MOTOROLA MC74HCXXXXADW Analog multiplexers/ demultiplexer Datasheet

SEMICONDUCTOR TECHNICAL DATA
High–Performance Silicon–Gate CMOS
The MC54/74HC4051A, MC74HC4052A and MC54/74HC4053A utilize
silicon–gate CMOS technology to achieve fast propagation delays, low ON
resistances, and low OFF leakage currents. These analog multiplexers/
demultiplexers control analog voltages that may vary across the complete
power supply range (from VCC to VEE).
The HC4051A, HC4052A and HC4053A are identical in pinout to the
metal–gate MC14051AB, MC14052AB and MC14053AB. The Channel–Select inputs determine which one of the Analog Inputs/Outputs is to be
connected, by means of an analog switch, to the Common Output/Input.
When the Enable pin is HIGH, all analog switches are turned off.
The Channel–Select and Enable inputs are compatible with standard
CMOS outputs; with pullup resistors they are compatible with LSTTL
outputs.
These devices have been designed so that the ON resistance (Ron) is
more linear over input voltage than R on of metal–gate CMOS analog
switches.
For a multiplexer/demultiplexer with channel–select latches, see
HC4351A.
• Fast Switching and Propagation Speeds
• Low Crosstalk Between Switches
• Diode Protection on All Inputs/Outputs
• Analog Power Supply Range (VCC – VEE) = 2.0 to 12.0 V
• Digital (Control) Power Supply Range (VCC – GND) = 2.0 to 6.0 V
• Improved Linearity and Lower ON Resistance Than Metal–Gate
Counterparts
• Low Noise
• In Compliance With the Requirements of JEDEC Standard No. 7A
• Chip Complexity: HC4051A — 184 FETs or 46 Equivalent Gates
HC4052A — 168 FETs or 42 Equivalent Gates
HC4053A — 156 FETs or 39 Equivalent Gates
ORDERING INFORMATION
Control Inputs
Enable
C
L
L
L
L
L
L
L
L
H
L
L
L
L
H
H
H
H
X
14
13
12
11
10
9
6
7
5
X5
8
Enable VEE
GND
This document contains information on a new product. Specifications and information herein are subject to
change without notice.
10/97
 Motorola, Inc. 1997
1
Select
B
A
L
L
H
H
L
L
H
H
X
L
H
L
H
L
H
L
H
X
ON Channels
X0
X1
X2
X3
X4
X5
X6
X7
NONE
X = Don’t Care
15
4
Ceramic
Plastic
SOIC
SOIC Wide
TSSOP
FUNCTION TABLE – MC54/74HC4051A
C
X7
1
DT SUFFIX
TSSOP PACKAGE
CASE 948F–01
MC54HCXXXXAJ
MC74HCXXXXAN
MC74HCXXXXAD
MC74HCXXXXADW
MC74HCXXXXADT
B
3
1
DW SUFFIX
SOIC WIDE PACKAGE
CASE 751G–02
16
A
X
D SUFFIX
SOIC PACKAGE
CASE 751B–05
16
X3
2
N SUFFIX
PLASTIC PACKAGE
CASE 648–08
1
X0
X6
16
X1
1
1
X2
X4
J SUFFIX
CERAMIC PACKAGE
CASE 620–10
Pinout: MC54/74HC4051A (Top View)
VCC
16
16
COMMON
OUTPUT/
INPUT
X
1
13
3
16
LOGIC DIAGRAM
MC54/74HC4051A
Single–Pole, 8–Position Plus Common Off
X0
14
X1
15
X2
ANALOG
12
MULTIPLEXER/
INPUTS/ X3
DEMULTIPLEXER
OUTPUTS X4 1
5
X5
2
X6
4
X7
11
A
CHANNEL
10
B
SELECT
9
INPUTS
C
6
ENABLE
PIN 16 = VCC
PIN 7 = VEE
PIN 8 = GND
REV 0
MC54/74HC4051A MC74HC4052A MC54/74HC4053A
FUNCTION TABLE – MC74HC4052A
LOGIC DIAGRAM
MC74HC4052A
Double–Pole, 4–Position Plus Common Off
Control Inputs
Select
Enable
B
A
ON Channels
L
L
L
L
H
L
L
H
H
X
L
H
L
H
X
Y0
Y1
Y2
Y3
12
ANALOG
INPUTS/OUTPUTS
CHANNEL-SELECT
INPUTS
X0
14
X1
15
X2
11
X3
Y0
Y1
Y2
Y3
A
B
ENABLE
X SWITCH
13
X
COMMON
OUTPUTS/INPUTS
1
5
2
Y SWITCH
3
X0
X1
X2
X3
NONE
X = Don’t Care
Y
4
Pinout: MC74HC4052A (Top View)
10
9
VCC
16
PIN 16 = VCC
PIN 7 = VEE
PIN 8 = GND
6
X2
X1
X
X0
X3
A
B
15
14
13
12
11
10
9
6
7
8
GND
1
2
3
4
5
Y0
Y2
Y
Y3
Y1
Enable VEE
FUNCTION TABLE – MC54/74HC4053A
LOGIC DIAGRAM
MC54/74HC4053A
Triple Single–Pole, Double–Position Plus Common Off
12
X0
13
X1
X SWITCH
2
ANALOG
INPUTS/OUTPUTS
Y0
1
Y1
Y SWITCH
5
Z0
3
Z1
Z SWITCH
14
15
4
Control Inputs
Enable
C
L
L
L
L
L
L
L
L
H
L
L
L
L
H
H
H
H
X
X
Y
COMMON
OUTPUTS/INPUTS
Select
B
A
L
L
H
H
L
L
H
H
X
ON Channels
Z0
Z0
Z0
Z0
Z1
Z1
Z1
Z1
L
H
L
H
L
H
L
H
X
Y0
Y0
Y1
Y1
Y0
Y0
Y1
Y1
NONE
X0
X1
X0
X1
X0
X1
X0
X1
X = Don’t Care
Z
11
A
10
CHANNEL-SELECT
B
INPUTS
9
C
6
ENABLE
PIN 16 = VCC
PIN 7 = VEE
PIN 8 = GND
Pinout: MC54/74HC4053A (Top View)
VCC
16
Y
X
X1
X0
A
B
C
15
14
13
12
11
10
9
1
2
3
4
5
6
7
Y1
Y0
Z1
Z
Z0
8
GND
NOTE: This device allows independent control of each switch.
Channel–Select Input A controls the X–Switch, Input B controls
the Y–Switch and Input C controls the Z–Switch
MOTOROLA
2
Enable VEE
High–Speed CMOS Logic Data
DL129 — Rev 6
MC54/74HC4051A MC74HC4052A MC54/74HC4053A
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎ
MAXIMUM RATINGS*
Symbol
Parameter
Unit
– 0.5 to + 7.0
– 0.5 to + 14.0
V
VCC
Positive DC Supply Voltage
VEE
Negative DC Supply Voltage (Referenced to GND)
– 7.0 to + 5.0
V
VIS
Analog Input Voltage
VEE – 0.5 to
VCC + 0.5
V
Vin
Digital Input Voltage (Referenced to GND)
– 0.5 to VCC + 0.5
V
± 25
mA
750
500
450
mW
– 65 to + 150
_C
I
PD
Tstg
TL
(Referenced to GND)
(Referenced to VEE)
Value
DC Current, Into or Out of Any Pin
Power Dissipation in Still Air, Plastic or Ceramic DIP†
SOIC Package†
TSSOP Package†
Storage Temperature Range
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high–impedance circuit. For proper operation, Vin and
Vout should be constrained to the
range GND (Vin or Vout) VCC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or VCC).
Unused outputs must be left open.
v
v
_C
Lead Temperature, 1 mm from Case for 10 Seconds
Plastic DIP, SOIC or TSSOP Package
Ceramic DIP
260
300
* Maximum Ratings are those values beyond which damage to the device may occur.
Functional operation should be restricted to the Recommended Operating Conditions.
†Derating — Plastic DIP: – 10 mW/_C from 65_ to 125_C
Ceramic DIP: – 10 mW/_C from 100_ to 125_C
SOIC Package: – 7 mW/_C from 65_ to 125_C
TSSOP Package: – 6.1 mW/_C from 65_ to 125_C
For high frequency or heavy load considerations, see Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
(Referenced to GND)
(Referenced to VEE)
Min
Max
Unit
2.0
2.0
6.0
12.0
V
VCC
Positive DC Supply Voltage
VEE
Negative DC Supply Voltage, Output (Referenced to
GND)
– 6.0
GND
V
VIS
Analog Input Voltage
VEE
VCC
V
Vin
Digital Input Voltage (Referenced to GND)
GND
VCC
V
VIO*
Static or Dynamic Voltage Across Switch
1.2
V
– 55
+ 125
_C
0
0
0
0
1000
600
500
400
ns
TA
Operating Temperature Range, All Package Types
tr, tf
Input Rise/Fall Time
(Channel Select or Enable Inputs)
VCC = 2.0 V
VCC = 3.0 V
VCC = 4.5 V
VCC = 6.0 V
* For voltage drops across switch greater than 1.2V (switch on), excessive VCC current may be
drawn; i.e., the current out of the switch may contain both VCC and switch input components. The
reliability of the device will be unaffected unless the Maximum Ratings are exceeded.
High–Speed CMOS Logic Data
DL129 — Rev 6
3
MOTOROLA
MC54/74HC4051A MC74HC4052A MC54/74HC4053A
DC CHARACTERISTICS — Digital Section (Voltages Referenced to GND) VEE = GND, Except Where Noted
–55 to 25°C
≤85°C
≤125°C
U i
Unit
S b l
Symbol
P
Parameter
VIH
Minimum High–Level Input Voltage,
Channel–Select or Enable Inputs
Ron = Per Spec
2.0
3.0
4.5
6.0
1.50
2.10
3.15
4.20
1.50
2.10
3.15
4.20
1.50
2.10
3.15
4.20
V
VIL
Maximum Low–Level Input Voltage,
Channel–Select or Enable Inputs
Ron = Per Spec
2.0
3.0
4.5
6.0
0.5
0.9
1.35
1.8
0.5
0.9
1.35
1.8
0.5
0.9
1.35
1.8
V
Iin
Maximum Input Leakage Current,
Channel–Select or Enable Inputs
Vin = VCC or GND,
VEE = – 6.0 V
6.0
± 0.1
± 1.0
± 1.0
µA
Maximum Quiescent Supply
Current (per Package)
Channel Select, Enable and
VIS = VCC or GND; VEE = GND
VIO = 0 V
VEE = – 6.0
6.0
6.0
1
4
10
40
20
80
ICC
C di i
Condition
Guaranteed Limit
VCC
V
µA
NOTE: Information on typical parametric values can be found in Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).
DC CHARACTERISTICS — Analog Section
Guaranteed Limit
S b l
Symbol
Ron
P
Parameter
Maximum “ON” Resistance
C di i
Condition
VCC
VEE
–55 to 25°C
≤85°C
≤125°C
U i
Unit
Vin = VIL or VIH; VIS = VCC to
VEE; IS ≤ 2.0 mA
(Figures 1, 2)
4.5
4.5
6.0
0.0
– 4.5
– 6.0
190
120
100
240
150
125
280
170
140
Ω
Vin = VIL or VIH; VIS = VCC or
VEE (Endpoints); IS ≤ 2.0 mA
(Figures 1, 2)
4.5
4.5
6.0
0.0
– 4.5
– 6.0
150
100
80
190
125
100
230
140
115
∆Ron
Maximum Difference in “ON”
Resistance Between Any Two
Channels in the Same Package
Vin = VIL or VIH;
VIS = 1/2 (VCC – VEE);
IS ≤ 2.0 mA
4.5
4.5
6.0
0.0
– 4.5
– 6.0
30
12
10
35
15
12
40
18
14
Ioff
Maximum Off–Channel Leakage
Current, Any One Channel
Vin = VIL or VIH;
VIO = VCC – VEE;
Switch Off (Figure 3)
6.0
– 6.0
0.1
0.5
1.0
Maximum Off–Channel HC4051A
Leakage Current,
HC4052A
Common Channel
HC4053A
Vin = VIL or VIH;
VIO = VCC – VEE;
Switch Off (Figure 4)
6.0
6.0
6.0
– 6.0
– 6.0
– 6.0
0.2
0.1
0.1
2.0
1.0
1.0
4.0
2.0
2.0
Maximum On–Channel HC4051A
Leakage Current,
HC4052A
Channel–to–Channel HC4053A
Vin = VIL or VIH;
Switch–to–Switch =
VCC – VEE; (Figure 5)
6.0
6.0
6.0
– 6.0
– 6.0
– 6.0
0.2
0.1
0.1
2.0
1.0
1.0
4.0
2.0
2.0
Ion
MOTOROLA
Ω
µA
4
µA
High–Speed CMOS Logic Data
DL129 — Rev 6
MC54/74HC4051A MC74HC4052A MC54/74HC4053A
AC CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6 ns)
S b l
Symbol
P
Parameter
Guaranteed Limit
VCC
V
–55 to 25°C
≤85°C
≤125°C
U i
Unit
tPLH,
tPHL
Maximum Propagation Delay, Channel–Select to Analog Output
(Figure 9)
2.0
4.5
6.0
370
74
63
465
93
79
550
110
94
ns
tPLH,
tPHL
Maximum Propagation Delay, Analog Input to Analog Output
(Figure 10)
2.0
4.5
6.0
60
12
10
75
15
13
90
18
15
ns
tPLZ,
tPHZ
Maximum Propagation Delay, Enable to Analog Output
(Figure 11)
2.0
4.5
6.0
290
58
49
364
73
62
430
86
73
ns
tPZL,
tPZH
Maximum Propagation Delay, Enable to Analog Output
(Figure 11)
2.0
4.5
6.0
345
69
59
435
87
74
515
103
87
ns
Cin
Maximum Input Capacitance, Channel–Select or Enable Inputs
10
10
10
pF
CI/O
Maximum Capacitance
Analog I/O
35
35
35
pF
Common O/I: HC4051A
HC4052A
HC4053A
130
80
50
130
80
50
130
80
50
Feedthrough
1.0
1.0
1.0
(All Switches Off)
NOTE: For propagation delays with loads other than 50 pF, and information on typical parametric values, see Chapter 2 of the Motorola High–
Speed CMOS Data Book (DL129/D).
Typical @ 25°C, VCC = 5.0 V, VEE = 0 V
CPD
P
Power
Di
Dissipation
i i C
Capacitance
i
(Fi
(Figure 13)*
HC4051A
HC4052A
HC4053A
45
80
45
pF
F
* Used to determine the no–load dynamic power consumption: P D = C PD V CC 2 f + I CC V CC . For load considerations, see Chapter 2 of the
Motorola High–Speed CMOS Data Book (DL129/D).
High–Speed CMOS Logic Data
DL129 — Rev 6
5
MOTOROLA
MC54/74HC4051A MC74HC4052A MC54/74HC4053A
ADDITIONAL APPLICATION CHARACTERISTICS (GND = 0 V)
S b l
Symbol
BW
—
—
—
THD
P
Parameter
C di i
Condition
VCC
V
Limit*
VEE
V
Maximum On–Channel Bandwidth
or Minimum Frequency Response
(Figure 6)
fin = 1MHz Sine Wave; Adjust fin Voltage to
Obtain 0dBm at VOS; Increase fin
i Frequency
Until dB Meter Reads –3dB;
RL = 50Ω, CL = 10pF
2.25
2
25
4.50
6.00
–2.25
–4.50
–6.00
Off–Channel Feedthrough Isolation
(Figure 7)
fin = Sine Wave; Adjust fin Voltage to Obtain
0dBm at VIS
fin = 10kHz, RL = 600Ω, CL = 50pF
2.25
4.50
6.00
–2.25
–4.50
–6.00
–50
–50
–50
fin = 1.0MHz, RL = 50Ω, CL = 10pF
2.25
4.50
6.00
–2.25
–4.50
–6.00
–40
–40
–40
Vin ≤ 1MHz Square Wave (tr = tf = 6ns);
Adjust RL at Setup so that IS = 0A;
Enable = GND
RL = 600Ω, CL = 50pF
2.25
4.50
6.00
–2.25
–4.50
–6.00
25
105
135
RL = 10kΩ, CL = 10pF
2.25
4.50
6.00
–2.25
–4.50
–6.00
35
145
190
fin = Sine Wave; Adjust fin Voltage to Obtain
0dBm at VIS
fin = 10kHz, RL = 600Ω, CL = 50pF
2.25
4.50
6.00
–2.25
–4.50
–6.00
–50
–50
–50
fin = 1.0MHz, RL = 50Ω, CL = 10pF
2.25
4.50
6.00
–2.25
–4.50
–6.00
–60
–60
–60
Feedthrough Noise.
Channel–Select Input to Common
I/O (Figure 8)
Crosstalk Between Any Two
Switches (Figure 12)
(Test does not apply to HC4051A)
Total Harmonic Distortion
(Figure 14)
fin = 1kHz, RL = 10kΩ, CL = 50pF
THD = THDmeasured – THDsource
VIS = 4.0VPP sine wave
VIS = 8.0VPP sine wave
VIS = 11.0VPP sine wave
U i
Unit
25°C
‘51
‘52
‘53
80
80
80
95
95
95
120
120
120
MHz
dB
mVPP
dB
%
2.25
4.50
6.00
–2.25
–4.50
–6.00
0.10
0.08
0.05
* Limits not tested. Determined by design and verified by qualification.
MOTOROLA
6
High–Speed CMOS Logic Data
DL129 — Rev 6
250
Ron , ON RESISTANCE (OHMS)
Ron , ON RESISTANCE (OHMS)
MC54/74HC4051A MC74HC4052A MC54/74HC4053A
200
125°C
150
25°C
TBD
100
– 55°C
50
0
0.25
0.50
0.75
1.0
1.25
1.5
1.75
2.0
100
125°C
80
25°C
60
TBD
– 55°C
40
20
2.25
0
0.5
VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE
25°C
Ron , ON RESISTANCE (OHMS)
Ron , ON RESISTANCE (OHMS)
75
60
TBD
45
– 55°C
30
15
0
0.5
1.0
1.5 2.0
2.5
3.0
3.5
4.0 4.5
5.0
5.5
2.0
2.5
3.0
4.0
3.5
4.5
Figure 1b. Typical On Resistance, VCC – VEE = 4.5 V
105
125°C
1.5
VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE
Figure 1a. Typical On Resistance, VCC – VEE = 2.0 V
90
1.0
75
125°C
60
25°C
45
TBD
– 55°C
30
15
0
6.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE
VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE
Figure 1c. Typical On Resistance, VCC – VEE = 6.0 V
Figure 1d. Typical On Resistance, VCC – VEE = 9.0 V
PLOTTER
Ron , ON RESISTANCE (OHMS)
70
60
125°C
50
25°C
40
PROGRAMMABLE
POWER
SUPPLY
TBD
–
MINI COMPUTER
+
VCC
– 55°C
30
DEVICE
UNDER TEST
20
10
ANALOG IN
0
1.0 2.0
3.0
4.0
5.0 6.0
7.0
8.0 9.0 10.0 11.0 12.0
GND
VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE
Figure 1e. Typical On Resistance, VCC – VEE = 12.0 V
High–Speed CMOS Logic Data
DL129 — Rev 6
DC ANALYZER
COMMON OUT
VEE
Figure 2. On Resistance Test Set–Up
7
MOTOROLA
MC54/74HC4051A MC74HC4052A MC54/74HC4053A
VCC
VCC
VCC
16
VEE
ANALOG I/O
OFF
A
VCC
OFF
NC
VIH
OFF
VIH
6
7
8
VEE
COMMON O/I
6
7
8
VEE
Figure 3. Maximum Off Channel Leakage Current,
Any One Channel, Test Set–Up
VCC
Figure 4. Maximum Off Channel Leakage Current,
Common Channel, Test Set–Up
VCC
16
A
VEE
VCC
16
0.1µF
fin
ON
COMMON O/I
OFF
VCC
OFF
VCC
COMMON O/I
VCC
16
VEE
VOS
dB
METER
ON
N/C
RL
CL*
ANALOG I/O
VIL
6
7
8
6
7
8
VEE
VEE
Figure 5. Maximum On Channel Leakage Current,
Channel to Channel, Test Set–Up
VCC
16
VIS
0.1µF
fin
Figure 6. Maximum On Channel Bandwidth,
Test Set–Up
VCC
16
VOS
dB
METER
OFF
RL
*Includes all probe and jig capacitance
CL*
RL
ON/OFF
COMMON O/I
ANALOG I/O
RL
OFF/ON
RL
RL
6
7
8
VEE
VIL or VIH
CHANNEL SELECT
Vin ≤ 1 MHz
tr = tf = 6 ns
VEE
VCC
GND
*Includes all probe and jig capacitance
CL*
VCC
11
CHANNEL SELECT
*Includes all probe and jig capacitance
Figure 7. Off Channel Feedthrough Isolation,
Test Set–Up
MOTOROLA
6
7
8
TEST
POINT
Figure 8. Feedthrough Noise, Channel Select to
Common Out, Test Set–Up
8
High–Speed CMOS Logic Data
DL129 — Rev 6
MC54/74HC4051A MC74HC4052A MC54/74HC4053A
VCC
16
VCC
VCC
CHANNEL
SELECT
ON/OFF
50%
COMMON O/I
ANALOG I/O
OFF/ON
GND
tPLH
TEST
POINT
CL*
tPHL
ANALOG
OUT
6
7
8
50%
CHANNEL SELECT
*Includes all probe and jig capacitance
Figure 9a. Propagation Delays, Channel Select
to Analog Out
Figure 9b. Propagation Delay, Test Set–Up Channel
Select to Analog Out
VCC
16
ANALOG
IN
COMMON O/I
ANALOG I/O
VCC
ON
50%
TEST
POINT
CL*
GND
tPLH
tPHL
ANALOG
OUT
6
7
8
50%
*Includes all probe and jig capacitance
Figure 10a. Propagation Delays, Analog In
to Analog Out
tf
tr
90%
50%
10%
ENABLE
tPZL
ANALOG
OUT
Figure 10b. Propagation Delay, Test Set–Up
Analog In to Analog Out
tPLZ
1
VCC
2
GND
50%
1
TEST
POINT
ON/OFF
CL*
ENABLE
90%
1kΩ
ANALOG I/O
2
VOL
tPZH tPHZ
ANALOG
OUT
VCC
16
VCC
HIGH
IMPEDANCE
10%
POSITION 1 WHEN TESTING tPHZ AND tPZH
POSITION 2 WHEN TESTING tPLZ AND tPZL
VOH
50%
6
7
8
HIGH
IMPEDANCE
Figure 11a. Propagation Delays, Enable to
Analog Out
High–Speed CMOS Logic Data
DL129 — Rev 6
Figure 11b. Propagation Delay, Test Set–Up
Enable to Analog Out
9
MOTOROLA
MC54/74HC4051A MC74HC4052A MC54/74HC4053A
VCC
VIS
A
VCC
16
RL
fin
16
VOS
ON
ON/OFF
COMMON O/I
NC
ANALOG I/O
0.1µF
OFF/ON
OFF
VEE
RL
RL
CL*
RL
CL*
6
7
8
VEE
VCC
6
7
8
11
CHANNEL SELECT
*Includes all probe and jig capacitance
Figure 12. Crosstalk Between Any Two
Switches, Test Set–Up
Figure 13. Power Dissipation Capacitance,
Test Set–Up
0
VIS
VCC
16
0.1µF
fin
– 10
VOS
ON
CL*
– 20
TO
DISTORTION
METER
– 30
– 40
dB
RL
FUNDAMENTAL FREQUENCY
– 50
DEVICE
– 60
6
7
8
VEE
SOURCE
– 70
– 80
– 90
*Includes all probe and jig capacitance
– 100
1.0
2.0
3.125
FREQUENCY (kHz)
Figure 14a. Total Harmonic Distortion, Test Set–Up
Figure 14b. Plot, Harmonic Distortion
APPLICATIONS INFORMATION
The Channel Select and Enable control pins should be at
VCC or GND logic levels. VCC being recognized as a logic
high and GND being recognized as a logic low. In this example:
VCC = +5V = logic high
GND = 0V = logic low
The maximum analog voltage swings are determined by
the supply voltages VCC and VEE. The positive peak analog
voltage should not exceed VCC. Similarly, the negative peak
analog voltage should not go below VEE. In this example, the
difference between VCC and VEE is ten volts. Therefore,
using the configuration of Figure 15, a maximum analog signal of ten volts peak–to–peak can be controlled. Unused
analog inputs/outputs may be left floating (i.e., not connected). However, tying unused analog inputs and outputs to
MOTOROLA
VCC or GND through a low value resistor helps minimize
crosstalk and feedthrough noise that may be picked up by an
unused switch.
Although used here, balanced supplies are not a requirement. The only constraints on the power supplies are that:
VCC – GND = 2 to 6 volts
VEE – GND = 0 to –6 volts
VCC – VEE = 2 to 12 volts
and VEE ≤ GND
When voltage transients above VCC and/or below VEE are
anticipated on the analog channels, external Germanium or
Schottky diodes (Dx) are recommended as shown in Figure
16. These diodes should be able to absorb the maximum
anticipated current surges during clipping.
10
High–Speed CMOS Logic Data
DL129 — Rev 6
MC54/74HC4051A MC74HC4052A MC54/74HC4053A
VCC
+5V
16
+5V
ANALOG
SIGNAL
–5V
ON
6
7
8
Dx
+5V
ANALOG
SIGNAL
VCC
16
Dx
Dx
VEE
VEE
7
8
–5V
VEE
Figure 15. Application Example
Figure 16. External Germanium or
Schottky Clipping Diodes
+5V
+5V
16
+5V
ANALOG
SIGNAL
VEE
Dx
ON/OFF
–5V
TO EXTERNAL CMOS
CIRCUITRY 0 to 5V
DIGITAL SIGNALS
11
10
9
VCC
ON/OFF
6
7
8
VEE
ANALOG
SIGNAL
+5V
*
R
R
11
10
9
+5V
+5V
VEE
VEE
16
ANALOG
SIGNAL
ON/OFF
+5V
ANALOG
SIGNAL
R
VEE
+5V
6
7
8
LSTTL/NMOS
CIRCUITRY
VEE
* 2K ≤ R ≤ 10K
a. Using Pull–Up Resistors
11
10
9
LSTTL/NMOS
CIRCUITRY
HCT
BUFFER
b. Using HCT Interface
Figure 17. Interfacing LSTTL/NMOS to CMOS Inputs
A
11
13
LEVEL
SHIFTER
14
B
10
15
LEVEL
SHIFTER
12
C
9
1
LEVEL
SHIFTER
5
ENABLE
6
2
LEVEL
SHIFTER
4
3
Figure 18. Function Diagram, HC4051A
High–Speed CMOS Logic Data
DL129 — Rev 6
11
X0
X1
X2
X3
X4
X5
X6
X7
X
MOTOROLA
MC54/74HC4051A MC74HC4052A MC54/74HC4053A
A
10
12
LEVEL
SHIFTER
14
B
9
15
LEVEL
SHIFTER
11
13
ENABLE
6
1
LEVEL
SHIFTER
5
2
4
3
X0
X1
X2
X3
X
Y0
Y1
Y2
Y3
Y
Figure 19. Function Diagram, HC4052A
A
11
13
LEVEL
SHIFTER
12
14
B
10
1
LEVEL
SHIFTER
2
15
C
9
3
LEVEL
SHIFTER
5
4
ENABLE
6
X1
X0
X
Y1
Y0
Y
Z1
Z0
Z
LEVEL
SHIFTER
Figure 20. Function Diagram, HC4053A
MOTOROLA
12
High–Speed CMOS Logic Data
DL129 — Rev 6
MC54/74HC4051A MC74HC4052A MC54/74HC4053A
OUTLINE DIMENSIONS
J SUFFIX
CERAMIC PACKAGE
CASE 620–10
ISSUE V
–A
–
16
9
1
8
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
4. DIM F MAY NARROW TO 0.76 (0.030) WHERE
THE LEAD ENTERS THE CERAMIC BODY.
–B
–
L
C
DIM
A
B
C
D
E
F
G
J
K
L
M
N
–T
K
N
SEATING
–
PLANE
E
M
F
J 16 PL
0.25 (0.010)
G
D 16 PL
0.25 (0.010)
T A
M
9
1
8
T B
N SUFFIX
PLASTIC PACKAGE
CASE 648–08
ISSUE R
–A
–
16
M
C
DIM
A
B
C
D
F
G
H
J
K
L
M
S
L
S
–T
–
SEATING
PLANE
K
H
D 16 PL
0.25 (0.010)
M
M
J
G
T A
M
D SUFFIX
PLASTIC SOIC PACKAGE
CASE 751B–05
ISSUE J
–A
–
16
1
P 8 PL
0.25 (0.010)
8
M
B
M
G
K
F
R X 45°
C
–T
SEATING
–
PLANE
J
M
D 16 PL
0.25 (0.010)
High–Speed CMOS Logic Data
DL129 — Rev 6
M
T
B
S
A
S
13
INCHES
MILLIMETERS
MIN
MAX
MIN
MAX
0.740 0.770 18.80 19.55
0.250 0.270
6.35
6.85
0.145 0.175
3.69
4.44
0.015 0.021
0.39
0.53
0.040 0.070
1.77
1.02
0.100 BSC
2.54 BSC
0.050 BSC
1.27 BSC
0.008 0.015
0.21
0.38
0.110 0.130
2.80
3.30
0.295 0.305
7.50
7.74
0°
10°
0°
10°
0.020 0.040
0.51
1.01
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
9
–B
–
MILLIMETERS
MIN
MAX
19.05 19.93
6.10
7.49
—
5.08
0.39
0.50
1.27 BSC
1.40
1.65
2.54 BSC
0.21
0.38
3.18
4.31
7.62 BSC
15°
0°
1.01
0.51
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
B
F
S
S
INCHES
MIN
MAX
0.750 0.785
0.240 0.295
—
0.200
0.015 0.020
0.050 BSC
0.055 0.065
0.100 BSC
0.008 0.015
0.125 0.170
0.300 BSC
15°
0°
0.020 0.040
DIM
A
B
C
D
F
G
J
K
M
P
R
MILLIMETERS
MIN
MAX
9.80 10.00
4.00
3.80
1.75
1.35
0.49
0.35
1.25
0.40
1.27 BSC
0.25
0.19
0.25
0.10
7°
0°
6.20
5.80
0.50
0.25
INCHES
MIN
MAX
0.386 0.393
0.150 0.157
0.054 0.068
0.014 0.019
0.016 0.049
0.050 BSC
0.008 0.009
0.004 0.009
0°
7°
0.229 0.244
0.010 0.019
MOTOROLA
MC54/74HC4051A MC74HC4052A MC54/74HC4053A
OUTLINE DIMENSIONS
DW SUFFIX
PLASTIC SOIC PACKAGE
CASE 751G–02
ISSUE A
–A–
16
9
–B–
8X
P
0.010 (0.25)
1
B
M
M
8
16X
J
D
0.010 (0.25)
M
T A
S
B
NOTES:
1. DIMENSIONING AND TOLERANCING
PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER
SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.13 (0.005) TOTAL IN
EXCESS OF D DIMENSION AT MAXIMUM
MATERIAL CONDITION.
S
DIM
A
B
C
D
F
G
J
K
M
P
R
F
R X 45 _
C
–T–
14X
G
K
0.10 (0.004)
M
T U
V
S
S
S
ÉÉ
ÇÇ
ÇÇ
ÉÉ
ÇÇ
ÉÉ
K
K1
2X
L/2
16
9
J1
B
–U–
L
SECTION N–N
J
PIN 1
IDENT.
8
1
N
0.25 (0.010)
0.15 (0.006) T U
S
A
–V–
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH.
PROTRUSIONS OR GATE BURRS. MOLD FLASH OR
GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER
SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH OR
PROTRUSION SHALL NOT EXCEED
0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K
DIMENSION AT MAXIMUM MATERIAL CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE DETERMINED AT
DATUM PLANE –W–.
M
N
F
DETAIL E
–W–
C
0.10 (0.004)
–T– SEATING
PLANE
MOTOROLA
H
D
INCHES
MIN
MAX
0.400
0.411
0.292
0.299
0.093
0.104
0.014
0.019
0.020
0.035
0.050 BSC
0.010
0.012
0.004
0.009
0_
7_
0.395
0.415
0.010
0.029
DT SUFFIX
PLASTIC TSSOP PACKAGE
CASE 948F–01
ISSUE O
16X K REF
0.15 (0.006) T U
M
SEATING
PLANE
MILLIMETERS
MIN
MAX
10.15
10.45
7.40
7.60
2.35
2.65
0.35
0.49
0.50
0.90
1.27 BSC
0.25
0.32
0.10
0.25
0_
7_
10.05
10.55
0.25
0.75
DETAIL E
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
MILLIMETERS
MIN
MAX
4.90
5.10
4.30
4.50
–––
1.20
0.05
0.15
0.50
0.75
0.65 BSC
0.18
0.28
0.09
0.20
0.09
0.16
0.19
0.30
0.19
0.25
6.40 BSC
0_
8_
INCHES
MIN
MAX
0.193
0.200
0.169
0.177
–––
0.047
0.002
0.006
0.020
0.030
0.026 BSC
0.007
0.011
0.004
0.008
0.004
0.006
0.007
0.012
0.007
0.010
0.252 BSC
0_
8_
G
14
High–Speed CMOS Logic Data
DL129 — Rev 6
MC54/74HC4051A MC74HC4052A MC54/74HC4053A
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
Mfax is a trademark of Motorola, Inc.
How to reach us:
USA / EUROPE / Locations Not Listed: Motorola Literature Distribution;
P.O. Box 5405, Denver, Colorado 80217. 1–303–675–2140 or 1–800–441–2447
JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 4–32–1,
Nishi–Gotanda, Shinagawa–ku, Tokyo 141, Japan. 81–3–5487–8488
Customer Focus Center: 1–800–521–6274
Mfax: [email protected] – TOUCHTONE 1–602–244–6609
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
Motorola Fax Back System
– US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
– http://sps.motorola.com/mfax/
HOME PAGE: http://motorola.com/sps/
High–Speed CMOS Logic Data
DL129 — Rev 6
◊
15
MC74HC4051A/D
MOTOROLA
Similar pages