
mA
IDD7
2,760
1,960
2,680
1,960
mA
Notes
* Module IDD was calculated on the basis of component IDD and can be differently measured according to DQ loading cap.
Input/Output Capacitance(VDD=1.8V, VDDQ=1.8V, TA=25oC)
Parameter
Non-ECC
Min
Symbol
Input capacitance, CK and CK
Input capacitance, CKE , CS, Addr, RAS, CAS, WE
Input/output capacitance, DQ, DM, DQS, DQS
Max
M470T6554BG(Z)3
M470T6554BG(Z)0
Min
Max
M470T3354BG(Z)3
M470T3354BG(Z)0
Min
Max
M470T2953BS(Y)3
M470T2953BS(Y)0
CCK
-
32
-
24
-
48
CI
-
34
-
34
-
42
CIO
-
10
-
6
-
10
Units
pF
* DM is internally loaded to match DQ and DQS identically.
Rev. 1.5 Aug. 2005
256MB, 512MB, 1GB Unbuffered SODIMMs
DDR2 SDRAM
Electrical Characteristics & AC Timing for DDR2-533/400 SDRAM
(0 °C < TCASE < 95 °C; VDDQ = 1.8V + 0.1V; VDD = 1.8V + 0.1V)
Refresh Parameters by Device Density
Parameter
Symbol
Refresh to active/Refresh command time
tRFC
Average periodic refresh interval
tREFI
256Mb
512Mb
1Gb
2Gb
4Gb
Units
75
105
127.5
195
tbd
ns
0 °C ≤ TCASE ≤ 85°C
7.8
7.8
7.8
7.8
7.8
µs
85 °C < TCASE ≤ 95°C
3.9
3.9
3.9
3.9
3.9
µs
Speed Bins and CL, tRCD, tRP, tRC and tRAS for Corresponding Bin
Speed
DDR2-533(D5)
Bin (CL - tRCD - tRP)
Parameter
DDR2-400(CC)
4-4-4
3-3-3
Units
min
max
min
max
tCK, CL=3
5
8
5
8
ns
tCK, CL=4
3.75
8
5
8
ns
-
-
-
-
ns
tCK, CL=5
tRCD
15
15
ns
tRP
15
15
ns
tRC
55
55
ns
tRAS
40
70000
40
70000
ns
Rev. 1.5 Aug. 2005
256MB, 512MB, 1GB Unbuffered SODIMMs
DDR2 SDRAM
Timing Parameters by Speed Grade
(Refer to notes for informations related to this table at the bottom)
Parameter
Symbol
DDR2-533
DDR2-400
min
max
min
max
Units
DQ output access time from CK/CK
tAC
-500
+500
-600
+600
ps
DQS output access time from CK/CK
tDQSCK
-450
+450
-500
+500
ps
CK high-level width
tCH
0.45
0.55
0.45
0.55
tCK
CK low-level width
tCL
0.45
0.55
0.45
0.55
tCK
CK half period
tHP
min(tCL,
tCH)
x
min(tCL,
tCH)
x
ps
Clock cycle time, CL=x
tCK
3750
8000
5000
8000
ps
DQ and DM input hold time
tDH
225
x
275
x
ps
DQ and DM input setup time
tDS
100
x
150
x
ps
Control & Address input pulse width for each input
tIPW
0.6
x
0.6
x
tCK
DQ and DM input pulse width for each input
tDIPW
0.35
x
0.35
x
tCK
Data-out high-impedance time from CK/CK
tHZ
DQS low-impedance time from CK/CK
tLZ(DQS)
DQ low-impedance time from CK/CK
x
tAC max
x
tAC max
ps
tAC min
tAC max
tAC min
tAC max
ps
tLZ(DQ)
2* tACmin
tAC max
2* tACmin
tAC max
ps
DQS-DQ skew for DQS and associated DQ signals
tDQSQ
x
300
x
350
ps
DQ hold skew factor
tQHS
x
400
x
450
ps
DQ/DQS output hold time from DQS
tQH
tHP - tQHS
x
tHP - tQHS
x
ps
Write command to first DQS latching transition
tDQSS
WL-0.25
WL+0.25
WL-0.25
WL+0.25
tCK
DQS input high pulse width
tDQSH
0.35
x
0.35
x
tCK
DQS input low pulse width
tDQSL
0.35
x
0.35
x
tCK
DQS falling edge to CK setup time
tDSS
0.2
x
0.2
x
tCK
DQS falling edge hold time from CK
tDSH
0.2
x
0.2
x
tCK
Mode register set command cycle time
tMRD
2
x
2
x
tCK
Write postamble
tWPST
0.4
0.6
0.4
0.6
tCK
Write preamble
tWPRE
0.35
x
0.35
x
tCK
Address and control input hold time
tIH
375
x
475
x
ps
Address and control input setup time
tIS
250
x
350
x
ps
Read preamble
tRPRE
0.9
1.1
0.9
1.1
tCK
Read postamble
tRPST
0.4
0.6
0.4
0.6
tCK
Active to active command period for 1KB page size products tRRD
7.5
x
7.5
x
ns
Active to active command period for 2KB page size products tRRD
10
x
10
x
ns
Four Activate Window for 1KB page size products
tFAW
37.5
37.5
Four Activate Window for 2KB page size products
tFAW
50
50
ns
CAS to CAS command delay
tCCD
2
2
tCK
Write recovery time
tWR
15
x
15
x
ns
Auto precharge write recovery + precharge time
tDAL
tWR+tRP
x
tWR+tRP
x
tCK
Internal write to read command delay
tWTR
7.5
x
10
x
ns
Internal read to precharge command delay
tRTP
7.5
7.5
Exit self refresh to a non-read command
tXSNR
tRFC + 10
tRFC + 10
ns
Exit self refresh to a read command
tXSRD
200
200
tCK
Exit precharge power down to any non-read command
tXP
2
x
2
x
tCK
Exit active power down to read command
tXARD
2
x
2
x
tCK
Exit active power down to read command (Slow exit, Lower
power)
tXARDS
6 - AL
6 - AL
Notes
ns
ns
tCK
Rev. 1.5 Aug. 2005
256MB, 512MB, 1GB Unbuffered SODIMMs
Parameter
Symbol
CKE minimum pulse width (high and low pulse width)
tCKE
ODT turn-on delay
tAOND
ODT turn-on
tAON
ODT turn-on(Power-Down mode)
tAONPD
ODT turn-off delay
tAOFD
DDR2 SDRAM
DDR2-533
min
DDR2-400
max
3
min
max
3
Units
tCK
2
2
2
2
tCK
tAC(min)
tAC(max)+1
tAC(min)
tAC(max)+1
ns
tAC(min)+2
2tCK+tAC(
max)+1
tAC(min)+2
2tCK+tAC
(max)+1
ns
2.5
2.5
2.5
2.5
tCK
tAC(min)
tAC(max)+
0.6
tAC(min)
tAC(max)+
0.6
ns
2.5tCK+
tAC(max)+1
ns
ODT turn-off
tAOF
ODT turn-off (Power-Down mode)
tAOFPD
ODT to power down entry latency
tANPD
3
3
tCK
ODT power down exit latency
tAXPD
8
8
tCK
OCD drive mode output delay
tOIT
0
Minimum time clocks remains ON after CKE asynchronously
tDelay
drops LOW
tAC(min)+2
tIS+tCK +tIH
2.5tCK+
tAC(min)+2
tAC(max)+1
12
0
tIS+tCK +tIH
Notes
12
ns
ns
Rev. 1.5 Aug. 2005
256MB, 512MB, 1GB Unbuffered SODIMMs
DDR2 SDRAM
Physical Dimensions: 32Mbx16 based 64Mx64 Module(2 Rank)
M470T6554BG(Z)3/M470T6554BG(Z)0
67.60 mm
3.8 mm
Max
a
1
b
11.40
199
30.00
20.00
4.00 ± 0.10
6.00
2.00
1.1 mm
Max
47.40
16.25
63.00
2
200
30.00
SPD
a
67.60 mm
DETAIL a
BACK SIDE
FRONT SIDE
4.00 ± 0.10
1.0 ± 0.05
1.0 ± 0.05
2.55
1.50 ± 0.10
1.80 ± 0.10
4.00 ± 0.10
0.20 ± 0.15
4.20
2.70 ± 0.10
DETAIL b
2.40 ± 0.10
4.20
0.60
0.45 ± 0.03
The used device is 32M x16 DDR2 SDRAM, FBGA.
DDR2 SDRAM Part NO : K4T51163QB
Rev. 1.5 Aug. 2005
256MB, 512MB, 1GB Unbuffered SODIMMs
DDR2 SDRAM
Physical Dimensions: 32Mbx16 based 32Mx64 Module(1 Rank)
M470T3354BG(Z)3/M470T3354BG(Z)0
67.60 mm
2.45 mm
Max
a
1
b
11.40
199
30.00
20.00
4.00 ± 0.10
6.00
SPD
2.00
47.40
1.1 mm
Max
16.25
63.00
2
200
30.00
a
67.60 mm
DETAIL a
BACK SIDE
FRONT SIDE
4.00 ± 0.10
1.0 ± 0.05
1.0 ± 0.05
2.55
1.50 ± 0.10
1.80 ± 0.10
4.00 ± 0.10
0.20 ± 0.15
4.20
2.70 ± 0.10
DETAIL b
2.40 ± 0.10
4.20
0.60
0.45 ± 0.03
The used device is 32M x16 DDR2 SDRAM, FBGA.
DDR2 SDRAM Part NO : K4T51163QB
Rev. 1.5 Aug. 2005
256MB, 512MB, 1GB Unbuffered SODIMMs
DDR2 SDRAM
Physical Dimensions: 64Mbx8 based 128Mx64 Module(2 Ranks)
M470T2953BS(Y)3/M470T2953BS(Y)0
67.60 mm
3.8 mm
max
2.00
a
1
b
11.40
199
30.00
20.00
4.00 ± 0.10
6.00
SPD
47.40
16.25
1.1mm
max
63.00
2
200
30.00
a
67.60 mm
DETAIL a
BACK SIDE
FRONT SIDE
4.00 ± 0.10
1.0 ± 0.05
1.0 ± 0.05
2.55
1.50 ± 0.10
1.80 ± 0.10
4.00 ± 0.10
0.20 ± 0.15
4.20
2.70 ± 0.10
DETAIL b
2.40 ± 0.10
4.20
0.60
0.45 ± 0.03
The used device is 64M x8 DDR2 SDRAM, FBGA.
DDR2 SDRAM Part NO : K4T51083QB
Rev. 1.5 Aug. 2005
256MB, 512MB, 1GB Unbuffered SODIMMs
DDR2 SDRAM
Revision History
Revision 1.0 (Jan. 2004)
- Initial Release
Revision 1.1 (Jun. 2004)
- Added lead-free part number in the ordering information
- Changed IDD2P
Revision 1.2 (Jul. 2004)
- Added current values and part number of low power product
Revision 1.3 (Feb. 2005)
- Added the detail information for mechanical dimension
Revision 1.4 (Mar. 2005)
- Changed 1GB Functional Block Diagram
Revision 1.5 (Aug. 2005)
- Changed the IDD Specification Parameters Definition
Rev. 1.5 Aug. 2005
Similar pages