Maxim MAX544AESA 5v, serial-input, voltage-output, 14-bit dac Datasheet

19-1088; Rev 3; 12/99
+5V, Serial-Input, Voltage-Output, 14-Bit DACs
Features
♦ Full 14-Bit Performance Without Adjustments
♦ +5V Single-Supply Operation
♦ Low Power: 1.5mW
♦ 1µs Settling Time
♦ Unbuffered Voltage Output Directly Drives 60kΩ
Loads
♦ SPI/QSPI/MICROWIRE-Compatible Serial Interface
♦ Power-On Reset Circuit Clears DAC Output to 0V
(unipolar mode)
♦ Schmitt-Trigger Inputs for Direct Optocoupler
Interface
♦ Pin-Compatible 16-Bit Upgrades
(MAX541/MAX542)
Ordering Information
PART
TEMP. RANGE
MAX544ACPA
0°C to +70°C
8 Plastic DIP
MAX544BCPA
0°C to +70°C
8 Plastic DIP
Applications
MAX544ACSA
0°C to +70°C
8 SO
±1/2
MAX544BCSA
0°C to +70°C
8 SO
±1
Digital Offset and Gain Adjustment
Instrumentation
PIN-PACKAGE
INL
(LSB)
The MAX544 is available in 8-pin plastic DIP and SO
packages. The MAX545 is available in 14-pin plastic
DIP and SO packages.
±1/2
±1
Ordering Information continued at end of data sheet.
Industrial Process Control
Automated Test Equipment
Functional Diagrams
Data-Acquisition Systems
VDD
Pin Configurations
TOP VIEW
MAX545
RFB
RFB
INV
OUT 1
AGND 2
8 VDD
MAX544
7 DGND
CS 4
14 VDD
OUT 2
13 INV
AGNDF 3
MAX545
AGNDS 4
5 SCLK
10 DIN
REFF 6
9 N.C.
8
CS 7
RINV
14-BIT DAC
OUT
REFS
AGNDF
12 DGND
11 LDAC
REFS 5
6 DIN
REF 3
RFB 1
REFF
CS
LDAC
SCLK
DIN
DATA LATCH
AGNDS
CONTROL
LOGIC
SERIAL INPUT REGISTER
SCLK
DGND
DIP/SO
DIP/SO
Functional Diagrams continued at end of data sheet.
SPI and QSPI are trademarks of Motorola, Inc.
MICROWIRE is a trademark of National Semiconductor Corp.
________________________________________________________________ Maxim Integrated Products
1
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800.
For small orders, phone 1-800-835-8769.
MAX544/MAX545
General Description
The MAX544/MAX545 are serial-input, voltage-output,
14-bit digital-to-analog converters (DACs) that operate
from a single +5V supply. They provide 14-bit performance (±0.5LSB INL and ±0.9LSB DNL) over temperature without any adjustments. The DAC output is
unbuffered, resulting in a low supply current of 0.3mA
and a low offset error of 0.6mV.
The DAC output range is 0V to VREF. For bipolar operation, matched scaling resistors are provided in the
MAX545 for use with an external precision op amp
(such as the MAX400), generating a ±V REF output
swing. The MAX545 also includes Kelvin-sense connections for the reference and analog ground pins to
reduce layout sensitivity.
A 16-bit serial word is used to load data into the DAC
latch. The 10MHz, 3-wire serial interface is compatible
with SPI™/QSPI™/MICROWIRE™, and it also interfaces
directly with optocouplers for applications requiring isolation. A power-on reset circuit clears the DAC output to 0V
(unipolar mode) when power is initially applied.
MAX544/MAX545
+5V, Serial-Input, Voltage-Output, 14-Bit DACs
ABSOLUTE MAXIMUM RATINGS
VDD to DGND ...........................................................-0.3V to +6V
CS, SCLK, DIN, LDAC to DGND ..............................-0.3V to +6V
REF, REFF, REFS to AGND ........................-0.3V to (VDD + 0.3V)
AGND, AGNDF, AGNDS to DGND .......................-0.3V to +0.3V
OUT, INV to AGND DGND .......................................-0.3V to VDD
RFB to AGND DGND...................................................-6V to +6V
Maximum Current into Any Pin............................................50mA
Continuous Power Dissipation (TA = +70°C)
8-Pin Plastic DIP (derate 9.09mW/°C above +70°C) .....727mW
8-Pin SO (derate 5.88mW/°C above +70°C) .................471mW
14-Pin Plastic DIP (derate 10.00mW/°C above +70°C) ...800mW
14-Pin SO (derate 8.33mW/°C above +70°C) ...............667mW
14-Pin Ceramic SB (derate 10.00mW/°C above +70°C...800mW
Operating Temperature Ranges
MAX544 _C_ A/MAX545_C_D ..............................0°C to +70°C
MAX544 _E_ A/MAX545_E_D............................-40°C to +85°C
MAX545BMJD .................................................-55°C to +125°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VDD = +5V ± 5%, VREF = +2.5V, AGND = DGND = 0, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
STATIC PERFORMANCE—ANALOG SECTION (RL = ∞)
Resolution
N
Integral Nonlinearity
INL
VDD = 5V
Differential Nonlinearity
DNL
Guaranteed monotonic
Zero-Code Offset Error
ZSE
Zero-Code Tempco
ZSTC
MIN
TYP
14
MAX54_A
±0.15
±0.5
MAX54_B
±0.15
±1
±0.15
±0.9
±0.6
±0.05
ROUT
(Note 2)
Bipolar Resistor Matching
MAX545
Bipolar Zero Offset Error
MAX545
Bipolar Zero Tempco
BZSTC
RFB/RINV
mV
LSB
ppm/°C
6.25
kΩ
1.0
MAX545
±0.03
%
±10
LSB
±0.5
Power-Supply Rejection
PSR
4.75V ≤ VDD ≤ 5.25V
REFERENCE INPUT
Reference Input Range
VREF
(Note 3)
2.0
Reference Input Resistance
(Note 4)
RREF
Unipolar mode
11.5
MAX545, bipolar mode
9.0
1
LSB
±0.1
Ratio error
DYNAMIC PERFORMANCE—ANALOG SECTION (RL = ∞, unipolar mode)
Voltage-Output Slew Rate
SR
CL = 10pF (Note 5)
LSB
ppm/°C
±5
Gain-Error Tempco
UNITS
Bits
Gain Error (Note 1)
DAC Output Resistance
MAX
ppm/°C
±1.0
LSB
3.0
V
kΩ
25
V/µs
Output Settling Time
To ± /2LSB of FS, CL = 10pF
1
µs
DAC Glitch Impulse
Major-carry transition
10
nVs
Digital Feedthrough
Code = 0000 hex; CS = VDD; LDAC = 0V;
SCLK, DIN = 0V to VDD levels
10
nVs
2
_______________________________________________________________________________________
+5V, Serial-Input, Voltage-Output, 14-Bit DACs
MAX544/MAX545
ELECTRICAL CHARACTERISTICS (continued)
(VDD = +5V ± 5%, VREF = +2.5V, AGND = DGND = 0, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
DYNAMIC PERFORMANCE—REFERENCE SECTION
Reference -3dB Bandwidth
BW
Reference Feedthrough
Signal-to-Noise Ratio
SNR
Reference Input Capacitance
CIN
Code = FFFC hex
1
MHz
Code = 0000 hex, VREF = 1Vp-p at 100kHz
1
mVp-p
83
dB
Code = 0000 hex
75
Code = FFFC hex
120
pF
STATIC PERFORMANCE—DIGITAL INPUTS
Input High Voltage
VIH
Input Low Voltage
VIL
2.4
Input Current
IIN
VIN = 0
Input Capacitance
CIN
(Note 6)
Hysteresis Voltage
VH
V
0.8
V
±1
µA
10
pF
0.40
V
POWER SUPPLY
Positive Supply Range
VDD
Positive Supply Current
IDD
4.75
0.3
Power Dissipation
PD
1.5
5.25
V
1.1
mA
mW
TIMING CHARACTERISTICS
(VDD = +5V ± 5%, VREF = +2.5V, AGND = DGND = 0, CMOS inputs, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SCLK Frequency
SYMBOL
CONDITIONS
MIN
TYP
fSCLK
MAX
UNITS
10
MHz
SCLK Pulse Width High
tCH
45
ns
SCLK Pulse Width Low
tCL
45
ns
tCSS0
45
ns
45
ns
30
ns
CS Low to SCLK High Setup
CS High to SCLK High Setup
tCSS1
SCLK High to CS Low Hold
tCSH0
SCLK High to CS High Hold
tCSH1
45
ns
DIN to SCLK High Setup
tDS
40
ns
DIN to SCLK High Hold
tDH
0
ns
(Note 6)
LDAC Pulse Width
tLDAC
MAX545
50
ns
CS High to LDAC Low Setup
tLDACS
MAX545 (Note 6)
50
ns
VDD High to CS Low
(power-up delay)
Note 1:
Note 2:
Note 3:
Note 4:
Note 5:
Note 6:
20
µs
Gain Error tested at VREF = 2.0V, 2.5V, and 3.0V.
ROUT tolerance is typically ±20%.
Min/max range guaranteed by gain-error test. Operation outside min/max limits will result in degraded performance.
Reference input resistance is code dependent, minimum at 8554 hex.
Slew-rate value is measured from 0% to 63%.
Guaranteed by design. Not production tested.
_______________________________________________________________________________________
3
Typical Operating Characteristics
(VDD = 5V, VREF = +2.5V, TA = +25°C, unless otherwise noted.)
SUPPLY CURRENT
vs. REFERENCE VOLTAGE
0.40
0.35
0.30
0.33
0.32
0.31
0.30
0.29
0.28
0.27
0.25
0.20
0.15
0.26
0.25
0.20
-20
0
20
40
60
80
0.05
0
-0.05
-0.10
-0.15
-0.20
0
100
0.10
1
2
3
4
5
6
-60
-20
REFERENCE VOLTAGE (V)
TEMPERATURE (°C)
DIFFERENTIAL NONLINEARITY
vs. TEMPERATURE
INTEGRAL NONLINEARITY
vs. TEMPERATURE
0.20
0.20
60
100
140
100
140
16k
20k
GAIN ERROR
vs. TEMPERATURE
0.20
MAX544/MAX545-05
0.30
MAX544/MAX545-04
0.30
20
TEMPERATURE (°C)
MAX544/MAX545-06
-40
MAX544/MAX545-03
MAX544/MAX545-02
0.34
SUPPLY CURRENT (mA)
0.45
SUPPLY CURRENT (mA)
0.35
MAX544/MAX545-01
0.50
ZERO-CODE OFFSET ERROR
vs. TEMPERATURE
ZERO-CODE OFFSET ERROR (LSB)
SUPPLY CURRENT
vs. TEMPERATURE
0.15
+INL
DNL (LSB)
0
0
-DNL
-0.10
-0.10
-0.20
20
60
100
-0.20
-60
140
-20
20
60
100
TEMPERATURE (°C)
INTEGRAL NONLINEARITY
vs. CODE
DIFFERENTIAL NONLINEARITY
vs. CODE
MAX544/MAX545-07
0.250
0
-0.125
-0.125
-0.250
10k
DAC CODE
15k
20k
60
160
120
80
40
0
-0.250
5k
20
200
REFERENCE CURRENT (µA)
DNL (LSB)
0
-20
REFERENCE CURRENT
vs. CODE
0.125
0.125
-60
140
TEMPERATURE (°C)
TEMPERATURE (°C)
0.250
0
-0.05
MAX544/MAX545-09
-20
0
-0.15
-0.30
-0.30
-60
0.05
-0.10
-INL
-0.20
4
+DNL
MAX544/MAX545-08
INL (LSB)
0.10
GAIN ERROR (LSB)
0.10
0.10
INL (LSB)
MAX544/MAX545
+5V, Serial-Input, Voltage-Output, 14-Bit DACs
0
5k
10k
DAC CODE
15k
20k
0
4k
8k
12k
DAC CODE
_______________________________________________________________________________________
+5V, Serial-Input, Voltage-Output, 14-Bit DACs
MAX544-10
CL = 10pF
RL = ∞
CL = 10pF
RL = ∞
OUT
500mV/div
OUT
500mV/div
2µs/div
1µs/div
2µs/div
400ns/div
MAJOR-CARRY OUTPUT GLITCH
DIGITAL FEEDTHROUGH
2µs/div
MAX544-10A
FULL-SCALE STEP RESPONSE
(fSCLK = 20MHz)
FULL-SCALE STEP RESPONSE
(fSCLK = 10MHz)
CS
(5V/div)
SCLK
5V/div
OUT
(AC-COUPLED,
100mV/div)
OUT
(AC-COUPLED,
50mV/div)
MAX544/MAX545-11
CODE = 0000 hex
MAX544/MAX545-12
2µs/div
Pin Descriptions
MAX544
PIN
NAME
1
OUT
2
AGND
3
REF
Voltage Reference Input. Connect to external +2.5V reference.
4
CS
Chip-Select Input
5
SCLK
6
DIN
7
DGND
8
VDD
FUNCTION
DAC Output Voltage
Analog Ground
Serial-Clock Input. Duty cycle must be between 40% and 60%.
Serial-Data Input
Digital Ground
+5V Supply Voltage
_______________________________________________________________________________________
5
MAX544/MAX545
Typical Operating Characteristics (continued)
(VDD = +5V, VREF = +2.5V, TA = +25°C, unless otherwise noted.)
MAX544/MAX545
+5V, Serial-Input, Voltage-Output, 14-Bit DACs
Pin Descriptions (continued)
MAX545
PIN
NAME
FUNCTION
1
RFB
Feedback Resistor. Connect to external op amp’s output in bipolar mode.
2
OUT
DAC Output Voltage
3
AGNDF
Analog Ground (force)
4
AGNDS
Analog Ground (sense)
5
REFS
Voltage Reference Input (sense). Connect REFS to external +2.5V reference.
6
REFF
Voltage Reference Input (force). Connect REFF to external +2.5V reference.
7
CS
8
SCLK
Serial-Clock Input. Duty cycle must be between 40% and 60%.
9
N.C.
No Connection. Not internally connected.
10
DIN
Serial-Data Input
11
LDAC
LDAC Input. A falling edge updates the internal DAC latch.
12
DGND
Digital Ground
13
INV
Junction of internal scaling resistors. Connect to external op amp’s inverting input in
bipolar mode.
14
VDD
+5V Supply Voltage
Chip-Select Input
;;;;;;;;;
;;
;;;;;;
tCSH1
tLDACS
CS
tCSHO
tCSSO
tCH
tCSS1
tCL
SCLK
tDH
tDS
DIN
D13
D12
S0
LDAC*
tLDAC
*MAX545 ONLY
Figure 1. Timing Diagram
6
_______________________________________________________________________________________
+5V, Serial-Input, Voltage-Output, 14-Bit DACs
+2.5V
MAX544/MAX545
+5V
10µF
0.1µF
0.1µF
MC68XXXX
VDD
PCS0
CS
MOSI
DIN
SCLK
SCLK
(REFS)
UNIPOLAR
OUT
MAX495
OUT
MAX544/MAX545
(LDAC)
(GND)
REF (REFF)
DGND
EXTERNAL OP AMP
AGND_
( ) ARE FOR MAX545 ONLY
Figure 2a. Typical Operating Circuit—Unipolar Output
+5V
+2.5V
10µF
0.1µF
0.1µF
+5V
MC68XXXX
VDD
PCS0
CS
MOSI
DIN
SCLK
SCLK
IC1
LDAC
REFF
RFB
REFS
RINV
RFB
INV
MAX400
OUT
BIPOLAR
OUT
EXTERNAL OP AMP
MAX545
-5V
(GND)
DGND
AGNDF
AGNDS
Figure 2b. Typical Operating Circuit—Bipolar Output
Detailed Description
The MAX544/MAX545 voltage-output, 14-bit digital-toanalog converters (DACs) offer full 14-bit performance
with less than 0.5LSB integral linearity error and less
than 0.9LSB differential linearity error, thus ensuring
monotonic performance. Serial-data transfer minimizes
the number of package pins required.
The MAX544/MAX545 are composed of two matched
DAC sections, with an inverted R-2R DAC forming the
LSBs and the four MSBs derived from 15 identically
matched resistors. This architecture allows the lowest
glitch energy to be transferred to the DAC output on
major-carry transitions. It also lowers the DAC output
impedance by a factor of eight compared to a standard
R-2R ladder, allowing unbuffered operation in mediumload applications.
The MAX545 provides matched bipolar offset resistors,
which connect to an external op amp for bipolar output
swings (Figure 2b). For optimum performance, the
MAX545 also provides a set of Kelvin connections to
the voltage-reference and analog-ground inputs.
_______________________________________________________________________________________
7
MAX544/MAX545
+5V, Serial-Input, Voltage-Output, 14-Bit DACs
Digital Interface
External Reference
The MAX544/MAX545’s digital interface is a standard
3-wire connection compatible with SPI/QSPI/
MICROWIRE interfaces. The chip-select input (CS)
frames the serial data loading at the data-input pin
(DIN). Immediately following CS’s high-to-low transition,
the data is shifted synchronously and latched into the
input register on the rising edge of the serial clock input
(SCLK). After 16 bits (14 data bits, plus 2 sub-bits set to
zero) have been loaded into the serial input register, it
transfers its contents to the DAC latch on CS’s low-tohigh transition (Figure 3a). Note that if CS is not kept
low during the entire 16 SCLK cycles, data will be corrupted. In this case, reload the DAC latch with a new
16-bit word.
Alternatively, for the MAX545, LDAC allows the DAC
latch to update asynchronously by pulling LDAC low
after CS goes high (Figure 3b). Hold LDAC high during
the data-loading sequence.
The MAX544/MAX545 operate with external voltage references from 2V to 3V. The reference voltage determines the DAC’s full-scale output voltage. Kelvin
connections are provided with the MAX545 for optimum
performance. The 2.5V MAX873A, with ±15mV initial
accuracy and a 7ppm/°C (max) temperature coefficient, is a good choice.
Power-On Reset
The MAX544/MAX545 have a power-on reset circuit to
set the DAC’s output to 0V in unipolar mode when VDD
is first applied. This ensures that unwanted DAC output
voltages will not occur immediately following a system
power-up, such as after a loss of power. In bipolar
mode, the DAC output is set to -VREF.
; ; ;;
;;;
;;;
CS
DAC
UPDATED
SCLK
SUB-BITS
DIN
D13 D12 D11 D10 D9 D8 D7 D6
MSB
D5 D4 D3 D2 D1 D0 S1 S0
LSB
Figure 3a. MAX544/MAX545 3-Wire Interface Timing Diagram (LDAC = DGND for MAX545)
CS
SCLK
SUB-BITS
DIN
D13 D12 D11 D10 D9 D8 D7 D6
MSB
D5 D4 D3 D2 D1 D0 S1
S0
LSB
LDAC
DAC
UPDATED
Figure 3b. MAX545 4-Wire Interface Timing Diagram
8
_______________________________________________________________________________________
+5V, Serial-Input, Voltage-Output, 14-Bit DACs
Reference and Analog Ground Inputs
The MAX544/MAX545 operate with external voltage references from 2V to 3V, and maintain 14-bit performance
if certain guidelines are followed when selecting and
applying the reference. Ideally, the reference’s
temperature coefficient should be less than 1.5ppm/°C to
maintain 14-bit accuracy to within 1LSB over the 0°C to
+70°C commercial temperature range. Since this converter is designed as an inverted R-2R voltage-mode DAC,
the input resistance seen by the voltage reference is code
dependent. The worst-case input-resistance variation is
from 11.5kΩ (at code 8554 hex) to 200kΩ (at code 0000
hex). The maximum change in load current for a +2.5V
reference is +2.5V / 11.5kΩ = 217µA; therefore, the
required load regulation is 28ppm/mA for a maximum
error of 0.1LSB. This implies a reference output impedance of less than 71mΩ. In addition, the signal-path
impedance from the voltage reference to the reference
input must be kept low because it contributes directly to
the load-regulation error.
The requirement for a low-impedance voltage reference
is met with capacitor bypassing at the reference inputs
and ground. A 0.1µF ceramic capacitor with short leads
between REFF and AGNDF (MAX545), or REF and
AGND (MAX544), provides high-frequency bypassing.
A surface-mount ceramic chip capacitor is preferred
because it has the lowest inductance. An additional
10µF between REFF and AGNDF (MAX545), or REF
and AGND (MAX544), provides low-frequency bypassing. A low-ESR tantalum, film, or organic semiconductor
capacitor works well. Leaded capacitors are acceptable because impedance is not as critical at lower frequencies. The circuit can benefit from even larger
bypassing capacitors, depending on the stability of the
external reference with capacitive loading. If separate
force and sense lines are not used, tie the appropriate
force and sense pins together close to the package.
AGND must also be low impedance, as load-regulation
errors will be introduced by excessive AGND resistance. As in all high-resolution, high-accuracy applications, separate analog and digital ground planes yield
the best results. Tie DGND to AGND at the AGND pin to
form the “star” ground for the DAC system. Always refer
remote DAC loads to this system ground for the best
possible performance.
Unbuffered Operation
Unbuffered operation reduces power consumption as
well as offset error contributed by the external output
buffer. The R-2R DAC output is available directly at
OUT, allowing 14-bit performance from +VREF to AGND
without degradation at zero scale. The DAC’s output
impedance is also low enough to drive medium loads
(RL > 60kΩ) without degradation of INL or DNL; only
the gain error is increased by externally loading the
DAC output.
External Output Buffer Amplifier
The requirements on the external output buffer amplifier
change whether the DAC is used in unipolar or bipolar
operational mode. In unipolar mode, the output amplifier is used in a voltage-follower connection. In bipolar
mode (MAX545 only), the amplifier operates with the
internal scaling resistors (Figure 2b). In each mode, the
DAC’s output resistance is constant and is independent
of input code; however, the output amplifier’s input
impedance should still be as high as possible to minimize gain errors. The DAC’s output capacitance is also
independent of input code, thus simplifying stability
requirements on the external amplifier.
In bipolar mode, a precision amplifier operating with
dual power supplies (such as the MAX400) provides
the ±VREF output range. In single-supply applications,
precision amplifiers with input common-mode ranges
including AGND are available; however, their output
swings do not normally include the negative rail
(AGND) without significant degradation of performance.
A single-supply op amp, such as the MAX495, is suitable if the application does not use codes near zero.
Since the LSBs for a 14-bit DAC are extremely small
(152.6µV for VREF = 2.5V), pay close attention to the
external amplifier’s input specification. The input offset
voltage can degrade the zero-scale error and might
require an output offset trim to maintain full accuracy if
the offset voltage is greater than 1/2LSB. Similarly, the
input bias current multiplied by the DAC output resistance (typically 6.25kΩ) contributes to zero-scale error.
Temperature effects also must be taken into consideration. Over the 0°C to +70°C commercial temperature
range, the offset voltage temperature coefficient (referenced to +25°C) must be less than 1.7µV/°C to add
less than 1/2LSB of zero-scale error. The external
_______________________________________________________________________________________
9
MAX544/MAX545
Applications Information
MAX544/MAX545
+5V, Serial-Input, Voltage-Output, 14-Bit DACs
amplifier’s input resistance forms a resistive divider with
the DAC output resistance, which results in a gain
error. To contribute less than 1/2LSB of gain error, the
input resistance typically must be greater than:
1 1 
6.25kΩ ÷ 
 = 205MΩ
2  214 
The settling time is affected by the buffer input capacitance, the DAC’s output capacitance, and PC board
capacitance. The typical DAC output voltage settling
time is 1µs for a full-scale step. Settling time can be
significantly less for smaller step changes. Assuming a
single time-constant exponential settling response, a
full-scale step takes 10.4 time constants to settle to
within 1/2LSB of the final output voltage. The time constant is equal to the DAC output resistance multiplied
by the total output capacitance. The DAC output
capacitance is typically 10pF. Any additional output
capacitance increases the settling time.
The external buffer amplifier’s gain-bandwidth product
is important because it increases the settling time by
adding another time constant to the output response.
The effective time constant of two cascaded systems,
each with a single time-constant response, is approximately the root square sum of the two time constants.
The DAC output’s time constant is 1µs / 10.4 = 96ns,
ignoring the effect of additional capacitance. If the time
constant of an external amplifier with 1MHz bandwidth
is 1 / 2π (1MHz) = 159ns, then the effective time constant of the combined system is:
 96ns 2 + 159ns 2  = 186ns
) (
) 
(
This suggests that the settling time to within 1/2LSB of
the final output voltage, including the external buffer
amplifier, will be approximately 10.4 · 186ns = 1.93µs.
Digital Inputs and Interface Logic
The digital interface for the 14-bit DAC is based on a
3-wire standard that is compatible with SPI, QSPI, and
MICROWIRE interfaces. The three digital inputs (CS,
DIN, and SCLK) load the digital input data serially into
the DAC. LDAC (MAX545) updates the DAC output
asynchronously.
All of the digital inputs include Schmitt-trigger buffers to
accept slow-transition interfaces. This means that optocouplers can interface directly to the MAX544/MAX545
without additional external logic. The digital inputs are
compatible with TTL/CMOS-logic levels.
Unipolar Configuration
Figure 2a shows the MAX544/MAX545 configured for
unipolar operation with an external op amp. The op amp
is set for unity gain, and Table 1 lists the codes for this
circuit.
Bipolar Configuration
Figure 2b shows the MAX545 configured for bipolar
operation with an external op amp. The op amp is set
for unity gain with an offset of -1/2VREF. Table 2 shows
the offset binary codes for this circuit.
Power-Supply Bypassing and
Ground Management
For optimum system performance, use PC boards with
separate analog and digital ground planes. Wire-wrap
boards are not recommended. Connect the two ground
planes together at the low-impedance power-supply
source. Connect DGND and AGND together at the IC.
The best ground connection can be achieved by connecting the DAC’s DGND and AGND pins together and
connecting that point to the system analog ground
plane. If the DAC’s DGND is connected to the system
digital ground, digital noise may get through to the
DAC’s analog portion.
Bypass VDD with a 0.1µF ceramic capacitor connected
between V DD and AGND. Mount it with short leads
close to the device. Ferrite beads can also be used to
further isolate the analog and digital power supplies.
Table 1. Unipolar Code Table
DAC LATCH CONTENTS
MSB
ANALOG OUTPUT, VOUT
LSB
1000 0000 0000 00(00)
VREF · (16,383 / 16,384)
VREF · (8192 / 16,384) = 1/2VREF
0000 0000 0000 01(00)
VREF · (1 / 16,384)
0000 0000 0000 00(00)
0V
1111 1111 1111 11(00)
Table 2. Bipolar Code Table
DAC LATCH CONTENTS
MSB
ANALOG OUTPUT, VOUT
LSB
1111 1111 1111 11(00)
+VREF · (8191 / 8192)
1000 0000 0000 01(00)
+VREF · (1 / 8192)
1000 0000 0000 00(00)
0V
0111 1111 1111 11(00)
-VREF · (1 / 8192)
0000 0000 0000 00(00)
-VREF · (8192 / 8192) = -VREF
( ) = Sub-bits
10
______________________________________________________________________________________
+5V, Serial-Input, Voltage-Output, 14-Bit DACs
Functional Diagrams (continued)
INL
(LSB)
PART
TEMP. RANGE
PIN-PACKAGE
MAX544AEPA
-40°C to +85°C
8 Plastic DIP
MAX544BEPA
-40°C to +85°C
8 Plastic DIP
MAX544AESA
-40°C to +85°C
8 SO
±1/2
MAX544BESA
-40°C to +85°C
8 SO
±1
MAX545ACPD
0°C to +70°C
14 Plastic DIP
±1/2
MAX545BCPD
0°C to +70°C
14 Plastic DIP
±1
MAX545ACSD
0°C to +70°C
14 SO
±1/2
MAX545BCSD
0°C to +70°C
14 SO
±1
MAX545AEPD
-40°C to +85°C
14 Plastic DIP
±1/2
MAX545BEPD
-40°C to +85°C
14 Plastic DIP
±1
MAX545AESD
-40°C to +85°C
14 SO
±1/2
MAX545BESD
-40°C to +85°C
14 SO
±1
MAX545BMJD
-55°C to +125°C
14 Ceramic SB*
±1
VDD
±1/2
±1
MAX544
REF
14-BIT DAC
CS
DIN
SCLK
DATA LATCH
OUT
AGND
CONTROL
LOGIC
SERIAL INPUT REGISTER
DGND
*Contact factory for availability.
Chip Information
TRANSISTOR COUNT: 2209
______________________________________________________________________________________
11
MAX544/MAX545
Ordering Information (continued)
SOICN.EPS
________________________________________________________Package Information
PDIPN.EPS
MAX544/MAX545
+5V, Serial-Input, Voltage-Output, 14-Bit DACs
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 1999 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
Similar pages