Maxim MAX993EUD+ Micropower, low-voltage, ucsp/sc70, rail-to-rail i/o comparator Datasheet

19-1229; Rev 5; 4/12
Micropower, Low-Voltage, UCSP/SC70,
Rail-to-Rail I/O Comparators
The MAX985/MAX986/MAX989/MAX990/MAX993/
MAX994 single/dual/quad micropower comparators
feature low-voltage operation and rail-to-rail inputs and
outputs. Their operating voltages range from 2.5V to
5.5V, making them ideal for both 3V and 5V systems.
These comparators also operate with ±1.25V to ±2.75V
dual supplies. They consume only 11µA of supply current while achieving a 300ns propagation delay.
Input bias current is typically 1.0pA, and input offset
voltage is typically 0.5mV. Internal hysteresis ensures
clean output switching, even with slow-moving input
signals.
The output stage’s unique design limits supply-current
surges while switching, virtually eliminating the supply
glitches typical of many other comparators. The
MAX985/MAX989/MAX993 have a push-pull output
stage that sinks as well as sources current. Large internal output drivers allow rail-to-rail output swing with
loads up to 8mA. The MAX986/MAX990/MAX994 have
an open-drain output stage that can be pulled beyond
VCC to 6V (max) above VEE. These open-drain versions
are ideal for level translators and bipolar to singleended converters.
The single MAX985 is available in a chip-scale package (UCSP™), significantly reducing the required PC
board area. The single MAX985/MAX986 are available
in 5-pin SC70 packages and the dual MAX989/MAX990
are available in 8-pin SOT23 packages.
Selector Guide
PART
COMPARATORS
PER PACKAGE
OUTPUT
STAGE
MAX985
1
Push-Pull
MAX986
1
Open-Drain
MAX989
2
Push-Pull
MAX990
2
Open-Drain
MAX993
4
Push-Pull
MAX994
4
Open-Drain
Applications
Portable/BatteryPowered Systems
Mobile Communications
Zero-Crossing Detectors
Window Comparators
Level Translators
Threshold Detectors/
Discriminators
Ground/Supply-Sensing
Applications
IR Receivers
Digital Line Receivers
UCSP is a trademark and µMAX is a registered trademark of
Maxim Integrated Products, Inc.
____________________________Features
o 11µA Quiescent Supply Current
o 2.5V to 5.5V Single-Supply Operation
o Common-Mode Input Voltage Range Extends
250mV Beyond the Rails
o 300ns Propagation Delay
o Push-Pull Output Stage Sinks and Sources
8mA Current (MAX985/MAX989/MAX993)
o Open-Drain Output Voltage Extends Beyond VCC
(MAX986/MAX990/MAX994)
o Unique Output Stage Reduces Output Switching
Current, Minimizing Overall Power Consumption
o 80µA Supply Current at 1MHz Switching
Frequency
o No Phase Reversal for Overdriven Inputs
o Available in Space-Saving Packages:
UCSP (MAX985)
SOT23 (MAX985/MAX986/MAX989/MAX990)
µMAX® (MAX989/MAX990)
Ordering Information
PART
PIN-PACKAGE
TOP MARK
MAX985EBT+T
6 UCSP-6
AAY
MAX985EXK+T
5 SC70-5
ABK
Note: All devices are specified over the -40°C to +85°C operating
temperature range.
+Denotes a lead(Pb)-free/RoHS-compliant package.
T = Tape and reel.
Ordering Information continued at end of data sheet.
Typical Application Circuit appears at end of data sheet.
Pin Configurations
TOP VIEW
(BUMPS ON BOTTOM)
IN+
B1
A1
VEE
IN-
B2
A2
OUT
N.C.
B3
A3
VCC
MAX985
UCSP
Pin Configurations continued at end of data sheet.
For pricing, delivery, and ordering information, please contact Maxim Direct
at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX985/MAX986/MAX989/MAX990/MAX993/MAX994
General Description
MAX985/MAX986/MAX989/MAX990/MAX993/MAX994
Micropower, Low-Voltage, UCSP/SC70,
Rail-to-Rail I/O Comparators
ABSOLUTE MAXIMUM RATINGS
Supply Voltage (VCC to VEE) ...................................................6V
Current into Input Pins ......................................................±20mA
IN_-, IN_+ to VEE .......................................-0.3V to (VCC + 0.3V)
OUT_ to VEE
MAX985/MAX989/MAX993 ....................-0.3V to (VCC + 0.3V)
MAX986/MAX990/MAX994.....................................-0.3V to 6V
OUT_ Short-Circuit Duration to VEE or VCC ...........................10s
Continuous Power Dissipation (Multilayer board, TA = +70°C)
5-Pin SC70 (derate 3.1mW/°C above +70°C) ...............247mW
5-Pin SOT23 (derate 3.9mW/°C above +70°C)..........312.6mW
6-Bump UCSP (derate 3.9mW/°C above +70°C)..........308mW
8-Pin SOT23 (derate 5.1mW/°C above +70°C)..........408.2mW
8-Pin µMAX (derate 4.8mW/°C above +70°C) ...........387.8mW
8-Pin SO (derate 7.4mW/°C above +70°C)................588.2mW
14-Pin TSSOP (derate 10mW/°C above +70°C) ........796.8mW
14-Pin SO (derate 11.9mW/°C above +70°C)............952.4mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Soldering Temperature (reflow) ......................................+260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VCC = 2.7V to 5.5V, VEE = 0V, VCM = 0V, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
Supply Voltage
Supply Current per
Comparator
Power-Supply Rejection Ratio
Common-Mode Voltage
Range (Note 2)
Input Offset Voltage
(Note 3)
Input Hysteresis
SYMBOL
VCC
CONDITIONS
TA = -40°C to +85°C
UNITS
5.5
V
20
20
µA
24
55
TA = +25°C
Full common-mode
range
11
TA = -40°C to +85°C
2.5V ≤ VCC ≤ 5.5V
MAX
24
TA = +25°C
VCC = 2.7V
VOS
12
TA = -40°C to +85°C
ICC
VCMR
TYP
2.5
TA = +25°C
VCC = 5V
PSRR
MIN
Inferred from PSRR test
80
dB
VEE 0.25
VCC +
0.25
VEE
VCC
TA = +25°C
±0.5
TA = -40°C to +85°C
±5
±7
V
mV
VHYST
±3
IB
0.001
Input Offset Current
IOS
0.5
Input Capacitance
CIN
1.0
pF
80
dB
Input Bias Current
(Note 4)
Common-Mode Rejection Ratio
CMRR
Output Leakage Current
(MAX986/MAX990/
MAX994 only)
ILEAK
Output Short-Circuit Current
OUT Output Voltage Low
2
ISC
VOL
52
VOUT = high
mV
10
pA
1.0
Sourcing or sinking,
VOUT = VEE or VCC
VCC = 5V,
ISINK = 8mA
TA = +25°C
VCC = 2.7V,
ISINK = 3.5mA
TA = +25°C
VCC = 5V
95
VCC = 2.7V
35
0.2
TA = -40°C to +85°C
TA = -40°C to +85°C
µA
mA
0.4
0.55
0.15
nA
0.3
0.4
V
Micropower, Low-Voltage, UCSP/SC70,
Rail-to-Rail I/O Comparators
(VCC = 2.7V to 5.5V, VEE = 0V, VCM = 0V, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
OUT Output Voltage High
(MAX985/MAX989/
MAX993 only)
OUT Rise Time
(MAX985/MAX989/
MAX993 only)
OUT Fall Time
SYMBOL
VOH
tRISE
tFALL
tPDPropagation Delay
tPD+
Power-Up Time
tPU
CONDITIONS
MIN
TYP
VCC = 5V,
ISOURCE = 8mA
TA = +25°C
4.6
4.85
TA = -40°C to +85°C
4.45
VCC = 2.7V,
ISOURCE = 3.5mA
TA = +25°C
2.4
TA = -40°C to +85°C
2.3
CL = 15pF
40
CL = 50pF
50
CL = 200pF
80
CL = 15pF
40
CL = 50pF
50
CL = 200pF
80
MAX985/MAX989/ 10mV overdrive
MAX993 only
100mV overdrive
450
MAX986/MAX990/ 10mV overdrive
MAX994 only,
RPULLUP = 5.1kΩ 100mV overdrive
450
VCC = 5.0V
VCC = 5.0V
CL = 15pF
2.55
MAX985/MAX989/
MAX993 only, CL = 15pF
MAX
UNITS
V
ns
ns
300
ns
300
10mV overdrive
450
100mV overdrive
300
20
µs
Note 1: All device specifications are 100% production tested at TA = +25°C. Limits over the extended temperature range are guaranteed by design.
Note 2: Inferred from the VOS test. Both or either inputs can be driven 0.3V beyond either supply rail without output phase reversal.
Note 3: VOS is defined as the center of the hysteresis band at the input.
Note 4: IB is defined as the average of the two input bias currents (IB-, IB+).
3
MAX985/MAX986/MAX989/MAX990/MAX993/MAX994
ELECTRICAL CHARACTERISTICS (continued)
__________________________________________Typical Operating Characteristics
(VCC = 5V, VCM = 0V, TA = +25°C, unless otherwise noted.)
10,000
MAX985-02
VIN+ < VINOUTPUT LOW VOLTAGE (mV) (VOL)
VIN+ > VIN-
17
OUTPUT LOW VOLTAGE
vs. OUTPUT SINK CURRENT
1000
MAX985-01
18
SUPPLY CURRENT vs.
OUTPUT TRANSITION FREQUENCY
SUPPLY CURRENT (µA)
SUPPLY CURRENT (µA)
16
15
14
13
VCC = 5.0V
12
11
VCC = 2.7V
100
VCC = 5.0V
10
MAX985-04
SUPPLY CURRENT
vs. TEMPERATURE
VCC = 2.7V
10
1000
VCC = 2.7V
100
VCC = 5.0V
10
9
8
1
-40
-20
0
20
40
60
80
100
1
0.01
0.1
1
10
100
1000
0.01
0.1
1
10
TEMPERATURE (°C)
OUTPUT TRANSITION FREQUENCY (kHz)
OUTPUT SINK CURRENT (mA)
OUTPUT HIGH VOLTAGE
vs. OUTPUT SOURCE CURRENT
OUTPUT SHORT-CIRCUIT
CURRENT vs. TEMPERATURE
INPUT OFFSET VOLTAGE
vs. TEMPERATURE
OUTPUT SINK CURRENT (mA)
1000
VCC = 2.7V
VCC = 5.0V
1
VCC = 5.0V
70
60
50
1
10
MAX985-07
0.3
0.1
-0.3
100
-60
OUTPUT SOURCE CURRENT (mA)
-40
-20
0
20
40
60
80
-60
100
-40
-20
0
20
40
60
TEMPERATURE (°C)
TEMPERATURE (°C)
PROPAGATION DELAY
vs. CAPACITIVE LOAD (VCC = 5V)
PROPAGATION DELAY
vs. CAPACITIVE LOAD (VCC = 3V)
530
MAX985-05a
600
VOD = 50mV
VOD = 50mV
510
550
490
TO VOUT = 50% OF
FINAL VALUE
500
470
tPD (ns)
tPD (ns)
0.5
-0.1
0
0.1
0.01
0.7
VCC = 2.7V
20
10
0.1
0.9
80
40
30
TO VOUT = 50% OF
FINAL VALUE
450
430
450
TO VOUT = 10% OF
FINAL VALUE
400
410
TO VOUT = 10% OF
FINAL VALUE
390
370
350
350
0
200
400
600
CAPACITIVE LOAD (pF)
4
800
100
1.1
MAX985-05b
10
110
100
90
OFFSET VOLTAGE (mV)
VIN+ > VIN-
100
120
MAX985-08
10,000
MAX985-06
-60
OUTPUT HIGH VOLTAGE (VCC - VOH)
(mV)
MAX985/MAX986/MAX989/MAX990/MAX993/MAX994
Micropower, Low-Voltage, UCSP/SC70,
Rail-to-Rail I/O Comparators
1000
0
200
400
600
CAPACITIVE LOAD (pF)
800
1000
80
100
Micropower, Low-Voltage, UCSP/SC70,
Rail-to-Rail I/O Comparators
PROPAGATION DELAY
vs. INPUT OVERDRIVE
PROPAGATION DELAY
vs. TEMPERATURE
VOD = 50mV
440
MAX985-10
900
MAX985-09
450
800
700
600
TO VOUT = 50% POINT
OF FINAL VALUE
420
tPD (ns)
tPD (ns)
430
410
TO VOUT = 10% POINT
OF FINAL VALUE
400
500
VCC = 2.7V
400
300
VCC = 5.0V
200
390
100
0
380
-40
-20
0
20
40
60
80
0
100
40
MAX985/MAX989/MAX993
PROPAGATION DELAY (tPD+)
MAX985-12
50mV/
div
120
160
200
MAX985/MAX989/MAX993
SWITCHING CURRENT, OUT RISING
PROPAGATION DELAY (tPD-)
MAX985-11
IN+
80
INPUT OVERDRIVE (mV)
TEMPERATURE (°C)
MAX985-13
50mV/
div
IN+
IN+
50mV/
div
2V/div
OUT
2V/div
OUT
2V/div
OUT
1mA/div
ICC
VOD = 50mV
VOD = 50mV
VOD = 50mV
100ns/div
100ns/div
100ns/div
1MHz RESPONSE
SWITCHING CURRENT, OUT FALLING
POWER-UP DELAY
MAX985-15
MAX985-14
IN+
OUT
MAX985-16
IN+
50mV/
div
50mV/
div
VCC
2V/div
OUT
2V/div
ICC
OUT
VIN- = 50mV
VIN+ = 0V
1mA/div
VOD = 50mV
VOD = 50mV
100ns/div
200ns/div
5µs/div
5
MAX985/MAX986/MAX989/MAX990/MAX993/MAX994
____________________________Typical Operating Characteristics (continued)
(VCC = 5V, VCM = 0V, TA = +25°C, unless otherwise noted.)
MAX985/MAX986/MAX989/MAX990/MAX993/MAX994
Micropower, Low-Voltage, UCSP/SC70,
Rail-to-Rail I/O Comparators
Pin/Bump Description
BUMP
PIN
MAX985/
MAX986
MAX985
MAX993/
MAX994
NAME
FUNCTION
UCSP*
SO
SOT23/
SC70
SO/µMAX/
SOT23
SO/
TSSOP
A2
6
1
—
—
OUT
A3
7
2
8
4
VCC
Comparator Output
Positive Supply Voltage
B1
3
3
—
—
IN+
Comparator Noninverting Input
B2
2
4
—
—
IN-
Comparator Inverting Input
A1
4
5
4
11
VEE
Negative Supply Voltage
—
—
—
1
1
OUTA
—
—
—
2
2
INA-
Comparator A Inverting Input
—
—
—
3
3
INA+
Comparator A Noninverting Input
—
—
—
5
5
INB+
Comparator B Noninverting Input
—
—
—
6
6
INB-
Comparator B Inverting Input
—
—
—
7
7
OUTB
Comparator B Output
—
—
—
—
8
OUTC
Comparator C Output
—
—
—
—
B3
1, 5, 8
*MAX985 only
6
MAX989/
MAX990
—
—
Comparator A Output
9
INC-
Comparator C Inverting Input
10
INC+
Comparator C Noninverting Input
12
IND+
Comparator D Noninverting Input
13
IND-
Comparator D Inverting Input
14
OUTD
—
N.C.
Comparator D Output
No Connection. Not internally connected.
Micropower, Low-Voltage, UCSP/SC70,
Rail-to-Rail I/O Comparators
The MAX985/MAX986/MAX989/MAX990/MAX993/
MAX994 are single/dual/quad low-power, low-voltage
comparators. They have an operating supply voltage
range between 2.5V and 5.5V and consume only 11µA.
Their common-mode input voltage range extends 0.25V
beyond each rail. Internal hysteresis ensures clean output switching, even with slow-moving input signals.
Large internal output drivers allow rail-to-rail output
swing with up to 8mA loads.
The output stage employs a unique design that minimizes supply-current surges while switching, virtually
eliminating the supply glitches typical of many other
comparators. The MAX985/MAX989/MAX993 have a
push-pull output structure that sinks as well as sources
current. The MAX986/MAX990/MAX994 have an opendrain output stage that can be pulled beyond VCC to an
absolute maximum of 6V above VEE.
Input Stage Circuitry
The devices’ input common-mode range extends from
-0.25V to (VCC + 0.25V). These comparators may operate at any differential input voltage within these limits.
Input bias current is typically 1.0pA if the input voltage
is between the supply rails. Comparator inputs are protected from overvoltage by internal body diodes connected to the supply rails. As the input voltage exceeds
the supply rails, these body diodes become forward
biased and begin to conduct. Consequently, bias currents increase exponentially as the input voltage
exceeds the supply rails.
Output Stage Circuitry
These comparators contain a unique output stage
capable of rail-to-rail operation with up to 8mA loads.
Many comparators consume orders of magnitude more
current during switching than during steady-state operation. However, with this family of comparators, the
supply-current change during an output transition is
extremely small. The Typical Operating Characteristics
graph Supply Current vs. Output Transition Frequency
shows the minimal supply-current increase as the output switching frequency approaches 1MHz. This characteristic eliminates the need for power-supply filter
capacitors to reduce glitches created by comparator
switching currents. Another advantage realized in highspeed, battery-powered applications is a substantial
increase in battery life.
VCC
R3
R1
VIN
VCC
R2
OUT
VEE
VREF
MAX985
MAX989
MAX993
Figure 1. Additional Hysteresis (MAX985/MAX989/MAX993)
__________Applications Information
Additional Hysteresis
MAX985/MAX989/MAX993
The MAX985/MAX989/MAX993 have ±3mV internal
hysteresis. Additional hysteresis can be generated with
three resistors using positive feedback (Figure 1).
Unfortunately, this method also slows hysteresis
response time. Use the following procedure to calculate resistor values for the MAX985/MAX989/MAX993.
1) Select R3. Leakage current at IN is under 10nA, so
the current through R3 should be at least 1µA to
minimize errors caused by leakage current. The current through R3 at the trip point is (VREF - VOUT) /
R3. Considering the two possible output states in
solving for R3 yields two formulas: R3 = VREF / 1µA
or R3 = (VREF - VCC) / 1µA. Use the smaller of the
two resulting resistor values. For example, if VREF =
1.2V and VCC = 5V, then the two R3 resistor values
are 1.2MΩ and 3.8MΩ. Choose a 1.2MΩ standard
value for R3.
2) Choose the hysteresis band required (VHB). For this
example, choose 50mV.
3) Calculate R1 according to the following equation:
R1 = R3 x (VHB / VCC)
For this example, insert the values R1 = 1.2MΩ x
(50mV / 5V) = 12kΩ.
4) Choose the trip point for VIN rising (VTHR; VTHF is
the trip point for VIN falling). This is the threshold
voltage at which the comparator switches its output
from low to high as VIN rises above the trip point. For
this example, choose 3V.
7
MAX985/MAX986/MAX989/MAX990/MAX993/MAX994
_______________Detailed Description
MAX985/MAX986/MAX989/MAX990/MAX993/MAX994
Micropower, Low-Voltage, UCSP/SC70,
Rail-to-Rail I/O Comparators
5) Calculate R2 as follows. For this example, choose an
8.2kΩ standard value:
1
R2 =
⎛ VTHR ⎞
1
1
⎜V
⎟ − R1 − R 3
⎝ REF x R1⎠
R2 =
1
⎛
1
1
3.0V ⎞
−
⎜
⎟ −
12kΩ
2.2MΩ
⎝ 1.2 x 12kΩ ⎠
= 8.03kΩ
6) Verify trip voltages and hysteresis as follows:
⎛ 1
1
1⎞
+
+
VIN rising: VTHR = VREF x R1 x ⎜
⎟
R2
R3 ⎠
⎝ R1
⎛ R1 x VCC ⎞
VIN falling : VTHF = VTHR − ⎜
⎟
R3
⎝
⎠
Use the following procedure to calculate resistor
values:
1) Select R3 according to the formulas R3 = VREF /
500µA or R3 = (VREF - VCC) / 500µA - R4. Use the
smaller of the two resulting resistor values.
2) Choose the hysteresis band required (VHB). For this
example, choose 50mV.
3) Calculate R1 according to the following equation:
R1 = (R3 + R4) x (VHB / VCC)
4) Choose the trip point for VIN rising (VTHR; VTHF is
the trip point for VIN falling). This is the threshold
voltage at which the comparator switches its output
from low to high as VIN rises above the trip point.
5) Calculate R2 as follows:
R2 =
Hysteresis = VTHR − VTHF
MAX986/MAX990/MAX994
The MAX986/MAX990/MAX994 have ±3mV internal
hysteresis. They have open-drain outputs and require
an external pullup resistor (Figure 2). Additional hysteresis can be generated using positive feedback, but
the formulas differ slightly from those of the
MAX985/MAX989/MAX993.
1
⎛ VTHR ⎞
1
1
⎜V
⎟ − R1 − R 3 + R4
x
R
1
⎝ REF
⎠
6) Verify trip voltages and hysteresis as follows:
VIN rising: VTHR = VREF x R1 x
⎛ 1
⎞
1
1
+
+
⎜
⎟
R2
R3 + R4 ⎠
⎝ R1
⎛ R1 x VCC ⎞
VIN falling : VTHF = VTHR − ⎜
⎟
⎝ R3 + R4 ⎠
Hysteresis = VTHR − VTHF
VCC
R3
Board Layout and Bypassing
R1
R4
VIN
VCC
R2
OUT
VEE
VREF
MAX986
MAX990
MAX994
Figure 2. Additional Hysteresis (MAX986/MAX990/MAX994)
8
Power-supply bypass capacitors are not typically needed, but use 100nF bypass capacitors when supply
impedance is high, when supply leads are long,
or when excessive noise is expected on the supply
lines. Minimize signal trace lengths to reduce stray
capacitance.
Micropower, Low-Voltage, UCSP/SC70,
Rail-to-Rail I/O Comparators
Logic-Level Translator
Figure 4 shows an application that converts 5V logic levels to 3V logic levels. The MAX986 is powered by the 5V
supply voltage, and the pullup resistor for the MAX986’s
open-drain output is connected to the 3V supply voltage.
This configuration allows the full 5V logic swing without
creating overvoltage on the 3V logic inputs. For 3V to 5V
logic-level translation, simply connect the 3V supply to
VCC and the 5V supply to the pullup resistor.
UCSP Applications Information
For the latest application details on UCSP construction,
dimensions, tape carrier information, PCB techniques,
bump-pad layout, and recommended reflow temperature profile, as well as the latest information on reliability
testing results, refer to the Application Note: UCSP—A
Wafer-Level Chip-Scale Package on Maxim’s web site
at www.maxim-ic.com/ucsp.
5V (3V)
VCC
3V (5V)
2
2
100kΩ
VCC
VCC
100mV
4
3 IN+
OUT 1
OUT
100kΩ
3
4 IN-
RPULLUP
IN1
3V (5V)
LOGIC OUT
IN+
MAX986
MAX985
VEE
VEE
5
Figure 3. Zero-Crossing Detector
5
5V (3V) LOGIC IN
Figure 4. Logic-Level Translator
9
MAX985/MAX986/MAX989/MAX990/MAX993/MAX994
Zero-Crossing Detector
Figure 3 shows a zero-crossing detector application.
The MAX985’s inverting input is connected to ground,
and its noninverting input is connected to a 100mVP-P
signal source. As the signal at the noninverting input
crosses 0V, the comparator’s output changes state.
Micropower, Low-Voltage, UCSP/SC70,
Rail-to-Rail I/O Comparators
MAX985/MAX986/MAX989/MAX990/MAX993/MAX994
Typical Application Circuit
Ordering Information (continued)
PART
VCC
VIN
VCC
*RPULLUP
IN+
OUT
IN-
MAX98_
MAX99_
VEE
VREF
*MAX986/MAX990/MAX994 ONLY.
THRESHOLD DETECTOR
PIN-PACKAGE
TOP MARK
ABYZ
MAX985EUK+T
5 SOT23-5
MAX985ESA+
8 SO
MAX986EXK+T
5 SC70-5
MAX986EUK+T
5 SOT23-5
MAX986ESA+
8 SO
MAX989EKA+T
8 SOT23-8
AADZ
MAX989EUA+T
8 µMAX-8
—
MAX989ESA+
8 SO
MAX990EKA+T
8 SOT23-8
AAEA
MAX990EUA+T
8 µMAX-8
—
MAX990ESA+
8 SO
—
MAX993EUD+
14 TSSOP
—
MAX993ESD+
14 SO
—
MAX994EUD+
14 TSSOP
—
MAX994ESD+
14 SO
—
—
ABL
ABZA
—
—
Note: All devices are specified over the -40°C to +85°C operating
temperature range.
+Denotes a lead(Pb)-free/RoHS-compliant package.
T = Tape and reel.
Pin Configurations (continued)
TOP VIEW
VCC 2
5
VEE
IN+ 3
IN+ 3
4
SOT23/SC70
N.C. 1
8
IN- 2
MAX985
MAX986
IN-
+
+
+
+
OUT 1
MAX985
MAX986
VEE 4
SO
N.C.
OUTA 1
7
VCC
INA- 2
6
OUT
INA+ 3
5
N.C.
VEE 4
8
MAX989
MAX990
VCC
7
OUTB
6
INB-
5
INB+
OUTA 1
14 OUTD
INA- 2
13 IND12 IND+
INA+ 3
SO/µMAX/SOT23
VCC 4
INB+ 5
MAX993
MAX994
10 INC+
INB- 6
9
INC-
OUTB 7
8
OUTC
SO/TSSOP
10
11 VEE
Micropower, Low-Voltage, UCSP/SC70,
Rail-to-Rail I/O Comparators
For the latest package outline information and land patterns (footprints), go to www.maxim-ic.com/packages. Note that a “+”, “#”, or
“-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status.
PACKAGE TYPE
PACKAGE CODE
OUTLINE NO.
LAND
PATTERN NO.
6 UCSP
B6+3
21-0097
—
5 SOT23
U5+1
21-0057
90-0174
5 SC70
X5+1
21-0076
90-0188
8 SO
S8+2
21-0041
90-0096
8 SOT23
K8+5
21-0078
90-0176
8 µMAX
U8+1
21-0036
90-0092
14 SO
S14+1
21-0041
90-0112
14 TSSOP
U14+1
21-0066
90-0113
11
MAX985/MAX986/MAX989/MAX990/MAX993/MAX994
Package Information
MAX985/MAX986/MAX989/MAX990/MAX993/MAX994
Micropower, Low-Voltage, UCSP/SC70,
Rail-to-Rail I/O Comparators
Revision History
REVISION
NUMBER
REVISION
DATE
5
4/12
DESCRIPTION
Replaced Figure 3, added lead-free compliant packaging info, updated package
information, updated Absolute Maximum Ratings, rearranged Pin Description table
PAGES
CHANGED
1, 2, 6, 9, 10
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in
the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
12
_______________Maxim Integrated Products, Inc. 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000
© 2012 Maxim Integrated Products
Maxim is a registered trademark of Maxim Integrated Products, Inc.
Similar pages