Maxim MAX1683EUKT Switched-capacitor voltage doubler Datasheet

19-1305; Rev 3; 11/10
Switched-Capacitor Voltage Doublers
____________________________Features
The ultra-small MAX1682/MAX1683 monolithic, CMOS
charge-pump voltage doublers accept input voltages
ranging from +2.0V to +5.5V. Their high voltage-conversion efficiency (over 98%) and low operating current
(110µA for MAX1682) make these devices ideal for
both battery-powered and board-level voltage-doubler
applications.
♦ 5-Pin SOT23 Package
Oscillator control circuitry and four power MOSFET
switches are included on-chip. The MAX1682 operates
at 12kHz, and the MAX1683 operates at 35kHz. A typical application includes generating a 6V supply to
power an LCD display in a hand-held PDA. Both parts
are available in a 5-pin SOT23 package and can deliver
30mA with a typical voltage drop of 600mV.
♦ Up to 45mA Output Current
♦ +2.0V to +5.5V Input Voltage Range
♦ 98% Voltage-Conversion Efficiency
♦ 110µA Quiescent Current (MAX1682)
♦ Requires Only Two Capacitors
Ordering Information
________________________Applications
Small LCD Panels
PART
Cell Phones
TEMP
RANGE
PINPACKAGE
SOT
TOP MARK
MAX1682EUK+T -40°C to +85°C 5 SOT23-5
ACCL
MAX1683EUK+T -40°C to +85°C 5 SOT23-5
ACCM
Note: These parts are available in tape-and-reel only. Minimum
order quantity is 2500 pieces.
+Denotes a lead(Pb)-free/RoHS-compliant package.
T = Tape and reel.
Handy-Terminals
PDAs
Typical Operating Circuit
5
IN
C1+
4
INPUT
SUPPLY
VOLTAGE
VIN
Pin Configuration
C1
MAX1682
MAX1683
3
TOP VIEW
C1GND 1
OUT
1
OUTPUT
VOLTAGE
2 x VIN
2
OUT 2
5
C1+
4
IN
MAX1682
MAX1683
C2
GND
C1- 3
VOLTAGE DOUBLER
SOT23-5
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
1
MAX1682/MAX1683
General Description
MAX1682/MAX1683
Switched-Capacitor Voltage Doublers
ABSOLUTE MAXIMUM RATINGS
IN to GND .................................................................+6V to -0.3V
OUT to GND .......................................................+12V, VIN - 0.3V
OUT Output Current............................................................50mA
Output Short-Circuit Duration .................................1sec (Note 1)
Continuous Power Dissipation (TA = +70°C)
SOT23-5 (derate 7.1mW/°C above +70°C)...................571mW
Operating Temperature Range
MAX1682EUK/MAX1683EUK ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +160°C
Lead Temperature (soldering, 10sec) .............................+300°C
Soldering Temperature (reflow) .......................................+260°C
Note 1: Avoid shorting OUT to GND, as it may damage the device. For temperatures above +85°C, shorting OUT to GND even
instantaneously will damage the device.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VIN = +5.0V, capacitor values from Table 2, TA = 0°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
CONDITIONS
No-Load Supply Current
TA = +25°C
Supply Voltage Range
RLOAD = 10kΩ
Minimum Operating Voltage
(Note 2)
TYP
MAX
MAX1682
MIN
110
145
MAX1683
230
310
TA = +25°C
2.0
1.7
5.5
TA = 0°C to +85°C
2.1
1.8
5.5
MAX1682
8.4
12
15.6
MAX1683
24.5
35
45.5
1
Oscillator Frequency
TA = +25°C
Output Resistance
IOUT = 5mA
Voltage Conversion Efficiency
IOUT = 0mA, TA = +25°C
TA = +25°C
20
TA = 0°C to +85°C
µA
V
V
50
65
98
UNITS
99.9
kHz
Ω
%
Note 2: Once started, the MAX1682/MAX1683 typically operate down to 1V.
ELECTRICAL CHARACTERISTICS
(VIN = +5.0V, capacitor values from Table 2, TA = -40°C to +85°C, unless otherwise noted.) (Note 3)
PARAMETER
No-Load Supply Current
Supply Voltage Range
Oscillator Frequency
CONDITIONS
MIN
TYP
160
MAX1683
350
RLOAD = 10kΩ
2.3
5.5
MAX1682
6.6
18.6
MAX1683
17.5
57.8
Output Resistance
IOUT = 5mA
Voltage Conversion Efficiency
IOUT = 0mA
65
97
Note 3: Specifications at -40°C to +85°C are guaranteed by design.
2
MAX
MAX1682
_______________________________________________________________________________________
UNITS
µA
V
kHz
Ω
%
Switched-Capacitor Voltage Doublers
MAX1682, C1 = C2 = 10μF
40
30
30
VIN = 3.3V
25
20
15
VIN = 5V
10
20
5
-40
-20
MAX1682 OUTPUT RESISTANCE
vs. CAPACITANCE
VIN = 2V
40
20
40
5
10
15
25
-40
80
0
MAX1682/83 TOC05
30
25
VIN = 3.3V
20
15
600
80
C1 = C2 = 3.3μF
500
400
300
C1 = C2 = 10μF
200
VIN = 5V
C1 = C2 = 33μF
100
0
0
35
0
5
10
15
20
25
30
35
0
5
10
15
20
25
30
35
40
IOUT (mA)
MAX1683
OUTPUT VOLTAGE RIPPLE
vs. OUTPUT CURRENT
SUPPLY CURRENT
vs. SUPPLY VOLTAGE
900
C1 = C2 =1μF
700
600
500
C1 = C2 = 3.3μF
300
C1 = C2 = 10μF
300
250
SUPPLY CURRENT (μA)
MAX1682/83 TOC07
1000
200
60
700
CAPACITANCE (μF)
400
40
800
VIN = 2V
35
CAPACITANCE (μF)
800
20
MAX1682
OUTPUT VOLTAGE RIPPLE
vs. OUTPUT CURRENT
5
30
-20
MAX1683 OUTPUT RESISTANCE
vs. CAPITANCE
40
VIN = 3.3V
20
VIN = 5V
10
MAX1682/83 TOC09
VIN = 5V
0
15
TEMPERATURE (°C)
10
0
60
45
20
20
ILOAD = 5mA
VRIPPLE (mV)
60
0
50
OUTPUT RESISTANCE (Ω)
MAX1682/83 TOC4
80
VRIPPLE (mV)
OUTPUT RESISTANCE (Ω)
100
VIN = 3.3V
25
TEMPERATURE (°C)
VIN (V)
120
30
0
0
1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
VIN = 2V
5
ILOAD = 5mA
MAX1683, C1 = C2 = 10μF
10
35
MAX1682/83 TOC06
50
VIN = 2V
40
OUTPUT RESISTANCE (Ω)
MAX1683, C1 = C2 = 3.3μF
60
35
MAX1682/83 TOC02
MAX1682/83 TOC1
OUTPUT RESISTANCE (Ω)
80
40
OUTPUT RESISTANCE (Ω)
90
70
MAX1683 OUTPUT RESISTANCE
vs. TEMPERATURE
MAX1682 OUTPUT RESISTANCE
vs. TEMPERATURE
MAX1682/83 TOC03
OUTPUT RESISTANCE
vs. SUPPLY VOLTAGE
200
MAX1683
150
100
50
100
MAX1682
0
0
0
5
10
15
20
IOUT (mA)
25
30
35
40
1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
SUPPLY VOLTAGE (V)
_______________________________________________________________________________________
3
MAX1682/MAX1683
Typical Operating Characteristics
(Typical Operating Circuit, VIN = +5V, C1 = C2 = 10µF for the MAX1682 and 3.3µF for the MAX1683, TA = +25°C, unless otherwise
noted.)
Typical Operating Characteristics (continued)
(Typical Operating Circuit, VIN = +5V, C1 = C2 = 10µF for the MAX1682 and 3.3µF for the MAX1683, TA = +25°C, unless otherwise
noted.)
12.0
VIN = 3.3V
11.5
VIN = 2V
MAX1682/83 TOC11
38
VIN = 5V
36
34
32
VIN = 3.3V
10
9
VIN = 5V
8
OUTPUT VOLTAGE (V)
VIN = 5V
40
OSCILLATOR FREQUENCY (kHz)
MAX1682/83 TOC10
OSCILLATOR FREQUENCY (kHz)
12.5
MAX1682 OUTPUT VOLTAGE
vs. OUTPUT CURRENT
MAX1683 OSCILLATOR FREQUENCY
vs. TEMPERATURE
VIN = 2V
7
MAX1682/83 TOC12
MAX1682 OSCILLATOR FREQUENCY
vs. TEMPERATURE
VIN = 3.3V
6
5
VIN = 2V
4
3
2
30
1
0
28
-20
0
20
40
60
80
-20
0
20
40
60
0
80
OUTPUT CURRENT (mA)
MAX1683 OUTPUT VOLTAGE
vs. OUTPUT CURRENT
MAX1682 EFFICIENCY vs.
LOAD CURRENT
MAX1683 EFFICIENCY vs.
LOAD CURRENT
VIN = 3.3V
5
VIN = 2V
VIN = 5V
96
94
92
VIN = 2V
90
100
MAX1682/83 TOC14
98
EFFICIENCY (%)
7
6
100
98
VIN = 3.3V
88
94
92
VIN = 2V
90
VIN = 3.3V
88
3
86
86
2
84
84
1
82
82
0
80
10 15 20 25 30 35 40 45 50
VIN = 5V
96
EFFICIENCY (%)
VIN = 5V
8
80
0
5
10
15
20
25
0
30
5
10
15
20
OUTPUT CURRENT (mA)
LOAD CURRENT (mA)
LOAD CURRENT (mA)
MAX1682
OUTPUT RIPPLE
MAX1683
OUTPUT RIPPLE
START-UP VOLTAGE
vs. RESISTIVE LOAD
30
MAX1682toc18
MAX1682toc17
VOUT
20mV/div
VOUT
20mV/div
25
2.5
MAX1683
2.0
VSTART (V)
MAX1682toc16
5
10 15 20 25 30 35 40 45 50
TEMPERATURE (°C)
9
0
5
TEMPERATURE (°C)
10
4
-40
MAX1682/83 TOC13
-40
MAX1682/83 TOC15
11.0
OUTPUT VOLTAGE (V)
MAX1682/MAX1683
Switched-Capacitor Voltage Doublers
1.5
1.0
MAX1682
0.5
0
20μs/div
ILOAD = 5mA, VIN = 5V, C1 = C2 = 10μF
4
20μs/div
ILOAD = 5mA, VIN = 5V, C1 = 3.3μF, C2 = 10μF
700 300 100 70 30 10
7
RLOAD (kΩ)
_______________________________________________________________________________________
3
1
0.7 0.3
Switched-Capacitor Voltage Doublers
PIN
NAME
FUNCTION
1
GND
Ground
2
OUT
Doubled Output Voltage. Connect C2
between OUT and GND.
3
C1-
Negative Terminal of the Flying
Capacitor
4
IN
5
C1+
Efficiency Considerations
The power efficiency of a switched-capacitor voltage
converter is affected by three factors: the internal losses
in the converter IC, the resistive losses of the capacitors,
and the conversion losses during charge transfer
between the capacitors. The total power loss is:
ΣPLOSS = PINTERNAL LOSSES
+ PPUMP CAPACITOR LOSSES
+ PCONVERSION LOSSES
Input Supply
Positive Terminal of the Flying
Capacitor
_______________Detailed Description
The MAX1682/MAX1683 capacitive charge pumps
double the voltage applied to their input. Figure 1
shows a simplified functional diagram of an ideal voltage doubler. During the first half-cycle, switches S1
and S2 close, and capacitor C1 charges to VIN. During
the second half cycle, S1 and S2 open, S3 and S4
close, and C1 is level shifted upward by VIN volts. This
connects C1 to the reservoir capacitor C2, allowing
energy to be delivered to the output as necessary. The
actual voltage is slightly lower than 2 x V IN , since
switches S1–S4 have resistance and the load drains
charge from C2.
Charge-Pump Output
The MAX1682/MAX1683 have a finite output resistance
of about 20Ω (Table 2). As the load current increases,
the devices’ output voltage (VOUT) droops. The droop
equals the current drawn from VOUT times the circuit’s
output impedance (RS), as follows:
VDROOP = IOUT x RS
VOUT = 2 x VIN - VDROOP
The internal losses are associated with the IC’s internal
functions, such as driving the switches, oscillator, etc.
These losses are affected by operating conditions such
as input voltage, temperature, and frequency.
The next two losses are associated with the voltage
converter circuit’s output resistance. Switch losses
occur because of the on-resistance of the MOSFET
switches in the IC. Charge-pump capacitor losses
occur because of their ESR. The relationship between
these losses and the output resistance is as follows:
PPUMP CAPACITOR LOSSES + PSWITCH LOSSES =
IOUT
2
x ROUT
1
+ 2RSWITCHES + 4ESRC1
fOSC x C1
ROUT ≅
(
)
+ ESRC2
where fOSC is the oscillator frequency. The first term is
the effective resistance from an ideal switchedcapacitor circuit (Figures 2a and 2b).
f
V+
VOUT
C2
RL
C1
S1
S3
VIN
Figure 2a. Switched-Capacitor Model
C1
VOUT
C2
S2
S4
REQUIV
V+
VOUT
1
REQUIV =
f × C1
C2
RL
VIN
Figure 1. Simplified Functional Diagram of Ideal Voltage
Doubler
Figure 2b. Equivalent Circuit
_______________________________________________________________________________________
5
MAX1682/MAX1683
_____________________Pin Description
MAX1682/MAX1683
Switched-Capacitor Voltage Doublers
Conversion losses occur during the charge transfer
between C1 and C2 when there is a voltage difference
between them. The power loss is:
⎡
⎛
2
2⎞
PCONVERSION LOSS = ⎢1/ 2C1 ⎜ 4VIN − VOUT ⎟ +
⎢
⎝
⎠
⎣
⎛
⎞⎤
2
1/ 2C2 ⎜ 2VOUT VRIPPLE − V RIPPLE ⎟ ⎥ x fOSC
⎝
⎠⎦
where VRIPPLE is the peak-to-peak output voltage ripple
determined by the output capacitor and load current
(see Output Capacitor section). Choose capacitor values that decrease the output resistance (see Flying
Capacitor section).
Applications Information
Flying Capacitor (C1)
To maintain the lowest output resistance, use capacitors with low ESR. Suitable capacitor manufacturers are
listed in Table 1. The charge-pump output resistance is
a function of C1 and C2’s ESR and the internal switch
resistance, as shown in the equation for ROUT in the
Efficiency Considerations section.
Minimizing the charge-pump capacitor’s ESR minimizes the total resistance. Suggested values are listed
in Tables 2 and 3.
Using a larger flying capacitor reduces the output
impedance and improves efficiency (see the Efficiency
Considerations section). Above a certain point, increasing C1’s capacitance has a negligible effect because
the output resistance becomes dominated by the internal switch resistance and capacitor ESR (see the
Output Resistance vs. Capacitance graph in the
Typical Operating Characteristics). Table 2 lists the
most desirable capacitor values—those that produce a
low output resistance. But when space is a constraint, it
may be necessary to sacrifice low output resistance for
the sake of small capacitor size. Table 3 demonstrates
how the capacitor affects output resistance.
Output Capacitor (C2)
Increasing the output capacitance reduces the output
ripple voltage. Decreasing its ESR reduces both output
resistance and ripple. Smaller capacitance values can
be used with light loads. Use the following equation to
calculate the peak-to-peak ripple:
VRIPPLE = IOUT / (fOSC x C2) + 2 x IOUT x ESRC2
Input Bypass Capacitor
Bypass the incoming supply to reduce its AC impedance and the impact of the MAX1682/MAX1683’s
switching noise. When loaded, the circuit draws a continuous current of 2 x IOUT. A 0.1µF bypass capacitor is
sufficient.
Table 1. Recommended Capacitor Manufacturers
PRODUCTION METHOD
MANUFACTURER
SERIES
PHONE
FAX
AVX
TPS
803-946-0690
803-448-2170
Surface-Mount Tantalum
Surface-Mount Ceramic
Matsuo
267
714-969-2491
714-960-6492
Sprague
593D, 595D
603-224-1961
603-224-1430
AVX
X7R
803-946-0590
803-626-3123
Matsuo
X7R
714-969-2491
714-960-6492
Table 2. Suggested Capacitor Values for
Low Output Resistance
6
Table 3. Suggested Capacitor Values for
Minimum Size
PART
FREQUENCY
(kHz)
CAPACITOR
VALUE (µF)
TYPICAL
ROUT (Ω)
PART
FREQUENCY
(kHz)
CAPACITOR
VALUE (µF)
TYPICAL
ROUT (Ω)
MAX1682
12
10
20
MAX1682
12
3.3
35
MAX1683
35
3.3
20
MAX1683
35
1
35
_______________________________________________________________________________________
Switched-Capacitor Voltage Doublers
Paralleling Devices
Paralleling multiple MAX1682 or MAX1683s reduces
the output resistance. Each device requires its own
pump capacitor (C1), but the reservoir capacitor (C2)
serves all devices (Figure 4). Increase C2’s value by a
factor of n, where n is the number of parallel devices.
Figure 4 shows the equation for calculating output
resistance.
Layout and Grounding
Good layout is important, primarily for good noise performance. To ensure good layout, mount all components as close together as possible, keep traces short
to minimize parasitic inductance and capacitance, and
use a ground plane.
INPUT
SUPPLY
VOLTAGE
INPUT
SUPPLY
VOLTAGE
C1+
IN
MAX1682
MAX1683
C1
IN
C1+
C1+
MAX1682
GND
C1
OUTPUT
VOLTAGE
C1
GND
C1
GND
OUT
MAX1682
MAX1683
OUTPUT
VOLTAGE
OUT
C1-
C1-
IN
C1+
MAX1682
MAX1683
GND MAX1683
C1-
IN
C2
C1-
OUT
OUT
C2
R
OF SINGLE DEVICE
ROUT = OUT
NUMBER OF DEVICES
Figure 3. Cascading Devices
C2
Figure 4. Paralleling Devices
_______________________________________________________________________________________
7
MAX1682/MAX1683
Cascading Devices
Devices can be cascaded to produce an even larger
voltage (Figure 3). The unloaded output voltage is nominally (n + 1) x VIN, where n is the number of voltage
doublers used. This voltage is reduced by the output
resistance of the first device multiplied by the quiescent
current of the second. The output resistance increases
when devices are cascaded. Using a two-stage doubler as an example, output resistance can be approximated as ROUT = 2 x ROUT1 + ROUT2, where ROUT1 is
the output resistance of the first stage and ROUT2 is the
output resistance of the second stage. A typical value
for a two-stage voltage doubler is 60Ω (with C1 at 10µF
for MAX1682 and 3.3µF for MAX1683). For n stages
with the same C1 value, ROUT = (2n - 1) x ROUT1.
Package Information
For the latest package outline information and land patterns, go to www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in the
package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the
package regardless of RoHS status.
PACKAGE TYPE
PACKAGE CODE
OUTLINE NO.
LAND PATTERN NO.
5 SOT23
U5+2
21-0057
90-0174
SOT-23 5L .EPS
MAX1682/MAX1683
Switched-Capacitor Voltage Doublers
8
_______________________________________________________________________________________
Switched-Capacitor Voltage Doublers
Revision History
REVISION
NUMBER
REVISION
DATE
3
11/10
DESCRIPTION
Added lead-free parts
PAGES
CHANGED
1
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
9 _____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2010 Maxim Integrated Products
Maxim is a registered trademark of Maxim Integrated Products.
Similar pages