M 25AA040/25LC040/25C040 4K SPI™ Bus Serial EEPROM PACKAGE TYPES DEVICE SELECTION TABLE Part Number Max Clock Frequency 1.8-5.5V 1 MHz Temp Ranges PDIP/SOIC C,I CS 1 25LC040 2.5-5.5V 2 MHz C,I SO 2 25C040 4.5-5.5V 3 MHz C,I,E WP 3 VSS 4 FEATURES 8 VCC 7 HOLD 6 SCK 5 SI TSSOP HOLD VCC CS SO 1 2 3 4 25xx040 • Low power CMOS technology - Write current: 3 mA typical - Read current: 500 µA typical - Standby current: 500 nA typical • 512 x 8 bit organization • 16 byte page • Write cycle time: 5ms max. • Self-timed ERASE and WRITE cycles • Block write protection - Protect none, 1/4, 1/2, or all of array • Built-in write protection - Power on/off data protection circuitry - Write enable latch - Write protect pin • Sequential read • High reliability - Endurance: 1M cycles (guaranteed) - Data retention: > 200 years - ESD protection: > 4000 V • 8-pin PDIP, SOIC, and TSSOP packages • Temperature ranges supported: - Commercial (C): 0°C to +70°C - Industrial (I): -40°C to +85°C - Automotive (E) (25C040): -40°C to +125°C 25xx040 25AA040 VCC Range 8 7 6 5 SCK SI VSS WP BLOCK DIAGRAM Status Register HV Generator EEPROM I/O Control Logic Memory Control Logic X Array Dec Page Latches DESCRIPTION The Microchip Technology Inc. 25AA040/25LC040/ 25C040 (25xx040*) is a 4K bit serial Electrically Erasable PROM. The memory is accessed via a simple Serial Peripheral Interface (SPI) compatible serial bus. The bus signals required are a clock input (SCK) plus separate data in (SI) and data out (SO) lines. Access to the device is controlled through a chip select (CS) input. SI Y Decoder SO CS SCK Sense Amp. R/W Control HOLD WP VCC VSS Communication to the device can be paused via the hold pin (HOLD). While the device is paused, transitions on its inputs will be ignored, with the exception of chip select, allowing the host to service higher priority interrupts. Also, write operations to the device can be disabled via the write protect pin (WP). *25xx040 is used in this document as a generic part number for the 25AA040/25LC040/25C040 devices. SPI is a trademark of Motorola. 1998 Microchip Technology Inc. Powered by ICminer.com Electronic-Library Service CopyRight 2003 DS21204B-page 1 25AA040/25LC040/25C040 1.0 ELECTRICAL CHARACTERISTICS 1.1 FIGURE 1-2: AC TEST CIRCUIT VCC Maximum Ratings* 2.25 K Vcc ...................................................................................7.0V All inputs and outputs w.r.t. Vss.................. -0.6V to Vcc+1.0V Storage temperature ....................................... -65˚C to 150˚C Ambient temperature under bias..................... -65˚C to 125˚C Soldering temperature of leads (10 seconds) ............. +300˚C ESD protection on all pins.................................................4kV SO 1.8 K *Notice: Stresses above those listed under ‘Maximum ratings’ may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for an extended period of time may affect device reliability 1.2 100 pF AC Test Conditions AC Waveform: TABLE 1-1: VLO = 0.2V PIN FUNCTION TABLE Name Function VH I = VCC - 0.2V (Note 1) VH I = 4.0V (Note 2) CS Chip Select Input SO Serial Data Output Input 0.5 VCC SI Serial Data Input Output 0.5 VCC SCK Serial Clock Input WP Write Protect Pin VSS Ground VCC Supply Voltage HOLD Timing Measurement Reference Level Note 1: For VCC ≤ 4.0V 2: For VCC > 4.0V Hold Input TABLE 1-3: DC CHARACTERISTICS All parameters apply over the specified operating ranges unless otherwise noted. Parameter High level input voltage Low level input voltage Commercial (C): TAMB = 0°C to +70°C Industrial (I): TAMB = -40°C to +85°C Automotive (E): TAMB = -40°C to +125°C Symbol Min VCC = 1.8V to 5.5V VCC = 1.8V to 5.5V VCC = 4.5V to 5.5V (25C040 only) Max Units Test Conditions VIH1 2.0 VCC+1 V VCC ≥ 2.7V (Note) VIH2 0.7 VCC VCC+1 V VCC< 2.7V (Note) VIL1 -0.3 0.8 V VCC ≥ 2.7V (Note) VIL2 -0.3 0.3 VCC V VCC < 2.7V (Note) VOL — 0.4 V IOL = 2.1 mA VOL — 0.2 V IOL = 1.0 mA, VCC < 2.5V VOH VCC -0.5 — V IOH =-400 µA ILI -10 10 µA CS = VCC, VIN = VSS TO VCC Output leakage current ILO -10 10 µA CS = VCC, VOUT = VSS TO VCC Internal Capacitance (all inputs and outputs) CINT — 7 pF TAMB = 25˚C, CLK = 1.0 MHz, VCC = 5.0V (Note) ICC Read — — 1 500 mA µA VCC = 5.5V; FCLK=3.0 MHz; SO = Open VCC = 2.5V; FCLK=2.0 MHz; SO = Open ICC Write — — 5 3 mA mA VCC= 5.5V VCC = 2.5V ICCS — — 5 2 µA µA CS = Vcc = 5.5V, Inputs tied to VCC or VSS CS = Vcc = 2.5V, Inputs tied to VCC or VSS Low level output voltage High level output voltage Input leakage current Operating Current Standby Current Note: This parameter is periodically sampled and not 100% tested. DS21204B-page 2 Powered by ICminer.com Electronic-Library Service CopyRight 2003 1998 Microchip Technology Inc. 25AA040/25LC040/25C040 TABLE 1-4: AC CHARACTERISTICS All parameters apply over the specified operating ranges unless otherwise noted. Parameter Commercial (C): Industrial (I): Automotive (E): Tamb = 0°C to +70°C Tamb = -40°C to +85°C Tamb = -40°C to +125°C VCC = 1.8V to 5.5V VCC = 1.8V to 5.5V VCC = 4.5V to 5.5V (25C040 only) Symbol Min Max Units Clock Frequency FCLK — — — 3 2 1 MHz MHz MHz VCC = 4.5V to 5.5V VCC = 2.5V to 4.5V VCC = 1.8V to 2.5V Test Conditions CS Setup Time TCSS 100 250 500 — — — ns ns ns VCC = 4.5V to 5.5V VCC = 2.5V to 4.5V VCC = 1.8V to 2.5V CS Hold Time TCSH 150 250 475 — — — ns ns ns VCC = 4.5V to 5.5V VCC = 2.5V to 4.5V VCC = 1.8V to 2.5V CS Disable Time TCSD 500 — ns Data Setup Time TSU 30 50 50 — — — ns ns ns VCC = 4.5V to 5.5V VCC = 2.5V to 4.5V VCC = 1.8V to 2.5V Data Hold Time THD 50 100 100 — — — ns ns ns VCC = 4.5V to 5.5V VCC = 2.5V to 4.5V VCC = 1.8V to 2.5V (Note 1) CLK Rise Time TR — 2 µs CLK Fall Time TF — 2 µs (Note 1) Clock High Time THI 150 250 475 — — — ns ns ns VCC = 4.5V to 5.5V VCC = 2.5V to 4.5V VCC = 1.8V to 2.5V Clock Low Time TLO 150 250 475 — — — ns ns ns VCC = 4.5V to 5.5V VCC = 2.5V to 4.5V VCC = 1.8V to 2.5V Clock Delay Time TCLD 50 — ns Clock Enable Time TCLE 50 — ns TV — — — 150 250 475 ns ns ns VCC = 4.5V to 5.5V VCC = 2.5V to 4.5V VCC = 1.8V to 2.5V Output Valid from Clock Low Output Hold Time THO 0 — ns (Note 1) Output Disable Time TDIS — — — 200 250 500 ns ns ns VCC = 4.5V to 5.5V (Note 1) VCC = 2.5V to 4.5V (Note 1) VCC = 1.8V to 2.5V (Note 1) HOLD Setup Time THS 100 100 200 — — — ns ns ns VCC = 4.5V to 5.5V VCC = 2.5V to 4.5V VCC = 1.8V to 2.5V HOLD Hold Time THH 100 100 200 — — — ns ns ns VCC = 4.5V to 5.5V VCC = 2.5V to 4.5V VCC = 1.8V to 2.5V HOLD Low to Output High-Z THZ 100 150 200 — — — ns ns ns VCC = 4.5V to 5.5V (Note 1) VCC = 2.5V to 4.5V (Note 1) VCC = 1.8V to 2.5V (Note 1) HOLD High to Output Valid THV 100 150 200 — — — ns ns ns VCC = 4.5V to 5.5V VCC = 2.5V to 4.5V VCC = 1.8V to 2.5V Internal Write Cycle Time TWC — 5 ms — 1M — E/W Cycles Endurance Note 1: 2: (Note 2) This parameter is periodically sampled and not 100% tested. This parameter is not tested but guaranteed by characterization. For endurance estimates in a specific application, please consult the Total Endurance Model which can be obtained on our website. 1998 Microchip Technology Inc. Powered by ICminer.com Electronic-Library Service CopyRight 2003 DS21204B-page 3 25AA040/25LC040/25C040 FIGURE 1-5: HOLD TIMING CS THS THH THS THH SCK THZ SO n+2 n+1 n THV high impedance n n-1 TSU n+2 SI n+1 n don’t care n n-1 HOLD FIGURE 1-6: SERIAL INPUT TIMING TCSD CS TCLE TCLD TR TCSS TF Mode 1,1 TCSH SCK Mode 0,0 Tsu THD SI MSB in high impedance SO FIGURE 1-7: LSB in SERIAL OUTPUT TIMING CS TCSH THI TLO Mode 1,1 SCK Mode 0,0 TV THC SO SI MSB out TDIS ISB out don’t care DS21204B-page 4 Powered by ICminer.com Electronic-Library Service CopyRight 2003 1998 Microchip Technology Inc. 25AA040/25LC040/25C040 2.0 PIN DESCRIPTIONS 2.5 2.1 Chip Select (CS) This pin is a hardware write protect input pin. When WP is low, all writes to the array or status register are disabled, but any other operation functions normally. When WP is high, all functions, including non-volatile writes operate normally. WP going low at any time will reset the write enable latch and inhibit programming, except when an internal write has already begun. If an internal write cycle has already begun, WP going low will have no effect on the write. See Table 3-7 for Write Protect Functionality Matrix. A low level on this pin selects the device. A high level deselects the device and forces it into standby mode. However, a programming cycle which is already initiated or in progress will be completed, regardless of the CS input signal. If CS is brought high during a program cycle, the device will go in standby mode as soon as the programming cycle is complete. As soon as the device is deselected, SO goes to the high impedance state, allowing multiple parts to share the same SPI bus. A low to high transition on CS after a valid write sequence initiates an internal write cycle. After power-up, a low level on CS is required prior to any sequence being initiated. 2.2 Serial Input (SI) The SI pin is used to transfer data into the device. It receives instructions, addresses, and data. Data is latched on the rising edge of the serial clock. 2.3 Serial Output (SO) The SO pin is used to transfer data out of the 25xx040. During a read cycle, data is shifted out on this pin after the falling edge of the serial clock. 2.4 Serial Clock (SCK) The SCK is used to synchronize the communication between a master and the 25xx040. Instructions, addresses, or data present on the SI pin are latched on the rising edge of the clock input, while data on the SO pin is updated after the falling edge of the clock input. 1998 Microchip Technology Inc. Powered by ICminer.com Electronic-Library Service CopyRight 2003 2.6 Write Protect (WP) Hold (HOLD) The HOLD pin is used to suspend transmission to the 25xx040 while in the middle of a serial sequence without having to re-transmit the entire sequence over at a later time. It must be held high any time this function is not being used. Once the device is selected and a serial sequence is underway, the HOLD pin may be pulled low to pause further serial communication without resetting the serial sequence. The HOLD pin must be brought low while SCK is low, otherwise the HOLD function will not be invoked until the next SCK high to low transition. The 25xx040 must remain selected during this sequence. The SI, SCK, and SO pins are in a high impedance state during the time the part is paused and transitions on these pins will be ignored. To resume serial communication, HOLD must be brought high while the SCK pin is low, otherwise serial communication will not resume. Lowering the HOLD line at any time will tri-state the SO line. DS21204B-page 5 25AA040/25LC040/25C040 3.0 FUNCTIONAL DESCRIPTION 3.3 3.1 PRINCIPLES OF OPERATION Prior to any attempt to write data to the 25xx040, the write enable latch must be set by issuing the WREN instruction (Figure 3-5). This is done by setting CS low and then clocking out the proper instruction into the 25xx040. After all eight bits of the instruction are transmitted, the CS must be brought high to set the write enable latch. If the write operation is initiated immediately after the WREN instruction without CS being brought high, the data will not be written to the array because the write enable latch will not have been properly set. The 25xx040 is a 512 byte Serial EEPROM designed to interface directly with the Serial Peripheral Interface (SPI) port of many of today’s popular microcontroller families, including Microchip’s PIC16C6X/7X microcontrollers. It may also interface with microcontrollers that do not have a built-in SPI port by using discrete I/O lines programmed properly with the software. The 25xx040 contains an 8-bit instruction register. The part is accessed via the SI pin, with data being clocked in on the rising edge of SCK. The CS pin must be low and the HOLD pin must be high for the entire operation. The WP pin must be held high to allow writing to the memory array. Table 3-1 contains a list of the possible instruction bytes and format for device operation. The most significant address bit (A8) is located in the instruction byte. All instructions, addresses, and data are transferred MSB first, LSB last. Data is sampled on the first rising edge of SCK after CS goes low. If the clock line is shared with other peripheral devices on the SPI bus, the user can assert the HOLD input and place the 25xx040 in ‘HOLD’ mode. After releasing the HOLD pin, operation will resume from the point when the HOLD was asserted. 3.2 Read Sequence The part is selected by pulling CS low. The 8-bit read instruction with the A8 address bit is transmitted to the 25xx040 followed by the lower 8-bit address (A7 through A0). After the correct read instruction and address are sent, the data stored in the memory at the selected address is shifted out on the SO pin. The data stored in the memory at the next address can be read sequentially by continuing to provide clock pulses. The internal address pointer is automatically incremented to the next higher address after each byte of data is shifted out. When the highest address is reached (01FFh), the address counter rolls over to address 0000h allowing the read cycle to be continued indefinitely. The read operation is terminated by raising the CS pin (Figure 3-2). TABLE 3-1: Write Sequence Once the write enable latch is set, the user may proceed by setting the CS low, issuing a write instruction, followed by the address, and then the data to be written. Keep in mind that the most significant address bit (A8) is included in the instruction byte. Up to 16 bytes of data can be sent to the 25xx040 before a write cycle is necessary. The only restriction is that all of the bytes must reside in the same page. A page address begins with XXXX 0000 and ends with XXXX 1111. If the internal address counter reaches XXXX 1111 and the clock continues, the counter will roll back to the first address of the page and overwrite any data in the page that may have been written. For the data to be actually written to the array, the CS must be brought high after the least significant bit (D0) of the nth data byte has been clocked in. If CS is brought high at any other time, the write operation will not be completed. Refer to Figure 3-3 and Figure 3-4 for more detailed illustrations on the byte write sequence and the page write sequence respectively. While the write is in progress, the status register may be read to check the status of the WIP, WEL, BP1, and BP0 bits (Figure 3-8). A read attempt of a memory array location will not be possible during a write cycle. When the write cycle is completed, the write enable latch is reset. INSTRUCTION SET Instruction Name Instruction Format READ 0000 A8011 Read data from memory array beginning at selected address WRITE 0000 A8010 Write data to memory array beginning at selected address WRDI 0000 0100 Reset the write enable latch (disable write operations) WREN 0000 0110 Set the write enable latch (enable write operations) RDSR 0000 0101 Read status register WRSR 0000 0001 Write status register Note: A8 is the 9th Description address bit necessary to fully address 512 bytes. DS21204B-page 6 Powered by ICminer.com Electronic-Library Service CopyRight 2003 1998 Microchip Technology Inc. 25AA040/25LC040/25C040 FIGURE 3-2: READ SEQUENCE CS 0 1 2 3 4 5 6 7 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 8 SCK instruction 0 SI 0 0 0 lower address byte A8 0 1 A7 1 6 5 3 4 2 1 A0 don’t care data out high impedance 7 SO FIGURE 3-3: 6 5 4 3 2 1 0 BYTE WRITE SEQUENCE CS twc 0 1 2 3 4 5 6 7 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 8 SCK instruction SI 0 0 0 0 A8 data byte lower address byte 0 1 0 A7 6 5 3 4 2 A0 7 1 6 5 4 3 2 1 0 high impedance SO FIGURE 3-4: PAGE WRITE SEQUENCE CS 0 1 2 3 4 5 6 7 8 9 10 11 13 14 15 16 17 18 19 20 21 22 23 24 SCK instruction SI 0 0 0 0 A8 lower address byte 0 1 0 A7 6 5 3 4 2 data byte 1 1 0 7 6 5 4 7 6 3 2 1 0 CS 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 SCK data byte 2 SI 7 6 5 4 3 data byte 3 2 1 0 7 6 1998 Microchip Technology Inc. Powered by ICminer.com Electronic-Library Service CopyRight 2003 5 4 3 data byte n (16 max) 2 1 0 5 4 3 2 1 0 DS21204B-page 7 25AA040/25LC040/25C040 3.4 Write Enable (WREN) and Write Disable (WRDI) The following is a list of conditions under which the write enable latch will be reset: • • • • • The 25xx040 contains a write enable latch. See Table 3-10 for the Write Protect Functionality Matrix. This latch must be set before any write operation will be completed internally. The WREN instruction will set the latch, and the WRDI will reset the latch. FIGURE 3-5: Power-up WRDI instruction successfully executed WRSR instruction successfully executed WRITE instruction successfully executed WP line is low WRITE ENABLE SEQUENCE CS 0 1 2 3 4 5 6 7 SCK SI 0 0 0 0 0 1 1 0 high impedance SO FIGURE 3-6: WRITE DISABLE SEQUENCE CS 0 1 2 3 4 5 6 7 SCK SI 0 0 0 0 0 1 10 0 high impedance SO DS21204B-page 8 Powered by ICminer.com Electronic-Library Service CopyRight 2003 1998 Microchip Technology Inc. 25AA040/25LC040/25C040 3.5 Read Status Register (RDSR) 3.6 The RDSR instruction provides access to the status register. The status register may be read at any time, even during a write cycle. The status register is formatted as follows: 7 X 6 X 5 X 4 X 3 BP1 2 BP0 1 WEL Write Status Register(WRSR) The WRSR instruction allows the user to select one of four levels of protection for the array by writing to the appropriate bits in the status register. The array is divided up into four segments. The user has the ability to write protect none, one, two, or all four of the segments of the array. The partitioning is controlled as illustrated in Table 3-7. 0 WIP The Write-In-Process (WIP) bit indicates whether the 25xx040 is busy with a write operation. When set to a ‘1’ a write is in progress, when set to a ‘0’ no write is in progress. This bit is read only. See Figure 3-9 for WRSR timing sequence TABLE 3-7: The Write Enable Latch (WEL) bit indicates the status of the write enable latch. When set to a ‘1’ the latch allows writes to the array, when set to a ‘0’ the latch prohibits writes to the array. The state of this bit can always be updated via the WREN or WRDI commands regardless of the state of write protection on the status register. This bit is read only. ARRAY PROTECTION Array Addresses Write Protected BP1 BP0 0 0 none 0 1 upper 1/4 (0180h - 01FFh) 1 0 upper 1/2 (0100h - 01FFh) 1 1 all (0000h - 01FFh) The Block Protection (BP0 and BP1) bits indicate which blocks are currently write protected. These bits are set by the user issuing the WRSR instruction. These bits are non-volatile. See Figure 3-8 for RDSR timing sequence FIGURE 3-8: READ STATUS REGISTER SEQUENCE CS 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 SCK instruction SI 0 0 0 0 0 1 0 1 data from status register high impedance 7 SO FIGURE 3-9: 6 5 4 3 2 1 0 WRITE STATUS REGISTER SEQUENCE CS 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 0 SCK instruction SI 0 0 0 0 0 data to status register 0 0 1 7 6 5 4 3 2 high impedance SO 1998 Microchip Technology Inc. Powered by ICminer.com Electronic-Library Service CopyRight 2003 DS21204B-page 9 25AA040/25LC040/25C040 3.7 Data Protection 3.8 The following protection has been implemented to prevent inadvertent writes to the array: • The write enable latch is reset on power-up. • A write enable instruction must be issued to set the write enable latch. • After a byte write, page write, or status register write, the write enable latch is reset. • CS must be set high after the proper number of clock cycles to start an internal write cycle. • Access to the array during an internal write cycle is ignored and programming is continued. • The write enable latch is reset when the WP pin is low. TABLE 3-10: Power On State The 25xx040 powers on in the following state: • The device is in low power standby mode (CS = 1). • The write enable latch is reset. • SO is in high impedance state. • A low level on CS is required to enter active state. . WRITE PROTECT FUNCTIONALITY MATRIX WP WEL Protected Blocks Unprotected Blocks Status Register Low X Protected Protected Protected High 0 Protected Protected Protected High 1 Protected Writable Writable DS21204B-page 10 Powered by ICminer.com Electronic-Library Service CopyRight 2003 1998 Microchip Technology Inc. 25AA040/25LC040/25C040 25AA040/25LC040/25C040 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. 25xx040 — /P P = Plastic DIP (300 mil Body), 8-lead SN = Plastic SOIC (150 mil Body), 8-lead ST = TSSOP, 8-lead Package: Temperature Range: Blank = 0°C to +70°C I = –40°C to +85°C E = –40°C to +125°C 25AA040 25AA040T 25AA040X 25AA040XT Devices: 25LC040 25LC040T 25LC040X 25LC040XT 25C040 25C040T 25C040X 25C040XT 4096 bit 1.8V SPI Serial EEPROM 4096 bit 1.8V SPI Serial EEPROM Tape and Reel 4096 bit 1.8V SPI Serial EEPROM in alternate pinout (ST only) 4096 bit 1.8V SPI Serial EEPROM in alternate pinout Tape and Reel (ST only) 4096 bit 2.5V SPI Serial EEPROM 4096 bit 2.5V SPI Serial EEPROM Tape and Reel 4096 bit 2.5V SPI Serial EEPROM in alternate pinout (ST only) 4096 bit 2.5V SPI Serial EEPROM in alternate pinout Tape and Reel (ST only) 4096 bit 5.0V SPI Serial EEPROM 4096 bit 5.0V SPI Serial EEPROM Tape and Reel 4096 bit 5.0V SPI Serial EEPROM in alternate pinout (ST only) 4096 bit 5.0V SPI Serial EEPROM in alternate pinout Tape and Reel (ST only) Sales and Support Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. Your local Microchip sales office 2. The Microchip Corporate Literature Center U.S. FAX: (602) 786-7277 3. The Microchip Worldwide Web Site (www.microchip.com) 1998 Microchip Technology Inc. Powered by ICminer.com Electronic-Library Service CopyRight 2003 DS21204B-page 11 WORLDWIDE SALES AND SERVICE AMERICAS AMERICAS (continued) Corporate Office Toronto Singapore Microchip Technology Inc. 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-786-7200 Fax: 480-786-7277 Technical Support: 480-786-7627 Web Address: http://www.microchip.com Microchip Technology Inc. 5925 Airport Road, Suite 200 Mississauga, Ontario L4V 1W1, Canada Tel: 905-405-6279 Fax: 905-405-6253 Microchip Technology Singapore Pte Ltd. 200 Middle Road #07-02 Prime Centre Singapore 188980 Tel: 65-334-8870 Fax: 65-334-8850 Atlanta Microchip Asia Pacific Unit 2101, Tower 2 Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2-401-1200 Fax: 852-2-401-3431 Microchip Technology Inc. 500 Sugar Mill Road, Suite 200B Atlanta, GA 30350 Tel: 770-640-0034 Fax: 770-640-0307 Boston Microchip Technology Inc. 5 Mount Royal Avenue Marlborough, MA 01752 Tel: 508-480-9990 Fax: 508-480-8575 Chicago Microchip Technology Inc. 333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075 Dallas Microchip Technology Inc. 4570 Westgrove Drive, Suite 160 Addison, TX 75248 Tel: 972-818-7423 Fax: 972-818-2924 Dayton Microchip Technology Inc. Two Prestige Place, Suite 150 Miamisburg, OH 45342 Tel: 937-291-1654 Fax: 937-291-9175 Detroit Microchip Technology Inc. Tri-Atria Office Building 32255 Northwestern Highway, Suite 190 Farmington Hills, MI 48334 Tel: 248-538-2250 Fax: 248-538-2260 Los Angeles Microchip Technology Inc. 18201 Von Karman, Suite 1090 Irvine, CA 92612 Tel: 949-263-1888 Fax: 949-263-1338 New York Microchip Technology Inc. 150 Motor Parkway, Suite 202 Hauppauge, NY 11788 Tel: 631-273-5305 Fax: 631-273-5335 ASIA/PACIFIC Hong Kong ASIA/PACIFIC (continued) Taiwan, R.O.C Microchip Technology Taiwan 10F-1C 207 Tung Hua North Road Taipei, Taiwan, ROC Tel: 886-2-2717-7175 Fax: 886-2-2545-0139 EUROPE Beijing United Kingdom Microchip Technology, Beijing Unit 915, 6 Chaoyangmen Bei Dajie Dong Erhuan Road, Dongcheng District New China Hong Kong Manhattan Building Beijing 100027 PRC Tel: 86-10-85282100 Fax: 86-10-85282104 Arizona Microchip Technology Ltd. 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44 118 921 5858 Fax: 44-118 921-5835 India Denmark Microchip Technology Inc. India Liaison Office No. 6, Legacy, Convent Road Bangalore 560 025, India Tel: 91-80-229-0061 Fax: 91-80-229-0062 Microchip Technology Denmark ApS Regus Business Centre Lautrup hoj 1-3 Ballerup DK-2750 Denmark Tel: 45 4420 9895 Fax: 45 4420 9910 Japan France Microchip Technology Intl. Inc. Benex S-1 6F 3-18-20, Shinyokohama Kohoku-Ku, Yokohama-shi Kanagawa 222-0033 Japan Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Arizona Microchip Technology SARL Parc d’Activite du Moulin de Massy 43 Rue du Saule Trapu Batiment A - ler Etage 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Korea Germany Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea Tel: 82-2-554-7200 Fax: 82-2-558-5934 Arizona Microchip Technology GmbH Gustav-Heinemann-Ring 125 D-81739 München, Germany Tel: 49-89-627-144 0 Fax: 49-89-627-144-44 Shanghai Arizona Microchip Technology SRL Centro Direzionale Colleoni Palazzo Taurus 1 V. Le Colleoni 1 20041 Agrate Brianza Milan, Italy Tel: 39-039-65791-1 Fax: 39-039-6899883 Microchip Technology RM 406 Shanghai Golden Bridge Bldg. 2077 Yan’an Road West, Hong Qiao District Shanghai, PRC 200335 Tel: 86-21-6275-5700 Fax: 86 21-6275-5060 San Jose Microchip Technology Inc. 2107 North First Street, Suite 590 San Jose, CA 95131 Tel: 408-436-7950 Fax: 408-436-7955 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Italy 11/15/99 Microchip received QS-9000 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona in July 1999. The Company’s quality system processes and procedures are QS-9000 compliant for its PICmicro® 8-bit MCUs, KEELOQ® code hopping devices, Serial EEPROMs and microperipheral products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001 certified. All rights reserved. © 1999 Microchip Technology Incorporated. Printed in the USA. 11/99 Printed on recycled paper. Information contained in this publication regarding device applications and the like is intended for suggestion only and may be superseded by updates. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip’s products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. The Microchip logo and name are registered trademarks of Microchip Technology Inc. in the U.S.A. and other countries. All rights reserved. All other trademarks mentioned herein are the property of their respective companies. 1999 Microchip Technology Inc.