ON MC74HC4852ADT Analog multiplexers/demultiplexers with injection current effect control Datasheet

MC74HC4851A,
MC74HC4852A
Analog Multiplexers/
Demultiplexers with
Injection Current Effect
http://onsemi.com
Control
Automotive Customized
These devices are pin compatible to standard HC405x and
MC1405xB analog mux/demux devices, but feature injection current
effect control. This makes them especially suited for usage in
automotive applications where voltages in excess of normal logic
voltage are common.
The injection current effect control allows signals at disabled analog
input channels to exceed the supply voltage range without affecting
the signal of the enabled analog channel. This eliminates the need for
external diode/ resistor networks typically used to keep the analog
channel signals within the supply voltage range.
The devices utilize low power silicon gate CMOS technology. The
Channel Select and Enable inputs are compatible with standard CMOS
outputs.
• Injection Current Cross–Coupling Less than 1mV/mA (See Figure 9)
• Pin Compatible to HC405X and MC1405XB Devices
• Power Supply Range (VCC – GND) = 2.0 to 6.0 V
• In Compliance With the Requirements of JEDEC Standard No. 7A
• Chip Complexity: 154 FETs or 36 Equivalent Gates
MARKING
DIAGRAMS
16
PDIP–16
N SUFFIX
CASE 648
HC485xAN
AWLYYWW
1
16
SOIC–16
D SUFFIX
CASE 751B
HC485xAD
AWLYWW
1
16
SOIC–16 WIDE
DW SUFFIX
CASE 751G
HC485xADW
AWLYWW
1
16
TSSOP–16
DT SUFFIX
CASE 948F
HC48
5xA
ALYW
1
A
= Assembly Location
WL or L = Wafer Lot
YY or Y = Year
WW or W = Work Week
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 10 of this data sheet.
 Semiconductor Components Industries, LLC, 2000
March, 2000 – Rev. 4
1
Publication Order Number:
MC74HC4851A/D
MC74HC4851A, MC74HC4852A
FUNCTION TABLE – MC74HC4851A
Control Inputs
13
X0
14
X1
15
X2
ANALOG
12
MULTIPLEXER/
INPUTS/ X3
DEMULTIPLEXER
OUTPUTS X4 1
5
X5
2
X6
4
X7
11
A
CHANNEL
10
B
SELECT
9
INPUTS
C
6
ENABLE
PIN 16 = VCC
PIN 8 = GND
3
X
Select
B
A
ON Channels
Enable
C
L
L
L
L
L
L
L
L
H
L
L
L
L
H
H
H
H
X
L
L
H
H
L
L
H
H
X
X2
X1
X0
X3
A
B
C
15
14
13
12
11
10
9
6
7
COMMON
OUTPUT/
INPUT
VCC
16
L
H
L
H
L
H
L
H
X
X0
X1
X2
X3
X4
X5
X6
X7
NONE
Figure 1. MC74HC4851A Logic Diagram
Single–Pole, 8–Position Plus Common Off
1
2
3
4
5
X4
X6
X
X7
X5
Enable NC
8
GND
Figure 2. MC74HC4851A 16–Lead Pinout (Top View)
FUNCTION TABLE – MC74HC4852A
Control Inputs
Select
Enable
B
A
ON Channels
L
L
L
L
H
L
L
H
H
X
L
H
L
H
X
Y0
Y1
Y2
Y3
12
ANALOG
INPUTS/OUTPUTS
CHANNEL-SELECT
INPUTS
X0
14
X1
15
X2
11
X3
Y0
Y1
Y2
Y3
A
B
ENABLE
X SWITCH
13
X
COMMON
OUTPUTS/INPUTS
1
Y SWITCH
3
Y
4
VCC
16
10
9
NONE
X = Don’t Care
5
2
X0
X1
X2
X3
PIN 16 = VCC
PIN 8 = GND
X2
X1
X
X0
X3
A
B
15
14
13
12
11
10
9
6
7
8
GND
6
Figure 3. MC74HC4852A Logic Diagram
Double–Pole, 4–Position Plus Common Off
1
2
3
4
5
Y0
Y2
Y
Y3
Y1
Enable NC
Figure 4. MC74HC4852A 16–Lead Pinout (Top View)
http://onsemi.com
2
MC74HC4851A, MC74HC4852A
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
MAXIMUM RATINGS*
Symbol
Value
Unit
VCC
Positive DC Supply Voltage
(Referenced to GND)
– 0.5 to + 7.0
V
Vin
DC Input Voltage (Any Pin)
(Referenced to GND)
– 0.5 to VCC + 0.5
V
± 25
mA
750
500
450
mW
– 65 to + 150
_C
I
Parameter
DC Current, Into or Out of Any Pin
PD
Power Dissipation in Still Air,
Tstg
Storage Temperature Range
TL
Plastic DIP†
SOIC Package†
TSSOP Package†
_C
Lead Temperature, 1 mm from Case for 10 Seconds
Plastic DIP, SOIC or TSSOP Package
260
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high–impedance circuit. For proper operation, Vin and
Vout should be constrained to the
range GND (Vin or Vout) VCC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or VCC).
Unused outputs must be left open.
v
v
*Maximum Ratings are those values beyond which damage to the device may occur.
Functional operation should be restricted to the Recommended Operating Conditions.
†Derating — Plastic DIP: – 10 mW/_C from 65_ to 125_C
SOIC Package: – 7 mW/_C from 65_ to 125_C
TSSOP Package: – 6.1 mW/_C from 65_ to 125_C
For high frequency or heavy load considerations, see Chapter 2 of the ON Semiconductor High–Speed CMOS Data Book (DL129/D).
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
Min
Max
Unit
VCC
Positive DC Supply Voltage
(Referenced to GND)
2.0
6.0
V
Vin
DC Input Voltage (Any Pin)
(Referenced to GND)
GND
VCC
V
0.0
1.2
V
– 55
+ 125
_C
0
0
0
1000
500
400
ns
VIO*
Static or Dynamic Voltage Across Switch
TA
Operating Temperature Range, All Package Types
tr, tf
Input Rise/Fall Time
(Channel Select or Enable Inputs)
VCC = 2.0 V
VCC = 4.5 V
VCC = 6.0 V
*For voltage drops across switch greater than 1.2V (switch on), excessive VCC current may be
drawn; i.e., the current out of the switch may contain both VCC and switch input components.
The reliability of the device will be unaffected unless the Maximum Ratings are exceeded.
DC CHARACTERISTICS — Digital Section (Voltages Referenced to GND) VEE = GND, Except Where Noted
–55 to 25°C
≤85°C
≤125°C
Unit
Symbol
Parameter
VIH
Minimum High–Level Input
Voltage, Channel–Select or Enable
Inputs
Ron = Per Spec
2.0
3.0
4.5
6.0
1.50
2.10
3.15
4.20
1.50
2.10
3.15
4.20
1.50
2.10
3.15
4.20
V
VIL
Maximum Low–Level Input
Voltage, Channel–Select or Enable
Inputs
Ron = Per Spec
2.0
3.0
4.5
6.0
0.50
0.90
1.35
1.80
0.50
0.90
1.35
1.80
0.50
0.90
1.35
1.80
V
Iin
Maximum Input Leakage Current
on Digital Pins (Enable/A/B/C)
Vin = VCC or GND
6.0
± 0.1
± 1.0
± 1.0
µA
Maximum Quiescent Supply
Current (per Package)
Vin(digital) = VCC or GND
Vin(analog) = GND
6.0
2
20
40
µA
ICC
Condition
Guaranteed Limit
VCC
V
NOTE: Information on typical parametric values can be found in Chapter 2 of the ON Semiconductor High–Speed CMOS Data Book (DL129/D).
http://onsemi.com
3
MC74HC4851A, MC74HC4852A
DC CHARACTERISTICS — Analog Section
Guaranteed Limit
Condition
VCC
–55 to 25°C
≤85°C
≤125°C
Unit
Maximum “ON” Resistance
Vin = VIL or VIH;VIS = VCC to
GND; IS ≤ 2.0 mA
2.0
3.0
4.5
6.0
1700
1100
550
400
1750
1200
650
500
1800
1300
750
600
Ω
Delta “ON” Resistance
Vin = VIL or VIH; VIS = VCC/2
IS ≤ 2.0 mA
2.0
3.0
4.5
6.0
300
160
80
60
400
200
100
80
500
240
120
100
Ω
Maximum Off–Channel Leakage
Current,
Any One Channel
Common Channel
Vin = VCC or GND
6.0
±0.1
±0.2
±0.5
±2.0
±1.0
±4.0
Maximum On–Channel Leakage
Channel–to–Channel
Vin = VCC or GND
6.0
±0.2
±2.0
±4.0
VCC
–55 to 25°C
≤85°C
≤125°C
Unit
Maximum Propagation Delay, Analog Input to Analog Output
2.0
3.0
4.5
6.0
160
80
40
30
180
90
45
35
200
100
50
40
ns
Maximum Propagation Delay, Enable or Channel–Select to
Analog Output
2.0
3.0
4.5
6.0
260
160
80
60
280
180
90
70
300
200
100
80
ns
10
35
130
10
35
130
10
35
130
pF
Symbol
Ron
∆Ron
Ioff
Ion
Parameter
µA
µA
AC CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6 ns)
Symbol
Parameter
tPHL,
tPLH
tPHL, tPHZ,PZH
tPLH, tPLZ,PZL
Cin
CPD
Maximum Input Capacitance
(All Switches Off)
(All Switches Off)
Digital Pins
Any Single Analog Pin
Common Analog Pin
Power Dissipation Capacitance
Typical
5.0
20
pF
INJECTION CURRENT COUPLING SPECIFICATIONS (VCC = 5V, TA = –55°C to +125°C)
Symbol
V∆out
Parameter
Maximum Shift of Output Voltage of Enabled Analog
Channel
Typ
Max
Unit
0.1
1.0
0.5
5.0
1.0
5.0
2.0
20
mV
* Iin = Total current injected into all disabled channels.
http://onsemi.com
4
Condition
Iin* ≤ 1mA, RS ≤ 3,9kΩ
Iin* ≤ 10mA, RS ≤ 3,9kΩ
Iin* ≤ 1mA, RS ≤ 20kΩ
Iin* ≤ 10mA, RS ≤ 20kΩ
MC74HC4851A, MC74HC4852A
1100
1000
R on , ON RESISTANCE (OHMS)
900
–55°C
800
+25°C
700
+125°C
600
500
400
300
200
R on , ON RESISTANCE (OHMS)
1100
1000
100
800
700
600
500
–55°C
400
+25°C
300
+125°C
200
100
0
0.0
0.4
0.8
1.2
1.6
0
0.0
2.0
1.2
1.8
2.4
Vin, INPUT VOLTAGE (VOLTS), REFERENCED TO GND
Figure 5. Typical On Resistance VCC = 2V
Figure 6. Typical On Resistance VCC = 3V
660
440
600
400
540
360
480
420
360
–55°C
300
+25°C
240
+125°C
180
–55°C
280
160
120
40
2.7
3.6
+125°C
200
60
1.8
+25°C
240
80
0.9
0
0.0
4.5
1.2
2.4
3.6
4.8
Vin, INPUT VOLTAGE (VOLTS), REFERENCED TO GND
Vin, INPUT VOLTAGE (VOLTS), REFERENCED TO GND
Figure 7. Typical On Resistance VCC = 4.5V
Figure 8. Typical On Resistance VCC = 6V
http://onsemi.com
5
3.0
320
120
0
0.0
0.6
Vin, INPUT VOLTAGE (VOLTS), REFERENCED TO GND
R on , ON RESISTANCE (OHMS)
R on , ON RESISTANCE (OHMS)
900
6.0
MC74HC4851A, MC74HC4852A
VCC = 5V
Iin
Vin2 < VSS or VCC < Vin2
Any Disabled Channel
VSS < Vin1 < VCC
Enabled Channel
Vout = Vin1 ±V∆out
RS
Figure 9. Injection Current Coupling Specification
5V
6V
5V
HC4051A
Sensor
VCC
VCC
Microcontroller
Channel 1
Channel 2
Channel 3
Channel 4
Channel 5
Channel 6
Channel 7
Channel 8
(8x Identical Circuitry)
Common Out
A/D – Input
Figure 10. Actual Technology
Requires 32 passive components and one extra 6V regulator
to suppress injection current into a standard HC4051 multiplexer
5V
VCC
HC4851A
Sensor
VCC
Microcontroller
Channel 1
Channel 2
Channel 3
Channel 4
Channel 5
Channel 6
Channel 7
Channel 8
(8x Identical Circuitry)
Common Out
A/D – Input
Figure 11. MC74HC4851A Solution
Solution by applying the HC4851A multiplexer
http://onsemi.com
6
MC74HC4851A, MC74HC4852A
PLOTTER
VCC
PROGRAMMABLE
POWER
SUPPLY
MINI COMPUTER
DC ANALYZER
16
VEE
VCC
OFF
–
+
VCC
VCC
A
COMMON O/I
OFF
NC
DEVICE
UNDER TEST
ANALOG IN
VIH
COMMON OUT
6
8
GND
Figure 13. Maximum Off Channel Leakage Current,
Any One Channel, Test Set–Up
Figure 12. On Resistance Test
Set–Up
VCC
16
VEE
ANALOG I/O
16
A
OFF
VCC
OFF
VIH
VCC
VCC
VCC
ON
VEE
COMMON O/I
VCC
N/C
ANALOG I/O
VIL
6
COMMON O/I
OFF
6
8
8
Figure 14. Maximum Off Channel Leakage Current,
Common Channel, Test Set–Up
Figure 15. Maximum On Channel Leakage Current,
Channel to Channel, Test Set–Up
VCC
16
VCC
VCC
CHANNEL
SELECT
ON/OFF
50%
OFF/ON
GND
tPLH
ANALOG
OUT
COMMON O/I
ANALOG I/O
TEST
POINT
CL*
tPHL
6
50%
8
CHANNEL SELECT
*Includes all probe and jig capacitance
Figure 16. Propagation Delays, Channel Select
to Analog Out
Figure 17. Propagation Delay, Test Set–Up Channel
Select to Analog Out
http://onsemi.com
7
MC74HC4851A, MC74HC4852A
VCC
16
ANALOG
IN
COMMON O/I
ANALOG I/O
VCC
ON
50%
TEST
POINT
CL*
GND
tPHL
tPLH
ANALOG
OUT
6
8
50%
*Includes all probe and jig capacitance
Figure 18. Propagation Delays, Analog In
to Analog Out
tf
tr
tPZL
POSITION 1 WHEN TESTING tPHZ AND tPZH
POSITION 2 WHEN TESTING tPLZ AND tPZL
1
VCC
90%
50%
10%
ENABLE
ANALOG
OUT
Figure 19. Propagation Delay, Test Set–Up
Analog In to Analog Out
2
GND
tPLZ
HIGH
IMPEDANCE
1
CL*
tPZH tPHZ
ANALOG
OUT
TEST
POINT
ON/OFF
VOL
ENABLE
VOH
90%
10kΩ
ANALOG I/O
2
50%
10%
VCC
16
VCC
50%
6
8
HIGH
IMPEDANCE
Figure 20. Propagation Delays, Enable to
Analog Out
Figure 21. Propagation Delay, Test Set–Up
Enable to Analog Out
VCC
A
VCC
16
COMMON O/I
ON/OFF
NC
ANALOG I/O
OFF/ON
VCC
6
8
11
CHANNEL SELECT
Figure 22. Power Dissipation Capacitance,
Test Set–Up
http://onsemi.com
8
MC74HC4851A, MC74HC4852A
Gate = VCC
(Disabled)
Disabled Analog Mux Input
Vin > VCC + 0.7V
P+
Common Analog Output
Vout > VCC
P+
+
+
+
N – Substrate (on VCC potential)
Figure 23. Diagram of Bipolar Coupling Mechanism
Appears if Vin exceeds VCC, driving injection current into the substrate
A
B
C
ENABLE
11
10
9
6
Figure 24. Function Diagram, HC4851A
http://onsemi.com
9
INJECTION
CURRENT
CONTROL
13
INJECTION
CURRENT
CONTROL
14
INJECTION
CURRENT
CONTROL
15
INJECTION
CURRENT
CONTROL
12
INJECTION
CURRENT
CONTROL
1
INJECTION
CURRENT
CONTROL
5
INJECTION
CURRENT
CONTROL
2
INJECTION
CURRENT
CONTROL
4
INJECTION
CURRENT
CONTROL
3
X0
X1
X2
X3
X4
X5
X6
X7
X
MC74HC4851A, MC74HC4852A
A
B
ENABLE
10
9
6
INJECTION
CURRENT
CONTROL
13
INJECTION
CURRENT
CONTROL
14
INJECTION
CURRENT
CONTROL
15
INJECTION
CURRENT
CONTROL
12
INJECTION
CURRENT
CONTROL
13
INJECTION
CURRENT
CONTROL
1
INJECTION
CURRENT
CONTROL
5
INJECTION
CURRENT
CONTROL
2
INJECTION
CURRENT
CONTROL
4
INJECTION
CURRENT
CONTROL
3
Figure 25. Function Diagram, HC4852A
ORDERING & SHIPPING INFORMATION
Package
Shipping
MC74HC4851AN
Device
PDIP–16
500 Units / Unit Pak
MC74HC4851AD
SOIC–16
48 Units / Rail
MC74HC4851ADR2
SOIC–16
2500 Units / Tape & Reel
MC74HC4851ADW
SOIC–16 WIDE
48 Units / Rail
MC74HC4851ADWR2
SOIC–16 WIDE
1000 Units / Tape & Reel
MC74HC4851ADT
TSSOP–16
96 Units / Rail
MC74HC4851ADTR2
TSSOP–16
2500 Units / Tape & Reel
MC74HC4852AN
PDIP–16
500 Units / Unit Pak
MC74HC4852AD
SOIC–16
48 Units / Rail
MC74HC4852ADR2
SOIC–16
2500 Units / Tape & Reel
MC74HC4852ADW
SOIC–16 WIDE
48 Units / Rail
MC74HC4852ADWR2
SOIC–16 WIDE
1000 Units / Tape & Reel
MC74HC4852ADT
TSSOP–16
96 Units / Rail
MC74HC4852ADTR2
TSSOP–16
2500 Units / Tape & Reel
http://onsemi.com
10
X0
X1
X2
X3
X
Y0
Y1
Y2
Y3
Y
MC74HC4851A, MC74HC4852A
PACKAGE DIMENSIONS
PDIP–16
N SUFFIX
CASE 648–08
ISSUE R
–A
–
16
9
1
8
B
F
C
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
DIM
A
B
C
D
F
G
H
J
K
L
M
S
L
S
SEATING
PLANE
–T
–
K
H
D 16 PL
0.25 (0.010)
M
J
G
T A
M
M
SOIC–16
D SUFFIX
CASE 751B–05
ISSUE J
–A
–
16
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
9
–B
–
1
P 8 PL
0.25 (0.010)
8
B
M
M
G
K
DIM
A
B
C
D
F
G
J
K
M
P
R
F
R X 45°
C
–T
SEATING
–
J
M
PLANE
D 16 PL
0.25 (0.010)
M
T
B
A
S
S
SOIC–16 WIDE
DW SUFFIX
CASE 751G–02
ISSUE A
–A–
16
9
–B–
8X
P
0.010 (0.25)
1
M
B
M
8
16X
J
D
0.010 (0.25)
M
T A
S
B
S
F
R X 45 _
C
–T–
14X
G
K
SEATING
PLANE
M
http://onsemi.com
11
INCHES
MILLIMETERS
MIN
MAX
MIN
MAX
0.740 0.770 18.80 19.55
0.250 0.270
6.35
6.85
0.145 0.175
3.69
4.44
0.015 0.021
0.39
0.53
0.040 0.070
1.02
1.77
0.100 BSC
2.54 BSC
0.050 BSC
1.27 BSC
0.008 0.015
0.21
0.38
0.110 0.130
2.80
3.30
0.295 0.305
7.50
7.74
0°
10°
0°
10°
0.020 0.040
0.51
1.01
MILLIMETERS
MIN
MAX
9.80 10.00
4.00
3.80
1.75
1.35
0.49
0.35
1.25
0.40
1.27 BSC
0.25
0.19
0.25
0.10
7°
0°
6.20
5.80
0.50
0.25
INCHES
MIN
MAX
0.386 0.393
0.150 0.157
0.054 0.068
0.014 0.019
0.016 0.049
0.050 BSC
0.008 0.009
0.004 0.009
0°
7°
0.229 0.244
0.010 0.019
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER
SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.13 (0.005) TOTAL IN
EXCESS OF D DIMENSION AT MAXIMUM
MATERIAL CONDITION.
DIM
A
B
C
D
F
G
J
K
M
P
R
MILLIMETERS
MIN
MAX
10.15
10.45
7.40
7.60
2.35
2.65
0.35
0.49
0.50
0.90
1.27 BSC
0.25
0.32
0.10
0.25
0_
7_
10.05
10.55
0.25
0.75
INCHES
MIN
MAX
0.400
0.411
0.292
0.299
0.093
0.104
0.014
0.019
0.020
0.035
0.050 BSC
0.010
0.012
0.004
0.009
0_
7_
0.395
0.415
0.010
0.029
MC74HC4851A, MC74HC4852A
PACKAGE DIMENSIONS
TSSOP–16
DT SUFFIX
CASE 948F–01
ISSUE O
16X K REF
0.10 (0.004)
0.15 (0.006) T U
T U
M
V
S
S
S
K
ÉÉÉ
ÇÇÇ
ÇÇÇ
ÉÉÉ
K1
2X
L/2
16
9
J1
B
–U–
L
SECTION N–N
J
PIN 1
IDENT.
8
1
N
0.25 (0.010)
0.15 (0.006) T U
S
A
–V–
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH.
PROTRUSIONS OR GATE BURRS. MOLD FLASH OR
GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER
SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH OR
PROTRUSION SHALL NOT EXCEED
0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K
DIMENSION AT MAXIMUM MATERIAL CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE DETERMINED AT
DATUM PLANE –W–.
M
N
F
DETAIL E
–W–
C
0.10 (0.004)
–T– SEATING
PLANE
DETAIL E
H
D
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
MILLIMETERS
MIN
MAX
4.90
5.10
4.30
4.50
–––
1.20
0.05
0.15
0.50
0.75
0.65 BSC
0.18
0.28
0.09
0.20
0.09
0.16
0.19
0.30
0.19
0.25
6.40 BSC
0_
8_
INCHES
MIN
MAX
0.193
0.200
0.169
0.177
–––
0.047
0.002
0.006
0.020
0.030
0.026 BSC
0.007
0.011
0.004
0.008
0.004
0.006
0.007
0.012
0.007
0.010
0.252 BSC
0_
8_
G
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
NORTH AMERICA Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: [email protected]
Fax Response Line: 303–675–2167 or 800–344–3810 Toll Free USA/Canada
N. American Technical Support: 800–282–9855 Toll Free USA/Canada
EUROPE: LDC for ON Semiconductor – European Support
German Phone: (+1) 303–308–7140 (M–F 1:00pm to 5:00pm Munich Time)
Email: ONlit–[email protected]
French Phone: (+1) 303–308–7141 (M–F 1:00pm to 5:00pm Toulouse Time)
Email: ONlit–[email protected]
English Phone: (+1) 303–308–7142 (M–F 12:00pm to 5:00pm UK Time)
Email: [email protected]
EUROPEAN TOLL–FREE ACCESS*: 00–800–4422–3781
*Available from Germany, France, Italy, England, Ireland
CENTRAL/SOUTH AMERICA:
Spanish Phone: 303–308–7143 (Mon–Fri 8:00am to 5:00pm MST)
Email: ONlit–[email protected]
ASIA/PACIFIC: LDC for ON Semiconductor – Asia Support
Phone: 303–675–2121 (Tue–Fri 9:00am to 1:00pm, Hong Kong Time)
Toll Free from Hong Kong & Singapore:
001–800–4422–3781
Email: ONlit–[email protected]
JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–8549
Phone: 81–3–5740–2745
Email: [email protected]
ON Semiconductor Website: http://onsemi.com
For additional information, please contact your local
Sales Representative.
http://onsemi.com
12
MC74HC4851A/D
Similar pages