STMicroelectronics M93C86M93C86-W 16-kbit, 8-kbit, 4-kbit, 2-kbit and 1-kbit (8-bit or 16-bit wide) microwire serial access eeprom Datasheet

M93C86xx M93C76xx
M93C66xx M93C56xx M93C46xx
16-Kbit, 8-Kbit, 4-Kbit, 2-Kbit and 1-Kbit
(8-bit or 16-bit wide) MICROWIRE serial access EEPROM
Datasheet - production data
• Self-timed programming cycle with auto-erase:
5 ms
• READY/BUSY signal during programming
• 2 MHz clock rate
• Sequential read operation
• Enhanced ESD/latch-up behavior
PDIP8 (BN)
• More than 1 million write cycles
• More than 40 year data retention
• Packages
– SO8, TSSOP8, UFDFPN8 packages:
RoHS-compliant and Halogen-free
(ECOPACK2®)
– PDIP8 package:
RoHS-compliant (ECOPACK1®)
SO8 (MN)
150 mil width
Table 1. Device summary
TSSOP8 (DW)
169 mil width
Reference
M93C46xx
Part
number
M93C46
M93C46-W
Memory
size
1 Kbit
M93C56
UFDFPN8 (MC)
2 x 3 mm
M93C56xx
M93C66xx
Features
M93C56-W
M93C76xx
• Single supply voltage:
– 4.5 V to 5.5 V for M93Cx6
– 2.5 V to 5.5 V for M93Cx6-W
– 1.8 V to 5.5 V for M93Cx6-R
M93C86xx
4.5 V to 5.5 V
2.5 V to 5.5 V
4.5 V to 5.5 V
2 Kbit
2.5 V to 5.5 V
M93C56-R
1.8 V to 5.5 V
M93C66
4.5 V to 5.5 V
M93C66-W
4 Kbit
M93C66-R
• Industry standard MICROWIRE bus
Supply
voltage
M93C76-W
M93C76-R
M93C86
M93C86-W
2.5 V to 5.5 V
1.8 V to 5.5 V
8 Kbit
16 Kbit
2.5 V to 5.5 V
1.8 V to 5.5 V
4.5 V to 5.5 V
2.5 V to 5.5 V
• Dual organization: by word (x16) or byte (x8)
• Programming instructions that work on: byte,
word or entire memory
April 2013
This is information on a product in full production.
DocID4997 Rev 13
1/33
www.st.com
1
Contents
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
Contents
1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2
Connecting to the serial bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3
Operating features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1
Supply voltage (VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1.1
Operating supply voltage (VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1.2
Power-up conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1.3
Power-up and device reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1.4
Power-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4
Memory organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5
Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.1
Read Data from Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.2
Erase and Write data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.2.1
Write Enable and Write Disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.2.2
Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.2.3
Write All . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.2.4
Erase Byte or Word . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.2.5
Erase All . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6
READY/BUSY status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7
Initial delivery state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
8
Clock pulse counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
9
Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
10
DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
11
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
12
Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2/33
DocID4997 Rev 13
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
13
Contents
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
DocID4997 Rev 13
3/33
List of tables
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Table 16.
Table 17.
Table 18.
Table 19.
Table 20.
Table 21.
Table 22.
Table 23.
Table 24.
Table 25.
4/33
Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Memory size versus organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Instruction set for the M93C46 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Instruction set for the M93C56 and M93C66 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Instruction set for the M93C76 and M93C86 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Operating conditions (M93Cx6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Operating conditions (M93Cx6-W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Operating conditions (M93Cx6-R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
AC measurement conditions (M93Cx6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
AC measurement conditions (M93Cx6-W and M93Cx6-R) . . . . . . . . . . . . . . . . . . . . . . . . 20
Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
DC characteristics (M93Cx6, device grade 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
DC characteristics (M93Cx6-W, device grade 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
DC characteristics (M93Cx6-R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
AC characteristics (M93Cx6, device grade 6). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
AC characteristics (M93Cx6-W, device grade 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
AC characteristics (M93Cx6-R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
PDIP8 – 8 lead plastic dual in-line package, 300 mils body width,
package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
SO8 narrow – 8 lead plastic small outline, 150 mils body width, package data . . . . . . . . . 28
UFDFPN8 8-lead ultra thin fine pitch dual flat package no lead
2 x 3 mm, data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
TSSOP8 – 8 lead thin shrink small outline, package mechanical data. . . . . . . . . . . . . . . . 30
Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
DocID4997 Rev 13
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
List of figures
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
8-pin package connections (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Bus master and memory devices on the serial bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
READ, WRITE, WEN, WDS sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
WRAL sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
ERASE, ERAL sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Write sequence with one clock glitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
AC testing input output waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Synchronous timing (start and op-code input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Synchronous timing (Read or Write). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Synchronous timing (Read or Write). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
PDIP8 – 8 lead plastic dual in-line package, 300 mils body width,
package outline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
SO8 narrow – 8 lead plastic small outline, 150 mils body width,
package outline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
UFDFPN8 8-lead ultra thin fine pitch dual flat package no lead
2 x 3 mm, outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
TSSOP8 – 8 lead thin shrink small outline, package outline . . . . . . . . . . . . . . . . . . . . . . . 30
DocID4997 Rev 13
5/33
Description
1
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
Description
The M93C46 (1 Kbit), M93C56 (2 Kbit), M93C66 (4 Kbit), M93C76 (8 Kbit) and M93C86
(16 Kbit) are Electrically Erasable PROgrammable Memory (EEPROM) devices accessed
through the MICROWIRE bus protocol. The memory array can be configured either in bytes
(x8b) or in words (x16b).
The M93Cx6 devices operate within a voltage supply range from 4.5 V to 5.5 V, the
M93Cx6-W devices operate within a voltage supply range from 2.5 V to 5.5 V, and the
M93Cx6-R devices operate within a voltage supply range from 1.8 V to 5.5 V. All these
devices operate with a clock frequency of 2 MHz (or less), over an ambient temperature
range of -40 °C / +85 °C.
Table 2. Memory size versus organization
Device
Number of bits
Number of 8-bit bytes
Number of 16-bit words
M93C86
16384
2048
1024
M93C76
8192
1024
512
M93C66
4096
512
256
M93C56
2048
256
128
M93C46
1024
128
64
Figure 1. Logic diagram
VCC
D
Q
C
M93Cx6
S
ORG
VSS
AI01928
6/33
DocID4997 Rev 13
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
Description
Table 3. Signal names
Signal name
Function
Direction
S
Chip Select
Input
D
Serial Data input
Input
Q
Serial Data output
Output
C
Serial Clock
Input
ORG
Organization Select
Input
VCC
Supply voltage
VSS
Ground
Figure 2. 8-pin package connections (top view)
M93Cx6
S
C
D
Q
1
2
3
4
8
7
6
5
VCC
DU
ORG
VSS
AI01929B
1. See Section 11: Package mechanical data for package dimensions, and how to identify pin-1.
2. DU = Don’t Use. The DU (do not use) pin does not contribute to the normal operation of the device. It is
reserved for use by STMicroelectronics during test sequences. The pin may be left unconnected or may be
connected to VCC or VSS.
DocID4997 Rev 13
7/33
Connecting to the serial bus
2
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
Connecting to the serial bus
Figure 3 shows an example of three memory devices connected to an MCU, on a serial bus.
Only one device is selected at a time, so only one device drives the Serial Data output (Q)
line at a time, the other devices are high impedance.
The pull-down resistor R (represented in Figure 3) ensures that no device is selected if the
bus master leaves the S line in the high impedance state.
In applications where the bus master may be in a state where all inputs/outputs are high
impedance at the same time (for example, if the bus master is reset during the transmission
of an instruction), the clock line (C) must be connected to an external pull-down resistor so
that, if all inputs/outputs become high impedance, the C line is pulled low (while the S line is
pulled low): this ensures that C does not become high at the same time as S goes low, and
so, that the tSLCH requirement is met. The typical value of R is 100 kΩ.
Figure 3. Bus master and memory devices on the serial bus
VSS
VCC
R
SDO
SDI
SCK
Bus master
C Q D
VCC
C Q D
VCC
VSS
R
M93xxx
memory device
R
C Q D
VCC
VSS
M93xxx
memory device
R
VSS
M93xxx
memory device
CS3 CS2 CS1
S
ORG
S
ORG
S
ORG
AI14377b
8/33
DocID4997 Rev 13
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
3
Operating features
3.1
Supply voltage (VCC)
3.1.1
Operating supply voltage (VCC)
Operating features
Prior to selecting the memory and issuing instructions to it, a valid and stable VCC voltage
within the specified [VCC(min), VCC(max)] range must be applied. In order to secure a stable
DC supply voltage, it is recommended to decouple the VCC line with a suitable capacitor
(usually of the order of 10 nF to 100 nF) close to the VCC/VSS package pins.
This voltage must remain stable and valid until the end of the transmission of the instruction
and, for a Write instruction, until the completion of the internal write cycle (tW).
3.1.2
Power-up conditions
When the power supply is turned on, VCC rises from VSS to VCC. During this time, the Chip
Select (S) line is not allowed to float and should be driven to VSS, it is therefore
recommended to connect the S line to VSS via a suitable pull-down resistor.
The VCC rise time must not vary faster than 1 V/µs.
3.1.3
Power-up and device reset
In order to prevent inadvertent Write operations during power-up, a power on reset (POR)
circuit is included. At power-up (continuous rise of VCC), the device does not respond to any
instruction until VCC has reached the power on reset threshold voltage (this threshold is
lower than the minimum VCC operating voltage defined in Operating conditions, in
Section 10: DC and AC parameters).
When VCC passes the POR threshold, the device is reset and is in the following state:
3.1.4
•
Standby Power mode
•
deselected (assuming that there is a pull-down resistor on the S line)
Power-down
At power-down (continuous decrease in VCC), as soon as VCC drops from the normal
operating voltage to below the power on reset threshold voltage, the device stops
responding to any instruction sent to it.
During power-down, the device must be deselected and in the Standby Power mode (that is,
there should be no internal Write cycle in progress).
DocID4997 Rev 13
9/33
Memory organization
4
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
Memory organization
The M93Cx6 memory is organized either as bytes (x8) or as words (x16). If Organization
Select (ORG) is left unconnected (or connected to VCC) the x16 organization is selected;
when Organization Select (ORG) is connected to Ground (VSS) the x8 organization is
selected. When the M93Cx6 is in Standby mode, Organization Select (ORG) should be set
either to VSS or VCC for minimum power consumption. Any voltage between VSS and VCC
applied to Organization Select (ORG) may increase the Standby current.
10/33
DocID4997 Rev 13
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
5
Instructions
Instructions
The instruction set of the M93Cx6 devices contains seven instructions, as summarized in
Table 4 to Table 6. Each instruction consists of the following parts, as shown in Figure 4:
READ, WRITE, WEN, WDS sequences:
•
Each instruction is preceded by a rising edge on Chip Select Input (S) with Serial Clock
(C) being held low.
•
A start bit, which is the first ‘1’ read on Serial Data Input (D) during the rising edge of
Serial Clock (C).
•
Two op-code bits, read on Serial Data Input (D) during the rising edge of Serial Clock
(C). (Some instructions also use the first two bits of the address to define the op-code).
•
The address bits of the byte or word that is to be accessed. For the M93C46, the
address is made up of 6 bits for the x16 organization or 7 bits for the x8 organization
(see Table 4). For the M93C56 and M93C66, the address is made up of 8 bits for the
x16 organization or 9 bits for the x8 organization (see Table 5). For the M93C76 and
M93C86, the address is made up of 10 bits for the x16 organization or 11 bits for the x8
organization (see Table 6).
The M93Cx6 devices are fabricated in CMOS technology and are therefore able to run as
slow as 0 Hz (static input signals) or as fast as the maximum ratings specified in “AC
characteristics” tables, in Section 10: DC and AC parameters.
Table 4. Instruction set for the M93C46
x8 origination (ORG = 0)
Instruction
Description
Start
bit
Opcode
Address
(1)
Data
READ
Read Data from
Memory
1
10
A6-A0
Q7-Q0
WRITE
Write Data to
Memory
1
01
A6-A0
D7-D0
WEN
Write Enable
1
00
WDS
Write Disable
1
ERASE
Erase Byte or
Word
ERAL
WRAL
x16 origination (ORG = 1)
Required
Address
clock
(1)
cycles
Data
Required
clock
cycles
A5-A0
Q15-Q0
18
A5-A0
D15-D0
11X XXXX
10
11 XXXX
9
00
00X
XXXX
10
00 XXXX
9
1
11
A6-A0
10
A5-A0
9
Erase All Memory
1
00
10X
XXXX
10
10 XXXX
9
Write All Memory
with same Data
1
00
01X
XXXX
18
01 XXXX D15-D0
25
D7-D0
25
1. X = Don't Care bit.
DocID4997 Rev 13
11/33
Instructions
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
Table 5. Instruction set for the M93C56 and M93C66
x8 origination (ORG = 0)
Instruction
Description
Start Opbit code
Address
(1) (2)
Data
x16 origination (ORG = 1)
Required Address
(1) (3)
clock cycles
READ
Read Data from
Memory
1
10
A8-A0
Q7-Q0
WRITE
Write Data to
Memory
1
01
A8-A0
D7-D0
WEN
Write Enable
1
00
WDS
Write Disable
1
ERASE
Erase Byte or
Word
ERAL
WRAL
Data
Required
clock cycles
A7-A0
Q15-Q0
20
A7-A0
D15-D0
1 1XXX
XXXX
12
11XX
XXXX
11
00
0 0XXX
XXXX
12
00XX
XXXX
11
1
11
A8-A0
12
A7-A0
11
Erase All
Memory
1
00
1 0XXX
XXXX
12
10XX
XXXX
11
Write All Memory
with same Data
1
00
0 1XXX
XXXX
20
01XX
XXXX
D7-D0
D15-D0
27
27
1. X = Don't Care bit.
2. Address bit A8 is not decoded by the M93C56.
3. Address bit A7 is not decoded by the M93C56.
Table 6. Instruction set for the M93C76 and M93C86
x8 Origination (ORG = 0)
Instruction
Description
Start Opbit code Address(1),
(2)
Data
READ
Read Data from
Memory
1
10
A10-A0
Q7-Q0
WRITE
Write Data to
Memory
1
01
A10-A0
D7-D0
WEN
Write Enable
1
00
WDS
Write Disable
1
ERASE
Erase Byte or Word
ERAL
WRAL
Required
Address
clock
(1) (3)
cycles
Data
Required
clock
cycles
A9-A0
Q15-Q0
22
A9-A0
D15-D0
11X XXXX
XXXX
14
11 XXXX
XXXX
13
00
00X XXXX
XXXX
14
00 XXXX
XXXX
13
1
11
A10-A0
14
A9-A0
13
Erase All Memory
1
00
10X XXXX
XXXX
14
10 XXXX
XXXX
13
Write All Memory
with same Data
1
00
01X XXXX
XXXX
22
01 XXXX
D15-D0
XXXX
29
D7-D0
1. X = Don't Care bit.
2. Address bit A10 is not decoded by the M93C76.
3. Address bit A9 is not decoded by the M93C76.
12/33
x16 Origination (ORG = 1)
DocID4997 Rev 13
29
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
5.1
Instructions
Read Data from Memory
The Read Data from Memory (READ) instruction outputs data on Serial Data Output (Q).
When the instruction is received, the op-code and address are decoded, and the data from
the memory is transferred to an output shift register. A dummy 0 bit is output first, followed
by the 8-bit byte or 16-bit word, with the most significant bit first. Output data changes are
triggered by the rising edge of Serial Clock (C). The M93Cx6 automatically increments the
internal address register and clocks out the next byte (or word) as long as the Chip Select
Input (S) is held High. In this case, the dummy 0 bit is not output between bytes (or words)
and a continuous stream of data can be read (the address counter automatically rolls over
to 00h when the highest address is reached).
5.2
Erase and Write data
5.2.1
Write Enable and Write Disable
The Write Enable (WEN) instruction enables the future execution of erase or write
instructions, and the Write Disable (WDS) instruction disables it. When power is first
applied, the M93Cx6 initializes itself so that erase and write instructions are disabled. After a
Write Enable (WEN) instruction has been executed, erasing and writing remains enabled
until a Write Disable (WDS) instruction is executed, or until VCC falls below the power-on
reset threshold voltage. To protect the memory contents from accidental corruption, it is
advisable to issue the Write Disable (WDS) instruction after every write cycle. The Read
Data from Memory (READ) instruction is not affected by the Write Enable (WEN) or Write
Disable (WDS) instructions.
5.2.2
Write
For the Write Data to Memory (WRITE) instruction, 8 or 16 data bits follow the op-code and
address bits. These form the byte or word that is to be written. As with the other bits, Serial
Data Input (D) is sampled on the rising edge of Serial Clock (C).
After the last data bit has been sampled, the Chip Select Input (S) must be taken low before
the next rising edge of Serial Clock (C). If Chip Select Input (S) is brought low before or after
this specific time frame, the self-timed programming cycle will not be started, and the
addressed location will not be programmed. The completion of the cycle can be detected by
monitoring the READY/BUSY line, as described later in this document.
Once the Write cycle has been started, it is internally self-timed (the external clock signal on
Serial Clock (C) may be stopped or left running after the start of a Write cycle). The Write
cycle is automatically preceded by an Erase cycle, so it is unnecessary to execute an
explicit erase instruction before a Write Data to Memory (WRITE) instruction.
DocID4997 Rev 13
13/33
Instructions
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
Figure 4. READ, WRITE, WEN, WDS sequences
Read
S
D
1 1 0 An
A0
Qn
Q
ADDR
Q0
DATA OUT
OP
CODE
Write
S
CHECK
STATUS
D
1 0 1 An
A0 Dn
D0
Q
ADDR
DATA IN
BUSY
READY
OP
CODE
Write
Enable
S
D
Write
Disable
1 0 0 1 1 Xn X0
S
D
OP
CODE
1 0 0 0 0 Xn X0
OP
CODE
AI00878d
1. For the meanings of An, Xn, Qn and Dn, see Table 4, Table 5 and Table 6.
14/33
DocID4997 Rev 13
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
5.2.3
Instructions
Write All
As with the Erase All Memory (ERAL) instruction, the format of the Write All Memory with
same Data (WRAL) instruction requires that a dummy address be provided. As with the
Write Data to Memory (WRITE) instruction, the format of the Write All Memory with same
Data (WRAL) instruction requires that an 8-bit data byte, or 16-bit data word, be provided.
This value is written to all the addresses of the memory device. The completion of the cycle
can be detected by monitoring the READY/BUSY line, as described next.
Figure 5. WRAL sequence
WRITE
ALL
S
CHECK
STATUS
D
1 0 0 0 1 Xn X0 Dn
D0
Q
ADDR
DATA IN
BUSY
READY
OP
CODE
AI00880C
1. For the meanings of Xn and Dn, please see Table 4, Table 5 and Table 6.
DocID4997 Rev 13
15/33
Instructions
5.2.4
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
Erase Byte or Word
The Erase Byte or Word (ERASE) instruction sets the bits of the addressed memory byte (or
word) to 1. Once the address has been correctly decoded, the falling edge of the Chip
Select Input (S) starts the self-timed Erase cycle. The completion of the cycle can be
detected by monitoring the READY/BUSY line, as described in Section 6: READY/BUSY
status.
Figure 6. ERASE, ERAL sequences
ERASE
S
CHECK
STATUS
D
1 1 1 An
A0
Q
ADDR
BUSY
READY
OP
CODE
ERASE
ALL
S
CHECK
STATUS
D
1 0 0 1 0 Xn X0
Q
ADDR
BUSY
READY
OP
CODE
AI00879B
1. For the meanings of An and Xn, please see Table 4, Table 5 and Table 6.
5.2.5
Erase All
The Erase All Memory (ERAL) instruction erases the whole memory (all memory bits are set
to 1). The format of the instruction requires that a dummy address be provided. The Erase
cycle is conducted in the same way as the Erase instruction (ERASE). The completion of
the cycle can be detected by monitoring the READY/BUSY line, as described in Section 6:
READY/BUSY status.
16/33
DocID4997 Rev 13
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
6
READY/BUSY status
READY/BUSY status
While the Write or Erase cycle is underway, for a WRITE, ERASE, WRAL or ERAL
instruction, the Busy signal (Q=0) is returned whenever Chip Select input (S) is driven high.
(Please note, though, that there is an initial delay, of tSLSH, before this status information
becomes available). In this state, the M93Cx6 ignores any data on the bus. When the Write
cycle is completed, and Chip Select Input (S) is driven high, the Ready signal (Q=1)
indicates that the M93Cx6 is ready to receive the next instruction. Serial Data Output (Q)
remains set to 1 until the Chip Select Input (S) is brought low or until a new start bit is
decoded.
7
Initial delivery state
The device is delivered with all bits in the memory array set to 1 (each byte contains FFh).
DocID4997 Rev 13
17/33
Clock pulse counter
8
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
Clock pulse counter
In a noisy environment, the number of pulses received on Serial Clock (C) may be greater
than the number delivered by the master (the microcontroller). This can lead to a
misalignment of the instruction of one or more bits (as shown in Figure 7) and may lead to
the writing of erroneous data at an erroneous address.
To avoid this problem, the M93Cx6 has an on-chip counter that counts the clock pulses from
the start bit until the falling edge of the Chip Select Input (S). If the number of clock pulses
received is not the number expected, the WRITE, ERASE, ERAL or WRAL instruction is
aborted, and the contents of the memory are not modified.
The number of clock cycles expected for each instruction, and for each member of the
M93Cx6 family, are summarized in Table 4: Instruction set for the M93C46 to Table 6:
Instruction set for the M93C76 and M93C86. For example, a Write Data to Memory (WRITE)
instruction on the M93C56 (or M93C66) expects 20 clock cycles (for the x8 organization)
from the start bit to the falling edge of Chip Select Input (S). That is:
1 Start bit
+ 2 Op-code bits
+ 9 Address bits
+ 8 Data bits
Figure 7. Write sequence with one clock glitch
S
C
D
An
START
"0"
"1"
An-1
An-2
Glitch
D0
ADDRESS AND DATA
ARE SHIFTED BY ONE BIT
WRITE
AI01395
18/33
DocID4997 Rev 13
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
9
Maximum rating
Maximum rating
Stressing the device outside the ratings listed in the Absolute maximum ratings table may
cause permanent damage to the device. These are stress ratings only, and operation of the
device at these, or any other conditions outside those indicated in the operating sections of
this specification, is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability.
Table 7. Absolute maximum ratings
Symbol
TSTG
Parameter
Min.
Max.
Unit
Ambient operating temperature
–40
130
°C
Storage temperature
–65
150
°C
260(1)
PDIP
TLEAD
Lead temperature during soldering
VOUT
Output range (Q = VOH or Hi-Z)
–0.50
VCC+0.5
V
VIN
Input range
–0.50
VCC+1
V
VCC
Supply voltage
–0.50
6.5
V
4000
V
VESD
other packages
Electrostatic discharge voltage (human body
model)(3)
See note (2)
°C
1. TLEAD max must not be applied for more than 10 s.
2. Compliant with JEDEC Std J-STD-020D (for small body, Sn-Pb or Pb-free assembly), the ST
ECOPACK® 7191395 specification, and the European directive on Restrictions of Hazardous
Substances (RoHS) 2011/65/EU.
3. Positive and negative pulses applied on pin pairs, according to the AEC-Q100-002 (compliant
with JEDEC Std JESD22-A114, C1 = 100pF, R1 = 1500Ω, R2 = 500Ω).
DocID4997 Rev 13
19/33
DC and AC parameters
10
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
DC and AC parameters
This section summarizes the operating and measurement conditions, and the dc and ac
characteristics of the device. The parameters in the dc and ac characteristic tables that
follow are derived from tests performed under the measurement conditions summarized in
the relevant tables. Designers should check that the operating conditions in their circuit
match the measurement conditions when relying on the quoted parameters.
Table 8. Operating conditions (M93Cx6)
Symbol
VCC
TA
Parameter
Min.
Max.
Unit
Supply voltage
4.5
5.5
V
Ambient operating temperature
–40
85
°C
Min.
Max.
Unit
Supply voltage
2.5
5.5
V
Ambient operating temperature
–40
85
°C
Min.
Max.
Unit
Supply voltage
1.8
5.5
V
Ambient operating temperature
–40
85
°C
Max.
Unit
Table 9. Operating conditions (M93Cx6-W)
Symbol
VCC
TA
Parameter
Table 10. Operating conditions (M93Cx6-R)
Symbol
VCC
TA
Parameter
Table 11. AC measurement conditions (M93Cx6)
Symbol
CL
Parameter
Min.
Load capacitance
100
Input rise and fall times
Input voltage levels
pF
50
ns
0.4 V to 2.4 V
V
Input timing reference voltages
1.0 V and 2.0 V
V
Output timing reference voltages
0.8 V and 2.0 V
V
Table 12. AC measurement conditions (M93Cx6-W and M93Cx6-R)
Symbol
CL
Parameter
Load capacitance
Max.
100
Input rise and fall times
20/33
Min.
Unit
pF
50
ns
Input voltage levels
0.2 VCC to 0.8 VCC
V
Input timing reference voltages
0.3 VCC to 0.7 VCC
V
Output timing reference voltages
0.3 VCC to 0.7 VCC
V
DocID4997 Rev 13
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
DC and AC parameters
Figure 8. AC testing input output waveforms
M93CXX
2.4V
2V
2.0V
1V
0.8V
Input and output
timing reference levels
Input voltage levels
0.4V
Input
Output
M93CXX-W and M93CXX-R
0.8VCC
0.7VCC
Input voltage levels
0.3VCC
0.2VCC
Input and output
timing reference levels
MS19788V2
Table 13. Capacitance
Symbol
Parameter
COUT
Output capacitance
CIN
Input capacitance
Test condition(1)
Min
Max
Unit
VOUT = 0V
5
pF
VIN = 0V
5
pF
1. Sampled only, not 100% tested, at TA = 25 °C and a frequency of 1 MHz.
Table 14. DC characteristics (M93Cx6, device grade 6)
Symbol
Parameter
Test condition
Min.
Max.
Unit
0V ≤ VIN ≤ VCC
±2.5
µA
0V ≤ VOUT ≤ VCC, Q in Hi-Z
±2.5
µA
ILI
Input leakage current
ILO
Output leakage current
ICC
Supply current
VCC = 5 V, S = VIH, f = 2 MHz,
Q = open
2
mA
ICC1
Supply current (Standby)
VCC = 5 V, S = VSS, C = VSS,
ORG = VSS or VCC,
pin7 = VCC, VSS or Hi-Z
15
µA
VIL(1)
Input low voltage
VCC = 5 V ± 10%
–0.45
0.8
V
Input high voltage
VCC = 5 V ± 10%
2
VCC + 1
V
VOL(1)
Output low voltage
VCC = 5 V, IOL = 2.1 mA
0.4
V
VOH(1)
Output high voltage
VCC = 5 V, IOH = –400 µA
VIH
(1)
0.8VCC
V
1. Please note that the input and output levels defined in this table are compatible with TTL logic
levels and are NOT fully compatible with CMOS levels (as defined in Table 15).
DocID4997 Rev 13
21/33
DC and AC parameters
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
Table 15. DC characteristics (M93Cx6-W, device grade 6)
Symbol
Parameter
Test condition
ILI
Input leakage current
ILO
Output leakage current
ICC
Supply current (CMOS
inputs)
ICC1
Supply current (Standby)
VIL
Input low voltage (D, C, S)
VIH
Input high voltage (D, C,
S)
VOL
Output low voltage (Q)
VOH
Output high voltage (Q)
Min.
Max.
Unit
0V ≤ VIN ≤ VCC
±2.5
µA
0V ≤ VOUT ≤ VCC, Q in Hi-Z
±2.5
µA
VCC = 5 V, S = VIH, f = 2 MHz,
Q = open
2
mA
VCC = 2.5 V, S = VIH, f = 2 MHz,
Q = open
1
mA
VCC = 2.5 V, S = VSS, C = VSS,
ORG = VSS or VCC,
pin7 = VCC, VSS or Hi-Z
5
µA
0.2 VCC
V
0.7 VCC VCC + 1
V
–0.45
VCC = 5 V, IOL = 2.1 mA
0.4
V
VCC = 2.5 V, IOL = 100 µA
0.2
V
VCC = 5 V, IOH = –400 µA
0.8 VCC
V
VCC = 2.5 V, IOH = –100 µA
VCC–0.2
V
Table 16. DC characteristics (M93Cx6-R)
Symbol
Parameter
Test condition
ILI
Input leakage current
ILO
Output leakage current
ICC
Supply current (CMOS
inputs)
Min.(1)
Max. (1) Unit
0V ≤ VIN ≤ VCC
±2.5
µA
0V ≤ VOUT ≤ VCC, Q in Hi-Z
±2.5
µA
VCC = 5 V, S = VIH, f = 2 MHz,
Q = open
2
mA
VCC = 1.8 V, S = VIH, f = 1 MHz,
Q = open
1
mA
VCC = 1.8 V, S = VSS, C = VSS,
ORG = VSS or VCC,
pin7 = VCC, VSS or Hi-Z
2
µA
–0.45
0.2 VCC
V
0.8 VCC
VCC + 1
V
0.2
V
ICC1
Supply current (Standby)
VIL
Input low voltage (D, C, S)
VIH
Input high voltage (D, C,
S)
VOL
Output low voltage (Q)
VCC = 1.8 V, IOL = 100 µA
VOH
Output high voltage (Q)
VCC = 1.8 V, IOH = –100 µA
VCC–0.2
1. This product is under development. For more information, please contact your nearest ST
sales office.
22/33
DocID4997 Rev 13
V
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
DC and AC parameters
Table 17. AC characteristics (M93Cx6, device grade 6)
Test conditions specified in Table 8 and Table 11
Symbol
Alt.
fC
fSK
tSLCH
tSHCH
tCSS
Parameter
Clock frequency
Min.
Max.
Unit
D.C.
2
MHz
Chip Select low to Clock high
50
ns
Chip Select setup time
M93C46, M93C56, M93C66
50
ns
Chip Select setup time
M93C76, M93C86
50
ns
tSLSH(1)
tCS
Chip Select low to Chip Select high
200
ns
tCHCL(2)
tSKH
Clock high time
200
ns
tCLCH(2)
tSKL
Clock low time
200
ns
tDVCH
tDIS
Data in setup time
50
ns
tCHDX
tDIH
Data in hold time
50
ns
tCLSH
tSKS
Clock setup time (relative to S)
50
ns
tCLSL
tCSH
Chip Select hold time
0
ns
tSHQV
tSV
Chip Select to READY/BUSY status
200
ns
tSLQZ
tDF
Chip Select low to output Hi-Z
100
ns
tCHQL
tPD0
Delay to output low
200
ns
tCHQV
tPD1
Delay to output valid
200
ns
tW
tWP
Erase or Write cycle time
5
ms
1. Chip Select Input (S) must be brought low for a minimum of tSLSH between consecutive
instruction cycles.
2. tCHCL + tCLCH ≥ 1 / fC.
DocID4997 Rev 13
23/33
DC and AC parameters
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
Table 18. AC characteristics (M93Cx6-W, device grade 6)
Test conditions specified in Table 9 and Table 12
Symbol
Alt.
fC
fSK
tSLSH
(1)
Clock frequency
Min.
Max.
Unit
D.C.
2
MHz
Chip Select low to Clock high
50
ns
tCSS
Chip Select setup time
50
ns
tSLCH
tSHCH
Parameter
tCS
Chip Select low to Chip Select high
200
ns
tCHCL(2)
tSKH
Clock high time
200
ns
tCLCH(2)
tSKL
Clock low time
200
ns
tDVCH
tDIS
Data in setup time
50
ns
tCHDX
tDIH
Data in hold time
50
ns
tCLSH
tSKS
Clock setup time (relative to S)
50
ns
tCLSL
tCSH
Chip Select hold time
0
ns
tSHQV
tSV
Chip Select to READY/BUSY status
200
ns
tSLQZ
tDF
Chip Select low to output Hi-Z
100
ns
tCHQL
tPD0
Delay to output low
200
ns
tCHQV
tPD1
Delay to output valid
200
ns
tW
tWP
Erase or Write cycle time
5
ms
1. Chip Select Input (S) must be brought low for a minimum of tSLSH between consecutive
instruction cycles.
2. tCHCL + tCLCH ≥ 1 / fC.
24/33
DocID4997 Rev 13
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
DC and AC parameters
Table 19. AC characteristics (M93Cx6-R)
Test conditions specified in Table 10 and Table 12
Symbol
Alt.
fC
fSK
tSLCH
Min.(1)
Max.(1)
Unit
Clock frequency
D.C.
1
MHz
Chip Select low to Clock high
250
ns
Parameter
tSHCH
tCSS
Chip Select setup time
50
ns
tSLSH(2)
tCS
Chip Select low to Chip Select high
250
ns
tCHCL
(3)
tSKH
Clock high time
250
ns
tCLCH
(3)
tSKL
Clock low time
250
ns
tDVCH
tDIS
Data in setup time
100
ns
tCHDX
tDIH
Data in hold time
100
ns
tCLSH
tSKS
Clock setup time (relative to S)
100
ns
tCLSL
tCSH
Chip Select hold time
0
ns
tSHQV
tSV
Chip Select to READY/BUSY status
400
ns
tSLQZ
tDF
Chip Select low to output Hi-Z
200
ns
tCHQL
tPD0
Delay to output low
400
ns
tCHQV
tPD1
Delay to output valid
400
ns
tW
tWP
Erase or Write cycle time
10
ms
1. This product is under development. For more information, please contact your nearest ST
sales office.
2. Chip Select Input (S) must be brought low for a minimum of tSLSH between consecutive
instruction cycles.
3. tCHCL + tCLCH ≥ 1 / fC.
Figure 9. Synchronous timing (start and op-code input)
tCLSH
tCHCL
C
tSHCH
tCLCH
S
tDVCH
D
START
tCHDX
OP CODE
START
OP CODE
OP CODE INPUT
AI01428
DocID4997 Rev 13
25/33
DC and AC parameters
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
Figure 10. Synchronous timing (Read or Write)
C
tCLSL
S
tDVCH
D
tCHDX
tCHQV
tSLSH
A0
An
tSLQZ
tCHQL
Hi-Z
Q
Q15/Q7
ADDRESS INPUT
Q0
DATA OUTPUT
AI00820C
Figure 11. Synchronous timing (Read or Write)
tSLCH
C
tCLSL
S
tDVCH
An
D
tCHDX
tSLSH
A0/D0
tSHQV
tSLQZ
Hi-Z
Q
BUSY
READY
tW
ADDRESS/DATA INPUT
WRITE CYCLE
AI01429
26/33
DocID4997 Rev 13
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
11
Package mechanical data
Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark .
Figure 12. PDIP8 – 8 lead plastic dual in-line package, 300 mils body width,
package outline
E
b2
A2
A1
b
A
L
c
e
eA
eB
D
8
E1
1
PDIP-B
1. Drawing is not to scale.
Table 20. PDIP8 – 8 lead plastic dual in-line package, 300 mils body width,
package mechanical data
inches(1)
millimeters
Symbol
Typ.
Min.
Max.
Typ.
Min.
Max.
A
-
-
5.33
-
-
0.2098
A1
-
0.38
-
-
0.015
-
A2
3.3
2.92
4.95
0.1299
0.115
0.1949
b
0.46
0.36
0.56
0.0181
0.0142
0.022
b2
1.52
1.14
1.78
0.0598
0.0449
0.0701
c
0.25
0.2
0.36
0.0098
0.0079
0.0142
D
9.27
9.02
10.16
0.365
0.3551
0.4
E
7.87
7.62
8.26
0.3098
0.3
0.3252
E1
6.35
6.1
7.11
0.25
0.2402
0.2799
e
2.54
-
-
0.1
-
-
eA
7.62
-
-
0.3
-
-
eB
-
-
10.92
-
-
0.4299
L
3.3
2.92
3.81
0.1299
0.115
0.15
1. Values in inches are converted from mm and rounded to 4 decimal digits.
DocID4997 Rev 13
27/33
Package mechanical data
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
Figure 13. SO8 narrow – 8 lead plastic small outline, 150 mils body width,
package outline
h x 45˚
A2
A
c
ccc
b
e
0.25 mm
GAUGE PLANE
D
k
8
E1
E
1
L
A1
L1
SO-A
1. Drawing is not to scale.
Table 21. SO8 narrow – 8 lead plastic small outline, 150 mils body width, package data
inches(1)
millimeters
Symbol
Typ
Min
Max
Typ
Min
Max
A
-
-
1.75
-
-
0.0689
A1
-
0.1
0.25
-
0.0039
0.0098
A2
-
1.25
-
-
0.0492
-
b
-
0.28
0.48
-
0.011
0.0189
c
-
0.17
0.23
-
0.0067
0.0091
ccc
-
-
0.1
-
-
0.0039
D
4.9
4.8
5
0.1929
0.189
0.1969
E
6
5.8
6.2
0.2362
0.2283
0.2441
E1
3.9
3.8
4
0.1535
0.1496
0.1575
e
1.27
-
-
0.05
-
-
h
-
0.25
0.5
-
0.0098
0.0197
k
-
0°
8°
-
0°
8°
L
-
0.4
1.27
-
0.0157
0.05
L1
1.04
-
-
0.0409
-
-
1. Values in inches are converted from mm and rounded to 4 decimal digits.
28/33
DocID4997 Rev 13
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
Package mechanical data
Figure 14. UFDFPN8 8-lead ultra thin fine pitch dual flat package no lead
2 x 3 mm, outline
e
D
b
L1
L3
Pin 1
E
E2
K
L
A
D2
eee
A1
ZW_MEeV2
1. Drawing is not to scale.
2. The central pad (area E2 by D2 in the above illustration) is pulled, internally, to VSS. It must not be allowed
to be connected to any other voltage or signal line on the PCB, for example during the soldering process.
3. The circle in the top view of the package indicates the position of pin 1.
Table 22. UFDFPN8 8-lead ultra thin fine pitch dual flat package no lead
2 x 3 mm, data
inches(1)
millimeters
Symbol
Typ
Min
Max
Typ
Min
Max
A
0.550
0.450
0.600
0.0217
0.0177
0.0236
A1
0.020
0.000
0.050
0.0008
0.0000
0.0020
b
0.250
0.200
0.300
0.0098
0.0079
0.0118
D
2.000
1.900
2.100
0.0787
0.0748
0.0827
D2 (rev MC)
-
1.200
1.600
-
0.0472
0.0630
E
3.000
2.900
3.100
0.1181
0.1142
0.1220
E2 (rev MC)
-
1.200
1.600
-
0.0472
0.0630
e
0.500
-
-
0.0197
-
-
K (rev MC)
-
0.300
-
-
0.0118
-
L
-
0.300
0.500
-
0.0118
0.0197
L1
-
-
0.150
-
-
0.0059
L3
-
0.300
-
-
0.0118
-
-
0.080
-
-
0.0031
-
eee
(2)
1. Values in inches are converted from mm and rounded to four decimal digits.
2. Applied for exposed die paddle and terminals. Exclude embedding part of exposed die paddle
from measuring.
DocID4997 Rev 13
29/33
Package mechanical data
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
Figure 15. TSSOP8 – 8 lead thin shrink small outline, package outline
D
8
5
c
E1
1
E
4
α
A1
A
L
A2
L1
CP
b
e
TSSOP8AM
1. Drawing is not to scale.
Table 23. TSSOP8 – 8 lead thin shrink small outline, package mechanical data
inches(1)
millimeters
Symbol
Typ.
Min.
Max.
Typ.
Min.
Max.
A
-
-
1.2
-
-
0.0472
A1
-
0.05
0.15
-
0.002
0.0059
A2
1
0.8
1.05
0.0394
0.0315
0.0413
b
-
0.19
0.3
-
0.0075
0.0118
c
-
0.09
0.2
-
0.0035
0.0079
CP
-
-
0.1
-
-
0.0039
D
3
2.9
3.1
0.1181
0.1142
0.122
e
0.65
-
-
0.0256
-
-
E
6.4
6.2
6.6
0.252
0.2441
0.2598
E1
4.4
4.3
4.5
0.1732
0.1693
0.1772
L
0.6
0.45
0.75
0.0236
0.0177
0.0295
L1
1
-
-
0.0394
-
-
α
-
0°
8°
-
0°
8°
N (pin number)
8
1. Values in inches are converted from mm and rounded to 4 decimal digits.
30/33
DocID4997 Rev 13
8
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
12
Part numbering
Part numbering
Table 24. Ordering information scheme
Example:
M93C86
–
W MN 6
T
P
Device type
M93 = MICROWIRE serial EEPROM
Device function
86 = 16 Kbit (2048 x 8)
76 = 8 Kbit (1024 x 8)
66 = 4 Kbit (512 x 8)
56 = 2 Kbit (256 x 8)
46 = 1 Kbit (128 x 8)
Operating voltage
blank = VCC = 4.5 to 5.5 V
W = VCC = 2.5 to 5.5 V
R = VCC = 1.8 to 5.5 V
Package
BN = PDIP8
MN = SO8 (150 mils width)
MC = UFDFPN8 2 x 3 mm (MLP8)
DW = TSSOP8 (169 mils width)
Device grade
6 = Industrial temperature range, –40 to 85 °C.
Device tested with standard test flow
Packing
blank = standard packing
T = tape and reel packing
Plating technology
P or G = ECOPACK® (RoHS compliant)
For a list of available options (speed, package, etc.) or for further information on any aspect
of this device, please contact your nearest ST sales office.
DocID4997 Rev 13
31/33
Revision history
13
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
Revision history
Table 25. Document revision history
Date
Revision
Changes
01-Apr-2010
9
Modified footnote in Table 14 and Table 15 on page 23
Updated Figure 14: UFDFPN8 (MLP8) 8-lead ultra thin fine pitch dual
flat package no lead 2 x 3 mm, outline and Table 22: UFDFPN8 (MLP8)
8-lead ultra thin fine pitch dual flat package no lead 2 x 3 mm, data
29-Apr-2010
10
Updated Figure 31: Available M93C66-x products (package, voltage
range, temperature grade) UFDFPN option.
12-Apr-2011
11
Updated Table 7: Absolute maximum ratings, MLP8 package data in
Section 12: Package mechanical data and process data in Section 9:
Clock pulse counter.
Deleted Table 29: Available M93C46-x products (package, voltage
range, temperature grade), Table 30: Available M93C56-x products
(package, voltage range, temperature grade), Table 31: Available
M93C66-x products (package, voltage range, temperature grade),
Table 32: Available M93C76-x products (package, voltage range,
temperature grade) and Table 33: Available M93C86-x products
(package, voltage range, temperature grade).
05-Oct-2011
12
Updated Table 1: Device summary and Table 8: Operating conditions
(M93Cx6).
Modified footnote 2 in Table 7.
13
Document reformatted.
Updated:
– Part number names
– Table 1: Device summary and package figure on cover page
– Section 1: Description
– Introductory paragraph in Section 9: Maximum rating
– Note (2) under Table 7: Absolute maximum ratings
– Table 8: Operating conditions (M93Cx6) and Table 9: Operating
conditions (M93Cx6-W)
– Introductory paragraph in Section 11: Package mechanical data
– Figure 14: UFDFPN8 8-lead ultra thin fine pitch dual flat package no
lead 2 x 3 mm, outline and Table 22: UFDFPN8 8-lead ultra thin fine
pitch dual flat package no lead 2 x 3 mm, data
– Table 24: Ordering information scheme
Renamed:
– Figure 2: 8-pin package connections (top view)
– Table 17: AC characteristics (M93Cx6, device grade 6)
Deleted:
– Section: Common I/O operation
– Table: DC characteristics (M93Cx6, device grade 3), Table: DC
characteristics (M93Cx6-W, device grade 3), and Table: AC
characteristics (M93Cx6-W, device grade 3)
23-Apr-2013
32/33
DocID4997 Rev 13
M93C86xx M93C76xx M93C66xx M93C56xx M93C46xx
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT AUTHORIZED FOR USE IN WEAPONS. NOR ARE ST PRODUCTS DESIGNED OR AUTHORIZED FOR USE
IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH
PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR
ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED
FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN
WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE,
AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS.
PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE
CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2013 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
DocID4997 Rev 13
33/33
Similar pages