STMicroelectronics M54HCT139F1R Dual 2 to 4 decoder/demultiplexer Datasheet

M54HCT139
M74HCT139
DUAL 2 TO 4 DECODER/DEMULTIPLEXER
.
.
.
.
.
.
.
HIGH SPEED
tPD = 17 ns (TYP.) AT VCC = 5 V
LOW POWER DISSIPATION
ICC = 4 µA (MAX.) AT TA = 25 °C
COMPATIBLE WITH TTL OUTPUTS
VIH = 2V (MIN.) VIL = 0.8V (MAX)
OUTPUT DRIVE CAPABILITY
10 LSTTL LOADS
SYMMETRICAL OUTPUT IMPEDANCE
|IOH| = IOL = 4 mA (MIN.)
BALANCED PROPAGATION DELAYS
tPLH = tPHL
PIN AND FUNCTION COMPATIBLE
WITH 54/74LS139
DESCRIPTION
The M54/74HCT139 is a high speed CMOS DUAL
TWO LINE TO FOUR LINE DECODER/DEMULTIPLEXER fabricated in silicon gate C2MOS technology. It has the same high speed performance of
LSTTL combined with true CMOS low power consumption. The active low enable input can be used for
gating or as a data input for demultiplexing applications. While the enable input is held high, all four outputs are high independently of the other inputs. All
inputs are equipped with protection circuits against
static discharge and transient excess volt-age.This integrated circuit has input and output characteristics
that are fully compatible with 54/74 LSTTL logic
families. M54/74HCT devices are designed to directly
interface HSC2MOS systems with TTL and NMOS
components. They are also plug in replacements for
B1R
(Plastic Package)
F1R
(Ceramic Package)
M1R
(Micro Package)
C1R
(Chip Carrier)
ORDER CODES :
M54HCT139F1R
M74HCT139M1R
M74HCT139B1R
M74HCT139C1R
PIN CONNECTIONS (top view)
INPUT AND OUTPUT EQUIVALENT CIRCUIT
NC =
No Internal
Connection
February 1993
1/9
M54/M74HCT139
TRUTH TABLE
INPUTS
ENABLE SELECT
G
B
A
H
X
X
L
L
L
L
L
H
L
H
L
L
H
H
IEC LOGIC SYMBOLS
OUTPUTS
Y0
Y1
Y2
Y3
SELECTED
OUTPUT
H
L
H
H
H
H
H
L
H
H
H
H
H
L
H
H
H
H
H
L
NONE
Y0
Y1
Y2
Y3
PIN DESCRIPTION
PIN No
1, 15
2, 3
4, 5, 6, 7
12, 11, 10, 9
14, 13
8
16
SYMBOL
1G, 2G
1A, 1B
1Y0 to 1Y3
2Y0 to 2Y3
2A, 2B
GND
VCC
NAME AND FUNCTION
Enable Inputs
Address Inputs
Outputs
Outputs
Address Inputs
Ground (0V)
Positive Supply Voltage
SCHEMATIC CIRCUIT
ABSOLUTE MAXIMUM RATINGS
Symbol
ICC
Value
Unit
VCC
VI
Supply Voltage
DC Input Voltage
Parameter
-0.5 to +7
-0.5 to VCC + 0.5
V
V
VO
DC Output Voltage
-0.5 to VCC + 0.5
V
IIK
DC Input Diode Current
± 20
mA
IOK
DC Output Diode Current
± 20
mA
IO
or IGND
DC Output Source Sink Current Per Output Pin
DC VCC or Ground Current
± 25
± 50
mA
mA
PD
Power Dissipation
500 (*)
mW
Tstg
TL
Storage Temperature
Lead Temperature (10 sec)
-65 to +150
300
o
o
C
C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition isnotimplied.
(*) 500 mW: ≅ 65 oC derate to 300 mW by 10mW/oC: 65 oC to 85 oC
2/9
M54/M74HCT139
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
Value
Unit
V
V
VCC
VI
Supply Voltage
Input Voltage
4.5 to 5.5
0 to VCC
VO
Output Voltage
0 to VCC
Top
tr, tf
Operating Temperature: M54HC Series
M74HC Series
Input Rise and Fall Time (VCC = 4.5 to 5.5V)
V
o
-55 to +125
-40 to +85
0 to 500
C
C
ns
o
DC SPECIFICATIONS
Test Conditions
Symbol
Parameter
VIH
High Level Input
Voltage
V IL
Low Level Input
Voltage
V OH
High Level
Output Voltage
VOL
II
ICC
∆ICC
Low Level Output
Voltage
Input Leakage
Current
Quiescent Supply
Current
Additional worst
case supply
current
Value
TA = 25 oC
54HC and 74HC
VCC
(V)
Min.
2.0
4.5
to
5.5
4.5
to
5.5
Typ.
Max.
-40 to 85 oC -55 to 125 oC
74HC
54HC
Min.
2.0
0.8
4.5
VI = IO=-20 µA
VIH
or IO=-4.0 mA
V IL
4.5
VI = IO= 20 µA
VIH
or IO= 4.0 mA
V IL
Max.
Min.
2.0
0.8
Max.
V
0.8
4.4
4.5
4.4
4.4
4.18
4.31
4.13
4.10
Unit
V
V
0.0
0.1
0.1
0.1
0.17
0.26
0.33
0.4
VI = VCC or GND
±0.1
±1
±1
µA
5.5
VI = VCC or GND
4
40
80
µA
5.5
Per Input pin
VI = 0.5V or
V I = 2.4V
Other Inputs at
V CC or GND
IO= 0
2.0
2.9
3.0
mA
5.5
V
3/9
M54/M74HCT139
AC ELECTRICAL CHARACTERISTICS (C L = 50 pF, Input t r = tf = 6 ns)
Test Conditions
Value
o
-40 to 85 oC -55 to 125 oC
74HC
54HC
Min. Max. Min. Max.
Symbol
Parameter
VCC
(V)
TA = 25 C
54HC and 74HC
Min. Typ. Max.
tTLH
tTHL
Output Transition
Time
4.5
8
15
19
22
ns
tPLH
tPHL
Propagation
Delay Time
(A, B - Y)
4.5
19
30
38
45
ns
tPLH
tPHL
Propagation
Delay Time
(G - Y)
4.5
17
27
34
41
ns
10
10
10
CIN
Input Capacitance
5
CPD (*)
Power Dissipation
Capacitance
40
Unit
pF
pF
(*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load.
(Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD •VCC •fIN + ICC/2 (per decoder)
SWITCHING CHARACTERISTICS TEST CIRCUIT
TEST CIRCUIT ICC (Opr.)
INPUT WAVEFORM IS THE SAME AS THAT IN CASE OF
SWITCHING CHARACTERISTICSTEST.
4/9
M54/M74HCT139
Plastic DIP16 (0.25) MECHANICAL DATA
mm
DIM.
MIN.
a1
0.51
B
0.77
TYP.
inch
MAX.
MIN.
TYP.
MAX.
0.020
1.65
0.030
0.065
b
0.5
0.020
b1
0.25
0.010
D
20
0.787
E
8.5
0.335
e
2.54
0.100
e3
17.78
0.700
F
7.1
0.280
I
5.1
0.201
L
Z
3.3
0.130
1.27
0.050
P001C
5/9
M54/M74HCT139
Ceramic DIP16/1 MECHANICAL DATA
mm
DIM.
MIN.
TYP.
inch
MAX.
MIN.
TYP.
MAX.
A
20
0.787
B
7
0.276
D
E
3.3
0.130
0.38
e3
0.015
17.78
0.700
F
2.29
2.79
0.090
0.110
G
0.4
0.55
0.016
0.022
H
1.17
1.52
0.046
0.060
L
0.22
0.31
0.009
0.012
M
0.51
1.27
0.020
0.050
N
P
Q
10.3
7.8
8.05
5.08
0.406
0.307
0.317
0.200
P053D
6/9
M54/M74HCT139
SO16 (Narrow) MECHANICAL DATA
mm
DIM.
MIN.
TYP.
A
a1
inch
MAX.
MIN.
TYP.
1.75
0.1
0.068
0.2
a2
MAX.
0.004
0.007
1.65
0.064
b
0.35
0.46
0.013
0.018
b1
0.19
0.25
0.007
0.010
C
0.5
0.019
c1
45° (typ.)
D
9.8
E
5.8
10
0.385
6.2
0.228
0.393
0.244
e
1.27
0.050
e3
8.89
0.350
F
3.8
4.0
0.149
0.157
G
4.6
5.3
0.181
0.208
L
0.5
1.27
0.019
0.050
M
S
0.62
0.024
8° (max.)
P013H
7/9
M54/M74HCT139
PLCC20 MECHANICAL DATA
mm
DIM.
MIN.
TYP.
inch
MAX.
MIN.
TYP.
MAX.
A
9.78
10.03
0.385
0.395
B
8.89
9.04
0.350
0.356
D
4.2
4.57
0.165
0.180
d1
2.54
0.100
d2
0.56
0.022
E
7.37
8.38
0.290
0.330
e
1.27
0.050
e3
5.08
0.200
F
0.38
0.015
G
0.101
0.004
M
1.27
0.050
M1
1.14
0.045
P027A
8/9
M54/M74HCT139
Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No
license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned
in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied.
SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express
written approval of SGS-THOMSON Microelectonics.
 1994 SGS-THOMSON Microelectronics - All Rights Reserved
SGS-THOMSON Microelectronics GROUP OF COMPANIES
Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A
9/9
Similar pages