MAXIM MAX16903_13

EVALUATION KIT AVAILABLE
MAX16903
2.1MHz, High-Voltage, 1A Mini-Buck Converter
General Description
The MAX16903 is a small, synchronous buck converter
with integrated high-side and low-side switches. The
device is designed to deliver 1A with input voltages
from +3.5V to +28V while using only 25μA quiescent
current at no load. Voltage quality can be monitored by
observing the PGOOD signal. The MAX16903 can operate in dropout by running at 97% duty cycle, making it
ideal for automotive and industrial applications.
The MAX16903 operates at a 2.1MHz frequency, allowing for small external components and reduced output
ripple. It guarantees no AM band interference. SYNC
input programmability enables three frequency modes
for optimized performance: forced fixed-frequency
operation, skip mode (ultra-low quiescent current of
25μA), and synchronization to an external clock. The
MAX16903 can be ordered with spread-spectrum frequency modulation, designed to minimize EMI-radiated
emissions due to the modulation frequency.
The MAX16903 is available in a thermally enhanced,
3mm x 3mm, 10-pin TDFN package or a 16-pin TSSOP
package. The MAX16903 operates over the -40°C to
+125°C automotive temperature range.
Applications
Features
o Wide +3.5V to +28V Input Voltage Range
o Tolerates Input Voltage Transients to +42V
o 1A Minimum Output Current with Overcurrent
Protection
o Fixed Output Voltages (see the Selector Guide
and contact the factory for all available trimmed
output voltage options)
o 2.1MHz Switching Frequency with 3 Modes of
Operation
25µA Ultra-Low Quiescent Current Skip Mode
Forced Fixed-Frequency Operation
External Frequency Synchronization
o Optional Spread-Spectrum Frequency Modulation
o Power-Good Output
o Enable-Pin Compatible from +3.3V Logic Level to
+42V
o Thermal Shutdown Protection
o -40°C to +125°C Automotive Temperature Range
o 10-Pin TDFN-EP or 16-Pin TSSOP-EP Packages
o AEC-Q100 Qualified
Automotive
Ordering Information
Industrial
Military
PART
TEMP
SPREAD
SPECTRUM RANGE
High-Voltage Input-Power DC-DC Applications
PINPACKAGE
MAX16903RAUE__/V+
Disabled
-40°C to
+125°C
16 TSSOP-EP*
MAX16903RATB__/V+
Disabled
-40°C to
+125°C
10 TDFN-EP*
MAX16903SAUE__/V+
Enabled
-40°C to
+125°C
16 TSSOP-EP*
MAX16903SATB__/V+
Enabled
-40°C to
+125°C
10 TDFN-EP*
Note: Insert the desired suffix letters (from Selector Guide) into
the blanks to indicate the output voltage. Alternative output voltages available upon request.
+Denotes a lead(Pb)-free/RoHS-compliant package.
/V denotes an automotive qualified part.
*EP = Exposed pad.
For pricing, delivery, and ordering information, please contact Maxim Direct
at 1-888-629-4642, or visit Maxim’s website at www.maximintegrated.com.
19-5038; Rev 4; 4/13
MAX16903
2.1MHz, High-Voltage, 1A Mini-Buck Converter
Typical Operating Circuits
33kΩ
SUP
4.7μF
VBAT LEVEL
SIGNAL
EN
*
MAX16903_50/V+
SYNC
BST
GND
0.1μF
4.7μH
5V AT 1A
PGOOD
LX
10μF
20kΩ
PGND
BIAS
OUTS
2.2μF
33kΩ
SUP
4.7μF
VBAT LEVEL
SIGNAL
EN
*
MAX16903_33/V+
SYNC
BST
GND
0.1μF
3.3μH
3.3V AT 1A
LX
PGOOD
10μF
20kΩ
PGND
OUTS
BIAS
2.2μF
*PLACE INPUT SUPPLY CAPACITORS AS CLOSE AS POSSIBLE TO THE SUP PIN. SEE THE APPLICATIONS INFORMATION SECTION FOR MORE DETAILS.
2
Maxim Integrated
MAX16903
2.1MHz, High-Voltage, 1A Mini-Buck Converter
ABSOLUTE MAXIMUM RATINGS
(Voltages referenced to GND.)
SUP, EN..................................................................-0.3V to +42V
BST to LX..................................................................-0.3V to +6V
LX..............................................................-0.3V to (VSUP + 0.3V)
BST .........................................................................-0.3V to +47V
OUTS ......................................................................-0.3V to +12V
SYNC, PGOOD, BIAS............................................-0.3V to +6.0V
PGND to GND .......................................................-0.3V to +0.3V
LX Continuous RMS Current .................................................1.5A
OUTS Short-Circuit Duration ......................................Continuous
ESD Protection
Human Body Model .........................................................±2kV
Machine Model ..............................................................±200V
Continuous Power Dissipation (TA = +70°C)
TDFN (derate 24.4 mW/°C above +70°C)......................1951mW
TSSOP (derate 26.1 mW/°C above +70°C) ...................2089mW
Operating Temperature Range .........................-40°C to +125°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Soldering Temperature (reflow) .......................................+260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
PACKAGE THERMAL CHARACTERISTICS (Note 1)
TDFN
Junction-to-Ambient Thermal Resistance (θJA) ...........41°C/W
Junction-to-Case Thermal Resistance (θJC) ..................9°C/W
TSSOP
Junction-to-Ambient Thermal Resistance (θJA) ........38.3°C/W
Junction-to-Case Thermal Resistance (θJC) ..................3°C/W
Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer
board. For detailed information on package thermal considerations, refer to www.maximintegrated.com/thermal-tutorial.
ELECTRICAL CHARACTERISTICS
(VSUP = +14V, TA = TJ = -40°C to +125°C, unless otherwise noted. Typical values are at TA = +25°C, unless otherwise noted.)
PARAMETER
SYMBOL
Supply Voltage Range
VSUP
Supply Current
I SUP
CONDITIONS
MIN
(Note 2)
UV Lockout
42
EN = low
4
8
EN = high, no load
25
35
Bias rising
1
2.8
VUVLO,HYS Hysteresis
Bias Voltage
VBIAS
Bias Current Limit
IBIAS
MAX
28
t < 1s
EN = high, continuous, no switching
VUVLO
TYP
3.5
3
V
µA
mA
3.2
0.4
+5.5V VSUP +42V
UNITS
5
V
V
10
mA
BUCK CONVERTER
VOUT,5V
Voltage Accuracy
VOUT,3.3V
VOUT,5V
VOUT,3.3V
Maxim Integrated
VOUT = 5V, fixed frequency
VOUT = 5V, SKIP mode (Note 3)
VOUT = 3.3V, fixed frequency
VOUT = 3.3V, SKIP mode (Note 3)
VOUT = 5V, fixed frequency
VOUT = 5V, SKIP mode (Note 3)
VOUT = 3.3V, fixed frequency
VOUT = 3.3V, SKIP mode (Note 3)
6V VSUP 18V,
ILOAD = 0 to 1A,
TA = 0°C to
+125°C
6V VSUP 18V,
ILOAD = 0 to 1A,
TA = -40°C to
+125°C
-2.0%
5
+2.5%
-2.0%
5
+4%
+2.5%
-2.0%
3.3
-2.0%
3.3
+4%
-3.0%
-3.0%
5
+2.5%
5
+4%
-3.0%
3.3
+2.5%
-3.0%
3.3
+4%
V
3
MAX16903
2.1MHz, High-Voltage, 1A Mini-Buck Converter
ELECTRICAL CHARACTERISTICS (continued)
(VSUP = +14V, TA = TJ = -40°C to +125°C, unless otherwise noted. Typical values are at TA = +25°C, unless otherwise noted.)
PARAMETER
SYMBOL
Skip-Mode Peak Current
I SKIP
High-Side DMOS RDSON
R ON,HS
Low-Side DMOS RDSON
R ON,LS
DMOS Peak Current-Limit
Threshold
Soft-Start Ramp Time
LX Rise Time
CONDITIONS
MIN
TYP
MAX
UNITS
400
800
m
250
450
m
350
VBIAS = 5V
IMAX
1.275
1.5
1.75
A
t SS
7
8
9
ms
tRISE,LX
5
Minimum On-Time
t ON
80
PWM Switching Frequency
f SW
SYNC Input Frequency Range
Spread-Spectrum Range
mA
Internally generated
f SYNC
SS
1.925
2.1
1.8
Spread-spectrum option only
ns
ns
2.275
MHz
2.6
MHz
+6
%
PGOOD
PGOOD Threshold
PGOOD Debounce
VTHR,PGD
VOUT rising
VTHF,PGD
VOUT falling
93
88
tDEB
91
94
10
%
µs
PGOOD HIGH Leakage Current
ILEAK,PGD
TA = +25°C
1
µA
PGOOD Output Low Level
VOUT,PGD
Sinking 1mA
0.4
V
LOGIC LEVELS
EN Level
EN Input Current
SYNC Switching Threshold
SYNC Internal Pulldown
VIH,EN
2.4
0.6
VIL,EN
I IN,EN
VEN = V SUP = +42V, TA = +25°C
VIH,SYNC
1
1.4
0.4
VIL,SYNC
V
µA
V
RPD,SYNC
200
k
T SHDN
175
°C
T SHDN,HYS
15
°C
THERMAL PROTECTION
Thermal Shutdown
Thermal Shutdown Hysteresis
Note 2: When the typical minimum on-time of 80ns is violated, the device skips pulses.
Note 3: Guaranteed by design; not production tested.
4
Maxim Integrated
MAX16903
2.1MHz, High-Voltage, 1A Mini-Buck Converter
Typical Operating Characteristics
(VSUP = +14V, TA = +25°C, unless otherwise noted.)
EFFICIENCY vs. LOAD CURRENT
(5V VERSION)
FFF MODE
60
50
40
30
20
40
5V PART
30
20
3.3V PART
10
0
0.001
0.01
0.1
MAX16903 toc03
0
-1
-2
8 10 12 14 16 18 20 22 24 26 28
6
8 10 12 14 16 18 20 22 24 26 28
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
LOAD REGULATION
SHUTDOWN SUPPLY CURRENT
vs. INPUT VOLTAGE
STARTUP WAVEFORM (ILOAD = 1A)
SKIP MODE
12
SUPPLY CURRENT (µA)
1
0
FFF MODE
-2
MAX16903 toc06
MAX16903 toc05
15
MAX16903 toc04
OUTPUT-VOLTAGE CHANGE (%)
1
-4
6
2
-1
2
ILOAD (A)
4
3
1
3
-3
10
0
0.00001 0.0001
4
OUTPUT-VOLTAGE CHANGE (%)
EFFICIENCY (%)
70
50
SUPPLY CURRENT (µA)
SKIP MODE
80
60
MAX16903 toc02
90
MAX16903 toc01
100
LINE REGULATION
(ILOAD = 1A)
NO-LOAD SUPPLY CURRENT
vs. INPUT VOLTAGE (SKIP MODE)
EN
5V/div
IINDUCTOR
1A/div
9
6
PGOOD
5V/div
3
-3
-4
0
0.2
0.4
0.6
0.8
1.0
VOUT
5V/div
0
6
LOAD CURRENT (A)
1ms/div
8 10 12 14 16 18 20 22 24 26 28
INPUT VOLTAGE (V)
LOAD-TRANSIENT RESPONSE
(FIXED MODE)
SHUTDOWN WAVEFORM (ILOAD = 1A)
MAX16903 toc08
MAX16903 toc07
ILOAD
1A/div
EN
5V/div
IINDUCTOR
1A/div
PGOOD
5V/div
VOUT
5V/div
20µs/div
Maxim Integrated
VOUT
200mV/div
AC
COUPLED
5V
PGOOD
5V/div
5V
ILOAD = 100mA TO 1A TO 100mA
200µs/div
5
MAX16903
2.1MHz, High-Voltage, 1A Mini-Buck Converter
Typical Operating Characteristics (continued)
(VSUP = +14V, TA = +25°C, unless otherwise noted.)
LOAD-TRANSIENT RESPONSE
(SKIP MODE)
STANDBY CURRENT
vs. LOAD CURRENT
UNDERVOLTAGE PULSE (COLD CRANK)
MAX16903 toc10
14V
3.5V
VOUT
5V/div
250
150
100
ILOAD = 500mA
ILOAD
1A/div
ILOAD = 100mA TO 1A TO 100mA
50
0
10ms/div
200µs/div
300
200
PGOOD
5V/div
PGOOD
5V/div
5V
400
350
VOUT
200mV/div
ACCOUPLED
5V
450
VSUP
10V/div
ISUP (µA)
ILOAD
1A/div
500
MAX16903 toc11
MAX16903 toc09
0.01
1.00
0.10
ILOAD (mA)
Pin Configurations
TOP VIEW
BST
1
SUP
+
10
EN
2
9
GND
LX
3
8
BIAS
PGND
4
7
SYNC
OUTS
5
6
PGOOD
MAX16903
EP
+
BST
1
16 N.C.
SUP
2
15 EN
SUP
3
14 GND
LX
4
LX
5
12 SYNC
PGND
6
11 PGOOD
PGND
7
10 N.C.
OUTS
8
MAX16903
13 BIAS
EP
9
N.C.
TDFN
TSSOP
Pin Description
PIN
6
TDFN
TSSOP
1
1
NAME
FUNCTION
BST
Bootstrap Capacitor for High-Side Driver (0.1μF)
Voltage Supply Input. Connect a 4.7μF ceramic capacitor from SUP to PGND. Place the
capacitor very close to the SUP pin. For the TSSOP-EP package, connect both SUP pins
together for proper operation.
2
2, 3
SUP
3
4, 5
LX
4
6, 7
PGND
Buck Switching Node. LX is high impedance when the device is off. For the TSSOP package,
connect both LX pins together for proper operation.
Power Ground. For the TSSOP-EP package, connect both PGND pins together for proper
operation.
Maxim Integrated
MAX16903
2.1MHz, High-Voltage, 1A Mini-Buck Converter
Pin Description (continued)
PIN
NAME
TDFN
TSSOP
5
8
OUTS
6
11
PGOOD
7
FUNCTION
Buck Regulator Voltage-Sense Input. Bypass OUTS to PGND with a 10µF or larger X7R
ceramic capacitor.
Open-Drain Power-Good Output
Sync Input. SYNC allows the device to synchronize to other supplies. When connected to
GND or unconnected, skip mode is enabled under light loads. When connected to a clock
source or BIAS, forced PWM mode is enabled.
12
SYNC
8
13
BIAS
+5V Internal Logic Supply. Connect a 2.2µF ceramic capacitor from BIAS to GND.
9
14
GND
Analog Ground
10
15
EN
9, 10, 16
N.C.
EP
Enable Input. EN is high-voltage compatible. Drive EN HIGH for normal operation.
No Connection. Not internally connected.
Exposed Pad. Connect EP to PGND. Do not use EP as the only ground connection.
Functional Diagram
SYNC
REF
EN
HVLDO
BANDGAP
OSC
BST
BIAS
SUP
CLK
HSD
SOFT-START
CURRENT-SENSE
AND
SLOPE COMPENSATION
LOGIC
CONTROL
LX
BIAS
OUTS
PWM
LSD
EAMP
COMP
MAX16903
VGOOD
PGND
PGOOD
Detailed Description
The MAX16903 is a small, current-mode buck converter
that features synchronous rectification and requires no
external compensation network. The MAX16903 is
designed for 1A output current. The MAX16903 can stay
in dropout by running at 97% duty cycle. It provides an
Maxim Integrated
GND
accurate output voltage within the input range of +6.5V
to +18V. Voltage quality can be monitored by observing
the PGOOD signal. The MAX16903 operates at 2.1MHz
(typ) frequency, which allows for small external components, reduced output ripple, and guarantees no AM
band interference.
7
MAX16903
2.1MHz, High-Voltage, 1A Mini-Buck Converter
The MAX16903 features an ultra-low 25μA (typ) quiescent supply current in standby mode. Standby mode is
entered when load currents are below 5mA and when
SYNC is low. The MAX16903 operates from a +3.5V to
+28V supply voltage and tolerates transients up to
+42V, making it ideal for automotive applications. The
MAX16903 is available in factory-trimmed output voltages from 1.8V to 10.7V in 100mV steps. Please contact factory for availability of voltage options.
Enable (EN)
The MAX16903 is activated by driving EN high. EN is
compatible from a +3.3V logic level to automotive battery levels. EN can be controlled by microcontrollers
and automotive KEY or CAN inhibit signals. The EN
input has no internal pullup/pulldown current to minimize overall quiescent supply current. To realize a programmable undervoltage lockout level, use a resistordivider from SUP to EN to GND.
BIAS/UVLO
The MAX16903 features undervoltage lockout. When the
device is enabled, an internal bias generator turns on.
LX begins switching after VBIAS has exceeded the internal undervoltage lockout level VUVLO = 3V (typ).
Soft-Start
The MAX16903 features an internal soft-start timer. The
output voltage soft-start ramp time is 8ms (typ). If a
short circuit or undervoltage is encountered, after the
soft-start timer has expired, the device is disabled for
30ms (typ) and it reattempts soft-start again. This pattern repeats until the short circuit has been removed.
Oscillator/Synchronization and
Efficiency (SYNC)
The MAX16903 has an on-chip oscillator that provides
a switching frequency of 2.1MHz (typ). Depending on
the condition of SYNC, two operation modes exist. If
SYNC is unconnected or at GND, the device must operate in highly efficient pulse-skipping mode if the load
current is below the SKIP mode current threshold. If
SYNC is at BIAS or has a frequency applied to it, the
device is in forced PWM mode. The MAX16903 offers
the best of both worlds. The device can be switched
during operation between forced PWM mode and SKIP
mode by switching SYNC.
SKIP Mode Operation
SKIP mode is entered when the SYNC pin is connected to
ground or is unconnected and the peak load current is
< 350mA (typ). In this mode, the high-side FET is turned
on until the current in the inductor is ramped up to 350mA
(typ) peak value and the internal feedback voltage is
above the regulation voltage (1.2V typ). At this point, both
8
the high-side and low-side FETs are turned off.
Depending on the choice of the output capacitor and the
load current the high-side FET turns on when OUTS (valley) drops below the 1.2V (typ) feedback voltage.
Achieving High Efficiency at Light Loads
The MAX16903 operates with very low quiescent current
at light loads to enhance efficiency and conserve battery
life. When the MAX16903 enters SKIP mode the output
current is monitored to adjust the quiescent current.
When the output current is < 5mA, the MAX16903 operates in the lowest quiescent current mode also called the
standby mode. In this mode, the majority of the internal
circuitry (excluding that necessary to maintain regulation)
in the MAX16903, including the internal high-voltage
LDO, is turned off to save current. Under no load and
with SKIP mode enabled, the IC draws only 25μA (typ)
current. For load currents > 5mA, the IC enters normal
SKIP mode still maintaining very high efficiency.
Controlled EMI with Forced-Fixed Frequency
In forced PWM mode, the MAX16903 attempts to operate at a constant switching frequency for all load currents. For tightest frequency control, apply the
operating frequency to SYNC. The advantage of this
mode is a constant switching frequency, which
improves EMI performance; the disadvantage is that
considerable current can be thrown away. If the load
current during a switching cycle is less than the current
flowing through the inductor, the excess current is
diverted to GND. With no external load present, the
operating current is in the 10mA range.
Extended Input Voltage Range
In some cases, the MAX16903 is forced to deviate from
its operating frequency independent of the state of SYNC.
For input voltages above 18V, the required duty cycle to
regulate its output may be smaller than the minimum ontime (80ns, typ). In this event, the MAX16903 is forced to
lower its switching frequency by skipping pulses.
If the input voltage is reduced and the MAX16903
approaches dropout the device tries to turn on the highside FET continuously. In order to maintain gate charge
on the high-side FET, the BST capacitor must be periodically recharged. To ensure proper charge on the BST
capacitor when in dropout, the high-side FET is turned
off every 6.5μs and the low-side FET is turned on for
about 150ns. This gives an effective duty cycle of > 97%
and a switching frequency of 150kHz when in dropout.
Spread-Spectrum Option
The MAX16903 has an optional spread-spectrum version.
If this option is selected, then the internal operating frequency varies by +6% relative to the internally generated
Maxim Integrated
MAX16903
2.1MHz, High-Voltage, 1A Mini-Buck Converter
operating frequency of 2.1MHz (typ). Spread spectrum is
offered to improve EMI performance of the MAX16903. By
varying the frequency 6% only in the positive direction,
the MAX16903 still guarantees that the 2.1MHz frequency
does not drop into the AM band limit of 1.8MHz.
Additionally, with the low minimum on-time of 80ns (typ)
no pulse skipping is observed for a 5V output with 18V
input maximum battery voltage in steady state.
The internal spread spectrum does not interfere with
the external clock applied on the SYNC pin. It is active
only when the MAX16903 is running with internally generated switching frequency.
Table 1. Nominal Output Voltage Values
VOUT (V)
LNOM (μH)
1.8 to 3.1
VOUT/0.55
3.2 to 6.5
VOUT/0.96
6.6 to 8.1
VOUT/1.40
8.2 to 10
VOUT/1.75
Table 2. Examples for Standard Output
Voltages
Power-Good (PGOOD)
The MAX16903 features an open-drain power-good
output. PGOOD is an active-high output that pulls low
when the output voltage is below 91% of its nominal
value. PGOOD is high impedance when the output voltage is above 93% of its nominal value. Connect a 20kΩ
(typ) pullup resistor to an external supply or the on-chip
BIAS output.
Overcurrent Protection
The MAX16903 limits the peak output current to 1.5A
(typ). The accuracy of the current limit is ±15%, which
makes selection of external components very easy. To
protect against short-circuit events, the MAX16903 will
shut off when OUTS is below 1.5V (typ) and one overcurrent event is detected. The MAX16903 attempts a
soft-start restart every 30ms and stays off if the short circuit has not been removed. When the current limit is no
longer present, it reaches the output voltage by following the normal soft-start sequence. If the MAX16903 die
reaches the thermal limit of 175°C (typ) during the current-limit event, it immediately shuts off.
Thermal-Overload Protection
The MAX16903 features thermal-overload protection.
The device turns off when the junction temperature
exceeds +175°C (typ). Once the device cools by 15°C
(typ), it turns back on with a soft-start sequence.
Applications Information
Inductor Selection
The nominal inductor value can be calculated using
Table 1 based on the nominal output voltage of the
device. Select the nearest standard inductance value to
the calculated nominal value. The nominal standard
value selected should be within ±25% of LNOM for best
performance.
Maxim Integrated
VOUT (V)
CALCULATED
LNOM (μH)
STANDARD
VALUE (μH)
1.8
3.3
3.3
3.3
3.4
3.3
5.0
5.2
4.7
8.0
5.7
5.6
Input Capacitor
A low-ESR ceramic input capacitor of 1μF or larger is
needed for proper device operation. This value may
need to be larger based on application input-voltage
ripple requirements.
The discontinuous input current of the buck converter
causes large input ripple current. The switching frequency, peak inductor current, and the allowable peak-topeak input-voltage ripple dictate the input capacitance
requirement. Increasing the switching frequency or the
inductor value lowers the peak-to-average current ratio
yielding a lower input capacitance requirement.
The input ripple comprises mainly of ΔVQ (caused by
the capacitor discharge) and ΔVESR (caused by the
ESR of the input capacitor). The total voltage ripple is
the sum of ΔVQ and ΔVESR. Assume the input-voltage
ripple from the ESR and the capacitor discharge is
equal to 50% each. The following equations show the
ESR and capacitor requirement for a target voltage ripple at the input:
ΔVESR
ESR =
ΔIP − P ⎞
⎛
⎜⎝ IOUT +
⎟
2 ⎠
I
× D(1 − D)
CIN = OUT
ΔVQ × fSW
9
MAX16903
2.1MHz, High-Voltage, 1A Mini-Buck Converter
where:
(V − VOUT ) × VOUT
ΔIP − P = IN
VIN × fSW × L
and
V
D = OUT
VIN
where IOUT is the output current, D is the duty cycle,
and f SW is the switching frequency. Use additional
input capacitance at lower input voltages to avoid possible undershoot below the UVLO threshold during transient loading.
Output Capacitor
To maintain acceptable phase margin, a minimum
ceramic output capacitor value of 10μF is needed with
a voltage rating 2 times the VOUT voltage. Additional
output capacitance may be needed based on application-specific output-voltage ripple requirements.
The allowable output-voltage ripple and the maximum
deviation of the output voltage during step load currents determine the output capacitance and its ESR.
The output ripple comprises of ΔVQ (caused by the
capacitor discharge) and ΔVESR (caused by the ESR of
the output capacitor). Use low-ESR ceramic or aluminum electrolytic capacitors at the output. For aluminum electrolytic capacitors, the entire output ripple is
contributed by ΔVESR. Use the ESROUT equation to calculate the ESR requirement and choose the capacitor
accordingly. If using ceramic capacitors, assume the
contribution to the output ripple voltage from the ESR
and the capacitor discharge to be equal. The following
equations show the output capacitance and ESR
requirement for a specified output-voltage ripple.
ESR =
COUT =
ΔVESR
ΔIP − P
ΔIP − P
8 × ΔVQ × fSW
where:
ΔIP − P =
(VIN − VOUT ) × VOUT
VIN × fSW × L
VOUT _ RIPPLE ≅ ΔVESR + ΔVQ
10
ΔIP-P is the peak-to-peak inductor current as calculated
above and fSW is the converter’s switching frequency.
The allowable deviation of the output voltage during
fast transient loads also determines the output capacitance and its ESR. The output capacitor supplies the
step load current until the converter responds with a
greater duty cycle. The response time (t RESPONSE )
depends on the closed-loop bandwidth of the converter. The high switching frequency of the MAX16903
allows for a higher closed-loop bandwidth, thus reducing t RESPONSE and the output capacitance requirement. The resistive drop across the output capacitor’s
ESR and the capacitor discharge causes a voltage
droop during a step load. Use a combination of lowESR tantalum and ceramic capacitors for better transient load and ripple/noise performance. Keep the
maximum output-voltage deviations below the tolerable
limits of the electronics being powered. When using a
ceramic capacitor, assume an 80% and 20% contribution from the output capacitance discharge and the
ESR drop, respectively. Use the following equations to
calculate the required ESR and capacitance value:
ESROUT =
ΔVESR
ISTEP
I
× tRESPONSE
COUT = STEP
ΔVQ
where I STEP is the load step and t RESPONSE is the
response time of the converter. The converter response
time depends on the control-loop bandwidth.
PCB Layout Guidelines
Careful PCB layout is critical to achieve low switching
power losses and clean stable operation. Use a multilayer
board wherever possible for better noise immunity. Refer
to MAX16903 Evaluation Kit for recommended PCB layout. Follow these guidelines for a good PCB layout:
1) The input capacitor (4.7μF, see the applications
schematic in the Typical Operating Circuits) should be
placed right next to the SUP pins (pins 2 and 3 on the
TSSOP-EP package) of the MAX16903. Since the
MAX16903 operates at 2.1MHz switching frequency,
this placement is critical for effective decoupling of
high-frequency noise from the SUP pins.
2) Solder the exposed pad to a large copper plane
area under the device. To effectively use this copper
area as heat exchanger between the PCB and ambient expose the copper area on the top and bottom
side. Add a few small vias or 1 large via on the cop-
Maxim Integrated
MAX16903
2.1MHz, High-Voltage, 1A Mini-Buck Converter
per pad for efficient heat transfer. Connect the
exposed pad to PGND ideally at the return terminal
of the output capacitor.
3) Isolate the power components and high current
paths from sensitive analog circuitry.
4) Keep the high current paths short especially at the
ground terminals. The practice is essential for stable
jitter-free operation.
1MΩ
CHARGE-CURRENTLIMIT RESISTOR
HIGHVOLTAGE
DC
SOURCE
CS
100pF
RD
1.5kΩ
DISCHARGE
RESISTANCE
STORAGE
CAPACITOR
DEVICE
UNDER
TEST
5) Connect the PGND and GND together preferably at
the return terminal of the output capacitor. Do not
connect them anywhere else.
6) Keep the power traces and load connections short.
This practice is essential for high efficiency. Use
thick copper PCB to enhance full load efficiency and
power dissipation capability.
7) Route high-speed switching nodes away from sensitive analog areas. Use internal PCB layers as PGND
to act as EMI shields to keep radiated noise away
from the device and analog bypass capacitor.
ESD Protection
The ESD tolerance for the MAX16903 is rated for Human
Body Model and Machine Model. The Human Body
Model discharge components are CS = 100pF and RD
= 1.5kΩ (Figure 1). The Machine Model discharge components are CS = 200pF and RD = 0Ω (Figure 2).
Maxim Integrated
Figure 1. Human Body ESD Test Circuit
RD
0Ω
CHARGE-CURRENTLIMIT RESISTOR
HIGHVOLTAGE
DC
SOURCE
CS
200pF
DISCHARGE
RESISTANCE
STORAGE
CAPACITOR
DEVICE
UNDER
TEST
Figure 2. Machine Model ESD Test Circuit
11
MAX16903
2.1MHz, High-Voltage, 1A Mini-Buck Converter
Selector Guide
OUTPUT VOLTAGE
(V)
PIN-PACKAGE
SPREAD-SPECTRUM
SWITCHING FREQUENCY
TOP
MARK
MAX16903RATB50+
5
10 TDFN-EP*
(3mm x 3mm x 0.75mm)
AZO
MAX16903RATB50/V+
5
10 TDFN-EP*
(3mm x 3mm x 0.75mm)
AVU
MAX16903RAUE50+
5
16 TSSOP-EP*
(5mm x 4.4mm)
MAX16903RAUE50/V+
5
16 TSSOP-EP*
(5mm x 4.4mm)
MAX16903SATB50+
5
10 TDFN-EP*
(3mm x 3mm x 0.75mm)
Yes
AZQ
MAX16903SATB50/V+
5
10 TDFN-EP*
(3mm x 3mm x 0.75mm)
Yes
AVW
MAX16903SAUE50+
5
16 TSSOP-EP*
(5mm x 4.4mm)
Yes
MAX16903SAUE50/V+
5
16 TSSOP-EP*
(5mm x 4.4mm)
Yes
MAX16903RATB33+
3.3
10 TDFN-EP*
(3mm x 3mm x 0.75mm)
AZN
MAX16903RATB33/V+
3.3
10 TDFN-EP*
(3mm x 3mm x 0.75mm)
AVT
MAX16903RAUE33+
3.3
16 TSSOP-EP*
(5mm x 4.4mm)
MAX16903RAUE33/V+
3.3
16 TSSOP-EP*
(5mm x 4.4mm)
MAX16903SATB33+
3.3
10 TDFN-EP*
(3mm x 3mm x 0.75mm)
Yes
AZP
MAX16903SATB33/V+
3.3
10 TDFN-EP*
(3mm x 3mm x 0.75mm)
Yes
AVV
MAX16903SAUE33+
3.3
16 TSSOP-EP*
(5mm x 4.4mm)
Yes
MAX16903SAUE33/V+
3.3
16 TSSOP-EP*
(5mm x 4.4mm)
Yes
PART
Note: All devices operate over the -40°C to +125°C automotive temperature range.
+Denotes a lead(Pb)-free/RoHS-compliant package.
/V denotes an automotive qualified part.
*EP = Exposed pad.
12
Maxim Integrated
MAX16903
2.1MHz, High-Voltage, 1A Mini-Buck Converter
Package Information
Chip Information
PROCESS: BiCMOS
Maxim Integrated
For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a
“+”, “#”, or “-” in the package code indicates RoHS status only.
Package drawings may show a different suffix character, but the
drawing pertains to the package regardless of RoHS status.
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE
NO.
LAND
PATTERN NO.
10 TDFN-EP
T1033+1
21-0137
90-0003
16 TSSOP-EP
U16E+3
21-0108
90-0120
13
MAX16903
2.1MHz, High-Voltage, 1A Mini-Buck Converter
Revision History
REVISION
NUMBER
REVISION
DATE
0
10/09
1
7/10
Updated the General Description, Typical Operating Circuits, Absolute Maximum Ratings,
Electrical Characteristics table, Typical Operating Characteristics, Pin Description, and
Detailed Description
2
8/10
Corrected a typo in the TSSOP Pin Configuration (pin 2 is SUP, not N.C.)
3
3/11
Updated the Voltage Accuracy and DMOS Peak Current-Limit Threshold parameters in
the Electrical Characteristics, updated the high-side FET in the Skip Mode Operation
section and the output current in the Inductor Selection section
4
6/13
Replaced the Inductor Selection section, and updated the Input Capacitor, Output
Capacitor, and Selector Guide sections
DESCRIPTION
Initial release
PAGES
CHANGED
—
1–10
6
3, 4, 8, 9
9–11
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent
licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and
max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
14 ________________________________Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000
© 2013 Maxim Integrated Products, Inc.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.