Elpida MC-4R128FKE6D-653 Direct rambus dram rimm module 128m-byte (64m-word x 16-bit) Datasheet

DATA SHEET
MOS INTEGRATED CIRCUIT
MC-4R128FKE6D
Direct Rambus DRAM RIMMTM Module
128M-BYTE (64M-WORD x 16-BIT)
Description
The Direct Rambus RIMM module is a general-purpose high-performance memory module subsystem suitable for
use in a broad range of applications including computer memory, personal computers, workstations, and other
applications where high bandwidth and low latency are required.
MC-4R128FKE6D modules consists of four 288M Direct Rambus DRAM (Direct RDRAM) devices (µPD488588).
These are extremely high-speed CMOS DRAMs organized as 16M words by 18 bits. The use of Rambus Signaling
Level (RSL) technology permits 600MHz, 711MHz or 800MHz transfer rates while using conventional system and
board design technologies.
Direct RDRAM devices are capable of sustained data transfers at 1.25 ns per two bytes (10 ns per sixteen bytes).
The architecture of the Direct RDRAM enables the highest sustained bandwidth for multiple, simultaneous,
randomly addressed memory transactions. The separate control and data buses with independent row and column
control yield over 95 % bus efficiency. The Direct RDRAM's 32 banks support up to four simultaneous transactions
per device.
Features
• 184 edge connector pads with 1mm pad spacing
• 128 MB Direct RDRAM storage
• Each RDRAM has 32 banks, for 128 banks total on module
• Gold plated contacts
• RDRAMs use Chip Scale Package (CSP)
• Serial Presence Detect support
• Operates from a 2.5 V supply
• Powerdown self refresh modes
• Separate Row and Column buses for higher efficiency
• Over Drive Factor (ODF) support
The information in this document is subject to change without notice. Before using this document, please
confirm that this is the latest version.
Not all devices/types available in every country. Please check with local Elpida Memory, Inc. for
availability and additional information.
Document No. E0093N20 (Ver. 2.0)
Date Published June 2002 (K) Japan
URL: http://www.elpida.com
Elpida Memory,Inc. 2001-2002
Elpida Memory, Inc. is a joint venture DRAM company of NEC Corporation and Hitachi, Ltd.
MC-4R128FKE6D
Order information
Part number
I/O Freq.
RAS access time
MHz
ns
800
45
184 edge connector pads RIMM 4 pieces of
MC-4R128FKE6D - 745
711
45
with heat spreader
µPD488588FF
MC-4R128FKE6D - 653
600
53
Edge connector : Gold plated
FBGA (µBGA) package
MC-4R128FKE6D - 845
2
Organization
64M x 16
Package
Data Sheet E0093N20 (Ver. 2.0)
Mounted devices
MC-4R128FKE6D
Module Pad Configuration
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
B31
B32
B33
B34
B35
B36
B37
B38
B39
B40
B41
B42
B43
B44
B45
B46
GND
LDQA7
GND
LDQA5
GND
LDQA3
GND
LDQA1
GND
LCFM
GND
LCFMN
GND
NC
GND
LROW2
GND
LROW0
GND
LCOL3
GND
LCOL1
GND
LDQB0
GND
LDQB2
GND
LDQB4
GND
LDQB6
GND
LDQB8
GND
LCMD
VCMOS
SIN
VCMOS
NC
GND
NC
VDD
VDD
NC
NC
NC
NC
GND
LDQA8
GND
LDQA6
GND
LDQA4
GND
LDQA2
GND
LDQA0
GND
LCTMN
GND
LCTM
GND
NC
GND
LROW1
GND
LCOL4
GND
LCOL2
GND
LCOL0
GND
LDQB1
GND
LDQB3
GND
LDQB5
GND
LDQB7
GND
LSCK
VCMOS
SOUT
VCMOS
NC
GND
NC
VDD
VDD
NC
NC
NC
NC
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
A33
A34
A35
A36
A37
A38
A39
A40
A41
A42
A43
A44
A45
A46
LCFM, LCFMN,
Side B
Side A
RCFM, RCFMN : Clock from master
LCTM, LCTMN,
RCTM, RCTMN : Clock to master
B47
B48
B49
B50
B51
B52
B53
B54
B55
B56
B57
B58
B59
B60
B61
B62
B63
B64
B65
B66
B67
B68
B69
B70
B71
B72
B73
B74
B75
B76
B77
B78
B79
B80
B81
B82
B83
B84
B85
B86
B87
B88
B89
B90
B91
B92
NC
NC
NC
NC
VREF
GND
SA0
VDD
SA1
SVDD
SA2
VDD
RCMD
GND
RDQB8
GND
RDQB6
GND
RDQB4
GND
RDQB2
GND
RDQB0
GND
RCOL1
GND
RCOL3
GND
RROW0
GND
RROW2
GND
NC
GND
RCFMN
GND
RCFM
GND
RDQA1
GND
RDQA3
GND
RDQA5
GND
RDQA7
GND
NC
NC
NC
NC
VREF
GND
SCL
VDD
SDA
SVDD
SWP
VDD
RSCK
GND
RDQB7
GND
RDQB5
GND
RDQB3
GND
RDQB1
GND
RCOL0
GND
RCOL2
GND
RCOL4
GND
RROW1
GND
NC
GND
RCTM
GND
RCTMN
GND
RDQA0
GND
RDQA2
GND
RDQA4
GND
RDQA6
GND
RDQA8
GND
A47
A48
A49
A50
A51
A52
A53
A54
A55
A56
A57
A58
A59
A60
A61
A62
A63
A64
A65
A66
A67
A68
A69
A70
A71
A72
A73
A74
A75
A76
A77
A78
A79
A80
A81
A82
A83
A84
A85
A86
A87
A88
A89
A90
A91
A92
LCMD, RCMD
: Serial Command Pad
LROW2 - LROW0,
RROW2 - RROW0 : Row bus
LCOL4 - LCOL0,
RCOL4 - RCOL0
: Column bus
LDQA8 - LDQA0,
RDQA8 - RDQA0
: Data bus A
LDQB8 - LDQB0,
RDQB8 - RDQB0
: Data bus B
LSCK, RSCK : Clock input
SA0 - SA2
: Serial Presence Detect Address
SCL, SDA
: Serial Presence Detect Clock
SIN, SOUT
: Serial I/O
SVDD
: SPD Voltage
SWP
: Serial Presence Detect Write Protect
VCMOS
: Supply voltage for serial pads
VDD
: Supply voltage
VREF
: Logic threshold
GND
: Ground reference
NC
: These pads are not connected
Data Sheet E0093N20 (Ver. 2.0)
3
MC-4R128FKE6D
Module Pad Names
Pad
4
Signal Name
Pad
Signal Name
Pad
Signal Name
Pad
Signal Name
A1
GND
A2
LDQA8
B1
GND
A47
NC
B47
NC
B2
LDQA7
A48
NC
B48
A3
NC
GND
B3
GND
A49
NC
B49
NC
A4
LDQA6
B4
LDQA5
A50
NC
B50
NC
A5
GND
B5
GND
A51
VREF
B51
VREF
A6
LDQA4
B6
LDQA3
A52
GND
B52
GND
A7
GND
B7
GND
A53
SCL
B53
SA0
A8
LDQA2
B8
LDQA1
A54
VDD
B54
VDD
A9
GND
B9
GND
A55
SDA
B55
SA1
A10
LDQA0
B10
LCFM
A56
SVDD
B56
SVDD
A11
GND
B11
GND
A57
SWP
B57
SA2
A12
LCTMN
B12
LCFMN
A58
VDD
B58
VDD
A13
GND
B13
GND
A59
RSCK
B59
RCMD
A14
LCTM
B14
NC
A60
GND
B60
GND
A15
GND
B15
GND
A61
RDQB7
B61
RDQB8
A16
NC
B16
LROW2
A62
GND
B62
GND
A17
GND
B17
GND
A63
RDQB5
B63
RDQB6
A18
LROW1
B18
LROW0
A64
GND
B64
GND
A19
GND
B19
GND
A65
RDQB3
B65
RDQB4
A20
LCOL4
B20
LCOL3
A66
GND
B66
GND
RDQB2
A21
GND
B21
GND
A67
RDQB1
B67
A22
LCOL2
B22
LCOL1
A68
GND
B68
GND
A23
GND
B23
GND
A69
RCOL0
B69
RDQB0
A24
LCOL0
B24
LDQB0
A70
GND
B70
GND
A25
GND
B25
GND
A71
RCOL2
B71
RCOL1
A26
LDQB1
B26
LDQB2
A72
GND
B72
GND
A27
GND
B27
GND
A73
RCOL4
B73
RCOL3
A28
LDQB3
B28
LDQB4
A74
GND
B74
GND
A29
GND
B29
GND
A75
RROW1
B75
RROW0
A30
LDQB5
B30
LDQB6
A76
GND
B76
GND
A31
GND
B31
GND
A77
NC
B77
RROW2
A32
LDQB7
B32
LDQB8
A78
GND
B78
GND
A33
GND
B33
GND
A79
RCTM
B79
NC
A34
LSCK
B34
LCMD
A80
GND
B80
GND
A35
VCMOS
B35
VCMOS
A81
RCTMN
B81
RCFMN
A36
SOUT
B36
SIN
A82
GND
B82
GND
A37
VCMOS
B37
VCMOS
A83
RDQA0
B83
RCFM
A38
NC
B38
NC
A84
GND
B84
GND
A39
GND
B39
GND
A85
RDQA2
B85
RDQA1
A40
NC
B40
NC
A86
GND
B86
GND
A41
VDD
B41
VDD
A87
RDQA4
B87
RDQA3
A42
VDD
B42
VDD
A88
GND
B88
GND
A43
NC
B43
NC
A89
RDQA6
B89
RDQA5
A44
NC
B44
NC
A90
GND
B90
GND
A45
NC
B45
NC
A91
RDQA8
B91
RDQA7
A46
NC
B46
NC
A92
GND
B92
GND
Data Sheet E0093N20 (Ver. 2.0)
MC-4R128FKE6D
Module Connector Pad Description
Signal
(1/2)
I/O
Type
Description
GND
–
–
Ground reference for RDRAM core and interface. 72 PCB connector pads.
LCFM
I
RSL
Clock from master. Interface clock used for receiving RSL signals from the
Channel. Positive polarity.
LCFMN
I
RSL
LCMD
I
VCMOS
Clock from master. Interface clock used for receiving RSL signals from the
Channel. Negative polarity.
Serial Command used to read from and write to the control registers. Also used
for power management.
LCOL4..LCOL0
I
RSL
Column bus. 5-bit bus containing control and address information for column
accesses.
LCTM
I
RSL
Clock to master. Interface clock used for transmitting RSL signals to the
Channel. Positive polarity.
LCTMN
I
RSL
Clock to master. Interface clock used for transmitting RSL signals to the
Channel. Negative polarity.
LDQA8..LDQA0
I/O
RSL
Data bus A. A 9-bit bus carrying a byte of read or write data between the Channel
LDQB8..LDQB0
I/O
RSL
Data bus B. A 9-bit bus carrying a byte of read or write data between the Channel
and the RDRAM. LDQA8 is non-functional on modules with x16 RDRAM devices.
and the RDRAM. LDQB8 is non-functional on modules with x16 RDRAM devices.
LROW2..LROW0
I
RSL
LSCK
I
VCMOS
Row bus. 3-bit bus containing control and address information for row accesses.
Serial clock input. Clock source used to read from and write to the RDRAM
control registers.
NC
–
–
These pads are not connected. These 24 connector pads are reserved for future
use.
RCFM
I
RSL
RCFMN
I
RSL
RCMD
I
VCMOS
Clock from master. Interface clock used for receiving RSL signals from the
Channel. Positive polarity.
Clock from master. Interface clock used for receiving RSL signals from the
Channel. Negative polarity.
Serial Command Input used to read from and write to the control registers. Also
used for power management.
RCOL4..RCOL0
I
RSL
Column bus. 5-bit bus containing control and address information for column
accesses.
RCTM
I
RSL
RCTMN
I
RSL
Clock to master. Interface clock used for transmitting RSL signals to the
Channel. Positive polarity.
Clock to master. Interface clock used for transmitting RSL signals to the
Channel. Negative polarity.
RDQA8..RDQA0
I/O
RSL
Data bus A. A 9-bit bus carrying a byte of read or write data between the Channel
RDQB8..RDQB0
I/O
RSL
Data bus B. A 9-bit bus carrying a byte of read or write data between the Channel
I
RSL
and the RDRAM. RDQA8 is non-functional on modules with x16 RDRAM devices.
and the RDRAM. RDQB8 is non-functional on modules with x16 RDRAM devices.
RROW2..RROW0
Row bus. 3-bit bus containing control and address information for row accesses.
Data Sheet E0093N20 (Ver. 2.0)
5
MC-4R128FKE6D
(2/2)
Signal
RSCK
I/O
Type
I
VCMOS
Description
Serial clock input. Clock source used to read from and write to the RDRAM
control registers.
SA0
I
SVDD
Serial Presence Detect Address 0.
SA1
I
SVDD
Serial Presence Detect Address 1.
SA2
I
SVDD
Serial Presence Detect Address 2.
SCL
I
SVDD
Serial Presence Detect Clock.
SDA
I/O
SVDD
Serial Presence Detect Data (Open Collector I/O).
SIN
I/O
VCMOS
Serial I/O for reading from and writing to the control registers. Attaches to SIO0
SOUT
I/O
VCMOS
of the first RDRAM on the module.
Serial I/O for reading from and writing to the control registers. Attaches to SIO1
of the last RDRAM on the module.
SVDD
—
—
SWP
I
SVDD
SPD Voltage. Used for signals SCL, SDA, SWP, SA0, SA1 and SA2.
Serial Presence Detect Write Protect (active high). When low, the SPD can be
written as well as read.
VCMOS
—
—
CMOS I/O Voltage. Used for signals CMD, SCK, SIN, SOUT.
VDD
—
—
Supply voltage for the RDRAM core and interface logic.
VREF
—
—
Logic threshold reference voltage for RSL signals.
6
Data Sheet E0093N20 (Ver. 2.0)
MC-4R128FKE6D
Block Diagram
DQA 8
DQA 7
DQA 6
DQA 5
DQA 4
DQA 3
DQA 2
DQA 1
DQA 0
CFM
CFMN
CTM
CTMN
ROW 2
ROW 1
ROW 0
COL 4
COL 3
COL 2
COL 1
COL 0
DQB 0
DQB 1
DQB 2
DQB 3
DQB 4
DQB 5
DQB 6
DQB 7
DQB 8
U1
SIO 1
DQA 8
DQA 7
DQA 6
DQA 5
DQA 4
DQA 3
DQA 2
DQA 1
DQA 0
CFM
CFMN
CTM
CTMN
ROW 2
ROW 1
ROW 0
COL 4
COL 3
COL 2
COL 1
COL 0
DQB 0
DQB 1
DQB 2
DQB 3
DQB 4
DQB 5
DQB 6
DQB 7
DQB 8
U2
SCK
DQA 8
DQA 7
DQA 6
DQA 5
DQA 4
DQA 3
DQA 2
DQA 1
DQA 0
CFM
CFMN
CTM
CTMN
ROW 2
ROW 1
ROW 0
COL 4
COL 3
COL 2
COL 1
COL 0
DQB 0
DQB 1
DQB 2
DQB 3
DQB 4
DQB 5
DQB 6
DQB 7
DQB 8
DQA 8
DQA 7
DQA 6
DQA 5
DQA 4
DQA 3
DQA 2
DQA 1
DQA 0
CFM
CFMN
CTM
CTMN
ROW 2
ROW 1
ROW 0
COL 4
COL 3
COL 2
COL 1
COL 0
DQB 0
DQB 1
DQB 2
DQB 3
DQB 4
DQB 5
DQB 6
DQB 7
DQB 8
U4
SIO 1
RDQA 8
RDQA 7
RDQA 6
RDQA 5
RDQA 4
RDQA 3
RDQA 2
RDQA 1
RDQA 0
RCFM
RCFMN
RCTM
RCTMN
RROW 2
RROW 1
RROW 0
RCOL 4
RCOL 3
RCOL 2
RCOL 1
RCOL 0
RDQB 0
RDQB 1
RDQB 2
RDQB 3
RDQB 4
RDQB 5
RDQB 6
RDQB 7
RDQB 8
SOUT
RSCK
RCMD
A0
A2
WP
A1
7
Data Sheet E0093N20 (Ver. 2.0)
SDA
SWP
SDA
SCL
U0
SCL
VDD
VCMOS
LDQA 8
LDQA 7
LDQA 6
LDQA 5
LDQA 4
LDQA 3
LDQA 2
LDQA 1
LDQA 0
LCFM
LCFMN
LCTM
LCTMN
LROW 2
LROW 1
LROW 0
LCOL 4
LCOL 3
LCOL 2
LCOL 1
LCOL 0
LDQB 0
LDQB 1
LDQB 2
LDQB 3
LDQB 4
LDQB 5
LDQB 6
LDQB 7
LDQB 8
SIN
LSCK
LCMD
VREF
SIO 0
SCK
CMD
VREF
SIO 0
SIO 1
CMD
VREF
SIO 0
SIO 1
SCK
U3
CMD
VREF
SIO 0
SCK
CMD
VREF
SVDD
VCC
47 kΩ
SA0 SA1 SA2
SERIAL PD
Remarks 1. Rambus Channel signals form a loop through the RIMM module, with the exception of the SIO chain.
2. See Serial Presence Detection Specification for information on the SPD device and its contents.
MC-4R128FKE6D
Electrical Specification
Absolute Maximum Ratings
Symbol
Parameter
MIN.
MAX.
Unit
VI,ABS
Voltage applied to any RSL or CMOS signal pad with respect to GND
−0.3
VDD + 0.3
V
VDD,ABS
Voltage on VDD with respect to GND
−0.5
VDD + 1.0
V
TSTORE
Storage temperature
−50
+100
°C
Caution
Exposing the device to stress above those listed in Absolute Maximum Ratings could cause
permanent damage. The device is not meant to be operated under conditions outside the limits
described in the operational section of this specification. Exposure to Absolute Maximum Rating
conditions for extended periods may affect device reliability.
DC Recommended Electrical Conditions
Symbol
Parameter and conditions
VDD
Supply voltage
VCMOS
CMOS I/O power supply at pad
MIN.
MAX.
Unit
2.50 − 0.13
2.50 + 0.13
V
2.5V controllers
2.5 − 0.13
2.5 + 0.25
V
1.8V controllers
1.8 − 0.1
1.8 + 0.2
VREF
Reference voltage
1.4 − 0.2
1.4 + 0.2
V
VIL
RSL input low voltage
VREF − 0.5
VREF − 0.2
V
VIH
RSL input high voltage
VREF + 0.2
VREF + 0.5
V
VIL,CMOS
CMOS input low voltage
−0.3
0.5VCMOS − 0.25
V
VIH,CMOS
CMOS input high voltage
0.5VCMOS+0.25
VCMOS + 0.3
V
VOL,CMOS
CMOS output low voltage, IOL,CMOS = 1 mA
—
0.3
V
VOH,CMOS
CMOS output high voltage, IOH,CMOS = −0.25 mA
VCMOS − 0.3
—
V
IREF
VREF current, VREF,MAX
−40.0
+40.0
µA
ISCK,CMD
CMOS input leakage current, (0 ≤ VCMOS ≤ VDD)
−40.0
+40.0
µA
ISIN,SOUT
CMOS input leakage current, (0 ≤ VCMOS ≤ VDD)
−10.0
+10.0
µA
8
Data Sheet E0093N20 (Ver. 2.0)
MC-4R128FKE6D
AC Electrical Specifications
Symbol
Z
Parameter and Conditions
MIN.
TYP.
MAX.
Unit
Module Impedance of RSL signals
25.2
28.0
30.8
Ω
Module Impedance of SCK and CMD signals
23.8
28.0
32.2
Average clock delay from finger to finger of all RSL clock nets
TPD
1.28
ns
(CTM, CTMN,CFM, and CFMN)
∆TPD
∆TPD-CMOS
Propagation delay variation of RSL signals with respect to TPD Note1,2
−21
+21
ps
Propagation delay variation of SCK signal with respect to an average clock
−250
+250
ps
−200
+200
ps
-845
12.0
%
-745
12.0
-653
10.5
Forward crosstalk coefficient
-845
2.0
(300ps input rise time 20% - 80%)
-745
2.0
-653
2.0
Backward crosstalk coefficient
-845
1.5
(300ps input rise time 20% - 80%)
-745
1.5
-653
1.5
-845
0.6
-745
0.6
-653
0.6
delay Note1
∆TPD- SCK,CMD Propagation delay variation of CMD signal with respect to SCK signal
Attenuation Limit
Vα/VIN
VXF/VIN
VXB/VIN
RDC
DC Resistance Limit
%
%
Ω
Notes 1. TPD or Average clock delay is defined as the average delay from finger to finger of all RSL clock nets (CTM,
CTMN, CFM, and CFMN).
2. If the RIMM module meets the following specification, then it is compliant to the specification.
If the RIMM module does not meet these specifications, then the specification can be adjusted by the
“Adjusted ∆TPD Specification” table.
Adjusted ∆TPD Specification
Symbol
∆TPD
Parameter and conditions
Propagation delay variation of RSL signals with respect to TPD
Adjusted MIN./MAX.
+/− [17+(18*N*∆Z0)] Note
Absolute
MIN.
MAX.
−30
+30
Unit
ps
Note N = Number of RDRAM devices installed on the RIMM module.
∆Z0 = delta Z0% = (MAX. Z0 − MIN. Z0) / (MIN. Z0)
(MAX. Z0 and MIN. Z0 are obtained from the loaded (high impedance) impedance coupons of all RSL layers
on the module.)
Data Sheet E0093N20 (Ver. 2.0)
9
MC-4R128FKE6D
RIMM Module Current Profile
IDD
IDD1
IDD2
IDD3
IDD4
IDD5
IDD6
RIMM module power conditions Note1
One RDRAM in Read
Note2
, balance in NAP mode
One RDRAM in Read Note2, balance in Standby mode
One RDRAM in Read
Note2
, balance in Active mode
One RDRAM in Write, balance in NAP mode
One RDRAM in Write, balance in Standby mode
One RDRAM in Write, balance in Active mode
MAX.
Unit
-845
642.6
mA
-745
592.6
-653
532.6
-845
900
-745
820
-653
730
-845
1035
-745
955
-653
865
-845
732.6
-745
682.6
-653
632.6
-845
990
-745
910
-653
830
-845
1125
-745
1045
-653
965
mA
mA
mA
mA
mA
Notes 1. Actual power will depend on individual RDRAM component specifications, memory controller and usage
patterns. Power does not include Refresh Current.
2. I/O current is a function of the % of 1’s, to add I/O power for 50 % 1’s for a x16 need to add 257 mA or 290
mA for x18 ECC module for the following : VDD = 2.5 V, VTERM = 1.8 V, VREF = 1.4 V and VDIL = VREF − 0.5 V.
10
Data Sheet E0093N20 (Ver. 2.0)
MC-4R128FKE6D
Package Drawings
184 EDGE CONNECTOR PADS RIMM (SOCKET TYPE) (1/2)
EEPROM
A (AREA B)
R
P
O N
288 M Direct RDRAM
M1 (AREA B)
S
A
M
Q
L
M2 (AREA A)
K
H
G
B
I
D
B
T
J
E
F
C
A1 (AREA A)
detail of B part
detail of A part
W
C1
R1.00
R1.00
Y
B1
X
Z
ITEM
A
MILLIMETERS
133.35 TYP.
A1
133.35±0.13
B
55.175
B1
1.00±0.10
C
11.50
C1
3.00±0.10
D
45.00
E
F
32.00
G
5.675
H
47.625
I
25.40
J
47.625
K
6.35
L
1.00 TYP.
M
34.925±0.13
M1
15.145
M2
19.78
N
29.21
O
17.78
P
4.00±0.10
Q
R 2.00
R
3.00±0.10
φ 2.44
1.27±0.10
0.80±0.05
2.99
0.30
2.00±0.10
S
T
W
X
Y
Z
45.00
ECA-TS2-0012-02
Data Sheet E0093N20 (Ver. 2.0)
11
MC-4R128FKE6D
184 EDGE CONNECTOR PADS RIMM (SOCKET TYPE) (2/2)
A
B
E
C
Pad A1
C
Pad A92
G
H
D
DESCRIPTION
PCB length
MIN.
133.22
TYP.
133.35
MAX.
133.48
UNIT
mm
B
PCB height
34.795
34.925
35.055
mm
C
Center-center pad width from pad A1 to A46,
A47 to A92, B1 to B46 or B47 to B92
Spacing from PCB left edge to connector key notch
44.95
45.00
45.05
mm
-
55.175
-
mm
-
17.78
-
mm
1.17
1.27
1.37
mm
-
-
3.09
mm
-
-
4.46
mm
ITEM
A
D
E
F
G
H
Spacing from contact pad PCB edge
to side edge retainer notch
PCB thickness
Heat spreader thickness from PCB surface (one side) to
heat spreader top surface
RIMM thickness
ECA-TS2-0012-02
12
Data Sheet E0093N20 (Ver. 2.0)
F
MC-4R128FKE6D
CAUTION FOR HANDLING MEMORY MODULES
When handling or inserting memory modules, be sure not to touch any components on the modules, such as
the memory ICs, chip capacitors and chip resistors. It is necessary to avoid undue mechanical stress on
these components to prevent damaging them.
In particular, do not push module cover or drop the modules in order to protect from mechanical defects,
which would be electrical defects.
When re-packing memory modules, be sure the modules are not touching each other.
Modules in contact with other modules may cause excessive mechanical stress, which may damage the
modules.
MDE0202
NOTES FOR CMOS DEVICES
1
PRECAUTION AGAINST ESD FOR MOS DEVICES
Exposing the MOS devices to a strong electric field can cause destruction of the gate
oxide and ultimately degrade the MOS devices operation. Steps must be taken to stop
generation of static electricity as much as possible, and quickly dissipate it, when once
it has occurred. Environmental control must be adequate. When it is dry, humidifier
should be used. It is recommended to avoid using insulators that easily build static
electricity. MOS devices must be stored and transported in an anti-static container,
static shielding bag or conductive material. All test and measurement tools including
work bench and floor should be grounded. The operator should be grounded using
wrist strap. MOS devices must not be touched with bare hands. Similar precautions
need to be taken for PW boards with semiconductor MOS devices on it.
2
HANDLING OF UNUSED INPUT PINS FOR CMOS DEVICES
No connection for CMOS devices input pins can be a cause of malfunction. If no
connection is provided to the input pins, it is possible that an internal input level may be
generated due to noise, etc., hence causing malfunction. CMOS devices behave
differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed
high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected
to VDD or GND with a resistor, if it is considered to have a possibility of being an output
pin. The unused pins must be handled in accordance with the related specifications.
3
STATUS BEFORE INITIALIZATION OF MOS DEVICES
Power-on does not necessarily define initial status of MOS devices. Production process
of MOS does not define the initial operation status of the device. Immediately after the
power source is turned ON, the MOS devices with reset function have not yet been
initialized. Hence, power-on does not guarantee output pin levels, I/O settings or
contents of registers. MOS devices are not initialized until the reset signal is received.
Reset operation must be executed immediately after power-on for MOS devices having
reset function.
CME0107
Data Sheet E0093N20 (Ver. 2.0)
13
MC-4R128FKE6D
Rambus, RDRAM and the Rambus logo are registered trademarks of Rambus Inc.
RIMM, SO-RIMM, RaSer and QRSL are trademarks of Rambus Inc.
µBGA is a registered trademark of Tessera, Inc
The information in this document is subject to change without notice. Before using this document, confirm that this is the latest version.
No part of this document may be copied or reproduced in any form or by any means without the prior
written consent of Elpida Memory, Inc.
Elpida Memory, Inc. does not assume any liability for infringement of any intellectual property rights
(including but not limited to patents, copyrights, and circuit layout licenses) of Elpida Memory, Inc. or
third parties by or arising from the use of the products or information listed in this document. No license,
express, implied or otherwise, is granted under any patents, copyrights or other intellectual property
rights of Elpida Memory, Inc. or others.
Descriptions of circuits, software and other related information in this document are provided for
illustrative purposes in semiconductor product operation and application examples. The incorporation of
these circuits, software and information in the design of the customer's equipment shall be done under
the full responsibility of the customer. Elpida Memory, Inc. assumes no responsibility for any losses
incurred by customers or third parties arising from the use of these circuits, software and information.
[Product applications]
Elpida Memory, Inc. makes every attempt to ensure that its products are of high quality and reliability.
However, users are instructed to contact Elpida Memory's sales office before using the product in
aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment,
medical equipment for life support, or other such application in which especially high quality and
reliability is demanded or where its failure or malfunction may directly threaten human life or cause risk
of bodily injury.
[Product usage]
Design your application so that the product is used within the ranges and conditions guaranteed by
Elpida Memory, Inc., including the maximum ratings, operating supply voltage range, heat radiation
characteristics, installation conditions and other related characteristics. Elpida Memory, Inc. bears no
responsibility for failure or damage when the product is used beyond the guaranteed ranges and
conditions. Even within the guaranteed ranges and conditions, consider normally foreseeable failure
rates or failure modes in semiconductor devices and employ systemic measures such as fail-safes, so
that the equipment incorporating Elpida Memory, Inc. products does not cause bodily injury, fire or other
consequential damage due to the operation of the Elpida Memory, Inc. product.
[Usage environment]
This product is not designed to be resistant to electromagnetic waves or radiation. This product must be
used in a non-condensing environment.
If you export the products or technology described in this document that are controlled by the Foreign
Exchange and Foreign Trade Law of Japan, you must follow the necessary procedures in accordance
with the relevant laws and regulations of Japan. Also, if you export products/technology controlled by
U.S. export control regulations, or another country's export control laws or regulations, you must follow
the necessary procedures in accordance with such laws or regulations.
If these products/technology are sold, leased, or transferred to a third party, or a third party is granted
license to use these products, that third party must be made aware that they are responsible for
compliance with the relevant laws and regulations.
M01E0107
Similar pages