Fujitsu MB84VD21194 16m ( x 8/ x 16) flash memory & 4m ( x 8/ x 16) static ram Datasheet

FUJITSU SEMICONDUCTOR
DATA SHEET
DS05-50202-2E
Stacked MCP (Multi-Chip Package) FLASH MEMORY & SRAM
CMOS
16M ( × 8/ × 16) FLASH MEMORY &
4M ( × 8/ × 16) STATIC RAM
MB84VD2118XA-85/MB84VD2119XA-85
■ FEATURES
• Power supply voltage of 2.7 to 3.6 V
• High performance
85 ns maximum access time
• Operating Temperature
−25 to +85 °C
• Package 69-ball FBGA, 56-pin TSOP(I)
(Continued)
■ PRODUCT LINE UP
Flash Memory
Ordering Part No.
VCCf, VCCs = 3.0 V
+0.6 V
−0.3 V
SRAM
MB84VD2118XA-85/MB84VD2119XA-85
Max. Address Access Time (ns)
85
85
Max. CE Access Time (ns)
85
85
Max. OE Access Time (ns)
35
45
■ PACKAGES
69-ball plastic FBGA
56-pin plastic TSOP(I)
(BGA-69P-M02)
(FPT-56P-M04)
MB84VD2118XA-85/MB84VD2119XA-85
(Continued)
1. FLASH MEMORY
• Simultaneous Read/Write operations (dual bank)
Miltiple devices available with different bank sizes (Refer to “PIN DESCRIPTION”)
Host system can program or erase in one bank, then immediately and simultaneously read from the other bank
Zero latency between read and write operations
Read-while-erase
Read-while-program
• Minimum 100,000 write/erase cycles
• Sector erase architecture
Eight 4 K words and thirty one 32 K words.
Any combination of sectors can be concurrently erased. Also supports full chip erase.
• Boot Code Sector Architecture
MB84VD2118XA : Top sector
MB84VD2119XA : Bottom sector
• Embedded EraseTM* Algorithms
Automatically pre-programs and erases the chip or any sector
• Embedded ProgramTM* Algorithms
Automatically writes and verifies data at specified address
• Data Polling and Toggle Bit feature for detection of program or erase cycle completion
• Ready-Busy output (RY/BY)
Hardware method for detection of program or erase cycle completion
• Automatic sleep mode
When addresses remain stable, automatically switch themselves to low power mode.
• Low VCCf write inhibit ≤ 2.5 V
• Hidden ROM (Hi-ROM) region
64K byte of Hi-ROM, accessible through a new “Hi-ROM Enable” command sequence
Factory serialized and protected to provide a secure electronic serial number (ESN)
• WP/ACC input pin
At VIL, allows protection of boot sectors, regardless of sector protection/unprotection status
(MB84VD2118XA : SA37, SA38 MB84VD2119XA : SA0, SA1)
At VIH, allows removal of boot sector protection
At VACC, program time will reduse by 40%.
• Erase Suspend/Resume
Suspends the erase operation to allow a read in another sector within the same device
• Please refer to “MBM29DL16XTD/BD” data sheet in detailed function
2. SRAM
• Power dissipation
Operating : 40 mA max.
Standby : 7 µA max.
• Power down features using CE1s and CE2s
• Data retention supply voltage : 1.5 V to 3.6 V
• CE1s and CE2s Chip Select
• Byte data control : LBs (DQ0 to DQ7) , UBs (DQ8 to DQ15)
* : Embedded EraseTM and Embedded ProgramTM are trademarks of Advanced Micro Devices, Inc.
2
MB84VD2118XA-85/MB84VD2119XA-85
■ PIN ASSIGNMENTS
(Top View)
A
N.C.
B
N.C.
N.C.
N.C.
N.C.
A7
LBS
WP/
ACC
WE
A8
A11
C
A3
A6
UBS
RESET
CE2S
A19
A12
A15
D
A2
A5
A18
RY/BY
N.C.
A9
A13
N.C.
E
N.C.
A1
A4
A17
A10
A14
N.C.
N.C.
F
N.C.
A0
VSS
DQ1
DQ6
SA
A16
N.C.
G
CEf
OE
DQ9
DQ3
DQ4
DQ13
DQ15/
A−1
CIOf
H
CE1S
DQ0
DQ10
VCCf
VCCs
DQ12
DQ7
VSS
DQ8
DQ2
DQ11
CIOS
DQ5
DQ14
N.C.
N.C.
5
6
J
K
N.C.
1
2
3
4
N.C.
7
8
9
10
69-ball FBGA
3
MB84VD2118XA-85/MB84VD2119XA-85
(Top View)
N.C.
1
56
A16
A15
2
55
CIOf
A14
3
54
VSS
A13
4
53
SA
A12
5
52
DQ15/A-1
A11
6
51
DQ7
A10
7
50
DQ14
A9
8
49
DQ6
A8
9
48
DQ13
A19
10
47
DQ5
N.C.
11
46
DQ12
WE
12
45
DQ4
CE2s
13
44
CIOs
RESET
14
43
VCCs
WP/ACC
15
42
VCCf
RY/BY
16
41
DQ11
UBs
17
40
DQ3
LBs
18
39
DQ10
A18
19
38
DQ2
A17
20
37
DQ9
A7
21
36
DQ1
A6
22
35
DQ8
A5
23
34
DQ0
A4
24
33
OE
A3
25
32
VSS
A2
26
31
CE1s
A1
27
30
CEf
N.C.
28
29
A0
56-pin TSOP(I)
4
MB84VD2118XA-85/MB84VD2119XA-85
■ PIN DESCRIPTION
Pin
A0 to A17
Function
Input/Output
Address Inputs (Common)
I
A-1, A18, A19
Address Input (Flash)
I
SA
Address Input (SRAM)
I
DQ0 to DQ15
Data Inputs/Outputs (Common)
I/O
CEf
Chip Enable (Flash)
I
CE1s
Chip Enable (SRAM)
I
CE2s
Chip Enable (SRAM)
I
OE
Output Enable (Common)
I
WE
Write Enable (Common)
I
Ready/Busy Outputs (Flash) Open Drain Output
O
UBs
Upper Byte Control (SRAM)
I
LBs
Lower Byte Control (SRAM)
I
CIOf
I/O Configuration (Flash)
CIOf = VIH is Word mode ( × 16), CIOf = VIL is Byte mode ( × 8)
I
CIOs
I/O Configuration (SRAM)
CIOs = VIH is Word mode ( × 16), CIOs = VIL is Byte mode ( × 8)
I
Hardware Reset Pin/Sector Protection Unlock (Flash)
I
Write Protect / Acceleration (Flash)
I
RY/BY
RESET
WP/ACC

N.C.
No Internal Connection
VSS
Device Ground (Common)
Power
VCCf
Device Power Supply (Flash)
Power
VCCs
Device Power Supply (SRAM)
Power
5
MB84VD2118XA-85/MB84VD2119XA-85
■ BLOCK DIAGRAM
VCCf
VSS
A0 to A19
RY/BY
A0 to A19
A-1
WP/ACC
RESET
CEf
CIOf
16 M bit
Flash Memory
DQ0 to DQ15/A-1
DQ0 to DQ15/A-1
VCCs
VSS
A0 to A17
DQ0 to DQ15/A-1
SA
LBs
UBs
WE
OE
CE1s
CE2s
CIOs
6
4 M bit
Static RAM
MB84VD2118XA-85/MB84VD2119XA-85
■ DEVICE BUS OPERATIONS
Table 2.1 User Bus Operations (Flash = Word mode; CIOf = VCCf, SRAM = Word mode; CIOs = VCCs)
Operation
(Note 1, 3)
Full Standby
CEf CE1s CE2s OE
H
H
Output Disable
L
Read from Flash
(Note 2)
L
Write to Flash
L
Read from SRAM
Write to SRAM
H
H
Temporary Sector
Group
Unprotection
(Note 4)
X
Flash Hardware
Reset
X
Boot Block Sector
Write Protection
X
H
X
X
L
L
H
H
X
X
L
H
X
X
L
H
X
X
L
L
L
H
H
X
X
H
X
X
L
X
X
WE
SA
LBs UBs
(Note 6)
DQ0 to
DQ7
DQ8 to
DQ15
RESET
WP/
ACC
(Note 5)
H
X
H
X
X
X
X
X
X
HIGH-Z
HIGH-Z
H
H
X
X
X
HIGH-Z
HIGH-Z
X
X
X
H
H
HIGH-Z
HIGH-Z
H
H
X
X
X
HIGH-Z
HIGH-Z
L
H
X
X
X
DOUT
DOUT
H
X
H
L
X
X
X
DIN
DIN
H
X
L
L
DOUT
DOUT
H
L
HIGH-Z
DOUT
H
X
L
H
DOUT
HIGH-Z
L
L
DIN
DIN
H
L
HIGH-Z
DIN
H
X
L
H
DIN
HIGH-Z
L
X
H
L
X
X
X
X
X
X
X
X
X
VID
X
X
X
X
X
X
HIGH-Z
HIGH-Z
L
X
X
X
X
X
X
X
X
X
L
Legend: L = VIL, H = VIH, X = VIL or VIH. See “ELECTRICAL CHARACTERISTICS 1. DC Characteristics” for
voltage levels.
Notes : 1. Other operations except for indicated this column are inhibited.
2. WE can be VIL if OE is VIL, OE at VIH initiates the write operations.
3. Do not apply CEf = VIL, CE1s = VIL and CE2s = VIH at a time.
4. It is also used for the extended sector group protections.
5. WP/ACC = VIL ; protection of boot sectors.
WP/ACC = VIH ; removal of boot sectors protection.
WP/ACC = VACC (9V) ; Program time will reduce by 40%.
6. SA ; Don’t care or Open.
7
MB84VD2118XA-85/MB84VD2119XA-85
Table 2.2 User Bus Operations (Flash = Word mode; CIOf = VCCf, SRAM = Byte mode; CIOs = VSS)
Operation
(Note 1, 3)
Full Standby
CEf CE1s CE2s OE
H
H
Output Disable
L
H
X
X
L
L
H
H
X
X
L
H
X
X
L
H
X
X
L
WE SA
LBs
UBs
(Note 6) (Note 6)
DQ0 to
DQ7
DQ8 to
RESET
DQ15
X
X
X
X
X
HIGH-Z HIGH-Z
H
H
X
X
X
HIGH-Z HIGH-Z
X
X
X
X
X
HIGH-Z HIGH-Z
H
H
X
X
X
HIGH-Z HIGH-Z
L
H
X
X
X
DOUT
H
L
X
X
X
WP/
ACC
(Note 5)
H
X
H
X
DOUT
H
X
DIN
DIN
H
X
Read from Flash
(Note 2)
L
Write to Flash
L
Read from SRAM
H
L
H
L
H
SA
X
X
DOUT
HIGH-Z
H
X
Write to SRAM
H
L
H
X
L
SA
X
X
DIN
HIGH-Z
H
X
Temporary Sector
Group
Unprotection
(Note 4)
X
X
X
X
X
X
X
X
X
X
VID
X
Flash Hardware
Reset
X
H
X
X
L
X
X
X
X
X
L
X
Boot Block Sector
Write Protection
X
X
X
X
X
X
X
X
X
L
HIGH-Z HIGH-Z
X
X
Legend: L = VIL, H = VIH, X = VIL or VIH. See “ELECTRICAL CHARACTERISTICS 1. DC Characteristics” for
voltage levels.
Notes : 1. Other operations except for indicated this column are inhibited.
2. WE can be VIL if OE is VIL, OE at VIH initiates the write operations.
3. Do not apply CEf = VIL, CE1s = VIL and CE2s = VIH at a time.
4. It is also used for the extended sector group protections.
5. WP/ACC = VIL ; protection of boot sectors.
WP/ACC = VIH ; removal of boot sectors protection.
WP/ACC = VACC (9V) ; Program time will reduce by 40%.
6. LBS , UBS ; Don’t care or Open.
8
MB84VD2118XA-85/MB84VD2119XA-85
Table 2.3 User Bus Operations (Flash = Byte mode; CIOf = VSS, SRAM = Byte mode; CIOs = VSS)
Operation
(Note 1, 3)
Full Standby
CEf CE1s CE2s
H
H
Output
Disable
L
H
X
X
L
L
H
H
X
X
L
H
X
X
L
H
X
X
L
DQ1/
LBs
UBs
DQ0 to
OE WE SA
A-1
(Note 6) (Note 6)
DQ7
DQ8 to
RESET
DQ14
X
X
X
X
X
X
HIGH-Z HIGH-Z
X
H
H
X
X
X
HIGH-Z HIGH-Z
X
X
X
X
X
X
HIGH-Z HIGH-Z
A-1
H
H
X
X
X
HIGH-Z HIGH-Z
A-1
L
H
X
X
X
DOUT
A-1
H
L
X
X
X
WP/
ACC
(Note 5)
H
X
H
X
X
H
X
DIN
X
H
X
Read from
Flash
(Note 2)
L
Write to
Flash
L
Read from
SRAM
H
L
H
X
L
H
SA
X
X
DOUT
HIGH-Z
H
X
Write to
SRAM
H
L
H
X
X
L
SA
X
X
DIN
HIGH-Z
H
X
Temporary
Sector Group
Unprotection
(Note 4)
X
X
X
X
X
X
X
X
X
X
X
VID
X
Flash
Hardware
Reset
H
X
X
X
L
X
X
X
X
X
X
L
X
Boot Block
Sector Write
Protection
X
X
X
X
X
X
X
X
X
X
L
HIGH-Z HIGH-Z
X
X
Legend: L = VIL, H = VIH, X = VIL or VIH. See “ELECTRICAL CHARACTERISTICS 1. DC Characteristics” for
voltage levels.
Notes : 1. Other operations except for indicated this column are inhibited.
2. WE can be VIL if OE is VIL, OE at VIH initiates the write operations.
3. Do not apply CEf = VIL, CE1s = VIL and CE2s = VIH at a time.
4. It is also used for the extended sector group protections.
5. WP/ACC = VIL ; protection of boot sectors.
WP/ACC = VIH ; removal of boot sectors protection.
WP/ACC = VACC (9V) ; Program time will reduce by 40%.
6. LBS, UBS ; Don’t care or Open.
9
MB84VD2118XA-85/MB84VD2119XA-85
■ FLEXIBLE SECTOR-ERASE ARCHITECTURE on FLASH MEMORY
• Eight 4 K words, and thirty one 32 K words.
• Individual-sector, multiple-sector, or bulk-erase capability.
Word mode Byte mode
SA38 :
SA37 :
SA36 :
Bank 1 SA35 :
MB84VD21181A
SA34 :
SA33 :
Bank 1
SA32 :
MB84VD21182A
SA31 :
SA30 :
Bank 1
SA29 :
MB84VD21183A
SA28 :
SA27 :
Bank 1
SA26 :
MB84VD21184A
SA25 :
SA24 :
SA23 :
SA22 :
SA21 :
SA20 :
SA19 :
SA18 :
SA17 :
SA16 :
SA15 :
Bank 2 SA14 :
MB84VD21181A
SA13 :
SA12 :
Bank 2
SA11 :
MB84VD21182A
SA10 :
SA9 :
Bank 2
SA8 :
MB84VD21183A
SA7 :
Bank 2
SA6 :
MB84VD21184A
SA5 :
SA4 :
SA3 :
SA2 :
SA1 :
SA0 :
8KB
8KB
8KB
8KB
8KB
8KB
8KB
8KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
(4KW)
(4KW)
(4KW)
(4KW)
(4KW)
(4KW)
(4KW)
(4KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
MB84VD2118XA Sector Architecture (Top Boot Block)
10
0FFFFFH
0FF000H
0FE000H
0FD000H
0FC000H
0FB000H
0FA000H
0F9000H
0F8000H
0F0000H
0E8000H
0E0000H
0D8000H
0D0000H
0C8000H
0C0000H
0B8000H
0B0000H
0A8000H
0A0000H
098000H
090000H
088000H
080000H
078000H
070000H
068000H
060000H
058000H
050000H
048000H
040000H
038000H
030000H
028000H
020000H
018000H
010000H
008000H
000000H
1FFFFFH
1FE000H
1FC000H
1FA000H
1F8000H
1F6000H
1F4000H
1F2000H
1F0000H
1E0000H
1D0000H
1C0000H
1B0000H
1A0000H
190000H
180000H
170000H
160000H
150000H
140000H
130000H
120000H
110000H
100000H
0F0000H
0E0000H
0D0000H
0C0000H
0B0000H
0A0000H
090000H
080000H
070000H
060000H
050000H
040000H
030000H
020000H
010000H
000000H
MB84VD2118XA-85/MB84VD2119XA-85
• Eight 4 K words, and thirty one 32 K words.
• Individual-sector, multiple-sector, or bulk-erase capability.
Word mode Byte mode
SA38 :
SA37 :
SA36 :
Bank 2
SA35 :
MB84VD21194A
SA34 :
SA33 :
Bank 2
SA32 :
MB84VD21193A
SA31 :
SA30 :
Bank 2
SA29 :
MB84VD21192A
SA28 :
SA27 :
Bank 2 SA26 :
MB84VD21191A SA25 :
SA24 :
SA23 :
SA22 :
SA21 :
SA20 :
SA19 :
SA18 :
SA17 :
SA16 :
SA15 :
SA14 :
SA13 :
SA12 :
Bank 1
SA11 :
MB84VD21194A
SA10 :
SA9 :
Bank 1
SA8 :
MB84VD21193A
SA7 :
SA6 :
Bank 1
SA5 :
MB84VD21192A
SA4 :
Bank 1 SA3 :
MB84VD21191A SA2 :
SA1 :
SA0 :
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
64KB
8KB
8KB
8KB
8KB
8KB
8KB
8KB
8KB
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(32KW)
(4KW)
(4KW)
(4KW)
(4KW)
(4KW)
(4KW)
(4KW)
(4KW)
0FFFFFH
0F8000H
0F0000H
0E8000H
0E0000H
0D8000H
0D0000H
0C8000H
0C0000H
0B8000H
0B0000H
0A8000H
0A0000H
098000H
090000H
088000H
080000H
078000H
070000H
068000H
060000H
058000H
050000H
048000H
040000H
038000H
030000H
028000H
020000H
018000H
010000H
008000H
007000H
006000H
005000H
004000H
003000H
002000H
001000H
000000H
1FFFFFH
1F0000H
1E0000H
1D0000H
1C0000H
1B0000H
1A0000H
190000H
180000H
170000H
160000H
150000H
140000H
130000H
120000H
110000H
100000H
0F0000H
0E0000H
0D0000H
0C0000H
0B0000H
0A0000H
090000H
080000H
070000H
060000H
050000H
040000H
030000H
020000H
010000H
00E000H
00C000H
00A000H
008000H
006000H
004000H
002000H
000000H
MB84VD2119XA Sector Architecture (Bottom Boot Block)
11
MB84VD2118XA-85/MB84VD2119XA-85
Table 3.1 Sector Address Tables (MB84VD21181)
Sector Address
Bank
Bank 2
Bank 1
12
Sector
Bank Address
Address Range
(Byte mode)
Address Range
(Word mode)
A19
A18
A17
A16
A15
A14
A13
A12
SA0
0
0
0
0
0
X
X
X
000000H to 00FFFFH
000000H to 007FFFH
SA1
0
0
0
0
1
X
X
X
010000H to 01FFFFH
008000H to 00FFFFH
SA2
0
0
0
1
0
X
X
X
020000H to 02FFFFH
010000H to 017FFFH
SA3
0
0
0
1
1
X
X
X
030000H to 03FFFFH
018000H to 01FFFFH
SA4
0
0
1
0
0
X
X
X
040000H to 04FFFFH
020000H to 027FFFH
SA5
0
0
1
0
1
X
X
X
050000H to 05FFFFH
028000H to 02FFFFH
SA6
0
0
1
1
0
X
X
X
060000H to 06FFFFH
030000H to 037FFFH
SA7
0
0
1
1
1
X
X
X
070000H to 07FFFFH
038000H to 03FFFFH
SA8
0
1
0
0
0
X
X
X
080000H to 08FFFFH
040000H to 047FFFH
SA9
0
1
0
0
1
X
X
X
090000H to 09FFFFH
048000H to 04FFFFH
SA10
0
1
0
1
0
X
X
X
0A0000H to 0AFFFFH
050000H to 057FFFH
SA11
0
1
0
1
1
X
X
X
0B0000H to 0BFFFFH
058000H to 05FFFFH
SA12
0
1
1
0
0
X
X
X
0C0000H to 0CFFFFH
060000H to 067FFFH
SA13
0
1
1
0
1
X
X
X
0D0000H to 0DFFFFH
068000H to 06FFFFH
SA14
0
1
1
1
0
X
X
X
0E0000H to 0EFFFFH
070000H to 077FFFH
SA15
0
1
1
1
1
X
X
X
0F0000H to 0FFFFFH
078000H to 07FFFFH
SA16
1
0
0
0
0
X
X
X
100000H to 10FFFFH
080000H to 087FFFH
SA17
1
0
0
0
1
X
X
X
110000H to 11FFFFH
088000H to 08FFFFH
SA18
1
0
0
1
0
X
X
X
120000H to 12FFFFH
090000H to 097FFFH
SA19
1
0
0
1
1
X
X
X
130000H to 13FFFFH
098000H to 09FFFFH
SA20
1
0
1
0
0
X
X
X
140000H to 14FFFFH
0A0000H to 0A7FFFH
SA21
1
0
1
0
1
X
X
X
150000H to 15FFFFH
0A8000H to 0AFFFFH
SA22
1
0
1
1
0
X
X
X
160000H to 16FFFFH
0B0000H to 0B7FFFH
SA23
1
0
1
1
1
X
X
X
170000H to 17FFFFH
0B8000H to 0BFFFFH
SA24
1
1
0
0
0
X
X
X
180000H to 18FFFFH
0C0000H to 0C7FFFH
SA25
1
1
0
0
1
X
X
X
190000H to 19FFFFH
0C8000H to 0CFFFFH
SA26
1
1
0
1
0
X
X
X
1A0000H to 1AFFFFH
0D0000H to 0D7FFFH
SA27
1
1
0
1
1
X
X
X
1B0000H to 1BFFFFH
0D8000H to 0DFFFFH
SA28
1
1
1
0
0
X
X
X
1C0000H to 1CFFFFH
0E0000H to 0E7FFFH
SA29
1
1
1
0
1
X
X
X
1D0000H to 1DFFFFH
0E8000H to 0EFFFFH
SA30
1
1
1
1
0
X
X
X
1E0000H to 1EFFFFH
0F0000H to 0F7FFFH
SA31
1
1
1
1
1
0
0
0
1F0000H to 1F1FFFH
0F8000H to 0F8FFFH
SA32
1
1
1
1
1
0
0
1
1F2000H to 1F3FFFH
0F9000H to 0F9FFFH
SA33
1
1
1
1
1
0
1
0
1F4000H to 1F5FFFH
0FA000H to 0FAFFFH
SA34
1
1
1
1
1
0
1
1
1F6000H to 1F7FFFH
0FB000H to 0FBFFFH
SA35
1
1
1
1
1
1
0
0
1F8000H to 1F9FFFH
0FC000H to 0FCFFFH
SA36
1
1
1
1
1
1
0
1
1FA000H to 1FBFFFH
0FD000H to 0FDFFFH
SA37
1
1
1
1
1
1
1
0
1FC000H to 1FDFFFH
0FE000H to 0FEFFFH
SA38
1
1
1
1
1
1
1
1
1FE000H to 1FFFFFH
0FF000H to 0FFFFFH
MB84VD2118XA-85/MB84VD2119XA-85
Table 3.2 Sector Address Tables (MB84VD21191)
Sector Address
Bank
Bank 1
Bank 2
Sector
Bank Address
Address Range
(BYTE mode)
Address Range
(WORD mode)
A19
A18
A17
A16
A15
A14
A13
A12
SA0
0
0
0
0
0
0
0
0
000000H to 001FFFH
000000H to 000FFFH
SA1
0
0
0
0
0
0
0
1
002000H to 003FFFH
001000H to 001FFFH
SA2
0
0
0
0
0
0
1
0
004000H to 005FFFH
002000H to 002FFFH
SA3
0
0
0
0
0
0
1
1
006000H to 007FFFH
003000H to 003FFFH
SA4
0
0
0
0
0
1
0
0
008000H to 009FFFH
004000H to 004FFFH
SA5
0
0
0
0
0
1
0
1
00A000H to 00BFFFH
005000H to 005FFFH
SA6
0
0
0
0
0
1
1
0
00C000H to 00DFFFH
006000H to 006FFFH
SA7
0
0
0
0
0
1
1
1
00E000H to 00FFFFH
007000H to 007FFFH
SA8
0
0
0
0
1
X
X
X
010000H to 01FFFFH
008000H to 00FFFFH
SA9
0
0
0
1
0
X
X
X
020000H to 02FFFFH
010000H to 017FFFH
SA10
0
0
0
1
1
X
X
X
030000H to 03FFFFH
018000H to 01FFFFH
SA11
0
0
1
0
0
X
X
X
040000H to 04FFFFH
020000H to 027FFFH
SA12
0
0
1
0
1
X
X
X
050000H to 05FFFFH
028000H to 02FFFFH
SA13
0
0
1
1
0
X
X
X
060000H to 06FFFFH
030000H to 037FFFH
SA14
0
0
1
1
1
X
X
X
070000H to 07FFFFH
038000H to 03FFFFH
SA15
0
1
0
0
0
X
X
X
080000H to 08FFFFH
040000H to 047FFFH
SA16
0
1
0
0
1
X
X
X
090000H to 09FFFFH
048000H to 04FFFFH
SA17
0
1
0
1
0
X
X
X
0A0000H to 0AFFFFH
050000H to 057FFFH
SA18
0
1
0
1
1
X
X
X
0B0000H to 0BFFFFH
058000H to 05FFFFH
SA19
0
1
1
0
0
X
X
X
0C0000H to 0CFFFFH
060000H to 067FFFH
SA20
0
1
1
0
1
X
X
X
0D0000H to 0DFFFFH
068000H to 06FFFFH
SA21
0
1
1
1
0
X
X
X
0E0000H to 0EFFFFH
070000H to 077FFFH
SA22
0
1
1
1
1
X
X
X
0F0000H to 0FFFFFH
078000H to 07FFFFH
SA23
1
0
0
0
0
X
X
X
100000H to 10FFFFH
080000H to 087FFFH
SA24
1
0
0
0
1
X
X
X
110000H to 11FFFFH
088000H to 08FFFFH
SA25
1
0
0
1
0
X
X
X
120000H to 12FFFFH
090000H to 097FFFH
SA26
1
0
0
1
1
X
X
X
130000H to 13FFFFH
098000H to 09FFFFH
SA27
1
0
1
0
0
X
X
X
140000H to 14FFFFH
0A0000H to 0A7FFFH
SA28
1
0
1
0
1
X
X
X
150000H to 15FFFFH
0A8000H to 0AFFFFH
SA29
1
0
1
1
0
X
X
X
160000H to 16FFFFH
0B0000H to 0B7FFFH
SA30
1
0
1
1
1
X
X
X
170000H to 17FFFFH
0B8000H to 0BFFFFH
SA31
1
1
0
0
0
X
X
X
180000H to 18FFFFH
0C0000H to 0C7FFFH
SA32
1
1
0
0
1
X
X
X
190000H to 19FFFFH
0C8000H to 0CFFFFH
SA33
1
1
0
1
0
X
X
X
1A0000H to 1AFFFFH
0D0000H to 0D7FFFH
SA34
1
1
0
1
1
X
X
X
1B0000H to 1BFFFFH
0D8000H to 0DFFFFH
SA35
1
1
1
0
0
X
X
X
1C0000H to 1CFFFFH
0E0000H to 0E7FFFH
SA36
1
1
1
0
1
X
X
X
1D0000H to 1DFFFFH
0E8000H to 0EFFFFH
SA37
1
1
1
1
0
X
X
X
1E0000H to 1EFFFFH
0F0000H to 0F7FFFH
SA38
1
1
1
1
1
X
X
X
1F0000H to 1FFFFFH
0F8000H to 0FFFFFH
13
MB84VD2118XA-85/MB84VD2119XA-85
Table 3.3 Sector Address Tables (MB84VD21182)
Sector Address
Bank
Bank 2
Bank 1
14
Sector
Bank Address
Address Range
(BYTE mode)
Address Range
(WORD mode)
A19
A18
A17
A16
A15
A14
A13
A12
SA0
0
0
0
0
0
X
X
X
000000H to 00FFFFH
000000H to 007FFFH
SA1
0
0
0
0
1
X
X
X
010000H to 01FFFFH
008000H to 00FFFFH
SA2
0
0
0
1
0
X
X
X
020000H to 02FFFFH
010000H to 017FFFH
SA3
0
0
0
1
1
X
X
X
030000H to 03FFFFH
018000H to 01FFFFH
SA4
0
0
1
0
0
X
X
X
040000H to 04FFFFH
020000H to 027FFFH
SA5
0
0
1
0
1
X
X
X
050000H to 05FFFFH
028000H to 02FFFFH
SA6
0
0
1
1
0
X
X
X
060000H to 06FFFFH
030000H to 037FFFH
SA7
0
0
1
1
1
X
X
X
070000H to 07FFFFH
038000H to 03FFFFH
SA8
0
1
0
0
0
X
X
X
080000H to 08FFFFH
040000H to 047FFFH
SA9
0
1
0
0
1
X
X
X
090000H to 09FFFFH
048000H to 04FFFFH
SA10
0
1
0
1
0
X
X
X
0A0000H to 0AFFFFH
050000H to 057FFFH
SA11
0
1
0
1
1
X
X
X
0B0000H to 0BFFFFH
058000H to 05FFFFH
SA12
0
1
1
0
0
X
X
X
0C0000H to 0CFFFFH
060000H to 067FFFH
SA13
0
1
1
0
1
X
X
X
0D0000H to 0DFFFFH
068000H to 06FFFFH
SA14
0
1
1
1
0
X
X
X
0E0000H to 0EFFFFH
070000H to 077FFFH
SA15
0
1
1
1
1
X
X
X
0F0000H to 0FFFFFH
078000H to 07FFFFH
SA16
1
0
0
0
0
X
X
X
100000H to 10FFFFH
080000H to 087FFFH
SA17
1
0
0
0
1
X
X
X
110000H to 11FFFFH
088000H to 08FFFFH
SA18
1
0
0
1
0
X
X
X
120000H to 12FFFFH
090000H to 097FFFH
SA19
1
0
0
1
1
X
X
X
130000H to 13FFFFH
098000H to 09FFFFH
SA20
1
0
1
0
0
X
X
X
140000H to 14FFFFH
0A0000H to 0A7FFFH
SA21
1
0
1
0
1
X
X
X
150000H to 15FFFFH
0A8000H to 0AFFFFH
SA22
1
0
1
1
0
X
X
X
160000H to 16FFFFH
0B0000H to 0B7FFFH
SA23
1
0
1
1
1
X
X
X
170000H to 17FFFFH
0B8000H to 0BFFFFH
SA24
1
1
0
0
0
X
X
X
180000H to 18FFFFH
0C0000H to 0C7FFFH
SA25
1
1
0
0
1
X
X
X
190000H to 19FFFFH
0C8000H to 0CFFFFH
SA26
1
1
0
1
0
X
X
X
1A0000H to 1AFFFFH
0D0000H to 0D7FFFH
SA27
1
1
0
1
1
X
X
X
1B0000H to 1BFFFFH
0D8000H to 0DFFFFH
SA28
1
1
1
0
0
X
X
X
1C0000H to 1CFFFFH
0E0000H to 0E7FFFH
SA29
1
1
1
0
1
X
X
X
1D0000H to 1DFFFFH
0E8000H to 0EFFFFH
SA30
1
1
1
1
0
X
X
X
1E0000H to 1EFFFFH
0F0000H to 0F7FFFH
SA31
1
1
1
1
1
0
0
0
1F0000H to 1F1FFFH
0F8000H to 0F8FFFH
SA32
1
1
1
1
1
0
0
1
1F2000H to 1F3FFFH
0F9000H to 0F9FFFH
SA33
1
1
1
1
1
0
1
0
1F4000H to 1F5FFFH
0FA000H to 0FAFFFH
SA34
1
1
1
1
1
0
1
1
1F6000H to 1F7FFFH
0FB000H to 0FBFFFH
SA35
1
1
1
1
1
1
0
0
1F8000H to 1F9FFFH
0FC000H to 0FCFFFH
SA36
1
1
1
1
1
1
0
1
1FA000H to 1FBFFFH
0FD000H to 0FDFFFH
SA37
1
1
1
1
1
1
1
0
1FC000H to 1FDFFFH
0FE000H to 0FEFFFH
SA38
1
1
1
1
1
1
1
1
1FE000H to 1FFFFFH
0FF000H to 0FFFFFH
MB84VD2118XA-85/MB84VD2119XA-85
Table 3.4 Sector Address Tables (MB84VD21192)
Sector Address
Bank
Bank 1
Bank 2
Sector
Bank Address
Address Range
(BYTE mode)
Address Range
(WORD mode)
A19
A18
A17
A16
A15
A14
A13
A12
SA0
0
0
0
0
0
0
0
0
000000H to 001FFFH
000000H to 000FFFH
SA1
0
0
0
0
0
0
0
1
002000H to 003FFFH
001000H to 001FFFH
SA2
0
0
0
0
0
0
1
0
004000H to 005FFFH
002000H to 002FFFH
SA3
0
0
0
0
0
0
1
1
006000H to 007FFFH
003000H to 003FFFH
SA4
0
0
0
0
0
1
0
0
008000H to 009FFFH
004000H to 004FFFH
SA5
0
0
0
0
0
1
0
1
00A000H to 00BFFFH
005000H to 005FFFH
SA6
0
0
0
0
0
1
1
0
00C000H to 00DFFFH
006000H to 006FFFH
SA7
0
0
0
0
0
1
1
1
00E000H to 00FFFFH
007000H to 007FFFH
SA8
0
0
0
0
1
X
X
X
010000H to 01FFFFH
008000H to 00FFFFH
SA9
0
0
0
1
0
X
X
X
020000H to 02FFFFH
010000H to 017FFFH
SA10
0
0
0
1
1
X
X
X
030000H to 03FFFFH
018000H to 01FFFFH
SA11
0
0
1
0
0
X
X
X
040000H to 04FFFFH
020000H to 027FFFH
SA12
0
0
1
0
1
X
X
X
050000H to 05FFFFH
028000H to 02FFFFH
SA13
0
0
1
1
0
X
X
X
060000H to 06FFFFH
030000H to 037FFFH
SA14
0
0
1
1
1
X
X
X
070000H to 07FFFFH
038000H to 03FFFFH
SA15
0
1
0
0
0
X
X
X
080000H to 08FFFFH
040000H to 047FFFH
SA16
0
1
0
0
1
X
X
X
090000H to 09FFFFH
048000H to 04FFFFH
SA17
0
1
0
1
0
X
X
X
0A0000H to 0AFFFFH
050000H to 057FFFH
SA18
0
1
0
1
1
X
X
X
0B0000H to 0BFFFFH
058000H to 05FFFFH
SA19
0
1
1
0
0
X
X
X
0C0000H to 0CFFFFH
060000H to 067FFFH
SA20
0
1
1
0
1
X
X
X
0D0000H to 0DFFFFH
068000H to 06FFFFH
SA21
0
1
1
1
0
X
X
X
0E0000H to 0EFFFFH
070000H to 077FFFH
SA22
0
1
1
1
1
X
X
X
0F0000H to 0FFFFFH
078000H to 07FFFFH
SA23
1
0
0
0
0
X
X
X
100000H to 10FFFFH
080000H to 087FFFH
SA24
1
0
0
0
1
X
X
X
110000H to 11FFFFH
088000H to 08FFFFH
SA25
1
0
0
1
0
X
X
X
120000H to 12FFFFH
090000H to 097FFFH
SA26
1
0
0
1
1
X
X
X
130000H to 13FFFFH
098000H to 09FFFFH
SA27
1
0
1
0
0
X
X
X
140000H to 14FFFFH
0A0000H to 0A7FFFH
SA28
1
0
1
0
1
X
X
X
150000H to 15FFFFH
0A8000H to 0AFFFFH
SA29
1
0
1
1
0
X
X
X
160000H to 16FFFFH
0B0000H to 0B7FFFH
SA30
1
0
1
1
1
X
X
X
170000H to 17FFFFH
0B8000H to 0BFFFFH
SA31
1
1
0
0
0
X
X
X
180000H to 18FFFFH
0C0000H to 0C7FFFH
SA32
1
1
0
0
1
X
X
X
190000H to 19FFFFH
0C8000H to 0CFFFFH
SA33
1
1
0
1
0
X
X
X
1A0000H to 1AFFFFH
0D0000H to 0D7FFFH
SA34
1
1
0
1
1
X
X
X
1B0000H to 1BFFFFH
0D8000H to 0DFFFFH
SA35
1
1
1
0
0
X
X
X
1C0000H to 1CFFFFH
0E0000H to 0E7FFFH
SA36
1
1
1
0
1
X
X
X
1D0000H to 1DFFFFH
0E8000H to 0EFFFFH
SA37
1
1
1
1
0
X
X
X
1E0000H to 1EFFFFH
0F0000H to 0F7FFFH
SA38
1
1
1
1
1
X
X
X
1F0000H to 1FFFFFH
0F8000H to 0FFFFFH
15
MB84VD2118XA-85/MB84VD2119XA-85
Table 3.5 Sector Address Tables (MB84VD21183)
Sector Address
Bank
Bank 2
Bank 1
16
Sector
Bank Address
Address Range
(BYTE mode)
Address Range
(WORD mode)
A19
A18
A17
A16
A15
A14
A13
A12
SA0
0
0
0
0
0
X
X
X
000000H to 00FFFFH
000000H to 007FFFH
SA1
0
0
0
0
1
X
X
X
010000H to 01FFFFH
008000H to 00FFFFH
SA2
0
0
0
1
0
X
X
X
020000H to 02FFFFH
010000H to 017FFFH
SA3
0
0
0
1
1
X
X
X
030000H to 03FFFFH
018000H to 01FFFFH
SA4
0
0
1
0
0
X
X
X
040000H to 04FFFFH
020000H to 027FFFH
SA5
0
0
1
0
1
X
X
X
050000H to 05FFFFH
028000H to 02FFFFH
SA6
0
0
1
1
0
X
X
X
060000H to 06FFFFH
030000H to 037FFFH
SA7
0
0
1
1
1
X
X
X
070000H to 07FFFFH
038000H to 03FFFFH
SA8
0
1
0
0
0
X
X
X
080000H to 08FFFFH
040000H to 047FFFH
SA9
0
1
0
0
1
X
X
X
090000H to 09FFFFH
048000H to 04FFFFH
SA10
0
1
0
1
0
X
X
X
0A0000H to 0AFFFFH
050000H to 057FFFH
SA11
0
1
0
1
1
X
X
X
0B0000H to 0BFFFFH
058000H to 05FFFFH
SA12
0
1
1
0
0
X
X
X
0C0000H to 0CFFFFH
060000H to 067FFFH
SA13
0
1
1
0
1
X
X
X
0D0000H to 0DFFFFH
068000H to 06FFFFH
SA14
0
1
1
1
0
X
X
X
0E0000H to 0EFFFFH
070000H to 077FFFH
SA15
0
1
1
1
1
X
X
X
0F0000H to 0FFFFFH
078000H to 07FFFFH
SA16
1
0
0
0
0
X
X
X
100000H to 10FFFFH
080000H to 087FFFH
SA17
1
0
0
0
1
X
X
X
110000H to 11FFFFH
088000H to 08FFFFH
SA18
1
0
0
1
0
X
X
X
120000H to 12FFFFH
090000H to 097FFFH
SA19
1
0
0
1
1
X
X
X
130000H to 13FFFFH
098000H to 09FFFFH
SA20
1
0
1
0
0
X
X
X
140000H to 14FFFFH
0A0000H to 0A7FFFH
SA21
1
0
1
0
1
X
X
X
150000H to 15FFFFH
0A8000H to 0AFFFFH
SA22
1
0
1
1
0
X
X
X
160000H to 16FFFFH
0B0000H to 0B7FFFH
SA23
1
0
1
1
1
X
X
X
170000H to 17FFFFH
0B8000H to 0BFFFFH
SA24
1
1
0
0
0
X
X
X
180000H to 18FFFFH
0C0000H to 0C7FFFH
SA25
1
1
0
0
1
X
X
X
190000H to 19FFFFH
0C8000H to 0CFFFFH
SA26
1
1
0
1
0
X
X
X
1A0000H to 1AFFFFH
0D0000H to 0D7FFFH
SA27
1
1
0
1
1
X
X
X
1B0000H to 1BFFFFH
0D8000H to 0DFFFFH
SA28
1
1
1
0
0
X
X
X
1C0000H to 1CFFFFH
0E0000H to 0E7FFFH
SA29
1
1
1
0
1
X
X
X
1D0000H to 1DFFFFH
0E8000H to 0EFFFFH
SA30
1
1
1
1
0
X
X
X
1E0000H to 1EFFFFH
0F0000H to 0F7FFFH
SA31
1
1
1
1
1
0
0
0
1F0000H to 1F1FFFH
0F8000H to 0F8FFFH
SA32
1
1
1
1
1
0
0
1
1F2000H to 1F3FFFH
0F9000H to 0F9FFFH
SA33
1
1
1
1
1
0
1
0
1F4000H to 1F5FFFH
0FA000H to 0FAFFFH
SA34
1
1
1
1
1
0
1
1
1F6000H to 1F7FFFH
0FB000H to 0FBFFFH
SA35
1
1
1
1
1
1
0
0
1F8000H to 1F9FFFH
0FC000H to 0FCFFFH
SA36
1
1
1
1
1
1
0
1
1FA000H to 1FBFFFH
0FD000H to 0FDFFFH
SA37
1
1
1
1
1
1
1
0
1FC000H to 1FDFFFH
0FE000H to 0FEFFFH
SA38
1
1
1
1
1
1
1
1
1FE000H to 1FFFFFH
0FF000H to 0FFFFFH
MB84VD2118XA-85/MB84VD2119XA-85
Table 3.6 Sector Address Tables (MB84VD21193)
Sector Address
Bank
Bank 1
Bank 2
Sector
Bank Address
Address Range
(BYTE mode)
Address Range
(WORD mode)
A19
A18
A17
A16
A15
A14
A13
A12
SA0
0
0
0
0
0
0
0
0
000000H to 001FFFH
000000H to 000FFFH
SA1
0
0
0
0
0
0
0
1
002000H to 003FFFH
001000H to 001FFFH
SA2
0
0
0
0
0
0
1
0
004000H to 005FFFH
002000H to 002FFFH
SA3
0
0
0
0
0
0
1
1
006000H to 007FFFH
003000H to 003FFFH
SA4
0
0
0
0
0
1
0
0
008000H to 009FFFH
004000H to 004FFFH
SA5
0
0
0
0
0
1
0
1
00A000H to 00BFFFH
005000H to 005FFFH
SA6
0
0
0
0
0
1
1
0
00C000H to 00DFFFH
006000H to 006FFFH
SA7
0
0
0
0
0
1
1
1
00E000H to 00FFFFH
007000H to 007FFFH
SA8
0
0
0
0
1
X
X
X
010000H to 01FFFFH
008000H to 00FFFFH
SA9
0
0
0
1
0
X
X
X
020000H to 02FFFFH
010000H to 017FFFH
SA10
0
0
0
1
1
X
X
X
030000H to 03FFFFH
018000H to 01FFFFH
SA11
0
0
1
0
0
X
X
X
040000H to 04FFFFH
020000H to 027FFFH
SA12
0
0
1
0
1
X
X
X
050000H to 05FFFFH
028000H to 02FFFFH
SA13
0
0
1
1
0
X
X
X
060000H to 06FFFFH
030000H to 037FFFH
SA14
0
0
1
1
1
X
X
X
070000H to 07FFFFH
038000H to 03FFFFH
SA15
0
1
0
0
0
X
X
X
080000H to 08FFFFH
040000H to 047FFFH
SA16
0
1
0
0
1
X
X
X
090000H to 09FFFFH
048000H to 04FFFFH
SA17
0
1
0
1
0
X
X
X
0A0000H to 0AFFFFH
050000H to 057FFFH
SA18
0
1
0
1
1
X
X
X
0B0000H to 0BFFFFH
058000H to 05FFFFH
SA19
0
1
1
0
0
X
X
X
0C0000H to 0CFFFFH
060000H to 067FFFH
SA20
0
1
1
0
1
X
X
X
0D0000H to 0DFFFFH
068000H to 06FFFFH
SA21
0
1
1
1
0
X
X
X
0E0000H to 0EFFFFH
070000H to 077FFFH
SA22
0
1
1
1
1
X
X
X
0F0000H to 0FFFFFH
078000H to 07FFFFH
SA23
1
0
0
0
0
X
X
X
100000H to 10FFFFH
080000H to 087FFFH
SA24
1
0
0
0
1
X
X
X
110000H to 11FFFFH
088000H to 08FFFFH
SA25
1
0
0
1
0
X
X
X
120000H to 12FFFFH
090000H to 097FFFH
SA26
1
0
0
1
1
X
X
X
130000H to 13FFFFH
098000H to 09FFFFH
SA27
1
0
1
0
0
X
X
X
140000H to 14FFFFH
0A0000H to 0A7FFFH
SA28
1
0
1
0
1
X
X
X
150000H to 15FFFFH
0A8000H to 0AFFFFH
SA29
1
0
1
1
0
X
X
X
160000H to 16FFFFH
0B0000H to 0B7FFFH
SA30
1
0
1
1
1
X
X
X
170000H to 17FFFFH
0B8000H to 0BFFFFH
SA31
1
1
0
0
0
X
X
X
180000H to 18FFFFH
0C0000H to 0C7FFFH
SA32
1
1
0
0
1
X
X
X
190000H to 19FFFFH
0C8000H to 0CFFFFH
SA33
1
1
0
1
0
X
X
X
1A0000H to 1AFFFFH
0D0000H to 0D7FFFH
SA34
1
1
0
1
1
X
X
X
1B0000H to 1BFFFFH
0D8000H to 0DFFFFH
SA35
1
1
1
0
0
X
X
X
1C0000H to 1CFFFFH
0E0000H to 0E7FFFH
SA36
1
1
1
0
1
X
X
X
1D0000H to 1DFFFFH
0E8000H to 0EFFFFH
SA37
1
1
1
1
0
X
X
X
1E0000H to 1EFFFFH
0F0000H to 0F7FFFH
SA38
1
1
1
1
1
X
X
X
1F0000H to 1FFFFFH
0F8000H to 0FFFFFH
17
MB84VD2118XA-85/MB84VD2119XA-85
Table 3.7 Sector Address Tables (MB84VD21184)
Sector Address
Bank
Bank 2
Bank 1
18
Sector
Bank Address
Address Range
(BYTE mode)
Address Range
(WORD mode)
A19
A18
A17
A16
A15
A14
A13
A12
SA0
0
0
0
0
0
X
X
X
000000H to 00FFFFH
000000H to 007FFFH
SA1
0
0
0
0
1
X
X
X
010000H to 01FFFFH
008000H to 00FFFFH
SA2
0
0
0
1
0
X
X
X
020000H to 02FFFFH
010000H to 017FFFH
SA3
0
0
0
1
1
X
X
X
030000H to 03FFFFH
018000H to 01FFFFH
SA4
0
0
1
0
0
X
X
X
040000H to 04FFFFH
020000H to 027FFFH
SA5
0
0
1
0
1
X
X
X
050000H to 05FFFFH
028000H to 02FFFFH
SA6
0
0
1
1
0
X
X
X
060000H to 06FFFFH
030000H to 037FFFH
SA7
0
0
1
1
1
X
X
X
070000H to 07FFFFH
038000H to 03FFFFH
SA8
0
1
0
0
0
X
X
X
080000H to 08FFFFH
040000H to 047FFFH
SA9
0
1
0
0
1
X
X
X
090000H to 09FFFFH
048000H to 04FFFFH
SA10
0
1
0
1
0
X
X
X
0A0000H to 0AFFFFH
050000H to 057FFFH
SA11
0
1
0
1
1
X
X
X
0B0000H to 0BFFFFH
058000H to 05FFFFH
SA12
0
1
1
0
0
X
X
X
0C0000H to 0CFFFFH
060000H to 067FFFH
SA13
0
1
1
0
1
X
X
X
0D0000H to 0DFFFFH
068000H to 06FFFFH
SA14
0
1
1
1
0
X
X
X
0E0000H to 0EFFFFH
070000H to 077FFFH
SA15
0
1
1
1
1
X
X
X
0F0000H to 0FFFFFH
078000H to 07FFFFH
SA16
1
0
0
0
0
X
X
X
100000H to 10FFFFH
080000H to 087FFFH
SA17
1
0
0
0
1
X
X
X
110000H to 11FFFFH
088000H to 08FFFFH
SA18
1
0
0
1
0
X
X
X
120000H to 12FFFFH
090000H to 097FFFH
SA19
1
0
0
1
1
X
X
X
130000H to 13FFFFH
098000H to 09FFFFH
SA20
1
0
1
0
0
X
X
X
140000H to 14FFFFH
0A0000H to 0A7FFFH
SA21
1
0
1
0
1
X
X
X
150000H to 15FFFFH
0A8000H to 0AFFFFH
SA22
1
0
1
1
0
X
X
X
160000H to 16FFFFH
0B0000H to 0B7FFFH
SA23
1
0
1
1
1
X
X
X
170000H to 17FFFFH
0B8000H to 0BFFFFH
SA24
1
1
0
0
0
X
X
X
180000H to 18FFFFH
0C0000H to 0C7FFFH
SA25
1
1
0
0
1
X
X
X
190000H to 19FFFFH
0C8000H to 0CFFFFH
SA26
1
1
0
1
0
X
X
X
1A0000H to 1AFFFFH
0D0000H to 0D7FFFH
SA27
1
1
0
1
1
X
X
X
1B0000H to 1BFFFFH
0D8000H to 0DFFFFH
SA28
1
1
1
0
0
X
X
X
1C0000H to 1CFFFFH
0E0000H to 0E7FFFH
SA29
1
1
1
0
1
X
X
X
1D0000H to 1DFFFFH
0E8000H to 0EFFFFH
SA30
1
1
1
1
0
X
X
X
1E0000H to 1EFFFFH
0F0000H to 0F7FFFH
SA31
1
1
1
1
1
0
0
0
1F0000H to 1F1FFFH
0F8000H to 0F8FFFH
SA32
1
1
1
1
1
0
0
1
1F2000H to 1F3FFFH
0F9000H to 0F9FFFH
SA33
1
1
1
1
1
0
1
0
1F4000H to 1F5FFFH
0FA000H to 0FAFFFH
SA34
1
1
1
1
1
0
1
1
1F6000H to 1F7FFFH
0FB000H to 0FBFFFH
SA35
1
1
1
1
1
1
0
0
1F8000H to 1F9FFFH
0FC000H to 0FCFFFH
SA36
1
1
1
1
1
1
0
1
1FA000H to 1FBFFFH
0FD000H to 0FDFFFH
SA37
1
1
1
1
1
1
1
0
1FC000H to 1FDFFFH
0FE000H to 0FEFFFH
SA38
1
1
1
1
1
1
1
1
1FE000H to 1FFFFFH
0FF000H to 0FFFFFH
MB84VD2118XA-85/MB84VD2119XA-85
Table 3.8 Sector Address Tables (MB84VD21194)
Sector Address
Bank
Bank 1
Bank 2
Sector
Bank Address
Address Range
(BYTE mode)
Address Range
(WORD mode)
A19
A18
A17
A16
A15
A14
A13
A12
SA0
0
0
0
0
0
0
0
0
000000H to 001FFFH
000000H to 000FFFH
SA1
0
0
0
0
0
0
0
1
002000H to 003FFFH
001000H to 001FFFH
SA2
0
0
0
0
0
0
1
0
004000H to 005FFFH
002000H to 002FFFH
SA3
0
0
0
0
0
0
1
1
006000H to 007FFFH
003000H to 003FFFH
SA4
0
0
0
0
0
1
0
0
008000H to 009FFFH
004000H to 004FFFH
SA5
0
0
0
0
0
1
0
1
00A000H to 00BFFFH
005000H to 005FFFH
SA6
0
0
0
0
0
1
1
0
00C000H to 00DFFFH
006000H to 006FFFH
SA7
0
0
0
0
0
1
1
1
00E000H to 00FFFFH
007000H to 007FFFH
SA8
0
0
0
0
1
X
X
X
010000H to 01FFFFH
008000H to 00FFFFH
SA9
0
0
0
1
0
X
X
X
020000H to 02FFFFH
010000H to 017FFFH
SA10
0
0
0
1
1
X
X
X
030000H to 03FFFFH
018000H to 01FFFFH
SA11
0
0
1
0
0
X
X
X
040000H to 04FFFFH
020000H to 027FFFH
SA12
0
0
1
0
1
X
X
X
050000H to 05FFFFH
028000H to 02FFFFH
SA13
0
0
1
1
0
X
X
X
060000H to 06FFFFH
030000H to 037FFFH
SA14
0
0
1
1
1
X
X
X
070000H to 07FFFFH
038000H to 03FFFFH
SA15
0
1
0
0
0
X
X
X
080000H to 08FFFFH
040000H to 047FFFH
SA16
0
1
0
0
1
X
X
X
090000H to 09FFFFH
048000H to 04FFFFH
SA17
0
1
0
1
0
X
X
X
0A0000H to 0AFFFFH
050000H to 057FFFH
SA18
0
1
0
1
1
X
X
X
0B0000H to 0BFFFFH
058000H to 05FFFFH
SA19
0
1
1
0
0
X
X
X
0C0000H to 0CFFFFH
060000H to 067FFFH
SA20
0
1
1
0
1
X
X
X
0D0000H to 0DFFFFH
068000H to 06FFFFH
SA21
0
1
1
1
0
X
X
X
0E0000H to 0EFFFFH
070000H to 077FFFH
SA22
0
1
1
1
1
X
X
X
0F0000H to 0FFFFFH
078000H to 07FFFFH
SA23
1
0
0
0
0
X
X
X
100000H to 10FFFFH
080000H to 087FFFH
SA24
1
0
0
0
1
X
X
X
110000H to 11FFFFH
088000H to 08FFFFH
SA25
1
0
0
1
0
X
X
X
120000H to 12FFFFH
090000H to 097FFFH
SA26
1
0
0
1
1
X
X
X
130000H to 13FFFFH
098000H to 09FFFFH
SA27
1
0
1
0
0
X
X
X
140000H to 14FFFFH
0A0000H to 0A7FFFH
SA28
1
0
1
0
1
X
X
X
150000H to 15FFFFH
0A8000H to 0AFFFFH
SA29
1
0
1
1
0
X
X
X
160000H to 16FFFFH
0B0000H to 0B7FFFH
SA30
1
0
1
1
1
X
X
X
170000H to 17FFFFH
0B8000H to 0BFFFFH
SA31
1
1
0
0
0
X
X
X
180000H to 18FFFFH
0C0000H to 0C7FFFH
SA32
1
1
0
0
1
X
X
X
190000H to 19FFFFH
0C8000H to 0CFFFFH
SA33
1
1
0
1
0
X
X
X
1A0000H to 1AFFFFH
0D0000H to 0D7FFFH
SA34
1
1
0
1
1
X
X
X
1B0000H to 1BFFFFH
0D8000H to 0DFFFFH
SA35
1
1
1
0
0
X
X
X
1C0000H to 1CFFFFH
0E0000H to 0E7FFFH
SA36
1
1
1
0
1
X
X
X
1D0000H to 1DFFFFH
0E8000H to 0EFFFFH
SA37
1
1
1
1
0
X
X
X
1E0000H to 1EFFFFH
0F0000H to 0F7FFFH
SA38
1
1
1
1
1
X
X
X
1F0000H to 1FFFFFH
0F8000H to 0FFFFFH
19
MB84VD2118XA-85/MB84VD2119XA-85
Table 4.1 Sector Group Addresses (MB84VD2118XA)
(Top Boot Block)
Sector Group
A19
A18
A17
A16
A15
A14
A13
A12
Sectors
SGA0
0
0
0
0
0
X
X
X
SA0
0
0
0
0
1
X
X
X
0
0
0
1
0
X
X
X
0
0
0
1
1
X
X
X
SGA2
0
0
1
X
X
X
X
X
SA4 to SA7
SGA3
0
1
0
X
X
X
X
X
SA8 to SA11
SGA4
0
1
1
X
X
X
X
X
SA12 to SA15
SGA5
1
0
0
X
X
X
X
X
SA16 to SA19
SGA6
1
0
1
X
X
X
X
X
SA20 to SA23
SGA7
1
1
0
X
X
X
X
X
SA24 to SA27
1
1
1
0
0
X
X
X
1
1
1
0
1
X
X
X
1
1
1
1
0
X
X
X
SGA9
1
1
1
1
1
0
0
0
SA31
SGA10
1
1
1
1
1
0
0
1
SA32
SGA11
1
1
1
1
1
0
1
0
SA33
SGA12
1
1
1
1
1
0
1
1
SA34
SGA13
1
1
1
1
1
1
0
0
SA35
SGA14
1
1
1
1
1
1
0
1
SA36
SGA15
1
1
1
1
1
1
1
0
SA37
SGA16
1
1
1
1
1
1
1
1
SA38
SGA1
SGA8
20
SA1 to SA3
SA28 to SA30
MB84VD2118XA-85/MB84VD2119XA-85
Table 4.2 Sector Group Addresses (MB84VD2119XA)
(Bottom Boot Block)
Sector Group
A19
A18
A17
A16
A15
A14
A13
A12
Sectors
SGA0
0
0
0
0
0
0
0
0
SA0
SGA1
0
0
0
0
0
0
0
1
SA1
SGA2
0
0
0
0
0
0
1
0
SA2
SGA3
0
0
0
0
0
0
1
1
SA3
SGA4
0
0
0
0
0
1
0
0
SA4
SGA5
0
0
0
0
0
1
0
1
SA5
SGA6
0
0
0
0
0
1
1
0
SA6
SGA7
0
0
0
0
0
1
1
1
SA7
0
0
0
0
1
X
X
X
0
0
0
1
0
X
X
X
0
0
0
1
1
X
X
X
SGA9
0
0
1
X
X
X
X
X
SA11 to SA14
SGA10
0
1
0
X
X
X
X
X
SA15 to SA18
SGA11
0
1
1
X
X
X
X
X
SA19 to SA22
SGA12
1
0
0
X
X
X
X
X
SA23 to SA26
SGA13
1
0
1
X
X
X
X
X
SA27 to SA30
SGA14
1
1
0
X
X
X
X
X
SA31 to SA34
1
1
1
0
0
X
X
X
1
1
1
0
1
X
X
X
1
1
1
1
0
X
X
X
1
1
1
1
1
X
X
X
SGA8
SGA15
SGA16
SA8 to SA10
SA35 to SA37
SA38
21
MB84VD2118XA-85/MB84VD2119XA-85
Table 5 Flash Memory Autoselect Codes
Type
Manufacturer’s Code
MB84VD21181A
MB84VD21191A
MB84VD21182A
MB84VD21192A
Device
Code
MB84VD21183A
MB84VD21193A
MB84VD21184A
MB84VD21194A
Sector Group protect
Byte
Word
Byte
Word
Byte
Word
Byte
Word
Byte
Word
Byte
Word
Byte
Word
Byte
Word
A12 to A19
A6
A1
A0
A-1*1
Code (HEX)
X
VIL
VIL
VIL
VIL
04H
X
VIL
VIL
VIH
VIL
36H
X
2236H
X
VIL
VIL
VIH
VIL
39
X
2239H
X
VIL
VIL
VIH
VIL
2D
X
222DH
X
VIL
VIL
VIH
VIL
2E
X
222EH
X
VIL
VIL
VIH
VIL
28H
X
2228H
X
VIL
VIL
VIH
VIL
2BH
X
222BH
X
VIL
VIL
VIH
VIL
33H
X
2233H
X
VIL
VIL
VIH
VIL
35
X
2235H
Sector Group
Address
VIL
VIH
VIL
VIL
01H*2
*1 : A-1 is for Byte mode.
*2 : Output 01H at protected sector address and output 00H at unprotected sector address.
22
MB84VD2118XA-85/MB84VD2119XA-85
Table 6 Flash Memory Command Definitions
Bus
Write
Command
Sequence
First Bus
Write Cycle
Second Bus
Write Cycle
Cycles
Req’d Addr. Data Addr.
Read/Reset (Note 1)
Read/Reset
(Note 1)
Word
Byte
1
3
Word
Autoselect
Chip Erase
Sector Erase
XXXH F0H
555H
AAAH
3
Word
Byte
Word
Byte
Word
Byte
AAH
555H
Byte
Program
Third Bus
Write Cycle
6
6
2AAH
555H
AAH
555H
AAAH
555H
AAAH
555H
AAAH
Addr.


55H
2AAH
AAAH
4

Data
55H
555H
AAH
AAH
AAH
2AAH
555H
2AAH
555H
2AAH
555H
55H
55H
55H
555H
AAAH
(BA)
555H
(BA)
AAAH
555H
AAAH
555H
AAAH
555H
AAAH
Fourth Bus
Read/Write
Cycle
Fifth Bus
Write Cycle
Sixth Bus
Write Cycle
Data Addr. Data Addr. Data Addr. Data







F0H
RA
RD




90H






A0H
PA
PD




80H
80H
555H
AAAH
555H
AAAH
AAH
AAH
2AAH
555H
2AAH
555H
55H
555H
AAAH
10H
55H
SA
30H
Sector Erase Suspend
1
BA
B0H










Sector Erase Resume
1
BA
30H










20H






Set to
Fast Mode
Word
Fast Program
(Note 2)
Word
Reset from
Fast Mode
(Note 2)
Word
Extended
Sector Group
Protection
(Note 3)
Word
Query
(Note 4)
Word
Hi-ROM Entry
Byte
Byte
Byte
Byte
Byte
Word
Byte
Hi-ROM
Program
(Note 5)
Word
Hi-ROM Erase
(Note 5)
Word
Hi-ROM Exit
(Note 5)
Byte
Byte
3
2
2
4
1
3
555H
AAAH
XXXH A0H
BA
90H
XXXH 60H
55H
AAH
555H
AAAH
98H
AAH
555H
4
6
Word
AAAH
555H
AAAH
2AAH
555H
AAH
555H
AAAH
PA
PD








XXXH
F0H
(Note6)








SPA
60H
SPA
40H
SPA
SD














88H






A0H
PA
PD




55H
HRA
30H



2AAH
555H
555H
2AAH
555H
55H
55H
55H
555H
555H
AAAH
555H
55H
2AAH
AAH
AAAH
55H
2AAH
AAH
555H
4
Byte
AAH
AAAH
555H
AAAH
(HRBA)
555H
(HRBA)
AAAH
80H
555H
AAAH
AAH
90H XXXH 00H
2AAH
555H

23
MB84VD2118XA-85/MB84VD2119XA-85
Notes : 1 : Both Read/Reset commands are functionally equivalent, resetting the device to the read mode.
2 : This command is valid while Fast Mode.
3 : This command is valid while RESET = VID.
4 : The valid Address is A0 to A6.
5 : This command is valid while Hi-ROM mode.
6 : The data “00H” is also acceptable.
Address bits A12 to A19 = X = “H” or “L” for all address commands except for Program Address (PA) ,
Sector Address (SA) , and Bank Address (BA) .
Bus operations are defined in Table 2 “User Bus Operations”.
RA = Address of the memory location to be read.
PA = Address of the memory location to be programmed.
Addresses are latched on the falling edge of the write pulse.
SA = Address of the sector to be erased. The combination of A19, A18, A17, A16, A15, A14, A13, and A12 will
uniquely select any sector.
BA = Bank address (A15 to A19)
SPA = Sector group address to be protected. Set sector group address (SGA) and (A6, A1, A0) = (0, 1, 0).
HRA = Address of the Hidden-ROM area.
SPA = Sector group address to be protected. Set sector group address (SGA) and (A6, A1, A0) = (0, 1, 0).
HRA = Address of the Hidden-ROM area.
MB84VD2118XA (Top Boot Type)
Word mode: 0F8000H to 0FFFFFH
Byte mode: 1F0000H to 1FFFFFH
MB84VD2119XA (Bottom Boot Type) Word mode: 000000H to 007FFFH
Byte mode: 000000H to 00FFFFH
HRBA = Bank addrss of the Hidden-ROM area.
MB84VD2118XA (Top Boot Type)
: A15 = A16 = A17 = A18 = A19 = A20 = 1
MB84VD2119XA (Bottom Boot Type) : A15 = A16 = A17 = A18 = A19 = A20 = 0
RD = Data read from location RA during read operation.
PD = Data to be programmed at location PA.
SD = Sector protection verify data. Output 01H at protected sector addresses and output 00H
at unprotectedsector addresses.
The system should generate the following address patterns;
Word mode : 555H or 2AAH to addresses A0 to A10
Byte mode : AAAH or 555H to addresses A -1 and A0 to A10
24
MB84VD2118XA-85/MB84VD2119XA-85
■ ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Rating
Unit
Min.
Max.
Tstg
−55
+125
°C
TA
−25
+85
°C
VIN, VOUT
−0.3
VCCf, VCCs
−0.3
+4.0
V
A9 and OE (Note 2)
VIN
−0.3
+13.0
V
RESET (Note 2)
VIN
−0.5
+13.0
V
WP/ACC (Note 3)
VIN
−0.5
+10.5
V
Storage Temperature
Ambient Temperature with Power
Applied
Voltage with Respect to Ground All
pins except A9, OE, RESET,
WP/ACC (Note 1)
VCCf/VCCs Supply (Note 1)
VCCf + 0.4
VCCs + 0.4
V
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
Notes 1. Minimum DC voltage on input or I/O pins is –0.3 V. During voltage transitions, input or I/O pins may
undershoot VSS to –2.0 V for periods of up to 20 ns. Maximum DC voltage on input or I/O pins is VCCf
+0.4 V or VCCs+0.4 V. During voltage transitions, input or I/O pins may overshoot to VCCf+2.0 V or VCCs+2.0
V for periods of up to 20 ns.
2. Minimum DC input voltage on A9 and OE pin is –0.3 V. Minimum DC input voltage on RESET pin is
–0.5 V. During voltage transitions, A9, OE, and RESET pins may undershoot VSS to –2.0 V for periods of
up to 20 ns.
Voltage difference between input and supply voltage (VIN-VCCf or VCCs) does not exceed 9.0 V.
Maximum DC input voltage on A9, OE, and RESET pins is +13.0 V which may overshoot to 14.0 V for
periods of up to 20 ns.
3. Minimum DC input voltage on WP/ACC pin is –0.5 V. During voltage transitions, WP/ACC pin may
undershoot Vss to –2.0 V for periods of up to 20 ns. Maximum DC input voltage on WP/ACC pin is +10.5
V which may overshoot to 12.0 V for periods of up to 20 ns, when VCCf is applied.
■ RECOMMENDED OPERATING CONDITIONS
Parameter
Ambient Temperature
VCCf/VCCs Supply Voltages
Symbol
Value
Unit
Min.
Max.
TA
−25
+85
°C
VCCf, VCCs
+2.7
+3.6
V
Operating ranges define those limits between which the functionality of the device is guaranteed.
WARNING: The recommended operating conditions are required in order to ensure the normal operation of the
semiconductor device. All of the device’s electrical characteristics are warranted when the device is
operated within these ranges.
Always use semiconductor devices within their recommended operating condition ranges. Operation
outside these ranges may adversely affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented on
the data sheet. Users considering application outside the listed conditions are advised to contact their
FUJITSU representatives beforehand.
25
MB84VD2118XA-85/MB84VD2119XA-85
■ ELECTRICAL CHARACTERISTICS
1. DC Characteristics
Parameter
Symbol
26
Parameter Description
Test Conditions
Min.
Typ.
Max.
Unit
ILI
Input Leakage Current
VIN = VSS to VCCf, VCCs
−1.0

+1.0
µA
ILO
Output Leakage Current
VOUT = VSS to VCCf, VCCs
−1.0

+1.0
µA
ILIT
RESET Inputs Leakage
Current
VCCf = VCCf Max, VCCs = VCCs Max,
RESET = 12.5V


35
µA
ILIA
ACC Input Leakage
Current
VCCf = VCCf Max, VCCs = VCCs Max,
WP/ACC = VACC Max


20
mA
tCYCLE = 5 MHz Byte


13
ICC1f
Flash VCC Active Current
(Read)
(Note 1)
tCYCLE = 5 MHz Word


15
tCYCLE = 1 MHz Byte


7
tCYCLE = 1 MHz Word


7


35
Byte


48
Word


50
Byte


48
Word


50


35
mA


40
mA
tCYCLE = 10 MHz


40
mA
tCYCLE = 1 MHz


8
mA
CEf = VIL,
OE = VIH
mA
mA
ICC2f
Flash VCC Active Current
(Program/Erase)
(Note 2)
CEf = VIL, OE = VIH
ICC3f
Flash VCC Active Current
(Read-While-Program)
(Note 5)
CEf = VIL, OE = VIH
ICC4f
Flash VCC Active Current
(Read-While-Erase)
(Note 5)
CEf = VIL, OE = VIH
ICC5f
Flash VCC Active Current
(Erase-Suspend-Program)
CEf = VIL, OE = VIH
ICC1s
VCCs = VCC Max.,
SRAM VCC Active Current CE1s = VIL,
tCYCLE = 10 MHz
CE2s = VIH
ICC2s
CE1s = 0.2 V,
SRAM VCC Active Current CE2s = VCCs −
0.2 V,
ISB1f
Flash VCC Standby Current
VCCf = VCC Max., CEf = VCCf ± 0.3 V
RESET = VCCf ± 0.3 V,
WP/ACC = VCCf ± 0.3 V

1
5
µA
ISB2f
Flash VCC Standby Current (RESET)
VCCf = VCC Max., RESET = VSS ± 0.3 V
WP/ACC = VCCf ± 0.3 V

1
5
µA
ISB3f
Flash VCC Current
(Automatic Sleep Mode)
(Note 3)
VCCf = VCC Max., CEf = VSS ± 0.3 V
RESET = VCCf ± 0.3 V,
WP/ACC = VCCf ± 0.3 V
VIN = VCCf ± 0.3 V or VSS ± 0.3 V

1
5
µA
ISB1s
SRAM VCC Standby
Current
CE1s ≥ VCCs − 0.2V,
CE2s ≥ VCCs − 0.2V

0.2
7
µA
ISB2s
SRAM VCC Standby
Current
CE2s ≤ 0.2V

0.2
7
µA
mA
mA
mA
MB84VD2118XA-85/MB84VD2119XA-85
(Continued)
(Continued)
Parameter
Symbol
Parameter Description
Test Conditions
Min.
Typ.
Max.
Unit
VIL
Input Low Level

−0.3

0.5
V
VIH
Input High Level

2.4

VCC +
0.3*
V
VID
Voltage for Sector
Protection, and Temporary
Sector Unprotection
(RESET) (Note 4)

11.5

12.5
V
VACC
Voltage for Program
Acceleration (WP/ACC)
(Note4)

8.5
9.0
9.5
V
VOL
Output Low Voltage Level
VCCf = VCCf Min., VCCs = VCCs Min.,
IOL = 1.0 mA


0.4
V
VOH
Output High Voltage Level
VCCf = VCCf Min., VCCs = VCCs Min.,
IOH = −0.5 mA
2.4


V
VLKO
Flash Low VCCf Lock-Out
Voltage
2.3

2.5
V

*: VCC indicates lower of VCCf or VCCs.
Notes : 1. The ICC current listed includes both the DC operating current and the frequency dependent component.
2. ICC active while Embedded Algorithm (program or erase) is in progress.
3. Automatic sleep mode enables the low power mode when address remain stable for 150ns.
4. Applicable for only VCCf applying.
5. Embedded Alogorithm (program or erase) is in progress. (@5MHz)
27
MB84VD2118XA-85/MB84VD2119XA-85
2. AC Characteristics
• CE Timing
Parameter
Symbols
JEDEC
Standard

tCCR
Description
Test Setup

CE Recover Time
Min.
• Timing Diagram for alternating SRAM to Flash
CEf
tCCR
tCCR
tCCR
tCCR
CE1s
CE2s
28
-85
Unit
0
ns
MB84VD2118XA-85/MB84VD2119XA-85
• Read Only Operations Characteristics (Flash)
Parameter
Symbols
Description
JEDEC Standard
Test
Setup
-85
(Note)
Unit
Min.
Max.

85

ns
tAVAV
tRC
Read Cycle Time
tAVQV
tACC
Address to Output Delay
CEf = VIL
OE = VIL

85
ns
tELQV
tCEf
Chip Enable to Output Delay
OE = VIL

85
ns
tGLQV
tOE
Output Enable to Output Delay


35
ns
tEHQZ
tDF
Chip Enable to Output High-Z


30
ns
tGHQZ
tDF
Output Enable to Output High-Z


30
ns
tAXQX
tOH
Output Hold Time From Addresses,
CEf or OE, Whichever Occurs First

0

ns

tREADY
RESET Pin Low to Read Mode


20
µs
Note : Test Conditions − Output Load : 1 TTL gate and 30 pF
Input rise and fall times : 5 ns
Input pulse levels : 0.0 V to 3.0 V
Timing measurement reference level
Input : 1.5 V
Output : 1.5 V
29
MB84VD2118XA-85/MB84VD2119XA-85
• Read Cycle (Flash)
tRC
Addresses Stable
Addresses
tACC
CEf
tDF
tOE
OE
tOEH
WE
tCEf
HIGH-Z
DQ
HIGH-Z
Output Valid
tRC
Addresses
Addresses Stable
tRH
tACC
CEf
tRP
tRH
tCEf
RESET
tOH
HIGH-Z
DQ
30
Output Valid
MB84VD2118XA-85/MB84VD2119XA-85
• Erase/Program Operations (Flash)
Parameter Symbols
JEDEC
Standard
tAVAV
tWC
tAVWL
Description
-85
Unit
Min.
Typ.
Max.
Write Cycle Time
85


ns
tAS
Address Setup Time (WE to Addr.)
0


ns

tASO
Address Setup Time to CEf Low During Toggle Bit Polling
15


ns
tWLAX
tAH
Address Hold Time (WE to Addr.)
45


ns

tAHT
Address Hold Time from CEf or OE High During Toggle Bit
Polling
0


ns
tDVWH
tDS
Data Setup Time
35


ns
tWHDX
tDH
Data Hold Time
0


ns

tOES
Output Enable Setup Time
0


ns

tOEH
Output Enable Hold Time
Read
0


ns
Toggle and Data Polling
10


ns

tCEPH
CEf High During Toggle Bit Polling
20


ns

tOEPH
OE High During Toggle Bit Polling
20


ns
tGHEL
tGHEL
Read Recover Time Before Write (OE to CEf)
0


ns
tGHWL
tGHWL
Read Recover Time Before Write (OE to WE)
0


ns
tWLEL
tWS
WE Setup Time (CEf to WE)
0


ns
tELWL
tCS
CEf Setup Time (WE to CEf)
0


ns
tEHWH
tWH
WE Hold Time (CEf to WE)
0


ns
tWHEH
tCH
CEf Hold Time (WE to CEf)
0


ns
tWLWH
tWP
Write Pulse Width
35


ns
tELEH
tCP
CEf Pulse Width
35


ns
tWHWL
tWPH
Write Pulse Width High
30


ns
tEHEL
tCPH
CEf Pulse Width High
30


ns
tWHWH1
tWHWH1
Byte Programming Operation

8

µs
Word Programming Operation

16

µs
tWHWH2
tWHWH2
Sector Erase Operation (Note 1)

1

s
(Continued)
31
MB84VD2118XA-85/MB84VD2119XA-85
(Continued)
Parameter Symbols
JEDEC
Standard

tVCS

Description
-85
Unit
Min.
Typ.
Max.
VCCf Setup Time
50


µs
tVLHT
Voltage Transition Time (Note 2)
4


µs

tVIDR
Rise Time to VID (Note 2)
500


ns

tVACCR
Rise Time to VACC
500


ns

tRB
Recover Time from RY/BY
0


ns

tRP
RESET Pulse Width
500


ns

tEOE
Delay Time from Embedded Output Enable


85
ns

tRH
RESET Hold Time Before Read
200


ns

tBUSY
Program/Erase Valid to RY/BY Delay


90
ns

tTOW
Erase Time-out Time (Note 3)
50


µs

tSPD
Erase Suspend Transition Time (Note 4)


20
µs
Notes : 1. This does not include the preprogramming time.
2. This timing is for Sector Protection Operation.
3. The time between writes must be less than “tTOW” otherwise that command will not be accepted and
erasure will start. A time-out or “tTOW” from the rising edge of last CEf or WE whichever happens first will
initiate the execution of the Sector Erase command (s) .
4. When the Erase Suspend command is written during the Sector Erase operation, the device will take a
maximum of “tSPD” to suspend the erase operation.
32
MB84VD2118XA-85/MB84VD2119XA-85
• Write Cycle (WE control) (Flash)
3rd Bus Cycle
Addresses
Data Polling
555H
tWC
PA
tAS
PA
tRC
tAH
CEf
tCS
tCH
tCEf
OE
tGHWL
tWP
tOE
tWHWH1
tWPH
WE
tOH
tDS
tDH
DQ
A0H
PD
DQ7
DOUT
DOUT
Notes : 1. PA is address of the memory location to be programmed.
2. PD is data to be programmed at byte address.
3. DQ7 is the output of the complement of the data written to the device.
4. DOUT is the output of the data written to the device.
5. Figure indicates last two bus cycles out of four bus cycle sequence.
6. These waveforms are for the × 16 mode. (The addresses differ from × 8 mode.)
33
MB84VD2118XA-85/MB84VD2119XA-85
• Write Cycle (CEf control) (Flash)
3rd Bus Cycle
Addresses
Data Polling
555H
tWC
PA
tAS
PA
tAH
WE
tWS
tWH
OE
tGHEL
tCP
tWHWH1
tCPH
CEf
tDS
tDH
DQ
A0H
PD
DQ7
DOUT
Notes : 1. PA is address of the memory location to be programmed.
2. PD is data to be programmed at byte address.
3. DQ7 is the output of the complement of the data written to the device.
4. DOUT is the output of the data written to the device.
5. Figure indicates last two bus cycles out of four bus cycle sequence.
6. These waveforms are for the × 16 mode. (The addresses differ from × 8 mode.)
34
MB84VD2118XA-85/MB84VD2119XA-85
• AC Waveforms Chip/Sector Erase Operations (Flash)
555H
Addresses
tWC
2AAH
tAS
555H
555H
2AAH
SA*
tAH
CEf
tCS
tCH
OE
tGHWL
tWP
tWPH
WE
tDS
tDH
AAH
30H for Sector Erase
55H
80H
AAH
55H
DQ
10H/
30H
tVCS
VCCf
* : SA is the sector address for Sector Erase. Addresses = 555H for Chip Erase.
Note : These waveforms are for the × 16 mode. (The addresses differ from × 8 mode.)
35
MB84VD2118XA-85/MB84VD2119XA-85
• AC Waveforms for Data Polling during Embedded Algorithm Operations (Flash)
CEf
tCH
tDF
tOE
OE
tOEH
WE
tCEf
*
DQ7
Data In
DQ7 =
Valid Data
DQ7
High-Z
tWHWH1 or 2
DQ
(DQ0 to DQ6)
Data In
DQ0 to DQ6 = Output Flag
tBUSY
tEOE
RY/BY
* : DQ7 = Valid Data (The device has completed the Embedded operation.)
36
DQ0 to DQ6
Valid Data
High-Z
MB84VD2118XA-85/MB84VD2119XA-85
• AC Waveforms for Toggle Bit during Embedded Algorithm Operations (Flash)
Addresses
tAHT tASO
tAHT tAS
CEf
tCEPH
WE
tOEPH
tOEH
tOEH
OE
tDH
DQ6/DQ2
Toggle
Data
Data
tCEf*
tOE
Toggle
Data
Toggle
Data
Stop
Toggling
Output
Valid
tBUSY
RY/BY
* : DQ6 stops toggling (The device has completed the Embedded operation) .
37
MB84VD2118XA-85/MB84VD2119XA-85
• Back-to-back Read/Write Timing Diagram (Flash)
Address
Read
Command
Read
Command
Read
Read
tRC
tWC
tRC
tWC
tRC
tRC
BA1
BA2
(555H)
BA1
BA2
(PA)
BA1
BA2
(PA)
tAS
tAS
tACC
tAH
tAHT
tCEf
CEf
tOE
tCEPH
OE
tGHWL
tOEH
tDF
tWP
WE
tDS
DQ
Valid
Output
tDH
Valid
Input
(A0H)
tDF
Valid
Output
Valid
Input
Valid
Output
Status
(PD)
Note : This is example of Read for Bank 1 and Embedded Algorithm (program) for Bank 2.
BA1 : Address of Bank 1.
BA2 : Address of Bank 2.
38
MB84VD2118XA-85/MB84VD2119XA-85
• RY/BY Timing Diagram during Write/Erase Operations (Flash)
CEf
The rising edge of the last write pulse
WE
Entire programming
or erase operations
RY/BY
tBUSY
• RESET, RY/BY Timing Diagram (Flash)
WE
RESET
tRP
tRB
RY/BY
tREADY
39
MB84VD2118XA-85/MB84VD2119XA-85
• Temporary Sector Unprotection (Flash)
VCCf
tVIDR
tVLHT
tVCS
VID
3V
3V
RESET
CEf
WE
tVLHT
tVLHT
Program or Erase Command Sequence
RY/BY
Unprotection Period
40
MB84VD2118XA-85/MB84VD2119XA-85
• Extended Sector Protection (Flash)
VCCf
tVCS
RESET
tVLHT
tVIDR
tWC
tWC
SGAx
Addresses
SGAx
SGAy
A0
A1
A6
CEf
OE
TIME - OUT
tWP
WE
Data
60H
60H
40H
01H
60H
tOE
SGAx : Sector Group Address to be protected
SGAy : Next Group Sector Address to be protected
TIME-OUT : Time-Out window = 250 µs (min.)
41
MB84VD2118XA-85/MB84VD2119XA-85
• Accelerated Program (Flash)
VCC
tVACCR
tVCS
tVLHT
VACC
3V
3V
WP/ACC
CE
WE
tVLHT
Program or Erase Command Sequence
RY/BY
Acceleration period
42
tVLHT
MB84VD2118XA-85/MB84VD2119XA-85
• Read Cycle (SRAM)
Parameter
Symbol
Parameter Description
Min.
Max.
Unit
tRC
Read Cycle Time
85

ns
tAA
Address Access Time

85
ns
tCO1
Chip Enable (CE1s) Access Time

85
ns
tCO2
Chip Enable (CE2s) Access Time

85
ns
tOE
Output Enable Access Time

45
ns
tBA
LBS, UBS to Output Valid

85
ns
tCOE
Chip Enable (CE1s Low and CE2s High) to Output Active
5

ns
tOEE
Output Enable Low to Output Active
0

ns
tBE
UBS, LBS Enable Low to Output Active
0

ns
tOD
Chip Enable (CE1s High or CE2s Low) to Output High-Z

35
ns
tODO
Output Enable High to Output High-Z

35
ns
tBD
UBS, LBS Output Enable to Output High-Z

50
ns
tOH
Output Data Hold Time
10

ns
43
MB84VD2118XA-85/MB84VD2119XA-85
• Read Cycle (Note) (SRAM)
tRC
ADDRESSES
tAA
tOH
tCO1
CE1s
tCOE
tOD
tCO2
CE2s
tOD
tOE
OE
tODO
tOEE
LBS, UBS
tBA
tBD
tBE
tCOE
DQ
Note : WE remains HIGH for the read cycle.
44
VALID DATA OUT
MB84VD2118XA-85/MB84VD2119XA-85
• Write Cycle (SRAM)
Parameter
Symbol
Parameter Description
Min.
Max.
Unit
tWC
Write Cycle Time
85

ns
tWP
Write Pulse Width
55

ns
tCW
Chip Enable to End of Write
70

ns
tAW
Address valid to End of Write
70

ns
tBW
UBS, LBS to End of Write
55

ns
tAS
Address Setup Time
0

ns
tWR
Write Recovery Time
0

ns
tODW
WE Low to Output High-Z

35
ns
tOEW
WE High to Output Active
0

ns
tDS
Data Setup Time
35

ns
tDH
Data Hold Time
0

ns
45
MB84VD2118XA-85/MB84VD2119XA-85
• Write Cycle (Note 3) (WE control) (SRAM)
tWC
Addresses
tAS
tWP
tWR
WE
tAW
tCW
CE1s
CE2s
tCW
tBW
LBS, UBS
tODW
DOUT
tOEW
Note 1
Note 2
tDS
DIN
Note 4
tDH
VALID DATA IN
Note 4
Notes : 1. If CE1s goes LOW (or CE2s goes HIGH) coincident with or after WE goes LOW, the
output will remain at high impedance.
2. If CE1s goes HIGH (or CE2s goes LOW) coincident with or before WE goes HIGH, the
output will remain at high impedance.
3. If OE is HIGH during the write cycle, the outputs will remain at high impedance.
4. Because I/O signals may be in the output state at this time, input signals of reverse
polarity must not be applied.
46
MB84VD2118XA-85/MB84VD2119XA-85
• Write Cycle (Note 1) (CE1s control) (SRAM)
tWC
Addresses
tAS
tWR
tWP
WE
tAW
tCW
CE1s
CE2s
tCW
tBW
LBS, UBS
tBE
tCOE
tODW
DOUT
tDS
DIN
Note 2
tDH
VALID DATA IN
Notes : 1. If OE is HIGH during the write cycle, the outputs will remain at high impedance.
2. Because I/O signals may be in the output state at this time, input signals of reverse
polarity must not be applied.
47
MB84VD2118XA-85/MB84VD2119XA-85
• Write Cycle (Note 1) (CE2s Control) (SRAM)
tWC
Addresses
tAS
tWP
tWR
WE
tCW
CE1s
tAW
CE2s
tCW
tBW
LBS, UBS
tBE
tCOE
tODW
DOUT
tDS
DIN
Note 2
tDH
VALID DATA IN
Notes : 1. If OE is HIGH during the write cycle, the outputs will remain at high impedance.
2. Because I/O signals may be in the output state at this time, input signals of reverse
polarity must not be applied.
48
MB84VD2118XA-85/MB84VD2119XA-85
• Write Cycle (Note 1) (LBs, UBs Control) (SRAM)
tWC
Addresses
tWP
tWR
WE
tCW
CE1s
tCW
CE2s
tAW
tAS
tBW
LBS, UBS
tBE
tCOE
tODW
DOUT
tDS
DIN
Note 2
tDH
VALID DATA IN
Notes : 1. If OE is HIGH during the write cycle, the outputs will remain at high impedance.
2. Because I/O signals may be in the output state at this time, input signals of reverse
polarity must not be applied.
49
MB84VD2118XA-85/MB84VD2119XA-85
■ ERASE AND PROGRAMMING PERFORMANCE (Flash)
Limits
Parameter
Unit
Comment
Min.
Typ.
Max.
Sector Erase Time

1
10
s
Excludes programming time
prior to erasure
Byte Programming Time

8
300
µs
Excludes system-level
overhead
Word Programming Time

16
360
µs
Excludes system-level
overhead
Chip Programming Time


50
s
Excludes system-level
overhead
100,000


cycle
Erase/Program Cycle
■ DATA RETENTION CHARACTERISTICS (SRAM)
Parameter
Symbol
Parameter Description
Min.
Typ.
Max.
Unit
1.5

3.6
V

0.2
7*
µA
VDH
Data Retention Supply Voltage
IDDS2
Standby Current
tCDR
Chip Deselect to Data Retention Mode Time
0


ns
Recovery Time
tRC


ns
tR
VDH = 3.0 V
Note : tRC : Read cycle time
* : 4 µA Max. at TA ≤ 60 °C, 1 µA Max. at TA ≤ 40 °C
• CE1s Controlled Data Retention Mode (Note 1)
VCCs
DATA RETENTION MODE
2.7 V
See Note 2
VIH
VDH
CE1s
GND
50
tCDR
See Note 2
VCCS −0.2 V
tR
MB84VD2118XA-85/MB84VD2119XA-85
• CE2s Controlled Data Retention Mode (Note 3)
VCCs
DATA RETENTION MODE
2.7 V
VDH
VIH
CE2s
tCDR
tR
VIL
0.2 V
GND
Notes : 1. In CE1s controlled data retention mode, input level of CE2s should be fixed Vccs to Vccs − 0.2 V or Vss
to 0.2 V during data retention mode. Other input and input/output pins can be used between −0.3 V and
Vccs + 0.3 V.
2. When CE1s is operating at the VIH min. level (2.2 V) , the standby current is given by ISB1s during the
transition of VCCs from 3.6 to 2.2 V.
3. In CE2s controlled data retention mode, input and input/output pins can be used between −0.3 V and
Vccs + 0.3 V.
■ PIN CAPACITANCE
Parameter
Symbol
Parameter Description
Test Setup
Typ.
Max.
Unit
CIN
Input Capacitance
VIN = 0
11
14
pF
COUT
Output Capacitance
VOUT = 0
12
16
pF
CIN2
Control Pin Capacitance
VIN = 0
14
16
pF
CIN3
WP/ACC Pin Capacitance
VIN = 0
17
20
pF
Note : Test conditions TA = 25 °C, f = 1.0 MHz
■ HANDLING OF PACKAGE
Please handle this package carefully since the sides of packages are right angle.
■ CAUTION
1. The high voltage (VID) can not apply to address pins and control pins except RESET. Therefore, it can not
use autoselect and sector protect function by applying the high voltage (VID) to specific pins.
2. For the sector protection, since the high voltage (VID) can be applied to the RESET, it can be protected the
sector using “Extended sector protect” command.
51
MB84VD2118XA-85/MB84VD2119XA-85
■ ORDERING INFORMATION
MB84VD2118
X
A
-85
-PBS
PACKAGE TYPE
PBS = 69-ball FBGA
PTS = 56-pin TSOP (I)
SPEED OPTION
See Product Selector Guide.
Device Revision
Bank Size
1 = 0.5 Mbit / 15.5 Mbit
2 = 2 Mbit / 14 Mbit
3 = 4 Mbit / 12 Mbit
4 = 8 Mbit /
8 Mbit
DEVICE NUMBER/DESCRIPTION
16Mega-bit (2M × 8-bit or 1M × 16-bit) Dual Operation Flash Memory
3.0 V-only Read, Program, and Erase
4Mega-bit (512K × 8-bit) SRAM
BOOT CODE SECTOR ARCHITECTURE
84VD2118 = Top sector
84VD2119 = Bottom sector
52
MB84VD2118XA-85/MB84VD2119XA-85
■ PACKAGE DIMENSIONS
69-ball plastic FBGA
(BGA-69P-M02)
7.20(.283)
11.00±0.10(.433±.004)
1.25
+0.15
–0.10
+.006
–.004
5.60(.220)REF
(Mounting height)
.049
0.38±0.10
(Stand off)
(.015±.004)
0.80(.031)
10
9
8
0.80(.031)
8.00±0.10
(.315±.004)
7
6
5.60(.220)
REF
7.20(.283)
5
4
3
2
1
K
J
H G
F
E
D C
B
A
INDEX-MARK AREA
INDEX BALL
+0.10
69-Ø0.45 –0.05
+.004
69-Ø0.18 –.002
0.08(.003)
M
0.10(.004)
C
1999 FUJITSU LIMITED B69002S-1C-1
Dimension in mm (inches)
(Continued)
53
MB84VD2118XA-85/MB84VD2119XA-85
(Continued)
56-pin plastic TSOP (I)
(FPT-56P-M04)
14.00±0.20(.551±.008)
12.40±0.10(.488±.004)
INDEX
0.40(.016)
TYP
12.00±0.10
(.472±.004)
0.18±0.035
(.007±.001)
"A"
0.10(.004)
M
Details of "A" part
0.25(.010)
+0.05
0.145 –0.03
.006
C
+.002
–.001
0.08(.003)
1.15±0.05
0.10±0.05
(.045±.002)
(.004±.002) (Mounting height)
(Stand off)
0°~8°
0.45/0.75
(.018/.030)
1998 FUJITSU LIMITED F56004S-1C-1
Dimension in mm (inches)
54
MB84VD2118XA-85/MB84VD2119XA-85
FUJITSU LIMITED
For further information please contact:
Japan
FUJITSU LIMITED
Corporate Global Business Support Division
Electronic Devices
KAWASAKI PLANT, 4-1-1, Kamikodanaka,
Nakahara-ku, Kawasaki-shi,
Kanagawa 211-8588, Japan
Tel: +81-44-754-3763
Fax: +81-44-754-3329
http://www.fujitsu.co.jp/
North and South America
FUJITSU MICROELECTRONICS, INC.
3545 North First Street,
San Jose, CA 95134-1804, U.S.A.
Tel: +1-408-922-9000
Fax: +1-408-922-9179
Customer Response Center
Mon. - Fri.: 7 am - 5 pm (PST)
Tel: +1-800-866-8608
Fax: +1-408-922-9179
http://www.fujitsumicro.com/
Europe
FUJITSU MICROELECTRONICS EUROPE GmbH
Am Siebenstein 6-10,
D-63303 Dreieich-Buchschlag,
Germany
Tel: +49-6103-690-0
Fax: +49-6103-690-122
http://www.fujitsu-fme.com/
Asia Pacific
FUJITSU MICROELECTRONICS ASIA PTE. LTD.
#05-08, 151 Lorong Chuan,
New Tech Park,
Singapore 556741
Tel: +65-281-0770
Fax: +65-281-0220
http://www.fmap.com.sg/
Korea
FUJITSU MICROELECTRONICS KOREA LTD.
1702 KOSMO TOWER, 1002 Daechi-Dong,
Kangnam-Gu,Seoul 135-280
Korea
Tel: +82-2-3484-7100
Fax: +82-2-3484-7111
F0007
 FUJITSU LIMITED Printed in Japan
All Rights Reserved.
The contents of this document are subject to change without notice.
Customers are advised to consult with FUJITSU sales
representatives before ordering.
The information and circuit diagrams in this document are
presented as examples of semiconductor device applications, and
are not intended to be incorporated in devices for actual use. Also,
FUJITSU is unable to assume responsibility for infringement of
any patent rights or other rights of third parties arising from the use
of this information or circuit diagrams.
The contents of this document may not be reproduced or copied
without the permission of FUJITSU LIMITED.
FUJITSU semiconductor devices are intended for use in standard
applications (computers, office automation and other office
equipments, industrial, communications, and measurement
equipments, personal or household devices, etc.).
CAUTION:
Customers considering the use of our products in special
applications where failure or abnormal operation may directly
affect human lives or cause physical injury or property damage, or
where extremely high levels of reliability are demanded (such as
aerospace systems, atomic energy controls, sea floor repeaters,
vehicle operating controls, medical devices for life support, etc.)
are requested to consult with FUJITSU sales representatives before
such use. The company will not be responsible for damages arising
from such use without prior approval.
Any semiconductor devices have inherently a certain rate of failure.
You must protect against injury, damage or loss from such failures
by incorporating safety design measures into your facility and
equipment such as redundancy, fire protection, and prevention of
over-current levels and other abnormal operating conditions.
If any products described in this document represent goods or
technologies subject to certain restrictions on export under the
Foreign Exchange and Foreign Trade Control Law of Japan, the
prior authorization by Japanese government should be required for
export of those products from Japan.
Similar pages