ON MC14011B B-suffix series cmos gate Datasheet

MC14001B Series
B−Suffix Series CMOS Gates
MC14001B, MC14011B, MC14023B,
MC14025B, MC14071B, MC14073B,
MC14081B, MC14082B
http://onsemi.com
The B Series logic gates are constructed with P and N channel
enhancement mode devices in a single monolithic structure
(Complementary MOS). Their primary use is where low power
dissipation and/or high noise immunity is desired.
MARKING
DIAGRAMS
14
PDIP−14
P SUFFIX
CASE 646
Features
• Supply Voltage Range = 3.0 Vdc to 18 Vdc
• All Outputs Buffered
• Capable of Driving Two Low−power TTL Loads or One Low−power
•
•
•
MC140xxBCP
AWLYYWW
1
14
SOIC−14
D SUFFIX
CASE 751A
Schottky TTL Load Over the Rated Temperature Range.
Double Diode Protection on All Inputs Except: Triple Diode
Protection on MC14011B and MC14081B
Pin−for−Pin Replacements for Corresponding CD4000 Series
B Suffix Devices
Pb−Free Packages are Available*
140xxB
AWLYWW
1
14
TSSOP−14
DT SUFFIX
CASE 948G
14
0xxB
ALYW
MAXIMUM RATINGS (Voltages Referenced to VSS)
Symbol
Value
Unit
−0.5 to +18.0
V
−0.5 to VDD + 0.5
V
Input or Output Current
(DC or Transient) per Pin
± 10
mA
PD
Power Dissipation, per Package
(Note 1)
500
mW
TA
Ambient Temperature Range
−55 to +125
°C
Tstg
Storage Temperature Range
−65 to +150
°C
TL
Lead Temperature
(8−Second Soldering)
260
°C
VDD
Vin, Vout
Iin, Iout
Parameter
1
DC Supply Voltage Range
Input or Output Voltage Range
(DC or Transient)
xx
A
WL, L
YY, Y
WW, W
MC140xxB
AWLYWW
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
1
= Specific Device Code
= Assembly Location
= Wafer Lot
= Year
= Work Week
DEVICE INFORMATION
Device
This device contains protection circuitry to guard against damage due to high
static voltages or electric fields. However, precautions must be taken to avoid
applications of any voltage higher than maximum rated voltages to this
high−impedance circuit. For proper operation, Vin and Vout should be constrained
to the range VSS (Vin or Vout) VDD.
Unused inputs must always be tied to an appropriate logic voltage level
(e.g., either VSS or VDD). Unused outputs must be left open.
February, 2005 − Rev. 4
SOEIAJ−14
F SUFFIX
CASE 965
1
Maximum ratings are those values beyond which device damage can occur.
Maximum ratings applied to the device are individual stress limit values (not
normal operating conditions) and are not valid simultaneously. If these limits are
exceeded, device functional operation is not implied, damage may occur and
reliability may be affected.
1. Temperature Derating:
Plastic “P and D/DW” Packages: – 7.0 mW/C From 65C To 125C
 Semiconductor Components Industries, LLC, 2005
14
Description
MC14001B
Quad 2−Input NOR Gate
MC14011B
Quad 2−Input NAND Gate
MC14023B
Triple 3−Input NAND Gate
MC14025B
Triple 3−Input NOR Gate
MC14071B
Quad 2−Input OR Gate
MC14073B
Triple 3−Input AND Gate
MC14081B
Quad 2−Input AND Gate
MC14082B
Dual 4−Input AND Gate
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 8 of this data sheet.
Publication Order Number:
MC14001B/D
MC14001B Series
LOGIC DIAGRAMS
NAND
OR
AND
MC14001B
Quad 2−Input NOR Gate
MC14011B
Quad 2−Input NAND Gate
MC14071B
Quad 2−Input OR Gate
MC14081B
Quad 2−Input AND Gate
2 INPUT
NOR
1
2
3
1
2
3
1
2
3
1
2
3
5
6
4
5
6
4
5
6
4
5
6
4
8
9
10
8
9
10
8
9
10
8
9
10
12
13
11
12
13
11
12
13
11
12
13
11
3 INPUT
MC14025B
Triple 3−Input NOR Gate
1
2
8
3
4
5
11
12
13
9
6
10
MC14023B
Triple 3−Input NAND Gate
1
2
8
3
4
5
11
12
13
MC14073B
Triple 3−Input AND Gate
1
2
8
3
4
5
11
12
13
9
6
10
9
6
10
MC14082B
Dual 4−Input AND Gate
2
3
4
5
9
10
11
12
1
13
NC = 6, 8
VDD = PIN 14
VSS = PIN 7
FOR ALL DEVICES
PIN ASSIGNMENTS
MC14001B
Quad 2−Input NOR Gate
MC14023B
Triple 3−Input NAND Gate
MC14011B
Quad 2−Input NAND Gate
MC14025B
Triple 3−Input NOR Gate
IN 1A
1
14
VDD
IN 1A
1
14
VDD
IN 1A
1
14
VDD
IN 1A
1
14
VDD
IN 2A
2
13
IN 2D
IN 2A
2
13
IN 2D
IN 2A
2
13
IN 3C
IN 2A
2
13
IN 3C
OUTA
3
12
IN 1D
OUTA
3
12
IN 1D
IN 1B
3
12
IN 2C
IN 1B
3
12
IN 2C
OUTB
4
11
OUTD
OUTB
4
11
OUTD
IN 2B
4
11
IN 1C
IN 2B
4
11
IN 1C
IN 1B
5
10
OUTC
IN 1B
5
10
OUTC
IN 3B
5
10
OUTC
IN 3B
5
10
OUTC
IN 2B
6
9
IN 2C
IN 2B
6
9
IN 2C
OUTB
6
9
OUTA
OUTB
6
9
OUTA
VSS
7
8
IN 1C
VSS
7
8
IN 1C
VSS
7
8
IN 3A
VSS
7
8
IN 3A
MC14071B
Quad 2−Input OR Gate
MC14073B
Triple 3−Input AND Gate
MC14081B
Quad 2−Input AND Gate
MC14082B
Dual 4−Input AND Gate
IN 1A
1
14
VDD
IN 1A
1
14
VDD
IN 1A
1
14
VDD
OUTA
1
14
VDD
IN 2A
2
13
IN 2D
IN 2A
2
13
IN 3C
IN 2A
2
13
IN 2D
IN 1A
2
13
OUTB
OUTA
3
12
IN 1D
IN 1B
3
12
IN 2C
OUTA
3
12
IN 1D
IN 2A
3
12
IN 4B
OUTB
4
11
OUTD
IN 2B
4
11
IN 1C
OUTB
4
11
OUTD
IN 3A
4
11
IN 3B
IN 1B
5
10
OUTC
IN 3B
5
10
OUTC
IN 1B
5
10
OUTC
IN 4A
5
10
IN 2B
IN 2B
6
9
IN 2C
OUTB
6
9
OUTA
IN 2B
6
9
IN 2C
NC
6
9
IN 1B
VSS
7
8
IN 1C
VSS
7
8
IN 3A
VSS
7
8
IN 1C
VSS
7
8
NC
NC = NO CONNECTION
http://onsemi.com
2
MC14001B Series
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ELECTRICAL CHARACTERISTICS (Voltages Referenced to VSS)
Characteristic
Output Voltage
Vin = VDD or 0
Symbol
− 55C
25C
125C
VDD
Vdc
Min
Max
Min
Typ (2)
Max
Min
Max
Unit
“0” Level
VOL
5.0
10
15
−
−
−
0.05
0.05
0.05
−
−
−
0
0
0
0.05
0.05
0.05
−
−
−
0.05
0.05
0.05
Vdc
“1” Level
VOH
5.0
10
15
4.95
9.95
14.95
−
−
−
4.95
9.95
14.95
5.0
10
15
−
−
−
4.95
9.95
14.95
−
−
−
Vdc
Input Voltage
“0” Level
(VO = 4.5 or 0.5 Vdc)
(VO = 9.0 or 1.0 Vdc)
(VO = 13.5 or 1.5 Vdc)
VIL
5.0
10
15
−
−
−
1.5
3.0
4.0
−
−
−
2.25
4.50
6.75
1.5
3.0
4.0
−
−
−
1.5
3.0
4.0
“1” Level
VIH
5.0
10
15
3.5
7.0
11
−
−
−
3.5
7.0
11
2.75
5.50
8.25
−
−
−
3.5
7.0
11
−
−
−
5.0
5.0
10
15
– 3.0
– 0.64
– 1.6
– 4.2
−
−
−
−
– 2.4
– 0.51
– 1.3
– 3.4
– 4.2
– 0.88
– 2.25
– 8.8
−
−
−
−
– 1.7
– 0.36
– 0.9
– 2.4
−
−
−
−
IOL
5.0
10
15
0.64
1.6
4.2
−
−
−
0.51
1.3
3.4
0.88
2.25
8.8
−
−
−
0.36
0.9
2.4
−
−
−
mAdc
Input Current
Iin
15
−
± 0.1
−
± 0.00001
± 0.1
−
± 1.0
Adc
Input Capacitance
(Vin = 0)
Cin
−
−
−
−
5.0
7.5
−
−
pF
Quiescent Current
(Per Package)
IDD
5.0
10
15
−
−
−
0.25
0.5
1.0
−
−
−
0.0005
0.0010
0.0015
0.25
0.5
1.0
−
−
−
7.5
15
30
Adc
IT
5.0
10
15
Vin = 0 or VDD
(VO = 0.5 or 4.5 Vdc)
(VO = 1.0 or 9.0 Vdc)
(VO = 1.5 or 13.5 Vdc)
Output Drive Current
(VOH = 2.5 Vdc)
(VOH = 4.6 Vdc)
(VOH = 9.5 Vdc)
(VOH = 13.5 Vdc)
Vdc
Vdc
IOH
Source
(VOL = 0.4 Vdc)
(VOL = 0.5 Vdc)
(VOL = 1.5 Vdc)
Total Supply Current (3) (4)
(Dynamic plus Quiescent,
Per Gate, CL = 50 pF)
Sink
mAdc
IT = (0.3 A/kHz) f + IDD/N
IT = (0.6 A/kHz) f + IDD/N
IT = (0.9 A/kHz) f + IDD/N
Adc
2. Data labelled “Typ” is not to be used for design purposes but is intended as an indication of the IC’s potential performance.
3. The formulas given are for the typical characteristics only at 25C.
4. To calculate total supply current at loads other than 50 pF:
IT(CL) = IT(50 pF) + (CL − 50) Vfk
where: IT is in A (per package), CL in pF, V = (VDD − VSS) in volts, f in kHz is input frequency, and k = 0.001 x the number of exercised gates
per package.
http://onsemi.com
3
MC14001B Series
B−SERIES GATE SWITCHING TIMES
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
SWITCHING CHARACTERISTICS (5) (CL = 50 pF, TA = 25C)
Characteristic
Symbol
Output Rise Time, All B−Series Gates
tTLH = (1.35 ns/pF) CL + 33 ns
tTLH = (0.60 ns/pF) CL + 20 ns
tTLH = (0.40 ns/PF) CL + 20 ns
tTLH
Output Fall Time, All B−Series Gates
tTHL = (1.35 ns/pF) CL + 33 ns
tTHL = (0.60 ns/pF) CL + 20 ns
tTHL = (0.40 ns/pF) CL + 20 ns
tTHL
Propagation Delay Time
MC14001B, MC14011B only
tPLH, tPHL = (0.90 ns/pF) CL + 80 ns
tPLH, tPHL = (0.36 ns/pF) CL + 32 ns
tPLH, tPHL = (0.26 ns/pF) CL + 27 ns
All Other 2, 3, and 4 Input Gates
tPLH, tPHL = (0.90 ns/pF) CL + 115 ns
tPLH, tPHL = (0.36 ns/pF) CL + 47 ns
tPLH, tPHL = (0.26 ns/pF) CL + 37 ns
8−Input Gates (MC14068B, MC14078B)
tPLH, tPHL = (0.90 ns/pF) CL + 155 ns
tPLH, tPHL = (0.36 ns/pF) CL + 62 ns
tPLH, tPHL = (0.26 ns/pF) CL + 47 ns
VDD
Vdc
Min
Typ (6)
Max
5.0
10
15
−
−
−
100
50
40
200
100
80
5.0
10
15
−
−
−
100
50
40
200
100
80
Unit
ns
ns
tPLH, tPHL
ns
5.0
10
15
−
−
−
125
50
40
250
100
80
5.0
10
15
−
−
−
160
65
50
300
130
100
5.0
10
15
−
−
−
200
80
60
350
150
110
5. The formulas given are for the typical characteristics only at 25C.
6. Data labelled “Typ” is not to be used for design purposes but is intended as an indication of the IC’s potential performance.
14
PULSE
GENERATOR
20 ns
VDD
20 ns
INPUT
INPUT
OUTPUT
7
0V
tPLH
tPHL
CL
*
VDD
90%
50%
10%
OUTPUT
INVERTING
VSS
tTHL
tPLH
OUTPUT
NON−INVERTING
*All unused inputs of AND, NAND gates must be connected to VDD.
All unused inputs of OR, NOR gates must be connected to VSS.
tTLH
Figure 1. Switching Time Test Circuit and Waveforms
http://onsemi.com
4
VOH
90%
50%
10%
tTLH
tPHL
90%
50%
10%
tTHL
VOL
VOH
VOL
MC14001B Series
CIRCUIT SCHEMATIC
NOR, OR GATES
MC14001B, MC14071B
One of Four Gates Shown
MC14025B
One of Three Gates Shown
VDD
VDD
14
VDD
1, 6, 8, 13
1, 3, 11
*
2, 4, 12
2, 5, 9, 12
14
3, 4, 10, 11
VDD
*
VSS
VSS
7
9, 6, 10
VSS
VDD
*Inverter omitted in MC14001B
8, 5, 13
7
VSS
VSS
*Inverter omitted in MC14025B
CIRCUIT SCHEMATIC
NAND, AND GATES
MC14023B, MC14073B
One of Three Gates Shown
MC14011B, MC14081B
One of Four Gates Shown
VDD
14
VDD
*
3, 4, 10, 11
2, 4, 12
1, 3, 11
14
VSS
VDD
2, 5, 9, 12
VDD
1, 6, 8, 13
7 VSS
*Inverter omitted in MC14011B
*
9, 6, 10
8, 5, 13
VSS
7
VSS
*Inverter omitted in MC14023B
http://onsemi.com
5
MC14001B Series
TYPICAL B−SERIES GATE CHARACTERISTICS
N−CHANNEL DRAIN CURRENT (SINK)
P−CHANNEL DRAIN CURRENT (SOURCE)
− 10
5.0
ID , DRAIN CURRENT (mA)
ID , DRAIN CURRENT (mA)
− 9.0
4.0
TA = − 55°C
3.0
− 40°C
+ 85°C + 25°C
2.0
+ 125°C
1.0
− 8.0
TA = − 55°C
− 7.0
− 40°C
− 6.0
− 5.0
+ 25°C
+ 85°C
− 4.0
+ 125°C
− 3.0
− 2.0
− 1.0
0
0
1.0
2.0
3.0
4.0
VDS, DRAIN−TO−SOURCE VOLTAGE (Vdc)
0
5.0
0
Figure 2. VGS = 5.0 Vdc
− 50
− 45
TA = − 55°C
16
14
− 40°C
12
+ 25°C
+ 85°C
10
ID , DRAIN CURRENT (mA)
ID , DRAIN CURRENT (mA)
18
+ 125°C
8.0
6.0
− 40
− 35
− 30
− 5.0
2.0 3.0 4.0 5.0
6.0
7.0 8.0
VDS, DRAIN−TO−SOURCE VOLTAGE (Vdc)
9.0
0
10
+ 85°C
− 15
2.0
1.0
+ 125°C
0
Figure 4. VGS = 10 Vdc
− 100
45
− 90
30
− 40°C
25
+ 25°C
ID , DRAIN CURRENT (mA)
ID , DRAIN CURRENT (mA)
40
TA = − 55°C
+ 85°C
20
+ 125°C
15
− 1.0 − 2.0 − 3.0 − 4.0 − 5.0 − 6.0 − 7.0 − 8.0 − 9.0 − 10
VDS, DRAIN−TO−SOURCE VOLTAGE (Vdc)
Figure 5. VGS = − 10 Vdc
50
35
− 40°C
+ 25°C
− 20
− 10
0
TA = − 55°C
− 25
4.0
10
5.0
0
− 5.0
Figure 3. VGS = − 5.0 Vdc
20
0
− 1.0
− 2.0
− 3.0
− 4.0
VDS, DRAIN−TO−SOURCE VOLTAGE (Vdc)
− 80
− 70
− 60
TA = − 55°C
− 50
− 40°C
+ 25°C
− 40
+ 85°C
− 30
+ 125°C
− 20
− 10
0
2.0
4.0 6.0 8.0 10
12
14
16
VDS, DRAIN−TO−SOURCE VOLTAGE (Vdc)
18
0
20
0
Figure 6. VGS = 15 Vdc
− 2.0 − 4.0 − 6.0 − 8.0 − 10 − 12 − 14 − 16
VDS, DRAIN−TO−SOURCE VOLTAGE (Vdc)
Figure 7. VGS = − 15 Vdc
These typical curves are not guarantees, but are design aids.
Caution: The maximum rating for output current is 10 mA per pin.
http://onsemi.com
6
− 18 − 20
MC14001B Series
TYPICAL B−SERIES GATE CHARACTERISTICS (cont’d)
V out , OUTPUT VOLTAGE (Vdc)
V out , OUTPUT VOLTAGE (Vdc)
VOLTAGE TRANSFER CHARACTERISTICS
SINGLE INPUT NAND, AND
MULTIPLE INPUT NOR, OR
5.0
4.0
SINGLE INPUT NOR, OR
MULTIPLE INPUT NAND, AND
3.0
2.0
1.0
0
0
1.0
2.0
SINGLE INPUT NAND, AND
MULTIPLE INPUT NOR, OR
10
8.0
SINGLE INPUT NOR, OR
MULTIPLE INPUT NAND, AND
6.0
4.0
2.0
0
3.0
4.0
5.0
Vin, INPUT VOLTAGE (Vdc)
0
2.0
Figure 8. VDD = 5.0 Vdc
V out , OUTPUT VOLTAGE (Vdc)
6.0
8.0
10
Vin, INPUT VOLTAGE (Vdc)
Figure 9. VDD = 10 Vdc
DC NOISE MARGIN
16
SINGLE INPUT NAND, AND
MULTIPLE INPUT NOR, OR
14
The DC noise margin is defined as the input voltage range
from an ideal “1” or “0” input level which does not produce
output state change(s). The typical and guaranteed limit
values of the input values VIL and VIH for the output(s) to
be at a fixed voltage VO are given in the Electrical
Characteristics table. VIL and VIH are presented graphically
in Figure 11.
Guaranteed minimum noise margins for both the “1” and
“0” levels =
12
SINGLE INPUT NOR, OR
MULTIPLE INPUT NAND, AND
10
8.0
6.0
4.0
2.0
0
4.0
0
2.0
4.0
1.0 V with a 5.0 V supply
2.0 V with a 10.0 V supply
2.5 V with a 15.0 V supply
6.0
8.0
10
Vin, INPUT VOLTAGE (Vdc)
Figure 10. VDD = 15 Vdc
Vout
VDD
Vout
VO
VO
VO
VO
VDD
VDD
0
VDD
Vin
VIL
0
VIH
Vin
VIL
VIH
VSS = 0 VOLTS DC
(a) Inverting Function
(b) Non−Inverting Function
Figure 11. DC Noise Immunity
http://onsemi.com
7
MC14001B Series
ORDERING INFORMATION
Package
Shipping†
MC14001BCP
PDIP−14
2000 Units / Box
MC14001BCPG
PDIP−14
(Pb−Free)
2000 Units / Box
MC14001BD
SOIC−14
2750 Units / Box
MC14001BDR2
SOIC−14
2500 Units / Tape & Reel
MC14001BDR2G
SOIC−14
(Pb−Free)
2500 Units / Tape & Reel
MC14001BDTR2
TSSOP−14*
2500 Units / Tape & Reel
MC14001BFEL
SOEIAJ−14
2000 Units / Tape & Reel
MC14001BFELG
SOEIAJ−14
(Pb−Free)
2000 Units / Tape & Reel
MC14011BCP
PDIP−14
2000 Units / Box
MC14011BCPG
PDIP−14
(Pb−Free)
2000 Units / Box
MC14011BD
SOIC−14
2750 Units / Box
MC14011BDR2
SOIC−14
2500 Units / Tape & Reel
MC14011BDR2G
SOIC−14
(Pb−Free)
2500 Units / Tape & Reel
MC14011BDTR2
TSSOP−14*
2500 Units / Tape & Reel
MC14011BF
SOEIAJ−14
55 Units / Rail
MC14011BFEL
SOEIAJ−14
2000 Units / Tape & Reel
MC14011BFELG
SOEIAJ−14
(Pb−Free)
2000 Units / Tape & Reel
MC14023BCP
PDIP−14
2000 Units / Box
MC14023BCPG
PDIP−14
(Pb−Free)
2000 Units / Box
MC14023BD
SOIC−14
2750 Units / Box
MC14023BDR2
SOIC−14
2500 Units / Tape & Reel
MC14023BDR2G
SOIC−14
(Pb−Free)
2500 Units / Tape & Reel
MC14023BFEL
SOEIAJ−14
2000 Units / Tape & Reel
MC14025BCP
PDIP−14
2000 Units / Box
MC14025BCPG
PDIP−14
(Pb−Free)
2000 Units / Box
MC14025BD
SOIC−14
2750 Units / Box
MC14025BDR2
SOIC−14
2500 Units / Tape & Reel
MC14025BDR2G
SOIC−14
(Pb−Free)
2500 Units / Tape & Reel
SOEIAJ−14
2000 Units / Tape & Reel
Device
MC14025BFEL
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*This package is inherently Pb−Free.
http://onsemi.com
8
MC14001B Series
ORDERING INFORMATION
Package
Shipping†
MC14071BCP
PDIP−14
2000 Units / Box
MC14071BD
SOIC−14
55 Units / Rail
MC14071BDR2
SOIC−14
2500 Units / Tape & Reel
MC14071BDR2G
SOIC−14
(Pb−Free)
2500 Units / Tape & Reel
MC14071BDT
TSSOP−14*
96 Units per Rail
MC14071BDTR2
TSSOP−14*
2500 Units / Tape & Reel
MC14071BFEL
SOEIAJ−14
2000 Units / Tape & Reel
MC14073BCP
PDIP−14
2000 Units / Box
MC14073BCPG
PDIP−14
(Pb−Free)
2000 Units / Box
MC14073BD
SOIC−14
55 Units / Rail
MC14073BDG
SOIC−14
(Pb−Free)
55 Units / Rail
MC14073BDR2
SOIC−14
2500 Units / Tape & Reel
MC14073BDR2G
SOIC−14
(Pb−Free)
2500 Units / Tape & Reel
MC14073BFEL
SOEIAJ−14
2000 Units / Tape & Reel
MC14081BCP
PDIP−14
2000 Units / Box
MC14081BCPG
PDIP−14
(Pb−Free)
2000 Units / Box
MC14081BD
SOIC−14
55 Units / Rail
MC14081BDG
SOIC−14
(Pb−Free)
55 Units / Rail
MC14081BDR2
SOIC−14
2500 Units / Tape & Reel
MC14081BDR2G
SOIC−14
(Pb−Free)
2500 Units / Tape & Reel
MC14081BDTR2
TSSOP−14*
2500 Units / Tape & Reel
MC14081BFEL
SOEIAJ−14
2000 Units / Tape & Reel
MC14081BFELG
SOEIAJ−14
(Pb−Free)
2000 Units / Tape & Reel
MC14082BCP
PDIP−14
2000 Units / Box
MC14082BCPG
PDIP−14
(Pb−Free)
2000 Units / Box
MC14082BD
SOIC−14
55 Units / Rail
MC14082BDG
SOIC−14
(Pb−Free)
55 Units / Rail
MC14082BDR2
SOIC−14
2500 Units / Tape & Reel
MC14082BDR2G
SOIC−14
(Pb−Free)
2500 Units / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*This package is inherently Pb−Free.
http://onsemi.com
9
MC14001B Series
PACKAGE DIMENSIONS
P SUFFIX
PLASTIC DIP PACKAGE
CASE 646−06
ISSUE N
14
NOTES:
1. DIMENSIONING AND TOLERANCING
PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS
WHEN FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE
MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
8
B
1
7
A
F
DIM
A
B
C
D
F
G
H
J
K
L
M
N
L
N
C
−T−
SEATING
PLANE
J
K
H
D 14 PL
G
M
0.13 (0.005)
M
INCHES
MIN
MAX
0.715
0.770
0.240
0.260
0.145
0.185
0.015
0.021
0.040
0.070
0.100 BSC
0.052
0.095
0.008
0.015
0.115
0.135
0.290
0.310
−−−
10 0.015
0.039
MILLIMETERS
MIN
MAX
18.16
18.80
6.10
6.60
3.69
4.69
0.38
0.53
1.02
1.78
2.54 BSC
1.32
2.41
0.20
0.38
2.92
3.43
7.37
7.87
−−−
10 0.38
1.01
D SUFFIX
PLASTIC SOIC PACKAGE
CASE 751A−03
ISSUE G
−A−
14
8
−B−
P 7 PL
0.25 (0.010)
M
B
M
7
1
G
F
R X 45 C
−T−
SEATING
PLANE
0.25 (0.010)
M
T B
J
M
K
D 14 PL
S
A
S
http://onsemi.com
10
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.127
(0.005) TOTAL IN EXCESS OF THE D
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
DIM
A
B
C
D
F
G
J
K
M
P
R
MILLIMETERS
MIN
MAX
8.55
8.75
3.80
4.00
1.35
1.75
0.35
0.49
0.40
1.25
1.27 BSC
0.19
0.25
0.10
0.25
0
7
5.80
6.20
0.25
0.50
INCHES
MIN
MAX
0.337 0.344
0.150 0.157
0.054 0.068
0.014 0.019
0.016 0.049
0.050 BSC
0.008 0.009
0.004 0.009
0
7
0.228 0.244
0.010 0.019
MC14001B Series
PACKAGE DIMENSIONS
DT SUFFIX
PLASTIC TSSOP PACKAGE
CASE 948G−01
ISSUE O
14X K REF
0.10 (0.004)
0.15 (0.006) T U
M
T U
V
S
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL
NOT EXCEED 0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08
(0.003) TOTAL IN EXCESS OF THE K
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE −W−.
S
S
N
2X
14
L/2
0.25 (0.010)
8
M
B
−U−
L
PIN 1
IDENT.
F
7
1
0.15 (0.006) T U
N
S
DETAIL E
K
A
−V−
ÉÉÉ
ÇÇÇ
ÇÇÇ
ÉÉÉ
K1
J J1
SECTION N−N
−W−
C
0.10 (0.004)
−T− SEATING
PLANE
D
G
H
DETAIL E
http://onsemi.com
11
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
MILLIMETERS
MIN
MAX
4.90
5.10
4.30
4.50
−−−
1.20
0.05
0.15
0.50
0.75
0.65 BSC
0.50
0.60
0.09
0.20
0.09
0.16
0.19
0.30
0.19
0.25
6.40 BSC
0
8
INCHES
MIN MAX
0.193 0.200
0.169 0.177
−−− 0.047
0.002 0.006
0.020 0.030
0.026 BSC
0.020 0.024
0.004 0.008
0.004 0.006
0.007 0.012
0.007 0.010
0.252 BSC
0
8
MC14001B Series
PACKAGE DIMENSIONS
F SUFFIX
PLASTIC EIAJ SOIC PACKAGE
CASE 965−01
ISSUE O
14
LE
8
Q1
E HE
L
7
1
M
DETAIL P
Z
D
VIEW P
A
e
c
0.13 (0.005)
DIM
A
A1
b
c
D
E
e
HE
0.50
LE
M
Q1
Z
A1
b
M
NOTES:
1 DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2 CONTROLLING DIMENSION: MILLIMETER.
3 DIMENSIONS D AND E DO NOT INCLUDE MOLD
FLASH OR PROTRUSIONS AND ARE MEASURED
AT THE PARTING LINE. MOLD FLASH OR
PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006)
PER SIDE.
4 TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
5 THE LEAD WIDTH DIMENSION (b) DOES NOT
INCLUDE DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08 (0.003)
TOTAL IN EXCESS OF THE LEAD WIDTH
DIMENSION AT MAXIMUM MATERIAL CONDITION.
DAMBAR CANNOT BE LOCATED ON THE LOWER
RADIUS OR THE FOOT. MINIMUM SPACE
BETWEEN PROTRUSIONS AND ADJACENT LEAD
TO BE 0.46 ( 0.018).
0.10 (0.004)
MILLIMETERS
MIN
MAX
−−−
2.05
0.05
0.20
0.35
0.50
0.18
0.27
9.90
10.50
5.10
5.45
1.27 BSC
7.40
8.20
0.50
0.85
1.10
1.50
10 0
0.70
0.90
−−−
1.42
INCHES
MIN
MAX
−−−
0.081
0.002
0.008
0.014
0.020
0.007
0.011
0.390
0.413
0.201
0.215
0.050 BSC
0.291
0.323
0.020
0.033
0.043
0.059
10 0
0.028
0.035
−−−
0.056
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Phone: 81−3−5773−3850
http://onsemi.com
12
For additional information, please contact your
local Sales Representative.
MC14001B/D
Similar pages