MAXIM MAX5387LAUD+

19-5140; Rev 1; 4/10
TION KIT
EVALUA BLE
AVAILA
Dual, 256-Tap, Volatile, Low-Voltage
Linear Taper Digital Potentiometer
Features
The MAX5387 dual, 256-tap, volatile, low-voltage linear taper digital potentiometer offers three end-to-end
resistance values of 10kI, 50kI, and 100kI. Operating
from a single +2.6V to +5.5V power supply, the device
provides a low 35ppm/NC end-to-end temperature coefficient. The device features an I2C interface.
S Dual, 256-Tap Linear Taper Positions
The small package size, low supply operating voltage,
low supply current, and automotive temperature range
of the MAX5387 make the device uniquely suitable for
the portable consumer market, battery backup industrial
applications, and the automotive market.
S Power-On Sets Wiper to Midscale
S Single +2.6V to +5.5V Supply Operation
S Low < 1µA Quiescent Supply Current
S 10kI, 50kI, 100kI End-to-End Resistance Values
S I2C-Compatible Interface
S -40NC to + 125NC Operating Temperature Range
The MAX5387 is specified over the automotive -40NC to
+125NC temperature range and is available in a 14-pin
TSSOP package.
Ordering Information
Applications
Low-Voltage Battery Applications
PART
Portable Electronics
PIN-PACKAGE
END-TO-END
RESISTANCE (kI)
Mechanical Potentiometer Replacement
MAX5387LAUD+
14 TSSOP
Offset and Gain Control
MAX5387MAUD+
14 TSSOP
50
MAX5387NAUD+
14 TSSOP
100
Adjustable Voltage References/Linear Regulators
10
Note: All devices are specified over the -40NC to +125NC operating temperature range.
+Denotes a lead(Pb)-free/RoHS-compliant package.
Automotive Electronics
Functional Diagram
VDD
SCL
HA
LATCH
WA
256 DECODER
SDA
A0
HB
I2C
POR
MAX5387
A1
A2
LA
LATCH
256 DECODER
WB
LB
GND
________________________________________________________________ Maxim Integrated Products 1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
MAX5387
General Description
MAX5387
Dual, 256-Tap, Volatile, Low-Voltage
Linear Taper Digital Potentiometer
ABSOLUTE MAXIMUM RATINGS
Continuous Power Dissipation (TA = +70NC)
14-Pin TSSOP (derate 10mW/NC above +70NC).......796.8mW
Operating Temperature Range . ...................... -40NC to +125NC
Junction Temperature .....................................................+150NC
Storage Temperature Range............................. -65NC to +150NC
Lead Temperature (soldering, 10s).................................+300NC
Soldering Temperature (reflow).......................................+260NC
VDD to GND ............................................................-0.3V to +6V
H_, W_, L_ to GND.......................................-0.3V to the lower of
(VDD + 0.3V) and +6V
All Other Pins to GND..............................................-0.3V to +6V
Continuous Current into H_, W_, and L_
MAX5387L...................................................................... Q5mA
MAX5387M..................................................................... Q2mA
MAX5387N...................................................................... Q1mA
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VDD = +2.6V to +5.5V, VH__ = VDD, VL__= GND, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD = +5V,
TA = +25NC.) (Note 1)
PARAMETER
Resolution
SYMBOL
CONDITIONS
N
MIN
TYP
MAX
256
UNITS
Tap
DC PERFORMANCE (Voltage-Divider Mode)
Integral Nonlinearity
INL
(Note 2)
-0.5
+0.5
LSB
Differential Nonlinearity
DNL
(Note 2)
-0.5
+0.5
LSB
Dual Code Matching
Register A = register B
-0.5
+0.5
LSB
Ratiometric Resistor Tempco
(DVW/VW)/DT; no load
Full-Scale Error
Code = FFH
Zero-Scale Error
Code = 00H
+5
MAX5387L
-3
-2.5
MAX5387M
-1
-0.5
MAX5387N
-0.5
-0.25
LSB
LSB
MAX5387L
+2.5
+3
MAX5387M
+0.5
+1.0
MAX5387N
+0.25
+0.5
LSB
DC PERFORMANCE (Variable-Resistor Mode)
VDD > +2.6V
Integral Nonlinearity
R-INL
VDD > +4.75V
MAX5387L
±1.0
±2.5
MAX5387M
±0.5
±1.0
MAX5387N
±0.25
±0.8
MAX5387L
±0.4
±1.5
MAX5387M
±0.3
±0.75
±0.25
±0.5
MAX5387N
Differential Nonlinearity
R-DNL
VDD > 2.6V (Note 3)
-0.5
+0.5
LSB
LSB
DC PERFORMANCE (Resistor Characteristics)
Wiper Resistance (Note 4)
RWL
VDD > 2.6V
250
600
VDD > 4.75V
150
200
I
CH_, CL_
Measured to GND
10
pF
CW_
Measured to GND
50
pF
End-to-End Resistor Tempco
TCR
No load
End-to-End Resistor Tolerance
DRHL
Wiper not connected
Terminal Capacitance
Wiper Capacitance
35
-25
2 _______________________________________________________________________________________
ppm/NC
+25
%
Dual, 256-Tap, Volatile, Low-Voltage
Linear Taper Digital Potentiometer
(VDD = +2.6V to +5.5V, VH__ = VDD, VL__= GND, TA = -40NC to +125NC, unless otherwise noted. Typical values are at VDD = +5V,
TA = +25NC.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
AC PERFORMANCE
Crosstalk
(Note 5)
-3dB Bandwidth
BW
Total Harmonic Distortion Plus
Noise
Wiper Settling Time (Note 6)
THD+N
tS
Code = 80H,
10pF load,
VDD = +2.6V
-90
MAX5387L
600
MAX5387M
150
MAX5387N
75
dB
kHz
Measured at W; VH_ = 1VRMS at 1kHz
0.015
%
MAX5387L
MAX5387M
MAX5387N
300
1000
2000
ns
POWER SUPPLIES
Supply-Voltage Range
2.6
VDD
Digital inputs = VDD or GND
Standby Current
5.5
1
V
FA
DIGITAL INPUTS
Minimum Input High Voltage
VIH
Maximum Input Low Voltage
VIL
70
Input Leakage Current
% x VDD
-1
Input Capacitance
30
% x VDD
+1
FA
5
pF
TIMING CHARACTERISTICS (Notes 7, 8)
Maximum SCL Frequency
400
fSCL
kHz
Setup Time for START Condition
tSU:STA
0.6
Fs
Hold Time for START Condition
tHD:STA
0.6
Fs
SCL High Time
tHIGH
0.6
Fs
SCL Low Time
tLOW
1.3
Fs
Data Setup Time
tSU:DAT
100
ns
Data Hold Time
tHD:DAT
0
Fs
SDA, SCL Rise Time
tR
0.3
Fs
SDA, SCL Fall
tF
0.3
Fs
Setup Time for STOP Condition
Bus Free Time Between STOP and
START Conditions
tSU:STO
tBUF
Minimum power-up rate = 0.2V/Fs
0.6
Fs
1.3
Fs
Pulse-Suppressed Spike Width
tSP
50
ns
Capacitive Load for Each Bus
CB
400
pF
Note 1: All devices are 100% production tested at TA = +25NC. Specifications overtemperature limits are guaranteed by design
and characterization.
Note 2: DNL and INL are measured with the potentiometer configured as a voltage-divider (Figure 1) with H_ = VDD and L_ = 0V.
The wiper terminal is unloaded and measured with an ideal voltmeter.
Note 3: R-DNL and R-INL are measured with the potentiometer configured as a variable resistor (Figure 1). DNL and INL are
measured with the potentiometer configured as a variable resistor. H_ is unconnected and L_ = GND. For VDD = +5V, the
wiper terminal is driven with a source current of 400FA for the 10kI configuration, 80FA for the 50kI configuration, and
40FA for the 100kI configuration. For VDD = +2.6V, the wiper terminal is driven with a source current of 200FA for the
10kI configuration, 40FA for the 50kI configuration, and 20FA for the 100kI configuration.
Note 4: The wiper resistance is the worst value measured by injecting the currents given in Note 3 into W_ with L_ = GND. RW =
(VW - VH)/IW.
_______________________________________________________________________________________ 3
MAX5387
ELECTRICAL CHARACTERISTICS (continued)
Note 5: Drive HA with a 1kHz GND to VDD amplitude tone. LA = LB = GND. No load. WB is at midscale with a 10pF load.
Measure WB.
Note 6: The wiper settling time is the worst-case 0 to 50% rise time, measured between tap 0 and tap 127. H_ = VDD, L_ = GND,
and the wiper terminal is loaded with 10pF capacitance to ground.
Note 7: Digital timing is guaranteed by design and characterization, not production tested.
Note 8: The SCL clock period includes rise and fall times (tR = tF). All digital input signals are specified with tR = tF = 2ns and
timed from a voltage level of (VIL + VIH)/2.
H
N.C.
W
W
L
L
Figure 1. Voltage-Divider and Variable Resistor Configurations
Typical Operating Characteristics
(VDD = 5V, TA = +25°C, unless otherwise noted.)
SUPPLY CURRENT
vs. DIGITAL INPUT VOLTAGE
VDD = 5V
0.7
0.6
0.5
0.4
VDD = 2.6V
0.3
1000
SUPPLY CURRENT (µA)
0.2
VDD = 5V
1.0
0.9
0.8
0.7
100
VDD = 2.6V
10
0.6
0.5
0.4
0.3
0.2
1
0.1
0.1
0
0
0.1
-40 -25 -10 5 20 35 50 65 80 95 110 125
0
2.6
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
3.6
4.1
4.6
5.1
DIGITAL INPUT VOLTAGE (V)
VDD (V)
RESISTANCE (W-TO-L)
vs. TAP POSITION (10kI)
RESISTANCE (W-TO-L)
vs. TAP POSITION (50kI)
RESISTANCE (W-TO-L)
vs. TAP POSITION (100kI)
W-TO-L RESISTANCE (kΩ)
9
50
8
7
6
5
4
3
110
45
100
RESISTANCE (W-TO-L) (kI)
10
MAX5387 toc05
55
MAX5387 toc04
11
40
35
30
25
20
15
90
80
70
60
50
40
30
2
10
20
1
5
10
0
0
0
3.1
TEMPERATURE (°C)
51
102
153
TAP POSITION
204
255
0
51
102
153
TAP POSITION
204
255
MAX5387 toc06
SUPPLY CURRENT (µA)
0.8
10,000
MAX5387 toc03
0.9
IDD (µA)
MAX5387 toc01
1.0
SUPPLY CURRENT
vs. SUPPLY VOLTAGE
MAX5387 toc02
SUPPLY CURRENT vs. TEMPERATURE
W-TO-L RESISTANCE (kΩ)
MAX5387
Dual, 256-Tap, Volatile, Low-Voltage
Linear Taper Digital Potentiometer
0
0
51
102
153
TAP POSITION
4 _______________________________________________________________________________________
204
255
Dual, 256-Tap, Volatile, Low-Voltage
Linear Taper Digital Potentiometer
END-TO-END RESISTANCE % CHANGE
vs. TEMPERATURE
110
90
50kI
-0.2
100kI
-0.3
-0.06
-0.4
-0.08
-0.10
0
1.0
0.06
0.6
0.2
INL (LSB)
0.4
0
-0.02
0
-0.04
-0.4
-0.06
-0.06
-0.6
-0.08
-0.08
-0.8
-0.10
204
-1.0
0
51
102
153
204
255
0
102
153
204
TAP POSITION
TAP POSITION
VARIABLE-RESISTOR INL
vs. TAP POSITION (50kI)
VARIABLE-RESISTOR INL
vs. TAP POSITION (100kI)
VOLTAGE-DIVIDER DNL
vs. TAP POSITION (10kI)
0.5
IWIPER = 400µA
0.4
0.10
MAX5387 toc14
0.3
0.3
0.08
0.06
0.04
0.1
0.1
0.02
0
-0.1
DNL (LSB)
0.2
INL (LSB)
0.2
0
-0.1
0
-0.2
-0.04
-0.3
-0.3
-0.06
-0.4
-0.4
-0.08
-0.5
-0.5
51
102
153
TAP POSITION
204
255
255
-0.02
-0.2
0
51
TAP POSITION
IWIPER = 80µA
0.4
255
MAX5387 toc13
0.5
153
255
-0.2
-0.04
102
IWIPER = 400µA
0.8
0.02
51
204
VARIABLE-RESISTOR INL
vs. TAP POSITION (10kI)
0.02
0
153
VARIABLE-RESISTOR DNL
vs. TAP POSITION (100kI)
0.04
-0.02
102
TAP POSITION
0.04
0
51
TEMPERATURE (NC)
IWIPER = 400µA
0.08
-0.10
INL (LSB)
0
-0.02
-0.04
0.10
DNL (LSB)
DNL (LSB)
0.06
0.02
-40 -25 -10 5 20 35 50 65 80 95 110 125
MAX5387 toc10
IWIPER = 80µA
0.08
MAX5387 toc09
0.04
-0.1
VARIABLE-RESISTOR DNL
vs. TAP POSITION (50kI)
0.10
0.06
-0.5
0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
WIPER VOLTAGE (V)
IWIPER = 400µA
0.08
MAX5386 toc15
70
0
MAX5387 toc12
VDD = 5V
130
0.10
DNL (LSB)
150
10kI
MAX5387 toc11
170
0.1
END-TO-END RESISTANCE % CHANGE
VDD = 2.6V
190
WIPER RESISTANCE (Ω)
MAX5387 toc07
210
VARIABLE-RESISTOR DNL
vs. TAP POSITION (10kI)
MAX5387 toc08
WIPER RESISTANCE
vs. WIPER VOLTAGE (10kI)
-0.10
0
51
102
153
TAP POSITION
204
255
0
51
102
153
204
255
TAP POSITION
_______________________________________________________________________________________ 5
MAX5387
Typical Operating Characteristics (continued)
(VDD = 5V, TA = +25°C, unless otherwise noted.)
Typical Operating Characteristics (continued)
(VDD = 5V, TA = +25°C, unless otherwise noted.)
0.06
VOLTAGE-DIVIDER INL
vs. TAP POSITION (10kI)
0.5
MAX5387 toc17
0.08
0.08
0.06
0.4
0.3
0.04
0.2
0.02
0.02
0.1
0
-0.02
INL (LSB)
0.04
DNL (LSB)
0
-0.02
0
-0.1
-0.04
-0.04
-0.2
-0.06
-0.06
-0.3
-0.08
-0.08
-0.4
-0.10
-0.10
0
51
102
153
204
255
-0.5
0
51
102
153
204
255
0
51
102
153
255
TAP POSITION
TAP POSITION
VOLTAGE-DIVIDER INL
vs. TAP POSITION (50kI)
VOLTAGE-DIVIDER INL
vs. TAP POSITION (100kI)
TAP-TO-TAP SWITCHING TRANSIENT
(CODE 127 TO 128) (10kI)
0.4
0.3
0.4
0.3
0.2
0.1
0.1
INL (LSB)
0.2
0
-0.1
VW-L
20mV/div
0
-0.1
-0.2
-0.2
-0.3
-0.3
-0.4
-0.4
-0.5
MAX5387 toc21
0.5
MAX5386 toc19
0.5
SCL
5V/div
-0.5
0
204
TAP POSITION
MAX5387 toc20
DNL (LSB)
0.10
MAX5387 toc16
0.10
VOLTAGE-DIVIDER DNL
vs. TAP POSITION (100kI)
MAX5387 toc18
VOLTAGE-DIVIDER DNL
vs. TAP POSITION (50kI)
INL (LSB)
MAX5387
Dual, 256-Tap, Volatile, Low-Voltage
Linear Taper Digital Potentiometer
51
102
153
204
255
0
51
TAP POSITION
102
153
204
255
400ns/div
TAP POSITION
TAP-TO-TAP SWITCHING TRANSIENT
(CODE 127 TO 128) (50kI)
TAP-TO-TAP SWITCHING TRANSIENT
(CODE 127 TO 128) (100kI)
MAX5387 toc22
1µs/div
MAX5387 toc23
VW-L
20mV/div
VW-L
20mV/div
SCL
5V/div
SCL
5V/div
1µs/div
6 _______________________________________________________________________________________
Dual, 256-Tap, Volatile, Low-Voltage
Linear Taper Digital Potentiometer
MAX5387 POWER-ON WIPER TRANSIENT
(CODE 0 TO 128)
10
MAX5387 toc25
MIDSCALE FREQUENCY RESPONSE
MAX5387 toc24
VIN = 1VP-P
CW = 10pF
GAIN (dB)
0
OUTPUT W
2V/div
MAX5387L
-10
MAX5387M
-20
VDD
2V/div
MAX5387N
-30
2µs/div
0.01
0.1
1
10
100
1,000 10,000
FREQUENCY (kHz)
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. FREQUENCY
CROSSTALK vs. FREQUENCY
0.12
MAX5387L
-60
-80
-100
MAX5387N
MAX5387M
-120
MAX5387M
0.10
THD+N (%)
-40
MAX5387 toc27
-20
CROSSTALK (dB)
0.14
MAX5387 toc26
0
-140
0.08
MAX5387N
0.06
0.04
MAX5387L
0.02
0
0.01
0.1
1
10
FREQUENCY (kHz)
100
1000
0.01
0.10
1
10
100
FREQUENCY (kHz)
_______________________________________________________________________________________ 7
MAX5387
Typical Operating Characteristics (continued)
(VDD = 5V, TA = +25°C, unless otherwise noted.)
Dual, 256-Tap, Volatile, Low-Voltage
Linear Taper Digital Potentiometer
MAX5387
Pin Configuration
TOP VIEW
HA 1
+
14 VDD
13 SCL
WA 2
LA 3
MAX5387
12 SDA
HB 4
11 A0
WB 5
10 A1
LB 6
9 A2
I.C. 7
8 GND
TSSOP
Pin Description
PIN
NAME
FUNCTION
1
HA
Resistor A High Terminal. The voltage at HA can be higher or lower than the voltage at LA. Current
can flow into or out of HA.
2
WA
Resistor A Wiper Terminal
3
LA
Resistor A Low Terminal. The voltage at LA can be higher or lower than the voltage at HA. Current
can flow into or out of LA.
4
HB
Resistor B High Terminal. The voltage at HB can be higher or lower than the voltage at LB. Current
can flow into or out of HB.
5
WB
Resistor B Wiper Terminal
6
LB
Resistor B Low Terminal. The voltage at LB can be higher or lower than the voltage at HB. Current
can flow into or out of LB.
7
I.C.
Internally Connected. Connect to GND.
8
GND
9
A2
Address Input 2. Connect to VDD or GND.
10
A1
Address Input 1. Connect to VDD or GND.
11
A0
12
SDA
Address Input 0. Connect to VDD or GND.
I2C-Compatible Serial-Data Input/Output. A pullup resistor is required.
13
SCL
I2C-Compatible Serial-Clock Input. A pullup resistor is required.
14
VDD
Power-Supply Input. Bypass VDD to GND with a 0.1FF capacitor close to the device.
Ground
8 _______________________________________________________________________________________
Dual, 256-Tap, Volatile, Low-Voltage
Linear Taper Digital Potentiometer
The MAX5387 dual, 256-tap, volatile, low-voltage linear
taper digital potentiometer offers three end-to-end resistance values of 10kI, 50kI, and 100kI. The potentiometer consists of 255 fixed resistors in series between
terminals H_ and L_. The potentiometer wiper, W_, is
programmable to access any one of the 256 tap points
on the resistor string.
The potentiometers are programmable independently of
each other. The MAX5387 features an I2C interface.
I2C Digital Interface
The I2C interface contains a shift register that decodes
the command and address bytes, routing the data to the
appropriate control registers. Data written to a control
register immediately updates the wiper position. Wipers
A and B power up in midposition, D[7:0] = 80H.
Serial Addressing
The MAX5387 operates as a slave device that receives
data through an I2C-/SMBusK-compatible 2-wire serial
interface. The interface uses a serial-data access (SDA)
line and a serial-clock line (SCL) to achieve bidirectional communication between master(s) and slave(s). A
master, typically a microcontroller, initiates all data transfers to the MAX5387, and generates the SCL clock that
synchronizes the data transfer (Figure 2).
The MAX5387 SDA line operates as both an input and
an open-drain output. The SDA line requires a pullup
resistor, typically 4.7kI. The MAX5387 SCL line operates only as an input. The SCL line requires a pullup
resistor (typically 4.7kI) if there are multiple masters on
the 2-wire interface, or if the master in a single-master
system provides an open-drain SCL output.
Each transmission consists of a START (S) condition
(Figure 3) sent by a master, followed by the MAX5387
7-bit slave address plus the NOP/W bit (Figure 6), 1
command byte and 1 data byte, and finally a STOP (P)
condition (Figure 3).
START and STOP Conditions
SCL and SDA remain high when the interface is inactive.
A master controller signals the beginning of a transmission with a START condition by transitioning SDA from
high to low while SCL is high. The master controller issues
a STOP condition by transitioning the SDA from low to
high while SCL is high, after finishing communicating with
the slave. The bus is then free for another transmission.
tHD:STA
SDA
tSU:STD
tSU:DTA
tSU:DAT
tBUF
tHD-DAT
tLOW
SCL
tHIGH
tHD:STA
tR
tF
REPEATED
START CONDITION
(Sr)
START
CONDITION
(S)
ACKNOWLEDGE (A)
STOP CONDITION START CONDITION
(P)
(S)
Figure 2. I2C Serial Interface Timing Diagram
SMBus is a trademark of Intel Corp.
_______________________________________________________________________________________ 9
MAX5387
Detailed Description
MAX5387
Dual, 256-Tap, Volatile, Low-Voltage
Linear Taper Digital Potentiometer
Bit Transfer
One data bit is transferred during each clock pulse. The
data on the SDA line must remain stable while SCL is
high. See Figure 4.
Acknowledge
The acknowledge bit is a clocked 9th bit that the recipient uses to handshake receipt of each byte of data. See
Figure 5. Each byte transferred requires a total of nine
bits. The master controller generates the 9th clock pulse,
and the recipient pulls down SDA during the acknowledge clock pulse, so the SDA line remains stable low
during the high period of the clock pulse.
Slave Address
The MAX5387 includes a 7-bit slave address (Figure 6).
The 8th bit following the 7th bit of the slave address is the
NOP/W bit. Set the NOP/W bit low for a write command
and high for a no-operation command. The device does
not support readback.
The device provides three address inputs (A0, A1, and
A2), allowing up to eight devices to share a common
bus (Table 1). The first 4 bits (MSBs) of the factory-set
slave addresses are always 0101. A2, A1, and A0 set the
next 3 bits of the slave address. Connect each address
input to VDD or GND. Each device must have a unique
address to share a common bus.
SDA
SCL
P
S
START CONDITION
STOP
CONDITION
Figure 3. START and STOP Conditions
SDA
CHANGE OF
DATA ALLOWED
DATA STABLE,
DATA VALID
SCL
Figure 4. Bit Transfer
CLOCK PULSE FOR
ACKNOWLEDGMENT
START
CONDITION
SCL
1
2
8
9
NOT ACKNOWLEDGE
SDA
ACKNOWLEDGE
Figure 5. Acknowledge
10 �������������������������������������������������������������������������������������
Dual, 256-Tap, Volatile, Low-Voltage
Linear Taper Digital Potentiometer
START
0
1
0
1
A2
A1
A0
MSB
NOP/W
MAX5387
SDA
ACK
LSB
SCL
Figure 6. Slave Address
ACKNOWLEDGE
HOW CONTROL BYTE AND DATA
BYTE MAP INTO DEVICE REGISTERS
R7
R6
R5
R4
R3
R2
R1
R0
D7
D6
D5
D4
D3
D2
D1
D0
ACKNOWLEDGE
S
0
A
SLAVE ADDRESS
A
A
COMMAND BYTE
P
1 DATA BYTE
NOP/W
Figure 7. Command and Single Data Byte Received
Message Format for Writing
Write to the devices by transmitting the device’s slave
address with NOP/W (eighth bit) set to zero, followed by
at least 2 bytes of information. The first byte of information is the command byte. The second byte is the data
byte. The data byte goes into the internal register of the
device as selected by the command byte (Figure 7 and
Table 2).
Command Byte
Use the command byte to select the destination of the
wiper data. See Table 2.
Command Descriptions
REG A: The data byte writes to register A and the wiper
of potentiometer A moves to the appropriate position.
D[7:0] indicates the position of the wiper. D[7:0] = 00h
moves the wiper to the position closest to LA. D[7:0] =
FFh moves the wiper to the position closest to HA. D[7:0]
is 80h following power-on.
Table 1. Slave Addresses
ADDRESS INPUTS
SLAVE ADDRESS
A2
A1
A0
GND
GND
GND
0101000
GND
GND
VDD
0101001
GND
VDD
GND
0101010
GND
VDD
VDD
0101011
VDD
GND
GND
0101100
VDD
GND
VDD
0101101
VDD
VDD
GND
0101110
VDD
VDD
VDD
0101111
______________________________________________________________________________________ 11
Table 2. I2C Command Byte Summary
SCL
CYCLE NO.
COMMAND BYTE
1
2
3
4
5
6
7
8
A6
A5
A4
A3
A2
A1
A0
W
9
ACK
(A)
DATA BYTE
10
11
12
13
14
15
16
17
R7
R6
R5
R4
R3
R2
R1
R0
18
ACK
(A)
19
20
21
22
23
24
25
26
D7
D6
D5
D4
D3
D2
D1
D0
REG A
0
1
0
1
A2
A1
A0
0
0
0
0
1
0
0
0
1
D7
D6
D5
D4
D3
D2
D1
D0
REG B
0
1
0
1
A2
A1
A0
0
0
0
0
1
0
0
1
0
D7
D6
D5
D4
D3
D2
D1
D0
0
1
0
1
A2
A1
A0
0
0
0
0
1
0
0
1
1
D7
D6
D5
D4
D3
D2
D1
D0
REGS
A AND B
REG B: The data byte writes to register B and the wiper
of potentiometer B moves to the appropriate position.
D[7:0] indicates the position of the wiper. D[7:0] = 00h
moves the wiper to the position closest to LB. D[7:0] =
FFh moves the wiper to the position closest to HB. D[7:0]
is 80h following power-on.
REGS A and B: The data byte writes to registers A and
B and the wipers of potentiometers A and B move to
the appropriate position. D[7:0] indicates the position
of the wiper. D[7:0] = 00h moves the wipers to the position closest to L_. D[7:0] = FFh moves the wipers to the
position closest to H_. D[7:0] is 80h following power-on.
27
ACK
(A)
Adjustable Dual Regulator
Figure 10 shows an adjustable dual linear regulator
using a dual potentiometer as two variable resistors.
Adjustable Voltage Reference
Figure 11 shows an adjustable voltage reference circuit
using a potentiometer as a voltage-divider.
H
L
W
VIN
VOUT
Applications Information
Variable Gain Amplifier
Figure 8 shows a potentiometer adjusting the gain of a
noninverting amplifier. Figure 9 shows a potentiometer
adjusting the gain of an inverting amplifier.
Figure 9. Variable Gain Inverting Amplifier
VOUT1
OUT1
VIN
VOUT2
OUT2
VOUT
H
MAX8866
V+
W
L
STOP (P)
ADDRESS BYTE
START (S)
MAX5387
Dual, 256-Tap, Volatile, Low-Voltage
Linear Taper Digital Potentiometer
IN
H
W
H
SET1
W
L
L
SET2
Figure 8. Variable Gain Noninverting Amplifier
Figure 10. Adjustable Dual Linear Regulator
12 �������������������������������������������������������������������������������������
Dual, 256-Tap, Volatile, Low-Voltage
Linear Taper Digital Potentiometer
LCD Bias Control
Figure 13 shows a positive LCD bias control circuit using
a potentiometer as a voltage-divider.
Programmable Filter
Figure 15 shows a programmable filter using a dual
potentiometer.
Offset-Voltage Adjustment Circuit
Figure 16 shows an offset-voltage adjustment circuit
using a dual potentiometer.
Figure 14 shows a positive LCD bias control circuit using
a potentiometer as a variable resistor.
3.0V
+5V
IN
VREF
OUT
MAX6037
H
H
W
W
VOUT
L
L
GND
Figure 11. Adjustable Voltage Reference
Figure 13. Positive LCD Bias Control Using a Voltage-Divider
+5V
R3
H
W
R1
R2
H
W
IS
L
VOUT
VOUT
L
VOUT = IS x ((R3 x (1 + R2/R1)) + R2)
Figure 12. Variable Gain I-to-V Converter
Figure 14. Positive LCD Bias Control Using a Variable Resistor
______________________________________________________________________________________ 13
MAX5387
Variable Gain Current to Voltage Converter
Figure 12 shows a variable gain current to voltage converter using a potentiometer as a variable resistor.
MAX5387
Dual, 256-Tap, Volatile, Low-Voltage
Linear Taper Digital Potentiometer
+5V
WA
WB
VIN
LA
HA
LB
HB
VOUT
R3
VOUT
R1
HA
HB
R2
WA
LA
WB
LB
Figure 15. Programmable Filter
Figure 16. Offset-Voltage Adjustment Circuit
Process Information
PROCESS: BiCMOS
Package Information
For the latest package outline information and land patterns,
go to www.maxim-ic.com/packages. Note that a “+”, “#”, or
“-” in the package code indicates RoHS status only. Package
drawings may show a different suffix character, but the drawing
pertains to the package regardless of RoHS status.
PACKAGE TYPE
PACKAGE CODE
Document No.
14 TSSOP
U14+1
21-0066
14 �������������������������������������������������������������������������������������
Dual, 256-Tap, Volatile, Low-Voltage
Linear Taper Digital Potentiometer
REVISION
NUMBER
REVISION
DATE
0
1/10
Initial release
—
1
4/10
Added Soldering Temperature in Absolute Maximum Ratings; corrected
code in Conditions of -3dB Bandwidth specification in Electrical
Characteristics
2
DESCRIPTION
PAGES
CHANGED
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied.
Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2010
Maxim Integrated Products 15
Maxim is a registered trademark of Maxim Integrated Products, Inc.
MAX5387
Revision History