Emcore MAFA2023-FC-03 Erbium doped fiber micro amplifier Datasheet

MAFA 2000 Series EDFA
DATASHEET | AUGUST 2012
FIBER OPTICS
MAFA 2000 Series Erbium Doped Fiber Micro Amplifier
EMCORE’s MAFA 2000 Series Erbium Doped Fiber Amplifier (EDFA) Gain Block
Module is an ideal building block for OEM system integrators. The family of MAFA
2000 EDFA Gain Blocks is designed to meet the most demanding noise
performance requirements of high performance networks, and performs all the
functions required of an optical amplifier for system integration.
Applications
Microwave and RF Optical Fiber
Distribution Systems
EW Systems
Free Space Optical Communications
DWDM Networks
Video and Data Transport Networks
MAFA2000 series EDFA Gain Blocks provide optical isolation on the input and
output of the gain block for stable, low noise operation. The input and output
optical signal power levels are detected for monitoring and control. The input
optical signal is amplified with active gain control for a constant output power level
or with active output power control for constant gain mode operation.
The MAFA 2000 series EDFA Gain Blocks also provide monitors and associated
alarms for all critical operating parameters. The optical output of the MAFA 2000
series EDFA Gain Blocks also provide monitors and associated alarms for all vital
characteristics. The optical output of the MAFA 2000 series EDFA Gain Blocks
can be split into multiple ports by an optional external splitter.
Laboratory Optical Sources
High Performance Supertrunking Links
High Power Distribtuion Networks
Redundanct Ring Architectures
FTTx Networks
Features
Full Function Fiber Optic Amplifier Gain
Block Ready for Integration
Low Noise Figure (Typ < 5 dB)
Input Power Range io – 10 dBm to +12
dBm and +14 dBm to +27 dBm Output
Power
Standard RS-232 Communication (RS485 or I2C is optional)
Standard and Optional Gain Flatness
(1530 nm – 1562 nm)
Low Electrical Power Consumption
| REV 2012.08
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
MAFA 2000 Series EDFA
FIBER OPTICS
DATASHEET | AUGUST 2012
Optical/Electrical Characteristics1
Property
Operating Input
Power
Operating Input
Power
Unit
Models
Limit
Comments
2014
2017
2020
2023
2024
2027
Pin (dBm)
Max
12
12
12
12
12
12
Pin (dBm)
Min
-10
-10
-10
-10
-10
-10
Typical
(May vary for some models)
Output Power
Po(dBm)
Nominal
14
+/-.20
17
+/-.20
20
+/-.20
23
+/-.25
24
+/-.20
27
+/-.20
Note 2
Noise Figure
NF (dB)
Typ/Max
4.5/5.0
4.5/5.0
4.5/5.0
4.5/5.0
5.0/5.5
5.0/5.5
(Notes 3, 8)
Gs (dB)
Max
+/-0.5
+/-0.5
+/-0.5
+/-0.5
+/-0.5
+/-0.5
(Notes 4)
Gd (dB)
Max
+/-1.0
+/-1.25
+/-1.5
+/-2.0
+/-2.0
+/-2.0
(Notes 5, 7)
(dB)
Max
+/- 0.2
+/- 0.2
+/- 0.2
+/- 0.2
+/- 0.2
+/-0.2
(Note 6)
Psys(W)
Max
3
4
8
10
15
25
70 C Case
Static Gain
Flatness
Dynamic Gain
Flatness
Output Power
Stability
Power
Consumption
(Steady state)
o
Notes:
1. Unless stated otherwise, all specifications apply over the full operating temperature and humidity ranges
2. Measurement variations
3. Measured with 8 evenly spread input optical signals @ 25°C, Pin ≈ 0 dBm. Measuring with 1 input optical signal with Pin
≈ 0 dBm and  ≈ 1550 nm is also available (Low Noise Figure options with NF <4.0/4.5 dB are available for some models
only)
4. Measured with a swept Probe Signal (Pp), where Pp ≈ 0 dBm @ 25C
5. Measured with a swept Probe Signal (Pp), and a fixed Tone Signal (Pt) @ ~ 1550 nm; (Pt ≈ Pp+20 dB; Pt + Pp ≈ 0 dBm)
@ 25C; Gain Flattened Options with ΔG ≤ +/-0.75dB or ΔG ≤ +/-1.0dB are available (for some models only)
6. Over polarization and temperature
7. Static and Dynamic Gain Flatness for PONA 2130 can be defined for 1545 nm ≤  ≤ 1562 nm and by special request
only.
8. Specific NF and ΔG can be guaranteed at a single specified Input Optical Power Level (Pin = Pt + Pp) equal or different
from 0 dBm.
General and Mechanical Specifications
Requirement
Comments
Operating Wavelength
Property
1530 nm ~ 1562 nm
Standard
Operating Case Temperature
-20C to 75C
Storage Temperature
-40C to 85C
Operating Humidity
20% to 85%
Non-condensing
+4.5V to +5.5VDC
All versions
Voltage Supply Range
Optical Connectors
Dimensions (in)
SC/APC; SC/UPC; FC/APC;
FC/UPC; E2000/APC
4.9”W x 5.9”D x 0.8”H
4.9”W x 5.9”D x 1.9”H
User Specified
MAFA 2014 to MAFA 2023
MAFA 2024 to MAFA 2027
* With a 1” heat sink. (MAFA 2024 and MAFA 2027 require a heat sink to meet operating temperature specifications)
| REV 2012.08
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
MAFA 2000 Series EDFA
FIBER OPTICS
DATASHEET | AUGUST 2012
Outline Drawing
Electrical Connector Pinout
PIN #
Designation
PIN #
Designation
1
DC Power Input (+5V)
16
Reserved
2
GND
17
Reserved
3
Reserved
18
RS-232 Rx*
4
Reserved
19
Reserved
5
KEY-SWITCH
20
Reserved
6
RS-232Tx
21
Reserved
7
Reserved
22
Reserved
8
Reserved
23
Reserved B
9
Reserved
24
N/A
10
Reserved
25
Reserved
11
Reserved
12
Reserved
13
Reserved
14
DC Power Input (+5V)
15
GND
| REV 2012.08
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
MAFA 2000 Series EDFA
FIBER OPTICS
DATASHEET | AUGUST 2012
Compliance and Reliability Information
FCC: Subpart B. Part 15 class “A”: Unintentional Radiators
EN 55013: Sound and Television Broadcast receivers and associated equipment – Radio disturbance characteristics- limits
and methods of measurements – Electric Field Radiation Emissions (2001)
Fit Rate: 60% level of confidence 670 @ 25C (14-23 dBm EDFA)
Fit Rate: 60% of level of confidence 962 @ 40C (24-27 dBm EDFA)
Note: It has been determined that recent design changes with the DB25 connector make necessary the re-certification of the MAFA2000 for
Electromagnetic Compatibility (EMC) per EN 61000-4-3. Prior to this certification, it is possible that if the MAFA2000 is exposed to electromagnetic
interference (EMI) it may cause unintended changes in the behavior of the unit. In addition to possible improper operation, there are safety implications to
consider as well. It is recommended that users of this product do so for evaluation purposes only, and exercise caution. At a minimum, it is recommended
that a metallic shielded cable be used to connect to the DB25 connector to minimize risk. Other methods of reducing potential EMI such as testing unit far
away from electromagnetic radiators, and in a metallic enclosure (such as the PONA2100 series) is highly recommended. Users of this product do so at
their own risk.
Ordering Information
MAFA20
-
-
Power Level
Connector Option
GF/NF Options
14 – 14 dBm
SC - SC/APC
00 - Standard
17 – 17 dBm
FC - FC/APC
01 – Standard with Gain Flattened Option
20 – 20 dBm
FC – FC/APC
01 – Standard with Gain Flattened Option
23 – 23 dBm
EC – E2000/APC Diamond
02 – Standard with Low NF Option
24 – 24 dBm
TC – SC/UPC
03 – Gain Flattened and Low NF Option
27 – 27 dBm
GC – FC/UPC
Example:
MAFA2017-SC-00: Standard 17 dBm gain block with SC/APC optical connectors
Note:
Only some models can be order with Gain Flattened options and/or Low NF options (-01, -02, and -03 suffixes).
| REV 2012.08
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
Similar pages