Freescale MC34702EKR2 3.0 a switch-mode power supply with linear regulator Datasheet

Freescale Semiconductor
Technical Data
Document Number: MC34702
Rev 6.0, 2/2007
3.0 A Switch-Mode Power
Supply with Linear Regulator
34702
The 34702 provides the means to efficiently supply the Freescale
Power QUICC™ I, II, and other families of Freescale
microprocessors and DSPs. The 34702 incorporates a highperformance switching regulator, providing the direct supply for the
microprocessor’s core, and a low dropout (LDO) linear regulator
control circuit providing the microprocessor I/O and bus voltage.
The switching regulator is a high-efficiency synchronous buck
regulator with integrated N-channel power MOSFETs to provide
protection features and to allow space-efficient, compact design.
The 34702 incorporates many advanced features; e.g., precisely
maintained up/down power sequencing, ensuring the proper
operation and protection of the CPU and power system.
POWER SUPPLY
INTEGRATED CIRCUIT
Features
•
•
•
•
•
•
•
•
•
EK (PB-FREE) SUFFIX
98AARH99137A
32-PIN SOICW
Operating Voltage from 2.8 V to 6.0 V
High-Accuracy Output Voltages
Fast Transient Response
Switcher Output Current Up to 3.0 A
Undervoltage Lockout and Overcurrent Protection
Enable Inputs and Programmable Watchdog Timer
Voltage Margining via I2C™ Bus
Reset with Programmable Power-ON Delay
Pb-Free Packaging Designated by Suffix Code EK
ORDERING INFORMATION
I2C is a trademark of Philips Corporation.
Device
Temperature
Range (TA)
Package
MC34702EK/R2
-40 to 85°C
32 SOICW
2.8 V to 6.0 V Input
34702
VIN2
VIN1
VBD
VBST
LDRV
CS
RT
Optional
VDDH (I/Os)
LFB
MPC8xxx
SDA
SCL
GND
CLKSEL
Adjustable:
0.8 V to VIN Dropout
LDO
ADDR
EN1
EN2
CLKSYN
Other
Circuits
PORESET
RST
BOOT
VBST
Adjustable:
0.8 V to VIN Dropout
SW
VOUT
PGND
FREQ
INV
VDDI
Figure 1. 34702 Simplified Application Diagram
Freescale Semiconductor, Inc. reserves the right to change the detail specifications,
as may be required, to permit improvements in the design of its products.
© Freescale Semiconductor, Inc., 2007. All rights reserved.
VDDL (Core)
INTERNAL BLOCK DIAGRAM
INTERNAL BLOCK DIAGRAM
VIN1
VIN
VDDI
Internal
Supply
VDDI
VDDI
8.0 V
VBST
VBST
VBST
-
VREF
Power
Enable
LDRV
VDDI
VDDI
+
VBD
Q5
Boost
Control
VREF
VREF
Bandgap
Voltage
Reference
Linear
Regulator
Control
CS
To Reset
Control
LDO
ILim
VREF
LFB
VDDI
LCMP
Power
Sequencing
EN2
Reset
RST
Q6
RT
Power
Seq
VLDO
EN1
Reset
Control
POR
Timer
I2C
Control
Power
Down
VOUT
VBST
SysCon
BOOT
Current Limit
I 2C
VIN2
(2)
VDDI
Control
Thermal
Limit
VBST
Voltage Margining
Watchdog Timer
INV
LFB
UVLO
Q4
SysCon
Buck
HS
and
LS
Driver
Buck
Control
Logic
SoftSt
Q1
SW
(2)
Q2
ADDR
SDA
I2C
Interface
PGND
(2)
SCL
PWM
Comp
Switcher
Oscillator
300 kHz
-
CLKSYN FREQ
0.8 V
+
To Reset
Control
-
INV
VOUT
Ramp
Gen.
CLKSEL
+
Error
Amp
Power
Seq
VOUT
Q3
GND (4)
Figure 2. 34702 Simplified Internal Block Diagram
34702
2
Analog Integrated Circuit Device Data
Freescale Semiconductor
PIN CONNECTIONS
PIN CONNECTIONS
FREQ
INV
VOUT
VIN2
VIN2
SW
SW
GND
GND
PGND
PGND
VBD
VBST
BOOT
SDA
SCL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
CLKSYN
CLKSEL
RST
RT
EN2
EN1
ADDR
GND
GND
VDD1
VIN1
LDRV
CS
LDO
LFB
LCMP
Figure 3. Pin Connections
Table 1.
Pin Function Description
A functional description of each pin can be found in the Functional Pin Description section beginning on page 16.
Pin
Pin Name
Formal Name
Definition
1
FREQ
Oscillator Frequency
This switcher frequency selection pin can be adjusted by connecting external
resistor RF to the FREQ pin. The default switching frequency (FREQ pin left open or
tied to VDDI) is set to 300 kHz.
2
INV
Inverting Input
Buck Controller Error Amplifier inverting input.
3
VOUT
Output Voltage
Output voltage of the buck converter. Input pin of the switching regulator power
sequence control circuit.
4, 5
VIN2
Input Voltage 2
Buck regulator power input. Drain of the high-side power MOSFET.
6, 7
SW
Switch
Buck regulator switching node. This pin is connected to the inductor.
8, 9
24, 25
GND
Ground
Analog ground of the IC, thermal heatsinking.
10, 11
PGND
Power Ground
12
VBD
Boost Drain
13
VBST
Boost Voltage
14
BOOT
Bootstrap
15
SDA
Serial Data
I2C bus pin. Serial data.
16
SCL
Serial Clock
I2C bus pin. Serial clock.
17
LCMP
Linear Compensation
18
LFB
Linear Feedback
Linear regulator feedback pin.
19
LDO
Linear Regulator
Input pin of the linear regulator power sequence control circuit.
Buck regulator power ground.
Drain of the internal boost regulator power MOSFET.
Internal boost regulator output voltage. The internal boost regulator provides a
20 mA output current to supply the drive circuits for the integrated power MOSFETs
and the external N-channel power MOSFET of the linear regulator. The voltage at
the VBST pin is 7.75V nominal.
Bootstrap capacitor input.
Linear regulator compensation pin.
34702
Analog Integrated Circuit Device Data
Freescale Semiconductor
3
PIN CONNECTIONS
Table 1.
Pin Function Description (continued)
A functional description of each pin can be found in the Functional Pin Description section beginning on page 16.
Pin
Pin Name
Formal Name
Definition
20
CS
Current Sense
Current sense pin of the LDO. Overcurrent protection of the linear regulator external
power MOSFET. The voltage drop over the LDO current sense resistor RS is sensed
between the CS and LDO pins. The LDO current limit can be adjusted by selecting
the proper value of the current sensing resistor RS.
21
LDRV
Linear Drive
22
VIN1
Input Voltage 1
The input supply pin for the integrated circuit. The internal circuits of the IC are
supplied through this pin.
23
VDDI
Power Supply
Internal supply voltage. A ceramic low ESR 1uF 6V X5R or X7R capacitor is
recommended.
26
ADDR
Address
I2C address selection. This pin can either be left open, tied to VDDI, or grounded
through a 10 kΩ resistor.
27
EN1
Enable 1
Enable 1 Input. The combination of the logic state of the Enable 1 and Enable 2
inputs determines operation mode and type of power sequencing of the IC.
28
EN2
Enable 2
Enable 2 Input. The combination of the logic state of the Enable 1 and Enable 2
inputs determines operation mode and type of power sequencing of the IC.
29
RT
Reset Timer
This pin allows programming of the Power-ON Reset delay by means of an external
RC network.
30
RST
Reset Output
(Active LOW)
The Reset Control circuit monitors both the switching regulator and the LDO
feedback voltages. It is an open drain output and has to be pulled up to some supply
voltage (e.g., the output of the LDO) by an external resistor.
31
CLKSEL
Clock Selection
This pin sets the CLKSYN pin as either an oscillator output or a synchronization input
pin. The CLKSEL pin is also used for the I2C address selection.
32
CLKSYN
Clock Synchronization
LDO gate drive of the external pass N-channel MOSFET.
Oscillator output/synchronization input pin.
34702
4
Analog Integrated Circuit Device Data
Freescale Semiconductor
ELECTRICAL CHARACTERISTICS
MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
MAXIMUM RATINGS
Table 2. Maximum Ratings
All voltages are with respect to ground unless otherwise noted. Exceeding these ratings may cause a malfunction or permanent
damage to the device.
Rating
Symbol
Value
Unit
VIN1, VIN2
-0.3 to 7.0
V
VSW
-1.0 to 7.0
V
VIN(BOOT)
-0.3 to 8.5
V
Boost Regulator Output Voltage
VBST
-0.3 to 8.5
V
Boost Regulator Drain Voltage
VBD
-0.3 to 9.5
V
RST Drain Voltage
VRST
-0.3 to 7.0
V
Enable Pin Voltage at EN1, EN2
VEN
-0.3 to 7.0
V
VLOG
-0.3 to 7.0
V
LDO, VOUT, RST
VOUT
-0.3 to 7.0
LDRV, LCMP, CS
VLIN
-0.3 to 8.5
VLOGIC
-0.3 to 3.6
VESD
±2000
ELECTRICAL RATINGS
Supply Voltage
Switching Node Voltage
Buck Regulator Bootstrap Input Voltage (BOOT - SW)
Logic Pin Voltage at SDA, SCL
Analog Pin Voltage
Pin Voltage at CLKSEL, ADDR, RT, FREQ, VDDI, CLKSYN, INV, LFB
V
ESD Voltage (1)
Human Body Model
Machine Model
V
V
±200
Notes
1. ESD1 testing is performed in accordance with the Human Body Model (CZAP = 100 pF, RZAP = 1500 Ω), ESD2 testing is performed in
accordance with the Machine Model (CZAP = 200 pF, RZAP = 0 Ω), and the Charge Device Model.
34702
Analog Integrated Circuit Device Data
Freescale Semiconductor
5
ELECTRICAL CHARACTERISTICS
MAXIMUM RATINGS
Table 2. Maximum Ratings (continued)
All voltages are with respect to ground unless otherwise noted. Exceeding these ratings may cause a malfunction or permanent
damage to the device.
Rating
Symbol
Value
Unit
TSTG
-65 to 150
°C
TPPRT
Note 3
°C
TJMAX
125
°C
THERMAL RATINGS
Storage Temperature
Peak Package Reflow Temperature During Reflow
(2) (3)
,
Maximum Junction Temperature
°C/W
RθJA
Thermal Resistance
(4) (5)
70
Junction to Ambient (Four Layers) (4), (5)
55
Junction to Ambient (Single Layer)
,
Thermal Resistance, Junction to Base (6)
Operational Package Temperature (Ambient Temperature)
RθJB
18
°C/W
TA
-40 to 85
°C
Notes
2. Pin soldering temperature limit is for 10 seconds maximum duration. Not designed for immersion soldering. Exceeding these limits may
cause malfunction or permanent damage to the device.
3. Freescale’s Package Reflow capability meets Pb-free requirements for JEDEC standard J-STD-020C. For Peak Package Reflow
Temperature and Moisture Sensitivity Levels (MSL),
Go to www.freescale.com, search by part number [e.g. remove prefixes/suffixes and enter the core ID to view all orderable parts. (i.e.
MC33xxxD enter 33xxx), and review parametrics..
4. Junction temperature is a function of on-chip power dissipation, package thermal resistance, mounting site (board) temperature,
ambient temperature, air flow, power dissipation of other components on the board and board thermal resistance.
5. Per JEDEC JESD51-6 with the board horizontal
6. Thermal resistance between the die and the printed circuit board per JEDEC JESD51-8. Board temperature is measured on the top
surface of the board near the package.
34702
6
Analog Integrated Circuit Device Data
Freescale Semiconductor
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 3. Static Electrical Characteristics
Characteristics noted under conditions -40°C ≤ TA ≤ 85°C unless otherwise noted. Input voltages VIN1 = VIN2 = 3.3 V using
the typical application circuit (see Figure 33) unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
Operating Voltage Range (VIN1, VIN2)
VIN
2.8
–
6.0
V
Start-Up Voltage Threshold (Boost Switching)
VST
–
1.6
1.8
V
VBST_UVLO
5.5
–
6.5
V
VBST_UVLO_HYS
0.5
–
1.5
V
Input DC Supply Current (Normal Operation Mode, Enabled), Unloaded
Outputs
IIN
–
60
–
mA
VIN1 Pin Input Supply Current (EN1 = EN2 = 0)
IIN1
–
10
–
mA
VIN2 Pin Input Leakage Current (EN1 = EN2 = 0)
IIN2
–
100
–
µA
VDDI Internal Supply Voltage
VDDI
2.9
–
3.3
V
VDDI Maximum Output Current (Externally Loaded)
IDDI
–
–
-10
mA
0.784
0.800
0.816
VMVO
–
1.0
–
%
Buck Converter Voltage Margining Highest Positive Value
VMP
5.9
7.0
7.9
%
Buck Converter Voltage Margining Lowest Negative Value
VMN
-7.9
7.0
-5.9
%
-1.0
–
1.0
-1.0
–
1.0
–
3.5
–
GENERAL
VBST Undervoltage Lockout (VBST rising)
VBST Undervoltage Lockout Hysterisis
BUCK CONVERTER
Buck Converter Feedback Voltage (7), (8)
Buck Converter Voltage Margining Step Size
Buck Converter Line Regulation
(7), (8)
REGLNVO
VIN1 = VIN2 = 2.8 V to 6.0 V, I VOUT = 15 mA to 3.0 A
Buck Converter Load Regulation (7), (8)
%
mA
IVOUTLK
VOUT = 5.25 V
INV Input Leakage Current
%
REGLDVO
VIN1 = VIN2 = 2.8 V to 6.0 V, I VOUT = 15 mA to 3.0 A
VOUT Input Leakage Current
V
VINV
I VOUT = 15 mA to 3.0 A. Includes Load Regulation Error
INVLEAK
-1.0
1.0
µA
INV = 0.8 V
Notes
7. Design information only. This parameter is not production tested.
8. VOUT refers to load current on output switcher.
34702
Analog Integrated Circuit Device Data
Freescale Semiconductor
7
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 3. Static Electrical Characteristics (continued)
Characteristics noted under conditions -40°C ≤ TA ≤ 85°C unless otherwise noted. Input voltages VIN1 = VIN2 = 3.3 V using
the typical application circuit (see Figure 33) unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
–
60
–
Unit
BUCK CONVERTER (CONTINUED)
High-Side Power MOSFET Q1 RDS(ON) (9),(10)
ID = 500 mA, TA = 25°C, VBST = 8.0 V
Low-Side Power MOSFET Q2 RDS(ON) (9),(10)
VOUT Pulldown MOSFET Q3 Current Limit
–
65
–
-7.0
-4.7
-4.0
0.75
–
2.0
–
–
1.9
TSD
150
170
190
°C
TSDHYS
–
10
–
°C
ILIMH
Thermal Shutdown (VOUT Pull-down MOSFET Q3) (9)
Thermal Shutdown Hysteresis (9)
Ω
RDS(ON)
ID = 1.0 A, VBST = 8.0 V
A
A
IM3_LIM
TA = 25°C, VBST = 8.0 V
VOUT Pull-down MOSFET Q3 RDS(ON)(10)
mΩ
RDS(ON)
ID = 500 mA, TA = 25°C, VBST = 8.0 V
Buck Converter Peak Current Limit (High Level)
mΩ
RDS(ON)
Notes
9. Design information only. This parameter is not production tested.
10. ID refers to the MOSFET drain current
34702
8
Analog Integrated Circuit Device Data
Freescale Semiconductor
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 3. Static Electrical Characteristics (continued)
Characteristics noted under conditions -40°C ≤ TA ≤ 85°C unless otherwise noted. Input voltages VIN1 = VIN2 = 3.3 V using
the typical application circuit (see Figure 33) unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
ROUT
–
150
–
Ω
AVOL
–
80
–
dB
GBW
–
35
–
MHz
SR
–
200
–
V/µs
–
2.0
–
–
0.4
–
VSCRamp
–
0.5
–
V
VSCRamp
–
0.5
–
V
VOSC_OL
–
–
0.4
V
VOSC_OH
VDDI
ERROR AMPLIFIER (BUCK CONVERTER)
Input Impedance (11)
Output Impedance (11)
DC Open Loop Gain
(11)
Gain Bandwidth Product (11)
Slew Rate
(11)
V
VEA_OH
Output Voltage – High Level
Output Voltage – Low Level
IOEA = -1.0 mA
V
VEA_OL
VIN1 > 3.3 V, IOEA = -1.0 mA (11), (12)
(11), (12)
Oscillator Ramp (11)
OSCILLATOR
CLKSYN Pin (open) Low Level Output Voltage
IOL = +1.0
mA (13)
CLKSYN Pin (open) High Level Output Voltage
IOH = -1.0 mA
(14)
CLKSYN Pin (grounded) Input Voltage Threshold
CLKSYN Pin Pullup Resistance
Frequency Adjusting Reference Voltage
V
- 0.4 V
–
–
VOSC_IH
1.2
–
2.0
V
RPU
60
–
240
kΩ
VFREQ
–
1.26
–
V
7.3
7.7
8.3
BOOST REGULATOR
Regulator Output Voltage
Power MOSFET Q5 RDS(ON)(11)
Regulator Recommended Output Capacitor Maximum ESR
Notes
11.
12.
13.
14.
mΩ
RDS(ON)
IBD = 500 mA, TA = 25°C
Regulator Recommended Output Capacitor
V
VBST
IBST = 20 mA, VIN1 = VIN2 = 2.8 V to 6.0 V
–
650
1000
CBST
–
10
–
µF
ESRCBST
–
100
–
mΩ
Design information only. This parameter is not production tested.
IOEA Refers to Error Amplifier Output Current.
IOL Refers to IO Low Level Threshold Voltage Current
IOH Refers to IO High Level Threshold Voltage Current
34702
Analog Integrated Circuit Device Data
Freescale Semiconductor
9
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 3. Static Electrical Characteristics (continued)
Characteristics noted under conditions -40°C ≤ TA ≤ 85°C unless otherwise noted. Input voltages VIN1 = VIN2 = 3.3 V using
the typical application circuit (see Figure 33) unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
LINEAR REGULATOR (LDO)
LDO Feedback Voltage (16)
VLFB
VIN1 = VIN2 = 2.8 V to 6.0 V, ILDO = 10 mA to 1000 mA. Includes Load
Regulation Error
V
0.784
0.800
0.816
VMLDO
–
1.0
–
%
LDO Voltage Margining Highest Positive Value
VMP
5.9
7.0
7.9
%
LDO Voltage Margining Lowest Negative Value
VMN
-7.9
7.0
-5.9
%
-1.0
–
1.0
LDO Voltage Margining Step Size
LDO Line Regulation (16)
LDO Load Regulation (16)
%
REGLDVLDO
ILDO = 10 mA to 1000 mA
LDO Ripple Rejection, Dropout Voltage
%
REGLNVLDO
VIN1 = VIN2 = 2.8 V to 6.0 V, ILDO = 1000 mA
(16)
-1.0
–
1.0
–
40
–
dB
VLDO_RR
VDO = 1.0 V, VRIPPLE = +1.0 V p-p
Sinusoidal, f = 300 kHz, ILDO = 500 mA (15)
LDO Maximum Dropout Voltage (VIN - VLDO), using IRL2703 (16)
mV
VDO
VLDO = 2.5 V, ILDO = 1000 mA
–
50
75
VCSTH
35
50
65
mV
LDO Pin Input Current, VLDO = 5.25 V
ILDO
1.0
1.9
4.0
mA
LDO Feedback Input Current (LFB Pin), VLFB = 0.8 V
ILFB
-1.0
–
1.0
µA
LDO Drive Output Current (LDRV Pin), VLDRV = 0 V
ILDRV
-5.0
-3.3
-2.0
mA
CS Pin Input Leakage Current
ICSLK
50
–
200
0.75
–
2.0
–
–
1.9
CLDO
–
10
–
µF
ESRCLDO
–
5.0
–
mΩ
TSD
150
170
190
°C
TSDHYS
–
10
–
°C
LDO Current Sense Comparator Threshold Voltage (VCS - VLDO)
µA
VCS = 5.25 V
LDO Pulldown MOSFET Q4 Current Limit
LDO Pulldown MOSFET Q4 RDS(ON)
A
IM4_LIM
TA = 25°C, VBST = 8.0 V (LDO Pin)
LDO Recommended Output Capacitance
LDO Recommended Output Capacitor ESR
Thermal Shutdown (LDO Pull-down MOSFET Q4) (15)
Thermal Shutdown Hysteresis (15)
Ω
RDS(ON)
ID = 1.0 A, VBST = 8.0 V
Notes
15. Design information only. This parameter is not production tested.
16. IDO refers to Load Current on External LDOFET - IRL2703 is the Intersil MOSFET IRL2703
34702
10
Analog Integrated Circuit Device Data
Freescale Semiconductor
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 3. Static Electrical Characteristics (continued)
Characteristics noted under conditions -40°C ≤ TA ≤ 85°C unless otherwise noted. Input voltages VIN1 = VIN2 = 3.3 V using
the typical application circuit (see Figure 33) unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
VTH_EN
1.0
1.5
2.0
V
Enable (EN1, EN2) Pulldown Resistance
RPU
30
55
90
kΩ
RST Low-Level Output Voltage, IOL = 5.0 mA
VOL
–
–
0.4
V
ILKG-RST
–
–
10
µA
VOUTI Th
-14
–
-0.5
%
RST Overvoltage Threshold on VOUT (∆VOUT/VOUT) (17)
VOUTI Th
0.5
–
14
%
RST Undervoltage Threshold on VLDO (∆VLDO/VLDO) (17)
VLDOI Th
-12
–
-4.0
%
VLDOI Th
4.0
–
12
%
VTH-RT
1.0
1.2
1.5
V
IS-RT
-17
–
-34
mA
RST Timer Leakage Current
ILKG-RT
-1.0
–
1.0
µA
RST Timer Saturation Voltage, Reset Timer Current = 300 µA
VSAT-RT
–
35
100
mV
Maximum Recommended Value of the Reset Timer Capacitor
Ct
–
–
47
µF
CLKSEL Threshold Voltage
VTHCLKS
1.2
1.6
2.0
V
CLKSEL Pullup Resistance
RPU-CLKS
60
120
240
kΩ
ADDR Threshold Voltage (17)
VTHADDR
1.2
1.6
2.0
V
ADDR Pullup Resistance
RPU-ADDR
60
120
240
kΩ
TLIM
150
170
190
°C
TLIMHYS
–
10
–
°C
Input Threshold Voltage (Pin SCL), Rising Edge (17)
VLTH
1.3
–
1.7
V
Input Threshold Voltage (Pin SDA)
VLTH
1.3
–
1.7
V
II
–
1.0
10
µA
VOL
–
–
0.4
V
CINPUT
–
7.0
10
pF
CONTROL AND SUPERVISORY CIRCUITS
Enable (EN1, EN2) Input Voltage Threshold
RST Leakage Current, OFF State, Pulled Up to 5.25 V
RST Undervoltage Threshold on VOUT (∆VOUT/VOUT)
RST Overvoltage Threshold on VLDO (∆VLDO/VLDO)
(17)
(17)
RST Timer Voltage Threshold
RST Timer Source Current (RT pin at 0 V)
Thermal Shutdown (IC sensor) (17)
Thermal Shutdown Hysteresis
(17)
SDA, SCL PINS I2C BUS (STANDARD)
SDA, SCL Input Current, Input Voltage = 5.25 V (VIN1)
SDA Low-Level Output Voltage, 3.0 mA Sink Current
SDA, SCL Capacitance
(17)
Notes
17. Design information only. This parameter is not production tested.
34702
Analog Integrated Circuit Device Data
Freescale Semiconductor
11
ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
Table 4. DYNAMIC ELECTRICAL CHARACTERISTICS
Characteristics noted under conditions -40°C ≤ TA ≤ 85°C unless otherwise noted. Input voltages VIN1 = VIN2 = 3.3 V using
the typical application circuit (see Figures 33) unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
D
0
–
95
%
BUCK CONVERTER
Duty Cycle Range (Normal Operation) (18)
Switching Node SW Rise Time (18)
VIN = 5.0 V, ILOAD = 1.0 A
Switching Node SW Fall Time
(18)
Maximum Deadtime (18)
tD
(18)
7.0
–
–
17
–
–
35
–
ns
Soft Start Duration (Power Sequencing Disabled, EN1 = 1, EN2 = 1) (18)
Fault Condition Time-Out (18)
(18)
ns
ns
tPD
VINV < 0.8 V to VSW > 90% of High Level or VINV > 0.8 V to VSW < 10%
of Low Level
Retry Timer Cycle
–
tFALL
VIN = 5.0 V, ILOAD = 1.0 A
Buck Control Loop Propagation Delay
ns
tRISE
–
50
–
tSS
200
350
800
µs
tFAULT
–
10
–
ms
tRet
–
100
–
ms
OSCILLATOR
Oscillator Center Frequency(20)
RF = 11.3 kΩ
270
Oscillator Frequency Range
Oscillator Frequency Adjusting Resistor Range
Oscillator Frequency Adjustment
kHz
fOSC
(19), (20)
fOSC
200
RFREQ
7.0
330
400
kHz
–
22
kΩ
400
–
–
–
–
200
–
300
–
40
50
60
1.0
–
–
kHz
fOSC
RF = 7.0 kΩ
Oscillator Frequency Adjustment (19), (20)
300
kHz
fOSC
RF = 22 kΩ
Oscillator Default Frequency (Switching Frequency), FREQ Pin Open
fOSC
Oscillator Output Signal Duty Cycle (Square Wave, 180° Out-of-Phase with
the Internal Suitable Oscillator)
DOSC
Synchronization Pulse Minimum Duration (18)
tSYNC
kHz
%
µs
Notes
18. Design information only. This parameter is not production tested.
19. see Figure 4 for more details
20. RF = RFREQ resistor connected to the FREQ pin.
34702
12
Analog Integrated Circuit Device Data
Freescale Semiconductor
ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
Table 4. DYNAMIC ELECTRICAL CHARACTERISTICS (continued)
Characteristics noted under conditions -40°C ≤ TA ≤ 85°C unless otherwise noted. Input voltages VIN1 = VIN2 = 3.3 V using
the typical application circuit (see Figures 33) unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
tON
–
24
–
µs
tBST_PD
–
50
–
ns
–
5.0
–
3.0
tFAULT
8.0
10
12
ms
tRet
80
100
120
ms
Monitoring LFB Pin Delay
tD_RST_LFB
12
–
28
µs
Monitoring INV Pin Delay
tD_RST_INV
12
–
28
µs
SCL Clock Frequency (21)
fSCL
–
–
100
kHz
Bus Free Time Between a STOP and a START Condition (21)
tBUF
4.7
–
–
µs
4.0
–
–
BOOST REGULATOR
Boost Regulator MOSFET Maximum ON Time (21)
Boost Regulator Control Loop Propagation Delay (21)
Boost Switching Node VBD Rise Time
(21)
Boost Switching Node VBD Fall Time (21)
ns
tB_RISE
IBST = 20 mA
ns
tB_FALL
IBST = 20 mA
LINEAR REGULATOR (LDO)
Fault Condition Time-Out
Retry Timer Cycle
Reset Monitor (RST)
SCA, SCL PIN, I2C BUS (STANDARD)
Hold Time (Repeated) START Condition (After this period, the first clock
µs
tHD-STA
pulse is generated.) (21)
Low Period of the SCL Clock (21)
tLOW
4.7
–
–
µs
High Period of the SCL Clock (21)
tHIGH
4.0
–
–
µs
–
–
250
SDA Fall Time from VIH_MAX to VIL_MIN, Bus Capacitance 10 pF to 400
tF
pF, 3.0 mA Sink Current (21), (23)
ns
Setup Time for a Repeated START Condition (21)
tSU-STA
4.7
–
–
µs
Data Hold Time for I2C Bus Devices (21), (22)
tHD-DAT
0.0
–
–
µs
Data Setup Time (21)
tSU-DAT
250
–
–
ns
Setup Time for STOP Condition (21)
tSU-STO
4.0
–
–
µs
CB
–
–
400
pF
Capacitive Load for Each Bus Line (21)
Notes
21. Design information only. This parameter is not production tested.
22. The device provides an internal hold time of at least 300 ns for the SDA signal (refer to the VIH_MIN of the SCL signal) to bridge the
undefined region of the falling edge of SCL.
23. VIH = High level voltage on I²C bus and VIL = Low level voltage on I²C bus
34702
Analog Integrated Circuit Device Data
Freescale Semiconductor
13
ELECTRICAL CHARACTERISTICS
TIMING DIAGRAM
TIMING DIAGRAM
tHD-STA
tHD-STA
tSU-STO
tSU-STA
tSU-DAT
tHD-DAT
Note: Refer to the latest I2C bus specification for further details.
Figure 4. Definition of Time on the I2C Bus
ELECTRICAL PERFORMANCE CURVES
fOSC
(kHz) (kHz)
Oscillator
frequency
fOSC
(kHz)
fOSC
(kHz)
Fosc
Fosc
(kHz)
(kHz)
300
300
295
295
290
290
285
285
280
280
-50
-50
0
50
0
50
Temperature
(°C)
Temperature
(°C)
Temperature
(C°)
Figure 5. fOSC vs. Temperature
100
100
450
400
350
300
250
200
150
100
7
12
17
22
Rf(k
(kOhm
Rf
Ω) )
Figure 6. fOSC vs. Rf
34702
14
Analog Integrated Circuit Device Data
Freescale Semiconductor
0.83
100
90
80
70
60
50
40
30
20
10
0
0.82
Vin=3.3V,
Vin=3.3V,
Vin=5.0V,
Vin=5.0V,
VREF
Vref(V)
(V)
Switcher Efficiency [%]
ELECTRICAL CHARACTERISTICS
ELECTRICAL PERFORMANCE CURVES
Vout=1.2V
Vout=1.8V
Vout=1.2V
Vout=1.8V
0.81
0.80
0.79
0.78
0.77
-50
0
0.5
1
1.5
2
2.5
3
3.5
0
50
100
TTemperature
e m p e r atu r e(C°)
(°C)
Load Current [A]
Figure 7. Switcher Efficiency vs. Load Current
5.00
4.75
4.50
4.25
4.00
3.75
3.50
3.25
3.00
Timer (ms)
Switcher I LIM (A)
Figure 9. VREF vs. Temperature
-50
0
50
Temperature (C°)
Figure 8. Switcher ILIM vs. Temperature
100
25
23
21
19
17
15
13
11
9
7
5
0
100
200
300
RT (kOhm) with CT = 33nF
RT (k Ω) with CT = 33 nF
Figure 10. Timer (ms) vs. RT
34702
Analog Integrated Circuit Device Data
Freescale Semiconductor
15
FUNCTIONAL DESCRIPTION
INTRODUCTION
FUNCTIONAL DESCRIPTION
INTRODUCTION
The 34702 power supply integrated circuit provides the
means to efficiently supply the Freescale Power QUICC and
other families of Freescale microprocessors. It incorporates a
high-performance synchronous buck regulator, supplying the
microprocessor’s core, and a low dropout (LDO) linear
regulator providing the microprocessor I/O and bus voltages.
This device incorporates many advanced features; e.g.,
precisely maintained up/down power sequencing, ensuring
the proper operation and protection of the CPU and power
system. At the same time, it provides high flexibility of
configuration, allowing the maximum optimization of the
power supply system.
FUNCTIONAL PIN DESCRIPTION
OSCILLATOR FREQUENCY PIN (FREQ)
This switcher frequency selection pin can be adjusted by
connecting external resistor RF to the FREQ pin. The default
switching frequency (FREQ pin left open or tied to VDDI) is
set to 300 kHz.
BOOTSTRAP PIN (BOOT)
Bootstrap capacitor input.
SERIAL DATA PIN (SDA)
I2C bus pin. Serial data.
INVERTING INPUT PIN (INV)
Buck Controller Error Amplifier inverting input.
OUTPUT VOLTAGE PIN (VOUT)
Output voltage of the buck converter. Input pin of the
switching regulator power sequence control circuit.
SERIAL CLOCK PIN (SCL)
I2C bus pin. Serial clock.
LINEAR COMPENSATION PIN (LCMP)
Linear regulator compensation pin.
INPUT VOLTAGE 2 PINS (VIN2)
Buck regulator power input. Drain of the high-side power
MOSFET.
SWITCH PINS (SW)
Buck regulator switching node. This pin is connected to the
inductor.
GROUND PINS (GND)
Analog ground of the IC, thermal heatsinking.
POWER GROUND PINS (PGND)
Buck regulator power ground.
BOOST DRAIN PIN (VBD)
Drain of the internal boost regulator power MOSFET.
BOOST VOLTAGE PIN (VBST)
Internal boost regulator output voltage. The internal boost
regulator provides a 20 mA output current to supply the drive
circuits for the integrated power MOSFETs and the external
N-channel power MOSFET of the linear regulator. The
voltage at the VBST pin is 7.75V nominal.
LINEAR FEEDBACK PIN (LFB)
Linear regulator feedback pin.
LINEAR REGULATOR PIN (LDO)
Input pin of the linear regulator power sequence control
circuit.
CURRENT SENSE PIN (CS)
Current sense pin of the LDO. Overcurrent protection of
the linear regulator external power MOSFET. The voltage
drop over the LDO current sense resistor RS is sensed
between the CS and LDO pins. The LDO current limit can be
adjusted by selecting the proper value of the current sensing
resistor RS.
LINEAR DRIVE PIN (LDRV)
LDO gate drive of the external pass N-channel MOSFET.
INPUT VOLTAGE 1 PIN (VIN1)
The input supply pin for the integrated circuit. The internal
circuits of the IC are supplied through this pin.
34702
16
Analog Integrated Circuit Device Data
Freescale Semiconductor
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
POWER SUPPLY PIN (VDDI)
RESET TIMER PIN (RT)
Internal supply voltage. A ceramic low ESR 1uF 6V X5R or
X7R capacitor is recommended.
The Reset Timer power-up delay (RT) pin is used to set
the delay between the time when the LDO and switcher
outputs are active and stable and the RST output is released.
An external resistor and capacitor are used to program the
timer. The power-up delay can be obtained by using the
following formula:
t D = 10 ms + R tC t
Where R t is the Reset Timer programming resistor and C t
is the Reset Timer programming capacitor, both connected in
parallel from RT to ground.
Note Observe the maximum C t value and expect reduced
accuracy if R t is less than 10 kΩ.
ADDRESS PIN (ADDR)
The ADDR pin is used to set the address of the device
when used in an I2C communication. This pin can either be
tied to VDDI or grounded through a 10 kΩ resistor. Refer to
I2C Bus Operation on page 26 for more information on this
pin.
ENABLE 1 AND 2 PINS (EN1 AND EN2)
These two pins permit positive logic control of the Enable
function and selection of the Power Sequencing mode
concurrently. Table 5 depicts the EN1 and EN2 function and
Power Sequencing mode selection.
Both EN1 and EN2 pins have internal pull-down resistors
and both can withstand a short circuit to the supply voltage,
6.0 V.
Table 5.
Operating Mode Selection
EN1
EN2
Operating Mode
0
0
Regulators Disabled
0
1
Standard Power Sequencing
1
0
Inverted Power Sequencing
1
1
No Power Sequencing,
Regulators Enabled
RESET OUTPUT PIN (RST)
The Reset Control circuit monitors both the switching
regulator and the LDO feedback voltages. It is an open drain
output and has to be pulled up to some supply voltage (e.g.,
the output of the LDO) by an external resistor.
The Reset Control circuit supervises both output
voltages—the linear regulator output VLDO and the switching
regulator output VOUT. When either of these two regulators
is out of regulation (high or low), the RST pin is pulled low.
There is a 20 µs delay filter preventing erroneous resets.
During power-up sequencing, RST is held low until the Reset
Timer times out.
CLOCK SELECTION PIN (CLKSEL)
This pin sets the CLKSYN pin as either an oscillator output
or a synchronization input pin. The CLKSEL pin is also used
for the I2C address selection.
CLOCK SYNCHRONIZATION PIN (CLKSYN)
Oscillator output/synchronization input pin.
34702
Analog Integrated Circuit Device Data
Freescale Semiconductor
17
FUNCTIONAL DESCRIPTION
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
INTRODUCTION
The 34702 incorporates a high-performance synchronous
buck regulator, supplying the microprocessor’s core, and a
low dropout (LDO) linear regulator providing the
microprocessor I / O and bus voltages. This device
incorporates many advanced features; e.g., precisely
maintained up / down power sequencing, ensuring the proper
operation and protection of the CPU and power system.
Boost Regulator
Power Sequencing
Voltage Margining
Watchdog Timer
UVLO
Buck Control Logic
I2C Interface
Reset Control
POR Timer
Buck HS and
LS Driver
VDDI
Internal
Supply
Bandgap
Bandgap
Voltage
Voltage
Reference
Reference
Switcher
Oscillator
300 kHz
Linear Regulator
Control
ILIM
Thermal Shutdown
Figure 11. 34702 Functional Internal Block Diagram
BOOST REGULATOR
A boost regulator provides a high voltage necessary to
properly drive the buck regulator power MOSFETs,
especially during the low input voltage condition. The LDO
regulator external N-channel MOSFET gate is also powered
from the boost regulator. In order to properly enhance the
high-side MOSFETs when only a +3.3 V supply rail powers
the integrated circuit, the boost regulator provides an output
voltage of 7.75 V nominal value.
The 34702 boost regulator uses a simple hysteretic
current control technique, which allows fast power-up and
does not require any compensation. When the boost
regulator main power switch (low side) is turned on, the
current in the inductor starts to ramp up. After the inductor
current reaches the upper current limit (nominally set at
1.0 A), the low-side switch is turned off and the current
charges the output capacitor through the internal rectifier.
When the inductor current falls below the valley current limit
value (nominally 600 mA), the low-side switch is turned on
again, starting the next switching cycle. After the boost
regulator output capacitor reaches approximately 6.0 volts,
the peak and valley current limit levels are proportionally
scaled down to approximately one fifth of their original values.
When the boost regulator reaches its regulation limit (7.75 V
typical), the low-side switch is turned off until the output
voltage falls below the regulation limit again.
The higher current limit values in the beginning of the
boost regulator start-up sequence allow fast power up of the
whole IC, while the normal operation with reduced current
limit greatly reduces the switching noise and therefore
improves the overall EMC performance. See Figure 12 for
the boost regulator output voltage and inductor current
waveforms (picture not to scale).
34702
18
Analog Integrated Circuit Device Data
Freescale Semiconductor
FUNCTIONAL DESCRIPTION
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
7.75V
Booster Output Voltage
Fault Timer
t FAULT = 10 ms
t FAULT = 10 ms
I pk Cu rrent Limit
Ip k
6.0 V
0.5 I pk
0.5 Ipk
Retry Timer
t Ret = 10 0 ms
0A
0V
Ipk = 1 A typ.
Booster Inductor Current
0.6 A typ.
0.2 A typ.
0.1 A typ.
Figure 12. Boost Regulator Startup (Not To Scale)
SWITCHING REGULATOR
The switching regulator is a high-frequency (300 kHz
default, adjustable in the range from 200 kHz to 400 kHz),
synchronous buck converter driving integrated high-side and
low-side N-channel power MOSFETs. The switching
regulator output voltage is adjustable by means of an external
resistor divider to provide the required output voltage within
±2.0% accuracy, and is intended to directly power the core of
the microprocessor. The buck controller uses a PWM Voltage
Mode Control topology with Feed-Forward to achieve
excellent line and load regulation.
The 34702 integrated boost regulator provides a 7.75 V
rail which is used to properly bias the switcher’s MOSFET. In
addition, the boost structure has a very low start up voltage
(Typically 1.6 V), hence ensuring very low input voltage
functionality. A typical bootstrap technique is used to provide
voltage necessary to properly enhance the high-side
MOSFET gate. When the regulator is supplied only from lowinput voltage (e.g., single +3.3 V supply rail), the bootstrap
capacitor is charged from the internal boost regulator output
VBST through an external diode. This arrangement allows
the 34702 to operate from very low input voltage and also
comply with the power sequencing requirements of the
supplied microcontroller.
Figure 13. Switching Regulator Current Limit
(Not To Scale)
To avoid destruction of the supplied circuits, the switching
regulator has a current limit with retry capability. When an
overcurrent condition occurs and the switch current reaches
the peak current limit value, the main (high-side) switch is
turned off until the inductor current decays to the valley value,
which is one-half of the peak current limit. If an overcurrent
condition exists for 10 ms, the buck regulator control circuit
shuts the switcher OFF and the switcher retry timer starts to
time out. When the timer expires after 100 ms, the switcher
engages the start-up sequence and runs for 10 ms,
repeatedly checking for the overcurrent condition. Figure 13
describes the switching regulator overcurrent condition and
current limit. During the current limited operation (e.g., in
case of short circuit on the switching regulator output), the
switching regulator operation is not synchronized to the
oscillator frequency. Figure 14 (respectively Figure 15)
depicts the current limit with a retry capability feature of the
switcher (respectively LDO).
Figure 14. Switching Converter Overcurrent Protection
34702
Analog Integrated Circuit Device Data
Freescale Semiconductor
19
FUNCTIONAL DESCRIPTION
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
100 ms, the LDO tries to power up again for 10 ms,
repeatedly checking for the overcurrent condition. The
current limit of the LDO can be set by using the following
formula:
ILIM = 50 mV / RS
Figure 15. LDO Converter Overcurrent Protection
The output voltage VOUT can be adjusted by means of an
external resistor divider connected to the feedback control
pin INV. The switching regulator output voltage can be
adjusted in the range of 0.8 V to VIN - buck dropout voltage.
Power-up, power-down, and fault management are
coordinated with the linear regulator.
SWITCHER OSCILLATOR
A 300 kHz (default) oscillator sets the switching frequency
of the buck regulator. The frequency of the oscillator can be
adjusted between 200 kHz and 400 kHz by an optional
external resistor RF connected from the FREQ pin of the
integrated circuit to ground. See Figure 6 on page 14 for
frequency resistor selection.
The CLKSYN pin can be configured as either an oscillator
output when the CLKSEL pin is left open or as a
synchronization input when the CLKSEL pin is grounded.
The oscillator output signal is a square wave logic signal with
50% duty cycle, 180 degrees out-of-phase with the internal
clock signal. This allows opposite phase synchronization of
two 34702 devices.
When the CLKSYN pin is used as a synchronization input
(CLKSEL pin grounded), the external resistor RF chosen
from the chart in Figure 6 should be used to synchronize the
internal slope compensation ramp to the external clock.
Operation is only recommended between 200 kHz and
400 kHz. The supplied synchronization signal does not need
to be 50% duty cycle. Minimum pulse width is 1.0 µs.
LOW DROPOUT LINEAR REGULATOR (LDO)
The adjustable low dropout linear regulator (LDO) is
capable of supplying a 1.0 A output current. It has a current
limit with retry capability. When the voltage measured across
the current sense resistor reaches the 50 mV threshold, the
control circuit limits the current for 10 ms. If the overcurrent
condition still exists, the linear regulator is turned off and the
retry timer starts to time out. When the timer expires after
Where RS is the LDO current sense resistor, connected
between the CS pin and the LDO pin output (see Figure 33
on page 34), and 50 mV is the typical value of the LDO
current sense comparator threshold voltage.
When no current sense resistor is used, it is still possible
to detect the overcurrent condition by tying the current sense
pin CS to the VBST voltage. In this case, the overcurrent
condition is sensed by saturation of the linear regulator driver
buffer.
The output voltage of the LDO can be adjusted by means
of an external resistor divider connected to the feedback
control pin LFB. The linear regulator output voltage can be
adjusted in the range of 0.8 V to VIN - LDO dropout voltage.
Power-up, power-down, and fault management are
coordinated with the switching regulator.
POWER SEQUENCING VOLTAGE MARGINING
WATCHDOG TIMER
A watchdog function is available via I2C bus
communication. It is possible to select either window
watchdog or time-out watchdog operation, as illustrated in
Figure 16.
Watchdog time-out starts when the watchdog function is
activated via I2C bus sending a Watchdog Programming
command byte, thus determining watchdog operation
(window or time-out) and period duration (refer to Table 8,
page 27). If the watchdog is cleared by receiving a new
Watchdog Programming command through the I2C bus, the
watchdog timer is reset and the new time-out period begins.
If the watchdog time expires, the RST will become active
(LOW) for a time determined by the RC components of the
RT timer plus 10 ms. After a watchdog time-out, the function
is no longer active.
Watchdog Closed
No Watchdog Clear Allowed
Window Open
for Watchdog Clear
50% of Watchdog Period
Watchdog Period
Timing Selected via 12C Bus – See Table 4
Window Watchdog
Window Open for Watchdog Clear
Watchdog Period
Timing Selected via I2C Bus – See Table 4
Time-Out Watchdog
Figure 16. Watchdog Operation
34702
20
Analog Integrated Circuit Device Data
Freescale Semiconductor
FUNCTIONAL DESCRIPTION
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
When the Window Watchdog function is selected, the
timer cannot be cleared during the Closed Window time,
which is 50% of the total watchdog period. When the
watchdog is cleared, the timer is reset and starts a new timeout period. If the watchdog is not cleared during the Open
Window time, the RST will become active (LOW) for a time
determined by the RC components of the RT timer plus
10 ms.
34702
Analog Integrated Circuit Device Data
Freescale Semiconductor
21
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
THERMAL SHUTDOWN
POWER SEQUENCING MODES
To increase the overall safety of the system designed with
the 34702, an internal thermal shutdown function has been
incorporated into the switching regulator circuit. The 34702
senses the temperature of the buck regulator main switching
MOSFET (high-side MOSFET M1; see Figure 2 on page 2),
the low-side (synchronous MOSFET M2), and control circuit.
If the temperature of any of the monitored components
exceeds the limit of safe operation (thermal shutdown), the
switching regulator and the LDO shut down. After the
temperature falls below the value given by the thermal
shutdown hysteresis window, the switcher tries again to
operate.
The VOUT pull-down MOSFET M3 has an independent
thermal shutdown control. If the M3 temperature exceeds the
thermal shutdown limit, the M3 is turned off without affecting
the switcher operation.
The power sequencing of the two outputs of this power
supply IC is in compliance with the Freescale Power QUICC
and other 32-bit microprocessor requirements. When the
input voltage is applied, the switcher and linear regulator
outputs follow the supply rail voltage during power-up and
power-down in the limits given by the microcontroller power
sequencing specification, illustrated in Figures 17 through
19. There are two possible power sequencing modes,
Standard and Inverted, as explained in more detail below.
The third mode of operation is Power Sequencing Disabled.
3.3 V Input
2.5 V
34702
VIN2
VIN1
VBD
VBST
LDRV
CS
The LDO pull-down MOSFET M4 has an independent
thermal shutdown control. If the M4 temperature exceeds the
thermal shutdown limit, the M4 will be turned off without
affecting the LDO operation.
ADDR
SOFT START
SDA
SCL
GND
RT
A switching regulator soft start feature is incorporated in
the 34702. The soft start is active each time the IC is enabled,
VIN is reapplied, or after a fault retry. Other transient events
do not activate the soft start.
EN1
EN2
CLKSYN
CLKSEL
FREQ
Optional
VDDL (Core)
LFB
MCU
RST
BOOT
VBST
1.5 V
VDDH (I/Os)
SW
VOUT
PGND
INV
VDDI
VOLTAGE MARGINING
The 34702 includes a voltage margining feature accessed
through the I2C bus. Voltage margining allows for
independent adjustment of the Switcher VOUT voltage and
the linear output VLDO. Each can be adjusted up and down
in 1.0% steps to a range of ±7.0%. This feature allows for
worst case system validation; i.e., determining the design
margin. Margining details are described in the section entitled
I2C Bus Operation, beginning on page 26 of this datasheet.
3.3 V
LDO
Other
Circuits
3.3 V Input Supply (I/O Voltage)
1.8V Start-Up
Slope
1.0 V/ms
(typ.)
∆V = 2.1 V
Max. Lead
1.5 V Core Voltage
∆V = 2.1 V
Max. Lead
∆V = 0.4 V
Max. Lag
Figure 17. Standard Power Up / Down Sequence
in +3.3 V Supply System
34702
22
Analog Integrated Circuit Device Data
Freescale Semiconductor
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
5.0 V Input
5.0 V Input
34702
34702
VIN2
VIN1
VBD
VBST
LDRV
CS
Optional
VIN1
VBD
VBST
LDRV
CS
ADDR
SDA
SCL
GND
RST
SDA
SCL
GND
EN1
BOOT
MCU
EN2
CLKSYN
VOUT
CLKSEL
PGND
FREQ
VBST
5.0 V
1.5 V
VDDL (Core)
SW
Optional
INV
MCU
EN1
EN2
BOOT
CLKSYN
VOUT
CLKSEL
PGND
VBST
SW
FREQ
3.3 V
VDDH (I/Os)
INV
5.0 V Input Supply
3.3 V I/O Voltage (VOUT)
5.0 V Input Supply
∆V = 2.1 V
Max. Lead
3.3 V I/O Voltage (VLDO)
1.5 V Core Voltage
∆V = 0.4 V
Max. Lag
LFB
VDDI
∆V = 2.1 V
Max. Lead
1.8V Start-Up
VDDL (Core)
RST
VDDI
∆V = 2.1 V
Max. Lead
1.5 V
LDO
RT
VDDH (I/Os)
LFB
ADDR
5.0 V
3.3 V
LDO
RT
VIN2
(VOUT)
∆V = 0.4 V
Max. Lag
Figure 18. Standard Power Up / Down Sequence
in +5.0 V Supply System
STANDARD POWER SEQUENCING
When the power supply IC operates in the Standard Power
Sequencing mode, the switcher output provides the core
voltage for the microprocessor. This situation and operating
conditions are illustrated in Figures 17 and 18. Table 5,
page 17, shows the Power Sequencing mode selection.
INVERTED POWER SEQUENCING
When the power supply IC is operating in the Inverted
Power Sequencing mode, the linear regulator (LDO) output
provides the core voltage for the microprocessor, as
illustrated in Figure 19. Table 5 shows the Power
Sequencing mode selection.
1.8V Start-Up
∆V = 2.1 V
Max. Lead
1.5 V Core Voltage (VLDO)
∆V = 0.4 V
Max. Lag
∆V = 0.4 V
Max. Lag
Figure 19. Inverted Power Up / Down Sequence in +5.0 V
Supply System
ASSUMED REQUIREMENTS
1. I/O supply voltage not to exceed core voltage by more
than 2.0 V.
2. Core supply voltage not to exceed I/O voltage by more
than 0.4 V.
Methods of Control
The 34702 has several methods of monitoring and
controlling the regulator output voltages, as described in the
paragraphs below. Power sequencing control is also
achieved through the intrinsic operation of the regulators.
The EN1 and EN2 pins can be used to select the proper
power sequencing mode required by the powered system or
to disable the power sequencing (refer to Table 5).
Intrinsic Operation
For both the LDO and switcher, whenever the output
voltage is below the regulation point, the LDO external Pass
MOSFET is on, or the Buck High-Side MOSFET is on at a
duty cycle controlled by the switcher. Because these devices
are MOSFETs, current can flow in either direction, balancing
the voltages via the common supply pin. The ability to
maintain the MOSFETs on is dependent on the available gate
voltage, and thus the size of the boost regulator storage
capacitor.
34702
Analog Integrated Circuit Device Data
Freescale Semiconductor
23
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
Standard Power Sequencing Control
Comparators monitor voltage differences between the
LDO (LDO pin) and the switcher (VOUT pin) outputs as
follows:
1. LDO > VOUT + 1.9 V, turn off LDO. The LDO can be
forced off. This occurs whenever the LDO output
voltage exceeds the switcher output voltage by more
than 1.9 V.
2. LDO > VOUT + 2.0 V, shunt LDO to ground. If turning
off the LDO is insufficient and the LDO output voltage
exceeds the switcher output voltage by more than
2.0 V, a 1.5 Ω shunt MOSFET is turned on that
discharges the LDO load capacitor to ground. The
shunt MOSFET is used for switcher output shorts to
ground and for power down in case of VIN1 ≠ VIN2
with the switcher output falling faster than the LDO.
3. LDO < VOUT + 1.9 V cancel (2).
VOUT output voltage is less than 1.8 V above the LDO
output voltage.
4. VOUT < LDO + 2.0 V, cancel (2)
5. VOUT < LDO - 0.2 V, turn off LDO. The LDO can be
forced off. This occurs whenever the VOUT is less than
VLDO - 0.2 V.
6. VOUT < LDO - 0.3 V, turn on the 1.5 Ω LDO sink
MOSFET. This occurs when the LDO output voltage
exceeds the VOUT output by more than 300 mV.
7. VOUT < LDO - 0.2 V, cancel (6).
8. VOUT < LDO - 0.1 V, cancel (5). Normal operation
resumes when VOUT > LDO - 0.1 V.
STANDARD OPERATING MODE
Single 3.3 V Supply, VIN = VIN1 = VIN2 = 3.3 V
4. LDO < VOUT + 1.8 V, cancel (1) above, re-enable
LDO. Normal operation resumes when the LDO output
voltage is less than 1.8 V above the switcher output
voltage.
The 3.3 V supplies the microprocessor I/O voltage, the
switcher supplies core voltage (e.g., 1.5 V nominal), and the
LDO operates independently (see Figure 17, page 22).
Power sequencing depends only on the normal switcher
intrinsic operation to control the Buck High-Side MOSFET.
5. LDO < VOUT - 0.1 V, turn off switcher. The switcher
can be forced off. This occurs whenever the LDO is
less than VOUT - 0.1 V.
Power-Up
6. LDO < VOUT - 0.3 V, turn on Sync (LS) MOSFET and
1.5 Ω VOUT sink MOSFET. The Buck High-Side
MOSFET is forced off and the Sync MOSFET is forced
on. This occurs when the switcher output voltage
exceeds the LDO output by more than 300 mV.
When VIN is rising, initially VOUT is below the regulation
point and the Buck High-Side MOSFET is on. In order not to
exceed the 2.1 V differential requirement between the I/O
(VIN) and the core (VOUT), the switcher must start up at
2.1 V or less and be able to maintain the 2.1 V or less
differential. The maximum slew rate for VIN is 1.0 V/ms.
7. LDO > VOUT - 0.3 V, cancel (6).
8. LDO > VOUT - 0.1 V, cancel (5). Normal operation
resumes when LDO < VOUT - 0.1 V.
Inverted Power Sequencing Control
Comparators monitor voltage differences between the
switcher (VOUT pin) and LDO (LDO pin) outputs as follows:
1. VOUT > LDO + 1.8 V, turn off VOUT . The switcher
VOUT can be forced off. This occurs whenever the
VOUT output voltage exceeds the LDO output voltage
by more than 1.8 V.
2. VOUT > LDO + 2.0 V, shunt VOUT to ground. If turning
off the switcher VOUT is insufficient and the VOUT
output voltage exceeds the LDO output voltage by
more than 2.0 V, a 1.5 Ω shunt MOSFET and the
switcher synchronous MOSFET are turned on to
discharge the VOUT load capacitor to ground. The
shunt MOSFET and synchronous MOSFET are used
for LDO output shorts to ground and for power-down in
case of VIN1 ≠ VIN2 with LDO output falling faster than
the VOUT .
3. VOUT < LDO + 1.8 V, cancel (1) and (2) above, reenable VOUT . Normal operation resumes when the
Power-Down
When VIN is falling, VOUT falls below the regulation point;
therefore, the Buck High-Side MOSFET is on. In the case
where VOUT is falling faster than VIN, the Buck High-Side
MOSFET attempts to maintain VOUT. In the case where VIN
is falling faster than VOUT, the Buck High-Side MOSFET is
also on, and the VOUT load capacitor is discharged through
the Buck High-Side MOSFET to VIN. Thus, provided VIN
does not fall too fast, the core voltage (VOUT) does not
exceed the I/O voltage (VIN) by more than a maximum of
0.4 V.
Shorted Load
1. VOUT shorted to ground. This causes the I/O voltage
to exceed the core voltage by more than 2.1 V. No load
protection.
2. VIN shorted to ground. Until the switcher load
capacitance is discharged, the core voltage exceeds
the I/O voltage by more than 0.4 V. By the intrinsic
operation of the switcher, the load capacitor is
discharged rapidly through the Buck High-Side
MOSFET to VIN.
3. VOUT shorted to supply. No load protection. 34702 is
protected by current limit and thermal shutdown.
34702
24
Analog Integrated Circuit Device Data
Freescale Semiconductor
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
Single 5.0 V Supply, VIN1 = VIN2, or Dual Supply VIN1 ≠
VIN2
The LDO supplies the microprocessor I/O voltage. The
switcher supplies the core (e.g., 1.5 V nominal) (see
Figure 18, page 23).
Power-Up
This condition depends upon the regulator current limit,
load current and capacitance, and the relative rise times of
the VIN1 and VIN2 supplies. There are two cases:
1. LDO rises faster than VOUT . The LDO uses control
methods (1) and (2) described in the section Methods
of Control on page 23.
2. VOUT rises faster than LDO. The switcher uses control
methods (5) and (6) described in the section Methods
of Control on page 23.
Power-Down
This condition depends upon the regulator load current
and capacitance and the relative fall times of the VIN1 and
VIN2 supplies. There are two cases:
1. VOUT falls faster than LDO. The LDO uses control
methods (1) and (2) described in the section Methods
of Control on page 23.
In the case VIN1 = VIN2, the intrinsic operation turns
on both the Buck High-Side MOSFET and the LDO
external Pass MOSFET, and discharges the LDO load
capacitor into the VIN supply.
2. LDO falls faster than VOUT . The switcher uses control
methods (5) and (6) described in the section Methods
of Control on page 23.
Shorted Load
1. VOUT shorted to ground. The LDO uses method (1)
and (2) described in the section Methods of Control on
page 23.
2. LDO shorted to ground. The switcher uses control
methods (5) and (6) described in the section Methods
of Control on page 23.
3. VIN1 shorted to ground. Device is not working.
4. VIN2 shorted to ground with VIN1 and VIN2 different.
This is equivalent to the switcher output shorted to
ground.
5. VOUT shorted to supply. No load protection. 34702 is
protected by current limit and thermal shutdown.
6. LDO shorted to supply. No load protection. 34702 is
protected by current limit and thermal shutdown.
INVERTED OPERATING MODE
Single 3.3 V Supply, VIN = VIN1 = VIN2 = 3.3 V
The 3.3 V supplies the microprocessor I/O voltage, the
LDO supplies core voltage (e.g., 1.5 V nominal), and the
switcher VOUT operates independently. Power sequencing
depends only on the normal LDO intrinsic operation to control
the Pass MOSFET.
Power-Up
When VIN is rising, initially LDO is below the regulation
point and the Pass MOSFET is on. In order not to exceed the
2.1 V differential requirement between the I/O (VIN) and the
core (LDO), the LDO must start up at 2.1 V or less and be
able to maintain the 2.1 V or less differential. The maximum
slew rate for VIN is 1.0 V/ms.
Power-Down
When VIN is falling, LDO falls below the regulation point;
therefore, the Pass MOSFET is on. In the case where LDO is
falling faster than VIN, the Pass MOSFET attempts to
maintain LDO. In the case where VIN is falling faster than
LDO, the Pass MOSFET is also on, and the LDO load
capacitor is discharged through the Pass MOSFET to VIN.
Thus, provided VIN does not fall too fast, the core voltage
(LDO) does not exceed the I/O voltage (VIN) by more than
maximum of 0.4 V.
Shorted Load
1. LDO shorted to ground. This will cause the I/O voltage
to exceed the core voltage by more than 2.1 V. No load
protection.
2. VIN shorted to ground. Until the LDO load capacitance
is discharged, the core voltage exceeds the I/O voltage
by more than 0.4 V. By the intrinsic operation of the
LDO, the load capacitor is discharged rapidly through
the Pass MOSFET to VIN.
3. LDO shorted to supply. No load protection.
Single 5.0 V Supply, VIN1 = VIN2, or Dual Supply VIN1 ≠
VIN2
The switcher VOUT supplies the microprocessor I/O
voltage. The LDO supplies the core (e.g., 1.5 V nominal) (see
Figure 19, page 23).
Power-Up
This condition depends upon the regulator current limit,
load current and capacitance, and the relative rise times of
the VIN1 and VIN2 supplies. There are two cases:
1. VOUT rises faster than LDO. The switcher VOUT uses
control methods (1) and (2) described in the section
Methods of Control on page 23.
2. LDO rises faster than VOUT . The LDO uses control
methods (5) and (6) described in the section Methods
of Control on page 23.
Power-Down
This condition depends upon the regulator load current
and capacitance and the relative fall times of the VIN1 and
VIN2 supplies. There are two cases:
34702
Analog Integrated Circuit Device Data
Freescale Semiconductor
25
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
1. LDO falls faster than VOUT . The VOUT uses control
methods (4) and (5) described in the section Methods
of Control on page 23.
In the case VIN1 = VIN2, the intrinsic operation turns
on both the Buck High-Side MOSFET and the LDO
external Pass MOSFET, and discharges the VOUT
load capacitor into the VIN supply.
2. VOUT falls faster than LDO. The LDO uses control
methods (5) and (6) described in the section Methods
of Control on page 23.
Shorted Load
1. LDO shorted to ground. The VOUT uses methods (1)
and (2) described in the section Methods of Control on
page 23.
2. VOUT shorted to ground. The LDO uses control
methods (5) and (6) described in the section Methods
of Control on page 23.
3. VIN1 shorted to ground. Device is not working.
4. VIN2 shorted to ground. This is equivalent to the
switcher VOUT output shorted to ground.
5. LDO shorted to supply. No load protection. 34702 is
protected by current limit and thermal shutdown.
6. VOUT shorted to supply. No load protection. 34702 is
protected by current limit and thermal shutdown.
LOGIC COMMANDS AND REGISTERS
I2C BUS OPERATION
I2C
The 34702 device is compatible with the
interface
standard. SDA and SCL pins are the Serial Data and Serial
Clock pins of the I2C bus.
assure its unique address. Figure 21 illustrates the flexible
addressing feature for a 7-bit address. Table 6 provides the
definition of the selectable portion of the device address.
When the ADDR pin is used and put to low level, pull the
ADDR pin to ground through a 10 kΩ resistor.
I2C COMMAND AND DATA FORMATS
Communication starts with a START condition, followed by
the slave device unique address. The Read/Write (R/W) bit
defines whether the data should be read from or written to the
device (the 34702 operates only as a slave device; therefore,
the R/W bit should always be set to 0). The 34702 responds
by sending the Acknowledge bit (Ack) to the master device.
Figure 20 illustrates the beginning of an I2C communication
for a 7-bit slave address.
S
7-Bit Address
Bits
MSB
Communication Start
R/W
5
4
3
2
1
1
1
0
1 A1 A0
1
0
Figure 21. Address Bit Definition for 7-Bit Address
Table 6.
Definition of Selectable Portion of Device
Address
CLKSEL Pin
ADDR Pin
A1
A0
Low
Low
0
0
Low
High (Open)
0
1
High (Open)
Low
1
0
High (Open)
High (Open)
1
1
Figure 20. Communication Start Using 7-Bit Address
34702 has the two least significant address bits (LSB)
defined by the state of the CLKSEL pin (A1) and the ADDR
pin (A0).
Note The state of the CLKSEL pin also defines the
configuration of the oscillator synchronization CLKSYN pin.
Leaving the CLKSEL pin open or pulling it high defines the
CLKSYN pin as an oscillator output. When the CLKSEL pin
is pulled low, the CLKSYN pin is configured as a
synchronization input for the external clock signal.
This feature allows up to four 34702 ICs to communicate
in the same I2C bus, all of them sharing the same high-order
address bits. A different combination of the two LSB address
bits A1 and A0 can be assigned to each individual part to
6
Fixed Address Selectable
Address
Ack
Slave Address Definition
LSB
Writing Data Into the Slave Device
After the address acknowledgment by the slave, DATA
can be written into the slave registers. The R/W bit must be
set to 0 to allow DATA to be written into the 34702. Figure 22
shows the data write sequence. Actions performed by the
slave device are grayed.
S
7-Bit Address
0
Ack
DATA
Ack
(Write)
Figure 22. Data Transfer for Write Operations
34702
26
Analog Integrated Circuit Device Data
Freescale Semiconductor
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
DATA Definition
Table 8.
The DATA field in the single Data Transfer contains one or
several Command Bytes. The Command Byte identifies the
kind of operation required by the master to be performed and
has two fields, as illustrated in Figure 23:
Command Byte Definitions
Watchdog
Programming
(As a 2nd
Command Byte)
1. Address field
0
1
1
0
0
0
0
0
1st Command
0
1
1
0
0
0
0
0
WD OFF
(24)
0
1
1
0
1
0
0
0
WD 1280 ms
Wind. OFF
0
1
1
0
1
0
0
1
WD 320 ms
Wind. OFF
0
1
1
0
1
0
1
0
WD 80 ms
Wind. OFF
0
1
1
0
1
0
1
1
WD 20 ms
Wind. OFF
0
1
1
0
1
1
0
0
WD 1280 ms
Wind. ON
0
1
1
0
1
1
0
1
WD 320 ms
Wind. ON
0
1
1
0
1
1
1
0
WD 80 ms
Wind. ON
0
1
1
0
1
1
1
1
WD 20 ms
Wind. ON
2. Value field
The address field is selected from the list in Table 7.
Bits
MSB
7
6
5
4
LSB
3
2
1
0
D7 D6 D5 D4 D3 D2 D1 D0
Address Field
Value Field
Figure 23. Command Byte
Table 7.
Address Field Definitions
Address Field
Operation
Write
001
Voltage Margining
W
011
Watchdog
W
Refer to Table 8, page 27, which summarizes the value
field definitions for the entire set of operation options.
Notes
24. The Watchdog timer is turned ON automatically after
receiving any other valid command byte changing watchdog
time.
Table 8.
Security in Writing Commands
Command Byte Definitions
Operation
Address
Value
Action
To improve the security level, a so-called first command is
defined to initiate each write communications. The first
command identifies the operation, which is executed by the
following Command Byte.
A first command has the address field equal to the related
operation one, followed by a null value field (all zeros).
Table 9 summarizes first command definitions. The master
sends the first command before the Command Byte for the
intended operation.
Voltage Margining
0
0
1
0
0
0
0
0
1st Command
(As a 2nd
Command Byte)
0
0
1
x
0
0
0
0
Output
Nominal
0
0
1
x
0
0
0
1
+ 1.0%
0
0
1
x
0
0
1
0
+ 2.0%
0
0
1
x
0
0
1
1
+ 3.0%
0
0
1
x
0
1
0
0
+ 4.0%
LDO Output: x = 0
0
0
1
x
0
1
0
1
+ 5.0%
Switcher Output
x=1
0
0
1
x
0
1
1
0
+ 6.0%
0
0
1
x
0
1
1
1
+ 7.0%
0
0
1
x
1
0
0
0
- 1.0%
VOLTAGE MARGINING OPERATION
0
0
1
x
1
0
0
1
- 2.0%
0
0
1
x
1
0
1
0
- 3.0%
0
0
1
x
1
0
1
1
- 4.0%
0
0
1
x
1
1
0
0
- 5.0%
0
0
1
x
1
1
0
1
- 6.0%
After starting the communication in Writing mode, the
master sends the first command followed by the specific
Command Byte to set the required voltage margining for
either the LDO or the switcher (see Figure 24). To achieve a
simultaneous set for both LDO and switcher, two specific
commands must be issued in sequence after the first
command, one for each supply.
0
0
1
x
1
1
1
0
- 7.0%
Table 9.
First Command Definitions
First Command
Operation
001 00000
Voltage Margining
011 00000
Watchdog Programming
34702
Analog Integrated Circuit Device Data
Freescale Semiconductor
27
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
0 0 1 0 0 0 0 0 Ack 0 0 1 x x x x x
First Byte for Voltage Margining
Command Byte
Figure 24. Voltage Margining Programming
(One Supply Only)
Note: x bits, which set the voltage margining value are
defined in Table 8.
WATCHDOG PROGRAMMING OPERATION
For watchdog operation control, the master periodically
sends a watchdog first command followed by a command
byte selecting, or confirming, the watchdog period according
to the options listed in Table 8. See Figure 25 for the
watchdog timer programming command example.
The internal watchdog timer is turned ON by receiving a
valid Watchdog Programming command (after receiving the
Watchdog Programming First Command), and it is cleared
each time the next Watchdog Programming command is
written into the device, provided it arrives during the window
open time. Thus, the Watchdog Programming command
clears the timer and sets the new timing conditions at the
same time. The Watchdog Programming First Command
01100000 sent twice shuts the timer OFF, and the watchdog
function is disabled. Any other valid watchdog command
turns the timer ON again.
address acknowledge sent by 34702. I2C bus protocol
defines this circumstance as a master-transmitter and slavereceiver configuration.
Figure 27 illustrates a communication beginning with the
slave address, the first command for voltage margining, and
a third byte containing the address field 001 and the value
field 00101 corresponding with the LDO fifth setting (LDO
output voltage = +5% above its nominal value). If a
simultaneous setting for switcher is needed, a fourth byte
should be included before the STOP condition (P); for
instance, 001 11100 to set the switcher in its twelfth setting
(switcher output voltage = -5% below its nominal value) - see
Figure 28.
The example of data transfer setting the Watchdog timer is
shown in the Figure 26.
S A6 A5 A4 A3 A2 A1 A0 0 Ack
START
Write
Slave Address
0
1
1
0
0
0
0
0 Ack
First Command for Watchdog Programming
0
1
1
0
1
0
0
1 Ack P
STOP
Address Field Value Field:
Time-out WD = 320 ms
(Window OFF)
0 1 1 0 0 0 0 0 Ack 0 1 1 x x x x x
First Byte for Watchdog Programming Command Byte
Figure 25. Watchdog Timer Programming
Note: x bits, which set the watchdog timer value are
defined in Table 8, page 27.
Communication Stop
Only the master can terminate the data transfer by issuing
a STOP condition. The slave waits for this condition to
resume its initial state waiting for the next START condition
(see Figure 26).
Figure 26. Data Transfer Example - Watch Dog Timer
Setting.
S A6 A5 A4 A3 A2 A1 A0 0 Ack
START
Write
Slave Address
0
0
1
0
0
0
0
0 Ack
First Command for Voltage Margining
0
0
1
0
0
1
0
1 Ack P
STOP
COMPLETE DATA TRANSFER EXAMPLES
The master device controlling the I2C bus always starts
addressing a 34702 slave IC in writing mode (R/W = 0) to
enable it to write a Command Byte just after receiving the
Address Field Value Field = LDO
5th Setting
Figure 27. Data Transfer Example - LDO Voltage
Margining
34702
28
Analog Integrated Circuit Device Data
Freescale Semiconductor
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
S A6 A5 A4 A3 A2 A1 A0 0 Ack
START
Write
Slave Address
0
0
1
0
0
0
0
0 Ack
First Command for Voltage Margining
0
0
1
0
0
1
0
1 Ack
Address Field Value Field: LDO
VLDO = Nom. + 5%
0
0
1
1
1
1
0
0 Ack P
STOP
Address Field Value Field: Switcher
VOUT = Nom. - 5%
Figure 28. Data Transfer Example - LDO and Switcher
Voltage Margining
34702
Analog Integrated Circuit Device Data
Freescale Semiconductor
29
TYPICAL APPLICATIONS
TYPICAL APPLICATIONS
BUCK REGULATOR CONTROL CIRCUIT
The 34702 buck regulator utilizes a PWM Voltage Mode
topology with Feed-Forward to achieve an excellent line and
load regulation. The control circuit block diagram is shown in
Figure 29.
L
Figure 29. Buck Regulator Control Circuit
The integrated 40 pF capacitor CF charged through the
1
external resistor R4 provides the feed-forward ramp
f z ( c ) = --------------------------------------2πC2 ( R1 + R3 )
waveform, the amplitude of which is proportional to the input
voltage, thus providing the feed-forward function.
The Feed-Forward implemented by resistor R4 and
Figure 30 shows the Bode plot of the 34702 buck regulator
integrated capacitor CF creates a pole in the overall loop
control loop gain and phase versus frequency.
transfer function, the frequency of which can be calculated
The first double pole on the Bode plot is created by the
from the following formula.
buck regulator output L-C filter, and its frequency can be
calculated as:
V IN
1
f p ( FF ) = ---------------------------------------------------------------- × --------------------(
– V Ref )
V
2πR4C F
1
IN
1
------- × -------------------------------- + V m1
f LC = ---------------------f sw
R4C F
2π C O L
Where CO is the value of the buck output capacitor and L
is the inductance value of the output filter inductor L.
The frequency of the compensating zero can be calculated
as follows.
Where VRef is the buck regulator reference voltage
(VRef = 0.8 V typ.) at the INV pin,
VIN is the buck regulator input voltage,
Vm1 is the ramp generated by the internal ramp
generator (Vm1 = 0.5 V typ.).
34702
30
Analog Integrated Circuit Device Data
Freescale Semiconductor
TYPICAL APPLICATIONS
.
G ain
[dB]
20
1
R2 = V Ref × ----------------------------------------------------------------------------------------( V O + I O × R L ) – V Ref V O – V Ref
-------------------------------------------------------- + ------------------------R4
R1
fLC
fz(c)
Where VRef is the buck regulator reference voltage
(VRef = 0.8 V typ.) at the INV pin,
VO is the selected output voltage,
IO is the output load current,
RL is the DC resistance of the inductor L.
It is apparent that the buck regulator output voltage is
affected by the voltage drop caused by the inductor serial
resistance and the regulator output current. In those
applications which do not require precise output voltage,
setting the formula for calculating selected output voltage can
be simplified as follows:
f BW
0
fz(E SR) fp (FF)
fp(c)
-20
-40
-180
Pha se
[Deg.]
1
R2 = V Ref × --------------------------------------------------------------( R1 + R4 )
( V O – V Ref ) × ------------------------R1 × R4
-2 70
Linear Regulator Output Voltage
Φm
-3 60
1.0
The output voltage of the linear regulator (LDO) can be set
by a simple resistor divider according to the following formula:
R
V LDO = V Ref × ⎛⎝ 1 + ------U-⎞⎠
RL
10
100
10 00
10000
Frequency [k Hz ]
Figure 30. Buck Control Loop Bode Plot
The frequency of the zero created by the ESR of the output
capacitor CO is calculated as:
1
f z ( ESR ) = ------------------------2πC O ESR
Where CO is the value of the buck regulator output
capacitor, and ESR is the equivalent series resistance of the
output capacitor.
Where VRef is the linear regulator reference voltage
(VRef = 0.8 V typ.) at the LFB pin,
VLDO is the LDO selected output voltage,
RU is the “upper” resistor of the LDO resistor divider,
RL is the “lower” resistor of the LDO resistor divider.
Figure 31 describes the 34702 linear regulator circuit with
the resistor divider RU, RL setting the output voltage VLDO.
2.8 V to 6.0 V Input
MC34701
VIN1
The frequency of the compensating network pole can be
calculated as follows:
LDRV
1
f p ( c ) = ---------------------------------------R1R3
2πC2 ------------------------( R1 + R3 )
The well designed and compensated buck regulator
should yield at least 45 deg. phase margin Φm of its overall
loop as depicted in the Figure 30, page 31.
Selecting Buck Regulator Output Voltage
The 34702 buck regulator output voltage can be set by
selecting the right value of the resistors R1, R2 and R4, and
can be determined from the following formula (see Figure 29,
page 30 for the component references):
CS
RS
VLDO
LDO
RU
LFB
CLDO
RL
LCMP
LDO
Compensation
Figure 31. 34702 Linear Regulator Circuit
34702
Analog Integrated Circuit Device Data
Freescale Semiconductor
31
TYPICAL APPLICATIONS
Linear Regulator Current Limit
As described in the Linear Regulator Functional
Description section, the current limit of the linear regulator
can be adjusted by means of an external current sense
resistor RS. The voltage drop caused by the regulator output
current flowing through the current sense resistor RS is
sensed between the LDO and the CS pins. When the sensed
voltage exceeds 50 mV (typical), the current limit timer starts
to time out while the control circuit limits the output current. If
the overcurrent condition lasts for more than 10 ms, the linear
regulator is shut off and turned on again after 100 ms. This
type of operation provides equivalent protection to the analog
“current foldback” operation.
It is important to keep in mind that the amount of capacitive
load which can be supplied by the by the linear regulator is
limited by the setting of the LDO current limit. During the
power-up period, the linear regulator operates in the current
limit, supplying the current into the load of the LDO, which
includes all the capacitors connected to the regulator output.
If the total amount load is so large that the regulator could not
reach its regulation voltage in 10 ms during the power-up, it
turns off and tries to power up again after 100 ms. This
situation may lead to the power-up oscillations.
NOTE: Freescale does not assume liability, endorse, or warrant
components from external manufacturers referenced in figures
or tables. Although Freescale offers component
recommendations, it is the customer’s responsibility to validate
their application.
*When mounted to an FR4 using 0.5 sq.in. drain pad size
The maximum power dissipation is limited by the
maximum operating junction temperature TJmax. The
allowed power dissipation in the given application can be
calculated from the following expression:
T Jmax – T A
P D ( Q )max ≤ --------------------------------------------------------R thJC + R thCB + R thBA
Where PD(Q)max is the power MOSFET maximum
allowed dissipation,
TJmax is the power MOSFET maximum operating
junction temperature,
TA is the ambient temperature,
RthJC is the power MOSFET thermal resistance
junction-to-case,
RthCB is the thermal resistance case-to-board,
RthBA is the thermal resistance board-to-ambient of
the PC board.
Linear Regulator External MOSFET
The linear regulator uses an external N-channel power
MOSFET to provide a pass element for the power path. The
selection of the proper type of the external power MOSFET is
critical for optimum performance and safe operation of the
linear regulator.
The power MOSFET’s threshold voltage, RDS(on), gate
charge, capacitances and transconductance are important
parameters for the stable operation of the linear regulator
while the package of the power MOSFET determines the
maximum power dissipation, and hence the maximum output
current for the required input-to-output voltage drop. The
power dissipation of the external MOSFET can be calculated
from the simple formula:
P D ( Q ) = I LDO × ( V IN – V LDO )
Where PD(Q) is the power MOSFET power dissipation
VIN is the LDO input voltage,
VLDO is the LDO output voltage,
ILDO is the LDO output load current.
Table 10 shows the recommended power MOSFET types
for the 34702 linear regulator, their typical power dissipation,
and thermal resistance junction-to-case.
Table 10. Recommended Power MOSFETs
Part No.
Package
Typ. PD
RthJ-C
IRL2703S
D2PAK
2.0 W
3.3 °C/W
MTD20N03HDL
DPAK
1.75 W*
1.67 °C/W
PCB Layout Considerations
As with any power application, the proper PCB layout
plays a critical role in the overall power regulator
performance. While good careful printed circuit board layout
significantly improves regulation parameters and
electromagnetic compatibility (EMC) performance of the
switching regulator, poor layout practices can lead not only to
significant degradation of regulation and EMC parameters
but even to total dysfunction of the whole regulator IC.
Extreme care should be taken when laying out the ground
of the regulator circuit. In order to avoid any inductive or
capacitive coupling of the switching regulator noise into the
sensitive analog control circuits, the noisy power ground and
the clean quiet signal ground should be well separated on the
printed circuit board, and connected only at one connection
point. The power routing should be made by heavy traces or
areas of copper. The power path and its return should be
placed, if possible, atop each other on the different layers or
opposite sides of the PC board. The switching regulator input
and output capacitors should be physically placed very close
to the power pins (VIN2, SW, PGND) of the 34702 switching
regulator; and their ground pins, together with the 34702
power ground pins (PGND), should be connected by a single
island of the power ground copper to create the “single-point”
grounding. Figure 32 illustrates the 34702 switching regulator
grounding concept. The bootstrap capacitor Cb should be
tightly connected to the integrated circuit as well.
34702
32
Analog Integrated Circuit Device Data
Freescale Semiconductor
TYPICAL APPLICATIONS
VBST
BOOT
The same guidelines as those for the layout of the main
switching buck regulator should be applied to the layout of the
low power auxiliary boost regulator and to some extent, the
power path of the linear regulator.
Vin = 5.0 V
Cb
VIN2
Vout = 1.5 V
SW
To Load
INV
Vout Return
PGND
GND
Power
Ground
Signal
Ground
Figure 32. 34702 Buck Regulator Layout
34702
Analog Integrated Circuit Device Data
Freescale Semiconductor
33
TYPICAL APPLICATIONS
VIN1
+3.3V
Supply
Voltage
VIN
VDDI
Internal
Supply
CIN
10uF
VBST
8.0V
Power
Enable
-
10uH
Q5
Boost
Control
Vref
Vref
+3.3V
or
VLDO
LDRV
VDDI
VDDI
VBD
Bandgap
Voltage
Reference
Vref
Linear
Regulator
Control
LDO
I-lim
LFB
RS
0.022 R
5.1k
RST
RESET
to MCU
Q6
RT
VLDO
Power
Sequencing
Reset
Reset
Control
POR
Timer
Power
Down
Voltage Margining
@1.0A
INV
SysCon
Thermal
Limit
SoftSt
ADDR
SDA
Buck
Control
Logic
6.8nF
VBST
VIN2
+3.3V
Supply
Voltage
(2)
Buck
HS
&
LS
Driver
Q1
CIN
2 x 22 uF
SW
CB
DB
0.1uF
Error
Amp.
PWM
Comp.
+
-
Q2
To Reset
0.8V Control
+
FREQ
300k
39k
27k
Q3
+
(2)
VOUT
Pow.
Seq.
VOUT=1.8V
CO
100 uF
INV
-
Ramp
Gen.
CLKSYN
L1
4.7 uH
(2)
PGND
Switcher
Oscillator
300kHz
CLKSEL
1.5k
BOOT
I2C
Interface
SCL
CLDO
5 x 2.2 uF
VBST
VDDI
Ct
Rpd
UVLO
VBST
I2C
Control
LCMP
100pF
Current
Limit
SysCon
I2C
Control
Q4
VOUT
W-dog Timer
LFB
100nF
Pow. Seq.
VLDO=3.3V
4.7k
1.5k
EN1
RST
10k
QLDO
CS
VDDI
EN2
Rt
100k
1.0 uF
VBST
+
Vref
LBST
VDDI
VBST
7.75V
CBST
10uF
VDDI
Rb
300
VOUT
470pF
(4)
GND
RF
(Optional)
Figure 33. Simplified Block Diagram and Basic Application
34702
34
Analog Integrated Circuit Device Data
Freescale Semiconductor
1
GND
VIN
C36
1.0uF
+
C37
10uF
Optional
C37, L3
L3
3.3uH
1
2
RLF7030-3R3M4R1
C2
10uF
1
L2
D2
LL4148
C40 R18
4.7nF 2.2R
VBD
Optional
2
C40, R18
10uH
SLF6025T
C3
100uF
+
13
12
4
5
23
26
31
C33
10uF/16V
C18
1.0uF
C39
1.0uF
VIN2
27
28
15
16
32
1
MC34701
VDDI
ADDR
CLKSEL
VBST
VBD
VIN2
VIN2
EN1
EN2
SDA
SCL
CLKSYN
FREQ
7. C3, C10 = 100uF/6.3V, 10THB100ML POSCAP capacitor from Sanyo.
6. C2 = 10uF/10V, ceramic capacitor .
5. L3 = 3.3uH, RLF7030-3R3M4R1 from TDK
or 1812PS-103M from Coilcraft.
4. L2 = 10uH, SLF6025T-100M1R3 from TDK
or CDRH104R-4R7 from Sumida.
3. L1 = 4.7uH, DO3316P-472HC from Coilcraft
R12 = 36K for Vout = 1.5V.
R12 = 27K for Vout = 1.8V.
2. R12 = 16K for Vout = 2.5V
1. R11 can be adjusted according to the required LDO current limit.
NOTES:
1
1
SDA
SCL
1
VCC5V
1
CLKSY N
BOOT
U6
GND
8
R1
10k
GND
9
GND
24
Analog Integrated Circuit Device Data
Freescale Semiconductor
GND
25
VIN2
VIN1
VOUT
INV
PGND
PGND
SW
SW
BOOT
RT
/RESET
LCMP
LFB
LDO
CS
LDRV
3
2
10
11
6
7
14
29
30
17
18
C15
100nF
R12
1.5k
R17
C16
1.0uF
Signal ground
BOOT
LCMP
CS
20
19
LDRV
21
22
1
R10
300k
R4
10k
C7 33nF
C34
10nF
6.8nF
C35
L1
2
R8
39k
Power ground
R9
300R
C17
470pF
4.7uH
R11
0.022R
R15
1.5k
R13
4.7k
100uF
C10 +
10nF
C14
R19
510R
5 x 2.2 uF
C23
10uF
Q1
IRL2703S or MTD20N03HDL
5.1k
R2
3.3V
1
1
1
VOUT
RESET
VLDO
TYPICAL APPLICATIONS
Figure 34. 34702 Typical Application Circuit
34702
35
PACKAGE DIMENSIONS
PACKAGE DIMENSIONS
Important: For the most current package revision, visit www.freescale.com and perform a “keyword” search for
“98AARH99137A”.
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETERS.
2. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
3. DATUMS B AND C TO BE DETERMINED AT THE
PLANE WHERE THE BOTTOM OF THE LEADS
EXIT THE PLASTIC BODY.
4. THIS DIMENSION DOES NOT INCLUDE MOLD
FLASH, PROTRUSION OR GATE BURRS. MOLD
FLASH, PROTRUSION OR GATE BURRS SHALL
NOT EXCEED 0.15 MM PER SIDE. THIS
DIMENSION IS DETERMINED AT THE PLANE
WHERE THE BOTTOM OF THE LEADS EXIT THE
PLASTIC BODY.
5. THIS DIMENSION DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH AND PROTRUSIONS SHALL
NOT EXCEED 0.25 MM PER SIDE. THIS
DIMENSION IS DETERMINED AT THE PLANE
WHERE THE BOTTOM OF THE LEADS EXIT THE
PLASTIC BODY.
6. THIS DIMENSION DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL NOT CAUSE THE LEAD
WIDTH TO EXCEED 0.4 MM PER SIDE. DAMBAR
CANNOT BE LOCATED ON THE LOWER RADIUS
OR THE FOOT. MINIMUM SPACE BETWEEN
PROTRUSION AND ADJACENT LEAD SHALL NOT
LESS THAN 0.07 MM.
7. EXACT SHAPE OF EACH CORNER IS OPTIONAL.
8. THESE DIMENSIONS APPLY TO THE FLAT
SECTION OF THE LEAD BETWEEN 0.10 MM AND
0.3 MM FROM THE LEAD TIP.
9. THE PACKAGE TOP MAY BE SMALLER THAN
THE PACKAGE BOTTOM. THIS DIMENSION IS
DETERMINED AT THE OUTERMOST EXTREMES
OF THE PLASTIC BODY EXCLUSIVE OF MOLD
FLASH, TIE BAR BURRS, GATE BURRS AND
INTER–LEAD FLASH, BUT INCLUDING ANY
MISMATCH BETWEEN THE TOP AND BOTTOM
OF THE PLASTIC BODY.
10.3
7.6
7.4
C
5
B
2.65
2.35
9
30X
1
32
0.65
PIN 1 ID
4
B
9
B
16
11.1
10.9
CL
17
A
5.15
32X
2X 16 TIPS
0.3
SEATING
PLANE
A
B
0.10 A
C
A
ÇÇÇÇ
ÉÉÉ
ÇÇÇÇ
ÉÉÉ
ÇÇÇÇ
(0.29)
0.25
0.19
A
6
0.13
BASE METAL
(0.203)
0.38
0.22
M
C A
M
R0.08 MIN
0.25
PLATING
B
GAUGE PLANE
0°
MIN
0.29
0.13
8
SECTION A–A
ROTATED 90_ CLOCKWISE
8°
0°
0.9
0.5
SECTION B–B
98AARH99137A
CASE 1324–02
ISSUE A
34702
36
Analog Integrated Circuit Device Data
Freescale Semiconductor
REVISION HISTORY
REVISION HISTORY
REVISION
DATE
DESCRIPTION OF CHANGES
5.0
2/2006
•
Changed Document Order No.
6.0
2/2007
•
•
•
•
Updated to the current Freescale form and style.
Changed the status from Advance Information to Final.
Added Peak Package Reflow Temperature During Reflow (2), (3)
Added Notes (2) and (3)
34702
Analog Integrated Circuit Device Data
Freescale Semiconductor
37
How to Reach Us:
Home Page:
www.freescale.com
Web Support:
http://www.freescale.com/support
RoHS-compliant and/or Pb-free versions of Freescale products have the functionality
and electrical characteristics of their non-RoHS-compliant and/or non-Pb-free
counterparts. For further information, see http://www.freescale.com or contact your
Freescale sales representative.
For information on Freescale’s Environmental Products program, go to http://
www.freescale.com/epp.
USA/Europe or Locations Not Listed:
Freescale Semiconductor, Inc.
Technical Information Center, EL516
2100 East Elliot Road
Tempe, Arizona 85284
+1-800-521-6274 or +1-480-768-2130
www.freescale.com/support
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
www.freescale.com/support
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064
Japan
0120 191014 or +81 3 5437 9125
[email protected]
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
+800 2666 8080
[email protected]
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447 or 303-675-2140
Fax: 303-675-2150
[email protected]
MC34702
Rev 6.0
2/2007
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of any
product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters that may be
provided in Freescale Semiconductor data sheets and/or specifications can and do vary
in different applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer application by
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Semiconductor was negligent regarding the design or manufacture of the part.
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
All other product or service names are the property of their respective owners.
© Freescale Semiconductor, Inc., 2007. All rights reserved.
Similar pages