Fujitsu MB89677ARPFM 8-bit proprietary microcontroller Datasheet

FUJITSU SEMICONDUCTOR
DATA SHEET
DS07-12537-1E
8-bit Proprietary Microcontroller
CMOS
F2MC-8L MB89670R/670AR Series
MB89673R/673AR/675R/675AR
MB89677AR/P677A/PV670A
■ OUTLINE
The MB89670R/670AR series has been developed as a line of proprietary 8-bit, single-chip microcontrollers.
In addition to the F2MC*-8L family CPU core which can operate at low voltage but at high speed, the
microcontrollers contain pheripheral functions such as timers, a serial interface, a 10-bit A/D converter, a UART,
an 8/16-bit up/down counter/timer, and an external interrupt.
The MB89670R/670AR series is applicable to a wide range of applications from consumer appliances to
industrial equipment, including portable devices.
*: F2MC stands for FUJITSU Flexible Microcontroller.
■ FEATURES
• F2MC-8L family CPU core
Instruction set optimized for controllers
Multiplication and division instructions
16-bit arithmetic operations
Test and branch instructions
Bit manipulation instructions, etc.
• High-speed processing at low voltage
• Minimum execution time: 0.4 µ[email protected] V, 0.8 µ[email protected] V, 2.0 µ[email protected] V
• I/O ports: max. 69 channels
(Continued)
■ PACKAGE
80-pin Plastic QFP
(FPT-80P-M06)
(FPT-80P-M06)
80-pin Plastic LQFP
(FPT-80P-M11)
(FPT-80P-M11)
80-pin Ceramic MQFP
(MQP-80C-P01)
(MQP-80C-P01)
MB89670R/670AR Series
(Continued)
• Timers: 9 channels (MB89675AR/677AR/P677A/PV670A: 12 channels)
8-bit PWM timer: 3 channels (MB89675AR/677AR/P677A/PV670A: 6 channels) (also usable as a reload
timer or 8-bit PWM timer)
16-bit timer/counter
21-bit timebase timer
8/16-bit timer (8 bits × 2 channels or 16 bits)
8/16-bit up/down counter/timer (8 bits × 2 channels or 16 bits)
• 2-channel serial interfaces
8-bit synchronized serial: 1 channel (Switchable transfer direction allows communication with various
equipment.)
UART: 1 channel (internal full-duplex double buffer)
• External interrupts: 8 channels
Eight channels are independent and capable of wake-up from low-power consumption modes (with an edge
detection function).
• Buzzer output
• 10-bit A/D converter
Input: 8 channels
• Low-power consumption modes
Stop mode (Oscillation stops to minimize the current consumption.)
Sleep mode (The CPU stops to reduce the current consumption to approx. 1/3 of normal.)
• Bus interface function
Including hold and ready functions
2
MB89670R/670AR Series
■ PRODUCT LINEUP
Part number
MB89673R*1 MB89673AR MB89675R*1 MB89675AR MB89677AR MB89P677A MB89PV670A
Item
Classification
One-time
PROM
product (for
development)
Mass-produced products
(mask ROM products)
ROM size
8 K × 8 bits
(internal mask ROM)
16 K × 8 bits
(internal mask ROM)
RAM size
384 × 8 bits
512 × 8 bits
32 K × 8 bits
(internal mask ROM)
Piggyback/
evaluation
product (for
development)
48 K × 8 bits
(external
ROM)
1 K × 8 bits
CPU
functions
The number of instructions:
Instruction bit length:
Instruction length:
Data bit length:
Minimum execution time:
Interrupt processing time:
136
8 bits
1 to 3 bytes
1, 8, 16 bits
0.4 µs@10 MHz to 6.4 µs@10 MHz
3.6 µs@10 MHz to 57.6 µs@10 MHz
Ports
Output ports (N-channel open-drain):
Output ports (CMOS):
I/O ports (N-channel open-drain):
I/O ports (CMOS):
Input ports:
Total:
14 (12 also serve as peripherals.)
8 (All also serve as peripherals.)
7 (All also serve as peripherals.)
32 (All also serve as peripherals.)
8 (All also serve as peripherals.)
69
Option
Specify when ordering masking
Timebase
timer
Set with
EPROM
programmer
21 bits (0.81 ms, 3.27 ms, 26.21 ms, 419 ms@10 MHz)
8/16-bit
up/down
counter/timer
8 bits × 2 channels or 16 bits × 1 channel
Timer operation
Up/down counter operation
Phase difference counting (double mode, quadruple mode)
16-bit
timer/counter
16-bit timer operation
16-bit event counter operation (edge selectable)
8/16-bit
timer/counter
8 bits × 2 channels or 16 bits × 1 channel
Reload timer operation (toggled output capable)
Event counter operation
8-bit PWM
timer 1, 2
Setting not
possible
8 bits × 2 channels reload timer operation (toggled output capable)
8 bits × 2 channels PWM operation (four frequencies fixed)
8 bits × 1 channel PPG operation (variable frequency)
Capable of output switching between 2 channels in any mode
8-bit PWM
timer 3, 4, 5, 6
8-bit reload timer operation (toggled output capable)
8-bit PWM operation (four frequencies fixed)
Capable of output switching between 2 channels in any mode
8-bit serial I/O
8 bits
LSB first/MSB first selectable
One clock selectable from four transfer clocks
(one external shift clock, three internal shift clocks)
(Continued)
3
MB89670R/670AR Series
(Continued)
Part number
MB89673R*1 MB89673AR MB89675R*1 MB89675AR MB89677AR MB89P677A MB89PV670A
Item
UART
Variable data length (7 or 8 bits)
On-chip baud rate generator
Error detection function
On-chip full-duplex double buffer
NRZ transfer format
CLK synchrnous/asynchronous data transfer capable
10-bit A/D
converter
10 bits × 8 channels
External
interrupt
8 channels (Rising edge/falling edge)
Power supply
voltage*2
2.2 V to 6.0 V
EPROM for
use
2.7 V to 6.0 V
MBM27C512
-20TV
—
*1: 8-bit PWM timer 4, 5, and 6 are not provided for the MB89673R/MB89675R.
*2: The minimum operating voltage varies with the operating frequency, the function, and the connected ICE.
■ PACKAGE AND CORRESPONDING PRODUCTS
MB89673R
MB89675R
Package
MB89673AR
MB89675AR
MB89677AR
MB89P677A
MB89PV670A
FPT-80P-M06
×
FPT-80P-M11
×*
MQP-80C-P01
: Available
×
×
×
× : Not available
* : Lead pitch converter sockets (manufacturer: Sun Hayato Co., Ltd.) are available
80QF-80QF2-8L-UP
+ (MQP-80C-P01 or FPT-80P-M06) → for conversion to FPT-80P-M11
80QF-80QF2-8L-DWN
Inquiry: Sun Hayato Co., Ltd.: TEL: (81)-3-3986-0403
FAX: (81)-3-5396-9106
Note: For more information about each package, see section “■ Package Dimensions.”
4
MB89670R/670AR Series
■ DIFFERENCES AMONG PRODUCTS
1. Memory Size
Before evaluating using the piggyback product, make sure of its differences from the product that will actually
be used. Take particular care on the following points:
• On the MB89P677A, the program area starts from address 8007H, while on the MB89677AR and MB89PV670A
starts from 8000H.
(On the MB89P677A, the option setting data can be read by reading the addresses “8000H” to “8006H”, while
on the MB89677AR and MB89PV670A, addresses 8000H to 8006H could also be used as a program ROM.
However, do not use these addresses in order to maintain compatibility of the MB89P677A.)
• The stack area, etc., is set at the upper limit of the RAM.
• The external area is used.
2. Current Consumption
• In the case of the MB89PV670A, add the current consumed by the EPROM which is connected to the top socket.
• When operated at low speed, the product with an OTPROM (one-time PROM) or an EPROM will consume
more current than the product with a mask ROM.
However, the current consumption in sleep/stop modes is the same. (For more information, see sections
“■ Electrical Characteristics” and “■ Example Characteristics.”)
3. Mask Options
Functions that can be selected as options and how to designate these options vary by the product.
Before using options check section “■ Mask Options.”
Take particular care on the following point:
• Options are fixed on the MB89PV670A.
4. Differences between the MB89670/670A and MB89670R/670AR Series
• Memory access area
Memory access area of both the MB89677A and MB89677AR is the same.
The access are of the MB89673 is different from that of the MB89673R and MB89673AR respectively in the
external bus mode. See below.
Memory area
Address
MB89673
MB89673R/673AR
0000H to 007FH
I/O area
I/O area
0080H to 01FFH
RAM area
RAM area
0200H to 027FH
0280H to BFFFH
Access prohibited
External area
C000H to DFFFH
E000H to FFFFH
External area
Access prohibited
ROM area
ROM area
5
MB89670R/670AR Series
• Electrical specifications/characteristics
Electrical specifications/characteristics of the MB89673R/673AR/677AR are the same with that of the
MB89670/670A series.
• The other specifications
Both the MB89673R/673AR/677AR and the MB89670/670A series are the same.
■ CORRESPONDENCE BETWEEN THE MB89670/670A SERIES AND MB89670R/670AR
SERIES
• The MB89670R/670AR series is the reduction version of the MB89670/670A series.
• The MB89670/670A and MB89670R/670AR sereis consist of the following products:
MB89670/
670A series
MB89670R/
670AR series
MB89673
—
—
—
MB89677A
MB89P677A MB89PV670A
MB89673R MB89673AR MB89675R MB89675AR MB89677AR
• Differences between the MB89670A/670AR series and MB89670/670R series
8-bit PWM timer 4, 5, and 6 is not provided for the MB89670/670R series.
See the table below for the provided 8-bit PWM timer and the corresponding pin for the MB89670A/670AR
series and MB89670/670R series.
Function
6
Pin name for MB89670A/670AR series
Pin name for MB89670/670R series
8-bit PWM timer 1
P40/PWM00
P40/PWM00, P41/PWM01
8-bit PWM timer 2
P42/PWM10/BZ2
P42/PWM10/BZ2, P43/PWM11
8-bit PWM timer 3
P30/PWM20
P30/PWM20, P31/PWM21
8-bit PWM timer 4
P31/PWM21
—
8-bit PWM timer 5
P41/PWM01
—
8-bit PWM timer 6
P43/PWM11
—
MB89670R/670AR Series
■ PIN ASSIGNMENT
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
P74/SCK
P75/SO
P76/SI
AVSS
AVR
AVCC
P50/AN0
P51/AN1
P52/AN2
P53/AN3
P54/AN4
P55/AN5
P56/AN6
P57/AN7
P60/INT0/ADST
P61/INT1
P62/INT2
P63/INT3
P64/INT4
P65/INT5
(Top view)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
P66/INT6
P67/INT7
P84
P85
VSS
P40/PWM00
P41/PWM01
VCC
P42/PWM10/BZ2
P43/PWM11
P44/TCI
P45/TCO1
P46/TCO2
P47/EC
P30/PWM20
P31/PWM21
P32/UDZ1
P33/UDB1
P34/UDA1
P35/UDZ2
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
P21/HAK
P20/BUFC
P17/A15
P16/A14
P15/A13
P14/A12
P13/A11
P12/A10
P11/A09
P10/A08
P07/AD7
P06/AD6
P05/AD5
P04/AD4
P03/AD3
P02/AD2
P01/AD1
P00/AD0
P37/UDA2
P36/UDB2
P73/UI
P72/UO
P71/UCK
P70/BZ1
P83
P82
P81
P80
MOD0
MOD1
X0
X1
VSS
RST
P27/ALE
P26/RD
P25/WR
P24/CLK
P23/RDY
P22/HRQ
(FPT-80P-M11)
7
MB89670R/670AR Series
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
P76/SI
AVSS
AVR
AVCC
P50/AN0
P51/AN1
P52/AN2
P53/AN3
P54/AN4
P55/AN5
P56/AN6
P57/AN7
P60/INT0/ADST
P61/INT1
P62/INT2
P63/INT3
(Top view)
100
99
98
97
96
95
94
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
93
92
91
90
89
88
87
86
85
110
111
112
81
82
83
84
101
102
103
104
105
106
107
108
109
Each pin inside the dashed line
is for the MB89PV670A only.
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
P64/INT4
P65/INT5
P66/INT6
P67/INT7
P84
P85
VSS
P40/PWM00
P41/PWM01
VCC
P42/PWM10/BZ2
P43/PWM11
P44/TCI
P45/TCO1
P46/TCO2
P47/EC
P30/PWM20
P31/PWM21
P32/UDZ1
P33/UDB1
P34/UDA1
P35/UDZ2
P36/UDB2
P37/UDA2
P17/A15
P16/A14
P15/A13
P14/A12
P13/A11
P12/A10
P11/A09
P10/A08
P07/AD7
P06/AD6
P05/AD5
P04/AD4
P03/AD3
P02/AD2
P01/AD1
P00/AD0
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
P75/SO
P74/SCK
P73/UI
P72/UO
P71/UCK
P70/BZ1
P83
P82
P81
P80
MOD0
MOD1
X0
X1
VSS
RST
P27/ALE
P26/RD
P25/WR
P24/CLK
P23/RDY
P22/HRQ
P21/HAK
P20/BUFC
(FPT-80P-M06)
(MQP-80C-P01)
• Pin assignment on package top (MB89PV670A only)
Pin no.
Pin name
Pin no.
Pin name
Pin no.
Pin name
Pin no.
Pin name
81
N.C.
89
A2
97
N.C.
105
OE/VPP
82
A15
90
A1
98
O4
106
N.C.
83
A12
91
A0
99
O5
107
A11
84
A7
92
N.C.
100
O6
108
A9
85
A6
93
O1
101
O7
109
A8
86
A5
94
O2
102
O8
110
A13
87
A4
95
O3
103
CE
111
A14
88
A3
96
VSS
104
A10
112
VCC
N.C.: Internally connected. Do not use.
8
MB89670R/670AR Series
■ PIN DESCRIPTION
Pin no.
Pin name
LQFP*1
QFP*2
MQFP*3
11
13
X0
12
14
X1
Circuit
type
Function
A
Clock oscillator pins
B
Operating mode selection pins
Connect directly to VCC or VSS.
9
11
MOD0
10
12
MOD1
14
16
RST
C
Reset I/O pin
This pin is of a N-ch open-drain output type with pull-up
resistor and a hysteresis input type.
“L” is output from this pin by an internal reset source.
The internal circuit is initialized by the input of “L”.
38 to 31
40 to 33
P00/AD0 to
P07/AD7
D
General-purpose I/O ports
When an external bus is used, these ports function as
multiplex pins of lower address output and data I/O.
30 to 23
32 to 25
P10/A08 to
P17/A15
D
General-purpose I/O ports
When an external bus is used, these ports function as
upper address output pins.
22
24
P20/BUFC
F
General-purpose output port
When an external bus is used, this port can also be
used as a buffer control output by setting the BCTR.
21
23
P21/HAK
F
General-purpose output port
When an external bus is used, this port can also be
used as a hold acknowledge output by setting the
BCTR.
20
22
P22/HRQ
D
General-purpose output port
When an external bus is used, this port can also be
used as a hold request input by setting the BCTR.
19
21
P23/RDY
D
General-purpose output port
When an external bus is used, this port functions as a
ready input.
18
20
P24/CLK
F
General-purpose output port
When an external bus is used, this port functions as a
clock output.
17
19
P25/WR
F
General-purpose output port
When an external bus is used, this port functions as a
write signal output.
16
18
P26/RD
F
General-purpose output port
When an external bus is used, this port functions as a
read signal output.
15
17
P27/ALE
F
General-purpose output port
When an external bus is used, this port functions as an
address latch signal output.
*1: FPT-80P-M11
*2: FPT-80P-M06
*3: MQP-80C-P01
(Continued)
9
MB89670R/670AR Series
Pin no.
Circuit
type
Function
QFP*2
MQFP*3
46
48
P30/PWM20
D
General-purpose I/O port
Also serves as the PWM20 output for the 8-bit PWM
timer.
45
47
P31/PWM21
D
General-purpose I/O port
Also serves as the PWM21 output for the 8-bit PWM
timer.
44
46
P32/UDZ1
E
General-purpose I/O port
Also serves as the Z-phase input for the 8/16-bit
up/down counter/timer.
43
45
P33/UDB1
E
General-purpose I/O port
Also serves as the B-phase input for the 8/16-bit
up/down counter/timer.
42
44
P34/UDA1
E
General-purpose I/O ports
Also serves as the A-phase input for the 8/16-bit
up/down counter/timer.
41
43
P35/UDZ2
E
General-purpose I/O port
Also serves as the Z-phase input for the 8/16-bit
up/down counter/timer.
40
42
P36/UDB2
E
General-purpose I/O port
Also serves as the B-phase input for the 8/16-bit
up/down counter/timer.
39
41
P37/UDA2
E
General-purpose I/O port
Also serves as the A-phase input for the 8/16-bit
up/down counter/timer.
55
57
P40/PWM00
D
General-purpose I/O port
Also serves as the PWM00 output for the 8-bit PWM
timer.
54
56
P41/PWM01
D
General-purpose I/O port
Also serves as the PWM01 output for the 8-bit PWM
timer.
52
54
P42/PWM10/
BZ2
D
General-purpose I/O port
Also serves as the PWM10 and the BZ2 output for the
8-bit PWM timer.
51
53
P43/PWM11
D
General-purpose I/O port
Also serves as the PWM11 output for the 8-bit PWM
timer.
50
52
P44/TCI
E
General-purpose I/O port
Also serves as the TCI input for the 8/16-bit
timer/counter.
49
51
P45/TCO1
D
General-purpose I/O port
Also serves as the TCO1 output for the 8/16-bit
timer/counter.
48
50
P46/TCO2
D
General-purpose I/O port
Also serves as the TCO2 output for the 8/16-bit
timer/counter.
*1: FPT-80P-M11
*2: FPT-80P-M06
*3: MQP-80C-P01
10
Pin name
LQFP*1
(Continued)
MB89670R/670AR Series
(Continued)
Pin no.
LQFP*1
QFP*2
MQFP*3
47
49
74 to 67
76 to 69
66
68
65 to 59
67 to 61
4
Pin name
Circuit
type
Function
P47/EC
E
General-purpose I/O port
Also serves as the input for the16-bit timer/counter.
The EC input is of a hysteresis input type.
P50/AN0 to
P57/AN7
I
N-ch open-drain output ports
Also serve as the analog inputs for the 10-bit A/D
converter.
P60/INT0/
ADST
J
General-purpose input port
The software pull-up resistor is provided.
Also serves as an external interrupt input (INT0) and an
10-bit A/D converter external start-up.
This port is of a hysteresis input type.
P61/INT1 to
P67/INT7
J
General-purpose input ports
A software pull-up resistor is provided.
Also serve as external interrupt inputs (INT1 to INT7).
These ports are of a hysteresis input type.
6
P70/BZ1
G
N-ch open-drain I/O port
Also serves as a buzzer output.
3
5
P71/UCK
K
N-ch open-drain I/O port
Also serves as a UART clock I/O (UCK), switchable to
CMOS.
2
4
P72/UO
K
N-ch open-drain I/O port
Also serves as a UART data output (UO), switchable to
CMOS.
1
3
P73/UI
G
N-ch open-drain I/O port
Also serves as a UART data input (UI).
80
2
P74/SCK
K
N-ch open-drain I/O port
Also serves as the clock I/O (SCK) for the 8-bit serial I/O,
switchable to CMOS.
79
1
P75/SO
K
N-ch open-drain I/O port
Also serves as the data output (SO) for the 8-bit serial
I/O, switchable to CMOS.
78
80
P76/SI
G
N-ch open-drain I/O port
Also serves as the data input (SI) for the 8-bit serial I/O.
8 to 5,
57,
58
10 to 7,
59,
60
P80 to P83,
P85,
P84
H
N-ch open-drain output ports
53
55
VCC
—
Power supply pin
13,
56
15,
58
VSS
—
Power supply (GND) pin
75
77
AVCC
—
A/D converter power supply pin
Use this pin at the same voltage as VCC.
76
78
AVR
—
A/D converter reference voltage input pin
77
79
AVSS
—
A/D converter power supply pin
Use this pin at the same voltage as VSS.
*1: FPT-80P-M11
*2: FPT-80P-M06
*3: MQP-80C-P01
11
MB89670R/670AR Series
• External EPROM pins (MB89PV670A only)
Pin no.
12
Pin name
I/O
Function
82
83
84
85
86
87
88
89
90
91
A15
A12
A7
A6
A5
A4
A3
A2
A1
A0
O
Address output pins
93
94
95
O1
O2
O3
I
Data input pins
96
VSS
O
Power supply (GND) pin
98
99
100
101
102
O4
O5
O6
O7
O8
I
Data input pins
103
CE
O
ROM chip enable pin
Outputs “H” during standby.
104
A10
O
Address output pin
105
OE/VPP
O
ROM output enable pin
Outputs “L” at all times.
107
108
109
A11
A9
A8
O
Address output pins
110
A13
O
111
A14
O
112
VCC
O
81
92
97
106
N.C.
—
Internally connected pins
Be sure to leave them open.
MB89670R/670AR Series
■ I/O CIRCUIT TYPE
Type
A
Circuit
Remarks
• Crystal or ceramic oscillation type
• Oscillation feedback resistor of approximately
1 MΩ at 5.0 V
X1
X0
Standby control signal
B
C
• Output pull-up resistor (P-ch) of approximately
50 kΩ at 5.0 V
• Hysteresis input
R
P-ch
N-ch
D
• CMOS output
• CMOS inout
R
P-ch
P-ch
N-ch
• Pull-up resistor optional (except P22 and P23)
E
• CMOS output
• CMOS input
• The peripheral is of a hysteresis input type.
R
P-ch
P-ch
N-ch
Peripheral
Port
• Pull-up resistor optional
(Continued)
13
MB89670R/670AR Series
(Continued)
Type
Circuit
Remarks
F
• CMOS output
P-ch
N-ch
G
• N-ch open-drain output
• Hysteresis input
R
P-ch
P-ch
N-ch
• Pull-up resistor optional
H
• N-ch open-drain output
N-ch
I
• N-ch open-drain output
• Analog input
P-ch
N-ch
Analog input
J
• Hysteresis input
• With software pull-up resistor
R
P-ch
Pull-up control
signal
K
• CMOS output
• Hysteresis input
R
P-ch
P-ch
N-ch
• Pull-up resistor optional
14
MB89670R/670AR Series
■ HANDLING DEVICES
1. Preventing Latchup
Latchup may occur on CMOS ICs if voltage higher than VCC or lower than VSS is applied to input and output pins
other than medium- and high-voltage pins or if higher than the voltage which shows on “1. Absolute Maximum
Ratings” in section “■ Electrical Characteristics” is applied between VCC and VSS.
When latchup occurs, power supply current increases rapidly and might thermally damage elements. When
using, take great care not to exceed the absolute maximum ratings.
Also, take care to prevent the analog power supply (AVCC and AVR) and analog input from exceeding the digital
power supply (VCC) when the analog system power supply is turned on and off.
2. Treatment of Unused Input Pins
Leaving unused input pins open could cause malfunctions. They should be connected to a pull-up or pull-down
resistor.
3. Treatment of Power Supply Pins on Microcontrollers with A/D and D/A Converters
Connect to be AVCC = DAVC = VCC and AVSS = AVR = VSS even if the A/D and D/A converters are not in use.
4. Treatment of N.C. Pins
Be sure to leave (internally connected) N.C. pins open.
5. Power Supply Voltage Fluctuations
Although VCC power supply voltage is assured to operate within the rated range, a rapid fluctuation of the voltage
could cause malfunctions, even if it occurs within the rated range. Stabilizing voltage supplied to the IC is therefore
important. As stabilization guidelines, it is recommended to control power so that VCC ripple fluctuations (P-P
value) will be less than 10% of the standard VCC value at the commercial frequency (50 Hz to 60 Hz) and the
transient fluctuation rate will be less than 0.1 V/ms at the time of a momentary fluctuation such as when power
is switched.
6. Precautions when Using an External Clock
When an external clock is used, oscillation stabilization time is required even for power-on reset (optional) and
wake-up from stop mode.
15
MB89670R/670AR Series
■ PROGRAMMING TO THE EPROM ON THE MB89P677A
The MB89P677A is an OTPROM version of the MB89670R/670AR series.
1. Features
• 32-Kbyte PROM on chip
• Options can be set using the EPROM programmer.
• Equivalency to the MBM27C256A in the EPROM mode (when programmed with the EPROM programmer)
2. Memory Space
Memory space in the EPROM mode is diagrammed below.
Address
Single chip
0000H
EPROM mode
(Corresponding addresses on the EPROM programmer)
I/O
0080H
RAM
0480H
External area
8000H
0000H
Option area
Not available
8007H
0007H
PROM
32 KB
FFFFH
16
EPROM
32 KB
7FFFH
MB89670R/670AR Series
3. Programming to the EPROM
In EPROM mode, the MB89P677A functions equivalent to the MBM27C256A. This allows the PROM to be
programmed with a general-purpose EPROM programmer (the electronic signature mode cannot be used) by
using the dedicated socket adapter.
• Programming procedure
(1) Set the EPROM programmer to the MBM27C256A.
(2) Load program data into the EPROM programmer at 0007H to 7FFFH (note that addresses 8007H to FFFFH
while operating as a single chip assign to 0007H to 7FFFH in the EPROM mode).
Load option data into addresses 0000H to 0006H of the EPROM programmer. (For information about each
corresponding option, see “7. Setting OTPROM Options.”)
(3) Program with the EPROM programmer.
4. Recommended Screening Conditions
High-temperature aging is recommended as the pre-assembly screening procedure for a product with a blanked
OTPROM microcomputer program.
Program, verify
Aging
+150°C, 48 Hrs.
Data verification
Assembly
5. Programming Yield
Due to the nature of the blanked OTPROM microcomputer, bit programming test can’t be conducted as Fujitsu’s
shipping test. Therefore a programming yield of 100% cannot be assured at all times.
6. EPROM Programmer Socket Adapter
Part number
Package
Compatible socket adapter
Sun Hayato Co., Ltd.
MB89P677APF
MB89P677PFM
QFP-80
QFP-80
ROM-80QF-28DP-8L2
ROM-80QF2-28DP-8L
Inquiry: Sun Hayato Co., Ltd.: TEL: (81)-3-3986-0403
FAX: (81)-3-5396-9106
Note: Depending on the EPROM programmer, inserting a capacitor of about 0.1 µF between VPP and VSS or
VCC and VSS can stabilize programming operations.
17
MB89670R/670AR Series
7. Setting OTPROM Options
The programming procedure is the same as that for the PROM.
Options can be set by programming values at the addresses shown on the memory map. The relationship
between bits and options is shown on the following bit map:
• OTPROM option bit map
Address
Bit 7
Bit 6
Bit 5
Bit 4
Vacancy
Vacancy
Vacancy
Vacancy
Readable
Readable
Readable
Readable
0001H
P17
Pull-up
1: No
0: Yes
P16
Pull-up
1: No
0: Yes
P15
Pull-up
1: No
0: Yes
0002H
P37
Pull-up
1: No
0: Yes
P36
Pull-up
1: No
0: Yes
0003H
P47
Pull-up
1: No
0: Yes
0000H
0004H
0005H
0006H
Bit 3
Bit 1
Bit 0
Reset pin
output
1: Yes
0: No
Power-on
reset
1: Yes
0: No
Oscillation stabilization time
00: 24/FC
10: 217/FC
01: 214/FC
11: 218/FC
P14
Pull-up
1: No
0: Yes
P13
Pull-up
1: No
0: Yes
P12
Pull-up
1: No
0: Yes
P11
Pull-up
1: No
0: Yes
P10
Pull-up
1: No
0: Yes
P35
Pull-up
1: No
0: Yes
P34
Pull-up
1: No
0: Yes
P33
Pull-up
1: No
0: Yes
P32
Pull-up
1: No
0: Yes
P31
Pull-up
1: No
0: Yes
P30
Pull-up
1: No
0: Yes
P46
Pull-up
1: No
0: Yes
P45
Pull-up
1: No
0: Yes
P44
Pull-up
1: No
0: Yes
P43
Pull-up
1: No
0: Yes
P42
Pull-up
1: No
0: Yes
P41
Pull-up
1: No
0: Yes
P40
Pull-up
1: No
0: Yes
Vacancy
Vacancy
Vacancy
Vacancy
Vacancy
Vacancy
Vacancy
Vacancy
Readable
Readable
Readable
Readable
Readable
Readable
Readable
Readable
Vacancy
Vacancy
Vacancy
Readable
Readable
Readable
P74
Pull-up
1: No
0: Yes
P73
Pull-up
1: No
0: Yes
P72
Pull-up
1: No
0: Yes
P71
Pull-up
1: No
0: Yes
P70
Pull-up
1: No
0: Yes
Vacancy
Vacancy
Vacancy
Vacancy
Readable
Readable
Readable
Readable
P04 to P07
Pull-up
1: No
0: Yes
P00 to P03
Pull-up
1: No
0: Yes
P76
Pull-up
1: No
0: Yes
P75
Pull-up
1: No
0: Yes
Notes: • Each bit is set to “1” as the initialized value.
• Do not write “0” to the vacant bit.
The read value of the vacant bit is “1”, unless “0” is written to it.
18
Bit 2
MB89670R/670AR Series
■ PROGRAMMING TO THE EPROM WITH PIGGYBACK/EVALUATION DEVICE
1. EPROM for Use
MBM27C512-20TV
2. Programming Socket Adapter
To program to the PROM using an EPROM programmer, use the socket adapter (manufacturer: Sun Hayato
Co., Ltd.) listed below.
Package
LCC-32(Rectangle)
Adapter socket part number
ROM-32LC-28DP-YG
Inquiry: Sun Hayato Co., Ltd.: TEL: (81)-3-3986-0403
FAX: (81)-3-5396-9106
3. Memory Space
Memory space in each mode is diagrammed below.
Address
Single chip
EPROM mode
(Corresponding address on the EPROM programmer)
0000H
0000H
I/O
0080H
Not available
RAM
0480H
External area
4000H
8000H
4000H
8000H
*
8007H
*
8007H
PROM
48 KB
FFFFH
EPROM
48 KB
FFFFH
*: Note: For the MB89P677A, this area is an option setting area.
4. Programming to the EPROM
(1) Set the EPROM programmer to the MBM27C512.
(2) Load program data into the EPROM programmer at 4000H to FFFFH.
(3) Program to 4000H to FFFFH with the EPROM programmer.
19
MB89670R/670AR Series
■ BLOCK DIAGRAM
1. Block Diagram of MB89673R/89675R
X0
X1
Timebase timer
Oscillator
Clock controller
CMOS I/O port
16-bit up/down
counter/timer
Reset circuit
(WDT)
Internal data bus
RST
RAM
8-bit up/down
counter/timer
P37/UDA2
P36/UDB2
P35/UDZ2
8-bit up/down
counter/timer
P34/UDA1
P33/UDB1
P32/UDZ1
F2MC-8L
CPU
16-bit timer/counter
P47/EC
ROM
8/16-bit timer
CMOS I/O port
8
P00/AD0 to
P07/AD7
16
8
P46/TCO2
8-bit timer
P45/TCO1
P44/TCI
2-channel 8-bit
PWM timer
P10/A08 to
P17/A15
MOD0
MOD1
External bus
interface
8-bit timer #2
8-bit timer #1
P27/ALE
P26/RD
P25/WR
P24/CLK
P23/RDY
P22/HRQ
P21/HAK
P20/BUFC
P31/PWM21
P30/PWM20
CMOS output port
N-ch open-drain
output port
P80 to P85
8
8-bit serial I/O
P76/SI
P75/SO
P74/SCK
UART
P73/UI
P72/UO
P71/UCK
Buzzer output
P70/BZ1
8
10-bit A/D converter
AVR
AVCC
AVSS
Input port
P60/INT0/ADST to
P67/INT7
8
The other pins
VCC, VSS,
MOD0, MOD1
20
P43/PWM11
P42/PWM10/BZ2
P41/PWM01
P40/PWM00
8-bit PWM timer #3
6
P50/AN0 to
P57/AN7
8-bit timer
N-ch open-drain I/O port
8
External interrupt
MB89670R/670AR Series
2. Block Diagram of MB89673AR /89675AR/89677AR/89P677A/89PV670A
Timebase timer
X0
X1
Oscillator
CMOS I/O port
Clock controller
Reset circuit
(WDT)
RST
RAM
F2MC-8L
CPU
Internal data bus
16-bit up/down
counter/timer
8-bit up/down
counter/timer
P37/UDA2
P36/UDB2
P35/UDZ2
8-bit up/down
counter/timer
P34/UDA1
P33/UDB1
P32/UDZ1
16-bit timer/counter
P47/EC
8/16-bit timer
ROM
CMOS I/O port
8-bit timer
P46/TCO2
8-bit timer
P45/TCO1
P44/TCI
8
P00/AD0 to
P07/AD7
16
8-bit PWM timer #3
P30/PWM20
8-bit PWM timer #4
P31/PWM21
8-bit PWM timer #5
P41/PWM01
8-bit PWM timer #6
P43/PWM11
8
P10/A08 to
P17/A15
MOD0
MOD1
External bus
interface
P27/ALE
P26/RD
P25/WR
P24/CLK
P23/RDY
P22/HRQ
P21/HAK
P20/BUFC
2-channel 8-bit
PWM timer
8-bit timer #1
CMOS output port
6
P80 to P85
P50/AN0 to
P57/AN7
8
N-ch open-drain
output port
8-bit timer #2
8-bit serial I/O
P76/SI
P75/SO
P74/SCK
UART
P73/UI
P72/UO
P71/UCK
Buzzer output
P70/BZ1
8
10-bit AD converter
AVR
AVCC
AVSS
P40/PWM00
P42/PWM10/BZ2
Input port
P60/INT0/ADST to
P67/INT7
8
8
External interrupt
N-ch open-drain I/O port
The other pins
VCC, VSS,
MOD0, MOD1
21
MB89670R/670AR Series
■ CPU CORE
1. Memory Space
The microcontrollers of the MB89670R/670AR series offer 64 Kbytes of memory for storing all of I/O, data, and
program areas. The I/O area is allocated at the lowest address. The data area is allocated immediately above
the I/O area. The data area can be divided into register, stack, and direct areas according to the application.
The program area is allocated from exactly the opposite end of I/O area, that is, near the highest address. The
tables of interrupt reset vectors and vector call instructions are allocated from the highest address within the
program area. The memory space of the MB89670R/670AR series is structured as illustrated below.
• Memory Space
MB89675R
MB89675AR
MB89673R
MB89673AR
0000H
0000H
0080H
0100H
I/O
RAM
0080H
0100H
Register 384 B
0000H
I/O
0080H
RAM
0100H
Register 512 B
0200H
0200H
MB89677AR
MB89P677A
MB89PV670A
0000H
I/O
RAM
0080H
0100H
Register 1 KB
I/O
RAM
1 KB
Register
0200H
0200H
0480H
0480H
Not available
0280H
0280H
External area
External area
4000H
External area
External area
8000H
8000H
*
8007H
8007H
Option PROM (One-time
PROM product)*
*
8007H
8007H
External area
External area
C000H
8000H
8000H
*
C000H
Not available
ROM
16 KB
E000H
Programmable
ROM
32 KB
Programmable
ROM
48 KB
ROM
8 KB
FFFFH
FFFFH
FFFFH
FFFFH
*: Since addresses 8000H to 8006H for the MB89P677A comprise an option area, pay attention to
use this area for the other products in this series.
22
MB89670R/670AR Series
2. Registers
The F2MC-8L family has two types of registers; dedicated hardware registers in the CPU and general-purpose
registers in the memory. The following dedicated registers are provided:
Program counter (PC):
A 16-bit register for indicating the instruction storage positions
Accumulator (A):
A 16-bit temporary register for storing arithmetic operations, etc. When the
instruction is an 8-bit data processing instruction, the lower byte is used.
Temporary accumulator (T):
A 16-bit register which performs arithmetic operations with the accumulator
When the instruction is an 8-bit data processing instruction, the lower byte is used.
Index register (IX):
A 16-bit register for index modification
Extra pointer (EP):
A 16-bit pointer for indicating a memory address
Stack pointer (SP):
A 16-bit register for indicating a stack area
Program status (PS):
A 16-bit register for storing a register pointer, a condition code
Initial value
16 bits
: Program counter
PC
FFFDH
A
: Accumulator
Indeterminate
T
: Temporary accumulator
Indeterminate
IX
: Index register
Indeterminate
EP
: Extra pointer
Indeterminate
SP
: Stack pointer
Indeterminate
PS
: Program status
I-flag = 0, IL1, IL0 = 11
The other bit values are indeterminate.
The PS can further be divided into higher 8 bits for use as a register bank pointer (RP) and the lower 8 bits for
use as a condition code register (CCR). (See the diagram below.)
• Structure of the Program Status Register
15
PS
14
13
12
RP
11
10
9
8
Vacancy Vacancy Vacancy
RP
7
6
5
4
3
2
1
0
H
I
IL1, IL0
N
Z
V
C
CCR
23
MB89670R/670AR Series
The RP indicates the address of the register bank currently in use. The relationship between the pointer contents
and the actual address is based on the conversion rule illustrated below.
• Rule for Conversion of Actual Addresses of the General-purpose Register Area
RP
Lower OP codes
“0” “0” “0” “0” “0” “0” “0” “1” R4 R3 R2 R1 R0 b2
↓
↓
↓
↓
↓
↓
↓
↓
↓
↓
↓
↓
↓
↓
b1
b0
↓
↓
Generated addresses A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
The CCR consists of bits indicating the results of arithmetic operations and the contents of transfer data and
bits for control of CPU operations at the time of an interrupt.
H-flag: Set to ‘1’ when a carry or a borrow from bit 3 to bit 4 occurs as a result of an arithmetic operation. Cleared
to ‘0’ otherwise. This flag is for decimal adjustment instructions.
I-flag:
Interrupt is enabled when this flag is set to ‘1’. Interrupt is disabled when the flag is cleared to ‘0’. Cleared
to ‘0’ at the reset.
IL1, IL0: Indicates the level of the interrupt currently allowed. Processes an interrupt only if its request level is
higher than the value indicated by this bit.
IL1
IL0
Interrupt level
0
0
0
1
1
0
2
1
1
3
1
High-low
High
Low
N-flag: Set to ‘1’ if the MSB becomes ‘1’ as the result of an arithmetic operation. Cleared to ‘0’ when the bit
is cleared to ‘0’.
Z-flag:
Set to ‘1’ when an arithmetic operation results in 0. Cleared to ‘0’ otherwise.
V-flag:
Set to ‘1’ if the complement on 2 overflows as a result of an arithmetic operation. Cleared to ‘0’ if the
overflow does not occur.
C-flag: Set to ‘1’ when a carry or a borrow from bit 7 occurs as a result of an arithmetic operation. Cleared
to ‘0’ otherwise. Set to the shift-out value in the case of a shift instruction.
24
MB89670R/670AR Series
The following general-purpose registers are provided:
General-purpose registers: An 8-bit register for storing data
The general-purpose registers are of 8 bits each and allocated in the register banks of the memory. One bank
contains eight registers and up to 32 banks can be used on every product of the MB89670R/670AR series. The
bank currently in use is indicated by the register bank pointer (RP).
• Register Bank Configuration
This address = 0100H + 8 × (RP)
R0
R1
R2
R3
R4
R5
R6
R7
32 banks
Memory area
25
MB89670R/670AR Series
■ I/O MAP
Address
Read/Write
Register abbreviation
00H
(R/W)
PDR0
Port 0 data register
01H
(W)
DDR0
Port 0 data direction register
02H
(R/W)
PDR1
Port 1 data register
03H
(W)
DDR1
Port 1 data direction register
04H
(R/W)
PDR2
Port 2 data register
05H
(W)
BCTR
External bus pin control register
06H
Register name
(Vacancy)
07H
(R/W)
SYCC
System clock control register
08H
(R/W)
STBC
Standby control register
09H
(R/W)
WDTC
Watchdog timer control register
0AH
(R/W)
TBTC
Timebase timer control register
0BH
(Vacancy)
0CH
(R/W)
PDR3
Port 3 data register
0DH
(W)
DDR3
Port 3 data direction register
0EH
(R/W)
PDR4
Port 4 data register
0FH
(W)
DDR4
Port 4 data direction register
10H
(R/W)
PDR5
Port 5 data register
11H
(R)
PDR6
Port 6 data register
12H
(R/W)
PPCR
Port 6 pull-up control register
13H
(R/W)
PDR7
Port 7 data register
14H
(R/W)
PDR8
Port 8 data/port 7 swiching register
15H
(R/W)
BZCR
Buzzer register
16H
(R/W)
CNTR #3
PWM control register #3
17H
(R/W)
COMP #3
PWM compare register #3
18H
(R/W)
TMCR
16-bit timer control register
19H
(R/W)
TCHR
16-bit timer count register (H)
1AH
(R/W)
TCLR
16-bit timer count register (L)
1BH
(Vacancy)
1CH
(R/W)
SMR
Serial mode register
1DH
(R/W)
SDR
Serial data register
1EH to 1FH
(Vacancy)
(Continued)
26
MB89670R/670AR Series
Address
Read/Write
Register abbreviation
20H
(R/W)
ADC1
A/D converter control register 1
21H
(R/W)
ADC2
A/D converter control register 2
22H
(R/W)
ADCH
A/D converter data register H
23H
(R/W)
ADCL
A/D converter data register L
24H
(R/W)
T2CR
Timer 2 control register
25H
(R/W)
T1CR
Timer 1 control register
26H
(R/W)
T2DR
Timer 2 data register
27H
(R/W)
T1DR
Timer 1 data register
28H
(R/W)
CNTR1
PWM 1 control register
29H
(R/W)
CNTR2
PWM 2 control register
2AH
(R/W)
CNTR3
PWM 3 control register
2BH
(W)
COMR2
PWM 2 compare register
2CH
(W)
COMR1
PWM 1 compare register
2DH to 2FH
Register name
(Vacancy)
30H
(R)
(W)
UDCR1
RCR1
Up/down counter register 1
Reload compare register1
31H
(R)
(W)
UDCR2
RCR2
Up/down counter register 2
Reload compare register2
32H
(R/W)
CCRA1
Counter control register A1
33H
(R/W)
CCRA2
Counter control register A2
34H
(R/W)
CCRB1
Counter control register B1
35H
(R/W)
CCRB2
Counter control register B2
36H
(R/W)
CSR1
Counter status register 1
37H
(R/W)
CSR2
Counter status register 2
38H
(R/W)
EIC1
External interrupt 1 control register 1
39H
(R/W)
EIC2
External interrupt 1 control register 2
3AH
(R/W)
EIE2
External interrupt 2 control register
3BH
(R/W)
EIF2
External interrupt 2 flag register
3CH to 3FH
(Vacancy)
(Continued)
27
MB89670R/670AR Series
(Continued)
Address
Read/Write
Register abbreviation
40H
(R/W)
USMR
UART serial mode register
41H
(R/W)
USCR
UART serial rate control register
42H
(R/W)
USTR
UART status register
43H
(R)
(W)
RXDR
TXDR
UART receiving data register
UART transmitting data register
44H
45H
(Vacancy)
(R/W)
RRDR
46H to 47H
Baud rate generator reload data register
(Vacancy)
48H*
(R/W)
CNTR #4
PWM control register #4
49H*
(R/W)
COMP #4
PWM compare register #4
4AH*
(R/W)
CNTR #5
PWM control register #5
4BH*
(R/W)
COMP #5
PWM compare register #5
4CH*
(R/W)
CNTR #6
PWM control register #6
4DH*
(R/W)
COMP #6
PWM compare register #6
4E to 7BH
(Vacancy)
7CH
(W)
ILR1
Interrupt level setting register 1
7DH
(W)
ILR2
Interrupt level setting register 2
7EH
(W)
ILR3
Interrupt level setting register 3
7FH
* : For the MB89673R/675R, these are (vacancies).
Note: Do not use (vacancies).
28
Register name
(Vacancy)
MB89670R/670AR Series
■ ELECTRICAL CHARACTERISTICS
1. Absolute Maximum Ratings
(AVSS = VSS = 0.0 V)
Parameter
Symbol
Rated value
Unit
Remarks
Min.
Max.
VCC
VSS – 0.3
VSS + 7.0
V
*
AVCC
VSS – 0.3
VCC + 0.3
V
*
A/D converter reference input
voltage
AVR
VSS – 0.3
VCC + 0.3
V
AVR must not exceed
“AVCC + 0.3 V”.
Input voltage
VI
VSS – 0.3
VCC + 0.3
V
VO1
VSS – 0.3
VCC + 0.3
V
Except P80 to P85
VO2
VSS – 0.3
VSS + 7.0
V
P80 to P85
IOL
—
20
mA
IOLAV1
—
4
mA
Average value (operating current
× operating rate)
IOLAV2
—
8
mA
Average value (operating current
× operating rate)
P80 to P85
“L” level total maximum output
current
∑IOL
—
100
mA
“L” level total average output
current
∑IOLAV
—
40
mA
“H” level maximum output
current
IOH
—
–20
mA
“H” level average output current
IOHAV
—
–4
mA
“H” level total maximum output
current
∑IOH
—
–50
mA
“H” level total average output
current
∑IOHAV
—
–20
mA
Power consumption
PD
—
300
mW
Operating temperature
TA
–40
+85
°C
Storage temperature
Tstg
–55
+150
°C
Power supply voltage
Output voltage
“L” level maximum output
current
“L” level average output current
Average value (operating current
× operating rate)
Average value (operating current
× operating rate)
Average value (operating current
× operating rate)
* : Use AVCC and VCC set at the same voltage.
Take care that AVR does not exceed “AVCC + 0.3 V” and AVCC does not exceed VCC, such as when power is turned
on.
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
29
MB89670R/670AR Series
2. Recommended Operating Conditions
(AVSS = VSS = 0.0 V)
Rated value
Symbol
Parameter
VCC
AVCC
Power supply voltage
Unit
Remarks
6.0
V
Normal operation assurance range
MB89673R/673AR/675R/675AR/677AR
2.7*
6.0
V
Normal operation assurance range
MB89PV670A/P677A
1.5
6.0
V
Retains the RAM state in the stop mode
Min.
Max.
2.2*
A/D converter reference input
voltage
AVR
0.0
AVCC
V
Operating temperature
TA
–40
+85
°C
* : These values vary with the operating frequency, and analog assurance range. See Figure 1 and “5. A/D Converter
Electrical Characteristics.”
Figure 1 Operating Voltage vs. Clock Operating Frequency
6
5
A/D converter accuracy assured in the
VCC = AVCC = 3.5 V to 6.0 V range.
Operating voltage (V)
Operation assurance range
4
3
2
1
Clock operating frequency (MHz)
1.0
2.0
4.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
Minimum execution time (µs)
0.8
0.4
Note: The shaded area is additional operating assurance range only for the MB89673R/673AR/675R/675AR/677AR.
30
MB89670R/670AR Series
The horizontal line of the graph in the figure 1 indicates the operating frequency of the external oscillator and
the lower horizontal line indicates the min. instruction execution time = 4/FC.
In the case of changing the operating clock with the clock gear function, be sure to convert it into the min.
instruction execution time on the lower horizontal line since the operating voltage range is dependent on the
min. instruction execution time.
WARNING: Recommended operating conditions are normal operating ranges for the semiconductor device. All
the device’s electrical characteristics are warranted when operated within these ranges.
Always use semiconductor devices within the recommended operating conditions. Operation outside
these ranges may adversely affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented on
the data sheet. Users considering application outside the listed conditions are advised to contact their
FUJITSU representative beforehand.
31
MB89670R/670AR Series
3. DC Characteristics
(AVCC = VCC = 5.0 V ±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Parameter
Pin name
Symbol
Condition
Rated value
Min.
Typ.
Max.
0.7 VCC

VCC + 0.3
P32 to P37,
P44, and P47
are of a port
input type.
V
P32 to P37,
P44, and P47
are of a
peripheral
input type.
V
P32 to P37,
P44, and P47
are of a port
input type.
0.2 VCC
V
P32 to P37,
P44, and P47
are of a
peripheral
input type.

VSS + 6.0
V
4.0


V
IOL = 4.0 mA


0.4
V
P80 to P85
IOL = 10 mA


0.5
V
VOL3
RST
IOL = 4.0 mA
—
—
0.4
V
ILI1
P00 to P07, P10 to P17,
P20 to P27, P30 to P37,
P40 to P47, P50 to P57,
P60 to P67, P70 to P76,
MOD0, MOD1
0.0 V < VI < VCC
—
—
±5
µA
ILI2
P80 to P85
0.0 V < VI < VCC
—
—
±1
µA
RPULL
P00 to P07, P10 to P17,
P30 to P37, P40 to P47,
P60 to P67, P70 to P76,
RST
VI = 0.0 V
25
50
100
kΩ
P00 to P07, P10 to P17,
P30 to P37, P40 to P47
VIHS
RST, MOD0, MOD1,
P32 to P37, P44, P47,
P60 to P67, P70 to P76
VIL
P00 to P07, P10 to P17,
P30 to P37, P40 to P47
VILS
RST, MOD0, MOD1,
P32 to P37, P44, P47,
P60 to P67, P70 to P76
VSS − 0.3

Open-drain output
VD
pin applied voltage
P80 to P85
VSS − 0.3
“H” level output
voltage
VOH
P00 to P07, P10 to P17,
P20 to P27, P30 to P37,
P40 to P47, P71, P72,
P74, P75
IOH = –2.0 mA
VOL1
P00 to P07, P10 to P17,
P20 to P27, P30 to P37,
P40 to P47, P50 to P57,
P70 to P76
VOL2
“H” level input
voltage
“L” level input
voltage
Input leakage
current
(Hi-z output
leakage current)
Pull-up
resistance
Remarks
V
VIH
“L” level output
voltage
Unit
0.8 VCC
—
VSS − 0.3


VCC + 0.3
0.3 VCC
Without
pull-up
resistor
option
With pull-up
resistor
option
(Continued)
32
MB89670R/670AR Series
(Continued)
Parameter
(AVCC = VCC = 5.0 V ±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Pin name
Symbol
Condition
FC = 10 MHz
VCC = 5.0 V
tinst*2 = 0.4 µs
ICC1
Sleep mode
VCC
ICCS1
Power supply
current*1
ICCS2
Min.
Typ.
Max.
—
12
20
Unit
mA
—
1
2
mA
—
1.5
2.5
mA
MB89P677A
FC = 10 MHz
VCC = 5.0 V
tinst*2 = 0.4 µs
—
3
7
mA
FC = 10 MHz
VCC = 3.0 V
tinst*2 = 6.4 µs
—
1
1.5
mA
ICCH
VCC = 3.0 V
TA = +25°C
Stop mode
—
—
1
mA
IA
FC = 10 MHz
When A/D
converter starts
—
6
8
mA
FC = 10 MHz
TA = +25°C
When A/D
converter is at a
stop
—
—
1
µA
f = 1 MHz
—
10
—
pF
AVCC
IAH
Input capacitance CIN
Other than AVCC,
AVSS, VCC, and VSS
Remarks
MB89673R/
673AR/
675R/675AR/
677AR/
PV670A
FC = 10 MHz
VCC = 3.0 V
tinst*2 = 6.4 µs
ICC2
Rated value
*1: The measurement conditions of the power supply current are as follows.
The external clock is used.
The output pins are open.
VCC is upon the condition above the table.
*2: For information on tinst, see “(4) Instruction Cycle” in “4. AC Characteristics.”
Note: The current consumption of connected EPROM and ICE is not considered on MB89PV670A.
33
MB89670R/670AR Series
4. AC Characteristics
(1) Reset Timing
(AVCC = VCC = 5.0 V ±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Symbol
Parameter
RST “L” pulse width
Condition
tZLZH
—
Rated value
Min.
Max.
48 tHCYL
—
Unit
Remarks
ns
tZLZH
0.8 VCC
RST
0.2 VCC
0.2 VCC
(2) Specifications for Power-on Reset
(AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Parameter
Symbol
Power supply rising time
tR
Power supply cut-off time
tOFF
Condition
—
Rated value
Unit
Remarks
Min.
Max.
—
50
ms
Power-on reset function only
1
—
ms
Min. internal time to next
power-on reset
Note: Make sure that power supply rises within the selected oscillation stabilization time.
If power supply voltage needs to be varied in the course of operation, a smooth voltage rise is
recommended.
tR
tOFF
2.0 V
VCC
34
0.2 V
0.2 V
0.2 V
MB89670R/670AR Series
(3) Clock Timing
(AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Pin
name
Symbol
Parameter
Rated value
Condition
Min.
Max.
Unit
Remarks
Clock frequency
FC
X0, X1
1
10
MHz
Clock cycle time
tXCYL
X0, X1
100
1000
ns
Input clock pulse width
PWH
PWL
X0
20
—
ns
External clock
Input clock rising/falling
time
tCR
tCF
X0
—
10
ns
External clock
—
• Clock Timing Conditions
tXCYL
PWH
PWL
tCF
tCR
0.8 VCC
0.8 VCC
X0
0.2 VCC
0.2 VCC
0.2 VCC
• Clock Configurations
When a crystal
or
ceramic resonator is used
X0
When an external clock is used
X1
X0
FC
C1
X1
Open
C2
(4) Instruction Cycle
(AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Parameter
Symbol
Instruction cycle
tinst
(minimum execution time)
Rated value (typical)
Unit
4/FC, 8/FC, 16/FC, 64/FC
µs
Remarks
(4/FC) tinst = 0.4 µs when operating at
FC = 10 MHz
35
MB89670R/670AR Series
(5) Clock Output Timing
(AVCC = VCC = 5.0 V ±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Parameter
Symbol
Pin name
Cycle time
tCYC
CLK
CLK ↑ → CLK ↓
tCHCL
CLK
Condition
—
Rated value
Max.
1/2 tinst*
—
µs
1/4 tinst – 0.07
1/4 tinst
µs
* : For information on tinst, see “(4) Instruction Cycle.”
tCYC
tCHCL
2.4 V
2.4 V
CLK
0.8 V
36
Unit
Min.
Remarks
MB89670R/670AR Series
(6) Bus Read Timing
(AVCC = VCC = 5.0 V ±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Parameter
Symbol
Pin name
Rated value
Condition
Min.
Max.
Unit Remarks
Valid address → RD
↓ time
tAVRL
RD, A15 to A08,
AD7 to AD0
1/4 tinst* – 0.06
—
µs
RD pulse width
tRLRH
RD
1/2 tinst *– 0.02
—
µs
Valid address → Data
read time
tAVDV
AD7 to AD0,
A15 to A08
—
1/2 tinst *
µs
No wait
RD ↓ → Data read time tRLDV
RD, AD7 to AD0
—
1/2 tinst *– 0.08
µs
No wait
RD ↑ → Data hold time
tRHDX
AD7 to AD0, RD
0
—
ns
RD ↑ → ALE ↑ time
tRHLH
RD, ALE
1/4 tinst* – 0.04
—
µs
RD ↑ → Address loss
time
tRHAX
RD, A15 to A08
1/4 tinst* – 0.04
—
µs
RD ↓ → CLK ↑ time
tRLCH
RD, CLK
1/4 tinst* – 0.04
—
µs
CLK ↓ → RD ↑ time
tCLRH
RD, CLK
0
—
ns
RD ↓ → BUFC ↓ time
tRLBL
RD, BUFC
–5
—
ns
BUFC ↑ → Valid
address time
tBHAV
A15 to A08,
AD7 to AD0,
BUFC
5
—
ns
—
* : For information on tinst, see “(4) Instruction Cycle.”
2.4 V
CLK
0.8 V
tRHLH
ALE
0.8 V
AD
2.4 V
0.7 VCC
0.7 VCC
2.4 V
0.8 V
0.3 VCC
0.3 VCC
0.8 V
tAVDV
tRHDX
2.4 V
A
2.4 V
tCLRH
0.8 V
tRLCH
0.8 V
tAVRL
tRLDV
2.4 V
0.8 V
tRHAX
tRLRH
2.4 V
RD
0.8 V
tRLBL
tBHAV
2.4 V
BUFC
0.8 V
37
MB89670R/670AR Series
(7) Bus Write Timing
(AVCC = VCC = 5.0 V ±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Parameter
Symbol
Pin name
Rated value
Condition
Min.
Max.
Valid address → ALE
↓ time
tAVLL
AD7 to AD0,
ALE, A15 to A08
1/4 tinst* 2 – 0.064
—
µs
ALE ↓ time →
Address loss time
tLLAX
AD7 to AD0,
ALE, A15 to A08
5*1
—
ns
Valid address → WR ↓ time
tAVWL
WR, ALE
1/4 tinst* 2 – 0.06
—
µs
WR pulse width
tWLWH
WR
1/2 tinst* 2 – 0.02
—
µs
Writing data → WR ↑ time
tDVWL
AD7 to AD0, WR
1/2 tinst* 2 – 0.06
—
µs
WR ↑ → Address loss
time
tWHAX
WR, A15 to A08
1/4 tinst* 2 – 0.04
—
µs
—
WR ↑ → Data hold time tWHDX
AD7 to AD0, WR
1/4 tinst* 2 – 0.04
—
µs
WR ↑ → ALE ↑ time
tWHLH
WR, ALE
1/4 tinst* – 0.04
—
µs
WR ↓ → CLK ↑ time
tWLCH
WR, CLK
—
µs
CLK ↓ → WR ↑ time
tCLWH
WR, CLK
0
—
ns
ALE pulse width
tLHLL
ALE
1/4 tinst* 2 – 0.035
—
µs
ALE ↓ → CLK ↑ time
tLLCH
ALE, CLK
1/4 tinst* 2 – 0.03
—
µs
inst* 2
1/4 t
– 0.04
*1: These characteristics are also applicable to the bus read timing.
*2: For information on tinst, see “(4) Instruction Cycle.”
2.4 V
CLK
0.8 V
tLHLL
tLLCH
tWHLH
2.4 V
ALE
0.8 V
tAVLL
0.8 V
tLLAX
2.4 V 2.4 V
2.4 V
0.8 V 0.8 V
0.8 V
2.4 V
AD
tDVWH
2.4 V
0.8 V
tWHDX
2.4 V
tCLWH
tWLCH
A
0.8 V
0.8 V
tAVWL
tWHAX
tWLWH
2.4 V
WR
0.8 V
38
Unit Remarks
MB89670R/670AR Series
(8) Ready Input Timing
(AVCC = VCC = 5.0 V ±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Parameter
Symbol
RDY valid → CLK
↑ time
tYVCH
CLK ↑ → RDY loss
time
tCHYX
Pin name
Rated value
Condition
Unit
Remarks
Min.
Max.
60
—
ns
*
0
—
ns
*
RDY, CLK
—
RDY, CLK
* : These characteristics are also applicable to the read cycle.
2.4 V
CLK
2.4 V
ALE
AD
Address
Data
A
WR
tYVCH tCHYX
2.4 V
2.4 V
RDY
0.8 V
0.8 V
tYVCH tCHYX
Note: The bus cycle is also extended in the read cycle in the same manner.
39
MB89670R/670AR Series
(9) Serial I/O Timing
(AVCC = 5.0 V ±10%, AVSS = VSS= 0.0 V, TA = –40°C to +85°C)
Parameter
Symbol
Pin name
Serial clock cycle time
tSCYC
SCK
SCK ↓ → SO time
tSLOV
SCK, SO
Valid SI → SCK ↑
tIVSH
SI, SCK
SCK ↑ → valid SI hold time
tSHIX
SCK, SI
Serial clock “H” pulse width
tSHSL
SCK
Serial clock “L” pulse width
tSLSH
SCK
Rated value
Condition
Internal shift
clock mode
Max.
2 tinst*
—
µs
–200
200
ns
1/2 tinst*
—
µs
1/2 tinst*
—
µs
1 tinst*
—
µs
1 tinst*
—
µs
0
200
ns
External shift
clock mode
SCK ↓ → SO time
tSLOV
SCK, SO
Valid SI → SCK ↑
tIVSH
SI, SCK
1/2 tinst*
—
µs
SCK ↑ → valid SI hold time
tSHIX
SCK, SI
1/2 tinst*
—
µs
* : For information on tinst, see “(4) Instruction Cycle.”
• Internal Shift Clock Mode
tSCYC
SCK
2.4 V
0.8 V
0.8 V
tSLOV
2.4 V
SO
0.8 V
tIVSH
tSHIX
0.8 VCC
0.8 VCC
0.2 VCC
0.2 VCC
SI
• External Shift Clock Mode
tSLSH
tSHSL
SCK
0.8 VCC
0.2 VCC
0.8 VCC
0.2 VCC
tSLOV
2.4 V
SO
0.8 V
tIVSH
tSHIX
0.8 VCC
0.8 VCC
0.2 VCC
0.2 VCC
SI
40
Unit
Min.
Remarks
MB89670R/670AR Series
(10) Peripheral Input Timing
(AVCC = 5.0 V ±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Symbol
Parameter
Pin name
Condition
Rated value
Min.
Max.
Unit
Peripheral input “H” pulse width 1
tILIH1
TCI
1 tinst*
—
µs
Peripheral input “L” pulse width 1
tIHIL1
TCI
1 tinst*
—
µs
Peripheral input “H” pulse width 2
tILIH2
EC,
INT0 to INT7
2 tinst*
—
µs
Peripheral input “L” pulse width 2
tIHIL2
EC,
INT0 to INT7
2 tinst*
—
µs
Peripheral input “H” pulse width 3
tILIH3
ADST
64 tinst*
—
µs
Peripheral input “L” pulse width 3
tIHIL3
ADST
A/D
mode
64 tinst*
—
µs
Peripheral input “H” pulse width 3
tILIH3
ADST
64 tinst*
—
µs
Peripheral input “L” pulse width 3
tIHIL3
ADST
Sense
mode
64 tinst*
—
µs
—
Remarks
* : For information on tinst, see “(4) Instruction Cycle.”
tIHIL1
tILIH1
0.8 VCC
TCI
0.2 VCC
0.2 VCC
tIHIL2
EC
INT0 to INT7
0.8 VCC
tILIH2
0.8 VCC
0.2 VCC
0.2 VCC
tIHIL3
tILIH3
0.8 VCC
ADST
0.2 VCC
0.8 VCC
0.8 VCC
0.2 VCC
41
MB89670R/670AR Series
(11) Up/down Counter Input Timing
(AVCC = VCC = 5.0 V ±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Parameter
Symbol
Pin name
Rated value
Min.
Max.
Unit
AIN input “1” pulse width
tAHL
2 tinst*
—
µs
AIN input “0” pulse width
tALL
2 tinst*
—
µs
BIN input “1” pulse width
tBHL
2 tinst*
—
µs
BIN input “0” pulse width
tBLL
2 tinst*
—
µs
AIN ↑ → BIN ↑ time
tAUBU
1 tinst*
—
µs
BIN ↑ → AIN ↓ time
tBUAD
1 tinst*
—
µs
AIN ↓ → BIN ↓ time
tADBD
1 tinst*
—
µs
BIN ↓ → AIN ↑ time
tBDAU
1 tinst*
—
µs
BIN ↑ → AIN ↑ time
tBUAU
1 tinst*
—
µs
AIN ↑ → BIN ↓ time
tAUBD
1 tinst*
—
µs
BIN ↓ → AIN ↓ time
tBDAD
1 tinst*
—
µs
AIN ↓ → BIN ↑ time
tADBU
1 tinst*
—
µs
ZIN input “1” pulse width
tZHL
1 tinst*
—
µs
ZIN input “0” pulse width
tZLL
1 tinst*
—
µs
P33, P34,
P36, P37
—
P32, P35
* : For information on tinst, see “(4) Instruction Cycle.”
42
Condition
Remarks
MB89670R/670AR Series
tAHL
AIN
tALL
0.8 VCC
0.8 VCC
0.2 VCC
tAUBU
tBUAD
0.2 VCC
tADBD
0.8 VCC
tBDAU
0.8 VCC
BIN
0.2 VCC
tBHL
0.2 VCC
tBLL
tBHL
tBLL
0.8 VCC
0.8 VCC
0.8 VCC
BIN
0.2 VCC
tBUAU
tAUBD
tBDAD
0.8 VCC
0.2 VCC
tADBU
0.8 VCC
AIN
0.2 VCC
tAHL
0.8 VCC
0.2 VCC
tALL
0.8 VCC
tZHL
ZIN
tZLL
0.2 VCC
0.2 VCC
43
MB89670R/670AR Series
5. A/D Converter Electrical Characteristics
(AVCC = VCC = 3.5 V to 6.0 V, FC = 10 MHz, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Parameter
Symbol
Pin name
Resolution
Linearity error
—
Differential linearity
error
—
Total error
Rated value
Unit
Min.
Typ.
Max.
—
—
10
bit
—
—
±2.0
LSB
—
—
±1.5
LSB
—
—
±3.0
LSB
Remarks
AVCC =
AVR = VCC
Zero transition voltage
VOT
AN0 to
AN7
AVSS – 1.5 LSB
AVSS + 0.5 LSB
AVSS + 2.5 LSB
mV
Full-scale transition
voltage
VFST
AN0 to
AN7
AVR – 3.5 LSB
AVR – 1.5 LSB
AVR + 0.5 LSB
mV
—
—
4
LSB
—
—
13.2
µs
At 10 MHz
oscillation
—
—
7.2
µs
At 10 MHz
oscillation
AN0 to
AN7
—
—
10
µA
AN0 to
AN7
0
—
AVR
V
AVR
0
—
AVCC
V
AVR
—
200

µA
Interchannel disparity
A/D mode conversion
time
—
—
Sense mode
conversion time
Analog port input
current
IAIN
Analog input voltage
—
Reference voltage
Reference voltage
supply current
IR
AVR = 5.0 V
6. Notes on Using A/D Converter
• The smaller | AVR – AVSS |, the greater the error would become relatively.
• The output impedance of the external circuit for the analog input must satisfy the following conditions:
Output impedance of the external circuit < Approx. 10 kΩ If the output impedance of the external circuit is too
high, an analog voltage sampling time might be insufficient (sampling time = 6 µs at 10 MHz oscillation).
An analog input equivalent circuit is shown below.
• Analog Input Equivalent Circuit
Sample hold circuit
R ≤ 10 kΩ is
recommended.
C
Analog input pin
R
60 pF
3 kΩ
Comparator
Analog channel selector
If R > 10 kΩ, it is recommended
to connect an external capacitor
of approx. 0.1 µF.
44
closes for approx. 15 instruction cycles
after starting A/D conversion.
Microcontrollers internal circuit
MB89670R/670AR Series
Since the A/D converter contains a sample hold circuit, the level of the analog input pin might not stabilize within
the sampling period after starting A/D, resulting in inaccurate A/D conversion values, if the input impedance to the
analog pin is too high. Be sure to maintain an appropriate input impedance to the analog pin.
It is recommended to keep the input impedance to the analog pin from exceeding 10 kΩ. If it exceeds 10 kΩ, it is
recommended to connect a capacitor of approx. 0.1 µF to the analog input pin.
Except for the sampling period after starting A/D, the input leakage current of the analog input pin is less than 10 µA.
7. A/D Converter Glossary
• Resolution
Analog-change that are identifiable with the A/D converter.
• Linearity error
The deviation of the straight line connecting the zero transition point (“00 0000 0000” ↔ “00 0000 0001”) with
the full-scale transition point (“11 1111 1111” ↔ “11 1111 1110”) from actual conversion characteristics
• Differential linearity error
The deviation of the input voltage needed to change the output code by 1 LSB from the theoretical voltage
• Total error
The difference between theoretical and actual conversion values, caused by the zero transition error, full-scale
transition error, linearity error, quantization error, and noise.
Theoreticall I/O characteristics
Total error
VFST
3FF
3FF
3FE
3FE
3FD
1.5 LSB
Digital output
Digital output
3FD
004
003
Actual conversion
value
{1 LSB × N + 0.5 LSB}
004
VNT
003
VOT
002
Actual conversion
value
002
1 LSB
Theoretical value
001
001
0.5 LSB
AVSS
AVR
1 LSB =
VFST – VOT
1022
AVSS
AVR
Analog input
Analog input
(V)
Total error of digital output N =
VNT – {1 LSB × N + 0.5 LSB }
1 LSB
(Continued)
45
MB89670R/670AR Series
(Continued)
Zero transition error
Full-scale transition error
004
Theoretical value
Actual conversion
value
3FF
Actual conversion
value
Digital output
Digital output
003
002
Theoretical
value
3FE
VFST (Actual
measured value)
3FD
Actual conversion
value
Actual conversion
value
001
3FC
VOT (Actual measured value)
AVSS
3FF
AVR
Analog input
Analog input
Linearity error
Differential linearity error
Theoretical value
Actual conversion
value
N+1
3FE
{1 LSB × N + VOT}
Actual conversion
value
VNT
VFST (Actual
measured
value)
004
003
V(N + 1)T
N
N–1
Actual conversion
value
002
Digital output
Digital output
3FD
VNT
Actual conversion
value
Theoretical value
N–2
001
VOT (Actual measured value)
AVSS
AVR
Analog input
Linearity error of digital output N =
46
AVSS
AVR
Analog input
VNT – {1 LSB × N + VOT}
1 LSB
Differential linearity error of digital output N =
V(N+1)T – VNT
1 LSB
– 1
MB89670R/670AR Series
■ EXAMPLE CHARACTERISTICS
(1) “L” Level Output Voltage
VOL1 vs. IOL
VOL1 (V)
0.8
0.7
VCC = 2.5 V
0.6
0.5
VCC = 3.0 V
0.4
VCC = 4.0 V
VCC = 5.0 V
VCC = 6.0 V
0.3
0.2
0.1
0.7
VCC = 2.5 V
0.6
0.5
VCC = 3.0 V
0.4
VCC = 4.0 V
VCC = 5.0 V
VCC = 6.0 V
0.3
0.2
0.1
0
1
2
3
4
5
6
IOL (mA)
(2) “H” Level Output Voltage
VCC – VOH (V)
1.0
TA = +25°C
0.9
0
2
4
6
8
10
12
IOL (mA)
(3) “H” Level Input Voltage/“L” Level Input
Voltage (CMOS Input)
VCC – VOH vs. IOH
VCC = 2.5 V
0.8
VIN vs. VCC
VIN (V)
5.0
4.5
TA = +25°C
4.0
3.5
0.7
VCC = 3.0 V
0.6
0.5
VCC = 4.0 V
VCC = 5.0 V
VCC = 6.0 V
0.4
0.3
3.0
2.5
2.0
1.5
0.2
1.0
0.1
0.5
0.0
0.0
VOL2 vs. IOL
VOL2 (V)
0.8
0.0
–0.5
–1.0
–1.5
–2.0
–2.5
–3.0
IOH (mA)
0
1
2
3
4
5
6
7
VCC (V)
47
MB89670R/670AR Series
(4) “H” Level Input Voltage/“L” Level Input Voltage (Hysteresis Input)
VIN vs. VCC
VIN (V)
5.0
4.5
TA = +25°C
4.0
VIHS
3.5
3.0
2.5
2.0
VILS
1.5
1.0
0.5
0.0
0
1
2
3
4
5
6
7
VCC (V)
VIHS: Threshold when input voltage in hysteresis characteristics is set to “H” level
VILS: Threshold when input voltage in hysteresis characteristics is set to “L” level
(5) Power Supply Current (External Clock)
ICC (mA)
20
ICC vs. VCC
ICCS vs. VCC
ICCS (mA)
10
15
ICC1
8
6
10
ICCS1
4
2
5
ICCS2
0
ICC2
0
3
4
5
3
4
6
VCC (V)
(6) Pull-up Resistance
RPULL vs. VCC
RPULL (kΩ)
1000
TA = +25°C
500
100
50
10
1
48
2
3
4
5
6
VCC (V)
5
6
VCC (V)
MB89670R/670AR Series
■ INSTRUCTIONS (136 instructions)
Execution instructions can be divided into the following four groups:
•
•
•
•
Transfer
Arithmetic operation
Branch
Others
Table 1 lists symbols used for notation of instructions.
Table 1
Instruction Symbols
Symbol
Meaning
dir
Direct address (8 bits)
off
Offset (8 bits)
ext
Extended address (16 bits)
#vct
Vector table number (3 bits)
#d8
Immediate data (8 bits)
#d16
Immediate data (16 bits)
dir: b
Bit direct address (8/3 bits)
rel
Branch relative address (8 bits)
@
Register indirect (e.g.: @A, @IX, @EP)
A
Accumulator A (Whether its length is 8 or 16 bits is determined by the instruction in use.)
AH
Upper 8 bits of accumulator A (8 bits)
AL
Lower 8 bits of accumulator A (8 bits)
T
Temporary accumulator T (Whether its length is 8 or 16 bits is determined by the
instruction in use.)
TH
Upper 8 bits of temporary accumulator T (8 bits)
TL
Lower 8 bits of temporary accumulator T (8 bits)
IX
Index register IX (16 bits)
(Continued)
49
MB89670R/670AR Series
(Continued)
Symbol
Meaning
EP
Extra pointer EP (16 bits)
PC
Program counter PC (16 bits)
SP
Stack pointer SP (16 bits)
PS
Program status PS (16 bits)
dr
Accumulator A or index register IX (16 bits)
CCR
Condition code register CCR (8 bits)
RP
Register bank pointer RP (5 bits)
Ri
General-purpose register Ri (8 bits, i = 0 to 7)
×
indicates that the very × is the immediate data.
(Whether its length is 8 or 16 bits is determined by the instruction in use.)
(×)
indicates that the contents at address ‘×’ is the target of accessing.
(Whether its length is 8 or 16 bits is determined by the instruction in use.)
(( × ))
The contents addressed by the contents at address ‘×’ is the target of accessing.
(Whether its length is 8 or 16 bits is determined by the instruction in use.)
Columns indicate the following:
Mnemonic:
Assembler notation of an instruction
~:
The number of instructions. An instruction cycle consists of 2 machine cycles.
#:
The number of bytes
Operation:
Operation of an instruction
TL, TH, AH:
A changed contents of the TL, TH and AH when instruction is executed. Symbols in
the column indicate the following:
•
•
•
•
“–” indicates no change.
dH is the upper 8 bits of the data in the operation.
AL and AH must become the contents of AL and AH each prior to the instruction executed.
“00” becomes “00”.
N, Z, V, C:
An instruction of which the corresponding flag will change. If + is written in this column,
the relevant instruction will change its corresponding flag.
OP code:
Code of an instruction. If an instruction is more than one code, it is written according to
the following rule:
e.g.: 48 to 4F ← This indicates 48, 49, ... 4F.
50
MB89670R/670AR Series
Table 2
Transfer Instructions (48 instructions)
Mnemonic
~
#
Operation
TL
TH
AH
NZVC
OP code
MOV dir,A
MOV @IX +off,A
MOV ext,A
MOV @EP,A
MOV Ri,A
MOV A,#d8
MOV A,dir
MOV A,@IX +off
MOV A,ext
MOV A,@A
MOV A,@EP
MOV A,Ri
MOV dir,#d8
MOV @IX +off,#d8
MOV @EP,#d8
MOV Ri,#d8
MOVW dir,A
MOVW @IX +off,A
3
4
4
3
3
2
3
4
4
3
3
3
4
5
4
4
4
5
2
2
3
1
1
2
2
2
3
1
1
1
3
3
2
2
2
2
–
–
–
–
–
AL
AL
AL
AL
AL
AL
AL
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
––––
––––
––––
––––
––––
++––
++––
++––
++––
++––
++––
++––
––––
––––
––––
––––
––––
––––
45
46
61
47
48 to 4F
04
05
06
60
92
07
08 to 0F
85
86
87
88 to 8F
D5
D6
MOVW ext,A
MOVW @EP,A
MOVW EP,A
MOVW A,#d16
MOVW A,dir
MOVW A,@IX +off
5
4
2
3
4
5
3
1
1
3
2
2
–
–
–
AL
AL
AL
–
–
–
AH
AH
AH
–
–
–
dH
dH
dH
––––
––––
––––
++––
++––
++––
D4
D7
E3
E4
C5
C6
MOVW A,ext
MOVW A,@A
MOVW A,@EP
MOVW A,EP
MOVW EP,#d16
MOVW IX,A
MOVW A,IX
MOVW SP,A
MOVW A,SP
MOV @A,T
MOVW @A,T
MOVW IX,#d16
MOVW A,PS
MOVW PS,A
MOVW SP,#d16
SWAP
SETB dir: b
CLRB dir: b
XCH A,T
XCHW A,T
XCHW A,EP
XCHW A,IX
XCHW A,SP
MOVW A,PC
5
4
4
2
3
2
2
2
2
3
4
3
2
2
3
2
4
4
2
3
3
3
3
2
3
1
1
1
3
1
1
1
1
1
1
3
1
1
3
1
2
2
1
1
1
1
1
1
(dir) ← (A)
( (IX) +off ) ← (A)
(ext) ← (A)
( (EP) ) ← (A)
(Ri) ← (A)
(A) ← d8
(A) ← (dir)
(A) ← ( (IX) +off)
(A) ← (ext)
(A) ← ( (A) )
(A) ← ( (EP) )
(A) ← (Ri)
(dir) ← d8
( (IX) +off ) ← d8
( (EP) ) ← d8
(Ri) ← d8
(dir) ← (AH),(dir + 1) ← (AL)
( (IX) +off) ← (AH),
( (IX) +off + 1) ← (AL)
(ext) ← (AH), (ext + 1) ← (AL)
( (EP) ) ← (AH),( (EP) + 1) ← (AL)
(EP) ← (A)
(A) ← d16
(AH) ← (dir), (AL) ← (dir + 1)
(AH) ← ( (IX) +off),
(AL) ← ( (IX) +off + 1)
(AH) ← (ext), (AL) ← (ext + 1)
(AH) ← ( (A) ), (AL) ← ( (A) ) + 1)
(AH) ← ( (EP) ), (AL) ← ( (EP) + 1)
(A) ← (EP)
(EP) ← d16
(IX) ← (A)
(A) ← (IX)
(SP) ← (A)
(A) ← (SP)
( (A) ) ← (T)
( (A) ) ← (TH),( (A) + 1) ← (TL)
(IX) ← d16
(A) ← (PS)
(PS) ← (A)
(SP) ← d16
(AH) ↔ (AL)
(dir): b ← 1
(dir): b ← 0
(AL) ↔ (TL)
(A) ↔ (T)
(A) ↔ (EP)
(A) ↔ (IX)
(A) ↔ (SP)
(A) ← (PC)
AL
AL
AL
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
AL
AL
–
–
–
–
AH
AH
AH
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
AH
–
–
–
–
dH
dH
dH
dH
–
–
dH
–
dH
–
–
–
dH
–
–
AL
–
–
–
dH
dH
dH
dH
dH
++––
++––
++––
––––
––––
––––
––––
––––
––––
––––
––––
––––
––––
++++
––––
––––
––––
––––
––––
––––
––––
––––
––––
––––
C4
93
C7
F3
E7
E2
F2
E1
F1
82
83
E6
70
71
E5
10
A8 to AF
A0 to A7
42
43
F7
F6
F5
F0
Notes: • During byte transfer to A, the data transfered at “T ← A” is restricted to low bytes.
• Operands in more than one operand instruction must be stored in the order in which their mnemonics
are written. (Reverse arrangement of F2MC-8 family)
51
MB89670R/670AR Series
Table 3
Mnemonic
~
#
ADDC A,Ri
ADDC A,#d8
ADDC A,dir
ADDC A,@IX +off
ADDC A,@EP
ADDCW A
ADDC A
SUBC A,Ri
SUBC A,#d8
SUBC A,dir
SUBC A,@IX +off
SUBC A,@EP
SUBCW A
SUBC A
INC Ri
INCW EP
INCW IX
INCW A
DEC Ri
DECW EP
DECW IX
DECW A
MULU A
DIVU A
ANDW A
ORW A
XORW A
CMP A
CMPW A
RORC A
3
2
3
4
3
3
2
3
2
3
4
3
3
2
4
3
3
3
4
3
3
3
19
21
3
3
3
2
3
2
1
2
2
2
1
1
1
1
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ROLC A
2
1
CMP A,#d8
CMP A,dir
CMP A,@EP
CMP A,@IX +off
CMP A,Ri
DAA
DAS
XOR A
XOR A,#d8
XOR A,dir
XOR A,@EP
XOR A,@IX +off
XOR A,Ri
AND A
AND A,#d8
AND A,dir
2
3
3
4
3
2
2
2
2
3
3
4
3
2
2
3
2
2
1
2
1
1
1
1
2
2
1
2
1
1
2
2
Arithmetic Operation Instructions (62 instructions)
Operation
TL
TH
AH
NZVC
OP code
(A) ← (A) + (Ri) + C
(A) ← (A) + d8 + C
(A) ← (A) + (dir) + C
(A) ← (A) + ( (IX) +off) + C
(A) ← (A) + ( (EP) ) + C
(A) ← (A) + (T) + C
(AL) ← (AL) + (TL) + C
(A) ← (A) − (Ri) − C
(A) ← (A) − d8 − C
(A) ← (A) − (dir) − C
(A) ← (A) − ( (IX) +off) − C
(A) ← (A) − ( (EP) ) − C
(A) ← (T) − (A) − C
(AL) ← (TL) − (AL) − C
(Ri) ← (Ri) + 1
(EP) ← (EP) + 1
(IX) ← (IX) + 1
(A) ← (A) + 1
(Ri) ← (Ri) − 1
(EP) ← (EP) − 1
(IX) ← (IX) − 1
(A) ← (A) − 1
(A) ← (AL) × (TL)
(A) ← (T) / (AL),MOD → (T)
(A) ← (A) ∧ (T)
(A) ← (A) ∨ (T)
(A) ← (A) ∀ (T)
(TL) − (AL)
(T) − (A)
→ C→A
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
dL
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
00
–
–
–
–
–
–
–
–
–
–
–
dH
–
–
–
–
–
–
dH
–
–
–
–
dH
–
–
–
dH
dH
00
dH
dH
dH
–
–
–
++++
++++
++++
++++
++++
++++
++++
++++
++++
++++
++++
++++
++++
++++
+++–
––––
––––
++––
+++–
––––
––––
++––
––––
––––
++R–
++R–
++R–
++++
++++
++–+
28 to 2F
24
25
26
27
23
22
38 to 3F
34
35
36
37
33
32
C8 to CF
C3
C2
C0
D8 to DF
D3
D2
D0
01
11
63
73
53
12
13
03
C ← A←
–
–
–
++–+
02
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
++++
++++
++++
++++
++++
++++
++++
++R–
++R–
++R–
++R–
++R–
++R–
++R–
++R–
++R–
14
15
17
16
18 to 1F
84
94
52
54
55
57
56
58 to 5F
62
64
65
(A) − d8
(A) − (dir)
(A) − ( (EP) )
(A) − ( (IX) +off)
(A) − (Ri)
Decimal adjust for addition
Decimal adjust for subtraction
(A) ← (AL) ∀ (TL)
(A) ← (AL) ∀ d8
(A) ← (AL) ∀ (dir)
(A) ← (AL) ∀ ( (EP) )
(A) ← (AL) ∀ ( (IX) +off)
(A) ← (AL) ∀ (Ri)
(A) ← (AL) ∧ (TL)
(A) ← (AL) ∧ d8
(A) ← (AL) ∧ (dir)
(Continued)
52
MB89670R/670AR Series
(Continued)
Mnemonic
~
#
AND A,@EP
AND A,@IX +off
AND A,Ri
OR A
OR A,#d8
OR A,dir
OR A,@EP
OR A,@IX +off
OR A,Ri
CMP dir,#d8
CMP @EP,#d8
CMP @IX +off,#d8
CMP Ri,#d8
INCW SP
DECW SP
3
4
3
2
2
3
3
4
3
5
4
5
4
3
3
1
2
1
1
2
2
1
2
1
3
2
3
2
1
1
Operation
(A) ← (AL) ∧ ( (EP) )
(A) ← (AL) ∧ ( (IX) +off)
(A) ← (AL) ∧ (Ri)
(A) ← (AL) ∨ (TL)
(A) ← (AL) ∨ d8
(A) ← (AL) ∨ (dir)
(A) ← (AL) ∨ ( (EP) )
(A) ← (AL) ∨ ( (IX) +off)
(A) ← (AL) ∨ (Ri)
(dir) – d8
( (EP) ) – d8
( (IX) + off) – d8
(Ri) – d8
(SP) ← (SP) + 1
(SP) ← (SP) – 1
Table 4
Mnemonic
BZ/BEQ rel
BNZ/BNE rel
BC/BLO rel
BNC/BHS rel
BN rel
BP rel
BLT rel
BGE rel
BBC dir: b,rel
BBS dir: b,rel
JMP @A
JMP ext
CALLV #vct
CALL ext
XCHW A,PC
RET
RETI
~
#
3
3
3
3
3
3
3
3
5
5
2
3
6
6
3
4
6
2
2
2
2
2
2
2
2
3
3
1
3
1
3
1
1
1
Mnemonic
PUSHW A
POPW A
PUSHW IX
POPW IX
NOP
CLRC
SETC
CLRI
SETI
~
#
4
4
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
TH
AH
NZVC
OP code
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
++R–
++R–
++R–
++R–
++R–
++R–
++R–
++R–
++R–
++++
++++
++++
++++
––––
––––
67
66
68 to 6F
72
74
75
77
76
78 to 7F
95
97
96
98 to 9F
C1
D1
Branch Instructions (17 instructions)
Operation
If Z = 1 then PC ← PC + rel
If Z = 0 then PC ← PC + rel
If C = 1 then PC ← PC + rel
If C = 0 then PC ← PC + rel
If N = 1 then PC ← PC + rel
If N = 0 then PC ← PC + rel
If V ∀ N = 1 then PC ← PC + rel
If V ∀ N = 0 then PC ← PC + reI
If (dir: b) = 0 then PC ← PC + rel
If (dir: b) = 1 then PC ← PC + rel
(PC) ← (A)
(PC) ← ext
Vector call
Subroutine call
(PC) ← (A),(A) ← (PC) + 1
Return from subrountine
Return form interrupt
Table 5
TL
TL
TH
AH
NZVC
OP code
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
dH
–
–
––––
––––
––––
––––
––––
––––
––––
––––
–+––
–+––
––––
––––
––––
––––
––––
––––
Restore
FD
FC
F9
F8
FB
FA
FF
FE
B0 to B7
B8 to BF
E0
21
E8 to EF
31
F4
20
30
Other Instructions (9 instructions)
Operation
TL
TH
AH
NZVC
OP code
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
dH
–
–
–
–
–
–
–
––––
––––
––––
––––
––––
–––R
–––S
––––
––––
40
50
41
51
00
81
91
80
90
53
54
0
0
NOP
1
MULU
1
SWAP
DIVU
A
2
ROLC
A
CMP
A
2
3
RET
RETI
4
5
6
7
8
9
PUSHW POPW MOV
MOVW CLRI
A
A
A,ext
A,PS
SETI
CLRB
BBC
INCW
DECW JMP
MOVW
dir: 0 dir: 0,rel
A
A
@A
A,PC
SETC
CLRB
BBC
INCW
DECW MOVW MOVW
dir: 1 dir: 1,rel
SP
SP
SP,A
A,SP
JMP
CALL
PUSHW POPW MOV
MOVW CLRC
addr16 addr16
IX
IX
ext,A
PS,A
ADDC
A
SUBC
A
A
XCH
XOR
AND
OR
A, T
A
A
A
A
B
C
D
E
F
MOV
MOV
CLRB
BBC
INCW
DECW MOVW MOVW
@A,T
A,@A
dir: 2 dir: 2,rel
IX
IX
IX,A
A,IX
3
RORC CMPW ADDCW SUBCW XCHW XORW ANDW ORW
MOVW MOVW CLRB
BBC
INCW
DECW MOVW MOVW
A
A
A
A
A, T
A
A
A
@A,T
A,@A
dir: 3 dir: 3,rel
EP
EP
EP,A
A,EP
4
MOV
CMP
ADDC SUBC
A,#d8
A,#d8
A,#d8
A,#d8
5
MOV
CMP
ADDC SUBC MOV
XOR
AND
OR
MOV
CMP
CLRB
BBC
MOVW MOVW MOVW XCHW
A,dir
A,dir
A,dir
A,dir
dir,A
A,dir
A,dir
A,dir dir,#d8 dir,#d8
dir: 5 dir: 5,rel
A,dir
dir,A SP,#d16
A,SP
6
MOV
CMP
ADDC
SUBC
XOR
AND
OR
DAA
A,#d8
A,#d8
A,#d8
MOV
XOR
AND
OR
MOV
DAS
CMP
A,@IX +d A,@IX +d A,@IX +d A,@IX +d @IX +d,A A@,IX +d A,@IX +d A,@IX +d @IX +d,#d8 @IX +d,#d8
CLRB
BBC
MOVW MOVW MOVW XCHW
dir: 4 dir: 4,rel
A,ext
ext,A A,#d16
A,PC
CLRB
BBC
MOVW MOVW MOVW XCHW
dir: 6 dir: 6,rel A,@IX +d @IX +d,A IX,#d16
A,IX
7
MOV
CMP
ADDC SUBC MOV
XOR
AND
OR
MOV
CMP
CLRB
BBC
MOVW MOVW MOVW XCHW
A,@EP A,@EP A,@EP A,@EP @EP,A A,@EP A,@EP A,@EP @EP,#d8 @EP,#d8
dir: 7 dir: 7,rel A,@EP @EP,A EP,#d16
A,EP
8
MOV
CMP
ADDC SUBC MOV
XOR
AND
OR
MOV
CMP
SETB
BBS
INC
DEC
CALLV BNC
A,R0
A,R0
A,R0
A,R0
R0,A
A,R0
A,R0
A,R0 R0,#d8 R0,#d8
dir: 0 dir: 0,rel
R0
R0
#0
rel
9
MOV
CMP
ADDC SUBC MOV
XOR
AND
OR
MOV
CMP
SETB
BBS
INC
DEC
CALLV BC
A,R1
A,R1
A,R1
A,R1
R1,A
A,R1
A,R1
A,R1 R1,#d8 R1,#d8
dir: 1 dir: 1,rel
R1
R1
#1
rel
MOV
CMP
ADDC SUBC MOV
XOR
AND
OR
MOV
CMP
SETB
BBS
INC
DEC
CALLV BP
A,R2
A,R2
A,R2
A,R2
R2,A
A,R2
A,R2
A,R2 R2,#d8 R2,#d8
dir: 2 dir: 2,rel
R2
R2
#2
rel
MOV
CMP
ADDC SUBC MOV
XOR
AND
OR
MOV
CMP
SETB
BBS
INC
DEC
CALLV BN
A,R3
A,R3
A,R3
A,R3
R3,A
A,R3
A,R3
A,R3 R3,#d8 R3,#d8
dir: 3 dir: 3,rel
R3
R3
#3
rel
A
B
C
MOV
CMP
ADDC SUBC MOV
XOR
AND
OR
MOV
CMP
SETB
BBS
INC
DEC
CALLV BNZ
A,R4
A,R4
A,R4
A,R4
R4,A
A,R4
A,R4
A,R4 R4,#d8 R4,#d8
dir: 4 dir: 4,rel
R4
R4
#4
rel
D
MOV
CMP
ADDC SUBC MOV
XOR
AND
OR
MOV
CMP
SETB
BBS
INC
DEC
CALLV BZ
A,R5
A,R5
A,R5
A,R5
R5,A
A,R5
A,R5
A,R5 R5,#d8 R5,#d8
dir: 5 dir: 5,rel
R5
R5
#5
rel
E
MOV
CMP
ADDC SUBC MOV
XOR
AND
OR
MOV
CMP
SETB
BBS
INC
DEC
CALLV BGE
A,R6
A,R6
A,R6
A,R6
R6,A
A,R6
A,R6
A,R6 R6,#d8 R6,#d8
dir: 6 dir: 6,rel
R6
R6
#6
rel
F
MOV
CMP
ADDC SUBC MOV
XOR
AND
OR
MOV
CMP
SETB
BBS
INC
DEC
CALLV BLT
A,R7
A,R7
A,R7
A,R7
R7,A
A,R7
A,R7
A,R7 R7,#d8 R7,#d8
dir: 7 dir: 7,rel
R7
R7
#7
rel
MB89670R/670AR Series
H
H
■ INSTRUCTION MAP
LL
MB89670R/670AR Series
■ MASK OPTIONS
Part number
MB89673R
MB89673AR
MB89675R
MB89675AR
MB89677AR
MB89P677A
MB89PV670A
Specifying procedure
Specify when
ordering masking
Set with EPROM
programmer
Setting not possible
1
Pull-up resistors
P10 to P17,
P30 to P37, P40 to P47,
P70 to P76
Selectable by pin
Selectable by pin
2
Pull-up resistors
P00 to P03
Selectable by pin
Selectable in 4-pin
unit
3
Pull-up resistors
P04 to P07
Selectable by pin
Selectable in 4-pin
unit
4
Power-on reset
With power-on reset
Without power-on reset
Selectable
Selectable
Fixed to “with
power-on reset”
Selectable
Selectable
Fixed to Approx.
218/FC (Approx.
26.2 ms)
Selectable
Selectable
Fixed to “with reset
output”
No.
Oscillation stabilization time
selection (at 10 MHz)
5
Approx. 218/FC (approx. 26.2 ms)
Approx. 217/FC (approx. 13.1 ms)
Approx. 214/FC (approx. 1.6 ms)
Approx. 24/FC (approx. 0 ms)
Fixed to “without
pull-up resistor”
FC: Clock frequency
6
Reset pin output
With reset output
Without reset output
■ ORDERING INFORMATION
Part number
Package
MB89673RPF
MB89673ARPF
MB89675RPF
MB89675ARPF
MB89677ARPF
MB89P677APF
80-pin Plastic QFP
(FPT-80P-M06)
MB89673RPFM
MB89673ARPFM
MB89675RPFM
MB89675ARPFM
MB89677ARPFM
MB89P677APFM
80-pin Plastic LQFP
(FPT-80P-M11)
MB89PV670ACF
80-pin Ceramic MQFP
(MQP-80C-P01)
Remarks
55
MB89670R/670AR Series
■ PACKAGE DIMENSIONS
80-pin Plastic QFP
(FPT-80P-M06)
23.90±0.40(.941±.016)
64
20.00±0.20(.787±.008)
3.35(.132)MAX
(Mounting height)
0.05(.002)MIN
(STAND OFF)
41
65
40
14.00±0.20
(.551±.008)
12.00(.472)
REF
17.90±0.40
(.705±.016)
16.30±0.40
(.642±.016)
INDEX
80
25
"A"
LEAD No.
1
24
0.80(.0315)TYP
0.35±0.10
(.014±.004)
0.16(.006)
0.15±0.05(.006±.002)
M
Details of "A" part
Details of "B" part
0.25(.010)
"B"
0.10(.004)
18.40(.724)REF
22.30±0.40(.878±.016)
C
56
1994 FUJITSU LIMITED F80010S-3C-2
0.30(.012)
0.18(.007)MAX
0.58(.023)MAX
0 10°
0.80±0.20
(.031±.008)
Dimensions in mm (inches)
MB89670R/670AR Series
80-pin Plastic LQFP
(FPT-80P-M11)
+0.20
1.50 −0.10
+.008
.059 −.004
16.00±0.20(.630±.008)SQ
14.00±0.10(.551±.004)SQ
60
41
61
(Mounting height)
40
12.35
(.486)
REF
15.00
(.591)
NOM
1 PIN INDEX
80
LEAD No.
21
1
0.65(.0256)TYP
0.30±0.10
(.012±.004)
20
0.13(.005)
0.10(.004)
C
1995 FUJITSU LIMITED F80016S-1C-3
Details of "A" part
"A"
M
0.10±0.10
(STAND OFF)
(.004±.004)
+0.05
0.127 −0.02
+.002
.005 −.001
0
10˚
0.50±0.20
(.020±.008)
Dimensions in mm (inches)
57
MB89670R/670AR Series
80-pin Ceramic MQFP
(MQP-80C-P01)
18.70(.736)TYP
12.00(.472)TYP
INDEX AREA
16.30±0.33
(.642±.013)
15.58±0.20
(.613±.008)
1.50(.059)TYP
1.00(.040)TYP
4.50(.177)
TYP
1.27±0.13
(.050±.005)
22.30±0.33
(.878±.013)
24.70(.972)
TYP
0.30(.012)
TYP
0.80±0.25
(.0315±.010)
0.80±0.25
(.0315±.010)
+0.40
1.20 –0.20
+.016
.047 –.008
INDEX AREA
18.12±0.20
12.02(.473)
(.713±.008)
TYP
10.16(.400)
14.22(.560)
TYP
TYP
18.40(.724)
REF
INDEX
1.27±0.13
(.050±.005)
6.00(.236)
TYP
0.30(.012)TYP
7.62(.300)TYP
9.48(.373)TYP
11.68(.460)TYP
0.40±0.10
(.016±.004)
1.50(.059)
TYP
1.00(.040)
TYP
0.40±0.10
(.016±.004)
+0.40
1.20 –0.20
+.016
.047 –.008
0.15±0.05 8.70(.343)
(.006±.002) MAX
C
58
1994 FUJITSU LIMITED M80001SC-4-2
Dimensions
Dimensions in
in mm
mm (inches)
(inches)
MB89670R/670AR Series
FUJITSU LIMITED
For further information please contact:
Japan
FUJITSU LIMITED
Corporate Global Business Support Division
Electronic Devices
KAWASAKI PLANT, 4-1-1, Kamikodanaka
Nakahara-ku, Kawasaki-shi
Kanagawa 211-8588, Japan
Tel: (044) 754-3763
Fax: (044) 754-3329
http://www.fujitsu.co.jp/
North and South America
FUJITSU MICROELECTRONICS, INC.
Semiconductor Division
3545 North First Street
San Jose, CA 95134-1804, USA
Tel: (408) 922-9000
Fax: (408) 922-9179
Customer Response Center
Mon. - Fri.: 7 am - 5 pm (PST)
Tel: (800) 866-8608
Fax: (408) 922-9179
http://www.fujitsumicro.com/
Europe
FUJITSU MIKROELEKTRONIK GmbH
Am Siebenstein 6-10
D-63303 Dreieich-Buchschlag
Germany
Tel: (06103) 690-0
Fax: (06103) 690-122
http://www.fujitsu-ede.com/
Asia Pacific
FUJITSU MICROELECTRONICS ASIA PTE LTD
#05-08, 151 Lorong Chuan
New Tech Park
Singapore 556741
Tel: (65) 281-0770
Fax: (65) 281-0220
All Rights Reserved.
The contents of this document are subject to change without
notice. Customers are advised to consult with FUJITSU sales
representatives before ordering.
The information and circuit diagrams in this document presented
as examples of semiconductor device applications, and are not
intended to be incorporated in devices for actual use. Also,
FUJITSU is unable to assume responsibility for infringement of
any patent rights or other rights of third parties arising from the
use of this information or circuit diagrams.
FUJITSU semiconductor devices are intended for use in
standard applications (computers, office automation and other
office equipment, industrial, communications, and measurement
equipment, personal or household devices, etc.).
CAUTION:
Customers considering the use of our products in special
applications where failure or abnormal operation may directly
affect human lives or cause physical injury or property damage,
or where extremely high levels of reliability are demanded (such
as aerospace systems, atomic energy controls, sea floor
repeaters, vehicle operating controls, medical devices for life
support, etc.) are requested to consult with FUJITSU sales
representatives before such use. The company will not be
responsible for damages arising from such use without prior
approval.
Any semiconductor devices have inherently a certain rate of
failure. You must protect against injury, damage or loss from
such failures by incorporating safety design measures into your
facility and equipment such as redundancy, fire protection, and
prevention of over-current levels and other abnormal operating
conditions.
If any products described in this document represent goods or
technologies subject to certain restrictions on export under the
Foreign Exchange and Foreign Trade Control Law of Japan, the
prior authorization by Japanese government should be required
for export of those products from Japan.
http://www.fmap.com.sg/
F9803
 FUJITSU LIMITED Printed in Japan
59
Similar pages